OPERATION AND PARTS MANUAL
SP3 “STREET PRO”
PROFESSIONAL SLAB SAW
35 HP WISCONSIN DIESEL ENGINE
MODELS
SP303516, SP303520, SP303526
SP303530
Revision #3 (09/29/06)
To find the latest revision of this
publication, visit our website at:
www.multiquip.com
THIS MANUAL MUST COMPANY THE EQUIPMENT AT ALL TIMES.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 CONCRETE SAW
PROPOSITION 65 WARNING
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 1
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 CONCRETE SAW
SILICOSIS /RESPIRATORY HAZARDS
WARNING WARNING
SILICOSIS WARNING
RESPIRATORY HAZARDS
Grinding/cutting/drilling of masonry, concrete, metal and
other materials with silica in their composition may give
off dust or mists containing crystalline silica. Silica is a
basic component of sand, quartz, brick clay, granite and
numerous other minerals and rocks. Repeated and/or
substantial inhalation of airborne crystalline silica can
cause serious or fatal respiratory diseases, including
silicosis. In addition, California and some other
authorities have listed respirable crystalline silica as a
substance known to cause cancer. When cutting such
materials, always follow the respiratory precautions
mentioned above.
Grinding/cutting/drilling of masonry, concrete, metal and
other materials can generate dust, mists and fumes
containing chemicals known to cause serious or fatal
injury or illness, such as respiratory disease, cancer,
birth defects or other reproductive harm. If you are
unfamiliar with the risks associated with the particular
process and/or material being cut or the composition of
the tool being used, review the material safety data
sheet and/or consult your employer, the material
manufacturer/supplier, governmental agencies such as
OSHA and NIOSH and other sources on hazardous
materials. California and some other authorities, for
instance, have published lists of substances known to
cause cancer, reproductive toxicity, or other harmful
effects.
Control dust, mist and fumes at the source where
possible. In this regard use good work practices and
follow the recommendations of the manufacturers or
suppliers, OSHA/NIOSH, and occupational and trade
associations. Water should be used for dust
suppression when wet cutting is feasible. When the
hazards from inhalation of dust, mists and fumes cannot
be eliminated, the operator and any bystanders should
always wear a respirator approved by NIOSH/MSHA for
the materials being used.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 2
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 CONCRETE SAW
Table of Contents
PROPOSITION 65 WARNING .......................................................................................1
SILICOSIS /RESPIRATORY HAZARDS......................................................................2
PARTS ORDERING PROCEDURES........................................................................... 6
SAFETY..............................................................................................................................7
HAZARD SYMBOLS.................................................................................................... 8
GENERAL SAFETY WARNINGS ....................................................................................... 11
BLADE SAFETY ......................................................................................................... 13
SAW TRANSPORTATION SAFETY......................................................................... 14
EMERGENCIES .......................................................................................................... 14
MACHINE OPERATION AND SAFETY DECALS................................................... 15
SERIAL TAG ................................................................................................................... 16
OPERATION ...................................................................................................................17
BEFORE STARTING......................................................................................................... 17
CONTROL PANEL ........................................................................................................... 18
ENGINE POWER, CUTTING POWER & SHEAVE SIZE........................................................ 19
INSTALLING THE BLADE, BLADE GUARD & BLADE FLANGE ......................................... 20
REMOVING THE BLADE, BLADE GUARD & BLADE FLANGE........................................... 21
STACKING BLADES FOR WIDE CUTS .............................................................................. 22
INSTALLING AND REMOVING THE BLADE GUARD.......................................................... 23
WATER SUPPLY AND CONTROL ..................................................................................... 26
HANDLEBARS................................................................................................................. 27
FUELING THE SAW ......................................................................................................... 28
STARTING AND STOPPING THE ENGINE .......................................................................... 29
POINTER ADJUSTMENT .................................................................................................. 30
RAISE – LOWER CONTROLS ........................................................................................... 31
SETTING THE DEPTH GAUGE & DEPTH STOP ................................................................. 32
DRIVE SYSTEM .............................................................................................................. 33
NIGHT LIGHT ................................................................................................................. 36
TRANSPORTATION TIE-DOWNS AND LIFT POINT ............................................................ 37
OPERATION ON A SLOPE OR INCLINE.............................................................................. 38
FREEING A STUCK BLADE .............................................................................................. 38
DRAINING THE WATER SYSTEM..................................................................................... 39
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 3
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 CONCRETE SAW
MAINTENANCE.............................................................................................................40
REMOVABLE GUARDS AND ACCESS PANELS.................................................................. 40
BELTS AND PULLEYS ..................................................................................................... 41
BLADE FLANGE REMOVAL/INSTALLATION .................................................................... 45
CIRCUIT BREAKERS ....................................................................................................... 50
MAXIMUM CUT DEPTH ADJUSTMENT............................................................................ 50
LUBRICATION ................................................................................................................ 51
ENGINE MAINTENANCE ................................................................................................. 52
RAISE-LOWER SYSTEM.................................................................................................. 53
CONTROL HANDLE ADJUSTMENT .................................................................................. 54
HYDRAULIC SYSTEM ..................................................................................................... 55
POSITRACTION ADJUSTMENT......................................................................................... 60
EXPLANATION OF CODE IN REMARKS COLUMN.............................................61
SUGGESTED SPARE PARTS.......................................................................................62
COMPONENT DRAWINGS..........................................................................................63
NAMEPLATE AND DECALS ASSY.................................................................................... 63
DECK/GAUGE PANEL ASSY. .......................................................................................... 65
CONSOLE/SHEET METAL ASSY...................................................................................... 67
ACCESS PANEL ASSY..................................................................................................... 69
FUEL TANK ASSY. ......................................................................................................... 71
F-N-R CONTROL HANDLE ASSY.................................................................................... 73
JOYSTICK MOUNTING ASSY........................................................................................... 75
LIFT PUMP CIRCUIT ASSY.............................................................................................. 77
WATER SYSTEM ASSY. .................................................................................................. 79
DEPTH INDICATOR ASSY................................................................................................ 81
HANDLE AND LIGHT ASSY............................................................................................. 83
FRONT/REAR POINTER ASSY. ........................................................................................ 85
GAUGES AND CONTROLS ASSY...................................................................................... 87
FRONT AXLE ASSY. ....................................................................................................... 89
DEPTH STOP ASSY. ........................................................................................................ 91
PLATFORM ASSY............................................................................................................ 93
DRIVE ASSY................................................................................................................... 95
BLADESHAFT AND MOUNTING ASSY. ............................................................................ 97
POSITRACTION ASSY...................................................................................................... 99
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 4
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 CONCRETE SAW
PULLEY AND V-BELT ASSY. ........................................................................................ 101
BATTERY ASSY............................................................................................................ 103
ENGINE BRACKETS ASSY............................................................................................. 105
ENGINE INSTALLATION ASSY....................................................................................... 107
BLADEGUARD ASSY..................................................................................................... 109
OPTIONAL WATER PUMP KIT ASSY. ............................................................................ 111
COLLAR PULLER ASSY................................................................................................. 113
SEAL SLEEVE PULLER/SEAL INSTALLATION TOOL ...................................................... 115
BUSHING EXTENSION KITS .......................................................................................... 117
ELECTRIC SCHEMATIC...........................................................................................119
SPECIFICATIONS........................................................................................................120
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 5
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 CONCRETE SAW
PARTS ORDERING PROCEDURES
Ordering parts has never been easier!
Choose from three easy options:
If you have an MQ Account, to obtain a
Username and Password, E-mail us at:
Order via Internet (Dealers Only):
Order parts on-line using Multiquip’s SmartEquip website!
View Parts Diagrams
Best Deal!
To obtain an MQ Account, contact your
District Sales Manager for more information.
Order Parts
Print Specification Information
Fax your order in and qualify for a 5% Discount
on Standard orders for all orders which include
complete part numbers.*
Go to www. Multiquip .com and click on
to log on and save!
Order Parts
Note: Discounts Are Subject To Change
Fax your order in and qualify for a 3% Discount
on Standard orders for all orders which include
complete part numbers.*
Order via Fax (Dealers Only):
All customers are welcome to order parts
via Fax.
Domestic (US) Customers dial:
1-800-6-PARTS-7 (800-672-7877)
Note: Discounts Are Subject To Change
Domestic (US) Dealers Call:
1-800-427-124
Order via Phone:
Non-Dealer Customers:
International Customers should contact their local
Multiquip Representatives for Parts Ordering I
information.
Contact your local Multiquip Dealer
for parts or call 800-427-1244 for help
in locating a dealer near you.
When ordering parts, please supply:
.
Dealer Account Number
.
Specify Preferred Method of Shipment:
.
.
.
.
.
Dealer Name and Address
.
.
.
.
Fed Ex/UP
Priority On
Ground
Next Day
Second/Third Day
DHL
Shipping Address (if different than billing address)
Return Fax Number
Applicable Model Number
Truck
Quantity, Part Number and Description of each Part
Unless otherwise indicated by customer, all orders are treated as Standard Orders and will ship
within 24 hours. We will make every effort to ship Air Shipments the same day the order is received,
if received prior to 2PM PST. Stock Orders must be noted on fax or web order form.
NOTE
WE ACCEPT ALL MAJOR CREDIT CARDS!
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 6
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 CONCRETE SAW
SAFETY
FOR YOUR SAFETY AND THE SAFETY OF OTHERS!
This Owner's Manual has been developed to provide instructions for the
safe and efficient operation of the Multiquip SP-3035 CONCRETE SAW.
For engine maintenance information, please refer to the engine
NOTE
manufacturers’ instructions for data relative to its safe operation.
Before using this CONCRETE SAW, ensure that the operating individual
has read and understands all instructions in this manual.
Safety precautions should be followed at all times when operating this equipment. Failure to read and
understand the Safety Messages and Operating Instructions could result in injury to yourself and others.
SAFETY MESSAGE ALERT SYMBOLS
The three (3) Safety Messages shown below will inform you about potential hazards that could
injure you or others. The Safety Messages specifically address the level of exposure to the
operator, and are preceded by one of three words: DANGER, WARNING, or CAUTION.
DANGER: You WILL be KILLED or SERIOUSLY injured if you
DO NOT follow directions.
DANGER
WARNING: You CAN be KILLED or SERIOUSLY injured if you
DO NOT follow directions.
WARNING
CAUTION: You CAN be injured if you DO NOT follow directions.
CAUTION
Potential hazards associated with SP-3035 Concrete Saw operation will be referenced with "Hazard
Symbols" which appear throughout this manual, and will be referenced in conjunction with Safety
"Message Alert Symbols".
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 7
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 CONCRETE SAW
HAZARD SYMBOLS
Engine exhaust gases contain poisonous carbon monoxide. This
gas is colorless and odorless, and can cause death if inhaled.
NEVER operate this equipment in a confined area or enclosed
structure that does not provide ample free flow of air.
Lethal Exhaust
Gases
Gasoline is extremely flammable, and its vapors can cause an
explosion if ignited. DO NOT start the engine near spilled fuel or
combustible fluids. DO NOT fill the fuel tank while the engine is
running or hot. DO NOT overfill the tank, since spilled fuel could
ignite if it comes into contact with hot engine parts or sparks from
the ignition system. Store fuel in approved containers, in well-
ventilated areas and away from sparks and flames. NEVER use
fuel as a cleaning agent.
Explosive Fuel
Engine components can generate extreme heat. To prevent
burns, DO NOT touch these areas while the engine is running or
immediately after operations. NEVER operate the engine with heat
shields or heat guards removed.
Burn Hazards
NEVER operate equipment with covers, or guards removed. Keep
fingers, hands, hair and clothing away from all moving parts to
prevent injury.
Rotating Parts
ALWAYS place ON/OFF switch to the OFF position, remove key
and/or disconnect the spark plug leads before servicing the
engine, equipment, or supporting components. Ground the lead to
prevent sparks that could ignite a fire.
Accidental
Starting
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 8
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 CONCRETE SAW
HAZARD SYMBOLS
NEVER tamper with factory settings of engine governor or speed
settings. Ensure the proper Speed Kits are installed to safely
support the prescribed RPM settings for diamond blade
operations.
Over Speed
NEVER operate the saw without blade guards and covers in
place. Adhere to safety guidelines ANSI American National
Standards Institute, OSHA, and/or other applicable local
regulations.
Guards and
Covers in Place
Rotating Blade can cut, tear, and crush. Keep hands and feet
clear.
Rotating Blade
ALWAYS wear approved respiratory protection.
Respiratory
Hazard
ALWAYS wear approved eye and hearing protection.
CRUSH AND PINCH HAZARD Keep hands and feet clear.
Sight &
Hearing Hazard
Crush Hazard
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 9
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 CONCRETE SAW
HAZARD SYMBOLS
NEVER use your hand to find hydraulic leaks. Use a piece of wood
or cardboard. Hydraulic fluid injected into the skin must be treated
by a knowledgeable physician immediately or severe injury or death
can occur.
Skin Injection
Hazard
Text set off like this presents clarifying information, specific
instructions or commentary designed to help prevent damage to
your saw, other property, or the environment.
NOTE
Other important messages are provided throughout this manual to
help prevent damage to your concrete saw, other property, or the surrounding
environment.
Equipment Damage Message
Other important messages are provided throughout this manual
to help prevent damage to your concrete saw, other property, or
the surrounding environment.
CAUTION
This concrete saw, other property, or the surrounding environment could be
damaged if you do not follow instructions.
NOTE
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 10
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 CONCRETE SAW
General Safety Warnings
Most accidents involving product operation, maintenance and repair are caused by failure to
observe basic safety rules and precautions. Accidents can often be avoided by recognizing
potentially hazardous situations before an incident occurs.
Before operating the saw, make sure all protective guards are securely
in place. All saws are supplied with a blade guard, collar guard and belt
guard.
Whenever necessary, replace operation and safety decals if they
become difficult to read
Verify the engine start switch is set to the OFF position before installing
a blade.
Make sure the operator knows how to turn the engine OFF in case of
an emergency.
Do not go near rotating parts (blades, belts, pulleys or wheels) while
engine is running.
Muffler and exhaust gases are extremely hot. Stay clear of muffler and
exhaust gases. Allow these parts to cool before servicing the saw.
Stay clear of the saw while it is being hoisted.
Anytime the saw is lifted onto its nose, or tilted fully back, for
maintenance access, the high end MUST be blocked up to prevent the
possibility of crush injury!
WARNING
Allow the engine to cool before adding fuel or performing service and
maintenance functions. Contact with HOT components can cause
serious burns.
Never operate the saw in any enclosed or narrow area where free flow
of air is restricted. If the airflow is restricted it will cause serious
damage to the saw’s engine and may cause injury to people.
Remember the saw’s engine gives off DEADLY carbon monoxide gas.
ALWAYS refuel in a well-ventilated area; away from sparks and open
flame. Avoid “topping off” the filler port as spills can result.
ALWAYS use extreme caution when working with flammable liquids.
When refueling, STOP the engine and allow it to cool.
NEVER smoke around or near the machine. Fire or explosion could
result from fuel vapors, or if fuel is spilled on a HOT engine.
NEVER operate the saw in an explosive atmosphere where fumes are
present or near combustible materials. An explosion or fire could
result causing severe bodily harm or even death.
NEVER use fuel as a cleaning agent.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 11
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 CONCRETE SAW
General Safety Warnings
ALWAYS read, understand, and follow procedures in the Operator’s
Manual before attempting to operate the equipment.
Be sure the operator is familiar with proper safety precautions and
operating techniques before using the saw.
Make sure the operating area is clear before starting the engine.
Maintain this equipment in a safe operating condition at all times
Keep the saw clean. It will work better and last longer
Use proper blades and follow the blade manufacturer’s
recommendations. Match blade rpm (Spindle rpm) to recommended
blade surface feet per minute (SFPM).
WARNING
Tighten the 5/8” blade-mounting bolt to 100-125 foot-lbs. torque.
Turn engine OFF prior to fueling the saw!
Start engine with the joystick in NEUTRAL to prevent unexpected saw
movement.
Do not leave saw unattended while engine is running.
Do not start engine on a sloping surface to prevent unexpected loss of
control.
Do not park or leave saw unattended on a slope - the saw can roll when
the engine is OFF. Block the unit when leaving.
If the saw must be parked on a slope, turn it across the angle of the
slope, to prevent accidental downhill movement.
Prior Always store equipment properly when not being used. Equipment
should be stored in a clean, dry location out of the reach of children.
When storing the saw in freezing weather, blow out water lines to
prevent damage to components in the water delivery system.
Prior to service, level the frame surface.
Do not over tighten the Spindle drive belt
Turn on water flow prior to starting the engine, to prevent damage to the
impeller of a belt-driven water pump.
Don’t pollute! Waste oils and other chemicals must be disposed of in a
manner consistent with local and state environmental protection
regulations.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 12
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 CONCRETE SAW
BLADE SAFETY
. ALWAYS inspect diamond blades before each use.
The blade should exhibit no cracks, dings, or flaws in
the steel centered core and/or rim. Center (arbor)
hole must be undamaged and true.
. Examine blade flanges for damage, excessive wear
and cleanliness before mounting blade. Blade should
fit snugly on the shaft and against the inside/outside
of the saw.
. Only cut the material that is specified by the blade.
Read the specifications of the blade to ensure the
proper tool has been matched to the material being
cut.
WARNING
. ALWAYS keep blade guards in place. Exposure of
the blade must not exceed 180 degrees.
. Ensure that the blade does not come into contact
with the ground or surface during transportation. DO
NOT drop the blade on the ground or surface.
. The engine governor is designed to permit maximum
engine speed in a no-load condition. Speeds that
exceed this limit may cause the blade to exceed the
maximum safe allowable speed.
. Ensure that the blade is mounted for proper
operating direction.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 13
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 CONCRETE SAW
SAW TRANSPORTATION SAFETY
.
.
Use appropriate lifting equipment to ensure the safe
movement of the saw.
DO NOT use the handle bars and/or front pointer as lifting
points.
WARNING
.
.
NEVER attempt to tow the untrailered saw behind a vehicle.
NEVER transport the saw with the blade mounted.
EMERGENCIES
.
ALWAYS know the location of the
nearest fire extinguisher.
.
.
ALWAYS know the location of the
nearest first aid kit.
In emergencies always know the
location of the nearest phone or
keep a phone on the job site.
WARNING
Know the phone numbers of the
nearest ambulance, doctor, and fire
department. Knowing this information
is invaluable in the case of an emergency
and could keep a serious situation from
becoming a tragic one.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 14
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 CONCRETE SAW
MACHINE OPERATION AND SAFETY DECALS
The Multiquip SP-3035 Saw is equipped with a number of operation and safety decals. Should
any of these decals become unreadable, replacements can be obtained from your dealer.
WARNING
To avoid injury,
you MUST read
and understand
operator’s manual
before using this
P/N 21571
machine.
This machine to
1-1/2” x 2-1/4”
be operated by
qualified
personnel only.
Ask for training
as needed.
WARNING
Nasfsaer dfghhte thsfaw wiot
P/N 35137
Nesfaer dfgat
the sfarbs in
saccty guizcin
cbccR) 19b4
P/N 20525
P/N 35137
Nasfsaer dfghhte thsfaw wiot
Nesfaer df
the sfarbs i
n pbb
P/N 604000
Nasfsaer dfghhte thsfaw wiot
Nesfaer dfg
the sfarbs i
WARNING
WARNING!
Nesfaer dfgate ths
the sfarbs i
Neer dfgate ths
the sfarbs in pbb
KEEP HANDS
CLEAR
KEEP FEET
CLEAR
Nesfar dfgate ths
tfarbs in pbb
P/N 25249-001
P/N 25250-001
P/N 604001
SMI
Nasfsaer dfghhte thsfaw wiot
P/N 22122-001
CAUTION
When Larger Blade and Guard
is Installed, Belt Drive MUST
Be Changed to Proper Size.
See Owners Manual.
FAILURE TO COMPLY WITH THE C C AH
JADV EEE AV EEA OIEJGGVCBVVZ
A
T
P/N 36099 (ISO Blue)
T
I
O
A
T
O
T
I
O
N
O
R
N
R
S.M.I. MASONRY AND CONCRETE
SAW MANUFACTURER’S INSTITUTE
P/N 23330-001
P/N 25491
P/N 25678
D
E
W
R
O
P
P/N 25483
(small)
C
O
D
E
A
T
P/N 13118
P/N 606004
P/N 25782
MODEL
SERIAL NO.
HOT
BELT DRIVE
CHECK
LUBRICATION
DECAL SHEET INTL STDS
P/N 11246
CONTACT MULTIQUIP
SERVICE DEPARTMENT
Fig. 1 — Decals
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 15
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 CONCRETE SAW
Serial Tag
Fig. 2 — Serial Tag
For future reference, fill in the model number and serial number of
your saw in the space above.
NOTE
The serial tag contains the model number and serial number of the saw. This information details
all parts that were included with the saw when it was shipped from the factory, as well as the date
of manufacture.
Record your ENGINE model number, spec. number and serial number here:
MODEL NO.
SPEC. NO.
SERIAL NO.
The serial tag is bonded to the inside panel of the console.
Serial Tag
Engine
Serial
Numbers
Fig. 3 — Serial Number Locations
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 16
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 CONCRETE SAW
OPERATION
Before Starting
Walk around the saw and ensure that all guards
and panels are properly installed.
Wear eye and hearing protection.
Wear protective clothing.
1. Check engine and hydraulic oil.
2. Verify the proper-sized blade guard is fully installed on the blade guard mounting tab.
3. Adjust handlebars for best operator control.
4. If a belt driven water pump is installed, turn on the water flow before starting the engine.
Console
Access Panel
Handlebars
Belt Guard
Rear Access
Panel
Flange
Blade Guard
Fig. 4 — Guards & Panels
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 17
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 CONCRETE SAW
Control Panel
Auxiliary
Switch
Engine
Tach
Light Switch
Disengage
Voltmeter
Throttle
Engine On-
Off-Start
Choke
Depth
Gauge
Fuel
Tank
Cap
Plunge
Button
Depth
Zero
Gauge
Positraction
Control
Maintenance
Information
Operating
Instructions
Speed Control
Joystick
Safety
Warnings
Water
Pump
Switch
Water
Flow
Control
Fig. 5 — The Control Panel
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 18
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 CONCRETE SAW
Engine Power, Cutting Power & Sheave Size
NEVER tamper with factory settings of engine governor
or speed settings. Ensure the proper Speed Kits are
installed to safely support the prescribed RPM settings
for diamond blade operations.
WARNING
Blade Size & Configuration per Model
The SP-3035 is available in four Blade Speed configurations. The following chart shows the
various configurations for each model.
Blade Model
Size
Engine
RPM No
Load
Spindle
RPM No
Load
Governor Ratio Engine Engine
Spindle
Spindle Surface
Setting
(Hole
Kit
Pulley
Part
Pulley Pulley Part
Pulley
Size
Feet Per
Minute
Size
Number
Number)
Number
16"
20"
26"
30"
Q303516
Q303520
Q303526
Q303530
3000
2520
2000
1773
3000
2800
2800
2600
12
9
25603
25849
35103
35104
540000
540070
540012
540012
3.8"
3.6"
3.0"
3.0"
540006
540066
540065
540049
3.8"
4.0"
4.2"
4.4"
12566
13195
13614
13923
7
5
When choosing a blade for your cutting conditions, follow the blade manufacturer’s
recommendations. Match blade RPM (Spindle RPM) to the recommended blade Surface Feet Per
Minute (SFPM).
SFPM 12” dia.
RPM
14”
dia.
16” dia. 18” dia.
20”
dia.
24” dia.
RPM
26”
dia.
30”
dia.
RPM
RPM
RPM
2183
2319
2456
2592
2728
2865
3001
3138
3274
3410
3548
RPM
1528
1623
1719
1814
1910
2005
2101
2196
2292
2387
2483
RPM
1175
1249
1322
1396
1469
1543
1616
1690
1763
1836
1910
RPM
1019
1082
1146
1210
1273
1337
1401
1464
1528
1592
1655
8,000
8,500
2546
2706
2865
3024
3183
3342
3501
3661
3820
3979
4138
1910
2029
2149
2268
2387
2507
2626
2745
2865
2984
3104
1698
1804
1910
2016
2122
2228
2334
2440
2546
2653
2759
1273
1353
1432
1512
1592
1671
1751
1830
1910
1989
2069
9,000
9,500
10,000
10,500
11,000
11,500
12,000
12,500
13,000
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 19
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 CONCRETE SAW
Installing the Blade, Blade Guard & Blade Flange
Remain Clear of all parts of saw while installing blade to
prevent crush injury or death.
Verify the engine start switch is OFF before installing
blade.
WARNING
Tighten the 5/8” blade-mounting bolt to 100-125 foot-
pounds torque.
The blade can be mounted on either side of the saw to accommodate different cutting jobs.
1. Raise the saw so that the blade will clear the ground when installed.
2. Verify that blade flanges are clean and undamaged.
3. Insert the bushing and mounting bolt through the outer flange and blade.
4. Align flange pin through the blade into the inner flange.
5. Tighten the 5/8” mounting bolt to 100-125 foot-pounds of torque.
The blade mounting bolt on the right side of the saw (as viewed from the
operator’s position) has a left hand-thread, while the blade-mounting bolt on
the left side of the saw has a right-hand thread.
NOTE
Outer Flange
with Pin
Blade Guard
Mounting Clip
Flange
Bushing
Inner Flange
Tapered
Spindle Shaft
Mounting
Bolt
Fig. 6 — Blade Components
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 20
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 CONCRETE SAW
Removing the Blade, Blade Guard & Blade Flange
Remain Clear of all parts of saw while installing blade to
prevent crush injury or death.
Verify the engine start switch is OFF before installing
blade.
WARNING
Tighten the 5/8” blade-mounting bolt to 100-125 foot-
pounds torque.
1. Raise the saw so that the blade will clear the ground.
2. Remove blade guard. See fig. 7
3. Remove the mounting bolt from the outer flange and bushing.
4. Remove blade, outer flange and bushing simultaneously.
5. Reinstall the flange bushing, outer flange and mounting bolt.
6. Tighten the 5/8” mounting bolt to 75 foot-pounds of torque.
The blade mounting bolt on the right side of the saw (as viewed from the
operator’s position) has a left hand-thread, while the blade-mounting bolt on
the left side of the saw has a right-hand thread.
NOTE
Blade Guard
Figure 7. Blade Guard Removal
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 21
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 CONCRETE SAW
Stacking Blades for Wide Cuts
Remain Clear of all parts of saw while installing blade to
prevent crush injury or death.
Verify the engine start switch is OFF before installing
blade.
WARNING
Tighten the 5/8” blade-mounting bolt to 100-125 foot-
pounds torque.
Combining (stacking) blades to make wide cuts requires an optional Bushing Extension Kit.
Kit #18502 allows blade stacking from .375” to .75” thickness.
Kit #18501 allows blade stacking from .75” to 1.125” thickness.
1. Ensure on/off switch is off. See Fig. 5 or Fig. 15
2. Remove the existing blade. See Removing the Blade Fig. 7
3. Replace the standard Flange Bushing, Flange Pin, and Mounting Bolt that came with the saw
with the longer Bolt, Pin and Bushing which comes with the Kit.
4. Insert the Bushing and Mounting Bolt through the Outer Flange and Blades. The longer
bushing and bolt allow blades to be stacked together.
5. Align the Flange Pin through the stack of Blades into the Inner Flange.
6. Tighten the 5/8” Mounting Bolt to 100-125 foot-pounds of torque.
7. Install blade guard.
Inner Collar
Outer Collar
With Pin
Tapered
Blade Shaft
Mounting
Bolt
Collar
Bushing
Fig. 8 — Blade Stacking
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 22
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 CONCRETE SAW
Installing and Removing the Blade Guard
Blade Guards for the SP-3035 concrete saw can be installed on either side of the saw.
Verify the engine start switch is OFF before installing
blade.
WARNING
Remain clear of all parts of saw while installing blade to
prevent crush injury or death.
Installing the Blade Guard
1. Ensure on/off key is off. See Fig. 5 or Fig. 15
2. Slide the Blade Guard Mounting Clip onto the Guard Mounting Tab on the frame.
3. Connect the water delivery hose to the Blade Guard.
4. Ensure that the water tubes are pointed toward the water distribution grooves in the Blade
Collars. See Fig. 10
5. Make sure the front-hinged section of the Blade Guard is fully closed before use.
Top Handle
Water Delivery Hose
Rear Handle
Blade Guard
hinged front
Blade Guard
Mounting Clip
Blade Guard
rear section
Fig. 9 — The Blade Guard installed
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 23
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 CONCRETE SAW
Removing the Blade Guard
During use, the Blade Guard can become tight on the tapered mounting tab. To loosen it, wiggle
the Rear Blade Guard Handle up and down, while lifting with the Top Handle.
Blade Guard Water Supply
Verify that the water hose on the saw is connected to the Blade Guard and that the water pipes are
pointed into both Blade Collars.
Make sure that the outlets of the water tubes point toward the lower
portion of the blade collars, aimed at the delivery ports, for proper
water delivery to the blade.
NOTE
Water Tube bracket
Water Tube aimed at
groove in Blade Collar
Blade Collar
Fig. 10 — Water Tubes and the Blade Collar
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 24
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 CONCRETE SAW
Installing the Flange Guard
The Flange Guard provides protection from the Blade Flange not in use.
1. Verify that the unused Blade Flange is secured to the Spindle by tightening the mounting bolt.
2. Slide the Flange Guard onto the Guard Mounting Tab on the frame.
Flange Guard
Flange
Fig. 11 — The Flange Guard, Installed
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 25
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 CONCRETE SAW
Water Supply and Control
To prevent damage to the impeller of a belt driven water pump, do
not run the engine with the water pump switch on, unless the water
supply is connected and water is flowing.
When storing the saw during freezing weather, blow out the water
lines to prevent damage to the water delivery system.
WARNING
Connect the job water hose to the water inlet fitting on the left side of the saw.
Verify that the water hose on the saw is connected to the Blade Guard and that the water delivery
tubes are pointed into both lower Blade Flanges.
The yellow lever on the control panel regulates water flow volume.
If the saw is equipped with an optional water pump, the ON/OFF switch is on the control panel
next to the water flow control valve.
Because of the water delivery efficiency of the 24-port blade flanges,
these saws use less water for blade cooling and flushing than other
saws.
NOTE
Flow Control
Water Inlet
Lever
Optional
Water Pump
Hose to
Blade Guard
Pump
ON/OFF
Switch
Fig. 12 — The Water Supply System
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 26
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 CONCRETE SAW
Handlebars
The handlebars are adjustable to three different angles, for optimum operator control, and can
also be slid fully inward for storage. Once handlebars are adjusted, lock them into position by
tightening the lock knob on each side.
Using the handlebars in position #2 or #3, when employing larger diameter blades reduces the
need to bend over and the effort required by the operator to maneuver the unit.
Lock Knob
P 3
P 2
P 1
Three
operating
positions
Storage
position
Fig. 13 — Handlebar Positions
Using the handlebars in position #2 or #3 when employing larger
diameter blades, reduces the need to bend over, and reduces the effort
required by the operator to maneuver the saw.
NOTE
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 27
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 CONCRETE SAW
Fueling the Saw
The 3000 Series saws feature a five-gallon clear molded plastic fuel tank with a sight gauge,
central drain, and shutoff valve. The gas tank cap is located at the front of the saw.
To prevent damage to the impeller of a belt driven water pump, do not
run the engine with the water pump switch on, unless the water
supply is connected and water is flowing.
When storing the saw during freezing weather, blow out the water
WARNING
lines to prevent damage to the water delivery system.
Use 90+ Octane Unleaded Gasoline Only
CAUTION
Gas Tank Cap
Fuel Tank
Fuel Sight
Gauge slots
Inline Fuel
Filter
Fuel Shut-off
Valve
Fig. 14 — Fueling the Saw
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 28
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 CONCRETE SAW
Starting and Stopping the Engine
Do not leave the saw unattended while the engine is running.
Do not start, park, or leave the saw unattended on a slope.
WARNING
CAUTION
If the saw has an optional water pump, do not run the saw dry
with the water pump switch ON — otherwise the pump impellers
will be damaged.
In normal operation, do not stop the engine abruptly when hot!
Reduce the throttle to idle and allow the engine to run one or two
minutes before turning the ignition switch off.
1. Check Oil levels in engine and hydraulic system
2. If water pump option is installed, start water supply to blade.
3. Move the speed control joystick to NEUTRAL position.
4. Set the throttle to ½ open
5. Turn on/off switch to “START” position and at the same time pull out choke cable only
sufficient to start the engine. Release choke cable after engine starts. Re-choke if engine tends
to stall. When engine starts, release switch to “RUN” position. Allow engine to warm up
before applying load.
6. Ensure that water lines are attached and water is flowing to the saw.
7. Set the throttle to the recommended engine RPM to match the recommended blade speed of
the attached blade.
8. Lower the blade to the cut depth.
9. Move the joystick FORWARD to advance the cut.
10. When finished cutting, allow the engine to cool down by running at 1000 to 1200 RPM for 3
to 5 minutes depending on how hot the engine has been. This will reduce the chance of
engine damage or vapor lock.
Make sure the operator knows how to turn the engine off in case of an
emergency.
Do not go near rotating parts (blade, belts, pulleys, or wheels) while
WARNING
the saw is running.
To stop the engine, turn the “ON-OFF” switch to the “OFF” position.
ON/OFF
Switch
Fig. 15 — ON/OFF Switch Location
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 29
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 CONCRETE SAW
Pointer Adjustment
1. Lower the front pointer assembly: Release the rope from the cam cleat, and rotate the pointer
forward into position.
2. Adjust the pointer rod by loosening the lock knob: Once the pointer rod is set to the cut line,
tighten the lock knob.
3. Adjust the rear pointer to the cut line: Loosen the lock bolt, position the pointer rod, and
tighten the lock bolt.
4. To raise the front pointer assembly, pull back and up on the pointer cable.
5. Secure the pointer assembly in the desired raised position by locking the cable between the
jaws of the cam cleat.
Pointer
Rod
Pointer
Cable
Pointer Rod
Lock Knob
Fig. 16 — Pointer Adjustment
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 30
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 CONCRETE SAW
Raise – Lower Controls
This saw uses a 12-volt hydraulic pump and cylinder to raise and lower the blade. Controls are
located on the speed control joystick handle.
Plunge Button
Raise Button
Fig. 17 — Joystick Handle
1. To plunge the blade, depress the button on the outer end of the handle.
2. To raise the blade, depress the button on the forward side of the handle.
See the Maintenance section of this manual for a diagram of the Raise-Lower System components.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 31
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 CONCRETE SAW
Setting the Depth Gauge & Depth Stop
The 3000 Series saws use a cable-controlled Depth Gauge and mechanical Depth Stop to lock the
blade at the desired cut depth. See Fig. 18.
Setting the Depth Gauge
1. Lower the blade until it just touches the cutting surface.
2. Turn the Depth Gauge dial to zero.
The Depth Gauge will show the depth of cut. It should not be necessary to readjust the Depth
Indicator until a different diameter of blade is installed.
Setting the Depth Stop
1. Lower the blade into the cut until the desired cutting depth is achieved.
2. Turn the Depth Stop Crank clockwise to take slack out of the Depth Stop.
To increase cutting depth, turn the Depth Stop Crank counter-clockwise. To reduce cutting depth,
turn the Depth Stop Crank clockwise.
Depth
Stop
Crank
Depth
Gauge
Fig. 18 — Setting the Depth Gauge and Depth Stop
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 32
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 CONCRETE SAW
Drive System
The 3000 Series saws have a cable-controlled Hydro-Gear hydrostatic powered transaxle with
fully adjustable F-N-R (Forward-Neutral-Reverse) speed adjustment via a joystick control handle.
The system utilizes a remote oil filter. There are no chains, sprockets or gearboxes requiring daily
service.
The 3000 Series saws can travel at speeds up to 250 feet per minute.
Transaxle Oil
Filter
Positraction
Engagement
Lever
Transaxle
Positraction Bar
Fig. 19 — The Drive System
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 33
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 CONCRETE SAW
Drive System Controls
The control handle controls FORWARD-NEUTRAL-REVERSE (F-N-R) speeds and the raising and
lowering of the saw. To increase forward speed, slowly move the joystick FORWARD. Pulling the
joystick backward decreases saw speed, and when the joystick passes NEUTRAL the saw moves
into REVERSE. Reverse speed is also controlled by the position of the joystick.
Although not a true “free wheeling” mode, the Drive Disengage handle, when pulled, allows the
saw to be freely moved when the engine is not running.
DO NOT DISENGAGE WHILE ENGINE IS RUNNING.
Drive
Disengage
Positraction
Lever
Speed Control
Joystick in
NEUTRAL position
Fig. 20 — Drive System Controls
Start the engine with the Forward-Neutral-Reverse Control in
NEUTRAL to prevent unexpected saw movement.
WARNING
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 34
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 CONCRETE SAW
Positraction
Positraction, when ON, locks both drive wheels together for straight-line movement. It is
recommended for all cutting and is especially helpful on uneven surfaces, and when loading and
unloading the saw.
1. Move the Positraction lever to “ON” (positraction engaged) to lock both drive wheels.
2. To unlock the drive wheels for easy maneuverability and turning, move the Positraction lever
to OFF.
See the Maintenance Section for instructions on aligning the wheels
to correct pulling to the right or left.
NOTE
Positraction
Engagement
Lever
Positraction Bar
Fig. 21 — The Positraction System
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 35
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 CONCRETE SAW
Transaxle
The hydrostatic-powered transaxle has no chains, sprockets or gearboxes to service. There is a
simple cable control for forward-reverse motion, and a single drive belt from the engine to power
the transaxle.
Fig. 22 —Transaxle
Night Light
The optional night light can be used on either side of the saw, and can be extended and rotated for
best illumination of the cutting area. Once the light is aimed, lock it in position by tightening the
lock knob. The light can be removed for storage by loosening the lock knob, disconnecting the
light cord plug and sliding the light bar out of the saw.
Night
Light
Fig. 23 — Night Light
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 36
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 CONCRETE SAW
Transportation Tie-downs and Lift Point
Tie-downs
The saw is provided with holes at each corner of the lower frame for easy tie-down during
transportation. The saw MUST be tied down whenever it is being transported.
Tie-down
Tie-down
Fig. 24 —Tie-down Points
Lift Point
The convenient single point for raising the saw with a hoist is located on top of the engine.
Lift Point
Fig. 25 — Lift Point
To avoid possible injury, stay clear of the saw while it is
being hoisted.
WARNING
To avoid possible damage to the saw, use approved rigging
when hoisting the saw.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 37
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 CONCRETE SAW
Operation on a Slope or Incline
Never operate, cut, or face the saw down a slope or incline. The weight of the saw will shift to the
front wheels allowing the rear wheels to skid or come completely off the ground. This allows the saw
to free wheel and possibly cause a runaway condition.
Always remove the blade when transporting or moving the saw outside of the cutting area. Use
the following procedures for loading and unloading the saw.
Using Inclined Ramps to Load and Unload the Saw
Loading UP a Ramp
1. Make sure ramps are of sufficient strength and width to adequately support and load saw.
Ensure the slope of the ramp is gentle enough to load the saw.
2. Remove blade from Spindle if installed.
3. Ensure saw is warmed up to decrease the chance of the engine stalling.
4. Run the engine between ¾ and full throttle.
5. Raise front of saw only enough to get started up ramp. As the rear wheels approach the ramp,
start lowering the front end of the saw. Raise and lower the front end as necessary to keep the
blade flanges off trailer deck.
6. Turn engine off, lower saw fully.
7. Tie the saw down securely for transit.
Unloading DOWN a Ramp
Unload the saw by backing it down the ramp. Never use a ramp with too great a slope as to create
an unsafe loading condition. Use the techniques stated in the steps above to clear the ramp while
keeping the front of the saw as close to the ramp as possible while backing it down. Never unload
with the saw front facing downward on a ramp.
Freeing a Stuck Blade
The only acceptable method for freeing a stuck blade is to remove the saw from the stuck or
pinched blade. DO NOT try to get the blade unstuck using the Raise/Lower system or by lifting
the saw by the lifting bale, etc.
Ensure ignition switch is turned off
Remove blade guard
Remove blade mounting bolt and outer flange
Maneuver saw away from blade
Make a parallel cut next to blade to free blade.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 38
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 CONCRETE SAW
If an attempt is made to start the saw with the blade pinched, the starter will suffer damage. If an
attempt is made to use the lift pump to raise the saw to free the blade, the lift motor and front axle
could be damaged. If an attempt is made to lift the saw and blade out of the cut utilizing
equipment such as a loader or back hoe, the saw frame and axle are likely to be damaged.
If the Water System is not drained when the saw is not in use and
temperatures fall below 32˚F, damage may occur to optional water
CAUTION
pumps and/or oil coolers.
Draining the Water System
When low temperatures fall below 32˚F:
1. If the saw is equipped with an optional Water Pump, open the drain petcock on the pump and
allow the pump to drain.
2. With the engine running, turn the water pump switch on for a few seconds to purge water
remaining inside the pump body.
3. Tilt the saw up and back, to allow water to drain.
4. Tilt the saw forward, to allow water to drain again.
If an air compressor is available, blow out the system by applying compressed air to the Water
Inlet
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 39
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 CONCRETE SAW
MAINTENANCE
This saw has many service-saving features, such as fully enclosed oil bath lubricated Spindle
bearings, which require no daily lubrication.
Level the saw frame surface prior to service in order to get accurate
oil level readings.
NOTE
Removable Guards and Access Panels
For ease of service access, the following guards and panels are removable:
Blade guard
Rear access panel
Belt guard
Flange Guard
Console Access Panel
Replace guards and panels prior to starting the engine.
Console Access Panel
Upper
Belt
Rear Access Panel
Guard
Lower
Belt
Protector
Blade Guard
Fig. 26 — Guards and Panels
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 40
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 CONCRETE SAW
Belts and Pulleys
Belt
Qty
1
Part Number
520006
Spindle Drive Belt (POWERBAND)
Transaxle Drive Belt
1
521005
Engine to Jack shaft Drive Belt
1
521005
Spindle
(Blade Shaft)
Drive Belt
TransAxle Drive Belt
Engine
to
Jack Shaft
Drive Belt
Fig. 27 — Belt Locations
V-Belt Tension
The ideal V-Belt tension is the lowest tension at which the belt will not slip under peak load
conditions. Check V-Belt tension frequently during the first 24-48 hours of run-in operation.
.
Over-tensioning shortens belt and bearing life.
. Keep belts clean of foreign material that may cause slippage.
. Make V-Belt inspection a periodic procedure.
. Never dress belts, as this causes premature failure.
CAUTION
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 41
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 CONCRETE SAW
Spindle (Blade Shaft) Drive Belt Tension Adjustment
When loosening drive belts, lower the saw to reduce stress on the
tensioning system, and use gravity to pull the engine forward slightly.
When tightening belts, raise the saw, and gravity will aid the process
also.
NOTE
NEVER attempt to check or adjust the V-belt
tension with the engine running. Severe injury can
WARNING
occur. Keep fingers, hands, hair, and clothing
away from all moving parts.
1. Remove the Upper Belt Guard (see Fig. 26).
2. Loosen the front Engine Mount lock bolts (A, A) only, to allow the engine to slide. DO NOT
loosen the rear bolts (B, B).
3. With the front bolts loose, the rear Engine Mount bolts (B, B) should have a ¼” space, as
shown:
B
A
¼”
Space
A
B
Fig. 28 — Detail of Engine Mount Lock Bolts
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 42
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 CONCRETE SAW
4. Loosen the Outer Jam Nut on the Single Point Belt Tension Bolt. Turn the Inner Jam Nut
counter-clockwise.
5. Adjust drive belt to desired tension. Do Not over tighten.
6. Tighten Engine Mount Lock Bolts.
7. Tighten the Jam Nuts to prevent the Single-Point Bolt from turning.
Engine Mount
Inner Jam Nut
Lock Bolt (1 of 2)
Outer Jam Nut
Spindle Belt
Upper Belt Guard Bolt
Lower Belt Guard Bolts
Single-Point
Belt Tension Bolt
Lower Belt Guard
Fig. 29 — Spindle Drive Belt Adjustment & Replacement
Replacing the Spindle Drive Belt
1. Remove the Upper and Lower Belt Guards. See Figs. 26 & 29.
2. Loosen the Engine Mount Lock Bolts.
3. Loosen the Single-Point Belt-Tensioning Bolt to allow the belt to slip off the engine
sheave.
4. Slide the belt off of the engine sheave and pull the belt down around the Spindle
sheave.
5. Slide the belt off the top of the Spindle sheave.
6. Reverse steps 1-5 to install a new belt.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 43
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 CONCRETE SAW
Replacing the Jack Shaft Belt
NEVER attempt to check or adjust the V-belt
tension with the engine running. Severe injury can
occur. Keep fingers, hands, hair, and clothing
away from all moving parts.
WARNING
1. Remove the Belt Guards (see Figs. 26 & 29).
2. Loosen the Rotary Tensioner.
3. Remove the Spindle Belt (see above).
4. Remove and replace the Jack Shaft Belt.
5. Replace the Spindle Belt (see above).
6. Adjust the Rotary Tensioner.
Rotary Belt Tensioner
The Rotary Belt Tensioner system uses a 3/4”-headed bolt and either a 15/16” or 1” nut to set belt
tension. Adjust Tension Nut to apply tension to the belt. Ridges on the Tensioner Arm gauge the
amount of tension applied.
1. Loosen the Tensioner Lock Bolt Head.
2. Adjust the Tensioner Nut for proper belt tension. (This will be achieved at
approximately 1-1/2 ridges on the gauge.)
3. Tighten the Tensioner Lock Bolt Head.
Jack Shaft Pulley
The Tensioner Nut is
on opposite side
Tensioner Lock Bolt
Head
Tensioner Base
Tensioner Pulley
Fig. 30 — Jack Shaft Belt and Rotary Belt Tensioner System
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 44
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 CONCRETE SAW
Blade Flange Removal/Installation
Correct removal or installation of the Inner Blade Flange or Flange requires a Flange Puller
(option Part Number 18503) as shown below.
Follow instructions closely to prevent injury from flying Blade Flanges!
Because of tapered fit between Blade Flange and Spindle, 5-10 tons
of force is needed to release the inner flange. Parts and tools can
become dangerous projectiles if instructions are not followed properly.
WARNING
Front Puller Plate
Perimeter Bolt
Puller Bolt
Horseshoe Plate
Perimeter Bolt
Perimeter Bolt
Fig. 31 — Using the Flange Puller
Removing the Inner Blade Flange
With the Outer Blade Flange in place, and the Blade Mounting Bolt loosened approximately ¼”:
1. With the three perimeter bolts holding the two Puller Plates together, slide the Horseshoe Plate
of the Flange Puller behind the (Shaft) side of the Inner Flange as shown above.
2. Tighten the center Puller bolt to remove the Inner Flange from Spindle.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 45
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 CONCRETE SAW
Ensure the Outer Flange is in place to prevent the
Puller and Inner Flange from flying off when the taper
breaks loose, and causing injury!
DANGER
If the Inner Flange does not readily come free from the tapered
Spindle, lightly tap on the central Puller bolt. This should cause
the flange to break free from the shaft.
NOTE
Installing the Inner Blade Flange
1. Ensure that the tapered portion of the Spindle, and the Inner Spindle are perfectly clean and
free of burrs or indentations. Clean and repair as necessary.
2. Ensure that the Drive Key is in place.
3. Slide the Inner Flange onto the tapered portion of the Spindle.
Do Not use any lubricant!
Lubricant prevents the tapered
surfaces of the Flange and Shaft from mating properly.
NOTE
4. Install the Outer Blade Flange, Flange Bushing, and Mounting Bolt.
5. Tighten with a ½” impact wrench to seat the tapered surfaces of the Inner Flange and Spindle.
Flange Bushing
Outer Flange
Dowel pin
Inner
Drive Key
Spindle
Fig. 32 — Installing the Inner Spindle
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 46
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 CONCRETE SAW
6. Loosen the Mounting Bolt and remove the Outer Flange and Bushing.
7. Inspect the Inner Flange to ensure the proper seating of the tapered fit.
The Inner Flange should be seated between .030” and 0.0” (flush) to the end of the Spindle.
Fig. 33 — Proper seating of the Inner Flange and Spindle
8. Test to ensure that the Inner Flange does not wobble when rotated. Use a dial indicator on the
face of the Flange. Maximum tolerance is .003” run-out on the face of the Flange.
For Spindle Maintenance/hydraulic oil change see page 58.
NOTE
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 47
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 CONCRETE SAW
Spindle Replacement
To assure correct Spindle/Wheel alignment it is recommended that
this operation be performed by a Multiquip Authorized Service Center.
DO NOT unbolt the Spindle Mounting Blocks, as they have been
factory installed for correct Spindle/wheel alignment.
NOTE
1. Remove the Spindle Drive Belts (see Replacing the Spindle Belt, above).
2. Tighten the Engine Mount Lock Bolts to prevent engine movement during step #3.
Engine Mount
Lock Bolt
Engine Mount
Lock Bolt
Fig. 34 — Engine Mount Lock Bolts
To prevent the possibility of crush injury, always
ensure that the saw is securely supported whenever it
is lifted for maintenance.
DANGER
3. Block the wheels then lift the saw to the full up position, and block up the front axle to prevent
accidental crush injury.
4. Disconnect the two hoses attached to the Spindle, and plug hoses and Spindle ports to prevent
drips and dirt contamination.
5. Support the Spindle to prevent tipping or shifting of weight.
6. Unbolt the Spindle Saddle Clamps using a 3/8” Allen wrench.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 48
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 CONCRETE SAW
Spindle Mounting
Block
DO NOT REMOVE
Spindle Mounting
Block
DO NOT REMOVE
Saddle
Clamps
Lower Belt
Protector
Fig. 35 — Spindle Replacement
7. Remove the Spindle.
DO NOT unbolt the Spindle Mounting Blocks, as they have been factory-installed
for correct Spindle/wheel alignment.
8. Fill the new Spindle with approved hydraulic oil and cap.
9. Perform Steps 1-5 in reverse order.
Spacing
Spacing
Fig. 36 — Maintain equal spacing when tightening Saddle Clamps
Tighten Saddle Clamp bolts equally, maintaining even spacing as you reattach the
Saddle Clamps. Torque bolts to 35 ft. lbs. Do Not over-torque. Apply medium
strength thread lock, Blue Loctite 242 or equivalent.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 49
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 CONCRETE SAW
Circuit Breakers
Three thermal circuit breakers are located behind the Control Panel access cover.
Remove Dash Panel to
access circuit breakers
Fig. 37 — Circuit Breaker location
Under normal circumstance circuit breakers do not require service; they are automatically re-set
once an overload condition has been corrected. If one or more breakers are cycling on/off, locate
the cause of the electrical overload and repair as required.
Also see the Electrical Schematic on page 61.
Maximum Cut Depth Adjustment
The 3000 Series saws come factory-adjusted for maximum usable cut depth. However, should
you desire to adjust the maximum depth:
1. Park the blade-less saw on a flat and level surface.
2. Fully lower the saw onto the Stop Bolts (see Fig. 38).
3. Measure the distance from the Blade Flanges to the surface.
4. Adjust the Stop Bolts in or out until the Blade Flanges have 1/8” to 3/16” ground clearance.
5. Ensure that both bolts are adjusted to the same setting so that the load is evenly distributed.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 50
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 CONCRETE SAW
Lubrication
This saw has six grease fittings. Locations are shown in Figure 38 on the front axle assembly, and
one, (not shown) on the Jackshaft assembly.
Front axle pivot bearings (2)
Hydraulic lift cylinder end (1)
Depth cylinder pivot bracket (2)
Jackshaft pivot (1)
These fittings are easily accessed by raising the saw half way up, and then lifting the rear of the
saw until the blade flanges rest on the ground.
To prevent the possibility of crush injury, ensure that
the saw is securely placed on suitable supports before
servicing the lubrication points.
WARNING
Grease each fitting every 25 hours of operation using premium grade
waterproof E. P. (extreme pressure) grease.
DANGER
F3
F2
F4
F5
F1
Maximum Cut
Depth Stop Bolt
Maximum Cut
Depth Stop Bolts
Fig. 38 — Grease Fittings and Maximum Cut Depth Stops
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 51
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 CONCRETE SAW
Engine Maintenance
The Model SP-3035 uses a 35 HP Wisconsin engine. See the engine manual for service details.
Check air filters daily. Do not clean. Replace as needed. See Caution below.
Check engine oil level daily.
Level the saw frame prior to service to get accurate readings.
Change the engine oil and filter every 50 hours of operation.
Filters
Filter
Qty
1
Part Number & Cross Reference
Primary Air Filter
Safety Air Filter
Engine Oil Filter
Hydraulic System Filter
Inline Fuel Filter
300000-1
300000-2
306004
1
1
1
306006
1
304000
Safety Air Filters are NOT intended to be used for primary air
filtration. When the Primary Filter becomes clogged, replace it
immediately – DO NOT run saw using just the Safety filter.
DO NOT attempt to clean dirty air filters by any means.
DANGER
Air filter
Engine
Oil filter
Hydraulic Oil
Reservoir
Fuel filter
Transaxle
filter
Fig. 39 — Filters
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 52
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 CONCRETE SAW
Raise-Lower System
This saw uses a 12-volt hydraulic pump and cylinder to power the raise-lower system.
Level the frame prior to service to get accurate readings.
Check oil level daily.
Fill the reservoir half full when cold.
Use 5W-30 premium grade engine oil.
Raise-Lower
Pump
Raise-Lower
Reservoir
Hydraulic
Manifold
Raise-Lower
Cylinder
Fig. 40 — Raise-Lower System
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 53
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 CONCRETE SAW
Control Handle Adjustment
The Control Handle is adjustable to provide the preferred “feel”.
1. Using a ¼” Allen wrench and 9/16” wrench, loosen both pivot bolts until they can be turned
by hand. Pivot #1 requires only a 9/16” wrench, as the Allen nut side is welded in place.
2. Tighten pivot #1 until the handle is close to the desired “feel”.
3. Tighten pivot #2 until it just starts to increase the force required to move the handle.
Pivot #1
Pivot #2
Fig. 41 — Control Handle Adjustment
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 54
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 CONCRETE SAW
Hydraulic System
The hydraulic system consists of:
Spindle Assembly (1)
Transaxle Assembly (9)
Lift Cylinder (5)
Hydraulic Pump (2)
Hydraulic Manifold (4)
Oil Filters (3, 6)
Hydraulic Drive and Spindle Oil Reservoir (7)
Lift Cylinder Reservoir (8)
Routine Maintenance
Check oil level daily.
Fill the reservoir to the fill line when cold.
Level frame prior to service to get an accurate reading.
Use 5W-30 premium grade engine oil.
Change transaxle oil and filter every 250 hours of operation or annually.
Change Spindle oil every 250 hours of operation or annually.
2
8
7
3
4
6
1
9
5
Fig. 42 — Hydraulic System Components
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 55
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 CONCRETE SAW
Draining & Filling the Hydraulic System
To drain the Transaxle
1. Remove the drain plug from the bottom of the Spindle housing and the bottom of the
Transaxle.
Drain Plug
Fig. 43 — Transaxle Drain Plug
Collect and dispose of the used oil and oil filter in an environmentally
friendly manner. Do not drain onto the ground or pour used oil down
drains.
NOTE
2.
3.
4.
5.
Remove the old oil filter. See Fig. 43, above.
Once drained, reinstall the drain plugs.
Pre-fill and install a new oil filter.
Refill the Transaxle with hydraulic oil as outlined on page 58
Pre-fill the oil filter with oil prior to installing to prevent hydraulic
pump damage.
CAUTION
To drain the Spindle
The fully enclosed Spindle eliminates most maintenance. However, if
the Spindle ever needs service or repair, contact Multiquip, at the
number listed in the inside of the front cover for details.
NOTE
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 56
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 CONCRETE SAW
To Remote Fill
Reservoir
Drain
Fig. 44 — Spindle Assembly
1. Raise the saw 2/3 or more up.
2. Remove the drain plug from the bottom of the Spindle housing.
3. Re-install the drain plug and install a new oil filter.
To prevent damage to the hydraulic pump, pre-fill the new oil filter
prior to installation.
CAUTION
To refill the hydraulic system
1. Ensure the saw is fully lowered if it had been raised.
2. Add hydraulic oil to the Drive & Spindle System Reservoir.
Oil will need to be added several times.
3. Jack the unit up so the drive wheels are off the ground, then run the engine for a couple
minutes to cycle oil throughout the system.
4. Add more oil as required.
5. Inspect for leaks after service.
Tips
Remove the oil reservoir cap to speed draining.
Before installing a new filter, fill the reservoir and let it drain down to the filter manifold.
Once new oil reaches the manifold, install the new pre-filled filter.
To help speed up the refilling process, raise the saw half-way up and lift the rear of the saw
until the Blade Flanges touch the ground.
After filling the system, jack the saw up so the drive wheels are off the ground. Start the
saw, and move the joystick half way into FORWARD, to purge air out of the system.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 57
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 CONCRETE SAW
Drive Wheel Alignment
Below is the suggested technique for aligning the wheels. Distance X is the same on either side;
the Front Axle and Spindle must be at right angles to the frame edge. Distance A is 3/16” (.187”)
longer on the right side, so that the saw steers slightly left. Users may wish to alter the alignment
to fit a particular application.
Fig. 45 — Drive Wheel Alignment
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 58
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 CONCRETE SAW
The drive wheels are aligned by adjusting the entire rear drive assembly.
1. Raise the saw halfway, then lift the rear of the saw until flanges touch the ground. Use suitable
supports to prevent tipping or shifting of weight.
2. Loosen the adjustment-side attachment bolts until washers spin freely.
3. Loosen pivot-side bolts enough to move the adjustment-side wheel in the appropriate
direction to achieve the desired alignment distance.
4. Tighten the Transaxle Attachment Bolts when the appropriate alignment distance is set.
Pivot Side
|
Adjustment Side
Pivot Side
Attachment Bolts
Adjustment Side
Attachment Bolts
Fig. 46 — Drive Wheel Alignment Bolt Locations
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 59
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 CONCRETE SAW
Positraction Adjustment
Clamp Position
(Inner Lip of Drive Hub)
Clamp Position
(Inside Wheel Lip)
Clamp Plate Bolt
Clamp Plate Bolt
Spacer Position
Fig. 47 — Positraction Adjustment Bolt Locations
1. Lift Saw 4” to 6” and tilt forward to place spindle flanges on ground. When flanges are on the
ground, depress Raise Button to raise the rear of the saw to full height. Use suitable stands to
hold rear of saw up.
2. Disengage Positraction Lever fully.
3. Loosen Positraction clamping plate bolts enough to adjust Positraction assembly.
4. Insert 1/8” flat spacer between Positraction drive hub and rear wheel on both sides. Use a
finger-type clamp to compress the drive hub and the rear wheel, insert spacers between
contact points of wheel and hub. Tighten clamp until rear wheel compresses slightly.
5. Tighten Positraction clamping bolts to secure Positraction assembly. Remove clamps and
spacer.
6. Remove supports. Grasp the handlebars securely and depress the “Lower” button until the
rear of the saw has lowered sufficiently to safely lower the rear wheels to the ground.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 60
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 CONCRETE SAW
EXPLANATION OF CODE IN
REMARKS COLUMN
A blank entry generally indicates that the item is not
sold separately or is not sold by Multiquip. Other
entries will be clarified in the “Remarks” Column.
The following section explains the different symbols
and remarks used in the Parts section of this manual.
Use the help numbers found on the back page of the
manual if there are any questions.
QTY. Column
Numbers Used - Item quantity can be indicated by a
number, a blank entry, or A/R.
A/R (As Required) is generally used for hoses or other
parts that are sold in bulk and cut to length.
The contents and part numbers listed in the
parts section are subject to change without
notice. Multiquip does not guarantee the
availibility of the parts listed.
A blank entry generally indicates that the item is not
sold separately. Other entries will be clarified in the
“Remarks” Column.
REMARKS Column
Sample Parts List:
Some of the most common notes found in the
“Remarks” Column are listed below. Other additional
notes needed to describe the item can also be shown.
NO. PART NO. PART NAME
QTY. REMARKS
1
12345
BOLT....................... 1..... INCLUDES ITEMS W/#
WASHER, 1/4 IN...... ...... NOTSOLDSEPARATELY
2#
Assembly/Kit - All items on the parts list with the
same unique symbol will be included when this item is
purchased.
2# 12347
WASHER, 3/8 IN...... 1.... MQ-45TONLY
3
4
12348
12349
HOSE.................... A/R... MAKE LOCALLY
BEARING................. 1.... S/N2345BANDABOVE
Indicated by:
“INCLUDES ITEMS W/(unique symbol)”
NO. Column
Serial Number Break - Used to list an effective serial
number range where a particular part is used.
Unique Symbols - All items with same unique symbol
($, #, +, %, or >) in the number column belong to the
same assembly or kit, which is indicated by a note in
the “Remarks” column.
Indicated by:
“S/N XXXXX AND BELOW”
“S/N XXXX AND ABOVE”
“S/N XXXX TO S/N XXX”
Duplicate Item Numbers- Duplicate numbers indicate
multiple part numbers are in effect for the same
general item, such as different size saw blade guards
in use or a part that has been updated on newer
versions of the same machine.
Specific Model Number Use - Indicates that the part
is used only with the specific model number or model
number variant listed. It can also be used to show a
part is NOT used on a specific model or model number
variant.
When ordering a part that has more
than one item number listed, check
Indicated by:
“XXXXX ONLY”
“NOT USED ON XXXX”
the remarks column for help in
NOTE
determining the proper part to order
“Make/Obtain Locally” - Indicates that the part can
be purchased at any hardware shop or made out of
available items. Examples include battery cables,
shims, and certain washers and nuts.
PART NO. Column
Numbers Used - Part numbers can be indicated by a
number, a blank entry, or TBD.
“Not Sold Separately” - Indicates that an item cannot
be purchased as a separate item and is either part of
an assembly/kit that can be purchased, or is not
available for sale through Multiquip.
TBD (To Be Determined) is generally used to show a
part that has not been assigned a formal part number
at time of publication.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 61
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 CONCRETE SAW
SUGGESTED SPARE PARTS
MQ SP-3035 CONCRETE SAW WITH WISCONSIN 35
HP AIR-COOLED DIESEL ENGINE
1 to 3 Units
Description
1..........300000-1...........FILTER, AIR, ELEMENT, PRIMARY
1..........300000-2...........FILTER, AIR ELEMENT, SAFETLY
1..........306004..............FILTER, OIL, WISCONSIN 35 HP
1..........306006..............FILTER, TRANSAXLE
1..........304000..............FILTER, FUEL, WISCONSIN 35 HP
1..........520006..............V-BELT, 6 3VX425 (GOODYEAR)
1..........521005..............V-BELT, AX-31 (GOODYEAR)
1..........15503................COMFORT GRIP KNOB
1..........H9406 ...............NIGHT LIGHT BULB
Qty.
P/N
Part numbers on this
Suggested Spare Parts List
may supercede/replace the
P/N's shown in the test
pages of this manual.
NOTE
1..........400000..............LIFT PUMP SOLENOID
1..........362002..............TUBE, WATER, RH SIDE
1..........362003..............TUBE, WATER, LH SIDE
1..........200019..............FLAP, MUD, BLADEGUARD
1..........406000..............SWITCH, ROCKER
2..........180000..............BLADE COLLAR, INSIDE
............180001..............BLADE COLLAR ASSY, OUTER
2..........980705..............PIN, DOWEL 3/8 X 1-1/4"
2..........582012..............BUSHING, QUICK DISCONNECT
SPINDLE
1..........915315..............SCREW, HHC 5/8-11 X 3 GRD8
1..........915316..............SCREW, HHC 5/8 -11 X 3 LH GR8
1..........25832................ROPE ASSY, FRONT POINTER
1..........35131................MOUNTING HORN, AXLE
1..........25839................FRONT WHEEL ASSY
2..........500011..............REAR WHEEL
2..........528038..............REAR WHEEL KEYLESS BUSHING
1..........29509................CAP, FUEL TANK 2.25 DIA, ONE WAY VALVE
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 62
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 Concrete Saw — Nameplate and Decals
COMPONENT DRAWINGS
Nameplate and Decals Assy.
The Multiquip SP-3035 Saw is equipped with a number of operation and safety decals. Should any of these decals
become unreadable, replacements can be obtained from your dealer.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 63
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 Concrete Saw — Nameplate and Decals
Nameplate and Decals Assy.
NO
1
2
3
4
PART NO
25250-001
606004
25782
21302
25785
PART NAME
QTY.
2
2
4
2
REMARKS
DECAL, WARNING, KEEP FEET CLEAR
DECAL, BLADE GUARD REMOVAL
DECAL, MQ DIAMOND LOGO
DECAL, WARNING, INSTALL BLADE GUARD
DECAL, SP3 LOGO
5
3
6
7
8
13118
35137
1997
DECAL, POWDER COATED
DECAL, WARNING, READ MANUAL
DECAL, NAMEPLATE
1
1
1
9
M600021
22122-001
25249-001
23330-001
25491
20525
604001
25678
DECAL, UNLEADED FUEL ONLY
DECAL, WARNING, SERIOUS INJURY
DECAL, WARNING, KEEP HANDS CLEAR
DECAL, CAUTION, DRIVE BELT
DECAL, ROTATION, CW
DECAL, WARNING, PROPOSITION 65
DECAL, WARNING, INSTALL BELT GUARD
DECAL, ROTATION, CCW
1
1
2
1
1
1
1
1
10
11
12
13
14
15
16
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 64
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 Concrete Saw — Deck/Gauge Panel Assy.
Deck/Gauge Panel Assy.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 65
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 Concrete Saw — Deck/Gauge Panel Assy.
Deck/Gauge Panel Assy.
NO
1
2
PART NO
M600020
M600019
PART NAME
GAUGE PANEL
DECK PANEL
QTY.
1
1
REMARKS
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 66
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 Concrete Saw — Console/Sheet Metal Assy.
Console/Sheet Metal Assy.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 67
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 Concrete Saw — Console/Sheet Metal Assy.
Console/Sheet Metal Assy.
NO
1#
2#
3#
8
18
19
22
25
26
28#
29#
30
31
32
PART NO
0166
933242
204007
25796
0655
25865
25805
3214
933244
15503
584011
923114
35180
13287
PART NAME
QTY.
REMARK
SCREW, HHC 3/8-16 X 7/8
WASHER, FLAT SAE 3/8 GRD 9 YZ
BELT GUARD
3
3
1
1
6
1
1
6
6
1
1
2
CONSOLE, RED
SCREW, HHC 5/16-18 X 3/4
HARNESS, LIGHT KIT, SOCKET
PANEL, CONSOLE COVER, RED
SCREW, HHC 1/2-13 X 1-1/4
WASHER, FLAT SAE 1/2 GRD 9 YZ
KNOB, COMFORT GRIP STAR, 3/8-16 X 1
WRENCH, 15/16" BLADE CLOSED END
SCREW, SHC 8-32 X 1/2
BELT GUARD ASSY...................................................... 1.................. INCLUDES ITEMS W/#
NUT, NYLOC 8-32
2
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 68
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 Concrete Saw — Access Panel Assy.
Access Panel Assy.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 69
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 Concrete Saw — Access Panel Assy.
Access Panel Assy.
NO
1#
2#
3#
4#
5#
6#
7#
8
PART NO
25795
29057
560020
577002
12287
10024
10930
25794
PART NAME
QTY.
1
1
2
1.75 FT.
4
4
4
REMARK
PANEL, REAR CONSOLE, RED
DOCUMENT BOX, CP90007-07
LATCH, REAR SAW ACCESS PANEL
WEATHER STRIP, REAR SAW ACCESS PANEL
SCREW, THP 1/4-20 X 3/4" SS
NUT, NYLOCK 1/4-20
WASHER, FENDER, 1/4 X 1-1/4"
PANEL ASSY., REAR CONSOLE, RED ........................ 1.................. INCLUDES ITEMS W/#
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 70
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 Concrete Saw — Fuel Tank Assy.
Fuel Tank Assy.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 71
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 Concrete Saw — Fuel Tank Assy.
Fuel Tank Assy.
NO
1#
2#
3#
4#
5#
6#
7#
8#
9#
10#
11#
12#
13
PART NO
1400003
29509
19633
446005
19473
35022
35059
2295
304000
35060
370626
367216
25831
25801
933242
4196
PART NAME
TANK, FUEL
QTY.
REMARK
1
1
1
1
4
1
1
1
1
1
1
1
CAP, FUEL TANK 2.25" DIA. ONE WAY VALVE
BUSHING, RUBBER FUEL DAPCO 10672
VALVE, FUEL ON/OFF 1/4"
CLAMP, HOSE WORM #2
CLAMP, LOOP CUSHIONED #8
HOSE, FUEL .250 ID, 12"
SCREW, HHC 1/4-20 X 7/8"
FILTER, FUEL, WISCONSIN
HOSE, FUEL .250 ID, 11"
FITTING, 45O 4BARB-1/8" MP
FITTING, 90O-1/8" FP-1/8" MP
FUEL TANK ASSY ..........................................................1................. INCLUDES ITEMS W/#
14
15
16
MOUNT, FUEL TANK
WASHER, FLAT SAE 3/8" GD9
SCREW, SHC 8-32 X 1/2"
1
4
4
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 72
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 Concrete Saw — F-N-R Control Handle Assy.
F-N-R Control Handle Assy.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 73
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 Concrete Saw — F-N-R Control Handle Assy.
F-N-R Control Handle Assy.
NO
1
2#
3#
4#
5#
6#
7#
8#
9#
10#
11
PART NO
560030
560028-6
5600028-8
560028-4
560028-3
560028-5
560028-1
60118
PART NAME
F-N-R CONTROL HANDLE ASSY. ......................1.......................INCLUDES ITEMS W/#
QTY.
REMARK
SCREW, #6-32 X 3/8
WASHER, FLAT #4 NYLON
RUBBER BOOT
PLATE, SIDE SWITCH
SWITCH ASSEMBLY
HANDLE HOUSING
WIRE, F-N-R
5
5
2
1
2
1
1
1
1
925381
560028-2
35176
SCREW, SET 1/4-20 X 3/8
PLATE, FRONT SWITCH
F-N-R CONTROL ASSY.......................................1.......................INCLUDES ITEMS W/%
12%
13%
14%
15%
16%
17%
18%
19%
20%
21%
22%
23%
24%
25%
25627
F-N-R CONTROL
SEAL, WEATHERPACK
CONNECTOR, MALE
1
4
1
4
4
2
1
1
1
1
1
1
1
1
405070
405046
12223
TERMINAL WEATHERPACK
NUT, HEX FINISH 1/4-28 ZINC
ROD END, 1/4-20 FEMALE RH
CABLE, CONTROL 40" X 2" STROKE
MOUNT TRANSAXLE CTRL. CABLE
SPRING, CTRL. CABLE TENSIONING
SCREW, HHC 1/4-20 X 3/4 GRD. 8
RETAINER, FNR CABLE SPRING
SCREW, HHC 1/4-20 X 7/8
6904
580001
440006
120077
565006
915003
584044
2295
440005
933240
PLATE, F-N-R PINTLE CONTROL
WASHER, FLAT SAE 1/4" GRD. 9
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 74
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 Concrete Saw — Joystick Mounting Assy.MQ SP-3035 CONCRETE SAW —
Joystick Mounting Assy.
25
11
7
5
4
2
6
13
16
21
20
23
24
20
1
20
14
18
17
8
12
15
24
1
19
9
10
22
3
26
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 75
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 Concrete Saw — Joystick Mounting Assy.MQ SP-3035 CONCRETE SAW —
Joystick Mounting Assy.
NO
1#
2#
3#
4#
5#
6#
7#
PART NO
0161D
10019
1579
2203
PART NAME
NUT, HEX FINISH 5/16-18
NUT, FYLOC #10-32
SCREW. JJC 1/4-20 X .5
WASHER, FLAT, #10
CORD GRIP, SAW FNR CONTROL
BOOT, FNR CONTROL HANDLE
SPACER, F-N-R
QTY.
REMARK
2
1
1
4
1
1
1
1
1
1
1
1
1
405053
442005-6
442006-3
442011
442012
442013
442021
442022
460018
565005
584021
584023
584024
926348
933015
933073
933225
933240
933242
938062
973735
35122
8#
9#
BELLCRANK, SAW F-N-R
PLATE, NEUTRAL DETENT
F-N-R MOUNTING PLATE
CONTROL LEVER
SPACER, F-N-R DELRIN
CAM ROLLER, SAW FNR CONTROL
10#
11#
12#
13#
14#
15#
16#
17#
18#
19#
20#
21#
22#
23#
24#
25#
26
EXTENSION SPRING F-N-R CONTROL 1
DENTENT BALL, SAW FNR CONTROL
PIN, LONG SPRING HANGER
PIN, SHORT SPRING HANGER
SCREW, SHOULDER 3/8-16 X 3/4
FRICTION DISC, SAW F-N-R
1/2 X 1-1/4 BELLEVILLE WASHER
WASHER, FENDER 1/2 X 1-1/2 ZINC
WASHER, FLAT 1/4 SAE
1
1
1
1
1
3
1
1
1
2
4
WASHER, FLAT 3/8 SAE
LOCKNUT 3/8-16 YZ
SCREW, BHSC 10-24X1-SS
F-N-R MOUNTING ASSY...........................1 ................ INCLUDES ITEMS W/#
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 76
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 Concrete Saw — Lift Pump Circuit Assy.
Lift Pump Circuit Assy.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 77
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 Concrete Saw — Lift Pump Circuit Assy.
Lift Pump Circuit Assy.
NO
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
23
24
25
26
27
28
PART NO
340011
169003
447007
21159
368817
35149
366640
35157
35156
35250
366437
35248
570050
35057
0655
933241
933240
20909
0949
480003
2621
PART NAME
PUMP, LIFT
PIN, CYLINDER
CYLINDER, LIFT
FITTING, 45 4MJ-4MO
FITTING, 90 4MJ-4MO
FITTING, ORIFICE 4MJ-4MO
FITTING, 90 4MJ-4FJ
FITTING, TEE 4MO-4MJ
HOSE ASM, 11.3"
HOSE ASM, 10.7"
FITTING, BULKHEAD #4 JIC
HOSE ASM 9.1"
CLAMP ASM #4 SINGLE HOSE
HOSE ASM 28.7"
SCREW, HHC 5/16-18 X 3/4
WASHER, FLAT SAE 5/16 GRD 9 YZ
WASHER, FLAT SAE 1/4 GRD 9 YZ
SCREW, HHC 1/4-20 X 2
NUT, HEX FINISH 1/4-20 X 3/8 NP
SEAL, OIL CR# 9815
FITTING, GREASE ZERK STR 1/4-28
SOLENOID VALVE ASM, SAW LIFT
SOLENOID, 12VDC
QTY.
1
2
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
4
1
1
1
2
REMARK
446009
400000
923000
933076
SCREW, SHC 1/4-20 X 3/8 NP
WASHER, FLAT SAE #12 ZINC
2
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 78
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 Concrete Saw — Water System Assy.
Water System Assy.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 79
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 Concrete Saw — Water System Assy.
Water System Assy.
NO
1
2
PART NO
446004
35047
PART NAME
VALVE, BALL, 1/2 BRASS
HOSE ASM, 95.1" #8LP
QTY.
REMARK
1
1
1
1
2
1
1
3
4
5
6
35052
25059
25931
26496
25827
HOSE, 1/2 ID PUSHLOCK 250 PSI, 8"
FITTING, BRASS 8 PUSH-ON 1/2 MP
FITTING, 90 8 BARB - 1/2 MP
FITTING, 90 1/2 MP - 1/2 FP
FITTING, BRASS (F) 3/4 GHT SWIVEL 1/2 MNPT
7
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 80
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 Concrete Saw — Depth Indicator Assy.
Depth Indicator Assy.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 81
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 Concrete Saw — Depth Indicator Assy.
Depth Indicator Assy.
NO PART NO
PART NAME
DEPTH INDICATOR U-BRACKET
POINTER, DEPTH
KNOB, COMFORT GRIP
FLANGE BEARING, .25ID
SCREW, BHSC, 1/4-20 X 5/8 SS
STUD, 1/4-20 X 1-3/4
NUT, NYLOC 1/4-20
SCREW, SHDLR 1/4D X 5/16L, 10-24 SCKT HD
NUT, NYLOC 10-24
QTY.
1
1
1
1
2
1
2
2
REMARK
1
2
3
4
5
6
7
8
9
125032
110031
560025
460019
973752
584025
10024
926149
1618
2
10 933240
11 540011
12 583059
13 440012
14 120243
15 0131 A
16 1579
17 565004
18 160013
19 923116
20 13287
WASHER, FLAT SAE 1/4 GRD 9 YZ
PULLEY, CABLE 1-1/4" OD X .25 SHAFT
SHIM, .020" THICK, .251" ID, .375" OD
DEPTH INDICATOR CABLE
PIVOT TAB
SCREW, HHC 1/4-20 X 3/4
SCREW, HHC 1/4-20 X 1/2
SPRING, EXTENSION
4
4
9
1
1
1
1
1
AXLE, INDICATOR SHEAVE
SCREW, SHC 8-32 X 3/4
NUT, NYLOC
1
2
2
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 82
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 Concrete Saw — Handle and Light Assy.
Handle and Light Assy.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 83
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 Concrete Saw — Handle and Light Assy.
Handle and Light Assy.
NO.
1
PART NO. PART NAME
12387
QTY.
2
REMARKS
NUT, NYLOCK 8X32
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
120206
405001
0161 C
0161 D
560023-1
560024
923199
574002
35359
405002
2532
560017
0655
LIGHT BAR, CONCRETE SAW
CONNECTOR, PLUG, 4 PIN FEMALE
WASHER, LOCK 5/16"
NUT, 5/16-18
HANDLE BAR, CONCRETE SAW
KNOB, HANDLEBAR
SCREW, SHC 8-32 X 1-1/4
CAM CLEAT
TERMINAL,FEM-SMALL 16-18 GA
CORD, LIGHT-EXTENDABLE
LIGHT ASSY., RECTANGULAR COMP.
GRIP HANDLE BAR
1
1
1
1
2
2
2
1
2
1
1
2
1
2
1
SCREW, HHC 5/16-18" X 3/4
WASHER, FLAT SAE 5/16 GRD 9 YZ
MOUNT CAM
933241
120244
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 84
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 Concrete Saw — Front/Rear Pointer Assy.
Front/Rear Pointer Assy.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 85
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 Concrete Saw — Front/Rear Pointer Assy.
Front/Rear Pointer Assy.
NO
1#
2#
3#
4#
5#
6#
7#
PART NO PART NAME
QTY.
1
1
1
1
1
1
1
4
2
2
2
2
2
1
1
2
REMARK
120045
120046
25832
110044
15503
500005
160004
582008
966166
965105
933241
0202
926006
1493
10133
1456
3233
RIGHT SIDE POINTER
LEFT SIDE POINTER
ROPE ASSY., FRONT POINTER
POINTER, FRONT 17-1/4"
KNOB, COMFORT GRIP STAR, 3/8-16 X 1
WHEEL, POINTER 6 X 1
AXLE, POINTER WHEEL
BUSHING, FLANGE,1 OD X 3/4 ID
PIN, CLEVIS 3/4 X 2
PIN, COTTER 5/32 X 1-1/2PLTD
WASHER, FLAT SAE 5/16 GRD 9 YZ
SCREW, HHC 5/16-18 X 1 ZINC
SCREW, SQHS, CP 1/4-20 X 1/2
SCREW, HHC 3/8-16 X 3.25
NUT, NYLOC 3/8-16
8#
9#
10#
11#
12#
13#
14#
15#
16#
17#
18#
19
NUT, HEX FINISH 3/8-16
WASHER, FENDER, 1.5OD X 3/8ID
WASHER, FLAT SAE 1/2 " GRD 9 YZ
FRONT POINTER ASSY...................................................1..........INCLUDES ITEMS W/#
2
2
933244
M10005
110020
0205
20
21
POINTER, REAR
SCREW, HHC 3/8-16 X 1 ZINC
1
2
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 86
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 Concrete Saw — Gauges and Controls Assy.
Gauges and Controls Assy.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 87
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 Concrete Saw — Gauges and Controls Assy.
Gauges and Controls Assy.
NO
1
2
3
4
5
6
7
8
PART NO
15171
446004
25627
560025
574002
15481
120210
TBD
PART NAME
CABLE PULL
VALVE, WATER FLOW CONTROL
F-N-R CONTROL ASSY.
KNOB, COMFORT GRIP
CAM CLEAT
CABLE, CHOKE 45"
MOUNT THROTTLE CABLE
WASHER
QTY.
1
1
1
1
1
1
1
1
REMARK
9
25634
TBD
TBD
15171
584028
926327
25634
933242
5283
35174
406001
423000
421000
406000
35125
406012
933241
923201
406019
25935
BULK HEAD ADAPTER
NUT
NUT
CABLE, PULL THROTTLE
PIVOT END, CABLE
SCREW SHDLR
BULK HEAD ADAPTOR
WASHER FLAT SAE
NUT, NYLOC 5/15
2
2
2
1
1
1
1
5
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
1
POSITRACTION UPPER LEVER ASSY. .............1.................SEE POSITRACTION ASSY.
SWITCH, IGNITION
VOLT METER
1
1
1
2
1
1
2
2
2
2
TACHOMETER
SWITCH, ROCKER
HARNESS, WIRING
MOUNTING BAR, CIRCUIT BREAKER
WASHER, FLAT SAE 5/16 GRD 9 YZ
SCREW, SHC 1/4-20 X 1/2
CIRCUIT BREAKER, 10 AMP
NUT, HEX 10-32 W/STAR WASHER
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 88
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 Concrete Saw — Front Axle Assy.
Front Axle Assy.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 89
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 Concrete Saw — Front Axle Assy.
Front Axle Assy.
NO
8
9
PART NO
913161
933243
100005
460006
16677
PART NAME
QTY.
REMARK
SCREW, HHC 7/16-14 X 2
WASHER, FLAT SAE 7/16
BEARING BACKING PLATE
BEARING, FLANGED, 1"
NUT, LOCK NUT, NYLOC 7/16
FITTING, GREASE ZERK STR
SCREW, SQHS, CP
4
8
2
2
4
2
2
1
10
11
12
13
14
15
16
17#
18#
19#
20#
21#
22
23
24
25
2621
926064
16010-1
25839
FRONT AXLE
FRONT WHEEL ASSEMBLY...................2....................INCLUDES ITEMS W/#
485002
500003
460002
M508006
576003
933246
06505-008
508005
1579
SEAL
2
2
4
2
2
2
2
2
6
WHEEL, FRONT 3" X 6"
BEARING
SPACER
SNAP RING
WASHER, FLAT SAE 5/8
SCREW, HHC 5/8-11 X 1.00
COVER, WHEEL, FRONT
SCREW, HHC 1/4-20 X 1/2
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 90
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 Concrete Saw — Depth Stop Assy.
Depth Stop Assy.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 91
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 Concrete Saw — Depth Stop Assy.
Depth Stop Assy.
NO
1
2
3
4
PART NO
35120
PART NAME
QTY.
REMARK
DEPTH STOP LEAD SCREW
WASHER, FLAT SAE 1/2
SPRING, COMPRESSION, 7/8
COLLAR, SET .50 ID
DEPTH STOP LINKAGE
PIN, CLEVIS 1/2 X 1.25 EFFECT
PIN, COTTER 5/32 X 1 PLTD
1
3
1
1
1
1
1
933244
565002
582009
442014
19974
5
6
7
965103
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 92
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 Concrete Saw — Platform Assy.
Platform Assy.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 93
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 Concrete Saw — Platform Assy.
Platform Assy.
NO
1
PART NO
25807
PART NAME
PLATFORM
QTY. REMARK
1
3
4
5
6
7
8
9
10
11
12
13
14
15
16
924287
120038
120040
3214
933244
583092
25837
SCREW, FHSC, 3/8-16 X 1-1/4,NP
CLIP, MOUNT,BLADEGUARD
SPACER, BLADEGUARD CLIP, .25 THICK
SCREW, HHC 1/2-13 X 1 1/4
6
1
2
3
3
1
1
1
1
1
1
1
1
3
WASHER, FLAT SAE 1/2 GRD 9 YZ
WASHER, LOWER BELT PROTECTOR
GUARD, LOWER BELT PROTECTOR
WASHER, STRAP LOWER BELT PROTECTOR
CLIP, RH BLADE GUARD MOUNT
GUARD, BLADE COLLAR - SLATE GREY
NUT, NYLOC 5/16-18
SCREW, SHSHLDR, 5/16-18X1/2
LEVER, CAM
WASHER, FLAT SAE 3/8 GRD 9 YZ
25820
120092
M200000
5283
926327
448002
933242
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 94
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 Concrete Saw — Drive Assy.
Drive Assy.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 95
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 Concrete Saw — Drive Assy.
Drive Assy.
NO
1
PART NO
263002
35325
PART NAME
QTY.
REMARK
TRANSAXLE ASSY. ................................................................ 1............. INCLUDES ITEMS W/%
WHEEL, POLY-11X3 ............................................................... 2............. REPLACES P/N 500011
2
3
582038
206005
35190
BUSHING, 1.0” TRANSTORQUE KEYLESS
SKID PLATE, TRANSAXLE
2
1
4
5
FAN ASSY. .............................................................................. 1............. INCLUDES ITEMS W/#
6
120078
540033
06500-020
933241
5283
BACKING PLATE, SAW TRANSAXLE
PULLEY, 4.13 X A X 18 TOOTH SPLINE
SCREW, HHC 5/16-18X2-1/2
2
1
2
4
2
8
8
1
3
6
2
1
1
1
1
1
1
1
3
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
4
4
7
8
9
WASHER, FLAT SAE 5/16 GRD 9 YZ
NUT, NYLOC 5/16-18
10
11#
12
13%
14
15
16%
17#
18#
19#
20#
21#
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
933242
1493
BDU-10L-122 PUMP MOTOR SUNSTRAND
WASHER, FLAT SAE 3/8 GRD 9 YZ
SCREW, HHC 3/8-16X3.25
25495
0202
35151
SCREW, HHC 5/16-18X4-1/2
SCREW, HHC 5/16-18X1 ZINC
MOUNTING HORN, AXLE
933201
933072
923118
583064
384001
25623
WASHER, FENDER 3/16X3/4 ZINC
WASHER, FLAT SAE #8 ZINC
SCREW, SHC 8-32X1 NP
STAND-0FF, 1.00 HEX X 1.483
FAN, 5-BLADE
CIRCLIP, RETAINER
35019
HOSE, 1/2 ID PUSHLOCK 250 PSI, 6"
FITTING, 45 8BEAD SHORT-6MO
FITTING, 90 8BARB - 6MO
370192
370162-1
368699
35054
FITTING, PLUG 6MO HEX SKT HD
HOSE, 1/2 ID PUSHLOCK 250 PSI, 22.25"
HOSE, 1/2 ID PUSHLOCK 250 PSI, 18.5"
FITTING, 90 8 BEADED HOSE X 10MO
HOSE ASM, 8.25" #6LP w/35253/370674
HOSE ASM, 32.85" #6LP w/ 368103
FITTING, TEE RUN 6MJ - 6MJ - 6FJ
CLAMP ASM, WELD, #6 DOUBLE HOSE
HOSE ASM, 22.75" #6LP w/ 370674/370674
HOSE ASM, 54.9" #6LP w/ 370674
PLATE, HYDRAULIC OIL FILTER ADAPTER
FILTER HEAD, TRANSAXLE
25976
35226
35050
35051
366692
570053
35049
35048
120260
25617
306006
144003
367470
923200
933076
923201
11780
FILTER, TRANSAXLE
RESERVOIR, HYDRAULIC OIL
FITTING, STR 4MJ - 6MO
SCREW, SHC 1/4-20 X 3/8 NP
WASHER, FLAT SAE #12 ZINC
SCREW, SHC 1/4-20 x 1/2
FITTING, 45 6MJ-6MO
1
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 96
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 Concrete Saw — Bladeshaft and Mounting Assy.
Bladeshaft and Mounting Assy.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 97
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 Concrete Saw — Bladeshaft and Mounting Assy.
Bladeshaft and Mounting Assy.
NO.
1
2#
PART NO. PART NAME
35270
25840
QTY. REMARKS
BLADESHAFT AND MOUNTING GROUP ................................ 1.......INCLUDES ITEMS W/#
BLADESHAFT ASSY. W/TACH P/U.......................................... 1.......INCLUDES ITEMS W/%
4#
5#
6#
7#
8#
9#
10#
25842
120220
120221
923357
16530
MOUNTING BLOCK, BLADESHAFT
MOUNTING BLOCK, BLADESHAFT W/PIN
SADDLE CLAMP 1.50X4.00 BLADESHAFT
SCREW, SHC 7/16-14 X 1-1/4, NP
SCREW, HHC 7/16-14 X 1
1
1
2
4
2
6
4
1
1
2
6
2
2
2
2
2
2
1
2
2
1
1
933243
06502-010 SCREW, HHC 7/16-14 X 1-1/4
25841
162000
576005
10138
486000
485001
480001
480002
578129
460008
460004
11722
969314
583026
577009
35254
WASHER, FLAT SAE 7/16 GRD 9 YZ
11#%
12#%
13#%
14#%
15#%
16#%
17#%
18#%
19#%
20#%
21#%
22#%
23#%
24#%
25#%
26#%
27#%
28#%
29#%
30#%
31#%
32#%
33#%
34#%
HOUSING, SINGLE SPEED W/TACH
BLADE SHAFT
SNAP RING, SH-156
SCREW, SHS,1/4-20 X 1/2, NP
WASHER, THRUST
SLEEVE, BLADE SHAFT SEAL
SEAL, OIL CR# 26110
SEAL, OIL CR# 16022
O-RING, SIZE 2-129 BUNA 70
BEARING, 7208BGC3
BEARING, CYLINDRICAL NU2208RC3
FITTING, 90 6MJ-6M0
KEY, WOODRUFF, #61, 3/16" X 5/8"
DRAIN PLUG, MAGNETIC, 1/2-20
GASKET, DRAIN PLUG
SENDER ASM, TACHOMETER SIGNAL GENERATOR .......... 1........INCLUDES ITEMS W/+
GEAR, SAW BLADE SHAFT SPEED PICKUP
COLLAR ASSY., OUTER BLADE SHAFT................................. 2........INCLUDES ITEMS W/@
COLLAR, INNER BLADE SHAFT
BUSHING, QUICK DISCONNECT BLADE SHAFT
SCREW, HHC 5/8-11X3 GR8
35077
1
180001
180000
582012
915315
25695
2
2
1
1
1
1
1
2
2
1
4
2
WASHER, SEALED 3/4"
SCREW, HHC 5/8-11X3 LH GR8
SNAP RING, VH0-315
GENERATOR, TACHOMETER SIGNAL
SEAL, WEATHERPACK 16-18 GA, GREEN
TERMINAL, WEATHERPACK MALE 14-16 GA
CONNECTOR, WEATHERPACK 2 MALE PIN
PIN, DOWEL 3/8 X 1-1/4"
915316
576002
35#%+ 421001
36#%+ 12171
37#%+ 12179
38#%+ 12176
39#%+@ 980705
40#%+@ 180001-1
COLLAR, BLADE OUTSIDE
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 98
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 Concrete Saw — Positraction Assy.
Positraction Assy.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 99
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 Concrete Saw — Positraction Assy.
Positraction Assy.
NO
1
PART NO
442019
560026
442020
933015
933073
19974
PART NAME
QTY.
1
1
1
1
REMARK
POSITRACTION ACTUATOR LEVER
COVER, HANDLE FLAT RED
LEVER CONNECTOR
FRICTION DISC, 1-1/2" X 1/2" X 1/8"
WASHER, BELLVIEW 1/2 X 1-1/4
PIN, CLEVIS
2
3
4
5
1
1
6
7
8
9
965103
565003
933244
25673
PIN, COTTER 5/32 X 1 PLTD
SPRING, COMPRESSION
WASHER, FLAT SAE 1/2 GRD 9 YZ
STUD, 1/2-13 X 2"
1
1
9
1
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
938064
168005
160012
460020
576012
480003
583054
242000
15207
LOCKNUT, TOP 1/2-13 YZ
POSI-TRACTON AXLE TUBE
SHAFT, POSITRACTION DRIVE
BEARING, COMPOSITE SLEEVE
SNAP RING SPIRAL
1
1
1
2
2
2
2
2
2
2
2
1
2
2
2
2
SEAL
SHIM, ARBOR- 1X1-1/2 X .093
HUB, POSITRACTION DRIVE
KEY, 1/4 SQ X 1.5
0655
35147
SCREW, HHC 5/16-18 X 3/4
WASHER, FLAT .375 I.D. X 1" O.D. X .125
POSI-TRAC LOWER CONNECTION LEVER
SCREW, HHC 3/8-16 X 1.0 GRD8
WASHER, FLAT SAE 3/8 GRD 9 YZ
BRACKET, ANGLE POSI TRAC
PLATE, CLAMPING, POSI TRAC
SCREW, HHC 1/2-13 X 1 1/2
SCREW, HHC 1/2-13 X 2
442018
915105
933242
125035
120080
5218
6159A
10176
933225
2
2
2
1
NUT, NYLOC 1/2-13
WASHER, FENDER 1/2 X 1-1/2 ZINC
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 100
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 Concrete Saw — Pulley and V-Belt Assy.
Pulley and V-Belt Assy.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 101
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 Concrete Saw — Pulley and V-Belt Assy.
Pulley and V-Belt Assy.
NO
1
PART NO
540006
540066
540065
540049
540000
540070
540012
582013
582028
582020
460030
520006
521005
25557
PART NAME
QTY. REMARKS
PULLEY, BLADESHAFT 3.8 6G 3VX1615 .............1..........16" BLADE
PULLEY, BLADESHAFT 4.0 6G 3VX2012 .............1..........20" BLADE
PULLEY, BLADESHAFT 4.2 6G 3VX2012 .............1..........26" BLADE
PULLEY, BLADESHAFT 4.4 6G 3VX1615 .............1..........30" BLADE
PULLEY, ENGINE 3.8 6G 3VX4.01A......................1..........16" BLADE
PULLEY, ENGINE 3.8 6G 3VX5.01A......................1..........20" BLADE
PULLEY, ENGINE 3.0 6G 3VX4.01A......................1..........26" AND 30" BLADE
1
1
1
2
2
2
3
KEY, 3/8" X 3/8" SQ X 2-1/4"
1
4
BUSHING, TAPER-LOCK 1615 X 1-7/16................1..........16" AND 20" BLADE, ENGINE SIDE
BUSHING, TAPER-LOCK 1615 X 1-1/2..................1..........16" AND 30" BLADE, BLADESHAFT SIDE
BUSHING, TAPER-LOCK 2012 X 1-1/2..................1..........20" AND 26" BLADE, BLADESHAFT SIDE
V-BELT, 6 3 VX 425 ..............................................1..........ALL MODELS
5
5
6
7
V-BELT, AX-31........................................................2..........ALL MODELS
BELT TENSIONER ASSY.......................................1..........INCLUDES ITEMS W/@
8
9@
10@
11@
12@
13@
14@
15
3214
SCREW, HHC 1/2-13 X 1 1/4
WASHER, FLAT SAE 1/2 GRD 9 YZ
IDLER ARM, FENNER
1
2
1
1
1
1
933244
448000
544001
540003
25716
ADAPTOR, SHOULDER, FENNER DRIVE
PULLEY, W/BRG. 4" A SECTION
SCREW, MODIFIED 1/2-13 X 1 3/4
13016
BELT DRIVE JACKSHAFT ASSY...........................1..........INCLUDES ITEMS W/$
16$
17$
18$
19$
20$
21$
22$
23$
24$
25$
26$
27
540030
925437
576003
460021
25845
PULLEY, 4.125 x .750 1A
SCREW, SHS,CP 5/16-18 x 3/8
SNAP RING - HO-185
2
4
2
2
1
2
1
1
2
1
1
1
2
2
BEARING, ROLLER # 6204 2RS
JACKSHAFT ARM
KEY, 3/16 SQ x 1.0
584013
167001
10307
JACKSHAFT, SAW BELT DRIVE
SCREW, HHC 1/2-13 X 5
933244
960102
10176
WASHER, FLAT SAE 1/2 GRD 9 YZ
FITTING, GREASE ZERK STR 1/8 MP
NUT, NYLOC 1/2-13
120081
0205
933242
MOUNT, TENSIONER
SCREW, HHC 3/8-16 X 1
WASHER, FLAT SAE 3/8 GRD 9 YZ
28
29
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 102
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 Concrete Saw — Battery Assy.
Battery Assy.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 103
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 Concrete Saw — Battery Assy.
Battery Assy.
NO
1
2
3
4
PART NO
404000
25838
19303
TBD
PART NAME
BATTERY, GROUP 26R
MOUNT, BATTERY CLAMP
CABLE, BATTERY POS 4 GA X 48" POST
CABLE, BATTERY POS
CABLE, 24" POS
QTY. REMARK
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
5
6
16782
TBD
CABLE, BATTERY NEG
7
8
9
10
11
12
13
14
15
12022
933242
933240
10133
10024
35023
1023
CABLE, BATTERY NEG 4 GA X 20" X 1/2"
WASHER, FLAT SAE 3/8 GRD 9 YZ
WASHER, FLAT SAE 1/4 GRD 9 YZ
NUT, NYLOC 3/8-16
NUT, NYLOC 1/4-20
CLAMP, LOOM CUSHIONED #10 .263 HOLE
SCREW, HHC 3/8-16 X 1 1/4 GR 5
CABLE, BATTERY NEG POST 4 GA X 32 X 3/8
BATTERY CABLE KIT
12278
TBD
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 104
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 Concrete Saw — Engine Brackets Assy.
Engine Brackets Assy.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 105
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 Concrete Saw — Engine Brackets Assy.
Engine Brackets Assy.
NO
1
2
3
4
PART NO
125034
933242
915105
125016-3
282002
300000
300000-1
300000-2
364002
10434
364003
364000
280000
2534
25719
35098
PART NAME
LIFTING RING
QTY.
1
4
4
4
1
1
1
1
1
1
1
1
1
1
1
1
REMARK
WASHER, FLAT SAE 3/8 GRD 9 YZ
SCREW, HHC 3/8-16 X 1.0 GRD8
STANDOFF, LIFTING PLATE 35HP
PREFILTER, ENGINAIRE 3" 2-20/150
AIR FILTER HOUSING, ASM
FILTER, AIR, ELEMENT, PRIMARY
FILTER, AIR, ELEMENT,SAFETY
HOSE, 2" 90 DEGREE
CLAMP, HOSE WORM 1-9/16 TO 2.0 # 32
COUPLER, HOSE INTAKE
HOSE, 2" X 1 3/4" 90 DEGREE
MUFFLER, WISCONSIN 35, STANDARD
CLAMP, MUFFLER
5#
6#
7#
8#
12#
13#
14#
15#
16
17
20
21#
22#
24
NIPPLE, EXHUAST PIPE SCH 40
CLAMP, HEAT SHRINK TUBING 2.5" - 2.75"
CLAMP, HOSE #28 1-5/16X2-1/4
962015
35182
1
AIR INTAKE GROUP ......................................................1............INCLUDES ITEMS W/#
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 106
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 Concrete Saw — Engine Installation Assy.
Engine Installation Assy.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 107
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 Concrete Saw — Engine Installation Assy.
Engine Installation Assy.
NO
1
2
3
4
5
6
7
8
PART NO
15500
25813
120079
933246
4702
06503-026
25836
913217
933244
10176
PART NAME
QTY.
REMARK
ENGINE, WISCONSIN W41770-467438R
MOUNT, JACKSHAFT PIVOT ARM
MOUNT, MOTOR TENSIONER
WASHER, FLAT SAE 5/8 GRD 9 YZ
NUT, HEX FINISH 5/8-11
SCREW, HHC 1/2-13 X 3-1/4
MOUNT, ENGINE TENSIONING
SCREW, HHC 1/2-13 X 3 1/2 GR5 WZ
WASHER, FLAT SAE 1/2 GRD 9 YZ
NUT, NYLOC 1/2-13
1
1
1
2
2
2
1
2
8
4
9
10
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 108
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 Concrete Saw — Bladeguard Assy.
Bladeguard Assy.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 109
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 Concrete Saw — Bladeguard Assy.
Bladeguard Assy.
NO
1
1
1
1
PART NO
M18100
M18140
M18180
M18220
10176
PART NAME
QTY.
REMARK
BLADE GUARD 16-INCH
BLADE GUARD 20-INCH
BLADE GUARD 26-INCH
BLADE GUARD 30-INCH
NUT, NYLOCK
1
1
1
1
1
1
2
3
3
4
5
6
7
582040
582039
362000
923144
362003
1618
BUSHING, BLADE GUARD
BUSHING, BLADE GUARD....................................... 1..................30-INCH ONLY
HOSE, WATER #6LP
SCREW, SHC 10-24X12
TUBE, WATER, LH SIDE
NUT, NYLOCK 10-24
2
4
1
4
1
3
1
1
1
9
933209
10024
WASHER, FENDER 1/4" X1-1/2" ZINC
NUT, NYLOCK 1/4-20
FLAP, MUD
SCREW, HHC 1/4"-20 X3/4"
WATER MANIFILD
WATER MANIFILD.................................................... 1..................30-INCH ONLY
SCREW, HHC 1/4"-20 X1-1/2"
TUBE, WATER, RH SIDE
FITTING, QD MALE SNAPTITE PHN4 1/4" MP
FITTING, PLUG 1/8" MP HEX SKT HD
FITTING, STR 6BARB-1/8" MP
SCREW, HHC 1/2-13 X3-1/4"
SCREW, HHC 1/2-13 X3-3/4"
FITTING, QD FEM SNAPTITE PHC4-4F
10
11
12
13
13
14
15
16
17
18
19
19
20
200019
0131 A
445002
445003
5277
36002
320010
2113
370455
06503-026
06503-030
320009
2
1
1
1
2
1
1
1
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 110
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 Concrete Saw — Optional Water Pump Kit Assy.
Optional Water Pump Kit Assy.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 111
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 Concrete Saw — Optional Water Pump Kit Assy.
Optional Water Pump Kit Assy.
NO
1
1
2
3
4
5
6
PART NO
M18100
120084
120085
342000
933242
933244
205
PART NAME
BLADE GUARD 16-INCH
DESCRIPTION
MOUNT, WATER PUMP
PUMP, WATER JABSCO
WASHER, FLAT SAE 3/8 GRD 9 YZ
WASHER, FLAT SAE 1/2 GRD 9 YZ
SCREW, HHC 3/8-16 X 1.0
QTY.
1
1
1
1
4
2
4
REMARK
7
8
9
16524
SCREW, HHC 1/2-13 X 1 1/4 GD 8
FITTING, PETCOCK RAD DRAIN 1/4MP
FITTING, BRASS 1/2FP-1MP
FITTING, BRASS 1/4FP-1/2MP
FITTING, BRASS 8 PUSH-ON-1/4MP
FITTING, 90 8BARB - 1/2 MP (4390-8-8)
PULLEY, 4.12 X 2G A
V BELT, AX-31 (GOODYEAR)
HOSE, 1/2 ID PUSHLOCK 250 PSI, 18"
HOSE, 1/2 ID PUSHLOCK 250 PSI, 13"
SWITCH, ROCKER, CH# M-58031-01
2
1
2
1
1
1
1
1
369970
366057
366956
25932
10
11
12
13
14
15
16
17
25931
540032
521005
35257
35258
406000
1
1
1
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 112
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 Concrete Saw — Collar Puller Assy.
Collar Puller Assy.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 113
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 Concrete Saw — Collar Puller Assy.
Collar Puller Assy.
NO
1#
2#
3#
4#
5#
6
PART NO
584037
584038
2549
25138
18503-I
18503
PART NAME
OUTER PULLER
PLATE, PULLER
SCREW, HHC 1/2-13 X 3
SCREW, HHC 5/8-11 X 5 TAP
COLLAR PULLER INSTRUCTION SHEET
QTY.
REMARK
1
1
3
1
1
COLLAR PULLER ..................................................... 1..................INCLUDES ITEMS W/#
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 114
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 Concrete Saw — Seal Sleeve Puller Seal/Seal Installation Tool
Seal Sleeve Puller/Seal Installation Tool
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 115
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 Concrete Saw — Seal Sleeve Puller Seal/Seal Installation Tool
Seal Sleeve Puller/Seal Installation Tool
NO PART NO
1# 35163
PART NAME
SCREW, HHC 3/8 – 16 X 4 FULL THREAD
QTY.
REMARK
1
SEAL SLEEVE & THRUST WASHER PULLER ASM ....... 1..............INCLUDES ITEMS W/#
2
M18505
3# 35162
4# 584052
5# 35161
6# 937980
7# 35164
8# 35165
9# 584050
SCREW, 10 - 24 X 6 FULL THREAD
SEAL INSTALLATION TOOL
SCREW, 10 - 24 X 12 FULL THREAD
NUT, WELD 10 - 24
SCREW, HHC 1/4 – 20 X 5
SCREW, HHC 1/4 – 20 X 10
TOOL, SEAL REMOVAL
2
1
2
2
3
3
1
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 116
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 Concrete Saw — Bushing Extension Kits
Bushing Extension Kits
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 117
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 Concrete Saw — Bushing Extension Kits
Bushing Extension Kits
BUSHING EXTENSION KIT 18501 (.375 — .75)
NO PART NO
PART NAME
DOWEL PIN, 3/8 X 2-1/4
OUTER COLLAR
QTY.
REMARK
1
2
3
4
5
926949
180003-1
582032
1
1
1
1
1
QD BUSHING 3/8 TO 3/4
5/8-11X 4 LH HEX BOLT
5/8-11X 4 RH HEX BOLT
90123445
915319
BUSHING EXTENSION KIT 18502 (.75 — 1.125)
NO PART NO
PART NAME
DOWEL PIN 3/8 X 2-1/2
OUTER COLLAR
QTY.
REMARK
1
2
3
4
5
926950
1
1
1
1
1
180003-1
582033
QD BUSHING 3/4-1-1/8
5/8-11X 4 LH HEX BOLT
5/8-11X 4 RH HEX BOLT
90123445
915319
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 118
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 Concrete Saw — Electric Schematic
ELECTRIC SCHEMATIC
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 119
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ SP-3035 Concrete Saw — Specifications
SPECIFICATIONS
Engine
Wisconsin 35 hp V-4, electronic ignition, remote oil filter and above-frame
remote oil drain
Precleaner
Centrifugal type, self-cleaning
Air Cleaner
Fuel Tank
Four-stage air filtration, cartridge element w/ safety element
5 gallon molded tank, shutoff valve and central drain
Spindle Drive Belt
Belt Tensioners
Single 6-groove premium quality 3V Cross-Section Powerband
Single-point Spindle belt tensioner, self-adjusting rotary belt tensioners
throughout for accessories
Blade Range
Max Cut Depth
Blade Guard
14“ to 30“
12.75”
Extra heavy design, slip-on type, w/quick-disconnect water hoses, usable on
either side, 20“ standard, 16”-20”-26”-30” optional
Spindle Assembly
Fully-enclosed bearings and shaft, oil bath, protected seals, 1-1/2” diameter
Spindle, remote protected oil fill and vent, blade usable on either side.
Blade Flanges
Blade Flushing
Blade Control
Quick-disconnect, taper-lock, 4.5” diameter collars w/ 24 water spray ports
Minimum water usage system, panel-mounted flow control, 24 evenly
distributed water spray ports (12 per blade side)
12-volt hydraulic raise/lower system. Joystick-controlled at the operator’s
panel with plunge and raise buttons located on the control joystick
Blade Depth Stop
Frame
Lift Point
Positive, heavy duty design w/ accurate depth gauge
Heavy gauge laser-cut steel, box design, powder coat finish
Integral balanced single-point lift
Balance
Rear pivot design for quick maneuverability
Handlebars
Front Wheels
3-position adjustable with in/out and storage positions, quick locks
6” x 3”, “no maintenance” precision sealed bearings w/ extra end seals and
seal protectors; no grease points
Rear Wheels
Drive System
11” x 3”
Hydro-Gear hydrostatic powered transaxle drive w/ infinite F-N-R speed
control, central joystick, remote filter. Cable control. Positraction w/ panel-
mounted lever.
Travel Speed
Battery
Up to 225 feet per minute
12 volt, group 26, 425 cold cranking amps
Engine Controls
Twist-lock throttle, choke, back-lit Spindle tach w/hour meter, volt meter, 3-
position ignition switch
Electrical Wiring
Night Light
Front Pointer
Rear Pointer
Tools
Easy service loom
Standard, removable, usable either side of saw
Heavy gauge frame, 6” pointer wheel, tether rope
Standard, adjustable
15/16” blade wrench standard
Unit Dimensions
46” long, 27-3/8” wide, 41” high (handlebars in storage position, w/o blade
collars)
Unit Weight
975 pounds, with oil, no fuel
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 120
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION AND PARTS MANUAL
HERE'S HOW TO GET HELP
PLEASE HAVE THE MODEL AND SERIAL
NUMBER ON-HAND WHEN CALLING
UNITED STATES
Multiquip Corporate Office
18910 Wilmington Ave.
Carson, CA 90746
MQ Parts Department
800-427-1244
310-537-3700
Tel. (800) 421-1244
Fax (800) 537-3927
Fax: 800-672-7877
Fax: 310-637-3284
Contact: [email protected]
Mayco Parts
800-306-2926
310-537-3700
Warranty Department
800-421-1244, Ext. 279 Fax: 310-537-1173
310-537-3700, Ext. 279
Fax: 800-672-7877
Fax: 310-637-3284
Service Department
800-421-1244
310-537-3700
Technical Assistance
800-478-1244
Fax: 310-537-4259
Fax: 310-631-5032
MEXICO
UNITED KINGDOM
MQ Cipsa
Multiquip (UK) Limited Head Office
Tel: (52) 222-225-9900 Hanover Mill, Fitzroy Street,
Momoxpan, Cholula, Puebla 72760 Mexico Fax: (52) 222-285-0420 Ashton-under-Lyne,
Carr. Fed. Mexico-Puebla KM 126.5
Tel: 0161 339 2223
Fax: 0161 339 3226
Contact: [email protected]
Lancashire OL7 0TL
Contact: [email protected]
CANADA
Multiquip
BRAZIL
Multiquip
4110 Industriel Boul.
Laval, Quebec, Canada H7L 6V3
Contact: [email protected]
Tel: (450) 625-2244
Fax: (450) 625-8664
Av. Evandro Lins e Silva, 840 - grupo 505 Tel: 011-55-21-3433-9055
Barra de Tijuca - Rio de Janeiro Fax: 011-55-21-3433-9055
Contact: [email protected], [email protected]
© COPYRIGHT 2006, MULTIQUIP INC.
Multiquip Inc and the MQ logo are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without written permission. All other trademarks are the
property of their respective owners and used with permission.
This manual MUST accompany the equipment at all times. This manual is considered a permanent part of the equipment and should remain with the unit if resold.
The information and specifications included in this publication were in effect at the time of approval for printing. Illustrations are based on the SP3 “Street Pro” Professional Slab
Saw. Illustrations, descriptions, references and technical data contained in this manual are for guidance only and may not be considered as binding. Multiquip Inc. reserves the right
to discontinue or change specifications, design or the information published in this publication at any time without notice and without incurring any obligations.
Your Local Dealer is:
Download from Www.Somanuals.com. All Manuals Search And Download.
|