OperatiOn and parts Manual
MOdel st2010 series
subMersible puMp
Revision #3 (12/07/12)
To find the latest revision of this
publication, visit our website at:
THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.
Download from Www.Somanuals.com. All Manuals Search And Download.
table Of COntents
illustrations
ST010TCUL Pump Assy................................... 28-29
ST2010, ST2010A/B, ST2010CUL Pump Assy.....30-33
Electric Motor Assy........................................... 34-35
st2010 series
submersible pump
Parts Ordering Procedures...................................... 3
Safety Information ................................................ 4-7
Specifications .......................................................... 8
Dimensions.............................................................. 9
General Information............................................... 10
Components .......................................................... 11
Float Switches ....................................................... 12
Float Switch (Piggy-Back) ..................................... 13
Float Switch (Control Box)................................ 14-15
Operation............................................................... 16
Control Box Installation..................................... 17-18
Clean-Up ............................................................... 19
Maintenance.......................................................... 20
Troubleshooting ..................................................... 21
Performance Curves.............................................. 22
Control Box Wiring Diagram ............................. 23-24
Motor Wiring Diagram............................................ 25
Explanation Of Code In Remarks Column............. 26
Suggested Spare Parts ......................................... 27
Terms And Conditions Of Sale — Parts ................ 36
NOTICE
Specifications and part numbers are subject to change
without notice.
page 2 —ST2010 SerieS SubmerSible pump • operaTion and parTS manual — rev. #3 (12/07/12)
Download from Www.Somanuals.com. All Manuals Search And Download.
parts Ordering prOCedures
Ordering parts has never been easier!
Choose from three easy options:
Effective:
January 1st, 2006
best deal!
order via internet (dealers only):
Order parts on-line using Multiquip’s SmartEquip website!
If you have an MQ Account, to obtain a Username
and Password, E-mail us at: parts@multiquip.
com.
I View Parts Diagrams
I Order Parts
I Print Specification Information
To obtain an MQ Account, contact your
District Sales Manager for more information.
Use the internet and qualify for a 5% discount
on Standard orders for all orders which include
complete part numbers.*
to log in and save!
Order Parts
Note: Discounts Are Subject To Change
Fax your order in and qualify for a 2% discount
on Standard orders for all orders which include
complete part numbers.*
order via Fax (dealers only):
All customers are welcome to order parts via Fax.
domestic (uS) Customers dial:
1-800-6-PARTS-7 (800-672-7877)
Note: Discounts Are Subject To Change
domestic (uS) dealers Call:
order via phone:
1-800-427-1244
non-dealer Customers:
International Customers should contact
their local Multiquip Representatives for
Parts Ordering information.
Contact your local Multiquip Dealer for
parts or call 800-427-1244 for help in
locating a dealer near you.
when ordering parts, please supply:
Ì
dealer account number
Ì
Specify preferred method of Shipment:
Ì
Ì
Ì
Ì
Ì
dealer name and address
ꢀ UPS/Fed Ex
ꢀ DHL
ꢀ Truck
I
I
Priority One
Ground
Shipping address (if different than billing address)
return Fax number
I Next Day
Second/Third Day
applicable model number
I
quantity, part number and description of each part
NOTICE
All orders are treated as Standard Orders and will
ship the same day if received prior to 3PM PST.
We aCCepT all maJor CrediT CardS!
ST2010 SerieS SubmerSible pump • operaTion and parTS manual — rev. #3 (12/07/12) — page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
safety infOrMatiOn
Do not operate or service the equipment before reading
the entire manual. Safety precautions should be followed
at all times when operating this equipment.
Failure to read and understand the safety
messages and operating instructions could
result in injury to yourself and others.
Potential hazards associated with the operation of this
equipment will be referenced with hazard symbols which
may appear throughout this manual in conjunction with
safety messages.
Symbol
Safety Hazard
SaFeTY meSSageS
Burn hazards
The four safety messages shown below will inform you
about potential hazards that could injure you or others.The
safety messages specifically address the level of exposure
to the operator and are preceded by one of four words:
danger, Warning, CauTion or noTiCe.
Electric shock hazards
Rotating parts hazards
Pressurized fluid hazards
SaFeTY SYmbolS
danger
Indicates a hazardous situation which, if not avoided,
Will result in deaTH or SeriouS inJurY.
Warning
Indicates a hazardous situation which, if not avoided,
Could result in deaTH or SeriouS inJurY.
CauTion
Indicates a hazardous situation which, if not avoided,
Could result in minor or moderaTe inJurY.
NOTICE
Addresses practices not related to personal injury.
page 4 —ST2010 SerieS SubmerSible pump • operaTion and parTS manual — rev. #3 (12/07/12)
Download from Www.Somanuals.com. All Manuals Search And Download.
safety infOrMatiOn
general SaFeTY
CauTion
NOTICE
This equipment should only be operated by trained and
qualified personnel 18 years of age and older.
never operate this equipment without proper protective
clothing, shatterproof glasses, respiratory protection,
hearing protection, steel-toed boots and other protective
devices required by the job or city and state regulations.
Whenever necessary, replace nameplate, operation and
safety decals when they become difficult read.
Manufacturer does not assume responsibility for any
accident due to equipment modifications. Unauthorized
equipment modification will void all warranties.
never use accessories or attachments that are not
recommended by Multiquip for this equipment. Damage
to the equipment and/or injury to user may result.
Avoid wearing jewelry or loose fitting clothes that may
snag on the controls or moving parts as this can cause
serious injury.
alWaYS know the location of the nearest
fire extinguisher.
never operate this equipment when not
feeling well due to fatigue, illness or when
under medication.
alWaYS know the location of the nearest
first aid kit.
never operate this equipment under the
influence of drugs or alcohol.
alWaYS know the location of the nearest phone or keep
a phone on the job site. Also, know the phone numbers
of the nearest ambulance, doctor and fire department.
This information will be invaluable in case of an
emergency.
alWaYS clear the work area of any debris, tools, etc.
that would constitute a hazard while the equipment is
in operation.
No one other than the operator is to be in the working
area when the equipment is in operation.
do noT use the equipment for any purpose other than
its intended purposes or applications.
ST2010 SerieS SubmerSible pump • operaTion and parTS manual — rev. #3 (12/07/12) — page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
safety infOrMatiOn
a torch or other source of flame. Application of heat in
this manner may heat the oil in the seal cavity above the
critical point, causing pump damage.
pump SaFeTY
danger
neveroperatetheequipmentinanexplosive
atmosphereornearcombustiblematerials.An
explosion or fire could result causing severe
bodily harm or even death.
do noT pump water with a temperature greater than
104°F.
do noT pump liquids containing acid or alkali.
alWaYS check strainer before pumping. Make sure
strainer is not clogged. Remove any large objects, dirt
or debris from the strainer to prevent clogging.
Warning
Accidental starting can cause severe injury
or death. alWaYS place the ON/OFF
switch in the OFF position.
alWaYS use a large basket strainer when pumping
water that contains large debris.
do noT place hands or fingers inside
pump when pump is running.
alWaYS flush pump (clean) after use when pumping
water concentrated with heavy debris.It is very important
to always flush the pump before turning it off to prevent
clogging.
never disconnect any emergency or
safety devices. These devices are intended for operator
safety.Disconnection of these devices can cause severe
injury, bodily harm or even death. Disconnection of any
of these devices will void all warranties.
Fix damage to machine and replace any broken parts
immediately.
alWaYS store equipment properly when it is not being
used.Equipment should be stored in a clean, dry location
out of the reach of children and unauthorized personnel.
Risk of Electric Shock - This pump has not been
investigated for use in swimming pool or marine areas.
CauTion
never lubricate components or attempt service on a
running machine.
do noT restrict the flow of the discharge hose as it may
cause the pump to overheat.
never run pump dry.
Be careful of discharge hose whipping under pressure.
alWaYS allow the machine a proper amount of time to
cool before servicing.
alWaYS check pump oil level only when pump is cool.
Expansion due to heat may cause hot oil to spray from
the oil plug when the oil plug is removed. The possibility
of severe scalding may exist.
Keep machine in proper running condition.
eleCTriCal SaFeTY
danger
NOTICE
alWaYS place the pump in an upright position on a
platform before using.The platform will prevent the pump
from burrowing itself on soft sand or mud.
The electrical voltage required to operate
pump can cause severe injury or even death
through physical contact with live circuits.
alWaYS disconnect electrical power from
pump before performing maintenance on
pump.
never operate pump on its side.
do noT allow the pump to freeze in water.
never leave an open pump chamber unattended.
alWaYS keep the machine in proper running condition.
do noT attempt to thaw out a frozen pump by using
Warning
To reduce the risk of electric shock, connect only to a
circuit protected by a Ground-Fault Circuit-Interrupter
(GFCI).
page 6 —ST2010 SerieS SubmerSible pump • operaTion and parTS manual — rev. #3 (12/07/12)
Download from Www.Somanuals.com. All Manuals Search And Download.
safety infOrMatiOn
Control box Safety
NOTICE
danger
alWaYS make certain that the voltage supplied to the
pump is correct. Always read the pump’s nameplate to
determine what the power requirements are.
alWaYS have a qualified electrician perform the control
box installation.The possibility exists of electrical shock
or electrocution.
power Cord/Cable Safety
NOTICE
danger
alWaYS mount control box in a vertical position
protected from harsh environmental elements.
never let power cords or cables lay in water.
never stand in water while AC power cord is connected
to a live power source.
liFTing SaFeTY
CauTion
never use damaged or worn cables or cords. Inspect
for cuts in the insulation.
When raising or lowering of the pump is required, always
attach an adequate rope or lifting device to the correct
lifting point (handle) on the pump.
never grab or touch a live power
cord or cable with wet hands. The
possibility exists of electrical shock,
electrocution or death.
NOTICE
do noT lift machine to unnecessary heights.
Make sure power cables are securely connected to the
motor's output receptacles. Incorrect connections may
cause electrical shock and damage to the motor.
never lift the equipment while the electric motor is
running.
Warning
TranSporTing SaFeTY
never attempt to use the power cord as a lifting or
lowering device for the pump.
NOTICE
alWaYS shut down pump before transporting.
NOTICE
alWaYS tie down equipment during transport by
securing the equipment with rope.
alWaYS make certain that proper power or extension
cord has been selected for the job. See Cable Selection
Chart in this manual.
environmenTalSaFeTY/deCommiSSioningCE
do noT pour waste or oil directly onto
the ground, down a drain or into any water
source.
grounding Safety
danger
Contact your country's Department of Public
Works or recycling agency in your area and arrange for
proper disposal of any electrical components, waste or
oil associated with this equipment.
alWaYS make sure pump is grounded.
never use gas piping as an electrical ground.
alWaYS make sure that electrical circuits are properly
grounded to a suitable earth ground (ground rod) per
the National Electrical Code (NEC) and local codes
before operating generator. Severe injury or death by
electrocution can result from operating an ungrounded
motor.
When the life cycle of this equipment is over it is
recommended that the pump casing and all other metal
parts be sent to a recycling center.
Metal recycling involves the collection of metal from
discarded products and its transformation into raw
materials to use in manufacturing a new product.
This pump is supplied with a grounding conductor and
grounding-type attachment plug. To reduce the risk of
electric shock, connect only to a properly grounded,
grounding-type receptacle.
Recyclers and manufacturers alike promote the process
of recycling metal. Using a metal recycling center
promotes energy cost savings.
ST2010 SerieS SubmerSible pump • operaTion and parTS manual — rev. #3 (12/07/12) — page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
speCifiCatiOns
Table 1. Specifications
ST-2010/ST-2010a/
model
ST-2010b
ST-2010TCul
ST-2010Cul
Submersible Pump
Cast Ductile Iron
Type
Submersible Pump
Cast Ductile Iron
Submersible Trash Pump
Cast Ductile Iron
Impeller
Discharge Size
2.00 in. (51 mm)
2.00 in. (51 mm)
2.00 in. (51 mm)
Maximum Pumping
Capacity
85 gallons/minute
(322 liters/minute)
85 gallons/minute
(322 liters/minute)
90 gallons/minute
(341 liters/minute)
Max. Solids Diameter
---
---
1.00 in. (25 mm.)
54.7 ft. (16.6 meters)
ST-2010CUL: 50 ft. (15.24 m)
Max Head
54.7 ft. (16.6 meters)
45 ft. (13.7 meters)
Power
1.0 HP (0.75 kw)
1Ø 115V
1.0 HP (0.75 kw)
1Ø 230V
1.0 HP (0.75 kw)
1Ø 115V
Voltage; Phase
Starting Amps
63 A
30 A
53 A
ST2010: 13.5 A
ST2010A: 13.5 A
ST2010CUL: 11.9A
Running Amps
6.7 A
9.4 A
Control Box (see Note 3)
CB3
CB6
CB3
Thermal Overlaod
Protection
YES
YES
YES
Rotation
CCW (Note 1)
150 cc. (Note 2)
CCW (Note 1)
150 cc. (Note 2)
CCW (Note 1)
180 cc. (Note 2)
Mechanical Oil seal
Capacity
Check Frequency
RMP (Speed)
Monthly (300 hrs.)
3550 +/- 30
Monthly (300 hrs.)
3550 +/- 30
Monthly (300 hrs.)
3550 +/- 30
Power Cable Length
Dry Net weight
50 ft. (15.2 meters)
55 lbs. (25 Kg.)
50 ft. (15.2 meters)
55 lbs. (25 Kg.)
50 ft. (15.2 meters)
77 lbs. (35 Kg.)
1. Motor Rotation – Upon start-up, the pump "kicks" in the opposite direction of motor rotation. The correct rotation is counterclockwise (CCW) as viewed from
the impeller end of the pump.
2. Mechanical Oil Seal – Use a good grade 10 weight non-detergent hydraulic oil (i.e. Shell Turbo 32 or equivalent). Fill oil cavity 75% to 85% full (allow air
space for expansion).
3. Control Box - Control box (Table 2) may be required for certain pumping applications.
Table 2. Control box Specifications
Thermal
overload
protection
Float Switch
Capability
model no.
voltage Type
ul/CSa listed
CB3
CB6
115 VAC, 60 Hz Single-Phase
230 VAC, 60 Hz Single-Phase
YES
YES
YES
YES
YES
YES
page 8 —ST2010 SerieS SubmerSible pump • operaTion and parTS manual — rev. #3 (12/07/12)
Download from Www.Somanuals.com. All Manuals Search And Download.
diMensiOns
ST2010TCul
49.21 ft.
(15 m)
10.23 in.
(260 mm.)
5.11 in.
(130 mm.)
3.14 in.
(80 mm.)
23.82 in.
(605 mm.)
NPT 2
3.54 in.
(90 mm.)
4.52 in.
(115 mm.)
4.37 in.
(111 mm.)
7.08 in.
(180 mm.)
ST2010, ST2010a, ST2010b, ST2010Cul
49.21 ft
(15m)
16.46 in
(418 mm)
6.7 in
(170 mm) Dia.
Figure 1. ST2010 Series Dimensions
ST2010 SerieS SubmerSible pump • operaTion and parTS manual — rev. #3 (12/07/12) — page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
general infOrMatiOn
This pump must always be positioned on a platform in an
upright position.never operate the pump by a suspended
rope.To prevent large solids from entering the pump, install
a wire mesh screen or similar barrier around the pump.
inTroduCTion
The Multiquip Model ST-2010 submersible pump is
designed to pump water and is used for the draining (de-
watering) of well casings construction sites, cofferdams,
manholes, transformer vaults and excavations. The ST-
2010TCUL is designed for heavily debris-laden water and
the 2-inch discharge port can handle solids up to one inch
in diameter.
If the pump was used to pump water containing mud, silt,
use clean water to flush out the pump after each use.
do noT allow the pump to run dry, as this will damage the
pump. During maintenance, dry running is permissible but
only for a few seconds.
A cast ductile iron type impeller is attached to the output
shaft of a 1 HP electric motor which provides adequate
power for general purpose pumping. This submersible
pump is supplied complete with an electric power cable,
and a discharge port which accepts a 2-inch hose.
never lift the pump by its electrical power cord. alWaYS
lift the pump by its carrying handle or attach a rope to the
carrying handle.
A pump fully submerged in liquid will not freeze, unless
the liquid freezes. do noT allow a partially submerged
pump to freeze. The expansion of water freezing in the
volute may crack the pump, causing expensive repairs. If
there is any danger of the pump being subjected to freezing
temperatures, Lift the pump from water and allow it to drain
thoroughly.
This pump is ideal for portability because of its light
weight and carrying handle. For reliability and long life, a
mechanical seal provides shaft sealing, with an oil chamber
separating the pump section from the motor.
The pump when in use, should be installed as free standing
(upright position) on its strainer base. A 2-inch discharge
hose (not supplied) should be connected to the discharge
port.The discharge hose should be adequately supported
to avoid stress on the pump.
If the pump jams or the pump rotor locks for any reason,
disconnect the pump from the power source immediately.
Allowing the pump motor to cycle ON and OFF under an
overload condition can burn out the motor.
For maximum water flow, the discharge hose should be
kept as short as possible, and with minimum elevation
above the pump. Remember as the length and/or height
of the discharge hose is increased, the flow of water will
be reduced. Also any reduction in the hose size, and any
fittings such as valves or outlet nozzles, will restrict the
water flow.
When replacement of nuts and bolts is required, use only
recommended parts as referenced in the parts section of
this manual.This pump uses metric threads. do noT use
English measurement threads.
Warning
To avoid back-siphonage when the pump is switched off,
ensure that the end of the discharge hose is installed above
the water level at the final discharge point.
Explosion or Fire Hazard exists if this
pump is used with flammable liquids. do
noT use this pump with flammable liquids.
do noT install this pump in hazardous
locations as defined by the National
Electrical Code, ANSI/NFPA 70.
When the pump is switched off, the water remaining in the
hose will run back through the pump. This can be avoided
by placing a non-return valve in the hose nearest the pump.
never use this submersible pump to pump flammable
liquids or operate in a explosive or flammable environment.
Failure to follow the above referenced precautions could
result in serious injury or death! Replace pump cord
immediately if cord becomes damaged or severed. This
pump must be installed in accordance with National Electric
Code ANSI/NFPA 70 so as to prevent moisture from
entering or accumulating with the boxes, conduit bodies
fittings, float housing or cable.
Avoid using this pump in conditions where mud, grit, silt
or other debris are present.These conditions could cause
blockage and cause excessive pump wear.
do noT install the pump directly into an area where there
is a heavy build-up of mud, grit, silt or debris.If this condition
is present, install the pump on a platform before operating.
page 10 —ST2010 SerieS SubmerSible pump • operaTion and parTS manual — rev. #3 (12/07/12)
Download from Www.Somanuals.com. All Manuals Search And Download.
COMpOnents
ST2010, ST2010a, ST2010b, ST2010Cul
ST2010TCul
6
5
7
3
2
8
9
4
1
Figure 2. Submersible Pump Components
Figure 2 shows the location of the basic components for
the ST2010 series submersible pumps. Listed below is a
brief description of each component.
power cable. Always check the cable for signs of wear.
never use a defective power cable.Replace the cable
immediately if the cable is worn or defective.
1. Strainer base — Made of chrome-plated steel which
is resistant to hardware corrosion. do noT pump
large objects or debris with this pump. This pump is
for pumping water only.Always place the strainer base
on a platform.
6. Carrying Handle — Always carry the submersible
pump by its handle. never carry the pump by its
power cord. Carrying or lifting the pump by the power
cord will cause undue stress on the cord and ultimately
the cord will become dislodged from the pump.
2. volute/impeller — Volute is constructed of cast iron
and impeller is made of cast ductile iron to minimize
wear and prolong service life.
7. Thermal overload protection — This pump is
equipped with thermal overload protection device that
will shut down the motor in the event of high operating
temperatures.The motor will automatically restart once
the temperature returns to an acceptable operating
temperature.
3. electric motor — All ST2010 series submersible
pumps utilize a 60 Hz, single-phase, 1.0 HP electric
motor. The ST2010, ST2010A, ST2010CUL and
S-2010TCUL operate at 115 VAC while the ST2010B
operates at 230VAC.Consult with a licensed electrician
before connecting motor to a power source. Observe
all city and local safety codes.
8. mechanical oil Seal — This oil-filled seal provides
lubrication when running the pump dry. never run
the pump dry. Running the pump dry will cause severe
damage to the pump.
4. discharge port — Connect a 2-inch hose to this port.
Remember to adequately support the discharge hose
to avoid stress on the pump.
9. mechanical oil Seal plug — Remove this plug to
check and add hydraulic oil (Shell 32 or equivalent)
to the oil cavity. This oil protects the mechanical seal.
Oil cavity should be full enough to cover seal spring.
5. aC power Cable — This unit is supplied with an AC
ST2010 SerieS SubmerSible pump • operaTion and parTS manual — rev. #3 (12/07/12) — page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
flOat switChes
FloaT SWiTCH THeorY
deSign FeaTureS
Mercury monitoring is a mercury-switch actuated, liquid-
level control that has proven to be more economical
and longer lasting than other types of liquid-level control
systems, easily replacing and improving upon diaphragm
switches, air bubble systems and electro-mechanical
switches most often relied upon in the past.
Constructed of rigid, durable ABS polymer ultrasonically
welded.The all-steel mercury switch is held by positioning
pins. Interior is filled with cell foam.
Suitable for most liquid environments.
Hermetically sealed.
Thick-walled non-corrosive PVC plastic enclosure.
Pressure tested to 60 ft. (18.2 meters).
Mercury switch reliability, proven to 500,000 cycles.
Standard SJO, 16-gauge, 2 conductor cord (20 ft./6.09 m).
HoW iT WorkS
There is a tilt-sensitive mercury switch hermetically sealed
within each float. As the liquid level (water) rises or falls,
the float changes its angle until the mercury switch makes
(closed, Figure 4) or breaks (open, Figure 5) the circuit.
Maximum pumping range is 120 degrees. See Figure 3
below.
Figure 4. Float Switch (Closed)
Figure 3. Pumping Range (Float Switch)
pumping range
The pumping range of the pump is determined by the float
switch tether cord. Use Table 3 as guide line to determine
your required pumping range. Pumping ranges are based
on non-turbulent conditions. Range may vary due to water
temperature and cord shape. Please note as the tether
length increases, so does the variance of the pumping
range.
Figure 5. Float Switcfh (Open)
Table 3. pumping range
6 in. 8 in.
5.08 cm. 10.16 cm. 15.24 cm. 20.32 cm. 25.4 cm. 30.48 cm. 35.56 cm. 40.64 cm.
6 in. 10 in. 14 in. 18 in. 22 in. 27 in. 31 in. 35 in.
15.24 cm. 25.4 cm. 35.56 cm. 45.72 cm. 55.88 cm. 68.58 cm. 78.74 cm. 88.9 cm.
2 in.
4 in.
10 in.
12 in.
14 in.
16 in.
Tether length
pumping range
page 12 —ST2010 SerieS SubmerSible pump • operaTion and parTS manual — rev. #3 (12/07/12)
Download from Www.Somanuals.com. All Manuals Search And Download.
flOat switCh (piggy-baCk)
2. Place the cord into the clamp as shown in Figure 6
FloaT SWiTCH
3. Secure the clamp to the discharge hose as shown in
Figure 6. DO NOT install cord under hose clamp.
Single or dual control float switches (Figure 6) can be used
for the unattended operation of the submersible pump.
When using the piggy-back power configuration (plug),
the ST-2010 series pumps DO NOT require the use of a
control box. In this configuration (piggy-back), the SW-1
(single float switch) or SW-2 (dual float switch) are required.
The illustration below is an example of a single float switch
application.
4. Using a screwdriver, tighten the hose clamp. DO NOT
over- tighten. Make sure the float cord is not allowed
to touch the excess hose clamp band during operation.
NOTICE
Figure 6 shows a single float switch application. For
dual float switch capability use a Model SW-2 mercury
type float switch.
mountingThe Float Switch
1. Determine the required cord tether length as shown in
Figure 6 and Table 3.
Figure 6. Single Float Switch Application Diagram
ST2010 SerieS SubmerSible pump • operaTion and parTS manual — rev. #3 (12/07/12) — page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
flOat switCh (COntrOl bOx)
provides watertight housing and glands to prevent water
from leaking into the box, and a float switch interface.When
using the CB3 control box, only the SW-1WOP float switch
(2) can be used (no plug, bare wires).
ConTrol box
For special remote pumping applications of the submersible
pump, a control box (Model CB3 - for ST2010, ST2010A,
ST2010CUL, and ST2010TCUL and Model CB6 - for
ST2010B) may be required.This water-resistant control box
Figure 7. CB3 Control Box abd Dual Float Switch Application Diagram
page 14 —ST2010 SerieS SubmerSible pump • operaTion and parTS manual — rev. #3 (12/07/12)
Download from Www.Somanuals.com. All Manuals Search And Download.
flOat switCh (COntrOl bOx)
Figure 8. CB6 Control Box and Dual Float Switch Application Diagram
ST2010 SerieS SubmerSible pump • operaTion and parTS manual — rev. #3 (12/07/12) — page 15
Download from Www.Somanuals.com. All Manuals Search And Download.
OperatiOn
HoSe ConneCTionS
Connect a 2-inch hose to the discharge port on the pump
as shown in Figure 9. Make sure that the hose is attached
correctly to the discharge port.
pump poWer ConneCTionS
(piggY-baCk Cord onlY)
1. Make sure the circuit breaker supplying power to the
pump is in the OFF position.
2. Connect the float switch or switches to the AC power
receptacle as shown in Figure 6.
aTTaCHing liFTing rope
Figure 10. Submersible Pump Tilted
1. Attach a suitable lifting cable (rope) to the carrying
handle (Figure 9) on the pump and lower the pump
into place.For applications where there is an excessive
amount of mud, grit or silt, the use of a support platform
is desirable.When pumping water from swimming pool
type applications where there is little or no debris, the
support platform is not required.
(Incorrect Position)
3. If all of the pump's electrical requirements have been
met, place the circuit breaker or power ON/OFF switch
in the ON position.
4. Wait a few seconds and water should begin to flow
from the discharge hose.
5. If water is not flowing from the discharge hose or not
flowing freely after a few minutes, remove the power
from the pump and check the system for leaks.
6. To stop the pump from pumping, place the circuit
breaker or ON/OFF switch in the OFF position.
danger
never grab or touch a live power cord (Figure 11).
do noT stand in water when connecting the pump's
power cord into a voltage source.The possibility exists
of electrical shock, electrocution and possibly death!
WET
HANDS
Figure 9. Submersible Pump Upright
(Correct Position)
2. Make sure the pump is always placed in an upright
position, not tilted (Figure 10).Never position the pump
directly on a soft, loose bottom. Remember to attain
maximum pumping capacity and prevent excessive
wear, position the pump so it will not burrow itself into
sand or clay.
POWER
CORD
(POWER ON)
Figure 11. Power Cord (Wet Hands)
page 16 —ST2010 SerieS SubmerSible pump • operaTion and parTS manual — rev. #3 (12/07/12)
Download from Www.Somanuals.com. All Manuals Search And Download.
COntrOl bOx installatiOn
poWer Cord requiremenTS
danger
When routing the 115VAC/230V, 60 Hz, single-phase power
via a power cord to the control box, always use the correct
wire size. Please refer to Table 4 below (Cord Length/Wire
Size) to determine the correct wire size. Incorrect wire size
can adversely affect the performance of the pump.
The ST2010 Series submersible
pumps are designed to work with a
control box.The control box contains
the necessary electronics (float
switch connections) to operate
the pump. Remember the control
box contains hazardous voltages.
Disconnect all sources of power
Table 4. Cord length and Wire Size
ampS
50 FT.
100 FT.
150 FT.
before installing or servicing.There exists the possibility
of electrocution, electric shock or burn, which can cause
severe bodily harm or even death!
6
16 AWG 16 AWG 14 AWG
16 AWG 14 AWG 12 AWG
16 AWG 14 AWG 12 AWG
14 AWG 14 AWG 12 AWG
14 AWG 12 AWG 10 AWG
12 AWG 12 AWG 10 AWG
8
10
12
14
16
CauTion
This control box should only be installed or serviced by
a licensed electrician or qualified personnel.
ConTrol box mounTing
Mount the control box in an upright vertical position. Make
sure the control box is securely fastened to a flat surface,
that is free of dust, dirt, moisture or any elements that
may contaminate or erode the electronic components of
the control box.
ConneCTing dual FloaT SWiTCH (SW-1Wop)
To ConTrol box
1. Remove the float switch input connector housing, then
route the float switch wires through the cable gland on
the control box. Attach the wires of the float switch to
the terminal block as indicated by Table 5, Figure 7
and Figure 8.
Single-pHaSe poWer inSTallaTion (inpuT)
The ST2010, ST2010A, ST2010CUL, and ST2010TCUL
submersible pumps require 115 V, 60 Hz, single-phase
power for normal operation.The ST2010B requires 230 V,
60 Hz, single-phase power.
Table 5. Float Switch Connections
If you cannot determine what your pump's power
requirements are, look at the vendor supplied identification
name tag attached to the pump or contact Multiquip's
Service/Technical Assistance department.
Float Switch
Terminal block number
TERMINAL 1 (BLACK)
TERMINAL 2 (WHITE)
STarT
CauTion
TERMINAL 7 WHITE)
TERMINAL 8 (BLACK))
STop
Applying incorrect power (voltage phasing) to the
submersible pump can cause severe damage to the
pump. Please make sure that the correct voltage and
phase are transferred to the pump at all times.
2. Tighten the connector housing to ensure a tight fit
between the cord and the connector body. This will
prevent the cable from pulling out of the terminal block
and also prevent moisture from entering the control box.
3. Determine the length of the float switch wires, then
secure float switch wires to pump discharge hose.See
Figure 3 and Table 3 to determine the pumping range.
ST2010 SerieS SubmerSible pump • operaTion and parTS manual — rev. #3 (12/07/12) — page 17
Download from Www.Somanuals.com. All Manuals Search And Download.
COntrOl bOx installatiOn
2. Remove the pump AC input connector housing from
the control box, then route the power cord through the
cable gland on the control box.
ConneCTing aC poWerToTHe ConTrol box
1. The AC power cord (input) should have three wires.
Each wire is color coded. The colors are WHITE,
BLACK and GREEN.
3. Connect the pump power cord to the contactor as
shown in Figure 7 and Table 7.
2. Remove the AC input connector housing from the
control box, then route the power cord through the
cable gland on the control box.
Table 7. aC output power Connections
to pump
Cable Wire Color
Contactor
3. Connect the AC power cord to the contactor as shown
in Figure 7 and Table 6.
BLACK
T1
Table 6. aC input power Connections
to Contactor
WHITE
T2
GREEN
GROUND
Float Switch
Terminal block number
BLACK
L1
NOTICE
WHITE
L2
Electrical connections to the power source should only
be performed by a licensed electrician or qualified
personnel.
GREEN
GROUND
4. Tighten the connector housing to ensure a tight fit
between the power cord and the connector body.This
will prevent the cable from pulling out of the terminal
block and also prevent moisture from entering the
control box.
Turning onTHe pump
1. If all of the pump's electrical requirements have been
met, place the circuit breaker or power ON/OFF switch
in the ON position.
NOTICE
2. The CB3 control box has an operation switch located
on the front cover. This switch has 3 positions; AUTO,
MANUAL and OFF. The AUTO position allows the
pump to run in an unattended mode. The MANUAL
position will let the pump run without the float switches
controlling the pump. When in the manual mode, be
careful not to let the pump run dry. Severe damage to
the pump may occur if it is allowed to run dry.
It is recommended that the power being supplied to the
control box always be connected to a circuit breaker
or a quick disconnect switch.This safety feature allows
for quick removal of power from the control box in the
event of an emergency.
5. Connect the other end of the AC power cord to the
voltage source. Remember to provide a means of
disconnecting the power from the control box (circuit
breaker or quick disconnect switch).Also make sure to
provide a good earth ground to the control box.
3. Place the operation switch in the AUTO position. The
AC power indicator lamp should be lit (ON).
4. Wait a few seconds and water should begin to flow
from the discharge hose.
ConneCTing aC poWerToTHe pump
5. If water is not flowing from the discharge hose or not
flowing freely after a few minutes, remove the power
from the pump and check the system for leaks.
1. AC power is transferred to the pump via a contactor.
The coil of the contactor is energized or de-energized
by the opening and closing of the float switch contacts.
The power cord should have three wires. Each wire
is color coded. The colors are WHITE, BLACK and
GREEN.
6. To stop the pump from pumping, place the operation
switch in the OFF position.
page 18 —ST2010 SerieS SubmerSible pump • operaTion and parTS manual — rev. #3 (12/07/12)
Download from Www.Somanuals.com. All Manuals Search And Download.
Clean-up
pump SHuT-doWn/Clean-up
1. Remove the power from the pump by turning off the
circuit breaker or switch that provides power to the
pump.Remember to make sure that hands are dry (not
wet), and feet are not standing in water when removing
disconnecting power from the pump.
2. Using the lifting rope, lift the pump up from its current
position. Remove the discharge hose from the
discharge port on the pump.
3. Remove all power cables and float switches from
the control box. Place cables and float switches in a
suitable container where they will not get damaged.
4. If the pump was used to pump mud, grit or silt, flush
vigorously with clean water.
5. Remove the pump from the water. Wipe off any mud
or debris that might have attached itself to the pump.
6. Store pump in a clean dry place away from dirt and
debris.
ST2010 SerieS SubmerSible pump • operaTion and parTS manual — rev. #3 (12/07/12) — page 19
Download from Www.Somanuals.com. All Manuals Search And Download.
MaintenanCe
5. If oil level is low, fill with SAE 10 weight non-detergent
hydraulic oil (i.e. Shell Turbo 32 or equivalent). Fill oil
cavity 75% to 85% full (allow air space for expansion).
See Table 1 for pump oil cavity capacity.
lubriCaTion
To check the oil level of the mechanical seal perform the
following:
1. Lay the pump (Figure 12) on its side with the oil plug
facing upwards.
impeller
1. Make sure the clearance between the impeller and
the friction disk is approximately .012 - .020 inches
(.304 - .508 mm.)
2. Remove oil fill plug.
3. Visually inspect oil plug hole to verify that oil cavity
is full enough to cover seal spring. Check every 300
hours. Change hydraulic oil every 6 months (1,000
hours) or as needed.
2. If impeller is defective or badly worn, replace impeller
immediately.
4. While checking the hydraulic oil level, also check the
condition of the hydraulic oil in the seal cavity.Block the
opening with a finger and roll pump to one side to drain
oil into a small transparent container. If oil is cloudy or
has water in it, drain oil from pump cavity and replace
hydraulic oil. Check the seal for wear damage.
OIL FILL
PLUG
REMOVE FILL PLUG, AND
VISUALLY INSPECT THAT
OIL CAVITY IS FULL ENOUGH
TO COVER SEAL SPRING.
LAY PUMP FLAT
ON ITS SIDE
FILL TO 75-80% CAPACITY
SEE TABLE 1 FOR FILLING
CAPACITY.
FILL WITH 10 WEIGHT NON-
DETERGENT HYDRAULIC
OIL. USE SHELL TURBO 32
OR EQUIVALENT.
CHECK HYDRAULIC OIL
EVERY 300 HOURS. CHANGE
EVERY 6 MONTHS OR AS
NEEDED.
DISCOLORATION OF OIL
(MILKY)INDICATES A LEAKING
PUMP WATER SEAL.
Figure 12. Checking Hydraulic Oil
page 20 —ST2010 SerieS SubmerSible pump • operaTion and parTS manual — rev. #3 (12/07/12)
Download from Www.Somanuals.com. All Manuals Search And Download.
trOubleshOOting
Troubleshooting (pump)
Symptom
possible problem
Solution
Check that proper voltage is being supplied to
the pump. Also check that there is an adequate
amount of current (amps) to run the pump.
Check power source circuit breaker.
Incorrect voltage/amps?
If using float switches check wiring, inspect
power cord.
Check electrical connections?
Blown power fuse?
Replace fuse, check cause of blown fuse.
Disconnect power cord and check for clogging
and improper impeller clearance. Unclog pump.
Check overload protection device.
Pump Fails To Start
Impeller locked?
Use multimeter to check motor insulation.
Insulation resistance must be greater than 15
megaohms. If resistance is low, disassemble
pump motor and bake windings to dry them.
Wet motor windings?
Check for excessive bearing wear. If worn,
replace bearings. Replace motor if defective.
Defective motor and pump bearings?
Lay hose flat unkinked. Remove clog from hose
line.
Twisted or restricted discharge hose?
Clogged pump strainer?
Clean strainer.
Use a voltmeter to check voltage while pump
is energized. Voltage must be within 10%.
Check power source (no load and load).
If an extension cord is used, make sure it
has adequate current-carrying capacity for
the required length.See Cord Length and
SizesTable.
Pump Fails to Deliver Full
Output
Low voltage?
Impeller worn?
Replace impeller.
Replace water seal.
Tighten securely.
Defective water seal?
Loose Oil Fill Plug?
Water in Seal Oil
ST2010 SerieS SubmerSible pump • operaTion and parTS manual — rev. #3 (12/07/12) — page 21
Download from Www.Somanuals.com. All Manuals Search And Download.
perfOrManCe Curves
ST2010TCUL
METERS
FT.
60
50
40
15
10
30
20
10
0
5
GALLONS
20
40
60
80
100
0
PER MINUTE
LITERS
PER MINUTE
300
200
PUMPING CAPACITY
100
ST2010CUL
60
METERS FT.
50
15
40
10
30
20
5
10
0
GALLONS
20
40
60
80
100
0
PER MINUTE
LITERS
PER MINUTE
300
200
100
PUMPING CAPACITY
ST2010, ST2010A, ST2010B
METERS
FT.
60
50
40
15
10
30
20
10
0
5
GALLONS
80
300
100
20
40
60
0
PER MINUTE
LITERS
PER MINUTE
200
PUMPING CAPACITY
100
page 22 —ST2010 SerieS SubmerSible pump • operaTion and parTS manual — rev. #3 (12/07/12)
Download from Www.Somanuals.com. All Manuals Search And Download.
COntrOl bOx wiring diagraM
CB3 CONTROL BOX WIRING DIAGRAM
CONTACTOR
WHITE
EXTERNAL 1-PHASE
(115 VAC, 60 Hz.)
POWER SOURCE
PUMP
POWER
CORD
INPUT
POWER
CORD
CIRCUIT
BREAKER
T1
L1
BLACK
WHITE
GREEN
BLACK
BLACK
L1
L2
WHITE
SUBMERSIBLE
PUMP
GREEN
GND
COIL
GREEN
POWER
ON
LAMP
GROUND
CHASSIS
GND.
T2
WHITE
L2
BLACK
OPERATION SWITCH
AUTO
CHASSIS
GND.
WHITE
BLACK
OFF
BLACK
MANUAL
BLACK
8
4
WHITE
BLACK
BLACK
7
6
5
3
2
WHITE
BLACK
1
START
FLOAT
SWITCH
(HIGH)
STOP
FLOAT
SWITCH
(LOW)
ST2010 SerieS SubmerSible pump • operaTion and parTS manual — rev. #3 (12/07/12) — page 23
Download from Www.Somanuals.com. All Manuals Search And Download.
COntrOl bOx wiring diagraM
page 24 —ST2010 SerieS SubmerSible pump • operaTion and parTS manual — rev. #3 (12/07/12)
Download from Www.Somanuals.com. All Manuals Search And Download.
MOtOr wiring diagraM
ST-2010, ST-2010A, ST-2010B, ST-2010CUL ELECTRIC MOTOR
WIRING DIAGRAM
LEAD WIRES
BLACK (LINE)
AC POWER CORD
MAIN
COIL
AUX.
COIL
U
V
WHITE (NEUTRAL)
GREEN (GROUND)
CAPACITOR
CENTRIFUGAL
SWITCH
ST2010-TCUL ELECTRIC MOTOR
WIRING DIAGRAM
LEAD WIRES
BLACK (LINE)
AC POWER CORD
MAIN
COIL
AUX.
COIL
U
V
WHITE (NEUTRAL)
GREEN (GROUND)
CAPACITOR
CAPACITOR
CENTRIFUGAL
SWITCH
ST2010 SerieS SubmerSible pump • operaTion and parTS manual — rev. #3 (12/07/12) — page 25
Download from Www.Somanuals.com. All Manuals Search And Download.
explanatiOn Of COde in reMarks COluMn
The following section explains the different symbols and
qTY. Column
remarks used in the Parts section of this manual. Use the
help numbers found on the back page of the manual if there
are any questions.
numbers used — Item quantity can be indicated by a
number, a blank entry, or A/R.
A/R (As Required) is generally used for hoses or other
parts that are sold in bulk and cut to length.
NOTICE
The contents and part numbers listed in the parts
section are subject to change without notice.Multiquip
does not guarantee the availability of the parts listed.
A blank entry generally indicates that the item is not sold
separately.Other entries will be clarified in the“Remarks”
Column.
Sample parTS liST
remarkS Column
no. parT no. parT name
qTY. remarkS
Some of the most common notes found in the “Remarks”
Column are listed below. Other additional notes needed
to describe the item can also be shown.
1
2%
12345
BOLT .....................1 .....INCLUDES ITEMS W/%
WASHER, 1/4 IN. ..........NOT SOLD SEPARATELY
WASHER, 3/8 IN. ..1 .....MQ-45T ONLY
2% 12347
3
4
12348
12349
HOSE ..................A/R ...MAKE LOCALLY
BEARING ..............1 .....S/N 2345B AND ABOVE
assembly/kit — All items on the parts list with the
same unique symbol will be included when this item is
purchased.
no. Column
Indicated by:
unique Symbols — All items with same unique
symbol
“INCLUDES ITEMS W/(unique symbol)”
(@, #, +, %, or >) in the number column belong to the
same assembly or kit, which is indicated by a note in the
“Remarks” column.
Serial number break — Used to list an effective serial
number range where a particular part is used.
Indicated by:
duplicate item numbers — Duplicate numbers indicate
multiple part numbers, which are in effect for the same
general item, such as different size saw blade guards in
use or a part that has been updated on newer versions
of the same machine.
“S/N XXXXX AND BELOW”
“S/N XXXX AND ABOVE”
“S/N XXXX TO S/N XXX”
Specific model number use — Indicates that the part
is used only with the specific model number or model
number variant listed. It can also be used to show a
part is NOT used on a specific model or model number
variant.
NOTICE
When ordering a part that has more than one item
number listed, check the remarks column for help in
determining the proper part to order.
Indicated by:
“XXXXX ONLY”
“NOT USED ON XXXX”
parT no. Column
numbers used — Part numbers can be indicated by a
number, a blank entry, or TBD.
“make/obtain locally” — Indicates that the part can
be purchased at any hardware shop or made out of
available items.Examples include battery cables, shims,
and certain washers and nuts.
TBD (To Be Determined) is generally used to show a
part that has not been assigned a formal part number
at the time of publication.
“not Sold Separately”— Indicates that an item cannot
be purchased as a separate item and is either part of an
assembly/kit that can be purchased, or is not available
for sale through Multiquip.
A blank entry generally indicates that the item is not sold
separately or is not sold by Multiquip. Other entries will
be clarified in the “Remarks” Column.
page 26 —ST2010 SerieS SubmerSible pump • operaTion and parTS manual — rev. #3 (12/07/12)
Download from Www.Somanuals.com. All Manuals Search And Download.
suggested spare parts
ST-2010 SerieS SubmerSible pump
1 To 3 uniTS
qty.
p/n
description
1 ...........0202010T120 .......ACCORD WITH GLAND
1............0202010T081 ......OIL SEAL
1............0202010T112 .......OIL SEAL
1............0202010T008 .......PACKING, CASING
1............0202010T060 .......MECHANICAL SEAL
1............0202010T074 .......PACKING
1............0202010T157 .......PACKING
1............0202010T003 .......IMPELLER
NOTICE
Part numbers on this Suggested Spare Parts list may
supersede/replace the part numbers shown in the
following parts lists.
ST2010 SerieS SubmerSible pump • operaTion and parTS manual — rev. #3 (12/07/12) — page 27
Download from Www.Somanuals.com. All Manuals Search And Download.
st2010tCul puMp assy.
128
127
128
236
120
121
158
224
123
125
156
122
157
820
828
34
445
238
42
23
7
446
119
76
81
448
65
160
447
3
5
8
4
24
16
6
74
112
60
1
530
531
page 28 —ST2010 SerieS SubmerSible pump • operaTion and parTS manual — rev. #3 (12/07/12)
Download from Www.Somanuals.com. All Manuals Search And Download.
st2010tCul puMp assy.
no.
1
3
4
5
6
7
8
16
23
24
34
42
60
65
74
76
81
112
119
120
121
122
123
125
127
128
156
157
158
160
224
236
445
446
447
448
820
238
828
530
531
parT no.
parT name
CASING
IMPELLER
IMPELLER NUT
SPRING WASHER
IMPELLER KEY
CASING COVER
CASING PACKING
SHAFT
qTY.
1
1
1
1
1
1
1
1
1
1
3
2
1
1
1
3
1
1
1
1
1
1
1
2
1
2
1
1
4
1
1
1
1
1
1
1
1
4
4
1
3
remarkS
0202005T001
0202010T003
0202005T004
0202005T005
0202005T006
0202010T007
0202005T008
0202010T016
0202005T023
0202005T024
0202010T034
0202005T042
0202005T060
0202005T065
0202010T074
0202005T076
0202005T081
0202010T112
COMPANION FLANGE
PACKING
BOLT
BOLT
MECHANICAL SEAL
PLUG
PACKING
BOLT
OIL SEAL
OIL SEAL
0202010TCUL119 MOTOR
AC CORD W/ CORD GLAND
0202010T120
0202010T121
0202010T122
0202010T123
0202005T125
0202010T127
0202010T128
0202010T156
0202010T157
0202010T158
0202005T160
0202005T224
0202010T236
0202010T4551
0202010T446
0202010T447
0202010T4552
0202010T820
0202010T238
0202010T828
0202005T530
0202005T531
CORD CLAMP
HANGER METAL
CHAIN
SCREW
CARRYING HANDLE
SCREW
HEAD COVER
PACKING
BOLT
SLEEVE
PLUG
S-TIP
CONDENSER STARTING
AUTO-CUT (PROTECTOR)
CENTRIFUGAL SWITCH
CONDENSER RUNNING
MOUNTING PLATE, CONDENSER
STANDOFF
BOLT
BOTTOM PLATE
BOLT
ST2010 SerieS SubmerSible pump • operaTion and parTS manual — rev. #3 (12/07/12) — page 29
Download from Www.Somanuals.com. All Manuals Search And Download.
st2010, st2010a, st2010b, st2010Cul puMp assy.
265
266
263
641
121
120
236
125
563
103
123
122
174
60
65
131
214-1
224
1
132
474
299
129
179
445
446
119
81
130
447
160
47
3
6
5
4
214-2
8
176
177
112
146
147
page 30 —ST2010 SerieS SubmerSible pump • operaTion and parTS manual — rev. #3 (12/07/12)
Download from Www.Somanuals.com. All Manuals Search And Download.
st2010, st2010a, st2010b, st2010Cul puMp assy.
no.
1
3
parT no.
0202005A001
parT name
CASING
qTY.
remarkS
1
0202010CUL003 IMPELLER .........................................................1................ST2010CUL ONLY
3
3
0202010A003
0202010003
IMPELLER .........................................................1................ST2010A ONLY
IMPELLER .........................................................1................ST2010, ST2010B ONLY
4
5
6
8
47
47
60
65
81
0201503A004
0201503A005
0201503A006
0201503UL008
0201503A047A
0201503A047B
0201503A060
0201503A065
0201503A081
0202005A102
0201503A103
0201503A112
0202010119
0202010A119
0202010B119
0202010UL119
0202010120
0202010A120
0202010B120
0202010UL120
0201503A121
0201503A122
0201503A123
0201503A125
0202010127
0202010A127
0201503A127
0202005129
0202005A129
0202005UL130
0202010131
0202010A131
0201503A132
0210503A146
0201503A147
0201503A160
0202010174
IMPELLER NUT
IMPELLER NUT WASHER
IMPELLER KEY
CASING PACKING
LINER (0.2MM)
LINER (0.3MM)
MECHANICAL SEAL
PLUG
1
1
1
1
1
1
1
1
1
OIL SEAL
102
103
112
119
119
119
119
120
120
120
120
121
122
123
125
127
127
127
129
129
130
131
131
132
146
147
160
174
174
174
DISCHARGE PORT...........................................1................ ST2010A/B, ST2010CUL ONLY
PACKING ...........................................................1................ST2010A/B, ST2010CUL ONLY
OIL SEAL FOR OIL CHAMBER.........................1................ST2010A/B, ST2010CUL ONLY
MOTOR..............................................................1................ST2010 ONLY
MOTOR..............................................................1................ST2010A ONLY
MOTOR..............................................................1................ST2010B ONLY
MOTOR..............................................................1................ST2010CUL ONLY
AC CORD W/CORD GLAND .............................1................ST2010 ONLY
AC CORD W/CORD GLAND .............................1................ST2010A ONLY
AC CORD W/CORD GLAND .............................1................ST2010B ONLY
AC CORD W/CORD GLAND .............................1................ST2010CUL ONLY
CORD CLAMP
HANGER METAL
CHAIN
1
1
1
2
SCREW
CARRYING HANDLE.........................................1................ST2010 ONLY
CARRYING HANDLE.........................................1................ST2010A ONLY
CARRYING HANDLE.........................................1................ST2010B, ST2010CUL ONLY
FRAME COVER.................................................1................ST2010 ONLY
FRAME COVER.................................................1................ST2010A/B, ST2010CUL ONLY
PACKING
BOLT..................................................................4................ST2010 ONLY
BOLT..................................................................4................ST2010A/B, ST2010CUL ONLY
1
SPRING WASHER
STRAINER
BOLT
4
1
3
1
SLEEVE
OUTER PIPE .....................................................1................ST2010 ONLY
OUTER PIPE .....................................................1................ST2010A ONLY
OUTER PIPE .....................................................1................ST2010B, ST2010CUL ONLY
0202010A174
0202010UL174
ST2010 SerieS SubmerSible pump • operaTion and parTS manual — rev. #3 (12/07/12) — page 31
Download from Www.Somanuals.com. All Manuals Search And Download.
st2010, st2010a, st2010b, st2010Cul puMp assy.
265
266
263
641
121
120
236
125
563
103
123
122
174
60
65
131
214-1
224
1
132
474
299
129
179
445
446
119
81
130
447
160
47
3
6
5
4
214-2
8
176
177
112
146
147
page 32 —ST2010 SerieS SubmerSible pump • operaTion and parTS manual — rev. #3 (12/07/12)
Download from Www.Somanuals.com. All Manuals Search And Download.
st2010, st2010a, st2010b, st2010Cul puMp assy.
no.
176
176
176
177
178
179
parT no.
0202010CUL176 SUCTION COVER.............................................1................ST2010CUL ONLY
parT name
qTY.
remarkS
0202005176
0202005A176
0201503A177
0201503A178
0202005A179
SUCTION COVER.............................................1................ST2010, ST2010B ONLY
SUCTION COVER.............................................1................ST2010A ONLY
BOLT
SPRING WASHER.............................................4................ST2010, ST2010A ONLY
4
PACKING
1
1
1
1
1
214-1 0201503UL214A PACKING
214-2 0201503A214B
PACKING
PLUG
S-TIP
224
236
263
265
266
299
299
299
431
445
445
445
446
446
446
446
447
447
447
474
475
563
641
0201503A224
0202005S236
0401450080
011206020
WASHER ...........................................................2................ST2010A/B, ST2010CUL ONLY
BOLT
WASHER
4
4
952404470
0202005299
0202005A299
0202010299
0202010A431
0202010445
0202010A445
0202010B445
0202010446
0202010A446
0202010B446
0202010UL446
0202005447
0202010A447
0202005A447
0201503A474
0202010475
0201503A563
030208200
SCREW 5 X 30 ..................................................4................ST2010B, ST2010CUL ONLY
SCREW 6MM X 40MM ......................................4................ST2010A ONLY
SCREW..............................................................4................ST2010 ONLY
NUT....................................................................2................ST2010A/B, ST2010CUL ONLY
CONDENSER ...................................................1................ST2010 ONLY
CONDENSER ...................................................1................ST2010A,ST-2010CUL ONLY
CONDENSER....................................................1................ST2010B ONLY
AUTO-CUT.........................................................1................ST2010 ONLY
AUTO-CUT.........................................................1................ST2010A ONLY
AUTO-CUT.........................................................1................ST2010B ONLY
AUTO-CUT.........................................................1................ST2010CUL ONLY
CENTRIFUGAL SWITCH ..................................1................ST2010 ONLY
CENTRIFUGAL SWITCH ..................................1................ST2010A ONLY
CENTRIFUGAL SWITCH ..................................1................ST2010B,ST2010CUL ONLY
WASHER
ROPE.................................................................1................ST2010 ONLY
4
SPLIT PIN..........................................................2................ST2010A/B, ST2010CUL ONLY
SPRING WASHER.............................................4................ST2010B,ST2010CUL ONLY
ST2010 SerieS SubmerSible pump • operaTion and parTS manual — rev. #3 (12/07/12) — page 33
Download from Www.Somanuals.com. All Manuals Search And Download.
eleCtriC MOtOr assy.
page 34 —ST2010 SerieS SubmerSible pump • operaTion and parTS manual — rev. #3 (12/07/12)
Download from Www.Somanuals.com. All Manuals Search And Download.
eleCtriC MOtOr assy.
no.
112
parT no.
parT name
OIL SEAL
MOTOR A BRACKET
MOTOR B BRACKET
MOTOR ROTOR
qTY.
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
remarkS
0202010T112
0202010T268
0202010T269
0202010T270
0202010T273
*
268
269
270
273
*
*
*
*
MOTOR STATOR
445-1 0202010T4451
CONDENSER (STARTING)
CONDENSER (RUNNING)
AUTO-CUT (PROTECTOR)
CENTRIFUGAL SWITCH-1
CENTRIFUGAL SWITCH-2
SNAP RING
*
445-2 0202010T4452
446
*
447-1 0202010T4471
0202010T446
*
447-2 0202010T4472
*
*
539
540
606
607
608
822
A
0202010T539
0202010T540
0202010T606
0202010S607
0202010T608
0202010T822
0202010T119
*
*
*
*
*
*
A PACKING
MOTOR A BEARING
MOTOR B BEARING
WAVE WASHER
BRACKET RING
MOTOR ASSEMBLY..........................................1................INCLUDES ITEMS W/
*
ST2010 SerieS SubmerSible pump • operaTion and parTS manual — rev. #3 (12/07/12) — page 35
Download from Www.Somanuals.com. All Manuals Search And Download.
terMs and COnditiOns Of sale — parts
5. Parts must be in new and resalable
condition, in the original Multiquip
package (if any), and with Multiquip part
numbers clearly marked.
Multiquip reserves the right to quote and
sell direct to Government agencies, and to
Original Equipment Manufacturer accounts
who use our products as integral parts of their
own products.
paYmenT TermS
Terms of payment for parts are net 30 days.
FreigHT poliCY
6. The following items are not returnable:
All parts orders will be shipped collect or
prepaid with the charges added to the invoice.
All shipments are F.O.B. point of origin.
Multiquip’s responsibility ceases when a
signed manifest has been obtained from the
carrier, and any claim for shortage or damage
must be settled between the consignee and
the carrier.
a. Obsolete parts. (If an item is in the
price book and shows as being
replaced by another item, it is
obsolete.)
SpeCial expediTing ServiCe
A $35.00 surcharge will be added to the
invoice for special handling including bus
shipments, insured parcel post or in cases
where Multiquip must personally deliver the
parts to the carrier.
b. Any parts with a limited shelf life
(such as gaskets, seals, “O” rings,
and other rubber parts) that were
purchased more than six months
prior to the return date.
limiTaTionS oF Seller’S liabiliTY
minimum order
Multiquip shall not be liable hereunder for
damages in excess of the purchase price of
the item with respect to which damages are
claimed, and in no event shall Multiquip be
liable for loss of profit or good will or for any
other special, consequential or incidental
damages.
The minimum charge for orders from Multiquip
is $15.00 net. Customers will be asked for
instructions regarding handling of orders not
meeting this requirement.
c. Any line item with an extended
dealer net price of less than
$5.00.
d. Special order items.
reTurned goodS poliCY
e. Electrical components.
f. Paint, chemicals, and lubricants.
g. Decals and paper products.
h. Items purchased in kits.
Return shipments will be accepted and
credit will be allowed, subject to the following
provisions:
limiTaTion oF WarranTieS
No warranties, express or implied, are
made in connection with the sale of parts or
trade accessories nor as to any engine not
manufactured by Multiquip. Such warranties
made in connection with the sale of new,
complete units are made exclusively by a
statement of warranty packaged with such
units, and Multiquip neither assumes nor
authorizes any person to assume for it
any other obligation or liability whatever in
connection with the sale of its products. Apart
from such written statement of warranty,
there are no warranties, express, implied or
statutory, which extend beyond the description
of the products on the face hereof.
1. A Returned Material Authorization
must be approved by Multiquip prior to
shipment.
7. The sender will be notified of any material
received that is not acceptable.
8. Such material will be held for five
working days from notification, pending
instructions. If a reply is not received
within five days, the material will be
returned to the sender at his expense.
2. To obtain a Return Material Authorization,
a list must be provided to Multiquip
Parts Sales that defines item numbers,
quantities, and descriptions of the items
to be returned.
9. Credit on returned parts will be issued
at dealer net price at time of the original
purchase, less a 15% restocking
charge.
a. The parts numbers and descriptions
must match the current parts price
list.
b. The list must be typed or computer
generated.
10. In cases where an item is accepted, for
which the original purchase document
can not be determined, the price will be
based on the list price that was effective
twelve months prior to the RMA date.
c. The list must state the reason(s)
for the return.
Effective: February 22, 2006
d. The list must reference the sales
order(s) or invoice(s) under
which the items were originally
purchased.
11. Credit issued will be applied to future
purchases only.
priCing and rebaTeS
e. The list must include the name
and phone number of the person
requesting the RMA.
Prices are subject to change without prior
notice. Price changes are effective on a
specific date and all orders received on or
after that date will be billed at the revised price.
Rebates for price declines and added charges
for price increases will not be made for stock
on hand at the time of any price change.
3. AcopyoftheReturnMaterialAuthorization
must accompany the return shipment.
4. Freight is at the sender’s expense. All
parts must be returned freight prepaid to
Multiquip’s designated receiving point.
page 36 —ST2010 SerieS SubmerSible pump • operaTion and parTS manual — rev. #3 (12/07/12)
Download from Www.Somanuals.com. All Manuals Search And Download.
nOtes
ST2010 SerieS SubmerSible pump • operaTion and parTS manual — rev. #3 (12/07/12) — page 37
Download from Www.Somanuals.com. All Manuals Search And Download.
OperatiOn and parts Manual
HERE’S HOW TO GET HELP
PLEASE HAVE THE MODEL AND SERIAL
NUMBER ON-HAND WHEN CALLING
United StateS
Multiquip Corporate Office
MQ Parts Department
18910 Wilmington Ave.
Carson, CA 90746
Contact: [email protected]
Tel. (800) 421-1244
Fax (310) 537-3927
800-427-1244
310-537-3700
Fax: 800-672-7877
Fax: 310-637-3284
Service Department
Warranty Department
800-421-1244
310-537-3700
Fax: 310-537-4259
Fax: 310-943-2238
800-421-1244
310-537-3700
Fax: 310-943-2249
Technical Assistance
800-478-1244
mexico
United Kingdom
MQ Cipsa
Multiquip (UK) Limited Head Office
Carr. Fed. Mexico-Puebla KM 126.5
Momoxpan, Cholula, Puebla 72760 Mexico
Contact: [email protected]
Tel: (52) 222-225-9900
Unit 2, Northpoint Industrial Estate, Tel: 0161 339 2223
Fax: (52) 222-285-0420 Globe Lane,
Dukinfield, Cheshire SK16 4UJ
Contact: [email protected]
Fax: 0161 339 3226
Canada
Multiquip
4110 Industriel Boul.
Laval, Quebec, Canada H7L 6V3
Contact: [email protected]
Tel: (450) 625-2244
Tel: (877) 963-4411
Fax: (450) 625-8664
© COPYRIGHT 2012, MULTIQUIP INC.
Multiquip Inc, the MQ logo are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without written permission. All other trademarks are the property
of their respective owners and used with permission.
This manual MUsT accompany the equipment at all times. This manual is considered a permanent part of the equipment and should remain with the unit if resold.
The information and specifications included in this publication were in effect at the time of approval for printing. Illustrations, descriptions, references and technical data contained in
this manual are for guidance only and may not be considered as binding. Multiquip Inc. reserves the right to discontinue or change specifications, design or the information published
in this publication at any time without notice and without incurring any obligations.
Your Local Dealer is:
Download from Www.Somanuals.com. All Manuals Search And Download.
|