OPERATION AND PARTS MANUAL
MODEL GDP5000H
HIGH CYCLE GENERATOR
Revision #2 (07/23/08)
To find the latest revision of this
publication, visit our website at:
THIS MANUAL MUST ACCOMPANYTHE EQUIPMENT AT ALLTIMES.
Download from Www.Somanuals.com. All Manuals Search And Download.
PROPOSITION 65WARNING
PAGE 2 — GDP-5000H A.C. GENERATOR— OPERATION AND PARTS MANUAL — REV. #2 (07/23/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
GDP-5000H A.C. GENERATOR — OPERATION AND PARTS MANUAL — REV. #2 (07/23/08) — PAGE 3
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
Here's How To Get Help .......................................... 3
Table Of Contents ................................................... 4
Parts Ordering Procedures ..................................... 5
Rules For Safe Operation ....................................... 6
Operation and Safety Decals .................................. 7
Specifications .......................................................... 8
General Information ................................................ 9
Honda GX340K1 Gasoline
Engine
Cylinder Head Assy. .......................................... 38-39
Recoil Starter Assy............................................ 40-41
Fan Cover Assy. ................................................ 42-43
Camshaft /Valves Assy. ..................................... 44-45
Piston/Rings Assy.............................................. 46-47
Air Cleaner Assy................................................ 48-49
Cylinder Barrel Assy. (Recoil Starter) ............... 50-51
Cylinder Barrel Assy. (Electric Start) ................. 52-53
Crankcase Governor Assy. ............................... 54-55
Flywheel/Fan Assy. ........................................... 56-57
Coil Assy............................................................ 58-59
Crankshaft Assy. ............................................... 60-61
Electric Starter Assy. ......................................... 62-63
Governor Control Assy. ..................................... 64-65
Carburetor Assy. ............................................... 66-67
Solenoid Assy. ................................................... 68-69
Fuel Cock Assy. ................................................ 70-71
Multiquip GDP-5000H —
ACGenerator
Controls and Indicators .......................................... 10
Installation .............................................................. 11
Pre-Setup ..........................................................12-13
Instrumentation ...................................................... 14
Load Application ...............................................15-16
Operating Instructions............................................ 17
Maintenance .......................................................... 18
Preparation For Long Term Storage ...................... 19
Wiring Diagram ...................................................... 20
Troubleshooting (Engine)..................................21-22
Troubleshooting (Generator) ............................23-24
Explanation Of Codes In Remarks Column ............ 7
Spare Parts List .................................................... 25
Engine/Generator Assy. ....................................26-27
Generator Assy. ................................................28-29
Control Box Assy. ..............................................30-31
Muffler Assy.......................................................32-33
Pipe Frame Assy. ..............................................34-35
Nameplate Assy. .................................................... 36
Terms and Conditions Of Sale — Parts ..................72
NOTE
Specification and part number
are subject to change without
notice.
PAGE 4 — GDP-5000H A.C. GENERATOR— OPERATION AND PARTS MANUAL — REV. #2 (07/23/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS ORDERING PROCEDURES
Ordering parts has never been easier!
Choose from three easy options:
Effective:
January 1st, 2006
Best Deal!
Order via Internet (Dealers Only)
Orderpartson-lineusingMultiquip’sSmartEquipwebsite!
:
If you have an MQ Account, to obtain a
Username and Password, E-mail us at:
■
■
■
View Parts Diagrams
Order Parts
PrintSpecificationInformation
To obtain an MQ Account, contact your
District Sales Manager for more information.
Use the internet and qualify for a 5% Discount
on Standard orders for all orders which include
complete part numbers.*
Gotowww.multiquip.comandclickon
to log in and save!
Order Parts
Note: Discounts Are Subject To Change
Fax your order in and qualify for a 2% Discount
on Standard orders for all orders which include
complete part numbers.*
Order via Fax (Dealers Only)
:
All customers are welcome to order parts via Fax.
Domestic (US) Customers dial:
1-800-6-PARTS-7 (800-672-7877)
Note: Discounts Are Subject To Change
Domestic (US) Dealers Call:
1-800-427-1244
Order via Phone:
Non-Dealer Customers:
International Customers should contact
their local Multiquip Representatives for
Parts Ordering information.
Contact your local Multiquip Dealer for
parts or call 800-427-1244 for help in
locating a dealer near you.
When ordering parts, please supply:
❒
Specify Preferred Method of Shipment:
❒
❒
❒
❒
❒
❒
Dealer Account Number
✓
UPS/Fed Ex
✓ DHL
Dealer Name and Address
■
■
Priority One
Ground
✓
Truck
Shipping Address (if different than billing address)
Return Fax Number
Applicable Model Number
■ Next Day
■
Second/ThirdDay
Quantity, Part Number and Description of Each Part
All orders are treated asStandard Orders
andwillshipthesamedayifreceivedprior
to 3PM PST.
WE ACCEPT ALL MAJOR CREDIT CARDS!
GDP-5000H A.C. GENERATOR — OPERATION AND PARTS MANUAL — REV. #2 (07/23/08) — PAGE 5
Download from Www.Somanuals.com. All Manuals Search And Download.
RULES FOR SAFE OPERATION
■
Provide adequate ventilation when operating the generator.
DO NOT operate the generator in any enclosed or narrow
space. The generator's gasoline engine gives off DEADLY
carbon monoxide gas.
CAUTION:
Failure to follow instructions in this manual
may lead to serious injury or even death!This
equipment is to be operated by trained and
qualified personnel only! This equipment is
for industrial use only.
■
■
■
■
NEVER operate the generator in an explosive atmosphere or
near combustible materials. An explosion or fire could result
causing severe bodily harm or even death.
The following safety guidelines should always be used when
operating the GDP-5000H Generator:
Always make sure that the generator is secure on level ground
so that it cannot slide or shift around, endangering workers.
Also keep the immediate area free of bystanders.
GENERAL SAFETY
■
■
■
DO NOT operate or service this equipment before reading
this entire manual.
When using a concrete vibrator or a similar device that is
immersed in a water based solution, make sure the device is
equipped with short circuit protection.
This equipment should not be operated by persons under 18
years of age.
Always use rubber boots and gloves when operating a
concrete vibrator or similar device.
NEVER operate this equipment without proper protective
clothing, shatterproof glasses, steel-toed boots and other
protective devices required by the job.
■
■
Use adequate size connecting cable for extension.
HighTemperatures – Allow the machine and engine to cool
before adding fuel or performing service and maintenance
functions. Contact with hot components can cause serious
burns.
■
This generator is a source of potentially LETHAL high voltage.
Never permit unqualified personnel-especially children to
operate the generator.
■
■
Always refuel in a well-ventilated area, away from sparks and
open flames.
Emergencies
■
Always know the location of the nearest fire extinguisher
and first aid kit. Know the location of the nearest telephone.
Also know the phone numbers of the nearest ambulance,
doctor and fire department. This information will be
invaluable in the case of an emergency.
Always use extreme caution when working with flammable
liquids. When refueling, stop the engine and allow it to cool.
DO NOT smoke around or near the machine. Fire or explosion
could result from fuel vapors, or if fuel is spilled on a hot
engine.
Maintenance Safety
■
■
This generator is equipped with a ground terminal for your
protection. Always complete the grounding path from the
generator to an external grounding source.
■
NEVER lubricate components or attempt service on a running
machine.
■
Always allow the machine a proper amount of time to cool
before servicing.
NEVER operate this generator, or handle any electrical
equipment while standing in water, while bare foot, while
hands are wet, or in the rain. Electrical shock could occur
causing severe bodily harm or even death.
■
■
Keep the machinery in proper running condition.
Fix damage to the machine immediately and always replace
broken parts.
■
■
Keep electrical cords in good condition. Worn, bare or frayed
wiring can cause electrical shock, leading to bodily harm or
even death.
■
■
■
Dispose of hazardous waste properly.Examples of potentially
hazardous waste are used motor oil, fuel and fuel filters.
This generator requires an adequate free flow of cooling air.
Never operate the generator in any enclosed or narrow area
where free flow of the air is restricted. If the air flow is restricted
it will cause serious damage to the generator and may cause
injury to people.
DO NOT use food or plastic containers to dispose of
hazardous waste.
DO NOT pour waste, oil or fuel directly onto the ground,
down a drain or into any water source
■
NEVER touch the hot exhaust manifold, muffler or cylinder.
Allow these parts to cool before servicing generator.
PAGE 6 — GDP-5000H A.C. GENERATOR— OPERATION AND PARTS MANUAL — REV. #2 (07/23/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION AND SAFETY DECALS
Machine Safety Decals
The GDP-5000H portable generator is equipped with a number of safety decals.These decals are provided for operator safety and
maintenance information.The illustration below shows these decals as they appear on the machine. Should any of these decals
become unreadable, replacements can be obtained from your dealer.
GDP-5000H A.C. GENERATOR — OPERATION AND PARTS MANUAL — REV. #2 (07/23/08) — PAGE 7
Download from Www.Somanuals.com. All Manuals Search And Download.
GDP5000H — SPECIFICATIONS
Table 1. Specifications
MODEL
GDP-5000H
Type
2-pole, Brushless Type Revolving Field
Max. Output
Rated Output
Rated Voltage
Rated Current
Phase
4.0 kW
3.6 kW
120/ 240 V
30.0/15.0 A
60 Cycle Generator
Single Phase (4 wire)
60 Hz
Frequency
Rated Speed
Power Factor
Max.Output
Rated Output
Rated Voltage
Rated Current
Phase
3600 RPM
100%
5 kVA
5 kVA
230 V
12.5 A
180 Cycle Generator
Three Phase (4 wire)
180 Hz
Frequency
Rated Speed
Power Factor
Model
3600 RPM
80%
Honda GX340
Air-cooled 4 stroke OVH 25 inclined cylinder
82 mm X 64 mm
337 cc
Type
Bore X Stroke
Displacementl
Max Output
Rated Output
Fuel Tank Capacity
Fuel
11.0 H.P./3600 R.P.M.
8.0 H.P./3600 R.P.M.
Approx. 5 U.S. Gallons
Unleaded Automobile Gasoline
1 3/4 pints
Engine
Lube Oil Capacity
Speed Control Method
Starting Method
Centrifugal Fly-weight Type
Recoil Start
Dimension (LXWXH)
Dry Net Weight
700 X 560 X 510 mm
231.5 lbs
Effects of Altitude and Heat
The maximum output of the engine listed above is applicable to supplying electrical power for continuous service at ambient
conditions in accordance with SAE Test cord J607. The above ambient conditions are at standard sea level, with a barometric
reading of 29.92 inches and a temperature of 60 degrees fahrenheit.
Generally, the engine output power will decrease 3 1/2% for each 1000 feet of altitude above sea level, and 1% for each 10° F
Fahrenheit above the standard temperature of 60° F
PAGE 8 — GDP-5000H A.C. GENERATOR— OPERATION AND PARTS MANUAL — REV. #2 (07/23/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
GDP-5000H — GENERAL INFORMATION
Excitation System
WARNING:
The GDP-5000H-series generators use a magnet attached
Before connecting this generator to any
to a flywheel to produce AC voltage from a lamp coil beneath
the flywheel. As the magnetic passes the coil it produces
approximately 19-22 AC volts.
building’s electrical system, a licensed
electrician must install an isolation
(transfer) switch.
This voltage (19-22 VAC) is then sent to the control box that
contains three rectifying diodes:
Serious injury or death may result without
this transfer switch.
z
z
z
Excitation (diode 1)
Battery (diode 2)
Slow Down (diode 3)
GDP-5000H FAMILIARIZATION
Generator
The Multiquip Model GDP-5000H generator has been
designed as a portable dual purpose power source for 60
Hz (single phase) lighting facilities, power tools, submersible
pumps and other industrial and construction machinery. In
addition the Model GDP-5000H has been designed as a
power source for 180 Hz, 3-phase concrete vibrators.
The AC voltage will pass through the excitation diode that
converts the voltage to DC power.
This DC power is then sent to the excitation windings housed
within the main windings commonly called the "stator".
This voltage is then transferred into the rotor through
induction.The rotor contains two diodes within it which rectify
the DC voltage and send it out through the main windings,
as AC voltage.
This generator is powered by a HONDA gasoline engine.
The alternator, a brushless revolving-field type, is
permanently aligned to the engine through rigid coupling.
The generator is mounted on rubber vibration isolators that
have a steel base backplate which is attached to the
protective steel pipe carrying frame.The protective carrying
frame is made of steel tubing and fully wraps around the
generator to protect against damage.
Engine
The four-cycle air-cooled HONDA gasoline engine is designed
to meet every performance requirement of this generator.
Reference Table 1, page 8 for engine specifications
This portable generator is supplied with a electrical control
box. To reduce vibration caused by the engine, the control
box is also placed on rubber isolators.
Figure 1 (page 11) shows the basic controls and indicators
for the GDP-5000H generator.
Control Box
The control box is provided with the following:
NOTE
z
z
z
z
z
z
z
z
z
z
z
T
hree 240V output receptacles (three phase).
One 120V output output receptacle (single phase)
One 120/240V output output receptacle (single phase)
One 120V output receptacle, GFIC (single phase)
One main 60 Hz (single phase) circuit breaker
In keeping with Multiquip's policy of
constantly improving its products, the
specifications quoted herein are subject
to change without prior notice.
.
.
.
.
One main 180 Hz (three phase) circuit breaker
.
AC Voltmeter
GroundTerminal
Full Power Switch
Idle Control Switch
Operation Switch
GDP-5000H A.C. GENERATOR — OPERATION AND PARTS MANUAL — REV. #2 (07/23/08) — PAGE 9
Download from Www.Somanuals.com. All Manuals Search And Download.
GDP-5000H — CONTROLS AND INDICATORS
Figure 1. Controls and Indicators
PAGE 10 — GDP-5000H A.C. GENERATOR— OPERATION AND PARTS MANUAL — REV. #2 (07/23/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
GDP-5000H — INSTALLATION
Outdoor Installation
Indoor Installation
Exhaust gases from gasoline engines are extremely
poisonous. Whenever an engine is installed indoors the
exhaust fumes must be vented to the outside. The engine
should be installed at least two feet from any outside wall.
Using an exhaust pipe which is too long or too small can
cause excessive back pressure which will cause the engine
to heat excessively and possibly burn the valves.
Install the generator in a location where it will not be exposed to
rain or sunshine. Make sure that the generator is on secure level
ground so that it cannot slide or shift around. Also install the
generator in a manner so that the exhaust will not be discharged
in the direction of nearby homes.
The installation site must be relatively free from moisture and
dust. All electrical equipment should be protected from excessive
moisture.Failure to do will result in deterioration of the insulation
and will result in short circuits and grounding.
Eliminate the danger of deadly carbon monoxide gas.
Remember that exhaust fumes from any gasoline engine
are very poisonous if discharged in a closed room, but
harmless if allowed to mix with the outside air.If the generator
is installed indoors, you must make provisions for venting
the engine exhaust to the outside of the building.
Foreign materials such as dust, sand, lint and abrasive materials
have a tendency to cause excessive wear, not only to the engine
parts, but also to the alternator parts.
CAUTION :
CAUTION :
Preventing electrical shock. Pay close
attention to handling when operating
concrete vibrators. Always use rubber
boots and gloves to insulate the body from
a short circuit.
Pay close attention to ventilation when
operating the generator inside confined
areas. The engine exhaust contains
noxious elements.
GDP-5000H A.C. GENERATOR — OPERATION AND PARTS MANUAL — REV. #2 (07/23/08) — PAGE 11
Download from Www.Somanuals.com. All Manuals Search And Download.
GDP-5000H — PRE-SETUP
General Inspection Prior to Operation
Ground the Tool
This generator has been thoroughly inspected prior to
shipment from the factory. However, be sure to check for
damaged parts or components, or loose nuts and bolts, which
could have occurred in transit.
Ground the tool (load) in the same manner as the generator.
Circuit Breaker
To protect the generator from an overload, circuit breakers are
provided for both 60 and 180 phases on the control box.
Make sure to switch the circuit breakers to the "OFF" position
prior to starting the engine.
Ground
The nut and ground terminal on the generator should always
be used to connect the generator to a suitable ground. The
ground path should be of #8 size wire.
Extension Cable
When electric power is to be provided to various tools or loads at
some distance from the generator, extension cords are normally
used. Cables should be sized to allow for distance in length and
amperage so that the voltage drop between the generator and
point of use (load) is held to a minimum. Use the cable selection
chart (Tables 2 and 3) as a guide for selecting proper cable size.
Connect the terminal of the ground wire between the lock
washer and the nut and tighten the nut fully. Connect their
end of the wire to a suitable ground.
Ground the Generator
Ground the generator from its ground connector so that the
resistance to ground is 500 ohms or less.
Table 2. Cable Selection (60 Hz, single phase operation)
Load In Watts
At 120 At 240
Maximum Allowable Cable Length
Current
in
Amperes
#10 Wire
#12 Wire
#14 Wire
#16 Wire
Volts
Volts
2.5
5
300
600
1000 ft.
500 ft.
350 ft.
250 ft.
150 ft.
125 ft.
600 ft.
300 ft.
200 ft.
150 ft.
100 ft.
75 ft.
375 ft.
200 ft.
125 ft.
100 ft.
65 ft.
250 ft.
125 ft.
100 ft.
600
1200
1800
2400
3600
4800
7.5
10
15
20
900
1200
1800
2400
50 ft.
CAUTION: Equipment damage can result from low voltage.
Table 3. Cable Selection (180 Hz, 3-phase operation)
Length (ft.)
Load
50
100
150
200
250
300
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3 kVA
2 kVA
1 kVA
0.0031 in
0.0031 in
0.0031 in
0.0031 in
0.0031 in
0.0031 in
0.0031 in
0.0031 in
0.0031 in
0.0054 in
0.0031 in
0.0031 in
0.0054 in
0.0031 in
0.0031 in
0.0085in
2
0.0054 in
0.0031 in
2
PAGE 12 — GDP-5000H A.C. GENERATOR— OPERATION AND PARTS MANUAL — REV. #2 (07/23/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
GDP-5000H — PRE-SETUP
Fuel
Lubrication Oil
Close the fuel cock before filling the tank. Fill the fuel tank
with clean and fresh unleaded gasoline. Do not fill the tank
beyond capacity.
Fill the engine crankcase with lubricating oil through the filler
hole, but do not overfill. Make sure the generator is level.
With the dipstick inserted all the way, but without being
screwed into the filler hole, verify that the oil level is
maintained between the two notches on the dipstick.
Pay attention to the fuel tank capacity when replenishing
fuel. Refer to the fuel tank capacity listed on page 8
Specification Table 1.
The oil listed in Table 4 is recommended to ensure better
engine performance. Use class SC or higher grade motor
oil.
The fuel tank cap must be closed tightly after filling.
Table 4. Recommended Motor Oil
Handle fuel in a safety container. If the container does not have
a spout, use a funnel.
Temperature
Type Oil
Range
CAUTION :
104° F ~ 23° F
SAE 30
(40° C ~ -5°C)
Never fill the fuel tank while the engine is
running or in the dark. Gasoline spillage
on a hot engine can cause a fire or
explosion. If gasoline spillage occurs, wipe
up the spilled gasoline completely to
prevent fire hazards.
23° F ~ 5° F
SAE 20 or sae 10W-30
(-5° C ~ -15°C)
Below 5° C (-15°) SAE 10W or SAE 10W-30
GDP-5000H A.C. GENERATOR — OPERATION AND PARTS MANUAL — REV. #2 (07/23/08) — PAGE 13
Download from Www.Somanuals.com. All Manuals Search And Download.
GDP-5000H — INSTRUMENTATION
CAUTION :
Power Outlets
The generator has the following single and 3-phase
receptacles.
When using a combination of dual
receptacles, total load should not exceed
the rated capacity of the generator.
z
Single Phase
One Duplex NEMA (GFCI) 5-20R (120V, 30 Amp)
One Twist Lock NEMA L5-30R (120V, 30 Amp)
One Twist Lock NEMA L6-20R (240V, 20 Amp)
3- Phase
60 Hz Circuit Breaker
This breaker protects the generator from short circuiting or
overloading from the 60 Hz single phase load.
z
The 180 Hz Leakage Breaker
ThreeTwist Lock NEMA 7410 (240V, 30 Amp)
The 180 Hz leakage breaker (Figure 4) is a earth leakage
breaker with the following conditions:
Full Power Switch
The unit is provided with a full power switch. Figures 2 and 3
show simplified wiring diagrams of the dual voltage system.
z
The circuit is broken when the load side shorts or there
is over current.
When the full power switch is in the 120 volt (up) position,
you can take up full rated power of the generator at 120
volts from the single duplex receptacle, single locking type
120 volt receptacle, or a combination of these receptacles
as long as the total load does not exceed the generating set
capacity.
z
During use it detects when there is defective insulation
on the load side and breaks the circuit in response.
Idle Control Switch (both 60 and 180 Hz)
The unit is provided with an automatic idle control for noise
suppression and fuel cost reduction. The automatic idle
control automatically engages under a no-load condition.
With the automatic idle control switched “ON”, the engine
revolutions will automatically drop to about 2500 rpm (low-
speed operation) within 3 seconds after the load stops.When
the operation is resumed, the engine speed is automatically
increased to about 3600 rpm (high-speed operation) as soon
as the load is connected.
Figure 2. 120 V Simplified Diagram (Switch Up)
Fuel Gauge
NOTE
The fuel gauge is located on the fuel tank and allows easy
monitoring of the fuel level.
When the switch is in the 120 V position, the
locking type 240 volt receptacle cannot be used.
ACVoltmeter
This voltmeter indicates output voltage for both 60 and 180
Hz phases. In addition this voltmeter can also be used as a
diagnostic tool.
When the switch is in the 240 volt (down) position, you can
take up to half of the rated power of the generating set at
120 volts from the duplex receptacle and up to half of the
rated power of the set at 120 volts from the locking type 120
volt receptacle; or full rated power of the set at 240 volts
from the locking type 240 volt receptacle.
If the voltmeter indicator (needle) is elow the rated voltage,
engine problems may exist (low/high RPM's). To prevent
damage to the generator or power tools turn the generator
OFF and consult your authorized Multiquip service dealer.
Figure 3. 120/240V Simplified Diagram (Sw Dn.)
PAGE 14 — GDP-5000H A.C. GENERATOR— OPERATION AND PARTS MANUAL — REV. #2 (07/23/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
GDP-5000H — LOAD APPLICATION
Single Phase Load — 60 Hz
CAUTION:
Motors and motor-driven equipment draw
much greater current for starting than
during operation.
Always be sure to check the nameplate on the generator
and equipment to insure the wattage, amperage and
frequency requirements are satisfactorily supplied by the
generator for operating the equipment.
Generally, the wattage listed on the nameplate of the
equipment is its rated output. Equipment may require 130—
150% more wattage than the rating on the nameplate, as
the wattage is influenced by the efficiency, power factor and
starting system of the equipment.
An inadequate size connecting cable which cannot carry
the required load can cause a voltage drop which can burn
out the appliance or tool and overheat the cable.
The idle control is operated at minimum load capacity of
100W. If the load capacity is less than 100W, throw the idle
control switch to the OFF position.
NOTE
If wattage is not given on the equipment's
name plate, approximate wattage may be
determined by multiplying nameplate
voltage by the nameplate amperage.
CAUTION:
Before connecting this generator to any
building’s electrical system, a licensed
electrician must install an isolation
(transfer) switch. Serious injury or death
may result without this transfer switch.
WATTS = VOLTAGE x AMPERAGE
To determine the running wattage for your load, multiply the
running wattage as indicated by steps 1, 2, and 3 below:
Three Phase Load — 180 Hz
180 cycle, three phase, 230V, motor-in-head vibrators can
be operated with this generator. When operating more than
one concrete vibrator, the ON/OFF switch of each concrete
vibrators shall be turned on one at a time.
1. INCANDESCENT LOADS
Lights, heaters and similar appliances.
Total the running wattage and multiply by 1.
Example:
If they are switched on simultaneously, the circuit breaker
may trip or the engine may be overloaded.
29 light bulbs @ 100W each = 2.9 KW
use a 3 KW generator.
2. SMALL MOTORS
NOTE
Drills and other small power tools.
Total the running wattage and multiply by 2.
Example:
A 1 inch drill runs at 1 KW
use a 2 KW generator.
If output (kVA) is not given on the vibrators
nameplate, approximate output may be
determined by multiplying voltage by
amperage by
3. LARGE MOTORS
Submersible pumps, table saws etc.
Total the running wattage and multiply by 3.
Example:
A conveyor belt runs at 8 KW
use a 24 KW generator.
GDP-5000H A.C. GENERATOR — OPERATION AND PARTS MANUAL — REV. #2 (07/23/08) — PAGE 15
Download from Www.Somanuals.com. All Manuals Search And Download.
GDP-5000H — LOAD APPLICATION
WARNING:
CAUTION:
Before connecting this generator to any
building’s electrical system, a licensed
electrician must install an isolation
(transfer) switch.
z
z
z
z
Always use a vibrator with short circuit
protection.
Always use rubber boots and gloves
when operating the vibrator.
Serious injury or death may result without
this transfer switch.
Use adequate size connecting cable
for extension.
How to Use
Maintain electrical cords in good
condition and frequently replace the
entire cable of the vibrator with a new
one.
Always conduct the following in order that the earth leakage
breaker will operate safely. Also, if the leakage breaker should
for some reason actuate, first stop the generator and then
repair or eliminate the source of the earth leakage before
resetting the leakage breaker.When setting up the generator
perform the following:
Earth Leakage Breaker (180 Cycle)
The 180 Hz leakage breaker (Figure 4) is an earth leakage
breaker, so please use it after carefully reading the following:
Ground the Generator
Ground the generator from its ground connector so that
resistance to ground is 500 ohms or less.
Ground the Tool
Ground the tool (load) in the same manner as the generator.
NOTE
Simply because the generator is equipped
with a earth leakage breaker does not mean
that grounding of the load can be neglected,
please be sure to properly ground load
equipment.
Figure 4. Earth Leakage Breaker
Test Operation
For safety’s sake, the operation of the earth leakage breaker
should be tested periodically according to the following
procedure:
NOTE
1. Start the engine and set it to high speed.
2. Turn the leakage breaker ON.
Before operating generator press
earth leakage test button.
3. During normal operation, press the earth leakage indicator
test button on the front of the generator and observe
that indicator button pops out and the leakage breaker
trips.
The earth leakage breaker's earth leakage detection
sensitivity is 30 mA, and the actuation time is 0.1 sec.
4. Push the indicator button back in when resetting.
PAGE 16 — GDP-5000H A.C. GENERATOR— OPERATION AND PARTS MANUAL — REV. #2 (07/23/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
GDP-5000H — OPERATING INSTRUCTIONS
Warm up
Before Starting
1. When the engine starts, open the choke slowly.
1. Be sure to disconnect the electrical load and switch
both main circuit breakers (60 and 180 Hz) to the “OFF”
position prior to starting the engine.
2. Run the engine at low speed for 3 minutes without load
until the engine warms up.
2. Never start the engine with the main circuit breaker“ON”.
3. Turn the idle control switch to the "OFF" (down) position
and check the voltage by referring to the voltmeter on
the control box.
3. Check the lubricating oil level prior to starting the engine.
Make sure the generator is level. The oil level must be
maintained between two notches on the dipstick.
CAUTION:
4. When there is not enough lubricating oil, fill the crankcase
with high grade motor oil. Use a high quality detergent
oil classified SC, SD or SE. (See Table 4 on page 13)
DO NOT change the engine speed control
lever which has been set at the factory prior
to shipping.
CAUTION:
z
NEVER start the engine when the oil level
is below the lower mark on the dipstick.
1. Check the generator for abnormal noise and smells.Then
connect the load to the receptacles of the generator.
z
Check the fuel level on the fuel gauge.
When fuel is low, fill the fuel tank with
clean fresh unleaded automotive gasoline.
2. Switch both main circuit breakers (60 and 180 Hz) to
the “ON” position and turn the idle control switch to the
“ON” (down) position for normal (load) engine operation.
z
If gasoline spillage occurs, completely
wipe up the spilled gasoline.
Operation
Check the voltage by referring to the voltmeter on the control
box. When the voltmeter indicates 120 volts, 120 volts from
the 120V receptacles and 240 volts from the 240V receptacle
can be obtained at the same time. Refer to Figure 1, Controls
and Indicators, item 7 on page 10.
Starting
1. Open the fuel cock located below the fuel tank.The fuel
starts to flow when the fuel cock is turned downward.
2. Place the idle control switch in the “ON” (up) position.
3. Close the choke. Adjust the opening of the choke valve
according to operating conditions. When the engine is
warm or the air temperature is high, close the choke
valve halfway or open it all the way.
Stopping the Engine
CAUTION:
4. Confirm that both main circuit breakers (60 and 180 Hz)
on the generator control box are in the “OFF” position.
NEVER stop the engine suddenly while
running at high speeds.
5. Set the operation switch to the “ON” position and grasp
the starting knob and slowly pull it out. The resistance
becomes hardest at a certain position, corresponding
to the compression point. Rewind the rope a little from
that point and pull out sharply.
1. Remove the load from the generator. Place the circuit
breaker in the “OFF” position (See Figure. 3 on page 9).
Run the engine (no-load) with the idle control switch set
to the ON position for three to five minutes, then stop
the engine.
6. If the engine fails to start, repeat the procedure.
CAUTION:
2. Turn the START/STOP switch to the “STOP” position.
z
z
DO NOT pull the starter rope all the way
to the end.
3. Never stop the engine suddenly while running at high
speed.
DO NOT release the starter rope after
pulling. Allow it to rewind as soon as
possible.
4. After the engine has stopped, close the fuel cock.
GDP-5000H A.C. GENERATOR — OPERATION AND PARTS MANUAL — REV. #2 (07/23/08) — PAGE 17
Download from Www.Somanuals.com. All Manuals Search And Download.
GDP-5000H — MAINTENANCE
General Inspection
Service Daily
At least daily or prior to each use, the generating set should
be cleaned and inspected for deficiencies. Check for loose,
missing or damaged nuts, bolts or other fasteners. Also check
for fuel or oil leaks.
If engine is operating in very dusty and dry grass conditions.
A clogged air cleaner will result in high fuel consumption,
loss of power and excessive carbon build-up in the
combustion chamber.
Engine Side (Refer to the Engine Instruction Manual)
Cleaning the Fuel Strainer
Check Oil Level
Clean the fuel strainer if it contains dust or water. Remove
dust or water in the strainer cap and wash it in gasoline.
Securely fasten the fuel strainer cap so that fuel will not
leak. Check the fuel strainer every 200 hours of operation or
once a month.
Check the crankcase oil level prior to each use, or when the
fuel tank is filled. Make sure the generating set is level. The
oil level must be between the two notches on the dipstick.
Changing Oil
Spark Plug
Change oil after the first 20 hours of operation. Drain and
refill the engine crankcase every 50 operating hours or once
a week thereafter.Drain crankcase oil into a suitable container
while engine is still warm.Replace the drain plug tightly.Add
oil through the filler hole.
Remove carbon build-up on the spark plug (Figure 5) with a
wire brush. Set the spark plug gap to 0.6—0.7 mm (0.024-
0.028 inch).Tighten with a spark plug socket wrench. Clean
the spark plug every 50 operating hours or once a week.
Air Cleaner
Every 50 hours: Remove air cleaner element (std. or heavy
duty types), and wash in kerosene or liquid detergent and
hot water.Wrap foam element in a cloth and squeeze dry.Wipe
heavy duty paper element dry with toweling. Saturate element
with kerosene; squeeze excess from foam element. Wipe
excess from heavy duty paper element.
Figure 5. Spark Plug Gap
PAGE 18 — GDP-5000H A.C. GENERATOR— OPERATION AND PARTS MANUAL — REV. #2 (07/23/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
GDP-5000H — PREPARATION FOR LONG -TERM STORAGE
Generator Storage
For storage of the generating set for over 30 days, the
following is required:
z
z
Drain the fuel tank completely.
Run the engine until the gasoline in the carburetor is
completely consumed.
z
z
z
z
Completely drain the oil from the crankcase and refill
with fresh oil.
Remove the spark plug, pour 2 or 3 cc of SAE 30 oil
into the cylinder and crank slowly to distribute the oil.
Slowly rotate the engine a few times with the starter
Rope and install a new plug.
Pull out the starter rope slowly and stop at the
compression point.
z
z
Clean all external parts of the generating set with a cloth.
Cover the generating set and store in a clean, dry place.
GDP-5000H A.C. GENERATOR — OPERATION AND PARTS MANUAL — REV. #2 (07/23/08) — PAGE 19
Download from Www.Somanuals.com. All Manuals Search And Download.
GDP-5000H —WIRING DIAGRAM
PAGE 20 — GDP-5000H A.C. GENERATOR— OPERATION AND PARTS MANUAL — REV. #2 (07/23/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
GDP-5000H —TROUBLESHOOTING (ENGINE)
diagnosis based on the Engine Troubleshooting (Table 6)
information shown below and on the proceeding page. If the
problem cannot be remedied, please leave the unit just as it
is and consult our company's business office or service
plant.
Practically all breakdowns can be prevented by proper
handling and maintenance inspections, but in the event of a
breakdown, please take a remedial action following the
TABLE 6. ENGINE TROUBLESHOOTING
SYMPTOM
POSSIBLE PROBLEM
SOLUTION
Inspect carburetor to see if fuel
is reaching it?
Check fuel line
No Fuel?
Add Fuel
Water in fuel tank?
Fuel filter clogged?
Stuck carburetor?
Spark plug is black?
Flush or replace fuel tank.
Replace fuel filter
Check float mechanism.
Poor starting
(Engine will not start)
Spark plug is fouled. Check tranistor ignition unit.
Insufficient compression, injected air leaking. Carburetor jets are
clogged (overflow).
Spark plug is blue-white?
No spark present at tip of spark
plug?
Tranistor ignition unit broken, high voltage cord cracked or broken.
Start/Stop switch broken. Replace spark plug if fouled.
No oil?
Add oil as required.
Low oil or oil pressure shutdown
sensor is defective?
Check oil level, add oil if necessary. Check automatic oil shutdown
circuit "oil sensor" Replace oil sensor.
Engine will not turn over?
Replace cylinder and piston and if necessary axel joint.
Tighten cylinder head connecting bolts.
Cylinder head connecting bolts
loose?
Cylinder head gasket damaged?
Malfunction of valve seat?
Spark plug is loose?
Replace cylinder head gasket.
Re-seat valves.
Insufficient power output "no
compression"
Replace spark plug.
Replace piston rings.
Worn piston rings?
Malfunction in air-cleaner system,
air filter clogged?
Clean or replace air filter.
Air leaking in from interface
between carburetor and cylinder
head?
Tighten bolts between carburetor and cylinder head. Replace
cylinder head gasket.
Insufficient power output
"compression"
Clean or replace fuel filter.
Clean or replace carburetor.
Check carburetor float.
Malfunction in fuel system?
GDP-5000H A.C. GENERATOR — OPERATION AND PARTS MANUAL — REV. #2 (07/23/08) — PAGE 21
Download from Www.Somanuals.com. All Manuals Search And Download.
GDP-5000H —TROUBLESHOOTING (ENGINE)
TABLE 6. ENGINE TROUBLESHOOTING (CONTINUED)
SYMPTOM
POSSIBLE PROBLEM
Malfunction in cooling fan?
Air in-take filter clogged?
SOLUTION
Check or replace cooling fan.
Insufficient power output
"compression" and overheats
Clean or replace air in-take filter.
Over accumulation of exhaust
products?
Clean and check valves.
Check muffler, replace if necessary.
Burns to much fuel
Wrong spark plug?
Replace spark plug with manufactures suggested type spark plug.
Lubricating oil is wrong viscosity? Replace lubricating oil with correct viscosity.
Exhaust color is continiously
"WHITE"
Worn rings?
Replace rings
Air cleanner clogged?
Clean or replace air cleaner.
Adjust choke valve to the correct position.
Choke valve has not been set to
the correct position?
Exhaust color is continiously
"BLACK"
Carburetor defective, seal on
carburetor broken?
Replace carburetor or seal.
Adjust carburetor.
Poor carburetor adjustment
"engine runs too rich?
PAGE 22 — GDP-5000H A.C. GENERATOR— OPERATION AND PARTS MANUAL — REV. #2 (07/23/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
GDP-5000H —TROUBLESHOOTING (GENERATOR)
diagnosis based on the GeneratorTroubleshooting (Table 7)
information shown below and on the preceding page. If the
problem cannot be remedied, please leave the unit just as it
is and consult our company's business office or service
plant.
Practically all generator breakdowns can be prevented by
proper handling and maintenance inspections, but in the event
of a breakdown, please take a remedial action following the
TABLE 7. GENERATOR TROUBLESHOOTING
SYMPTOM
Low voltage
POSSIBLE PROBLEM
Engine speed too low?
SOLUTION
Raise engine speed to rated RPM.
AC voltmeter not working?
Replace Ac voltmeter.
Control box internal wiring
malfunction?
Check control box wiring.
Defective ignition coil?
Check red and green ignition wires. Replace ignition wires if
necessary.
Low voltage. Engine speed
normal 3650 RPM (unloaded),
2500 RPM (idle)
Rotor winding malfunction?
Stator winding malfunction?
Leakage breaker malfunction?
Full power switch malfunction?
Engine speed too high?
Check or replace rotor.
Check or replace stator.
Check or replace CB1 or CB2.
Check full power switch and full power switch circuit.
Lower engine speed to rated RPM.
Check control box wiring.
Voltage output too high.
Voltage output too high. Engine
speed normal 3650 RPM
(unloaded), 2500 RPM (idle)
Control box internal wiring
malfunction
Circuit breaker will not turn on
"NO LOAD"
Defective circuit breaker?
Replace circuit breaker.
Overloaition?
Reduce load or replace breaker.
Check load circuit for short.
Check solenoid.
Circuit breaker will turn on
"LOADED" but trips immediately.
Load circuit is shorted?
Stuck solenoid?
Does not accelerate from low to
high "NO LOAD"
Bad Idle control switch?
Idle control switch malfunction?
Check or replace idle control switch.
Check or replace idle control switch.
Does not accelerate from low to
high "LOAD ACTIVE"
Idle control device malfunction?
Check or replace idle control device.
Check control box wiring.
Control box interal wiring
defective?
GDP-5000H A.C. GENERATOR — OPERATION AND PARTS MANUAL — REV. #2 (07/23/08) — PAGE 23
Download from Www.Somanuals.com. All Manuals Search And Download.
GDP-5000H —TROUBLESHOOTING (GENERATOR)
TABLE 7. GENERATOR TROUBLESHOOTING (CONTINUED)
SYMPTOM
POSSIBLE PROBLEM
Defective rotor windings?
Defective solenoid?
SOLUTION
Check or replace rotor.
Check or replace solenoid.
Does not decelerate no
"VOLTAGE OUTPUT".
Defective idle control device?
Defective solenoid?
Check or replace idle control device.
Check or replace idle control device.
Check control box wiring, replace any defective components.
Check or replace solenoid.
Control box wiring malfunction?
Defective solenoid?
Does not decelerate but has
"VOLTAGE OUTPUT".
Idle control device malfunction?
Check or replace idle control device.
PAGE 24 — GDP-5000H A.C. GENERATOR— OPERATION AND PARTS MANUAL — REV. #2 (07/23/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
GDP-5000H A.C. GENERATOR — OPERATION AND PARTS MANUAL — REV. #2 (07/23/08) — PAGE 25
Download from Www.Somanuals.com. All Manuals Search And Download.
GDP-5000H — EXPLANATION OF CODE IN REMARKS COLUMN
The following section explains the different symbols and
QTY. Column
remarks used in the Parts section of this manual. Use the help
numbers found on the back page of the manual if there are any
questions.
Numbers Used - Item quantity can be indicated by a
number, a blank entry, or A/R.
A/R (As Required) is generally used for hoses or other parts
that are sold in bulk and cut to length.
The contents and part numbers listed in the parts section are
subject to change without notice. Multiquip does not
guarantee the availibility of the parts listed.
A blank entry generally indicates that the item is not sold
separately. Other entries will be clarified in the “Remarks”
Column.
REMARKS Column
Sample Parts List:
Some of the most common notes found in the “Remarks”
Column are listed below. Other additional notes needed to
describe the item can also be shown.
NO. PART NO. PART NAME
QTY. REMARKS
1
2
2
3
4
12345
BOLT ...................... 1 ......INCLUDES ITEMS W/
WASHER, 1/4 IN. .............NOT SOLD SEPARATELY
WASHER, 3/8 IN. ... 1 ......MQ-45T ONLY
HOSE ................... A/R ....MAKE LOCALLY
BEARING ............... 1 ......S/N2345B AND ABOVE
*
*
*
12347
12348
12349
Assembly/Kit - All items on the parts list with the same
unique symbol will be included when this item is purchased.
Indicated by:
“INCLUDES ITEMS W/(unique symbol)”
NO. Column
Unique Symbols - All items with same unique symbol
Serial Number Break - Used to list an effective serial
number range where a particular part is used.
( , #,
+
, %, or >) in the number column belong to the same
*
assembly or kit, which is indicated by a note in the “Remarks”
column.
Indicated by:
“S/N XXXXX AND BELOW”
“S/N XXXX AND ABOVE”
“S/N XXXXTO S/N XXX”
Duplicate Item Numbers - Duplicate numbers indicate
multiple part numbers are in effect for the same general
item, such as different size saw blade guards in use or a
part that has been updated on newer versions of the same
machine.
Specific Model Number Use - Indicates that the part is
used only with the specific model number or model number
variant listed. It can also be used to show a part is NOT
used on a specific model or model number variant.
When ordering a part that has more than one
item number listed, check the remarks column
for help in determining the proper part to order.
Indicated by:
“XXXXX ONLY”
“NOT USED ON XXXX”
“Make/Obtain Locally” - Indicates that the part can be
purchased at any hardware shop or made out of available
items. Examples include battery cables, shims, and certain
washers and nuts.
PART NO. Column
Numbers Used - Part numbers can be indicated by a
number, a blank entry, orTBD.
“Not Sold Separately” - Indicates that an item cannot be
purchased as a separate item and is either part of an
assembly/kit that can be purchased, or is not available for
sale through Multiquip.
TBD (To Be Determined) is generally used to show a part
that has not been assigned a formal part number at time of
publication.
A blank entry generally indicates that the item is not sold
separately or is not sold by Multiquip. Other entries will be
clarified in the “Remarks” Column.
PAGE 26 — GDP-5000H A.C. GENERATOR— OPERATION AND PARTS MANUAL — REV. #2 (07/23/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
GDP-5000H — SPARE PARTS LIST
GDP-5000H 1 TO 3 UNITS WITH HONDA
GX340K1 ENGINE
1 to 3 Units
Qty.
4
P/N .............................Description
0601812597..............RECEPTACLE
0601830737 ..............SWITCH FULL POWER
0601830738 ..............SWITCH OPERATION
06011830727............SWITCH IDLE CONTROL
0601807480 ..............CIRCUIT BREAKER
0601802651 ..............CIRCUIT BREAKER
0602125031 ..............FUEL GAUGE
0810106004..............CAP FUEL TANK
0810107103 ..............FILTER FUEL
4
1
2
1
2
1
1
1
1
3015419604..............SHOCK MOUNT
1665419004 ..............SHOCK MOUNT
16950ZB4015 ...........FUEL COCK
9807955846..............SPARK PLUG
15510ZE2043 ...........OIL SENSOR
15600735003............CAP OIL FILLER
28400ZE3W01ZB.....RECOIL ASSY.
17211899000............ELEMENT AIR CLEANER
16100ZE3F11...........CARBURETOR ASSY.
4
1
1
1
1
2
2
1
NOTE
Part numbers on this Suggested
Spare Parts List may supercede/
replace the P/N shown in the text
pages of this book.
GDP-5000H A.C. GENERATOR — OPERATION AND PARTS MANUAL — REV. #2 (07/23/08) — PAGE 27
Download from Www.Somanuals.com. All Manuals Search And Download.
GDP-5000H — ENGINE/GENERATOR ASSY.
ENGINE\GENERATORASSY.
PAGE 28 — GDP-5000H A.C. GENERATOR— OPERATION AND PARTS MANUAL — REV. #2 (07/23/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
GDP-5000H — ENGINE/GENERATOR ASSY.
ENGINE\GENERATORASSY.
NO
PART NO
PART NAME
QTY
REMARKS
1
2
3
4
5
6
GENERATOR ASSEMBLY
CONTROL BOX ASSEMBLY
1
1
1
1
1
1
SEE PAGE 29-30
SEE PAGE 31-32
SEE PAGE 40-73
SEE PAGE 34-35
SEE PAGE 36-37
SEE PAGE 38
GX340K1EDN2 ENGINE, HONDA
7852310003
7855413204
MUFFLER ASSEMBLY
PIPE FRAME ASSEMBLY
NAME PLATE AND DECALS
GDP-5000H A.C. GENERATOR — OPERATION AND PARTS MANUAL — REV. #2 (07/23/08) — PAGE 29
Download from Www.Somanuals.com. All Manuals Search And Download.
GDP-5000H — GENERATOR ASSY.
GENERATORASSY.
PAGE 30 — GDP-5000H A.C. GENERATOR— OPERATION AND PARTS MANUAL — REV. #2 (07/23/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
GDP-5000H — GENERATOR ASSY.
GENERATORASSY.
NO
1
PART NO
PART NAME
QTY.
REMARKS
7851000203
ROTOR ASSY............................. 1 .....................INCLUDES ITEM W/
*
1-1
1-2
1-3
1-4
1-5
2
FIELD ASSY ................................ 1 .....................NOT SOLD SEPERATELY
ARMATURE EXCITER................ 1 .....................NOT SOLD SEPERATELY
RECTIFIER ................................. 1 .....................S10VB60
*
*
*
*
*
0601820037
0601822640
0071206304
7851017204
0801086104
030210250
7851341203
7851315502
011208025
7851315402
7851350003
011606025
1961319004
1961313003
0011305100
7851334204
7851316804
031108160
030208200
7851331103
0310300090
001305100
SURGE ABSORBER .................. 1 .....................TNR15G471K
BEARING
SET BOLT ROTOR
SET WASHER
1
1
1
3
4
SPRING WASHER ...................... 1 .....................REPLACES 0040010000
5
ARMATURE ASSY
END BRACKET
1
1
6
7
BOLT HEX HEAD ........................ 4 .....................REPLACES 0017108025
8
END BRACKET
FIELD ASSY EXCITER
1
1
9
10
11
12
13
14
15
16
17
18
19
20
BOLT HEX HEAD ........................ 4 .....................REPLACES 0017106025
GROMMET
GUIDE PANEL AIR
1
1
BOLT HEX HEAD ........................ 4 .....................REPLACES 0017105012
COVER
SET BOLT STATOR
1
4
SPRING WASHER ...................... 4 .....................REPLACES 0041208000
PLAIN WASHER.......................... 4 .....................REPLACES 0040008000
COVER
SEAL
1
1
BOLT HEX HEAD ........................ 4 .....................REPLACES 0017105012
GDP-5000H A.C. GENERATOR — OPERATION AND PARTS MANUAL — REV. #2 (07/23/08) — PAGE 31
Download from Www.Somanuals.com. All Manuals Search And Download.
GDP-5000H — CONTROL BOX ASSY.
CONTROL BOXASSY.
PAGE 32 — GDP-5000H A.C. GENERATOR— OPERATION AND PARTS MANUAL — REV. #2 (07/23/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
GDP-5000H — CONTROL BOX ASSY.
CONTROLBOXASSY.
NO
1
PART NO
PART NAME
CONTROL BOX
GROMMET
QTY.
1
1
REMARKS
7851810203
0601850220
0601823853
0027204010
0030004000
0601823204
0027203016
0601842415
0027204008
7851820212
0601800267
0601802651
4341817004
0021004010
0601811032
0601811031
0601812597
0021004010
0030004000
0601830737
0601832005
0601802937
0021004070
0030004000
0601812594
0021004010
0030004000
0601830738
0601830727
0601832005
0601815109
0601815465
0027204020
0601820083
0027204020
0017105010
0017106016
011206020
2
3
4
IDLE CONTROL UNIT ................1..........ND-80
MACHINE SCREW
2
NUT HEX .....................................2..........REPLACES 0207004000
RECTIFIER ..................................4..........S5VB60
5
6
MACHINE SCREW
4
7
RESISTOR ..................................1..........GG40W 7 ohms
8
MACHINE SCREW
CONTROL PANEL
2
1
9
10
11
12
13
14
15
16
17
AC VOLTMETER .........................1..........REPLACES 0601800279
CIRCUIT BREAKER ....................1..........KM-2 250V 15A
BRACKET
MACHINE SCREW
RECEPTACLE
1
2
1
RECEPTACLE .............................1..........REPLACES 0601811035
RECEPTACLE
MACHINE SCREW
1
6
NUT HEX .....................................6..........REPLACES 0207004000
18
19
20
21
FULL POWER SWITCH
1
CAP ..............................................1..........REPLACES 0601832006
CIRCUIT BREAKER ....................1..........EY-33C 230V 12.5A 30mA
MACHINE SCREW
2
NUT HEX .....................................2..........REPLACES 0207004000
22
23
RECEPTACLE
MACHINE SCREW
1
6
NUT HEX .....................................6..........REPLACES 0207004000
24
25
26
27
28
29
30
31
32
33
34
OPERATION SWITCH
1
1
IDLE CONTROL SWITCH
CAP ..............................................2..........REPLACES 0601832006
GROUNDING TERMINAL
TERMINAL BOARD
MACHINE SCREW
1
1
2
RECTIFIER ..................................3..........S25VB60
MACHINE SCREW
BOLT HEX HEAD
BOLT HEX HEAD
3
6
3
BOLT HEX HEAD ........................1..........REPLACES 0017106020
WIRE HARNESS
35
7850296000
1
GDP-5000H A.C. GENERATOR — OPERATION AND PARTS MANUAL — REV. #2 (07/23/08) — PAGE 33
Download from Www.Somanuals.com. All Manuals Search And Download.
GDP-5000H — MUFFLER ASSY.
MUFFLERASSY.
PAGE 34 — GDP-5000H A.C. GENERATOR— OPERATION AND PARTS MANUAL — REV. #2 (07/23/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
GDP-5000H — MUFFLER ASSY.
MUFFLERASSY.
NO
1
PART NO
PART NAME
MUFFLER
PROTECTOR
PROTECTOR
SEAL
QTY.
REMARKS
7852310003
18320ZC2000
18325ZB4000
18329ZB4000
18355ZB4630
90183671003
0105050616
18333ZB4800
957000802000
7855469004
011008020
1
1
1
2
1
1
2
3
4
5
ARRESTOR
TAPPING SCREW
BOLT HEX HEAD ...................... 5 ......... REPLACES 0017106012
6
7
8
GASKET
BOLT HEX HEAD
BRACKET
1
2
1
9
10
11
12
13
14
15
BOLT HEX HEAD ...................... 1 ...........REPLACES 0017108020
BOLT HEX HEAD ...................... 1 ...........REPLACES 0017108020
011008020
7905469004
011206020
BRACKET
1
BOLT HEX HEAD ...................... 1 ...........REPLACES 0017106020
BOLT HEX HEAD ...................... 4 ...........REPLACES 0017106012
0105050616
1
1
7852310003
FFLER
1
GDP-5000H A.C. GENERATOR — OPERATION AND PARTS MANUAL — REV. #2 (07/23/08) — PAGE 35
Download from Www.Somanuals.com. All Manuals Search And Download.
GDP-5000H — PIPE FRAME ASSY.
PIPE FRAME ASSY.
PAGE 36 — GDP-5000H A.C. GENERATOR— OPERATION AND PARTS MANUAL — REV. #2 (07/23/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
GDP-5000H — PIPE FRAME ASSY.
PIPE FRAME ASSY.
NO
1
PART NO
PART NAME
PIPE FRAME
BRACKET
QTY.
1
1
REMARKS
7855410202
7855413204
011106015
7855411203
3015419604
020108060
1665419004
020108060
011208030
0017108045
020108060
7915455103
7855455003
0017106016
7915456004
0017106016
7905512002B
0810106004
0810107103
0602125031
7855525514
7855525604
011208030
011008020
16950ZB4015
950014521040
0605515096
2
3
BOLT HEX HEAD ...................... 3 ............ REPLACES 0017106015
4
BASE
1
2
5
RUBBER SUSPENSION
6
NUT HEX ................................... 4 ............ REPLACES 0207008000
RUBBER SUSPENSION ........... 2 ............ REPLACES 1725419214
NUT HEX ................................... 4 ............ REPLACES 0207008000
BOLT HEX HEAD ...................... 2 ............ REPLACES 0017108030
7
8
9
10
BOLT HEX HEAD
2
NUT HEX ................................... 2 ............ REPLACES 0207008000
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
COVER
COVER
1
1
6
1
2
BOLT HEX HEAD
STOPPER
BOLT HEX HEAD
FUEL TANK................................ 1 ............ REPLACES 7905512002
CAP FUEL TANK
FUEL FILTER
FUEL GAUGE
RUBBER CUSHION
COLLAR
1
1
1
2
2
BOLT HEX HEAD ...................... 2 ............ REPLACES 0017108030
BOLT HEX HEAD ...................... 2 ............ REPLACES 0017108020
FUEL COCK .............................. 1 ............ SEE PAGE 70 FOR COMPONENTS
HOSE
HOSE BAND
1
2
GDP-5000H A.C. GENERATOR — OPERATION AND PARTS MANUAL — REV. #2 (07/23/08) — PAGE 37
Download from Www.Somanuals.com. All Manuals Search And Download.
GDP-5000H — NAMEPLATE AND DECALS.
NAMEPLATE AND DECALS
PAGE 38 — GDP-5000H A.C. GENERATOR— OPERATION AND PARTS MANUAL — REV. #2 (07/23/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
GDP-5000H — NAMEPLATE AND DECALS.
NAMEPLATE AND DECALS
NO
PART NO
PART NAME
QTY.
REMARKS
1
2
3
4
5
6
7
8
9
0820610804
0820610404
7900636004
7900638204
8700611804
8700611904
0800628504
7850630003
DECAL: CAUTION ..................... 1 ...........DCS01
DECAL: WARNING! ................... 1 ...........S-3627
DECAL: 3600 RPM ONLY.......... 1 ...........S-4461
DECAL: OPER. INSTRUC. ........ 1 ...........S-4607
DECAL: WARNING! ................... 1 ...........S-4984
DECAL: DANGER! ..................... 1 ...........S-4985
DECAL: GROUND ..................... 1 ...........S-1123
DECAL: GDP-5000H ................. 1 ...........S-5059
NAMEPLATE
1
ORDER FROM MULTIQUIP SERVICE DEPT. BY
MODEL & SERIAL NUMBER
10
1980680004
DECAL: FUEL COCK ................ 1 ...........S-3704
SEE PAGE 7 FOR DECAL ILLUSTRATIONS
GDP-5000H A.C. GENERATOR — OPERATION AND PARTS MANUAL — REV. #2 (07/23/08) — PAGE 39
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX340K1 ENGINE — CYLINDER HEAD
CYLINDER HEADASSY.
PAGE 40 — GDP-5000H A.C. GENERATOR— OPERATION AND PARTS MANUAL — REV. #2 (07/23/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX340K1 ENGINE — CYLINDER HEAD
CYLINDER HEADASSY.
NO
1
PART NO
PART NAME
QTY.
REMARKS
122AOZF6W00
12204ZE2325
12205ZE2315
12216ZE2300
12251ZE3W00
12310ZE2010
12391ZE2010
18330ZE3700
18333ZE3800
90014ZE2000
90042ZE3700
90047ZE2000
90441ZE2010
9405008000
9430112200
957251008000
9807955846
9807955855
HEAD COMP., CYLNDER ...........1.......... INCLUDES ITEM W/
*
2
GUIDE, IN. VALVE (OVER SIZE) 1
*
*
3
GUIDE, EX. VALVE (OVER SIZE) 1
*
4
CLIP, VALVE GUIDE
GASKET, CYLINDER HEAD
COVER COMP., HEAD
PACKING, HEAD COVER
PIPE, EX.
2
1
1
1
1
1
1
2
2
5
6
7
8
9
GASKET, EX. PIPE
BOLT, HEAD COVER
BOLT, STUD, 8X98
BOLT, STUD, 8X47
10
11
12
13
14
15
16
17
WASHER COMP., HEAD COVER 1
NUT, FLANGE, 8MM
2
2
4
1
PIN, DOWEL, 12X20
BOLT, FLANGE, 10X80
PLUG, SPARK (BPR5ES NGK)
PLUG, SPARK (W16EPRU ND) 1
1
GDP-5000H A.C. GENERATOR — OPERATION AND PARTS MANUAL — REV. #2 (07/23/08) — PAGE 41
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX340K1 ENGINE — RECOIL STARTER
RECOIL STARTERASSY.
PAGE 42 — GDP-5000H A.C. GENERATOR— OPERATION AND PARTS MANUAL — REV. #2 (07/23/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX340K1 ENGINE — RECOIL STARTER
RECOILSTARTERASSY.
NO
1
PART NO
PART NAME
QTY.
1
REMARKS
INCLUDES ITEMS W/
28400ZE3W01ZB
28410ZE3W01ZB
28421ZE3W01
28422ZE2W01
28441ZE2W01
28442ZE2W01
28443ZE2W01
28444ZE2W01
28445ZE2W01
28461ZE2W01
28462ZE3W01
28469ZE2W01
90004ZE2W01
957010600800
STARTER ASSY, RECOIL
CASE COMP., RECOIL STARTER
PULLEY, RECOIL STARTER
RATCHET, STARTER
SPRING, FRICTION
SPRING, STARTER RETURN
SPRING, RATCHET
RETAINER, SPRING
HOLDER, SPRING
GRIP, STARTER
*
2
1
*
3
1
*
4
2
*
5
1
*
6
1
*
7
2
*
8
1
*
9
1
*
10
1
*
11
12
13
14
ROPE, RECOIL STARTER
GRID REINFORCEMENT
SCREW, CENTER
1
*
*
*
1
1
BOLT, FLANGE, 6X8
3
GDP-5000H A.C. GENERATOR — OPERATION AND PARTS MANUAL — REV. #2 (07/23/08) — PAGE 43
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX340K1 ENGINE — FAN COVER
FAN COVER ASSY.
PAGE 44 — GDP-5000H A.C. GENERATOR— OPERATION AND PARTS MANUAL — REV. #2 (07/23/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX340K1 ENGINE — FAN COVER
FAN COVER ASSY.
NO
1
PART NO
PART NAME
COVER COMP., FAN
SHROUD
GROMMET, DRAIN HOLE
BOLT, FLANGE, 6X12
CLIP
QTY.
REMARKS
19610ZE3700ZB
19631ZE3W00
81329567020
90013883000
90654SA4003
1
1
1
6
2
2
3
4
5
GDP-5000H A.C. GENERATOR — OPERATION AND PARTS MANUAL — REV. #2 (07/23/08) — PAGE 45
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX340K1 ENGINE — CAMSHAFT/VALVES
CAMSHAFT/VALVES ASSY.
PAGE 46 — GDP-5000H A.C. GENERATOR— OPERATION AND PARTS MANUAL — REV. #2 (07/23/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX340K1 ENGINE — CAMSHAFT/VALVES
CAMSHAFT/VALVES ASSY.
NO
1
PART NO
PART NAME
QTY.
REMARKS
14100ZE3010
14410ZE3013
14431ZE2000
14441ZE2000
14451ZE1003
14568ZE1000
14711ZE3000
14721ZE3000
14751ZE2003
14771ZE2000
14773ZE2000
14775ZE2010
14781ZE2000
14791ZE2010
90012ZE0010
90206ZE1000
CAMSHAFT ASSY. .............................. 1 ........ INCLUDES ITEMS/W
ROD, PUSH
*
2
2
2
2
2
1
1
1
2
1
1
2
1
1
2
2
3
ARM, VALVE ROCKER
LIFTER, VALVE
4
5
PIVOT, ROCKER ARM
SPRING, WEIGHT RETURN
VALVE, IN
6
*
7
8
VALVE, EX.
SPRING, VALVE
9
10
11
12
13
14
15
15
RETAINER, IN. VALVE SPRING
RETAINER, EX. VALVE SPRING
SEAT, VALVE SPRING
ROTATOR, VALVE
PLATE, PUSH ROD GUIDE
BOLT, PIVOT
NUT, PIVOT ADJUSTING
GDP-5000H A.C. GENERATOR — OPERATION AND PARTS MANUAL — REV. #2 (07/23/08) — PAGE 47
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX340K1 ENGINE — PISTON/RINGS
PISTON/RINGSASSY.
PAGE 48 — GDP-5000H A.C. GENERATOR— OPERATION AND PARTS MANUAL — REV. #2 (07/23/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX340K1 ENGINE — PISTON/RINGS
PISTON/RINGSASSY.
NO
PART NO
PART NAME
QTY. REMARKS
1
13010ZE3003
13011ZE3003
13012ZE3003
13013ZE3003
13101ZE3W00
13102ZE3W00
13103ZE3W00
13104ZE3W00
13111ZF6000
13200ZE3010
90001ZE8000
90601ZE3000
RING SET, PISTON (STD)
RING SET, PISTON (0.25)
RING SET, PISTON (0.50)
RING SET, PISTON (0.75)
PISTON (STD)
1
1
1
1
1
1
1
1
1
2
PISTON (0.25)
PISTON (0.50)
PISTON (0.75)
3
4
5
PIN, PISTON
ROD ASSY., CONNECTING ............ 1 .. INCLUDES ITEM W/
*
BOLT, CONNECTING ROD
CLIP, PISTON PIN, 18MM
2
2
*
6
GDP-5000H A.C. GENERATOR — OPERATION AND PARTS MANUAL — REV. #2 (07/23/08) — PAGE 49
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX340K1 ENGINE — AIR CLEANER
AIR CLEANERASSY.
PAGE 50 — GDP-5000H A.C. GENERATOR— OPERATION AND PARTS MANUAL — REV. #2 (07/23/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX340K1 ENGINE — AIR CLEANER
AIR CLEANERASSY.
NO
1
PART NO
PART NAME
TUBE BREATHER
ELEMENT, AIR CLEANER
SEPARATOR, AIR CLEANER
CASE COMP., AIR CLEANER
STAY, AIR CLEANER
QTY. REMARKS
1
15721ZB4000
17211899000
17212ZB4003
17220ZB4003
17222ZC2000
17231899000
17235899000
17236899000
17252899000
17367413690
9405005000
9405006000
2
1
1
1
1
1
2
2
1
1
6
3
3
4
5
6
COVER COMP., AIR CLEANER
CLIP A, AIR CLEANER WIRE
CLIP B, AIR CLEANER WIRE
SEAL, AIR CLEANER
7
8
9
10
11
12
FILTER, DRAIN TUBE
NUT, FLANGE, 5 MM
NUT, FLANGE, 6 MM
GDP-5000H A.C. GENERATOR — OPERATION AND PARTS MANUAL — REV. #2 (07/23/08) — PAGE 51
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX340K1 ENGINE — CYLINDER BARREL
CYLINDER BARREL ASSY. (RECOIL STARTER)
PAGE 52 — GDP-5000H A.C. GENERATOR— OPERATION AND PARTS MANUAL — REV. #2 (07/23/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX340K1 ENGINE — CYLINDER BARREL
CYLINDER BARREL ASSY. (RECOIL STARTER)
NO
PART NO
PART NAME
QTY. REMARKS
1
12000ZE3816
15510ZE2043
16541ZE3000
90131883000
90446KE1000
9410912000
91201ZE3004
91203952771
91353671004
9405010000
9425108000
957010601200
961006202000
BARREL ASSY., CYLINDER
SWITCH ASSY., OIL LEVEL
SHAFT, GOVERNOR ARM
BOLT, DRAIN PLUG
WASHER, 8.2X17X0.8
WASHER, DRAIN PLUG
OIL SEAL
1
1
1
2
1
2
1
1
1
1
1
2
1
2
3
4
5
6
7
8
OIL SEAL
ORING, 14 MM
9
10
11
12
13
NUT, FLANGE, 10 MM
PIN, LOCK, 8 MM
BOLT, FLANGE, 6X12
BEARING, RADIAL BALL 6202
GDP-5000H A.C. GENERATOR — OPERATION AND PARTS MANUAL — REV. #2 (07/23/08) — PAGE 53
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX340K1 ENGINE — CYLINDER BARREL
CYLINDER BARREL ASSY. (ELECTRIC START)
PAGE 54 — GDP-5000H A.C. GENERATOR— OPERATION AND PARTS MANUAL — REV. #2 (07/23/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX340K1 ENGINE — CYLINDER BARREL
CYLINDER BARREL ASSY. (ELECTRIC START)
NO
PART NO
PART NAME
QTY. REMARKS
1
12000ZE3826
15510ZE2043
16541ZE3000
90131883000
90446KE1000
9410912000
91201ZE300
91203952771
91353671004
9405010000
9425108000
957010601200
961006202000
BARREL ASSY., CYLINDER
SWITCH ASSY., OIL LEVEL
SHAFT, GOVERNOR ARM
BOLT, DRAIN PLUG
WASHER, 8.2X17X0.8
WASHER, DRAIN PLUG
OIL SEAL
1
1
1
2
1
2
1
1
1
1
1
2
1
2
3
4
5
6
7
8
OIL SEAL
ORING, 14 MM
9
10
11
12
13
NUT, FLANGE, 10 MM
PIN, LOCK, 8 MM
BOLT, FLANGE, 6X12
BEARING, RADIAL BALL 6202
GDP-5000H A.C. GENERATOR — OPERATION AND PARTS MANUAL — REV. #2 (07/23/08) — PAGE 55
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX340K1 ENGINE — CRANKCASE COVER/GOVERNOR
CRANKCASE COVER/GOVERNORASSY.
PAGE 56 — GDP-5000H A.C. GENERATOR— OPERATION AND PARTS MANUAL — REV. #2 (07/23/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX340K1 ENGINE — CRANKCASE COVER/GOVERNOR
CRANKCASE COVER/GOVERNORASSY.
NO
1+
PART NO
PART NAME
QTY. REMARKS
06165ZE3000
11300ZE3020
11381ZE3800
15600735700
15621896010
15625ZE1000
16510ZE3000
16511ZE8000
16512ZE3000
16513ZE2000
16531ZE2000
16520ZG4910
90473147000
90602ZE1000
91201ZE3004
9410106800
GOVERNOR KIT ..................................... 1 ...... INCLUDES ITEM W/*
COVER ASSY., CRANKCASE ................. 1 ...... INCLUDES ITEM W/+
2
3
PACKING, CASE COVER
1
4
CAP ASSY., OIL FILLER ......................... 1 ...... INCLUDES ITEM W/#
5
PACKING, OIL FILLER CAP
PACKING, OIL FILLER CAP
GOVERNOR ASSY.
WEIGHT, GOVERNOR
HOLDER, GOVERNORWEIGHT
PIN, GOVERNOR WEIGHT
SLIDER, GOVERNOR
CAP, OIL FILLER
WASHER, 6X16
CLIP, GOVERNOR HOLDER
OIL SEAL, 35X52X8
WASHER, PLAIN, 6 MM
PIN, DOWEL, 8X12
BOLT, FLANGE, 8X40
BEARING, RADIAL BALL 6202
BEARING, RADIAL BALL 6207
CAP, OIL FILLER
1
1
1
3
1
3
1
1
1
1
1
1
2
7
1
1
1
6
7#
8*+
9*+
10*+
11*+
12*+
13*+
14*+
15
16+
17*
18
90701HC4000
959000804000
961006202000
961006207000
15620735700
19+
20+
21#
GDP-5000H A.C. GENERATOR — OPERATION AND PARTS MANUAL — REV. #2 (07/23/08) — PAGE 57
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX340K1 ENGINE — FLYWHEEL/FAN ASSY.
FLYWHEEL/FANASSY.
PAGE 58 — GDP-5000H A.C. GENERATOR— OPERATION AND PARTS MANUAL — REV. #2 (07/23/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX340K1 ENGINE — FLYWHEEL/FAN ASSY.
FLYWHEEL/FANASSY.
NO
1
PART NO
PART NAME
QTY. REMARKS
19511ZE3000
28451ZE3W01
31100ZE3721
90201ZE3790
90741ZE2000
FAN, COOLING
PULLEY, STARTER
FLYWHEEL COMP.
NUT, SPECIAL, 16 MM
KEY, SPECIAL WOODRUFF
1
1
1
1
1
2
3
4
5
GDP-5000H A.C. GENERATOR — OPERATION AND PARTS MANUAL — REV. #2 (07/23/08) — PAGE 59
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX340K1 ENGINE — COIL ASSY.
COILASSY.
PAGE 60 — GDP-5000H A.C. GENERATOR— OPERATION AND PARTS MANUAL — REV. #2 (07/23/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX340K1 ENGINE — COIL ASSY.
COILASSY.
NO
1
PART NO
PART NAME
QTY. REMARKS
30500ZE2013
30700ZE1013
31510ZE1811
31511ZE3000
31512ZE2000
36101ZE3800
36103ZE1000
90012888000
90013883000
90015883000
COIL ASSY., IGNITION
CAP ASSY., NOISE SUPPRESSO
COIL ASSY., LAMP 12V/25W
CLAMP, WIRE
1
1
1
1
1
1
1
4
1
2
2
3
4
5
GROMMET, CORD
6
CORD, STOP SWITCH
HOLDER, STOP SWITCH CORD
BOLT, FLANGE, 6X40
BOLT, FLANGE, 6X12
BOLT, FLANGE, 6X28
7
8
9
10
GDP-5000H A.C. GENERATOR — OPERATION AND PARTS MANUAL — REV. #2 (07/23/08) — PAGE 61
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX340K1 ENGINE — CRANKSHAFT ASSY.
CRANKSHAFTASSY.
PAGE 62 — GDP-5000H A.C. GENERATOR— OPERATION AND PARTS MANUAL — REV. #2 (07/23/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX340K1 ENGINE — CRANKSHAFT ASSY.
CRANKSHAFTASSY.
NO
1
PART NO
PART NAME
QTY. REMARKS
13310ZE3701
13351ZE3010
13352ZE3310
14311ZE3310
961006207000
CRANKSHAFT COMP. ..................... 1 ....INCLUDES ITEMS W/
*
2
WEIGHT, BALANCER
GEAR, BALANCER DRIVE
GEAR, TIMING
1
1
1
1
3
*
*
4
*
5
BEARING, RADIAL BALL, 6207
GDP-5000H A.C. GENERATOR — OPERATION AND PARTS MANUAL — REV. #2 (07/23/08) — PAGE 63
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX340K1 ENGINE — ELECTRIC STARTER ASSY.
ELECTRIC STARTERASSY.
PAGE 64 — GDP-5000H A.C. GENERATOR— OPERATION AND PARTS MANUAL — REV. #2 (07/23/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX340K1 ENGINE — ELECTRIC STARTER ASSY.
ELECTRIC STARTERASSY.
NO
PART NO
PART NAME
QTY. REMARKS
1
31204ZA0003
31206ZE3003
31207ZE3013
31201ZE3013
31211ZE2003
31212ZE3003
31213ZE2003
31215ZE2003
31218ZE3003
31219ZE2003
31222ZE3791
31231ZE2003
31232ZE3003
31233ZE2003
90110ZE2003
91601ZE2003
938920501418
938920503218
9407206080
CONTACTOR ASSY,
ARMATURE COMP
1
*
2
1
*
3
CLUTCH COMP, OVER RUNNING . 1 ....INCLUDES ITEMS W/
#
*
*
4
MOTOR UNIT, STARTER ................ 1 ....INCLUDES ITEMS W/
5
BRAKET, CENTER
BRAKET, FR
1
1
1
2
1
4
1
1
1
1
1
1
1
4
2
2
*
6
*
7
GEAR, DRIVE DINION
BRUSH
*
8
*
9
YOKE COMP
*
10
SPRING, BRUSH RETURN
GEAR, REDUCTION
HOLDER, BRUSH
WIRE, WATER COVER
INSULATOR
*
11
12
13
14
15
16
17
18
19
#
*
*
*
*
*
*
*
*
*
SCREW-WASHER, 4X6
PACKING
SCREW-WASHER, 5X14
SCREW-WASHER, 5X32
NUT-WASHER, 6MM
BOLT, FLANGE, 8X35
20
957010803508
GDP-5000H A.C. GENERATOR — OPERATION AND PARTS MANUAL — REV. #2 (07/23/08) — PAGE 65
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX340K1 ENGINE — GOVERNOR CONTROLS ASSY.
GOVERNOR CONTROLSASSY.
PAGE 66 — GDP-5000H A.C. GENERATOR— OPERATION AND PARTS MANUAL — REV. #2 (07/23/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX340K1 ENGINE — GOVERNOR CONTROLS ASSY.
GOVERNOR CONTROLSASSY.
NO
1
PART NO
PART NAME
QTY. REMARKS
16550ZE3700
16555ZE3000
16561ZE3000
16562ZE3700
16570ZE3700
16584883300
90013883000
90015ZE5010
93500050350A
9405006000
ARM, GOVERNOR
ROD, GOVERNOR
SPRING, GOVERNOR
SPRING, THROTTLE RETURN
1
1
1
1
2
3
4
5
CONTROL ASSY. ............................. 1 ....INCLUDES ITEMS W/
*
6
SPRING, CONTROL ADJUSTING
BOLT, FLANGE, 6X12
1
1
1
1
1
*
7
8
9
BOLT, GOVERNOR ARM
SCREW, PAN, 5X35
NUT, FLANGE, 6MM
*
10
GDP-5000H A.C. GENERATOR — OPERATION AND PARTS MANUAL — REV. #2 (07/23/08) — PAGE 67
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX340K1 ENGINE — CARBURETOR ASSY.
CARBURETORASSY.
PAGE 68 — GDP-5000H A.C. GENERATOR— OPERATION AND PARTS MANUAL — REV. #2 (07/23/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX340K1 ENGINE — CARBURETOR ASSY.
CARBURETORASSY.
NO
PART NO
PART NAME
QTY. REMARKS
1
16010ZE3701
16011ZA0931
16013ZA0931
16015ZA0931
16016ZH7W01
16024124761
16028ZA0931
16100ZE3F10
16124ZE0005
16148141881
16166ZE3701
16211ZE3700
16221ZE3800
16223ZE3800
16230ZE3701
16260ZE2722
16261ZE2702
16262ZE2711
16263ZA0000
16264ZE2701
16265ZE2721
16268ZE2721
16269ZA0800
16400ZE2703
16611ZE2711
16613893000
16615893000
36135ZV1003
53149964003
90431ZE2700
90432ZE2700
90433ZE2700
90434ZE2700
90650SD9003
93500050120A
938920501208
9405006000
GASKET SET
1
1
1
1
1
1
1
*
2
VALVE SET, FLOAT
FLOAT SET
*
3
*
4
CHAMBER SET, FLOAT
SCREW SET
*
5
6
SCREW SET, DRAIN
SCREW SET
*
7
*
8
CARBURETOR ASSY. ..................... 1 ... INCLUDES ITEMS W/
*
9
SCREW, THROTTLE STOP
CAP, CHOKE DUST
1
1
1
1
1
1
1
*
10
*
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
NOZZLE, MAIN
INSULATOR, CARBURETOR
PACKING, CARBURETOR
PACKING, INSULATOR
VALVE ASSY., SOLENOID
*
STAY, MANUAL CHOKE ................... 1 .. INCLUDES ITEMS W/
#
#
#
#
#
#
#
STAY, COMP., SOLENIOD
LEVER, CHOKE
1
1
1
1
1
1
2
1
1
1
1
1
1
1
2
1
1
1
2
2
2
1
1
1
1
4
1
1
1
1
JOINT, ROD
ROD, CHOKE
STOPER, CHOKE ROD
SPRING, MANUAL CHOKE
PACKING, AIR CLEANER
DIAPHRAGM ASSY.
ROD, CHOKE CONTROL
GROMMET, CHOKE ROD
GUIDE, CHOKE ROD
VALVE, DASHPOT CHECK
BUSH, ARM PIVOT
WASHER, CHOKE LEVER
SEAL, CHOKE LEVER
WASHER, THRUST
COLLAR, LOVER
#
#
#
#
#
#
#
#
#
CLIP, WIRE HARNESS
SCREW, PAN, 5X12
SCREW, WASHER 5X12
NUT, FLANGE, 6MM
WASHER, PLAIN 5MM
E-RING 2MM
#
*
#
#
#
#
9410305000
9454002010
9454004010
E-RING 4MM
9454007010
E-RING 7MM
9500202070
CLIP B7, TUBE
950053507510
950053513010
99101ZF50920
99101ZF50950
TUBE, 3.5X75
TUBE, 3.5X130
JET, MAIN, #92
*
JET, MAIN, #95
GDP-5000H A.C. GENERATOR — OPERATION AND PARTS MANUAL — REV. #2 (07/23/08) — PAGE 69
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX340K1 ENGINE — SOLENOID ASSY.
SOLENOIDASSY.
PAGE 70 — GDP-5000H A.C. GENERATOR— OPERATION AND PARTS MANUAL — REV. #2 (07/23/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX340K1 ENGINE — SOLENOID ASSY.
SOLENOIDASSY.
NO
1
PART NO
PART NAME
QTY. REMARKS
16268893000
17850ZD1E30
36160ZB4003
93500050080A
90013883000
SPRING, CHOKE RETURN
LEVER COMP., THROTTLE
SOLENOID ASSY.
SCREW, PAN
BOLT, FLANGE, 6X2
1
1
1
2
1
2
3
4
5
GDP-5000H A.C. GENERATOR — OPERATION AND PARTS MANUAL — REV. #2 (07/23/08) — PAGE 71
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX340K1 ENGINE — FUEL COCK ASSY.
FUEL COCK ASSY.
PAGE 72 — GDP-5000H A.C. GENERATOR— OPERATION AND PARTS MANUAL — REV. #2 (07/23/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX340K1 ENGINE — FUEL COCK ASSY.
FUEL COCK ASSY.
NO
PART NO
PART NAME
PACKING, FUEL STRAINER CUP
QTY. REMARKS
1
COCK ASSY., FUEL ......................... 1 ..... INCLUDES ITEMS W/
1
16173001004
16950ZB4015
16952ZB4005
16958397771
16959471831
16967GA6671
90854ZB2000
950014521040
9500202080
*
2
*
3
SCREEN, FUEL STRAINER
O-RING
FILTER CUP
CUP, FUEL STRAINER
RUBBER, FUEL TUBE
TUBE, FUEL, 4.5X210
CLIP B8, TUBE
1
1
1
1
1
1
2
*
4
*
5
*
6
*
7
8
9
GDP-5000H A.C. GENERATOR — OPERATION AND PARTS MANUAL — REV. #2 (07/23/08) — PAGE 73
Download from Www.Somanuals.com. All Manuals Search And Download.
TERMS AND CONDITIONS OF SALE — PARTS
PAYMENT TERMS
5. Partsmustbeinnewandresalablecon- Multiquipreservestherighttoquoteandsell
dition,intheoriginalMultiquippackage(if directtoGovernmentagencies,andtoOriginal
any), and with Multiquip part numbers Equipment Manufacturer accounts who use
Terms of payment for parts are net 30 days.
FREIGHTPOLICY
clearlymarked.
our products as integral parts of their own
products.
All parts orders will be shipped collect or
prepaidwiththechargesaddedtotheinvoice.
All shipments are F.O.B. point of origin.
Multiquip’sresponsibilityceaseswhenasigned
manifesthasbeenobtainedfromthecarrier,
andanyclaimforshortageordamagemustbe
settledbetweentheconsigneeandthecarrier.
6. Thefollowingitemsarenotreturnable:
SPECIALEXPEDITINGSERVICE
a. Obsolete parts. (If an item is in the
price book and shows as being re- A$35.00surchargewillbeaddedtotheinvoice
placedbyanotheritem,itisobsolete.) forspecialhandlingincludingbusshipments,
insuredparcelpostorincaseswhereMultiquip
mustpersonallydeliverthepartstothecarrier.
(such as gaskets, seals, “O” rings,
b. Any parts with a limited shelf life
andotherrubberparts)thatwerepur- LIMITATIONSOFSELLER’SLIABILITY
MINIMUMORDER
chasedmorethansixmonthspriorto
thereturndate.
Multiquip shall not be liable hereunder for
damagesinexcessofthepurchasepriceofthe
TheminimumchargeforordersfromMultiquip
is $15.00 net. Customers will be asked for
instructionsregardinghandlingofordersnot
meetingthisrequirement.
c. Anylineitemwithanextendeddealer item with respect to which damages are
netpriceoflessthan$5.00.
claimed, and in no event shall Multiquip be
liable for loss of profit or good will or for any
otherspecial,consequentialorincidentaldam-
ages.
d. Special order items.
RETURNEDGOODSPOLICY
e. Electricalcomponents.
f. Paint,chemicals,andlubricants.
g. Decalsandpaperproducts.
h. Itemspurchasedinkits.
Returnshipmentswillbeacceptedandcredit
willbeallowed,subjecttothefollowingprovi-
sions:
LIMITATIONOFWARRANTIES
Nowarranties,expressorimplied,aremade
in connection with the sale of parts or trade
accessoriesnorastoanyenginenotmanufac-
tured by Multiquip. Such warranties made in
connectionwiththesaleofnew,completeunits
are made exclusively by a statement of war-
rantypackagedwithsuchunits,andMultiquip
neitherassumesnorauthorizesanypersonto
assume for it any other obligation or liability
whatever in connection with the sale of its
products.Apartfromsuchwrittenstatementof
warranty, there are no warranties, express,
impliedorstatutory,whichextendbeyondthe
descriptionoftheproductsonthefacehereof.
1. AReturnedMaterialAuthorizationmust
be approved by Multiquip prior to ship-
ment.
7. Thesenderwillbenotifiedofanymaterial
receivedthatisnotacceptable.
2. ToobtainaReturnMaterialAuthorization,
alistmustbeprovidedtoMultiquipParts
Salesthatdefinesitemnumbers,quanti-
ties, and descriptions of the items to be
returned.
8. Suchmaterialwillbeheldforfiveworking
days from notification, pending instruc-
tions.Ifareplyisnotreceivedwithinfive
days,thematerialwillbereturnedtothe
senderathisexpense.
a. Thepartsnumbersanddescriptions
must match the current parts price
list.
9. Creditonreturnedpartswillbeissuedat
dealer net price at time of the original
purchase,lessa15%restockingcharge.
b. The list must be typed or computer
generated.
10. In cases where an item is accepted, for
which the original purchase document
can not be determined, the price will be
basedonthelistpricethatwaseffective
twelvemonthspriortotheRMAdate.
c. The list must state the reason(s) for
thereturn.
Effective: February 22, 2006
d. The list must reference the sales
order(s)orinvoice(s)underwhichthe
itemswereoriginallypurchased.
11. Credit issued will be applied to future
purchasesonly.
e. The list must include the name and
phonenumberofthepersonrequest-
ingtheRMA.
PRICINGANDREBATES
Prices are subject to change without prior
notice.Pricechangesareeffectiveonaspe-
cificdateandallordersreceivedonorafterthat
datewillbebilledattherevisedprice.Rebates
3. AcopyoftheReturnMaterialAuthoriza-
tionmustaccompanythereturnshipment.
4. Freight is at the sender’s expense. All forpricedeclinesandaddedchargesforprice
partsmustbereturnedfreightprepaidto increaseswillnotbemadeforstockonhand
Multiquip’sdesignatedreceivingpoint.
atthetimeofanypricechange.
PAGE 74 — GDP-5000H A.C. GENERATOR— OPERATION AND PARTS MANUAL — REV. #2 (07/23/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
GDP-5000H A.C. GENERATOR — OPERATION AND PARTS MANUAL — REV. #2 (07/23/08) — PAGE 75
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION AND PARTS MANUAL
HERE’S HOW TO GET HELP
PLEASE HAVETHE MODEL AND SERIAL
NUMBER ON-HANDWHEN CALLING
UNITED STATES
Multiquip Corporate Office
18910 Wilmington Ave.
Carson, CA 90746
MQ Parts Department
800-427-1244
310-537-3700
Tel. (800) 421-1244
Fax (800) 537-3927
Fax:800-672-7877
Fax:310-637-3284
Contact: [email protected]
Mayco Parts
800-306-2926
310-537-3700
Warranty Department
800-421-1244, Ext. 279 Fax:310-537-1173
310-537-3700, Ext. 279
Fax:800-672-7877
Fax:310-637-3284
Service Department
800-421-1244
Technical Assistance
800-478-1244
Fax:310-537-4259
Fax:310-631-5032
310-537-3700
MEXICO
MQ Cipsa
UNITED KINGDOM
Multiquip (UK) Limited Head Office
Hanover Mill, Fitzroy Street,
Ashton-under-Lyne,
Carr. Fed. Mexico-Puebla KM 126.5
Momoxpan, Cholula, Puebla72760Mexico
Tel: (52) 222-225-9900
Fax: (52) 222-285-0420
Tel: 0161 339 2223
Fax: 0161 339 3226
Lancashire OL7 0TL
CANADA
Multiquip
4110IndustrielBoul.
Laval, Quebec, Canada H7L 6V3
Tel: (450) 625-2244
Fax: (450) 625-8664
© COPYRIGHT 2008, MULTIQUIP INC.
Multiquip Inc and the MQ logo are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without written permission. All other trademarks are
the property of their respective owners and used with permission.
This manual MUST accompany the equipment at all times. This manual is considered a permanent part of the equipment and should remain with the unit if resold.
The information and specifications included in this publication were in effect at the time of approval for printing. Illustrations, descriptions, references and technical data
contained in this manual are for guidance only and may not be considered as binding. Multiquip Inc. reserves the right to discontinue or change specifications, design or
the information published in this publication at any time without notice and without incurring any obligations.
Your Local Dealer is:
Download from Www.Somanuals.com. All Manuals Search And Download.
|