OPERATION AND PARTS MANUAL
SERIES
WM120PH Series
POLYETHYLENE DRUM
WM120SH Series
STEEL DRUM
HYDRAULIC PLASTER/MORTAR MIXERS
(HONDA GASOLINE ENGINE/ELECTRIC MOTOR)
Revision #7 (09/15/11)
To find the latest revision of this
publication, visit our website at:
www.multiquip.com
THIS MANUAL MUST ACCOMPANYTHE EQUIPMENT AT ALLTIMES.
Download from Www.Somanuals.com. All Manuals Search And Download.
PROPOSITION 65 WARNING
Engine exhaust and some of
its constituents,and some dust created
by power sanding, sawing, grinding,
drillingandotherconstructionactivities
contains chemicals known to the State
of California to cause cancer, birth
defects and other reproductive harm.
Someexamplesofthesechemicalsare:
Leadfromlead-basedpaints.
Crystallinesilicafrombricks.
Cementandothermasonryproducts.
Arsenicandchromiumfromchemically
treatedlumber.
Your risk from these exposures varies,
dependingonhowoftenyoudothistype
of work. To reduce your exposure to
these chemicals: ALWAYS work in a
well ventilated area, and work with
approved safety equipment, such as
dust masks that are specially designed
to filter out microscopic particles.
PAGE 2 — WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
SILICOSIS/RESPIRATORY WARNINGS
WARNING WARNING
SILICOSIS WARNING
RESPIRATORY HAZARDS
Grinding/cutting/drilling of masonry, concrete, metal and
other materials with silica in their composition may give
off dust or mists containing crystalline silica. Silica is a
basic component of sand, quartz, brick clay, granite and
numerous other minerals and rocks. Repeated and/or
substantial inhalation of airborne crystalline silica can
cause serious or fatal respiratory diseases, including
silicosis. In addition, California and some other
authorities have listed respirable crystalline silica as a
substance known to cause cancer. When cutting such
materials, always follow the respiratory precautions
mentioned above.
Grinding/cutting/drilling of masonry, concrete, metal and
other materials can generate dust, mists and fumes
containing chemicals known to cause serious or fatal
injury or illness, such as respiratory disease, cancer,
birth defects or other reproductive harm. If you are
unfamiliar with the risks associated with the particular
process and/or material being cut or the composition of
the tool being used, review the material safety data
sheet and/or consult your employer, the material
manufacturer/supplier, governmental agencies such as
OSHA and NIOSH and other sources on hazardous
materials. California and some other authorities, for
instance, have published lists of substances known to
cause cancer, reproductive toxicity, or other harmful
effects.
Control dust, mist and fumes at the source where
possible. In this regard use good work practices and
follow the recommendations of the manufacturers or
suppliers, OSHA/NIOSH, and occupational and trade
associations. Water should be used for dust
suppression when wet cutting is feasible. When the
hazards from inhalation of dust, mists and fumes cannot
be eliminated, the operator and any bystanders should
always wear a respirator approved by NIOSH/MSHA for
the materials being used.
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 3
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
Hydraulic Assembly.......................................... 54-55
Frame 1 Assembly ........................................... 56-57
Frame 2 Assembly ........................................... 58-59
Frame 3 Assembly ........................................... 60-61
Plastic Engine Cover Assembly ....................... 62-63
Steel Engine Cover Assembly.......................... 64-65
Single Phase, 5 HP Electric Motor Assembly .. 66-67
Three Phase, 5 HP Electric Motor Assembly... 68-69
WM120PH/SH HYDRAULIC
MIXER
Proposition 65 Warning ........................................... 2
Silicosis/Respiratory Warnings ................................ 3
Table of Contents .................................................... 4
Parts Ordering Procedures ..................................... 5
Safety ...................................................................... 6
Safety ...................................................................... 7
Rules and Regulations ....................................... 8-10
Towing Guidelines ................................................. 11
Safety Chain Connection ...................................... 12
Specifications ........................................................ 13
Dimensions ........................................................... 14
General Information .............................................. 15
Mixer Components........................................... 16-17
Hydraulic Components.......................................... 17
Engine Components ............................................. 18
Electric Motor Components .................................. 19
Paddle Blade Adjustment (Steel Drum) ................ 20
Paddle Blade Adjustment (Poly Drum) .................. 21
Inspection......................................................... 22-23
Initial Start-Up (Gasoline) ..................................... 24
Initial start-up (Electric)......................................... 25
Operation ......................................................... 25-26
Shut-Down ............................................................ 27
Maintenance (Engine)...................................... 28-29
Maintenance (Mixer) ........................................ 30-33
Storage ................................................................. 33
Troubleshooting (Engine)................................. 34-35
Troubleshooting (Mixer/Electric motor) ................. 36
Wiring Diagram (Electric Motor)............................ 37
Hydraulic System Diagram ................................... 38
Explanation of Code in Remarks Column ............. 40
Suggested Spare Parts ......................................... 41
HONDA GX390K1QA2/
GX390U1QA2 Engine
Honda Engine Assembly .................................. 70-71
Air Cleaner Assembly....................................... 72-73
Camshaft Assembly ......................................... 74-75
Piston Assembly............................................... 76-77
Crankcase Cover Assembly............................. 78-79
Crankshaft Assembly ....................................... 80-81
Cylinder Barrel Assembly................................. 82-83
Cylinder Head Assembly .................................. 84-85
Fan Cover Assembly ........................................ 86-87
Flywheel Assembly .......................................... 88-89
Ignition Coil Assembly ...................................... 90-91
Carburetor Assembly ....................................... 92-93
Muffler Assembly ............................................. 94-95
Recoil Starter Assembly................................... 96-97
Control Assembly ............................................. 98-99
Fuel Tank Assembly ..................................... 100-101
Gasket Kit Assembly .................................... 102-103
Labels Assembly .......................................... 104-105
Terms and Conditions of Sale — Parts ............... 106
In accordance with our established policy of
constant improvement, we reserve the right to
amend these specifications at any time without
notice.
Component Drawings
Nameplate and Decals..................................... 42-43
Paddle Blades Assembly.................................. 44-45
Plastic Mixing Drum Assembly ......................... 46-47
Steel Drum Assembly (Manual) ....................... 48-49
Steel Drum Assembly (Hydraulic) .................... 50-51
Paddle Shaft Assembly (Plastic/Steel) ............. 52-53
Specifications and part numbers are
subject to change without notice.
PAGE 4 — WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS ORDERING PROCEDURES
Ordering parts has never been easier!
Choose from three easy options:
Effective:
January 1st, 2006
Best Deal!
Order via Internet (Dealers Only)
Order parts on-line using Multiquip’s SmartEquip website!
:
If you have an MQ Account, to obtain a Username
and Password, E-mail us at: parts@multiquip.
com.
N View Parts Diagrams
N Order Parts
N Print Specification Information
To obtain an MQ Account, contact your
District Sales Manager for more information.
Use the internet and qualify for a 5% Discount
on Standard orders for all orders which include
complete part numbers.*
Goto www.multiquip.com and click on
to log in and save!
Order Parts
Note: Discounts Are Subject To Change
Fax your order in and qualify for a 2% Discount
on Standard orders for all orders which include
complete part numbers.*
Order via Fax (Dealers Only)
:
All customers are welcome to order parts via Fax.
Domestic (US) Customers dial:
1-800-6-PARTS-7 (800-672-7877)
Note: Discounts Are Subject To Change
Domestic (US) Dealers Call:
Order via Phone:
1-800-427-1244
Non-Dealer Customers:
International Customers should contact
their local Multiquip Representatives for
Parts Ordering information.
Contact your local Multiquip Dealer for
parts or call 800-427-1244 for help in
locating a dealer near you.
When ordering parts, please supply:
R
Dealer Account Number
R
Specify Preferred Method of Shipment:
R
R
R
R
R
Dealer Name and Address
ꢀ UPS/Fed Ex
ꢀ DHL
ꢀ Truck
N
N
Priority One
Ground
Shipping Address (if different than billing address)
Return Fax Number
N Next Day
Second/Third Day
Applicable Model Number
N
Quantity, Part Number and Description of Each Part
NOTICE
All orders are treated as Standard Orders and will
ship the same day if received prior to 3PM PST.
WE ACCEPT ALL MAJOR CREDIT CARDS!
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 5
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
FORYOUR SAFETY AND SAFETY OF OTHERS!
HAZARD SYMBOLS
Safety precautions should be followed at all
times when operating this equipment. Failure
to read and understand the Safety Messages
and Operating Instructions could result in injury
to yourself and others.
Potential hazards associated with the operation of this
equipment will be referenced with Hazard Symbols which
appear throughout this manual, and will be referenced in
conjunction with Safety Message Alert Symbols.
WARNING — Lethal Exhaust Gas Hazards
Engine fuel exhaust gases contain poisonous
carbon monoxide. This gas is colorless and
odorless, and can cause death if inhaled.
NEVER operate this equipment in a confined
area or enclosed structure that does not
provide ample free flow air.
This manual has been developed to
provide complete instructions for the
safe and efficient operation of this
equipment. Refer to the engine
manufacturer's instructions for data
relative to its safe operation.
Before using this equipment ensure that the operating
individual has read and understood all instructions in this
manual.
WARNING — Explosive Fuel Hazards
Fuel is extremely flammable and its
vapors can cause an explosion if ignited.
DO NOT start the engine near spilled fuel
or combustible fluids.
SAFETY MESSAGE ALERT SYMBOLS
The three Safety Messages shown below will inform you
about potential hazards that could injure you or others. The
Safety Messages specifically address the level of exposure
to the operator, and are preceded by one of three words:
DANGER,WARNING, or CAUTION.
DO NOT fill the fuel tank while the engine
is running or hot. DO NOT overfill tank, since spilled
fuel could ignite if it comes into contact with hot engine
parts or sparks from the ignition system. Store fuel in
approved containers, in well-ventilated areas and away
from sparks and flames.
DANGER
You WILL be KILLED or SERIOUSLY INJURED if you
DO NOT follow these directions.
WARNING — Burn Hazards
Engine components can generate extreme
heat. To prevent burns, DO NOT touch
these areas while the engine is running or
immediately after operation. Never operate
the engine with heat shields or heat guards
removed.
WARNING
You CAN be KILLED or SERIOUSLY INJURED if you
DO NOT follow these directions.
WARNING — Respiratory Hazards
CAUTION
ALWAYS wear approved respiratory
protection when required.
You CAN be INJURED if you DO NOT follow these
directions.
PAGE 6 — WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
CAUTION — Rotating Parts Hazards
CAUTION — Overspeed Conditions
NEVER operate equipment with covers or
guards removed. Keep fingers, hands, hair
and clothing away from all moving parts
to prevent injury.
NEVER tamper with the factory setting of
the engine governor. Personal injury and
equipment damage can result if operating
in speed ranges above the maximum
allowable.
CAUTION — Equipment Damage Hazards
CAUTION — Accidental Starting Hazards
Other important messages are provided throughout this
manual to help prevent damage to your equipment, other
property, or the surrounding environment.
ALWAYS place the equipment ON/OFF
switch in the OFF position when the
equipment is not in use.
CAUTION — Start/Stop Switch
CAUTION — Eye and Hearing Hazards
ALWAYS test the start/stop switch for the gasoline
engine or electric motor every time the engine or electric
motor is started.
ALWAYS wear approved eye and hearing
protection.
WARNING — Stand Clear of Mixer
Always stand clear of the dump handle when the mixer
is in operation. Any binding of material between the mixer
blades and the drum will cause the drum handle to
quickly move and could cause bodily harm.
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 7
Download from Www.Somanuals.com. All Manuals Search And Download.
RULES AND REGULATIONS
NEVER touch the hot exhaust manifold,
muffler or cylinder.Allow these parts to cool
before servicing engine or pump.
WARNING — ReadThis Manual
Failure to follow instructions in this manual may lead to
serious injury or even DEATH! This equipment is to be
operated by trained and qualified personnel only! This
equipment is for industrial use only.
ALWAYS allow the engine to cool before
adding fuel or performing service and maintenance
functions. Contact with hot components can cause
serious burns.
GENERAL SAFETY
NEVER operate this equipment in any enclosed or narrow
area where free flow of the air is restricted. The engine
of this equipment requires an adequate free flow of
cooling air. If the air flow is
restricted it will cause serious
damage to the equipment or
engine and may cause injury
to people and property.
Remember the engine gives
DO NOT operate or service this equipment
before reading this entire manual.
This equipment should not be operated by
persons under 18 years of age.
NEVER operate this equipment without proper protective
clothing, shatterproof glasses, steel-toed boots and other
protective devices required by the job.
off DEADLY gases.
ALWAYS refuel in a well-ventilated area, away from
sparks and open flames.
NEVER operate this equipment when not
feeling well due to fatigue, illness or when
under medication.
ALWAYS use extreme caution when working with
flammable liquids.When refueling, stop the engine and
allow it to cool.
NEVER operate this equipment under the
influence of drugs or alcohol.
DO NOT smoke around or near the
equipment. Fire or explosion could result
from fuel vapors, or if fuel is spilled on a
hot engine.
NEVER operate the equipment in an
explosive atmosphere or near combustible
materials. An explosion or fire could result
causing severe bodily harm or even
death.
NEVER disconnect any "emergency or safety
devices".These devices are intended for operator safety.
Disconnection of these devices can cause severe injury,
bodily harm or even death! Disconnection of any of these
devices will void all warranties.
DO NOT top-off fuel tank.Topping-off is dangerous as it
causes fuel to spill.
NEVER use accessories or attachments that are not
recommended by Multiquip for this equipment. Damage
to the equipment and/or injury to user may result.
ALWAYS store the equipment in a clean, dry location
out of the reach of children.
NEVER run engine without air cleaner or air filter.Severe
engine damage may occur.
Manufacturer does not assume responsibility for any
accident due to equipment modifications. Unauthorized
equipment modification will void all warranties.
NEVER leave the equipment unattended with the engine
running.Turn off engine when unattended.
Whenever necessary, replace nameplate, operation and
safety decals when they become difficult read.
CAUTION must always be observed while servicing this
equipment. Rotating parts can cause injury if contacted.
ALWAYS check the equipment for loosened threads or
bolts before starting.
PAGE 8 — WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
RULES AND REGULATIONS
When towing, an adequate safety chain must be
fastened to the frame. See Towing Guidelines section in
this manual.
WARNING — Manual Dump Drum Handle
Always stand clear of dump handle when equipment is in
operation.
Keep all inexperienced and unauthorized people away
from the equipment at all times.
technical questions or information recommended by
Multiquip for this equipment. Damage to the equipment
and/or injury to user may result.
Unauthorized equipment modifications will void all
warranties.
TRANSPORTING
Check all fasteners periodically for tightness. Also check
towing tongue bolt, lock nut and wheel lug nuts for wear.
ALWAYS shutdown engine before transporting.
Stop the engine and disconnect the spark plug before
allowing anybody’s hands in the mixing drum.
Tighten fuel tank cap securely and close fuel cock to
prevent fuel from spilling.
NEVER pour or spray water over the engine or electric
motor.
Drain fuel when transporting equipment over long
distances or bad roads.
When towing, an adequate safety chain must be
fastened to the frame. See Towing Guidelines section in
this manual.
MAINTENANCE SAFETY
NEVER lubricate components or attempt service on a
running machine.
Keep all inexperienced and unauthorized people away
from the equipment at all times.
ALWAYS allow the machine a proper amount of time to
cool before servicing.
Unauthorized equipment modifications will void all
warranties.
Keep the equipment in proper running condition.
Check all fasteners periodically for tightness. Also check
towing tongue bolt, lock nut and wheel lug nuts for wear.
Fix damage to the equipment immediately and always
replace broken parts.
Stop the engine and disconnect the spark plug before
allowing anybody’s hands in the mixing drum.
Dispose of hazardous waste properly. Examples of
potentially hazardous waste are used motor oil, fuel and
fuel filters.
NEVER pour or spray water over the engine or electric
motor.
DO NOT use food or plastic containers to dispose of
hazardous waste.
Depending on type of mixer, test the ON/OFF switch for
either the gasoline engine or electric motor before
operating.The purpose of these switches is to shut down
the engine or motor of the mixer
DO NOT pour waste, oil or fuel directly onto the ground,
down a drain or into any water source.
ALWAYS stand clear of the release drum lock. Move
handle downward to empty the drum. Move handle upward
to return to vertical position. Inspect for proper
functionality before starting engine or engaging blades.
Any binding of material between the mixing blades &
drum will cause the handle to quickly rotate if not in the
"up & locked" position.
DO NOT operate this equipment unless all guards and
safety devices are attached and in place.
Refer to the HONDA Engine Owner's Manual for engine
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 9
Download from Www.Somanuals.com. All Manuals Search And Download.
RULES AND REGULATIONS
EMERGENCIES
ALWAYS know the location of the nearest
fire extinguisher.
ALWAYS know the location of the nearest
first aid kit.
In emergencies, always know the location
of the nearest phone or keep a phone on the job site.
Also know the phone numbers of the nearest
ambulance, doctor and fire department. This
information will be invaluable in case of emergency.
PAGE 10 —WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
TOWING GUIDELINES
ALWAYS make sure that the fuel valve lever is in the
OFF position (gasoline models only).
TOWING SAFETY PRECAUTIONS
CAUTION — InspectTowing Components
Check wheel mounting lug nuts with a torque wrench.
Torque wheel lug nuts as described in the maintenance
section of this manual.
To reduce the possibility of an accident while transporting
the machine on public roads, always make sure that the
equipment’s towing components and the towing vehicle
are in good operating condition and both units are
mechanically sound. Remember before towing, check with
local and state laws for proper compliance.
Check tightness of U-clamp nuts, torque suspension
hardware as referenced in the maintenance section of this
manual.
Avoid sudden stops and starts.This can cause skidding,
or jackknifing. Smooth, gradual starts and stops will
improve gas milage.
The following list of suggestions should be used when towing
the mixer:
Check with your county or state safety towing regulations
Avoid sharp turns to prevent rolling.
department before towing your mixer.
Tow bar to vehichle connection (Coupler only)
Make sure that the hitch and coupling of the towing
vehicle are rated equal to, or greater than the trailer "gross
vehicle weight rating" (GVWR).
1. Check the vehicle hitch ball, and mixer's coupler for
signs of wear or damage. Replace any parts that are
worn or damaged before towing.
ALWAYS inspect the hitch and coupling for wear.NEVER
tow the mixer with defective hitches, couplings, chains
etc.
2. Use only a 2-inch ball diameter (towing vehicle), this will
CAUTION — Replacing Towing Components
CHECK the tire air pressure on both the towing vehicle
and the trailer. Also check the tire tread wear on both
vehicles.
If the mixer tow bar is deformed or damaged, replace
the entire tow bar.NEVER tow the mixer with a defective
tow bar. There exists the possibility of the mixer
separating from the towing vehicle.
ALWAYS make sure the mixer is equipped with a“Safety
Chain.”
ALWAYS attach trailer's safety chain to the frame of
towing vehicle.
match the mixer's 2-inch coupler. Use of any other ball
diameterwillcreateanextremelydangerousconditionwhich
can result in separation of the coupler and ball or ball
failure.
ALWAYS make sure that the towing vehicle's directional,
backup, and brake lights are working properly.
3. After tow bar has been connected to mixer (see next page),
attach mixer's coupler to the hitch ball on the towing vehicle
securely and make sure the lock lever is in the down
position (locked).
Remember in most cases the maximum speed unless
otherwise posted for highway towing is 55 MPH, however
before towing your mixer, check your local state, and
county vehicle towing requirements. Recommended off-
road towing is not to exceed 10 or 15 MPH or less
depending on type of terrain.
MixerTow BarVehicle Connection (Pentle and Loop)
1. Make sure the bumper on the towing vehicle is equipped
to handle either a pintle or loop type tow bar configuration.
Place chocked blocks underneath wheels to prevent
rolling, while parked, if disconnected from towing
vehicle.
2. After tow bar has been connected to mixer (see next page),
secure either type of tow bar to the towing vehicle, following
state and county towing regulations.
Inflate tires to correct pressure, inspect tires for cuts, and
excessive wear.SeeTable 9 (TireWearTroubleshooting).
3. As a minimum, use a 1/2-inch bolt and nylock nut grade 5
when securing the tow bar to the towing vehicle and to
the unit being towed.
When towing of the mixer is required, place the drum in the
up position (mouth facing upwards) and lock the drum latch.
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 11
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY CHAIN CONNECTION
2. Route the safety chain through the holes just above
the tow bar, located on each side of the mixer stand.
CAUTION — Tow With Safety Chain
NEVER! tow the mixer with the safety chain removed.
The safety chain is intended to prevent complete
separation of the mixer from the towing vehicle in the
event of a tow bar failure.
Loop the chain together and place under the tow bar.
Secure the loop with the connector link.
3. Extend the safety chain along the length of the tow
bar, looping it through the tow bar's connector link.
Remove any excess chain slack.
Reference Figure 1 for the installation of the safety chain.
4. Connect the free end of (clevis safety hook) the safety
chain to the towing vehicle. Remember it is critical that
the length of the chain be properly adjusted, to prevent
the draw bar and the front of the mixer stand from
dropping to the the ground (contact) in the event the
draw bar becomes disconnected from the towing
vehicle.
TOW BARTO MIXER CONNECTION
1. Insert the tow bar through the round opening at the
bottom of the mixer stand.
Align the hole on the tow bar with the hole on the mixer
frame, and insert 1/2-inch bolt through tow bar and
frame. Secure tow bar to frame with 1/2-inch nylock
nut. Tighten to 40 ft.-lbs.
If a new safety chain is required use P/N 13363.
For a new connector link use P/N 01004.
CAUTION — Drum Safety When Towing
DO NOT tow the mixer unless the mixing drum is
completely empty. ALWAYS make sure the drum lock
lever (Figure 24) is in the verticle position (manual dump
mixers only).
Figure 1. Tow Bar and Safety Chain Installation
PAGE 12 —WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
Table 1 Specifications Mixer
Drum Capacity
Discharge
Height
in. (cm.)
Mixer Model
Drum Capacity
cu. ft (liters)
94 lbs. (42 kg.)
Bag Portland
Cement
Weight
lbs. (kg.)
L x W x H in. (cm.)
Drive
Dump Action
From Stop
WM120SE1
1,040 (472)
1,065 (484)
1,050 (476)
1,075 (488)
1,085 (492)
1,110 (505)
Manual
Hydraulic
Manuall
Hydraulic
Manual
WM120SE1D
WM120SE3
84 x 56 x 62
(213 x 142 x 157)
WM120SE3D
WM120PHH
WM120SHHD
STEEL
12 (340)
3.5 to 4
18 (46)
Hydraulic
Hydraulic
84 x 56 x 62
(213 x 142 x 157)
WM120PHHDS*
1,400 (435)
Hydraulic
WM120PE1
WM120PE1D
WM120PE3
WM120PE3D
WM120PH
1,035 (469)
1,060 (481)
1,045 (475)
1,070 (486)
1,060 (481)
1,085 (493)
Manual
Hydraulic
Manual
87 x 59
(221 x 142)*
PLASTIC
12 (340)
3.5 to 4
18 (46)
Hydraulic
Hydraulic
Manual
WM120PHD
Hydraulic
Stationary mixer no wheels. Height is adjustable from 54-67 in. (1.4-1.7 m)
TABLE 2. SPECIFICATIONS (ENGINE/ELECTRIC MOTOR)
HONDA GX390K1QA2/
Model
BALDOR 3646LC
BALDOR 3634M
GX390U1QA2
Air-cooled 4 stroke,
Horizontal
Shaft Gasoline Engine
5 HP, 230 VAC, Single
Phase Electric Motor
5 HP, 230/460 VAC, Three
Phase Electric Motor
Type
3.46 in. X 2.51 in.
(88 mm x 64 mm)
Bore X Stroke
N/A
N/A
Displacement
Max Output
389 cc. (23.7 cu-in)
11.0 HP/3600 R.P.M
9.0 HP/3600 R.P.M
N/A
N/A
N/A
5.0 H.P./1750 RPM
N/A
5.0 H.P./1725 RPM
Engine/Electric
Motor
Continuous Output
Full Load Amps
N/A
23
13.4/6.7
Fuel Tank
Capacity
1.7 US gals.
(6.5 liters)
N/A
N/A
Fuel
Unleaded Gasoline
1.16 qts (1.1 liters)
N/A
N/A
N/A
N/A
Lube Oil Capacity
Speed Control
Method
Centrifugal Fly-weight
Type
N/A
N/A
N/A
N/A
Starting Method
Recoil Start
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 13
Download from Www.Somanuals.com. All Manuals Search And Download.
DIMENSIONS
Table 3. Dimensions
Description
Length
Dimensions in. (cm.)
84 in. (213 cm.)
56 in. (142 cm.)
62 in. (157 cm.)
Width
Height
Figure 2. Dimensions
PAGE 14 —WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL INFORMATION
Hardware
Application
Check all hardware on the mixer before starting.Periodically
inspect all hardware. Loose hardware can contribute to early
component failure and poor performance. Use Table 4 as
general guideline when torqueing of mixer hardware is
required. Remember to keep all mixer hardware components
tight.
The MQ WM120 series hydraulic mixers (drum capacity
12.0 cu. ft./340 liters) are shipped completely assembled
and have been factory tested and are ready for use.
This mixer is only intended for the mixing of plaster and
mortar. The mixer must be used for its intended purpose
and is not suitable for the mixing of flammable or explosive
substances. The mixer must not be used in an explosive
atmosphere.This mixer has a batch capacity between 3-1/
2 and 4-1/2 bags.
Engine Maintenance
For basic engine maintenance, refer to the engine
maintenance section in this manual. For a more detailed
engine maintenance, refer to the Honda Engine Owner's
manual furnished with the engine.
Power Plants
These hydraulic mixers can be powered by either a 11 HP
Honda GX390 air-cooled, 4-stroke gasoline engine or a 5.0
HP electric motor. Refer to Table 2 for specific engine or
electric motor data information.
Table 4. Hardware Torque
Recommendations
Hardware
Torque (ft-lbs)
Diameter
Electrical
5/16-inch x 18
3/8-inch x 16
3/8-inch x 24
1/2-inch x 13
14
24
37
39
90
If mixer is equipped with an electric motor, make sure
that the power being supplied to the motor corresponds to
the voltage rating label on the motor. Supplying the wrong
voltage to the electric motor will cause severe electrical
damage to the motor.
1/2-inch x 13
(Grade 8)
Always make sure the OFF/ON switch on the electric motor
is in the OFF position before applying power.
Extension Cables
The extension cable should be a 3-wire configuration that
includes a ground wire that conforms to UL code.The wire
cross section must be a minimum of 2.5 mm2. Choose an
extension cord of adequate current carrying capacity as
referenced in Table 5. Remember cable distance affects
the current-voltage capacity of the extension cable.
Ensure that the extension cable is carefully laid out avoiding
wet areas, sharp edges and locations where vehicles might
run over it.Avoid allowing the extension cable to be trapped
underneath the mixer.
Unroll the extension cable fully or it will overheat and could
catch fire. Make sure that all extension cable connections
are dry and safe. Replace any defective or badly worn
extension cable immediately.
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 15
Download from Www.Somanuals.com. All Manuals Search And Download.
MIXER COMPONENTS
9
7
9. Manual Dump Handle — Pull this handle downward
to dump the contents of the drum. Push the handle
upward to return the drum to its vertical position. This
feature is not available on hydraulic dump models.
8
6
5
10
11
10. Safety Grill Lock Handle —To prevent injury to hands
and arms, the safety grill should ALWAYS be locked
when the mixing of plaster or mortar is required. Also
when transporting the mixer the safety grill should be
locked.The safety grill should only be un-locked when
cleaning of the blades and drum is required.
3
13
12
4
2
14
11. Pivot Point/Zerk Fitting — There is a zerk grease
fitting on each end of the mixing drum. These fittings
lubricate the dumping mechanism. Lubricate both
fittings at least twice a week.
15
16
1
12. Drum Lock Lever — Rotate this lever horizontally to
lock the drum for mixing. Rotate vertically to release
the drum for dumping. This feature is not available on
hydraulic dump models.
Figure 3. Mixer Components (Wheels)
Figures 3 and 4 illustrate the basic components and controls
of the WM120 series hydraulic mixer
1. Tires — Replace with manufacturer recommeded tires
13. Mixing Drum — Mixing drums are available in two
types of materials plastic and steel. Drum capacity is
12 cu. ft (340 liters). Mixing materials such as mortar,
plaster are to be placed into this drum for mixing.
Always clean drum after each use.
only. This mixer requires 13-inch 4-ply tires.
2. Engine Cover — Lift this cover to gain access to the
engine or electric motor.
3. ON/OFF Switch (gasoline) — This switch is provided
on mixers with gasoline engines only and is located
on the side of the engine cover. When activated it will
shut down the engine.
14. Tow Bar/Coupler — This mixer uses a 2-inch coupler
or pintle towbar.
15. Safety Chain — This mixer uses a 3/16-inch thick,
72-inches long zinc-plated saftey chain. ALWAYS
connect the safety chain when towing.
4. Latch — Use this latch to secure the engine/electric
motor compartment enclosure.
16. Chock Blocks — Place these blocks (not included as
part of the mixer package) under each mixer wheel to
prevent rolling.
5. Drum Bearing — There is a sealed bearing on each
end of the mixing drum. Bearings are packed and sealed
at the factory and require no further maintenance.
6. Mixing Paddles —This mixer uses plastic and rubber
mixing paddles for the mixing of plaster and mortar.
Always clean paddles after each use.
7. Bag Cutter — This feature allows mixing bags to be
opened easily, therefore allowing the contents of the
bag to fall directly into the mixing drum.
8. Safety Grill — Provided for operator safety.This safety
grill is designed to keep hands and solid objects out of
the mixing drum when in use.This grill should be closed
at all times when mixer is in use. DO NOT remove the
grill or grill opening bar.Keep the grill clean by washing
it down daily.
PAGE 16 —WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
MIXER COMPONENTS/HYDRAULIC COMPONENTS
17
18
Figure 4. Mixer Components (Stationary)
17. Adjustable Stabilizer Jack Stands — Use these jack
stands (3) to adjust the mixer to the desired height.
18. Forklift Pockets —When lifting of the mixer is required,
use these fork lift pockets to lift the mixer. Remember
to insert the forks of the forklift a minimum of 24 inches
into the lift pockets.This feature is only available on
the stationary mixer model.
Figure 5. Hydraulic Components
5. Hydraulic Dump Lever — This lever is provided on
mixers with hydraulic dump capability only. Pull lever
outward to activate dump cylinder.
HYDRAULIC COMPONENTS
Figure 5 illustrates the hydraulic components used on the
mixer.
6. Hydraulic Paddle Blade Lever — 3-position lever.
Push inward for clockwise mixing rotation of blades.
Place in center position for no rotation (neutral/off).
1. Hydraulic Motor — Bi-directional hydraulic motor that
is used in conjunction with the directional control valve
to operate the hydraulic dump cylinder and paddle shaft.
7. Pump — Supplies hydraulic fluid to the hydraulic
control valve.
2. Hydraulic Dump Cylinder — When activated, this
cylinder will cause the mixing drum to rotate to the
dump position.This cylinder is provided only on mixers
with hydraulic dump capability only.
8. Hydraulic Oil Filter — 10 micron hydraulic filter. Filters
out small particles that are harmful to the hydraulic
system.
9. Strainer — Filters out large particles and debris that
3. Hydraulic Oil Sight Gauge — This gauge indicates
the level and temperature of the hydraulic oil. For normal
operation oil level should be visible at the midpoint on
the sightglass.
are harmful to the hydraulic system.
4. HydraulicValve — Directional hydraulic control valve.
Controls the direction of hydraulic fluid supplied to the
dump cylinder and paddle shaft.
Figure 5 shows configuration for electric motor.
Gasoline engine is configured in the same
manner.
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 17
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGINE COMPONENTS
4. Recoil Starter (pull rope) – Manual-starting method.
Pull the starter grip until resistance is felt, then pull
briskly and smoothly.
5. Fuel Valve Lever – OPEN to let fuel flow, CLOSE to
stop the flow of fuel.
6. Choke Lever – Used in the starting of a cold engine,
or in cold weather conditions. The choke enriches the
fuel mixture.
7. Air Cleaner – Prevents dirt and other debris from
entering the fuel system. Remove wing-nut on top of
air filter cannister to gain access to filter element.
Operating the engine without an air filter, with
a damaged air filter, or a filter in need of
replacement will allow dirt to enter the
engine, causing rapid engine wear.
Figure 6. Engine Controls and Components
INITIAL SERVICING
The engine (Figure 6) must be checked for proper lubrication
and filled with fuel prior to operation. Refer to the
manufacturers engine manual for instructions & details of
operation and servicing.
WARNING — Burn Hazards
Engine components can generate extreme
heat. To prevent burns, DO NOT touch
these areas while the engine is running or
immediately after operation. Never operate
the engine with the muffler removed.
1. Fuel Filler Cap – Remove this cap to add unleaded
gasoline to the fuel tank. Make sure cap is tightened
securely. DO NOT over fill.
DANGER — Explosive Fuel Hazards
8. Spark Plug – Provides spark to the ignition system.
Set spark plug gap to 0.6 - 0.7 mm (0.028 - 0.031 inch)
Clean spark plug once a week.
Fuel is extremely flammable and its
vapors can cause an explosion if ignited.
DO NOT start the engine near spilled fuel
or combustible fluids. In the event of a
fuel spill, wait until the fuel residue has
been completely wiped up and the area surrounding the
engine is dry before starting the engine.
9. Muffler – Used to reduce noise and emissions.
10. Fuel Tank – Holds unleaded gasoline. Fuel tank
capacity is 1.7 gallons (6.5 liters) For additional
information refer to engine owner's manual.
DO NOT fill the fuel tank while the engine is running or
hot. DO NOT overfill tank, since spilled fuel could ignite
if it comes into contact with hot engine parts or sparks
from the ignition system. Store fuel in approved
containers, in well-ventilated areas and away from
sparks and flames.
2. Throttle Lever – Used to adjust engine RPM speed
(lever advanced forward SLOW, lever back toward
operator FAST).
3. Engine ON/OFF Switch – ON position permits engine
starting, OFF position stops engine operations.
PAGE 18 —WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRIC MOTOR COMPONENTS
ELECTRIC MOTOR
Electric Motor Connection
For lubrication care and operation of the electric motor,
refer to your electric motor instruction booklet furnished
with the motor.
The electrical motors used on these mixers are equipped
with either a 3-prong (1Ø) or a 4-prong (3Ø) plug (Figure 7)
for connection to a power source. Reference Table 5. to
determine the required NEMA mating receptacle.
Protect the electric motor from dust as much as possible
and keep ventilating openings clean.
CAUTION
It is strongly recommended that all electrical
wiring be done by a licensed electrician. Pay
special attention to the nameplate on the electric
motor.Make certain that the voltage supplied to
the electric motor matches the required
operating voltage printed on the nameplate.
DO NOT spray water at any time on the electric motor.
DO NOT operate electric motor in an explosive
environment.
The electric motors (Figure 7) used on these mixers is
available in two types of configurations, 5 HP 1Ø @230
VAC or 5 HP 3Ø @230/460 VAC. Pay special attention to
the nameplate on the electric motor when supplying power
to the electric motor. Applying incorrect power to the motor
can severly damage the motor and may cause serious
bodily injury!
Table 5. Electric Motor Wiring Information
Electric Motor
Horsepower
Rating
230 VAC - 1Ø Phase
230/460 VAC - 3Ø Phase
NEMA Plug Connector
3-Prong
NEMA Plug Connector
4-Prong
L6-30P P/N 201794
L16-20P P/N 111012320
Always make certain that the correct voltage is being
supplied to the motor.The input voltage requirements can
be found on the electric motor's nameplate.
5 HP
NEMA Receptacle
Connector
3-Prong
L6-30R P/N TBD
NEMA Receptacle
Connector
4-Prong
L16-20R P/N 110012340
NEMA
L6 30P PLUG
230 VAC
NEMA
L16 20P PLUG
230/460 VAC
3Ø PHASE
1Ø PHASE
SINGLE OR THREE PHASE
ELECTRIC MOTOR
ON/OFF
SWITCH
NAMEPLATE
PIGTAIL END
ELECTRIC CABLE
BLACK
GREEN
WHITE
Figure 7. Electric Motor
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 19
Download from Www.Somanuals.com. All Manuals Search And Download.
PADDLE BLADE ADJUSTMENT (STEEL DRUM)
Adjust paddles as shown in Figure 8.
Figure 8. Paddle Blade Adjustment (Steel Drum)
PAGE 20 —WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
PADDLE BLADE ADJUSTMENT (POLY DRUM)
Adjust paddles as shown in Figure 9.
Figure 9. Paddle Blade Adjustment (Poly Drum)
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 21
Download from Www.Somanuals.com. All Manuals Search And Download.
INSPECTION
This section is intended to assist the operator with the
inspection of the hydraulic mixer. It is extremely important
that this section be read carefully before attempting to use
the mixer in the field.
Reference manufacturer engine manual for
specific servicing instructions.
DO NOT use your mixer until this section is thoroughly
understood.
BEFORE STARTING
1. Read all safety instructions at the beginning of
manual.
2. Clean the mixer, removing dirt and dust, particularly
the engine cooling air inlet, carburetor and air cleaner.
Figure 11. Engine Oil Dipstick (Removal)
3. Check the air filter for dirt and dust. If air filter is
dirty, replace air filter with a new one as required.
TABLE 6. OIL TYPE
4. Check carburetor for external dirt and dust. Clean with
dry compressed air.
Season
Summer
Spring/Fall
Winter
Temperature
25°C or Higher
25°C~10°C
Oil Type
SAE 10W-30
SAE 10W-30/20
SAE 10W-10
5. Check fastening nuts and bolts for tightness.
ENGINE OIL CHECK
0°C or Lower
1. To check the engine oil level, place the mixer on secure
level ground with the engine stopped.
FUEL CHECK
2. Remove the filler dipstick from the engine oil filler hole
(Figure 10) and wipe it clean.
DANGER — Explosive Fuel Hazards
If your mixer has a gasoline engine,
determine if the engine fuel is low. If fuel
is low, remove the fuel filler cap and fill it
with unleaded gasoline. Motor fuels are
highly flammable and can be dangerous if
mishandled. DO NOT smoke while refueling. DO NOT
attempt to refuel the mixer if the engine is hot! or
running.
CAUTION — Start/Stop Switch
Figure 10. Engine Oil Dipstick (Removal)
NEVER! disable or disconnect the start/stop switch. It
is provided for operator safety. Injury may result if it is
disabled, disconnected or improperly maintained.
3. Insert and remove the dipstick without screwing it into
the filler neck. Check the oil level shown on the dipstick.
4. If the oil level is low (Figure 11), fill to the edge of the
oil filler hole with the recommended oil type (Table 6).
Maximum oil capacity is 1.16 quarts (1.1 liters).
1. Remove the gasoline cap located on top of fuel tank.
2. Visually inspect to see if fuel level is low. If fuel is low,
replenish with unleaded fuel.
3. When refueling, be sure to use a strainer for filtration.
DO NOT top-off fuel.Wipe up any spilled fuel.
PAGE 22 —WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
INSPECTION
HYDRAULIC OIL
Check hydraulic oil sight gauge (Figure 12) to ensure that
hydraulic oil is at the midway level.
Figure 12. Hydraulic Oil Sight Gauge
HYDRAULIC HOSES
Figure 14. Grease Fittings (Dump Cylinder)
BLADE CHECK
Check hydraulic hoses to make sure they are not worn,
frayed or defective.
Check for worn or paddle blades. Make sure that all blades
are adjusted properly. See blade adjustment procedure in
this manual. Replace all defective or damaged blades
immediately.
GREASE FITTINGS (BEARINGS)
Check the zerk grease fittings (Figure 13) on the bearing
housings and dump support brackets at each end of the
mixing drum. These grease fittings lubricate the dumping
mechanism. If the dumping handle is stiff or hard to move
lubricate these fittings.
DUMP HANDLE (MANUAL DUMP MACHINES ONLY)
Before operating a manual dump mixer, ensure that the
dump handle has been placed in the operating position.
See Figure 15.
1. Remove and retain nuts (2) and bolts (2) that secure
dump handle to the drum in towing position.
2. Place dump handle in operating position and re-install
nuts and bolts to secure dump handle to drum.
Figure 13. Grease Fittings (Bearings)
GREASE FITTING (DUMP CYLINDER)
1. If your unit has hydraulic dump capability, check the
zerk grease fitting at the top of the dump cylinder
(Figure 14).This grease fitting lubricates the hydraulic
dumping mechanism.
Figure 15. Dump Handle
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 23
Download from Www.Somanuals.com. All Manuals Search And Download.
INITIAL START-UP (GASOLINE)
4.
Place the engine ON/OFF switch (Figure 19) in the ON
position position.
STARTINGTHE ENGINE
The following steps outline the procedure for starting the
engine. Depending on the type of engine employed in the
mixer the steps may vary slightly. If your mixer has an
electric motor disregard this section.
1. Place the fuel valve lever (Figure 16) in the ON position.
Figure 19. Engine ON/OFF Switch
5. Located on the engine cover is the engine start/stop
switch (Figure 20). Pull this switch outward to start the
engine.
START STOP
SWITCH
Figure 16. Fuel Shut-OFF Lever
2. To start a cold engine, move the choke lever (Figure
17) to the CLOSED position.
PULL OUT
TO START
OP
PUSH
ST
O
T
Figure 20. Main ON/OFF Switch
6. Pull the starter grip (Figure 21) lightly until you feel
resistance, then pull briskly. Return the starter grip
gently. Push the clutch lever forward, toward the tow
tongue end of the mixer. When engine starts, adjust
throttle lever so that paddle shaft inside mixer rotates
between 30-40 RPMs. The number of RPMs will vary
depending on engine type and load.
Figure 17. Choke Lever
3. Move the throttle lever (Figure 18) away from the slow
position, about 1/3 of the way toward the fast position.
Figure 18. Throttle lever Lever
Figure 21. Starter Grip
PAGE 24 —WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
INITIAL START-UP (ELECTRIC)/OPERATION
STARTINGTHE ELECTRIC MOTOR
1. Using an adequate size extension cord (Table 7),
connect one end of the extension cord to the plug on
the electric motor, connect the other end to the power
source. Make sure the motor is configured for the
proper operating voltage.
2. To start the electric motor, press the black ON/START
switch (Figure 22).
Figure 23. Hydraulic Paddle Lever
ON
OFF
5. Manual dump machines only: When mixing plaster or
mortar, the drum lock lever (Figure 24) should be in
the horizontal (down) position. (Does not apply to
hydraulic dump mixers.)
START
STOP
PRESS TO
START
Figure 22. Electric Motor On/OFF Switch (Start)
Table 7. Load Ampere (Current) Rating
(3Ø Extension)
Cord Length
ft (m)
0-2
2-5
5-7
7-10
10-12
12-15
15-20
12 ga
10 ft (3.0 m)
25 ft (7.6 m)
16 ga
16 ga
16 ga
16 ga
14 ga
16 ga
16 ga
16 ga
14 ga
14 ga
16 ga
16 ga
14 ga
12 ga
12 ga
16 ga
14 ga
12 ga
12 ga
10 ga
14 ga
14 ga
12 ga
14 ga
12 ga
50 ft (15.2 m)
100 ft (30.5 m)
150 ft (45.7 m)
200 ft (61.0 m)
Figure 24. Drum Lock Lever
Extension cords must be rated “HEAVY DUTY” or “EXTRA-HEAVY DUTY”
and must be a continuous length.
When the drum lock lever is placed
horizontally, the drum will be maintained in
the vertical position as the paddles rotate.
This condition does not apply to models that
have hydraulic dump capability.
MIXING
1. On the hydraulic valve, push lever inward (Figure 23)
for clockwise mixing rotation of blades.
2. The paddle shaft inside the drum should be rotating at
this time.
WARNING — Dump Handle Safety
3. Add a small amount water to the mixing drum.
ALWAYS stand clear of the dump
handle when the mixer is operational.
Any binding of material between the
mixer blades and the drum will cause
the drum handle to quickly move and
could cause severe bodily harm.
4. Lift the mixing bag compound onto the steel safety
grate over the bag cutter and let the contents fall into
the drum. Add more water if desired and mix compound
to desired consistency.
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 25
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
DUMPING (MANUAL)
DUMPING (HYDRAULIC)
1. Release drum lock lever by pushing lever into vertical
1. If operating a mixer with hydraulic dump capability, pull
hydraulic dump lever (Figure 27) outward to place drum
in dump position (Figure 28).
position (Figure 25).
Figure 25. Drum Lock Lever
2. Pull dump handle downward to discharge (empty) the
drum. Move dump handle upward to return it to vertical
position. (Figure 26).
Figure 27. Hydraulic Dump Lever
Figure 26. Manual Dump Handle
Figure 28. Hydraulic Dump
3. Drum lock lever automatically moves back to horizontal
position, locking the drum back into vertical position.
2. Push hydraulic dump lever inward to place drum back
in vertical position.
4. Inspect for proper functionality before starting the engine
or engaging blades. Any binding of material between the
mixing blades and drum will cause the handle to quickly
rotate if not in the “up and locked” position.
PAGE 26 —WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
SHUT-DOWN
STOPPINGTHE MIXER (GASOLINE ENGINE)
STOPPINGTHE MIXER (ELECTRIC MOTOR)
1. Push the start/stop switch (Figure 29) inward to stop
1. To stop the electric motor, press the red OFF/STOP
the engine.
switch (Figure 31).
ON
OFF
START
STOP
PRESS TO
STOP
Figure 31. Electric Motor On/OFF Switch (Stop)
Figure 29. Start/Stop Switch (Stop)
2. Disconnect the electric motor's extension cord from
its power source.
2. Place the fuel valve (Figure 30) lever to the OFF
position.
3. Clean mixer as referenced in the maintance section of
this manual.
Figure 30. Fuel Valve Lever (Off)
3. Clean mixer as referenced in the maintenance section
of this manual.
CAUTION —Start/Stop Switch
NEVER disable or disconnect the start/stop switch. It
is provided for operator safety. Serious Injury may
result if it is disabled, disconnected or improperly
maintained.
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 27
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE (ENGINE)
UseTable 8 as a general maintenance guideline when servicing your engine.For more detail engine maintenance information,
refer to the engine owner's manual supplied with your engine.
TABLE 8. ENGINE MAINTENANCE SCHEDULE
FIRST
EVERY
EVERY
EVERY
YEAR
OR
EVERY
2 YEARS
OR
MONTH 3 MONTHS 6 MONTHS
OR
DESCRIPTION (3)
OPERATION
BEFORE
OR
OR
10 HRS.
25 HRS.
50 HRS.
100 HRS.
200 HRS.
CHECK
CHANGE
CHECK
X
Engine Oil
X
X
X
X
Air Cleaner
All Nuts & Bolts
Spark Plug
CHANGE
X (1)
Re-tighten If
Necessary
CHECK-CLEAN
REPLACE
CHECK
X
X
X
Cooling Fins
Spark Arrester
Fuel Tank
CLEAN
X
X
CLEAN
Fuel Filter
CHECK
X
Idle Speed
CHECK-ADJUST
CHECK-ADJUST
CHECK
X (2)
Valve Clearance
Fuel lines
X (2)
Every 2 years (replace if necessary) (2)
(1) Service more frequently when used in DUSTY areas.
(2) These items should be serviced by your service dealer, unless you have the proper tools and are mechanically
proficient. Refer to the HONDA Shop Manual for service procedures.
(3) For commercial use, log hours of operation to determine proper maintenance intervals.
PAGE 28 —WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE (ENGINE)
3. Replace engine oil with recommended type oil as listed
in Table 6. For engine oil capacity, see Table 2 (engine
specifications). DO NOT overfill.
MAINTENANCE
Perform the scheduled maintenance procedures as defined
by Table 8 and below:
4. Install drain bolt with sealing washer and tighten
securely.
Daily
■
Thoroughly remove dirt and oil from the engine and
control area. Clean or replace the air cleaner elements
as necessary. Check and retighten all fasteners as
necessary. Check the gearbox for oil leaks. Repair or
replace as needed.
ENGINE AIR CLEANER
1. Remove the air cleaner cover and foam filter element
as shown in Figure 34.
2. Tap the paper filter element (Figure 34) several times
on a hard surface to remove dirt, or blow compressed
air [not exceeding 30 psi (207 kPa, 2.1 kgf/cm2)] through
the filter element from the air cleaner case side. NEVER
brush off dirt. Brushing will force dirt into the fibers.
Replace the paper filter element if it is excessively
dirty.
Weekly
■
Remove the fuel filter cap and clean the inside of the
fuel tank.
■
■
Remove or clean the filter at the bottom of the tank.
Remove and clean the spark plug (Figure 32), then adjust
the spark gap to 0.024 ~0.028 inch (0.6~0.7 mm). This
unit has electronic ignition, which requires no
adjustments.
3. Clean foam element in warm, soapy water or
nonflammable solvent. Rinse and dry thoroughly. Dip
the element in clean engine oil and completely squeeze
out the excess oil from the element before installing.
DANGER — Explosive Hazard
DO NOT use gasoline as a cleaning solvent to avoid
creating the risk of fire or an explosion.
Figure 32. Spark Plug Gap
ENGINE OIL
1. Drain the engine oil when the oil is warm as shown in
Figure 33.
2. Remove the oil drain bolt and sealing washer and allow
the oil to drain into a suitable container.
Figure 33. Engine Oil (Draining)
Figure 34. Engine Air Cleaner
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 29
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE (MIXER)
BALL SOCKET AND CLAMP FACE MAINTENANCE
DRUM HEAD SEALS
There is 1 set of drum head seals (Figure 35) that will require
lubrication. Lubricate the grease fitting for each drum seal
after each use using any grade lithium base grease. Apply
grease until visible inside of mixing drum (over grease).
This will purge seal system of contamination.
1. If the towing vechicle is equipped with a ball socket,
smear socket periodically with multi-purpose grease.
This will keep the ball socket well lubricated.
2. Periodically oil pivot points and clamp face surfaces
of coupler with SAE 30 WT. motor oil.
3. When parking or storing your mixer. Keep the coupler
off the ground so dirt will not build up in the ball socket.
GREASE FITTING
AND CAP
GREASE FITTING DRUM HEAD
AND CAP
SEALS
HYDRAULIC OIL FILTER
Replace hydraulic oil filter (Figure 37) every 500 hours.
Hydraulic tank capacity is 12 gallons (45 liters). Refill with
any of the following hydraulic oil types. Shell Tellius 68,
Mobil DFE26 or Texaco Rand HDC.
Figure 35. Grease Fittings (Drum Head Seals)
DRUM BEARING BRACKET LUBRICATION
There is 1 set of drum bearing brackets (Figure 36) that will
require lubrication. These brackets are intended to make
the drum rotate freely. Lubricate the grease fitting for each
drum bearing bracket every month or when the drum
becomes difficult to position using multi-purpose grade
grease.
Figure 37. Hydraulic Oil Filter
WHEEL BEARINGS
GREASE FITTING
AND CAP
1. After every 3 months of operation, remove the hub
dust cap and inspect the wheel bearings (Figure 38).
Once a year, or when required, disassemble the wheel
hubs remove the old grease and repack the bearings
forcing grease between rollers, cone and cage with a
good grade of high speed wheel bearing grease (never
use grease heavier than 265 A.S.T.M. penetration (“No.
2.”)
GREASE FITTING
AND CAP
DRUM BEARING
BRACKET
Figure 36. Grease Fittings (Dumping Mechanism)
CAUTION — Lubricate Grease Fittings
Failure to lubricate the drum bearing grease fittings
eriodically will cause the dumping mechanism to stiffen,
making the mixing drum hard to dump.
Figure 38. Wheel Hub and Bearings
PAGE 30 —WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE (MIXER)
TIRES/WHEELS/LUG NUTS
LUG NUTTORQUE REQUIREMENTS
Tires and wheels are a very important and critical
components of the trailer. When specifying or replacing
the trailer wheels it is important the wheels, tires, and axle
are properly matched.
It is extremely important to apply and maintain proper wheel
mounting torque. Be sure to use only the fasteners matched
to the cone angle of the wheel. Proper procedure for
attachment of the wheels is as follows:
1. Start all wheel lug nuts by hand.
WARNING — Damaged Wheels
2. Torque all lug nuts in sequence. See Figure 39. DO
NOT torque the wheel lug nuts all the way down.Tighten
each lug nut in 3 separate passes as defined by Table
10.
DO NOT attempt to repair or modify a
wheel. DO NOT install an inter-tube
to correct a leak through the rim. If
the rim is cracked, the air pressure in
the inter-tube may cause pieces of the
rim to explode (break-off) with great force and can cause
serious eye or bodily injury.
TABLE 10. TIRE TORQUE REQUIREMENTS
First Pass
FT-LBS
Second Pass
FT-LBS
Third Pass
FT-LBS
Wheel Size
TIRESWEAR/INFLATION
12"
13"
14"
15"
16"
20-25
20-25
20-25
20-25
20-25
35-40
35-40
50-60
50-60
50-60
50-65
50-65
Tire inflation pressure is the most important factor in tire
life. Pressure should be checked cold before operation.
DO NOT bleed air from tires when they are hot. Check
inflation pressure weekly during use to insure the maximum
tire life and tread wear.
90-120
90-120
90-120
WARNING — Eyesight Hazard
ALWAYS wear safety glasses when
removing or installing force fitted
parts. Failure to comply may result in
serious injury.
NEVER! use an pneumatic air gun to tighten
wheel lug nuts.
Table 9 (Tire Wear Troubleshooting) will help pinpoint the
causes and solutions of tire wear problems.
TABLE 9.TIRE WEARTROUBLESHOOTING
CAUSE
WEAR PATTERN
SOLUTION
Adjust pressure to
particular load per
tire manufacturer.
Over Inflation
Center Wear
Adjust pressure to
particular load per
tire manufacturer.
Edge Wear
Side Wear
Under Inflation
Loss of chamber Make sure load does
or overloading.
not exceed axle rating.
Align wheels.
Align wheels.
Incorrect toe-in
Out-of balance
Toe Wear
Cupping
Check bearing adjust-
ment and balance tires.
Avoid sudden stops
when possible and
adjust brakes.
Wheel lockup &
tire skidding.
Flat Spots
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 31
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE (MIXER)
3. After first road use, retorque all lug nuts in sequence.
Check all wheel lug nuts periodically.
SUSPENSION
The suspension type axle and associated hardware (Figure
40) should be periodically inspected for signs of excessive
wear, elongation of bolt holes, and loosening of fasteners.
Replace all damaged parts immediately.
Figure 40. Axle Support Components
MIXER CLEANING
It is important that the drum interior is free of dried material.
Obstructions can cause the paddle blades to lock against
the drum resulting in sudden dump handle movement.
1. Stop the engine. Push the engine “Kill” button to the
“OFF” position.
2. Place the hydraulic paddle lever (Figure 5) in "neutral"
position do disengage.
3. ALWAYS disconnect the spark plug wire (gasoline
engines) before cleaning the inside of the drum. If mixer
is equipped with an electric motor remove power cord
from AC power source. In addition make sure the
clutch engagement lever is disengaged.
4. Place “Do Not Operate” tag on mixer.
5. Make sure the rear section of safety grate is connected
to the mixing drum.
6. At the end of each day’s operation, place mixer drum
in an upright position and spray inside of tub
immediately with water to prevent lumps of dried mortar
or plaster from forming and contamination of future
batches, DO NOT allow a buildup of materials to form
on the blades or anywhere inside the drum.
Figure 39. Wheel Lug Nuts Tightening Sequence
7. Rotate mixer to dump position and remove debris.
8. Thoroughly clean the entire mixer, wheels, cabinet
and frame.
PAGE 32 —WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE (MIXER)/STORAGE
9. NEVER! pour or spray water over the engine or electric
motor (Figure 41).
MIXER STORAGE
For storage of the mixer for over 30 days, the following is
recommended:
Drain the fuel tank completely, or add STA-BIL to the
fuel.
Run the engine until the fuel is completely
consumed.
Completely drain used oil from the engine crankcase
and fill with fresh clean oil, then follow the procedures
described in the engine manual for engine storage.
Figure 41. No Spraying of Water
10. When cleaning of the entire mixer is done, return
mixing drum to an upright position.
Clean the entire mixer and engine compartment.
Place the mixing drum in the down position (mouth facing
downward).
WARNING — Keep Hands Clear of Drum
When rotating the mixing drum from the dump position
to the upright position, keep hands clear of safety
grate. The possibility exists of hands or fingers being
crushed (Figure 42).
Cover the mixer and place it a clean dry area, that is
protected from harsh elements.
Figure 42. Safety Grate (Crush Hazard)
WARNING — Disengaged Drum Lock
DO NOT start engine or engage paddle arms when drum
lock lever is not engaged.
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 33
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING (ENGINE)
Practically all breakdowns can be prevented by proper handling and maintenance inspections, but in the event of a
breakdown, please take a remedial action following the diagnosis based on the Engine, Mixer and Electric Motor
Troubleshooting (Tables 11,12, and 13) information shown below and on the proceeding pages. If the problem cannot be
remedied, please leave the unit just as it is and consult or company's service department.
TABLE 11. ENGINE TROUBLESHOOTING
SYMPTOM
POSSIBLE PROBLEM
SOLUTION
Inspect carburetor to see if fuel
is reaching it?
Check fuel line
No Fuel?
Add Fuel
Water in fuel tank?
Fuel filter clogged?
Stuck carburetor?
Spark plug is red?
Flush or replace fuel tank.
Replace fuel filter
Check float mechanism.
Poor starting
Spark plug is fouled. Check tranistor ignition unit.
Insufficient compression, injected air leaking. Carburetor jets are
clogged (overflow).
Spark plug is blue-white?
No spark present at tip of spark
plug?
Tranistor ignition unit broken, high voltage cord cracked or broken.
Start/Stop switch broken. Replace spark plug if fouled.
No oil?
Add oil as required.
Oil pressure alarm lamp blinks
upon starting?
Check Automatic shutdown circuit "oil sensor".
Replace cylinder and piston and if necessary axel joint.
Tighten cylinder head connecting bolts.
Engine will not turn over?
Cylinder head connecting bolts
loose?
Cylinder head gasket damaged? Replace cylinder head gasket.
Insufficient power output "no
compression"
Malfunction of valve seat?
Spark plug is loose?
Worn piston rings?
Re-seat valves.
Replace spark plug.
Replace piston rings.
Malfunction in air-cleaner
system, air filter clogged?
Clean or replace air filter.
Air leaking in from interface
between carburetor and cylinder
head?
Tighten bolts between carburetor and cylinder head. Replace
cylinder head gasket.
Insufficient power output
"compression"
Clean or replace fuel filter.
Clean or replace carburetor.
Check carburetor float.
Malfunction in fuel system?
PAGE 34 —WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING (ENGINE)
TABLE 11. ENGINE TROUBLESHOOTING (CONTINUED)
SYMPTOM
POSSIBLE PROBLEM
Malfunction in cooling fan?
Air in-take filter clogged?
SOLUTION
Check or replace cooling fan.
Insufficient power output
"compression" and overheats
Clean or replace air in-take filter.
Over accumulation of exhaust
products?
Clean and check valves.
Check muffler, replace if necessary.
Burns to much fuel
Wrong spark plug?
Replace spark plug with manufactures suggested type spark plug.
Replace lubricating oil with correct viscosity.
Lubricating oil is wrong
viscosity?
Exhaust color is continiously
"WHITE"
Worn rings?
Replace rings
Air cleanner clogged?
Clean or replace air cleaner.
Choke valve has not been set to Adjust choke valve to the correct position.
the correct position?
Exhaust color is continiously
"BLACK"
Carburetor defective, seal on
carburetor broken?
Replace carburetor or seal.
Adjust carburetor.
Poor carburetor adjustment
"engine runs too rich?
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 35
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING (MIXER/ELECTRIC MOTOR)
TABLE 12. MIXER TROUBLESHOOTING
SYMPTOM
POSSIBLE PROBLEM
SOLUTION
Material load too heavy,
exceeding mixer capability?
Reduce amount of material being mixed.
Object stuck inside mixing
drum, jamming paddle
rotation?
Stop engine. Empty out drum contents. Remove
obstruction.
Incorrect relief valve
pressure?
Inspect for proper 1750 PSI relief pressure.
Proper RPM 3600.
Blades will not rotate.
Check engine speed.
Defective hydraulic motor or
pump?
Contact MQ Technical Services.
Slow hydraulic cylinder
dumping?
Defective cylinder seal.
Replace seals.
Material leaking from drum Worn or defective paddle
ends.
shaft seals?
Defective or worn drum
support brackets?
Apply grease to bracket or replace.
Drum difficult to discharge
(tilt)
Adjust blades until they almost touch side walls of
drum.
Blades adjusted too tight.
TABLE 13. ELECTRIC MOTOR TROUBLESHOOTING
SYMPTOM
POSSIBLE PROBLEM
No voltage to motor?
SOLUTION
Check power source.
Defective extension cord?
Replace extension cord.
Replace switch.
Blades will not rotate.
Defective motor ON/OFF switch?
Defective motor windings?
Repair windings or replace windings.
PAGE 36 —WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
WIRING DIAGRAM (ELECTRIC MOTOR)
WHITE/NEUTRAL
X
230 VAC 1Ø
2-POLE/3-WIRE
GROUNDING
Y
BLACK/LINE
G
GREEN/GROUND
L6-30P
TWIST-LOCK
SINGLE OR THREE PHASE
ELECTRIC MOTOR
L6-30P/L1620P
TWIST-LOCK
PIGTAIL END
ELECTRIC CABLE
WHITE/NEUTRAL
X
460 VAC 3Ø
3-POLE/4-WIRE
GROUNDING
Y
BLACK/LINE
G
GREEN/GROUND
Z
RED/LINE
L16-20P
TWIST-LOCK
Figure 43. Electric Motor Wiring Diagram
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 37
Download from Www.Somanuals.com. All Manuals Search And Download.
HYDRAULIC SYSTEM DIAGRAM
HYDRAULIC SYSTEM DIAGRAM
HYDRAULIC
DUMP
FORWARD/REVERSE
GEAR
PUMP
POWER
RELIEF
VALVE
1750 PSI
RETURN
FILTER
SUCTION
STRAINER
BYPASS
25 PSI
2
1
HYD
MOTOR
TANK
TANK
RELIEF
VALVE
CYLINDER
1750 PSI
SHOWN WITH OPTIONAL HYDRAULIC DUMP
Figure 44. Hydraulic System Diagram
PAGE 38 —WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 39
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLANATION OF CODE IN REMARKS COLUMN
The following section explains the different symbols and
QTY. Column
remarks used in the Parts section of this manual. Use the
help numbers found on the back page of the manual if there
are any questions.
Numbers Used — Item quantity can be indicated by a
number, a blank entry, or A/R.
A/R (As Required) is generally used for hoses or other
parts that are sold in bulk and cut to length.
NOTICE
The contents and part numbers listed in the parts
section are subject to change without notice.Multiquip
does not guarantee the availability of the parts listed.
A blank entry generally indicates that the item is not sold
separately.Other entries will be clarified in the“Remarks”
Column.
SAMPLE PARTS LIST
REMARKS Column
NO. PART NO. PART NAME
QTY. REMARKS
Some of the most common notes found in the “Remarks”
Column are listed below. Other additional notes needed
to describe the item can also be shown.
1
12345
BOLT......................1 .....INCLUDES ITEMS W/%
WASHER, 1/4 IN............NOT SOLD SEPARATELY
WASHER, 3/8 IN....1 .....MQ-45T ONLY
HOSE ..................A/R ...MAKE LOCALLY
BEARING ..............1 .....S/N 2345B AND ABOVE
2%
2% 12347
12348
12349
3
Assembly/Kit — All items on the parts list with the
same unique symbol will be included when this item is
purchased.
4
NO. Column
Indicated by:
Unique Symbols — All items with same unique
symbol
“INCLUDES ITEMS W/(unique symbol)”
(@, #, +, %, or >) in the number column belong to the
same assembly or kit, which is indicated by a note in the
“Remarks” column.
Serial Number Break — Used to list an effective serial
number range where a particular part is used.
Indicated by:
Duplicate Item Numbers — Duplicate numbers indicate
multiple part numbers, which are in effect for the same
general item, such as different size saw blade guards in
use or a part that has been updated on newer versions
of the same machine.
“S/N XXXXX AND BELOW”
“S/N XXXX AND ABOVE”
“S/N XXXX TO S/N XXX”
Specific Model Number Use — Indicates that the part
is used only with the specific model number or model
number variant listed. It can also be used to show a
part is NOT used on a specific model or model number
variant.
NOTICE
When ordering a part that has more than one item
number listed, check the remarks column for help in
determining the proper part to order.
Indicated by:
“XXXXX ONLY”
“NOT USED ON XXXX”
PART NO. Column
Numbers Used — Part numbers can be indicated by a
number, a blank entry, or TBD.
“Make/Obtain Locally” — Indicates that the part can
be purchased at any hardware shop or made out of
available items.Examples include battery cables, shims,
and certain washers and nuts.
TBD (To Be Determined) is generally used to show a
part that has not been assigned a formal part number
at the time of publication.
“Not Sold Separately”— Indicates that an item cannot
be purchased as a separate item and is either part of an
assembly/kit that can be purchased, or is not available
for sale through Multiquip.
A blank entry generally indicates that the item is not sold
separately or is not sold by Multiquip. Other entries will
be clarified in the “Remarks” Column.
PAGE 40 —WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
SUGGESTED SPARE PARTS
WM120PS 1TO 3 UNITS
WM120PS 5TO 10 UNITS
Qty.
P/N
Description
Qty.
P/N
Description
6 ............ 491010 ............ RUBBER LATCH ASSY.
10 .......... 491010 ............ RUBBER LATCH ASSY.
1 ............ EM200293A .... PADDLE ARM TOW SIDE
1 ............ EM200294A .... PADDLE ARM CENTER TOW SIDE
1 ............ EM200295A .... PADDLE ARM CENTER ENGINE SIDE
1 ............ EM200296A .... PADDLE ARM ENGINE SIDE
3 ............ EM200863 ...... RUBBER BLADE KIT (STEEL DRUM)
3 ............ EM204625 ...... RUBBER BLADE KIT (PLASTIC DRUM)
4 ............ EM200297 ...... U-BOLT
2 ............ EM200293A .... PADDLE ARM TOW SIDE
2 ............ EM200294A .... PADDLE ARM CENTER TOW SIDE
2 ............ EM200295A .... PADDLE ARM CENTER ENGINE SIDE
2 ............ EM200296A .... PADDLE ARM ENGINE SIDE
6 ............ EM200863 ...... RUBBER BLADE KIT (STEEL DRUM)
3 ............ EM204625 ...... RUBBER BLADE KIT (PLASTIC DRUM)
16 .......... EM200297 ...... U-BOLT
2 ............ 3530................ PADDLE SHAFT, SEAL KIT
2 ............ EM902153 ...... BEARING, PADDLE SHAFT
4 ............ 3530................ PADDLE SHAFT, SEAL KIT
4 ............ EM902153 ...... BEARING, PADDLE SHAFT
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 41
Download from Www.Somanuals.com. All Manuals Search And Download.
NAMEPLATE AND DECALS
PAGE 42 —WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
NAMEPLATE AND DECALS
NO.
1
2
3
4
5
6
7
8
PART NO.
DCL151
EM948630
DCL160A
515275
504713
35137
504714
513479
DCL335
DCL280
13238
PART NAME
DECAL,TOWING INSTRUCTIONS
DECAL, PUSH TO STOP
QTY.
REMARKS
2
1
2
3
1
1
3
1
1
1
1
1
DECAL, CRUSH WARNING
DECAL, WHITEMAN LOGO (SMALL)
DECAL, SAFETY INSTRUCTIONS
DECAL, WARNING READ
DECAL, WHITEMAN LOGO (LARGE)
DECAL, WARNING SAFETY GRATE
DECAL, CRUSH WARNING SAFETY GRATE
DECAL, WARNING DUMP HANDLE
DECAL, CONTROLS, MOLD-IN
DECAL, POWDER COATED
9
10
11
12
13
13118
NAMEPLATE........................................................ 1 ......... CONTACT PARTS DEPT.
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 43
Download from Www.Somanuals.com. All Manuals Search And Download.
PADDLE BLADES ASSY.
ENGINE END
6
5
2
CENTER
ENGINE END
7
9
CENTER
TOW END
7
8
2
8
5
3
18
16
10
19
7
17
WIPER
AND
SCRAPPER
HARDWARE
KIT
2
10
S
I
D
E
S
C
R
R
PO
L
A
P
E
R
Y
13
O
R
U
B
R
E
TOW
END
15
12
11
14
PAGE 44 —WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
PADDLE BLADES ASSY.
NO.
2
3
5
6
PART NO.
492584
EM200295A
EM200292
EM200293A
6109170
PART NAME
QTY.
8
1
8
1
REMARKS
NUT, LOCK 1/2"
PADDLE ARM, CENTER TOW END
INSERT, PADDLE ARM
PADDLE ARM, TOW END
WASHER, FLAT 1/2"
7
8
8
9
10
EM200297
EM200294A
492366
EM923023
13352
EM200212
EM203432
2105164
EM923343
EM200296A
EM203433
EM507518
EM200213
EM200863
U-BOLT, END PADDLES
PADDLE ARM, CENTER ENGINE END
SCREW, HHC 5/16-18 X 1-1/2 G5
WASHER, FLAT 5/16" STEEL
WIPER, SIDE (PLASTIC) ............................................... 4............ PLASTIC DRUM
WIPER, SIDE (RUBBER) ............................................... 4............ STEEL DRUM
SCRAPPER, SIDE.......................................................... 4............ PLASTIC/STEEL DRUMS
NUT, HEX 5/16"
WASHER, LOCK 5/16"
PADDLE ARM, ENGINE END
SCRAPPER, END ........................................................... 2............ PLASTIC/STEEL DRUMS
BLADE, PLASTIC (END) ................................................ 2............ PLASTIC DRUM
BLADE, RUBBER (END) ................................................. 2............ STEEL DRUM
KIT, RUBBER BLADES, SCRAPERS & HARDWARE .... 1............ INCLUDES ITEMS W/
....................................................................................................... STEEL DRUM ONLY
4
1
14
28
#
#
*
11
*
12
12
13
14
15
16
17
18
18
19
#
*
*
*
*
#
#
#
14
14
1
*
#
*
*
#
19
EM204625
KIT, PLASTIC BLADES, SCRAPERS & HARDWARE .... 1............ INCLUDES ITEMS W/
....................................................................................................... PLASTIC DRUM ONLY
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 45
Download from Www.Somanuals.com. All Manuals Search And Download.
PLASTIC MIXING DRUM ASSY.
PAGE 46 —WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
PLASTIC MIXING DRUM ASSY.
NO
1#
2#
3#
4#
5#
6#
7#
8#
PART NO
3309
EM963057
13270
EM969013
6109170
504943
3006
507719
511910
EM963692
EM923025
13209
491008
EM916019
492581
EM621
EM963105
10176
13228
3327
511495
511526
509000
3047
13286
EM963610
3485
3382
2219
PART NAME
QTY.
REMARKS
GRATE, MOVABLE
HHCS 3/8 X 1-1/2"
GRATE, STATIONARY
NUT, NYLOC 3/8-16
1
6
1
8
WASHER, FLAT 1/2" ..........................................2............ MANUAL DUMP ONLY
SCREW, FLATHEAD 3/8" NC X 2
SUPPORT DISK
BEARING HOUSING
FHCS 1/4" NC X 1-1/4" G5
HHCS 1/2-13" X 1-1/2" G5 .................................2............ MANUAL DUMP ONLY
WASHER, FLAT 3/8"
REAR DRUM SUPPORT
CAP, GREASE FITTING
GREASE FITTING
LOCK NUT, NYLON 1/4-20
WASHER, FLAT 1/2" SPECIAL
SCREW, HHCS 1/2" NC X 2" G5 .......................4............ REPLACES EM492396
NUT, LOCK 1/2"-13 ............................................2............ MANUAL DUMP ONLY
PIN, DUMP CYLINDER
CYLINDER, DUMP
LOCK NUT 1" NC
SCREW HHCS 1" NC X 8
COTTER PIN 3/16" X 2"
SPACER, 2" X 1-1/8 X 1/4" L
SPACER, HYDRAULIC CYLINDER
HHCS 3/8" NC X 1-1/4" G8
DRUM SUPPORT
LATCH, TUB STAY
PIN, COTTER 1/8" X 1-1/2"
CAP, DUST
DUMP BEARING HOUS. BRACKET REAR
DUMP BEARING HOUS. BRACKET FRONT
MANUAL DUMP HANDLE..................................1............ MANUAL DUMP ONLY.DO NOT USE
.......................................................................................... ON HYDRAULIC DUMP MACHINE.
8
2
2
8
9#
10#
11#
12#
13#
14#
15#
16#
17#
18#
19
20
21
22
23
2
1
4
4
8
4
1
1
1
1
1
2
1
2
1
1
1
1
1
1
24
25
26#
27#
28#
29#
30#
31#
32#
33
3249
13218
3500
EM201537
34#
35#
36#
37#
38#
39#
40#
41
3042
MIXER DRUM, PLASTIC, BARE
PIN, HITCH CLIP
WASHER, FLAT 16 MM ZINC ............................1............ REPLACES 492602
BAR, GRATE LATCH
HHCS 1/2"-13 X 1-1/2"
NUT, LOCK 1/2"
WASHER, FLAT SAE 3/4"
DRUM AND SHAFT ASSY. MAN./HYD. DUMP ..1............ INCLUDES ITEMS W/#
1
1
925191
0401450160
511493
EM963692
492584
8151
1
1
7
1
512181
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 47
Download from Www.Somanuals.com. All Manuals Search And Download.
STEEL DRUM ASSY. (MANUAL)
PAGE 48 —WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
STEEL DRUM ASSY. (MANUAL)
NO
1#
2#
3#
4#
5#
6#
7#
8#
PART NO
EM203449
7170
6109170
13276
EM969013
EM621
491008
PART NAME
GRATE, MOVABLE
5/32" 3-5/16"
WASHER, FLAT 1/2"
BAR, GRATE LATCH
NUT, NYLOC 3/8"
WASHER, FLAT 1/2" SPECIAL
CAP, GREASE FITTING
GREASE FITTING
QTY.
REMARKS
1
2
3
1
8
4
4
4
EM916019
EM963105
13260
9#
SCREW, HHCS 1/2" NC X 2" G5 ............... 4........... REPLACES EM492396
FRONT DUMP SUPPORT BRACKET
CAP, DUST
10#
11#
12#
13#
14#
15#
16#
17#
18#
19#
20
1
1
8
2
1
1
1
1
7
1
1
3249
EM963610
EM924015
3291
516457
13259
EM963692
492584
512245
HHCS 3/8" NC X 1-1/4" G8
PIN, COTTER 3/16" X 1
BEARING HOUSING FRONT
BEARING HOUSING, REAR
REAR DUMP SUPPORT BRACKET
HHCS 1/2"-13 X 1-1/2"
NUT, LOCK 1/2"
STEEL DRUM, MANUAL
MANUAL DUMP HANDLE
EM201537
21
512180
DRUM AND SHAFT ASSY. MANUAL ......... 1........... INCLUDES ITEMS W/#
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 49
Download from Www.Somanuals.com. All Manuals Search And Download.
STEEL DRUM ASSY. (HYDRAULIC)
2
1
3
2
7
3
9
8
4
16
17
6
18
23
25
25
26
REAR
25
12
19
15
20
23
FRONT
7
21
5
24
DUMP
7
22
8
8
HYDRAULIC
9
11
14
10
27
6
25
3
24
NOTES:
COMPLETE DRUM ASSEMBLY, ITEM 27 INCLUDES
ITEMS WITHIN DASHED LINE. ALSO INCLUDED ARE
PADDLE SHAFT AND PADDLE ARMS. SEE PADDLE
PART OF FRAME
1
SHAFT AND PADDLE ARM ASSEMBLIES IN THIS MANUAL.
PAGE 50 —WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
STEEL DRUM ASSY. (HYDRAULIC)
NO
1#
2#
3#
4#
5#
6#
7#
8#
PART NO
EM203449
7170
6109170
13276
EM969013
EM621
491008
EM916019
EM963105
13260
PART NAME
MOVEABLE GRATE
PIN, HITCH CLIP 5/32" 3-5/16"
WASHER, FLAT 1/2"
BAR, GRATE
QTY. REMARKS
1
2
3
1
4
4
4
4
NUT, NYLOC 3/8"
WASHER, FLAT 1/2" SPECIAL
CAP, GREASE FITTING
GREASE FITTING
SCREW, HHCS 1/2" NC X 2" G5 ................... 4....... REPLACES EM492396
FRONT DUMP SUPPORT BRACKET
CAP, DUST
HHCS 3/8" NC X 1-1/4" G8
PIN, COTTER 3/16" X 1
BEARING HOUSING FRONT
9#
10#
11#
12#
13#
14#
15#
15#
16#
17
1
1
4
2
1
3249
EM963610
EM924015
3291
516457
511852
13259
509000
13228
3327
BEARING HOUSING, REAR (6 HOLE) ......... 1....... EFFECTIVE S/N K-25 - NOV 2005
BEARING HOUSING, REAR (4 HOLE)
REAR DUMP SUPPORT BRACKET
COTTER PIN 3/16" X 2"
PIN, DUMP CYLINDER
CYLINDER, DUMP
LOCK NUT 1" NC
1
1
1
1
1
1
18
19
20
511495
21
22
23
24#
25#
26#
27
13286
511526
3047
EM963692
492584
516535
511173
SPACER, LOWER HYDRAULIC CYLINDER 1
SCREW HHCS 1" NC X 8
SPACER, 2" X 1-1/8 X 1/4" L
HHCS 1/2"-13 X 1-1/2"
NUT, LOCK 1/2"
1
2
7
11
1
STEEL DRUM, HYDRAULIC
DRUM AND SHAFT ASSY. HYDRAULIC ....... 1....... INCLUDES ITEMS W/#
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 51
Download from Www.Somanuals.com. All Manuals Search And Download.
PADDLE SHAFT ASSY. (PLASTIC/STEEL)
20
2
15
1
OLD
STYLE
1
PA
DD
SH
A
10
LE
FT
K
IT
5
11
8
2
6
16
3
19
7
9
4
PADDLE
SHAFT
SEAL KIT
TOW
END
16A
17
18
15A
3
ENGINE
END
7
4
3
14
13
2
12
6
5
NOTES:
OLD STYLE PADDLE SHAFTS P/N 13257 (STEEL DRUM),
P/N13282 (PLASTIC DRUM) NO LONGER AVAILABLE. SEE
NOTE 2 WHEN RE-ORDERING PADDLE SHAFTS.
1
1
PADDLE SHAFT KITS P/N 514234K (PLASTIC DRUM), P/N
514233K (STEEL DRUM) INCLUDES ITEMS 15A, 16A, 17 AND 18.
2
3
FOR PLASTIC DRUM USE PADDLE SHAFT P/N 514234 , FOR
STEEL DRUM USE PADDLE SHAFT P/N 514233.
PAGE 52 —WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
PADDLE SHAFT ASSY. (PLASTIC/STEEL)
NO
1
2#
3#
4
PART NO
3061
3494
3019
3024
PART NAME
QTY.
14
2
REMARKS
SPACER, THIN SEAL
OUTER SEAL, URETHANE 1-1/4 OD
INNER SEAL 1-1/8"
SPRING
4
2
5
6
7
8
13002
EM902153
13274
3347
13108
10176
3215
3047
8164
EM924006
SEAL, BEARING 1-1/2"
BEARING
SPACER
NUT, SPECIAL 1-1/2"-12
WASHER, FLAT USS 1-1/8"
NUT, NYLOC 1/2-13 ...................................... 1 ........... OCTOBER 2002 AND BELOW
HHCS 1/2-13 X 3.1/2" ................................... 1 ........... OCTOBER 2002 AND BELOW
SPACER, 2 X 1-1/8" X1/4" L
NUT, SLOTTED HEX JAM 1-20
PIN, COTTER 1/8 X 3/4"
PADDLE SHAFT (PLASTIC) ......................... 1 ........... NOT AVAILABLE, ORDER ITEM 20
PADDLE SHAFT (STEEL) ............................ 1 ........... NOT AVAILABLE, ORDER ITEM 20
PADDLE SHAFT (STEEL)
2
2
2
1
9
1
10
11
12
13
14
15
15
15A%
15A
16
16A%
17%
1
1
1
514233
514234
13156
514235
EM502727
0857
3530
514234K
514233K
1
1
PADDLE SHAFT (PLASTIC)
*
COUPLER, PIN STYLE ................................ 1 ........... OCTOBER 2002 AND BELOW
COUPLER, KEY STYLE............................... 1 ........... NOVEMBER 2002 AND ABOVE
KEY, SQUARE 5/16 X 1-3/8" ........................ 1 ........... NOVEMBER 2002 AND ABOVE
SCREW, SHS 5/16-24 X 1/2"........................ 1 ........... NOVEMBER 2002 AND ABOVE
KIT, SEAL, PADDLE SHAFT ........................ 1 ........... INCLUDES ITEMS W/#
KIT, PADDLE SHAFT (PLASTIC).................. 1 ........... INCLUDES ITEMS W/%
*
*
18%
*
19
20
20
KIT, PADDLE SHAFT (STEEL) ..................... 1 ........... INCLUDES ITEMS W/
*
EFFECTIVE NOVEMBER 2002- THE PADDLE SHAFT
CONNECTOR PIN HAS BEEN DISCONTIUED.THE COUPLER
IS NOW KEYEDTOTHE PADDLE SHAFT.
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 53
Download from Www.Somanuals.com. All Manuals Search And Download.
HYDRAULIC ASSY.
PAGE 54 —WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
HYDRAULIC ASSY.
NO.
2
4
PART NO.
492356
2101402
EM969013
3019092
492584
13147
13153
13196
13210
13213
EM25459
511847
511509
13219
13220
511691
510263
13225
13243
13380
EM963105
16587
3322
34570
506207
18052
3353
3365
3367
511847
3462
8051
506094
3369
PART NAME
BOLT 1/4" X 3/4"
QTY.
2
REMARKS
WASHER, SPRING 1/4".......................................... 2................ REPLACES 492622
NUT, NYLOCK .........................................................1................ REPLACES 492583
WASHER 3/8" FLAT ................................................2................ REPLACES 492598
8
10
12
14
16
18
20
22
24
25
26
28
30
32
33
34
36
40
42
44
46
48
50
52
54
56
58
61
62
64
66
74
78
80
82
84
86
86
88
90
92
96
NUT, LOCK 1/2"
4
1
2
1
1
2
1
1
1
1
1
1
1
2
1
2
ARM, MOTORTORQUE
CAP, SPRING MOUNT
HOSE, PUMP OUTPUT 21"
STRAINER, IN LINE
SPRING, DIE
ELBOW 3/4"-90
FITTING
BOLT, 3/8" NC X 6" G5
FITTING 90 3/4 MP X 3/4 MP
FITTING, STR 12BARB X 3/4MP
FITTING, STR
FITTING, 90DEG STRAIGHT ELBOW
HANDLE, DRIVE VALVE CONTROL
HOSE W/ 90 DEG FITTING
HOSE, 3/4 ID X 18-1/2
HEX BOLT 1/2"-13 X 2" .......................................... 4................ REPLACES 492396
FITTING, STR 10MJ-8MO
FITTING, 90 10MJ-10MO
MOTOR, HYDRAULIC
CLAMP HOSE HS-16
SIGHT GAUGE AA4724
CAP, FILLER/BREATHER
FITTING, STR 10MJ-10MO
FITTING, 90 12BARB-3/4MP
FITTING
2
1
1
6
1
1
3
2
1
1
1
1
HOSE
FILTER, HYDRAULIC OIL
PLUG 1/2" NPT GALVANIZED
FITTING, 90 4MJ-3/8MP .........................................2................ HYDRAULIC DUMP ONLY
FITTING, 90 DEG
BOLT 3/8" NC X 3" G5
WASHER, LOCK 3/8" MED
SPACER
VALVE, FOUR WAY ASSY. .....................................1................ HYDRAULIC DUMP ONLY
VALVE, TWO WAY ..................................................1................ MANUAL DUMP ONLY
FITTING, STR. ........................................................2................ HYDRAULIC DUMP ONLY
515219
503117
0166 A
515251
34585
3385
511845
3407
13243
TBD
1
3
3
3
KNOB
2
1
HOSE W/ 90 DEG FITTING
HOSE ......................................................................2................ HYDRAULIC DUMP ONLY
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 55
Download from Www.Somanuals.com. All Manuals Search And Download.
FRAME 1 ASSY.
4 LUG HUB AND WHEEL (1-1/16 AXLE SPINDLE)
S/N KA26943T0 HD27963
JANUARY 1996 — APRIL 1999
PAGE 56 —WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
FRAME 1 ASSY.
4 LUG HUB AND WHEEL (1-1/16 AXLE SPINDLE)
S/N KA26943T0 HD27963
JANUARY 1996 — APRIL 1999
NO
1
2
PART NO
13212
29194
PART NAME
QTY.
REMARK
GROMMET ...............................................1 ............ WITH DUMP (HYDRAULIC DUMP CYL.)
LUG NUT...................................................8 ............ REPLACES 8115
3
13120
MAIN FRAME ...........................................1 ............ S/N KA26943 TO II27769
................................................................................. NO LONGER AVAILABLE. USE 13365.
MAIN FRAME ...........................................1 ............ S/N II27770
3
4
5
6
7
8
13365
10133
0447
10176
511493
1023
LOCK NUT 3/8-16
FLAT WASHER 1/2"
LOCK NUT 1/2-13
GRATE LATCH
1
1
12
1
1
HHCS 3/8-16 X 1.1/4"
9
13280
3102
3469
13363KIT
3028
DRUM LOCK LEVER ................................1 ............ W/O DUMP (MANUAL ONLY)
HANDLE GRIP ..........................................1 ............ W/O DUMP (MANUAL ONLY)
DUST CAP ................................................2 ............ REPLACEMENT ONLY
SAFETY CHAIN ASSY .............................1 ............ REPLACES 3148
10
11
12
13
14
15
15
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
U-BOLT
HHCS 1/2-13 X 3.1/2"
2
1
3215
HLC-1
HPC-1
HBC-1
3400
5218
3043
3076
3018
3005
12426
0183
8151
3496
EM903012
3065
3504
516180
TOW BAR (LOOP) ....................................1 ............ CONTACT UNIT SALES
TOW BAR (1 " PIN) ...................................1 ............ CONTACT UNIT SALES
TWO BAR (BALL HITCH 2 -INCH) ............1 ............ CONTACT UNIT SALES
AXLE & HUB ASSY.
HHCS 1/2-13 X 1.1/2"
HHCS 1/2-13 X 6"
AXLE SPRING
LEAF SPRING
2
4
2
2
2
2
WHEEL & TIRE B78-13 (4 HOLE)
CASTLE NUT ............................................2 ............ REPLACES 3068
COTTER PIN
FLAT WASHER 3/4"
BEARING CONE
2
2
4
BEARING CUP .........................................4 ............ REPLACES 3067
SEAL
2
2
1
HUBW/BEARING CUPS (4-LUGS)
SAFETY HOOK
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 57
Download from Www.Somanuals.com. All Manuals Search And Download.
FRAME 2 ASSY.
5 LUG HUB AND WHEEL (1-1/16 AXLE SPINDLE)
S/N HD27964T0 GE210000
APRIL 1999 — MAY 2000
PAGE 58 —WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
FRAME 2 ASSY.
5 LUG HUB AND WHEEL (1-1/16 AXLE SPINDLE)
S/N HD27964T0 GE210000
APRIL 1999 — MAY 2000
NO
1
3
3
4
5
6
7
8
PART NO
13212
13120
13365
10133
0447
10176
511493
1023
PART NAME
QTY.
REMARK
GROMMET ...............................................1 ............ WITH DUMP (HYDRAULIC DUMP CYL.)
MAIN FRAME ...........................................1 ............ S/N KA26943 TO II27769
MAIN FRAME ...........................................1 ............ S/N II27770
LOCK NUT 3/8-16
FLAT WASHER 1/2"
LOCK NUT 1/2-13
GRATE LATCH
1
1
12
1
1
HHCS 3/8-16 X 1.1/4"
9
13280
3102
3148
3028
3215
HLC-1
HPC-1
HBC-1
13382
DRUM LOCK LEVER ................................1 ............ W/O DUMP (MANUAL ONLY)
HANDLE GRIP ..........................................1 ............ W/O DUMP (MANUAL ONLY)
10
12
13
14
15
15
15
16
SAFETY CHAIN ASM
U-BOLT
HHCS 1/2-13 X 3.1/2"
1
2
1
TOW BAR (LOOP) ....................................1 ............ CONTACT UNIT SALES DEPT.
TOW BAR (1 " PIN) ...................................1 ............ CONTACT UNIT SALES DEPT.
TWO BAR (BALL HITCH 2 -INCH) ............1 ............ CONTACT UNIT SALES DEPT.
AXLE & HUB ASM....................................2 ............ NO LONGER AVAILABLE.
................................................................................. SEE FRAME 3 ASSY.
17
18
19
20
21
5218
3043
3076
3018
19045
HHCS 1/2-13 X 1.1/2"
HHCS 1/2-13 X 6"
AXLE SPRING
LEAF SPRING
WHEEL & TIRE
4
2
2
2
2
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 59
Download from Www.Somanuals.com. All Manuals Search And Download.
FRAME 3 ASSY.
5 LUG HUB AND WHEEL (1-1/16 AXLE SPINDLE)
S/N GE21000 AND ABOVE
MAY 2000 AND ABOVE
PAGE 60 —WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
FRAME 3 ASSY.
5 LUG HUB AND WHEEL (1-1/16 AXLE SPINDLE)
S/N GE21000 AND ABOVE
MAY 2000 AND ABOVE
NO
1
2
PART NO
13212
EM941280
PART NAME
GROMMET ............................................. 1 ............. WITH DUMP (HYDRAULIC DUMP CYL.)
LUG NUT
QTY.
REMARK
8
3
13120
MAIN FRAME ......................................... 1 ............. S/N KA26943 TO II27769
................................................................................. NO LONGER AVAILABLE. USE 13365.
MAIN FRAME ......................................... 1 ............. S/N II27770
3
13365
4
5
6
7
10133
0447
10176
511493
1023
LOCK NUT 3/8-16
FLAT WASHER 1/2"
LOCK NUT 1/2-13
GRATE LATCH
1
1
12
1
1
8
HHCS 3/8-16 X 1.1/4"
9
13280
3102
EM941278
13363KIT
3028
3215
HLC-1
HPC-1
HBC-1
511699
5218
3043
3076
3018
19045
EM968302
0183
EM923161
EM903168
EM903169
EM914324
EM941277
EM903113
EM903012
516180
DRUM LOCK LEVER .............................. 1 ............. W/O DUMP (MANUAL ONLY)
HANDLE GRIP ........................................ 1 ............. W/O DUMP (MANUAL ONLY)
DUST CAP .............................................. 2 ............. REPLACEMENT ONLY
SAFETY CHAIN ASM............................. 1 ............. REPLACES 3148
10
11
12
13
14
15
15
15
16
17
18
19
20
21
22
23
24
25
26
27
28
30
31
32
U-BOLT
HHCS 1/2-13 X 3-1/2"
2
1
TOW BAR (LOOP) .................................. 1 ............. CONTACT UNIT SALES
TOW BAR (1 " PIN) ................................. 1 ............. CONTACT UNIT SALES
TWO BAR (BALL HITCH 2 -INCH) .......... 1 ............. CONTACT UNIT SALES
AXLE, NEW STYLE
HHCS 1/2-13 X 1-1/2"
HHCS 1/2-13 X 6"
AXLE SPRING
LEAF SPRING
WHEEL & TIRE
CASTLE NUT, 3/4-16
COTTER PIN, 1/8X1-1/4
FLAT WASHER 3/4"
BEARING CONE INNER
BEARING CUP INNER
SEAL
1
4
2
2
2
2
2
2
2
4
4
2
*
*
*
*
*
HUBW/BEARING CUPS (5-LUG) ........... 2 ............. INCLUDES ITEMS W/
*
BEARING CONE OUTER
BEARING CUPS OUTER
SAFETY HOOK
2
2
1
*
*
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 61
Download from Www.Somanuals.com. All Manuals Search And Download.
PLASTIC ENGINE COVER ASSY.
S/N KA26943TO GE 210000
JANUARY 1996 TO MAY 2000
PAGE 62 —WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
PLASTIC ENGINE COVER ASSY.
S/N KA26943TO GE 210000
JANUARY 1996 TO MAY 2000
NO
1
2
PART NO
13221
3089
PART NAME
QTY.
REMARK
ENGINE COVER ASSY. - PLASTIC ONLY ........1........... S/N KA26943 TO GE210000
HINGE PIN
FLAT WASHER 3/4"
1
2
3
8151
4
5
6
7
8
9
0183
3163
3162
10024
3164
0948
COTTER PIN
2
3
1
11
6
10
SMALL HINGE PLATE
LARGE HINGE PLATE
LOCK NUT 1/4-20
FHSCS 1/4-20 X 1"
LOCK WASHER 1/4"
10
491010
SHROUD FASTENER ASSY. ............................4........... REPLACES 929025
......................................................................................... INCLUDES ITEMS W/
*
11
COTTER PIN
CLEVIS PIN
HHCS 1/4-20 X 3/4"
SHROUD BRACE
LOCK NUT 8-32
RHMS 8-32 X 1/2"
FLAT WASHER #10
4
4
10
1
8
8
*
12
13
14
15
16
17
*
0131A
3401
13287
1307
2203
4
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 63
Download from Www.Somanuals.com. All Manuals Search And Download.
STEEL ENGINE COVER ASSY.
GE 210001 AND ABOVE
MAY 2000 AND ABOVE
PAGE 64 —WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
STEEL ENGINE COVER ASSY.
GE 210001 AND ABOVE
MAY 2000 AND ABOVE
NO.
1
2
3
4
5
6
7
PART NO.
511580
509726
491010
1284
4001
10133
1307
PART NAME
QTY.
REMARKS
ENGINE COVER-STEEL...................................... 1 .......... S/N GE210001 AND ABOVE
HINGE
2
2
4
8
4
6
RUBBER LATCH ASSY.
SCREW, HHCS 3/8-16 X 1-1/2"
FLAT WASHER 3/8"
LOCK NUT 3/8-16
RHMS 8-32 X 1/2"
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 65
Download from Www.Somanuals.com. All Manuals Search And Download.
SINGLE PHASE, 5 HP ELECTRIC MOTOR ASSY.
PAGE 66 —WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
SINGLE PHASE, 5 HP ELECTRIC MOTOR ASSY.
NO.
2
4
PART NO.
0166 A
EM963610
492581
EM963610
13291
PART NAME
QTY.
REMARKS
WASHER, LOCK 3/8 MED. ..................................... 2................ REPLACES 492624
CAPSCREW 3/8" NCX1-1/4" G8 ............................. 6................ REPLACES 492375
NUT 1/4" - 20 NYLON LOCKNUT
CAPSCREW 3/8" NCX1-1/4" G8 ............................. 2................ REPLACES 492376
STARTER MOUNT
6
3
12
14
18
20
22
24
26
28
30
32
34
36
40
42
46
48
50
52
54
56
58
62
1
1
13375
PUMP, EATON 26005-RBBJ
EM963610
EM923057
981635
3416
3418
3420
CAPSCREW 3/8" NCX1-1/4" G8 ............................. 2................ REPLACES 492376
WASHER 1/4" ......................................................... 6................ REPLACES 492596
BOLT, HEX 1/2" - 13 NCX1 ..................................... 4................ REPLACES 492392
ADAPTER, C-FACE PUMP
INSERT, RUBBER
COUPLER, PUMP END
COUPLER, MOTOR END
WASHER, LOCK 1/2" .............................................. 4................ REPLACES 492626
1
1
1
1
3421
6109180
492356
EM98187
13289
511630
508683
505502
EM940162
EM201794
505403
3414
BOLT 1/4" X 3/4"
3
1
2
1
1
3
2
1
1
1
1
SWITCH ASSY, 5HP 1PH
BAR, MOTOR MOUNT
CABLE, .7 M
CABLE, .4 M
WIRE CONNECTOR
CONDUIT CONNECTOR
PIGTAIL ASSY 250 V 30A
TERMINAL
MOTOR, ELECTRIC, 5HP 1PH
CONNECTOR
517031
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 67
Download from Www.Somanuals.com. All Manuals Search And Download.
THREE PHASE, 5 HP ELECTRIC MOTOR ASSY.
PAGE 68 —WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
THREE PHASE, 5 HP ELECTRIC MOTOR ASSY.
NO.
2
4
6
8
PART NO.
0166 A
EM963610
492581
EM963610
13375
PART NAME
QTY.
REMARKS
WASHER, LOCK 3/8 MED. .................................... 10............... REPLACES 492624
CAPSCREW 3/8" NCX1-1/4" G8 ............................. 2................ REPLACES 492375
NUT 1/4" - 20 NYLON LOCKNUT
CAPSCREW 3/8" NCX1-1/4" G8 ............................. 8................ REPLACES 492376
PUMP, EATON 26005-RBBJ
3
10
12
14
16
18
20
22
26
28
30
32
34
36
38
40
42
44
46
48
50
52
1
EM923057
981635
3418
WASHER 1/4" ......................................................... 6................ REPLACES 492596
BOLT, HEX 1/2" - 13 NCX1 ..................................... 4................ REPLACES 492392
INSERT, RUBBER
COUPLER, PUMP END
1
1
3420
6109180
492356
EM98191
13289
13291
3416
WASHER, LOCK 1/2" .............................................. 4................ REPLACES 492626
BOLT 1/4" X 3/4"
3
1
2
1
1
1
1
1
1
1
1
1
4
1
1
SWITCH ASSY, 5HP 3PH
BAR, MOTOR MOUNT
STARTER MOUNT
ADAPTER, C-FACE PUMP
COUPLER, MOTOR END
CONDUIT CONNECTOR
CONNECTOR
CABLE, .7 M
CABLE, .4 M
TERMINAL
3-PRONG PLUG
3421
EM940162
517031
508683
511650
505403
511647
EM940255
512459
3481
WIRE CONNECTOR
CONNECTOR
MOTOR, ELECTRIC, 5HP 3PH
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 69
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA ENGINE ASSY.
PAGE 70 —WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA ENGINE ASSY.
NO.
1
2
3
4
5
6
7
8
PART NO.
3364
203148
203123F
491797
29174-001
29173-001
0310
PART NAME
ENGINE, HONDA 13HP GX390U1QA2
TUBE, EXHAUST
PLATE
RIVET, ID PLATE
KNOB-MUSHROOM
SWITCH, PUSH-PULL W/O KNOB
KEY 1/4 SQUARE 1-1/2
SCREW CAP 3/8"
QTY.
REMARKS
1
1
1
4
1
1
1
4
492379
9
3019092
EM969013
203040
516282
0166 A
EM963610
13374
WASHER 3/8" FLAT ................................................ 6................ REPLACES 492598
NUT NYLOCK ......................................................... 4................ REPLACES 492583
10
11
12
13
14
15
SLEEVE, ENGINE SHAFT, HONDA
COUPLING ASSY
1
1
WASHER LOCK 3/8" ............................................... 6................ REPLACES 492624
CAPSCREW 3/8" NC X 1-1/4" G8........................... 6................ REPLACES 492376
PUMP, EATON 26003-RAG
1
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 71
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX390K1QA2/GX390U1QA2 — AIR CLEANER ASSY.
PAGE 72 —WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX390K1QA2/GX390U1QA2 — AIR CLEANER ASSY.
NO.
1
PART NO.
PART NAME
GASKET, ELBOW
ELEMENT, AIR CLEANER ................ 1 ........ INCLUDES ITEMS W/#
FILTER, OUTER
COVER, AIR CLEANER
GROMMET, AIR CLEANER
NOSE, SILENCER
NOSE, SILENCER............................. 1 ........ S/N 1040439 AND BELOW
NOSE, SILENCER............................. 1 ........ S/N 1040440 AND ABOVE
COLLAR, AIR CLEANER
COLLAR B, AIR CLEANER
ELBOW, AIR CLEANER .................... 1 ........ INCLUDES ITEMS W/
WINGNUT, 6MM
WINGNUT, TOOL BOX SETTING
BOLT- WASHER 6X22
NUT, FLANGE 6MM
QTY.
1
REMARKS
16271ZE2000
17210ZE3010
17218ZE3000
17231ZE3W01
17232891000
17235ZH9N00
17235ZH9N00
17235ZH9N01
17238ZE2310
17239ZE1000
17410ZH9N00
90203ZA0800
90325044000
90009ZE2003
9405006000
2
3
4
5
6
6
6
7
8
9
#
1
1
1
1
#
◊
◊
2
1
*
*
*
11
12
13
14
1
1
1
2
GX390K1QA2: Model WM120 December 2006 And Below
GX340U1QA2: Model WM120 January 2007 And Above
◊
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 73
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX390K1QA2/GX390U1QA2 — CAMSHAFT ASSY.
PAGE 74 —WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX390K1QA2/GX390U1QA2 — CAMSHAFT ASSY.
NO.
PART NO.
14100ZF6W0
PART NAME
QTY.
REMARKS
1
◊
CAMSHAFT ASSEMBLY ............................... 1................ INCLUDES ITEMS W/
.......................................................................................... SN 2391939 AND BELOW
CAMSHAFT ASSEMBLY ............................... 1................ INCLUDES ITEMS W/
.......................................................................................... SN 2391940 AND ABOVE
CAMSHAFT ASSEMBLY
ROD, PUSH
ARM, VALVE ROCKER..................................2................ REPLACES 14431ZE2000
*
1
14100ZF6W01
*
1
2
3
4
5
6
7
8
9
14100ZF6W01
14410ZE3013
14431ZE2010
14441ZE2000
14451ZE1013
14568ZE1000
14711ZE3000
14721ZE3000
14751ZE2003
14771ZE2000
14773ZE2000
14775ZE2010
14781ZE2000
14791ZE2010
90012ZE0010
90206ZE1000
12209ZE8003
12209ZE8003
1
2
LIFTER, VALVE
2
2
1
1
1
2
1
1
1
1
1
2
2
PIVOT, ROCKER ARM
SPRING, WEIGHT RETURN
VALVE, INTAKE
VALVE, EXHAUST
SPRING, VALVE
RETAINER, INTAKE VALVE SPRING
RETAINER, EXHAUST VALVE SPRING
SEAT, VALVE SPRING
ROTATOR, VALVE
PLATE, PUSH ROD GUIDE
BOLT, PIVOT 8MM
*
10
11
12
13
14
15
16
17
17
NUT, PIVOT ADJ.
SEAL, VALVE STEM .....................................1................ USE FROM ENGINE SN 3065844
SEAL, VALVE STEM
◊
1
GX390K1QA2: Model WM120 December 2006 And Below
GX340U1QA2: Model WM120 January 2007 And Above
◊
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 75
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX390K1QA2/GX390U1QA2 — PISTON ASSY.
PAGE 76 —WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX390K1QA2/GX390U1QA2 — PISTON ASSY.
NO. PART NO.
PART NAME
RING SET, PISTON (STD.)
RING SET, PISTON (STD.)
QTY. REMARKS
1
1
1
1
1
1
1
1
1
2
2
2
2
3
4
13010ZF6003
13010ZF6005
13011ZF6003
13011ZF6005
13012ZF6003
13012ZF6005
13012ZF6005
13013ZF6003
13013ZF6005
13101ZF6W00
13102ZF6W00
13103ZF6W00
13104ZF6W00
13111ZF6W00
13200ZE3010
1
1
1
1
1
1
1
1
1
1
1
1
1
1
RING SET, PISTON (OS 0.25), OPT.
RING SET, PISTON (OS 0.25), OPT.
RING SET, PISTON (OS 0.50), OPT.
RING SET, PISTON (OS 0.50), OPT.
RING SET, PISTON (OS 0.50), OPT.
RING SET, PISTON (0.75) NIP.,OPT.
RING SET, PISTON (0.75) NIP.,OPT.
PISTON (STANDARD)
PISTON (OS 0.25), OPTIONAL
PISTON (OS 0.50), OPTIONAL
PISTON (0.75), OPTIONAL
PIN, PISTON
ROD ASSY., CONNECTING (STD.) ......... 1 .......INCLUDES ITEMS W/
............................................................................SN 3177434 AND BELOW
ROD ASSY., CONNECTING (STD.) ......... 1 .......INCLUDES ITEMS W/
............................................................................SN 3177435 AND ABOVE
*
4
13200ZE3020
*
4
4
4
5
6
◊
◊
13200ZE3315
13200ZE3020
13200ZE3315
90001ZE8000
90601ZE3000
ROD ASSY., CONNECTING (US 0.25)..... 1 .......INCLUDES ITEMS W/
ROD ASSY., CONNECTING (STD.) ......... 1 .......INCLUDES ITEMS W/
ROD ASSY., CONNECTING (US 0.25)..... 1 .......INCLUDES ITEMS W/
*
*
*
BOLT, CONNECTING ROD
CLIP, PISTON PIN 20MM
2
2
*
GX390K1QA2: Model WM120 December 2006 And Below
GX340U1QA2: Model WM120 January 2007 And Above
◊
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 77
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX390K1QA2/GX390U1QA2 — CRANKCASE COVER ASSY.
PAGE 78 —WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX390K1QA2/GX390U1QA2 — CRANKCASE COVER ASSY.
NO.
PART NO.
06165ZE3000
11300ZE3602
PART NAME
QTY.
REMARKS
1
2
GOVERNOR KIT (OPIONAL)........................... 1 ......... INCLUDES ITEMS W/
COVER ASSY., CRANKCASE (Q TYPE) ........ 1 ......... INCLUDES ITEMS W/
...................................................................................... S/N 3287256 AND BELOW
COVER ASSY., CRANKCASE (Q TYPE) ........ 1 ......... INCLUDES ITEMS W/
...................................................................................... S/N 3287257 AND ABOVE
#
*
*
2
11300ZE3604
*
2
3
3
3
4
5
◊
◊
11300ZE3604
11381ZE3800
11381ZE3801
11381ZE3801
15600ZG4003
15600735003
COVER ASSY., CRANKCASE (Q TYPE)
GASKET, CASE COVER ................................. 1 ......... S/N 2949254 AND BELOW
GASKET, CASE COVER ................................. 1 ......... S/N 2949255 AND ABOVE
GASKET, CASE COVER
CAP ASSEMBLY, OIL FILLER ......................... 1 ......... INCLUDES ITEMS W/
CAP ASSEMBLY, OIL FILLER ......................... 1 ......... INCLUDES ITEMS W/
GASKET, OIL FILLER CAP
GOVERNOR ASSEMBLY ................................ 1 ......... INCLUDES ITEMS W/+
WEIGHT, GOVERNOR
HOLDER, GOVERNOR WEIGHT
PIN, GOVERNOR WEIGHT
SLIDER, GOVERNOR...................................... 1 ......... S/N 3287256 AND BELOW
SLIDER, GOVERNOR...................................... 1 ......... S/N 3287257 AND ABOVE
SLIDER, GOVERNOR
CLIP, GOVERNOR HOLDER
PIN, DOWEL 8X12
OIL SEAL 36X52X8
WASHER, PLAIN 6MM
BOLT, FLANGE 8X40
1
1
%
%
8
%
15625ZE1003
16510ZE3000
+ 16511ZE8000
+ 16512ZE3000
+ 16513ZE2000
2
9
#
*
10
11
12
13
13
#
#
#
3
1
3
*
*
*
#
#
#
16531ZE2000
16531Z0A000
16531Z0A000
90602ZE1000
90701HC4000
91201ZE3004
9410106800
957010804000
961006202000
961006207000
*
*
13
15
◊
1
1
2
1
1
7
1
1
*
#
*
16
17
18
19
20
21
*
*
#
BEARING, RADIAL BALL 6202
BEARING, RADIAL BALL 6207
*
*
GX390K1QA2: Model WM120 December 2006 And Below
GX340U1QA2: Model WM120 January 2007 And Above
◊
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 79
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX390K1QA2/GX390U1QA2 — CRANKSHAFT ASSY.
PAGE 80 —WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX390K1QA2/GX390U1QA2 — CRANKSHAFT ASSY.
NO.
PART NO.
PART NAME
QTY.
REMARKS
2
2
2
6
9
◊
◊
13310ZF6W10
13310ZF6W11
13310ZF6W12
13351ZE3010
90745ZE2600
91001ZF6003
91001ZF6003
91001ZF6013
CRANKSHAFT, Q-TYPE .................................. 1 ......... INCLUDES ITEMS W/
CRANKSHAFT COMP. .................................... 1 ......... S/N 1113739 AND BELOW
CRANKSHAFT COMP. .................................... 1 ......... S/N 1113740 AND ABOVE
WEIGHT, BALANCER
KEY 6.3X6.3X43
BEARING, RADIAL BALL 6207S
BEARING, RADIAL BALL 6207S..................... 1 ......... S/N 1113739 AND BELOW
BEARING, RADIAL BALL 6207SH .................. 1 ......... S/N 1113740 AND ABOVE
*
1
1
1
10
10
10
◊
◊
*
*
*
GX390K1QA2: Model WM120 December 2006 And Below
GX340U1QA2: Model WM120 January 2007 And Above
◊
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 81
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX390K1QA2/GX390U1QA2 — CYLINDER BARREL ASSY.
PAGE 82 —WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX390K1QA2/GX390U1QA2 — CYLINDER BARREL ASSY.
NO.
PART NO.
12000ZF6W12
PART NAME
QTY. REMARKS
1
BARREL ASSY., CYL. ALERT OIL .......... 1.......INCLUDES ITEMS W/
*
...........................................................................SN 3020570 AND BELOW
BARREL ASSY., CYL. ALERT OIL .......... 1.......INCLUDES ITEMS W/
1
12000ZF6W13
*
...........................................................................SN 3020571 AND ABOVE
1
2
2
2
◊
12000ZF6417
15510ZE2023
15510ZE2033
15510ZE2043
BARREL ASSY., CYL. ALERT OIL .......... 1.......INCLUDES ITEMS W/
SWITCH ASSY., OIL LEVEL ................... 1.......S/N 2334667 AND BELOW
*
SWITCH ASSY., OIL LEVEL ................... 1.......2334668 ~ 2456575
SWITCH ASSY., OIL LEVEL ................... 1.......REPLACES 15510ZE2033
...........................................................................S/N 2456576 AND ABOVE
SWITCH ASSY., OIL LEVEL ................... 1.......REPLACES 15510ZE2033
...........................................................................S/N 1412956 AND BELOW
SWITCH ASSY., OIL LEVEL ................... 1.......S/N 1412957 AND ABOVE
2
◊
◊
15510ZE2043
2
3
4
15510ZE2053
16541ZE3010
32197ZE2003
SHAFT, GOVERNOR ARM
1
SUB-HARNESS ....................................... 1.......USE UP TO ENGINE SN 2334667
5
6
7
9
10
11
12
13
14
15
16
90013883000
90131883000
90446KE1000
91201ZE3004
91203952771
91353671004
9405010000
BOLT, FLANGE 6X12 (CT200) ................. 1.......USE UP TO ENGINE SN 2334667
BOLT, DRAIN PLUG 12 X 15
WASHER 8.2X17X0.8
OIL SEAL 35X52X8
2
1
1
1
1
1
2
1
2
1
*
OIL SEAL 8X14X5
*
O- RING 13.5X1.5 (ARAI)
NUT, FLANGE 10mm.
WASHER, DRAIN PLUG 12mm.
PIN,LOCK 10mm.
BOLT, FLANGE 6X12
BEARING, RADIAL BALL 6202
9410912000
9425110000
957010601200
961006202000
90013883000
90013883000
34150ZH7003
34150ZH7003
34150ZH7013
*
17
17
18
18
18
◊
◊
◊
BOLT, FLANGE 6X12 (CT200) ................. 1.......USE FROM ENGINE SN 2468555
BOLT, FLANGE 6X12 (CT200)
1
ALERT UNIT, OIL..................................... 1.......USE FROM ENGINE SN 2468555
ALERT UNIT, OIL..................................... 1.......S/N 1419413 AND BELOW
ALERT UNIT, OIL..................................... 1.......S/N 1419414 AND ABOVE
GX390K1QA2: Model WM120 December 2006 And Below
GX340U1QA2: Model WM120 January 2007 And Above
◊
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 83
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX390K1QA2/GX390U1QA2 — CYLINDER HEAD ASSY.
PAGE 84 —WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX390K1QA2/GX390U1QA2 — CYLINDER HEAD ASSY.
NO.
PART NO.
PART NAME
QTY.
REMARKS
1
1
2
3
4
5
6
6
6
7
7
12200ZF6W01
12200ZF6406
12204ZE2306
12205ZE2305
12216ZE2300
12251ZF6W00
12310ZE3791
12310ZE2020
12310ZE2020
950051110530
950051110530
CYLINDER HEAD ............................................ 1 ......... INCLUDES ITEMS W/
CYLINDER HEAD ............................................ 1 ......... INCLUDES ITEMS W/
GUIDE, VALVE OS (OPTIONAL)
GUIDE, EX. VALVE OS (OPTIONAL)
CLIP, VALVE GUIDE
*
*
◊
1
1
1
1
*
*
*
◊
◊
GASKET, CYLINDER HEAD
COVER, HEAD ................................................ 1 ......... SN 2378736 AND BELOW
COVER, HEAD ................................................ 1 ......... SN 2378737 AND ABOVE
COVER, HEAD ................................................ 1
TUBE, 11X105 ................................................. 1 ......... REPL. 950051100130M
TUBE, 11X105 ................................................. 1 ......... SN 2368041 AND BELOW
...................................................................................... REPL. 950051100130M
TUBE, BREATHER .......................................... 1 ......... SN 2368042 AND ABOVE
GASKET, CYLINDER HEAD COVER
BOLT, HEAD COVER
BOLT, STUD 8X131.5
BOLT 2, STUD 8X47
7
8
12315ZE3840
12391ZE2020
90014ZE2000
90042ZE8000
90047ZE2000
92900080320E
1
1
2
2
11
12
13
13
S/N 2638033 AND BELOW
BOLT 2, STUD 8X32 ........................................ 2 ......... REPLACES 90047ZE2000
...................................................................................... S/N 2638034 AND ABOVE
13
14
15
16
16
16
17
17
17
17
◊
92900080320E
90441ZE2010
9430112200
957251008000
957251008000
957011008000
9807955846
9807955855
9807956846
9807956855
BOLT 2, STUD 8X32
2
1
2
4
WASHER, HEAD COVER
PIN A, DOWEL 12X20
BOLT, FLANGE 10X80
BOLT, FLANGE 10X80 ..................................... 4 ......... S/N 1411816 AND BELOW
BOLT, FLANGE 10X80 ..................................... 4 ......... S/N 1411817 AND ABOVE
SPARK PLUG BPR5ES (NGK), OPT.
SPARK PLUG W16EPR-U (DENSO), OPT.
SPARK PLUG BPR6ES (NGK)
◊
◊
1
1
1
1
SPARK PLUGW20EPR-U (DENSO)
GX390K1QA2: Model WM120 December 2006 And Below
GX340U1QA2: Model WM120 January 2007 And Above
◊
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 85
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX390K1QA2/GX390U1QA2 — FAN COVER ASSY.
PAGE 86 —WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX390K1QA2/GX390U1QA2 — FAN COVER ASSY.
NO.
1
2
PART NO.
PART NAME
CLIP, TUBE
COVER, FAN *R280*, RED
SHROUD
SUB-HARNESS ........................................... 1 ......... SN 2334667 AND BELOW
SWITCH ASSY., ENGINE STOP ................. 1 ......... SN 2334667 AND BELOW
SWITCH ASSY., ENGINE STOP ................. 1 ......... SN 2334668 AND ABOVE
SWITCH ASSY., ENGINE STOP ................. 1 ......... SN 1412956 AND BELOW
SWITCH ASSY., ENGINE STOP ................. 1 ......... SN 1412957 AND ABOVE
QTY.
REMARKS
16731ZE2003
19610ZE3010ZA
19631ZE3W00
32197ZH8003
36100ZE1015
36100ZH7003
36100ZF6P81
36100ZF6P82
90013883000
90684ZA0601
1
1
1
3
4
5
5
5
5
7
9
◊
◊
BOLT, FLANGE 6X12 (CT200)
CLIP, WIRE HARNESS
6
1
GX390K1QA2: Model WM120 December 2006 And Below
GX340U1QA2: Model WM120 January 2007 And Above
◊
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 87
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX390K1QA2/GX390U1QA2 — FLYWHEEL ASSY.
PAGE 88 —WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX390K1QA2/GX390U1QA2 — FLYWHEEL ASSY.
NO.
1
2
PART NO.
PART NAME
FAN, COOLING
QTY.
REMARKS
19511ZE3000
28450ZE3W11
31100ZE3701
90201ZE3790
90201ZE3V00
90201ZE3V00
90201ZE3790
90741ZE2000
1
1
1
PULLEY, STARTER (SCREEN GRID)
FLYWHEEL
NUT, SPECIAL 16MM .................................. 1 ......... S/N 2263434 AND BELOW
NUT, SPECIAL 16MM (1)............................. 1 ......... S/N 2263435 AND ABOVE
NUT, SPECIAL 16MM (1)............................. 1 ......... S/N 1317976 AND BELOW
NUT, SPECIAL 16MM .................................. 1 ......... S/N 1317977 AND ABOVE
4
6
6
6
6
7
◊
◊
KEY, SPECIAL WOODRUFF 25X18
1
GX390K1QA2: Model WM120 December 2006 And Below
GX340U1QA2: Model WM120 January 2007 And Above
◊
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 89
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX390K1QA2/GX390U1QA2 — IGNITION COIL ASSY.
PAGE 90 —WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX390K1QA2/GX390U1QA2 — IGNITION COIL ASSY.
NO.
PART NO.
PART NAME
QTY.
REMARKS
1
1
1
2
5
8
◊
◊
30500ZF6W02
30500ZF6W02
30500ZF6W03
30700ZE1013
31512ZE2000
36101ZE2701
90015883000
90684ZA0601
COIL ASSEMBLY, IGNITION ....................... 1 ......... REPLACES 305007E2023
COIL ASSEMBLY, IGNITION ....................... 1 ......... S/N 1411816 AND BELOW
COIL ASSEMBLY, IGNITION ....................... 1 ......... S/N 1411817 AND ABOVE
CAP ASSEMBLY, NOISE SUPPRESSOR
GROMMET, WIRE
WIRE, STOP SWITCH 430MM
BOLT, FLANGE 6X28
CLIP, HARNESS
1
1
1
2
1
12
13
◊
GX390K1QA2: Model WM120 December 2006 And Below
GX340U1QA2: Model WM120 January 2007 And Above
◊
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 91
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX390K1QA2/GX390U1QA2 — CARBURETOR ASSY.
PAGE 92 —WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX390K1QA2/GX390U1QA2 — CARBURETOR ASSY.
CARBURETOR ASSY.
NO.
PART NO.
PART NAME
QTY.
REMARKS
1
2
3
4
#%
16010ZE2812
16011ZA0931
16013ZA0931
16015ZE2005
GASKET SET .............................................. 1 ......... INCLUDES ITEM W/&
VALVE SET, FLOAT
FLOAT SET
1
1
*
*
*
CHAMBER SET, FLOAT .............................. 1 ......... INCLUDES ITEMS W/
.................................................................................. S/N BE85B A AND BELOW
CHAMBER SET, FLOAT .............................. 1 ......... INCLUDES ITEMS W/
.................................................................................. S/N BE85B B AND ABOVE
%
4
4
16015ZE8005
16015ZE8005
%
*
◊
CHAMBER SET, FLOAT
1
*
5
6
7
8
9
16016ZH7W01
16024ZE1811
16028ZE0005
16044ZE3W20
16100ZF6V00
SCREW SET
1
*
%
*
SCREW SET, DRAIN ................................... 1 ......... INCLUDES ITEMS W/
SCREW SET B ............................................ 1 ......... INCLUDES ITEMS W/
CHOKE SET
CARBURETOR ASSY., BE85BA ................. 1 ......... INCLUDES ITEMS W/
.................................................................................. S/N 2255423 AND BELOW
CARBURETOR ASSY., BE85B B ................ 1 ......... INCLUDES ITEMS W/
.................................................................................. S/N 2255424 AND ABOVE
#
#
*
1
*
*
9
16100ZF6V01
*
9
◊
16100ZF6V01
16124ZE0005
16166ZF6V00
16172ZE3W10
CARBURETOR ASSY., BE85B B ................ 1 ......... INCLUDES ITEMS W/
*
10
11
12
SCREW, THROTTLE STOP
NOZZLE, MAIN
COLLAR, SET
GASKET, FUEL STRAINER CUP
INSULATOR, CARBURETOR
SPACER, CARBURETOR
GASKET, CARBURETOR
GASKET, INSULATOR
1
1
1
1
1
1
1
1
*
*
*
13 & 16173001004
*
14
15
16
17
18
16211ZF6000
16220ZA0702
16221ZF6800
16223ZE3W00
16610ZE1000
LEVER, CHOKE (STANDARD) ....................1 .......... INCLUDES ITEMS W/+
GX390K1QA2: Model WM120 December 2006 And Below
GX340U1QA2: Model WM120 January 2007 And Above
◊
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 93
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX390K1QA2/GX390U1QA2 — MUFFLER ASSY.
PAGE 94 —WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX390K1QA2/GX390U1QA2 — MUFFLER ASSY.
NO.
1
2
3
4
PART NO.
PART NAME
MUFFLER 100DB
PROTECTOR, MUFFLER
PROTECTOR, EXHAUST PIPE
PIPE, EXHAUST
QTY.
REMARKS
18310ZE2W61
18320ZE2W61
18323ZE3W40
18330ZE2W00
18331ZE3810
18331ZE3810
18331ZE3811
18333ZE3800
18333ZK6Y00
18333ZF6W01
18333ZE6W01
18355ZE2W00
18381ZE2W10
90013883000
90050ZE1000
90055ZE1000
90055ZE1000
90006ZE2000
9405008000
1
1
1
1
1
5
5
5
6
6
6
6
7
8
◊
◊
◊
CAP, MUFFLER
CAP, MUFFLER ........................................... 1 ......... S/N 1166160 AND BELOW
CAP, MUFFLER ........................................... 1 ......... S/N 1166161 AND ABOVE
GASKET, EXHAUST PIPE .......................... 1 ......... S/N 2275744 AND BELOW
GASKET, EXHAUST PIPE .......................... 1 ......... 2275745 ~ 2638033
GASKET, EXHAUST PIPE .......................... 1 ......... S/N 2638034 AND ABOVE
GASKET, EXHAUST PIPE
ARRESTER, SPARK
1
1
1
1
4
3
1
1
5
GASKET, MUFFLER (ARRESTER)
BOLT, FLANGE 6X12 (CT200)
SCREW, TAPPING 5X8
SCREW, TAPPING 4X6
SCREW, TAPPING 4X6
SCREW, TAPPING 6X10
NUT, FLANGE 8MM
10
11
12
13
14
15
GX390K1QA2: Model WM120 December 2006 And Below
GX340U1QA2: Model WM120 January 2007 And Above
◊
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 95
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX390K1QA2/GX390U1QA2 — RECOIL STARTER ASSY.
PAGE 96 —WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX390K1QA2/GX390U1QA2 — RECOIL STARTER ASSY.
NO.
PART NO.
PART NAME
QTY. REMARKS
1
1
2
2
3
4
5
6
7
8
9
◊
◊
28400ZE3W01ZA
28400ZE3W01ZP
28410ZE3W01ZA
28410ZE3W01ZP
28421ZE3W01
28422ZE2W01
28441ZE2W01
28442ZE2W01
28443ZE2W01
28444ZE2W01
28445ZE2W01
28461ZE2W02
28462ZE3W01
28469ZE2W01
90004ZE2W01
90008ZE2003
STARTER ASSY., RECOIL *R8*, RED..............1 ....... INCLUDES ITEMS W/
STARTER ASSY., RECOIL *R280*, RED. .........1 ....... INCLUDES ITEMS W/
CASE, RECOIL STARTER *R8*, RED
CASE, RECOIL STARTER *R280*, RED
PULLEY, RECOIL STARTER
RATCHET, STARTER
SPRING, FRICTION
SPRING, STARTER RETURN
SPRING, RATCHET
RETAINER, SPRING
HOLDER, SPRING
*
*
1
1
1
2
1
1
2
1
1
1
1
*
*
*
*
*
*
*
*
*
10
11
12
13
GRIP, STARTER
ROPE, RECOIL STARTER
GRIP, REINFORCEMENT .................................1 ....... UP TO ENG. S/N 584635
SCREW, CENTER
*
*
◊
*
1
3
*
14
BOLT, FLANGE 6X10
GX390K1QA2: Model WM120 December 2006 And Below
GX340U1QA2: Model WM120 January 2007 And Above
◊
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 97
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX390K1QA2/GX390U1QA2— CONTROL ASSY.
PAGE 98 —WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX390K1QA2/GX390U1QA2— CONTROL ASSY.
NO.
2
3
4
5
PART NO.
PART NAME
ARM, GOVERNOR
ROD, GOVERNOR
SPRING, GOVERNOR
SPRING, THROTTLE RETURN
CONTROL ASSEMBLY, REMOTE ............... 1 ......... INCLUDES ITEMS W/
LEVER, CONTROL
SPRING, LEVER
WASHER, CONTROL LEVER
HOLDER, CABLE
SPACER, CONTROL LEVER
BASE, CONTROL (###)
SPRING, CONTROL ADJUSTING
SPRING, CABLE RETURN
BOLT, FLANGE (6X12) (CT200)
BOLT, GOVERNOR ARM
NUT, SELF-LOCK (6MM)
SCREW, PAN (5X32)
QTY.
REMARKS
16551ZE3000
16555ZE3000
16561ZE3000
16562ZE3000
16570ZE3W20
16571ZE3W00
16574ZE1000
1675ZE2W00
16576891000
16578ZE1000
16581ZE3W00
16584883300
16592883310
90013883000
90015ZE5010
90114SA0000
93500050320A
93500050160A
9405006000
1
1
1
1
6
*
10
1
1
1
1
1
1
1
1
2
1
1
1
1
1
*
11
*
12
*
13
*
14
*
15
*
17
*
18
21
*
22
24
*
27
*
28
*
SCREW, PAN (5X16)
NUT, FLANGE (6MM)
29
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 99
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX390K1QA2/GX390U1QA2 — FUEL TANK ASSY.
PAGE 100 —WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX390K1QA2/GX390U1QA2 — FUEL TANK ASSY.
NO.
1
3
PART NO.
16854ZH8000
16955ZE1000
PART NAME
QTY.
REMARKS
RUBBER, SUPPORTER (107MM)
JOINT, FUEL TANK
TANK, FUEL *NH31*
TANK, FUEL *NH1*
TANK, FUEL *T34*
1
1
1
1
1
6
6
6
6
6
6
6
6
6
6
6
6
7
7
7
◊
◊
◊
◊
◊
◊
◊
◊
◊
◊
17510ZE3010ZA
17510ZE3010ZB
17510ZE3010ZA
17510ZE3020ZA
17510ZE3020ZB
17510ZE3020ZD
17510ZE3800ZA
17510ZE3800ZC
17510ZE3800ZE
17510ZE3801ZA
17510ZE3801ZC
17510ZE3801ZE
17620ZH013
TANK, FUEL *NH31* .................................... 1 ......... S/N 1213085 AND BELOW
TANK, FUEL *NH1* ...................................... 1 ......... S/N 1213085 AND BELOW
TANK, FUEL *T34*....................................... 1 ......... S/N 1213085 AND BELOW
TANK, FUEL *NH1* ...................................... 1 ......... 1213086 ~ 1383799
TANK, FUEL *NH31* .................................... 1 ......... 1213086 ~ 1383799
TANK, FUEL *T34*....................................... 1 ......... 1213086 ~ 1383799
TANK, FUEL *NH1* ...................................... 1 ......... S/N 1383800 AND ABOVE
TANK, FUEL *NH31* .................................... 1 ......... S/N 1383800 AND ABOVE
TANK, FUEL *T34*....................................... 1 ......... S/N 1383800 AND ABOVE
CAP COMP., FUEL FILLER ......................... 1 ......... S/N 1383800 AND ABOVE
CAP COMP., FUEL FILLER (BLACK) .......... 1 ......... S/N 1383800 AND ABOVE
CAP COMP., FUEL FILLER ......................... 1 ......... S/N 1530148 AND BELOW
.................................................................................. ( CHROME PLATED)
17620ZH023
17620Z0T305
8
8
8
8
9
9
14
16
18
18
◊
◊
◊
◊
17631ZH7003
17631Z0T812
17631Z4H800
17631Z0T801
17672ZE2W01
17672ZE2W01
91353671004
9405008000
FUEL, FILLER CAP (39X58X3)
1
FUEL, FILLER CAP (39X62X3) ................... 1 ......... S/N 1530148 AND BELOW
FUEL, FILLER CAP (39X62X3) ................... 1 ......... S/N 1530149 ~ 1552033
FUEL, FILLER CAP (39X62X3) ................... 1 ......... S/N 1552034 AND ABOVE
FILTER, FUEL
1
FILTER, FUEL ............................................. 1 ......... S/N 1530148 AND BELOW
O-RING 14MM (NOK)
NUT, FLANGE 8MM
TUBE, FUEL 4.5 X 235................................ 1 ......... REPL. 950014500160M
TUBE, FUEL 4.5 X 235................................ 1 ......... S/N 1105013 AND BELOW
.................................................................................. REPL. 950014500160M
TUBE, FUEL 4.5 X 235 (FKM)..................... 1 ......... S/N 1105014 AND ABOVE
1
2
950014523540
950014523540
◊
18
19
19
19
21
28
28
29
◊
◊
◊
91424Z5L801
9500202080
9500202080
950024080008
957010802500
17620Z4H010
17620Z4H020
17672Z4H000
CLIP, TUBE (B8)
2
CLIP, TUBE (B8) .......................................... 2 ......... S/N 1105013 AND BELOW
CLAMP, TUBE (D8) ...................................... 2 ......... S/N 1105014 AND ABOVE
BOLT, FLANGE 8 X 25
CAP COMP., FUEL FILLER ......................... 1 ......... 1530149 ~ 1552033
CAP COMP., FUEL FILLER ......................... 1 ......... 1552034 AND ABOVE
FILTER, FUEL ........................................... 1 ......... 1530149 AND ABOVE
2
◊
◊
◊
GX390K1QA2: Model WM120 December 2006 And Below
GX340U1QA2: Model WM120 January 2007 And Above
◊
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 101
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX390K1QA2 — GASKET KIT ASSY.
PAGE 102 —WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX390K1QA2 — GASKET KIT ASSY.
NO.
PART NO.
PART NAME
QTY.
REMARKS
1
*
3
*
4
*
5
*
6
*
7
*
8
*
9
11381ZE3800
12251ZF6W00
12391ZE2020
16221ZF6800
16223ZE3W00
18333ZF6W01
18381ZE2W10
061A1Z6700
GASKET, CASE COVER
GASKET, CYLINDER HEAD
GASKET, CYLINDER HEAD COVER
GASKET, CARBURETOR
GASKET, INSULATOR
GASKET, EXHAUST PIPE
GASKET, MUFFLER (ARRESTER)
GASKET KIT ............................................... 1 ......... INCLUDES ITEMS W/
.................................................................................. REPLACES 06111ZF6407
.................................................................................. S/N 2949254
1
1
1
1
1
1
1
*
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 103
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX390K1QA2/GX390U1QA2 — LABELS ASSY.
GX-390K1QA2
GX-39
PAGE 104 —WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX390K1QA2/GX390U1QA2 — LABELS ASSY.
NO.
PART NO.
PART NAME
MARK, OPERATOR
MARK,, THROTTLE INDICATION
EMBLEM ..................................................1............. S/N 3249629 AND BELOW
EMBLEM ..................................................1............. S/N 3249630 AND ABOVE
EMBLEM ..................................................1............. S/N 1398206 AND BELOW
EMBLEM ..................................................1............. S/N 1398207 AND ABOVE
LABEL, CAUTION
MARK, CHOKE (ORANGE)
QTY.
1
1
REMARKS
1
3
4
4
4
4
6
8
9
◊
◊
◊
◊
87516ZH7000
87532ZH7000
87521ZF6W01
87521ZF6W02
87521ZF6W03
87521ZF6W04
87522ZH9010
87528ZE2810
87530ZF6W10
87532ZH8810
87586ZH7W00
1
1
LABEL, SPECIFICATION .........................1............. TO ENGINE S/N 2172909
MARK, OIL ALERT (E)
LABEL, FUEL CAUTION ...........................1............. TO ENGINE S/N 2166102
10
22
1
GX390K1QA2: Model WM120 December 2006 And Below
GX340U1QA2: Model WM120 January 2007 And Above
◊
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 105
Download from Www.Somanuals.com. All Manuals Search And Download.
TERMS AND CONDITIONS OF SALE — PARTS
5. Parts must be in new and resalable
condition, in the original Multiquip
package (if any), and with Multiquip part
numbers clearly marked.
Multiquip reserves the right to quote and
sell direct to Government agencies, and to
Original Equipment Manufacturer accounts
who use our products as integral parts of their
own products.
PAYMENT TERMS
Terms of payment for parts are net 30 days.
FREIGHT POLICY
6. The following items are not returnable:
All parts orders will be shipped collect or
prepaid with the charges added to the invoice.
All shipments are F.O.B. point of origin.
Multiquip’s responsibility ceases when a
signed manifest has been obtained from the
carrier, and any claim for shortage or damage
must be settled between the consignee and
the carrier.
a. Obsolete parts. (If an item is in the
price book and shows as being
replaced by another item, it is
obsolete.)
SPECIAL EXPEDITING SERVICE
A $35.00 surcharge will be added to the
invoice for special handling including bus
shipments, insured parcel post or in cases
where Multiquip must personally deliver the
parts to the carrier.
b. Any parts with a limited shelf life
(such as gaskets, seals, “O” rings,
and other rubber parts) that were
purchased more than six months
prior to the return date.
LIMITATIONS OF SELLER’S LIABILITY
MINIMUM ORDER
Multiquip shall not be liable hereunder for
damages in excess of the purchase price of
the item with respect to which damages are
claimed, and in no event shall Multiquip be
liable for loss of profit or good will or for any
other special, consequential or incidental
damages.
The minimum charge for orders from Multiquip
is $15.00 net. Customers will be asked for
instructions regarding handling of orders not
meeting this requirement.
c. Any line item with an extended
dealer net price of less than
$5.00.
d. Special order items.
RETURNED GOODS POLICY
e. Electrical components.
f. Paint, chemicals, and lubricants.
g. Decals and paper products.
h. Items purchased in kits.
Return shipments will be accepted and
credit will be allowed, subject to the following
provisions:
LIMITATION OF WARRANTIES
No warranties, express or implied, are
made in connection with the sale of parts or
trade accessories nor as to any engine not
manufactured by Multiquip. Such warranties
made in connection with the sale of new,
complete units are made exclusively by a
statement of warranty packaged with such
units, and Multiquip neither assumes nor
authorizes any person to assume for it
any other obligation or liability whatever in
connection with the sale of its products. Apart
from such written statement of warranty,
there are no warranties, express, implied or
statutory, which extend beyond the description
of the products on the face hereof.
1. A Returned Material Authorization
must be approved by Multiquip prior to
shipment.
7. The sender will be notified of any material
received that is not acceptable.
8. Such material will be held for five
working days from notification, pending
instructions. If a reply is not received
within five days, the material will be
returned to the sender at his expense.
2. To obtain a Return Material Authorization,
a list must be provided to Multiquip
Parts Sales that defines item numbers,
quantities, and descriptions of the items
to be returned.
9. Credit on returned parts will be issued
at dealer net price at time of the original
purchase, less a 15% restocking
charge.
a. The parts numbers and descriptions
must match the current parts price
list.
b. The list must be typed or computer
generated.
10. In cases where an item is accepted, for
which the original purchase document
can not be determined, the price will be
based on the list price that was effective
twelve months prior to the RMA date.
c. The list must state the reason(s)
for the return.
Effective: February 22, 2006
d. The list must reference the sales
order(s) or invoice(s) under
which the items were originally
purchased.
11. Credit issued will be applied to future
purchases only.
PRICING AND REBATES
e. The list must include the name
and phone number of the person
requesting the RMA.
Prices are subject to change without prior
notice. Price changes are effective on a
specific date and all orders received on or
after that date will be billed at the revised price.
Rebates for price declines and added charges
for price increases will not be made for stock
on hand at the time of any price change.
3. AcopyoftheReturnMaterialAuthorization
must accompany the return shipment.
4. Freight is at the sender’s expense. All
parts must be returned freight prepaid to
Multiquip’s designated receiving point.
PAGE 106 —WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
WM120PH/SH HYDRAULIC MIXER • OPERATION AND PARTS MANUAL — REV. #7 (09/15/11) — PAGE 107
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION AND PARTS MANUAL
HERE’S HOW TO GET HELP
PLEASE HAVE THE MODEL AND SERIAL
NUMBER ON-HAND WHEN CALLING
UNITED STATES
Multiquip Corporate Office
MQ Parts Department
18910 Wilmington Ave.
Carson, CA 90746
Contact: [email protected]
Tel. (800) 421-1244
Fax (800) 537-3927
800-427-1244
310-537-3700
Fax: 800-672-7877
Fax: 310-637-3284
Service Department
Warranty Department
800-421-1244
310-537-3700
Fax: 310-537-4259
Fax: 310-943-2238
800-421-1244
310-537-3700
Fax: 310-943-2249
Technical Assistance
800-478-1244
MEXICO
UNITED KINGDOM
MQ Cipsa
Multiquip (UK) Limited Head Office
Carr. Fed. Mexico-Puebla KM 126.5
Momoxpan, Cholula, Puebla 72760 Mexico
Contact: [email protected]
Tel: (52) 222-225-9900
Unit 2, Northpoint Industrial Estate, Tel: 0161 339 2223
Fax: (52) 222-285-0420 Globe Lane,
Dukinfield, Cheshire SK16 4UJ
Contact: [email protected]
Fax: 0161 339 3226
CANADA
Multiquip
4110 Industriel Boul.
Laval, Quebec, Canada H7L 6V3
Contact: [email protected]
Tel: (450) 625-2244
Tel: (877) 963-4411
Fax: (450) 625-8664
© COPYRIGHT 2011, MULTIQUIP INC.
Multiquip Inc, the MQ logo and the Whiteman logo are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without written permission. All other
trademarks are the property of their respective owners and used with permission.
This manual MUST accompany the equipment at all times.This manual is considered a permanent part of the equipment and should remain with the unit if resold.
The information and specifications included in this publication were in effect at the time of approval for printing. Illustrations, descriptions, references and technical data contained in
this manual are for guidance only and may not be considered as binding. Multiquip Inc. reserves the right to discontinue or change specifications, design or the information published
in this publication at any time without notice and without incurring any obligations.
Your Local Dealer is:
Download from Www.Somanuals.com. All Manuals Search And Download.
|