OPERATION AND PARTS MANUAL
SERIES
MODEL MVH306GH
REVERSIBLE PLATE COMPACTOR
(HONDA GX270K1SMX2 GASOLINE ENGINE)
Revision #8 (01/31/14)
To find the latest revision of this
publication, visit our website at:
THIS MANUAL MUST ACCOMPANYTHE EQUIPMENT AT ALLTIMES.
Download from Www.Somanuals.com. All Manuals Search And Download.
PROPOSITION 65 WARNING
PAGE 2 — MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14) — PAGE 3
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
HONDA GX270K1SMX2 GASOLINE ENGINE
MIKASA MVH306GH
REVERSIBLE PLATE
COMPACTOR
Air Cleaner Assembly......................................... 46-47
Camshaft Assembly ........................................... 48-49
Carburetor Assembly ......................................... 50-51
Control Assembly ............................................... 52-53
Crankcase Cover Assembly............................... 54-55
Crankshaft Assembly ......................................... 56-57
Cylinder Barrel Assembly................................... 58-59
Cylinder Head Assembly .................................... 60-61
Fan Cover Assembly .......................................... 62-63
Flywheel Assembly ............................................ 64-65
Fuel Tank Assembly ........................................... 66-67
Ignition Coil Assembly ........................................ 68-69
Muffler Assembly ............................................... 70-71
Piston Assembly................................................. 72-73
Recoil Starter Assembly..................................... 74-75
Labels Assembly ................................................ 76-77
Proposition 65 Warning ..............................................2
Table Of Contents ......................................................4
Parts Ordering Procedures ........................................5
Safety Information................................................ 6-10
Specifications ...........................................................11
Dimensions ..............................................................12
General Information .................................................13
Components.............................................................14
Inspection........................................................... 16-17
Operation ........................................................... 18-21
Maintenance ...................................................... 22-25
Troubleshooting (Engine).........................................26
Troubleshooting (Compactor) ..................................27
Terms and Conditions Of Sale — Parts .................. 78
PARTS ILLUSTRATIONS
Explanation Of Code In Remarks Column ...............28
Suggested Spare Parts ............................................29
Nameplate and Decals....................................... 30-31
Vibrating Plate Assembly ................................... 32-33
Base and Engine Assembly ............................... 34-37
Vibrator Assembly .............................................. 38-39
Control Handle Assembly .................................. 40-43
Hand Pump Assembly........................................ 44-45
NOTICE
Specification and part number are subject to
change without notice.
PAGE 4 — MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS ORDERING PROCEDURES
Ordering parts has never been easier!
Choose from three easy options:
Effective:
January 1st, 2006
Best Deal!
Order via Internet (Dealers Only)
Order parts on-line using Multiquip’s SmartEquip website!
:
If you have an MQ Account, to obtain a Username
and Password, E-mail us at: parts@multiquip.
com.
■ View Parts Diagrams
■ Order Parts
■ Print Specification Information
To obtain an MQ Account, contact your
District Sales Manager for more information.
Use the internet and qualify for a 5% Discount
on Standard orders for all orders which include
complete part numbers.*
to log in and save!
Order Parts
Note: Discounts Are Subject To Change
Fax your order in and qualify for a 2% Discount
on Standard orders for all orders which include
complete part numbers.*
Order via Fax (Dealers Only)
:
All customers are welcome to order parts via Fax.
Domestic (US) Customers dial:
1-800-6-PARTS-7 (800-672-7877)
Note: Discounts Are Subject To Change
Domestic (US) Dealers Call:
Order via Phone:
1-800-427-1244
Non-Dealer Customers:
International Customers should contact
their local Multiquip Representatives for
Parts Ordering information.
Contact your local Multiquip Dealer for
parts or call 800-427-1244 for help in
locating a dealer near you.
When ordering parts, please supply:
❒
Dealer Account Number
❒
Specify Preferred Method of Shipment:
❒
❒
❒
❒
❒
Dealer Name and Address
✓ UPS/Fed Ex
✓ DHL
✓ Truck
■
■
Priority One
Ground
Shipping Address (if different than billing address)
Return Fax Number
■ Next Day
Second/Third Day
Applicable Model Number
■
Quantity, Part Number and Description of Each Part
NOTICE
All orders are treated as Standard Orders and will
ship the same day if received prior to 3PM PST.
WE ACCEPT ALL MAJOR CREDIT CARDS!
MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14) — PAGE 5
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INFORMATION
Do not operate or service the equipment before reading
the entire manual. Safety precautions should be followed
at all times when operating this equipment.
Failure to read and understand the safety
messages and operating instructions could
result in injury to yourself and others.
Potential hazards associated with the operation of this
equipment will be referenced with hazard symbols which
may appear throughout this manual in conjunction with
safety messages.
SAFETY MESSAGES
The four safety messages shown below will inform you
about potential hazards that could injure you or others.The
safety messages specifically address the level of exposure
to the operator and are preceded by one of four words:
DANGER,WARNING, CAUTION or NOTICE.
SAFETY SYMBOLS
DANGER
Indicates a hazardous situation which, if not avoided,
WILL result in DEATH or SERIOUS INJURY.
WARNING
Indicates a hazardous situation which, if not avoided,
COULD result in DEATH or SERIOUS INJURY.
CAUTION
Indicates a hazardous situation which, if not avoided,
COULD result in MINOR or MODERATE INJURY.
NOTICE
Addresses practices not related to personal injury.
PAGE 6 — MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INFORMATION
GENERAL SAFETY
CAUTION
NOTICE
This equipment should only be operated by trained and
qualified personnel 18 years of age and older.
NEVER operate this equipment without proper protective
clothing, shatterproof glasses, respiratory protection,
hearing protection, steel-toed boots and other protective
devices required by the job or city and state regulations.
Whenever necessary, replace nameplate, operation and
safety decals when they become difficult read.
Manufacturer does not assume responsibility for any
accident due to equipment modifications. Unauthorized
equipment modification will void all warranties.
NEVER use accessories or attachments that are not
recommended by Multiquip for this equipment. Damage
to the equipment and/or injury to user may result.
NEVER operate this equipment when not
feeling well due to fatigue, illness or when
under medication.
ALWAYS know the location of the nearest
fire extinguisher.
NEVER operate this equipment under the influence of
drugs or alcohol.
ALWAYS know the location of the nearest
first aid kit.
ALWAYS know the location of the nearest phone or keep
a phone on the job site. Also, know the phone numbers
of the nearest ambulance,doctor and fire department.
This information will be invaluable in the case of an
emergency.
ALWAYS check the equipment for loosened threads or
bolts before starting.
DO NOT use the equipment for any purpose other than
its intended purposes or applications.
ALWAYS clear the work area of any debris, tools, etc.
that would constitute a hazard while the equipment is
in operation.
MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14) — PAGE 7
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INFORMATION
COMPACTOR SAFETY
DANGER
WARNING
DO NOT place hands or fingers inside engine
compartment when engine is running.
NEVER operate the equipment in an explosive
atmosphere or near combustible materials.An
explosion or fire could result causing severe
bodily harm or even death.
NEVER operate the engine with heat shields or
guards removed.
Keep fingers, hands hair and clothing away
from all moving parts to prevent injury.
WARNING
NEVER disconnect any emergency or safety devices.
These devices are intended for operator safety.
Disconnection of these devices can cause severe injury,
bodily harm or even death.Disconnection of any of these
devices will void all warranties.
DO NOT remove the radiator cap while the
engine is hot. High pressure boiling water will gush out
of the radiator and severely scald any persons in the
general area of the compactor.
DO NOT remove the coolant drain plug
while the engine is hot. Hot coolant will
gush out of the coolant tank and severely
scald any persons in the general area of
the compactor.
CAUTION
NEVER lubricate components or attempt service on a
running machine.
NOTICE
DO NOT remove the engine oil drain plug while the
engine is hot. Hot oil will gush out of the oil tank and
severely scald any persons in the general area of the
compactor.
ALWAYS keep the machine in proper running condition.
Fix damage to machine and replace any broken parts
immediately.
CAUTION
ALWAYS store equipment properly when it is not being
used.Equipment should be stored in a clean, dry location
out of the reach of children and unauthorized personnel.
NEVER touch the hot exhaust manifold,
muffler or cylinder.Allow these parts to cool
before servicing equipment.
ENGINE SAFETY
DANGER
NOTICE
NEVER run engine without an air filter or with a dirty air
filter.Severe engine damage may occur.Service air filter
frequently to prevent engine malfunction.
The engine fuel exhaust gases contain poisonous carbon
monoxide. This gas is colorless and odorless, and can
cause death if inhaled.
NEVER tamper with the factory settings
of the engine or engine governor. Damage
to the engine or equipment can result
if operating in speed ranges above the
maximum allowable.
The engine of this equipment requires an adequate
free flow of cooling air. NEVER operate this equipment
in any enclosed or narrow
area where free flow of the
air is restricted. If the air
flow is restricted it will cause
injury to people and property
and serious damage to the
equipment or engine.
NEVER tip the engine to extreme angles during lifting as
it may cause oil to gravitate into the cylinder head, making
the engine start difficult.
PAGE 8 — MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INFORMATION
FUEL SAFETY
DANGER
BATTERY SAFETY (ELECTRIC START ONLY)
DANGER
DO NOT add fuel to equipment if it is placed inside truck
bed with plastic liner. Possibility exists of explosion or
fire due to static electricity.
DO NOT drop the battery.There is a possibility that the
battery will explode.
DO NOT expose the battery to open flames,
sparks, cigarettes, etc.The battery contains
combustible gases and liquids. If these
gases and liquids come into contact with a
flame or spark, an explosion could occur.
FUEL
WARNING
ALWAYS wear safety glasses when
handling the battery to avoid eye irritation.
The battery contains acids that can cause
injury to the eyes and skin.
FUEL
Use well-insulated gloves when picking up
the battery.
ALWAYS keep the battery charged. If the battery is not
charged, combustible gas will build up.
DO NOT start the engine near spilled fuel or combustible
fluids. Diesel fuel is extremely flammable and its vapors
can cause an explosion if ignited.
DO NOT charge battery if frozen. Battery can explode.
When frozen, warm the battery to at least 61°F (16°C).
ALWAYS refuel in a well-ventilated area, away from
sparks and open flames.
ALWAYS recharge the battery in a well-ventilated
environment to avoid the risk of a dangerous concentration
of combustible gases.
ALWAYS use extreme caution when working with
flammable liquids.
If the battery liquid (dilute sulfuric acid)
comes into contact with clothing or skin,
rinse skin or clothing immediately with
plenty of water.
DO NOT fill the fuel tank while the engine is running
or hot.
DO NOT overfill tank, since spilled fuel could ignite if it
comes into contact with hot engine parts or sparks from
the ignition system.
If the battery liquid (dilute sulfuric acid) comes into
contact with eyes, rinse eyes immediately with plenty
of water and contact the nearest doctor or hospital to
seek medical attention.
Store fuel in appropriate containers, in well-ventilated
areas and away from sparks and flames.
CAUTION
NEVER use fuel as a cleaning agent.
ALWAYS disconnect the NEGATIVE battery terminal
before performing service on the equipment.
DO NOT smoke around or near the
equipment. Fire or explosion could result
from fuel vapors or if fuel is spilled on a
hot engine.
ALWAYS keep battery cables in good working condition.
Repair or replace all worn cables.
MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14) — PAGE 9
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INFORMATION
TRANSPORTING SAFETY
CAUTION
NEVER allow any person or animal to stand underneath
the equipment while lifting.
NOTICE
Before lifting, make sure that the equipment parts (hook
and vibration insulator) are not damaged and screws are
not loose or missing.
Always make sure crane or lifitng device has been
properly secured to the lifting bail (hook) of the
equipment.
ALWAYS shutdown engine before transporting.
NEVER lift the equipment while the engine is running.
Tighten fuel tank cap securely and close fuel cock to
prevent fuel from spilling.
Use adequate lifting cable (wire or rope) of sufficient
strength.
Use one point suspension hook and lift straight
upwards.
DO NOT lift machine to unnecessary heights.
ALWAYS tie down equipment during transport by
securing the equipment with rope.
ENVIRONMENTAL SAFETY
NOTICE
Dispose of hazardous waste properly.
Examples of potentially hazardous waste
are used motor oil, fuel and fuel filters.
DO NOT use food or plastic containers to dispose of
hazardous waste.
DO NOT pour waste, oil or fuel directly onto the ground,
down a drain or into any water source.
PAGE 10 — MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
Table 1. MVH-306GH Reversible Plate
Compactor Specifications
Centrifugal Force
10,125 lb (4,602 kg)
4,400 vpm (70 Hz)
Vibration Frequency
Traveling Speed
0 to 75 ft/min (0 to 23 m/min)
Plate Size (L x W)
18 x 34 in (45.72 x 86.36 cm)
24 x 34 in (60.96 x 86.36 cm)
6,750 sq. ft. (2,057 sq. meters)
61.8 in (1570 mm)
With External Plate Size (L x W)
Max. Area of Compaction (no extensions)
Overall Length
Overall Width
18.0 in (457 mm)
Overall Height (with handle)
Overall Height (without handle)
Operating Weight D/DS
Operating Weight (with extension plates)
44.1 in (1120 mm)
31.7 in (805 mm)
673 lbs. ( 306 kg)
706 lbs. (321kg)
Table 2. Engine Specifications
Model
HONDA GX270K1SMX2
4-Stroke, Single Cylinder,
OHV, Gasoline Engine
Type
3.0 in. X 2.3 in.
(77 mm x 58 mm.)
Bore X Stroke
Displacement
16.5 cu-in (270 cm3)
9.0 H.P. (6.7 KW) @ 3600 R.P.M.
1.59 gallons (6.0 liters)
Unleaded Automobile Gasoline
1.16 quarts (1.1 liters)
Engine
Max Output
Fuel Tank Capacity
Fuel
Lube Oil Capacity
Speed Control Method
Starting Method
Centrifugal Fly-weight Type
Recoil Start
Dimension
(L x W x H)
14.0 x 16.9 X 16.1 in.
(355 X 430 X 410 mm.)
Dry Net Weight
55.1 lbs (25 Kg.)
MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14) — PAGE 11
Download from Www.Somanuals.com. All Manuals Search And Download.
DIMENSIONS
Figure 3. MVH306GH Reversible Plate Compactor Dimensions
Table 3. Dimensions
REF.
A
DIMENSIONS
53 in. (134.6 cm.)
B
18 in. (46 cm.)
34 in. (86 cm.)
63.8 in. (162 cm.)
31.7 (80.5 cm.)
C
D
E
PAGE 12 — MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL INFORMATION
Plate Compactor
Frequency/Speed
The Mikasa MVH306GH is a walk behind, reversible plate
compactor designed for the compaction of sand, clay and
asphalt. This plate compactor is a powerful compacting tool
capable of applying a tremendous force in consecutive high
frequency vibrations to a soil surface. Its applications include
soil compacting for road, embankments and reservoirs as well
as backfilling for gas pipelines, water pipelines and cable
installation work.
The compactor's vibrating plate maximum frequency is 4400
vpm (vibrations per minute).The forward and reverse travel speed
of the compactor is approximately 75 ft./minute (23 meters/
minute).
Engine
The Mikasa MVH306GH Plate Compactor is equipped with a
GX270K1-SMX2 (recoil start) gasoline engine.
Controls
Vibratory Plates
Before starting the MVH306GH Plate Compactor, identify and
understand the function of the controls and components as
indicated in Figure 4.
The vibratory plates of the MVH306GH produce low amplitude
high frequency vibrations, designed to compact granular soils.
The resulting vibrations cause forward motion.The engine and
handle are vibration isolated from the vibrating plate.The heavier
the plate, the more compaction force it generates.
ReversibleVibratory Plates
Reversible vibratory plates have two eccentric weights that allow
a smooth transition for forward and reverse travel, plus increased
compaction force as the result of dual weights.
Due to their weight and force, reversible plates are ideal for
semi-cohesive soils.
MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14) — PAGE 13
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPONENTS
Figure 4. MVH306GH R
Compactor Com
Figure 4 illustrates the location of the major components for the
MVH306GH Reversible Plate Compactor.The function of each
component is described below:
7. Belt Cover – Remove this cover to gain access to the V-
belts.NEVER run the compactor without theV-belt cover.If
the V-belt cover is not installed, the possibility exist that
your hand may get caught between the V-belt and clutch,
thus causing serious injury and bodily harm.
1. Hand Grip – When operating the compactor use this hand
grip to maneuver the compactor.
8. Base Plate – Designed to compact sand, clay, and asphalt.
2. Forward & Reverse Lever – Push the lever forward, the
compactor will move in a forward direction, pull the lever
backwards, the compactor will move in backwards direction.
Placing the lever in the middle (midway) will cause the
compactor not to move (neutral).
9. Oil Reservoir – Fill with Shell Tellus Oil 46 or equivalent
grade hydraulic oil.
10. Vibration Case – Encloses the eccentric, gears and
counter weights.
3. Handle Bar – When operating the compactor, this handle
is to be in the downward position. When the compactor is
to be stored, move the handle bar to the upright position.
11. Hydraulic Cylinder – Activated by moving the travel lever.
The cylinder controls the direction of movement by the plate
compactor.
4. Guard Hook - Used to lift the machine with crane or other
12. Shock Absorber – Protects plate compactor from damage
lifting device.
by absorbing vibration during operation.
5. Stopper - Locks the handle in place in the upward position
13. Throttle Lever – Controls speed of the plate compactor.
Place straight vertically to start, push fully counterclockwise
for full throttle and fully clockwise to stop plate compactor.
for stowing.
6. Engine – This plate compactor uses a GX270K1-SMX2
gasoline engine. Refer to the owner’s manual for engine
information and related topics.
14. Rubber Cover – Lift this rubber cover to gain access to
the fuel tank.
PAGE 14 — MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC ENGINE
Figure 5. Honda GX270 Engine Components
INITIAL SERVICING
The engine (Figure 5) must be checked for proper lubrication and
filled with fuel prior to operation. Refer to the manufacturers engine
manual for instructions & details of operation and servicing. The
engine shown above is a HONDA engine, operation for other
types of engines may vary somewhat.
6. Choke Lever – Used in the starting of a cold engine, or in
cold weather conditions. The choke enriches the fuel
mixture.
7. Air Cleaner – Prevents dirt and other debris from entering
the fuel system. Remove wing-nut on top of air filter
cannister to gain access to filter element.
1. Fuel Filler Cap – Remove this cap to add unleaded
gasoline to the fuel tank. Make sure cap is tightened
securely. DO NOT over fill.
NOTICE
WARNING
Operating the engine without an air filter, with a damaged air
filter, or a filter in need of replacement will allow dirt to enter
the engine, causing rapid engine wear.
DANGER
Add fuel to the tank only when the engine is
stopped and has cooled down. In the event
of a fuel spill, DO NOT attempt to start the
engine until the fuel residue has been
completely wiped up and the area
surrounding the engine is dry.
8. Spark Plug – Provides spark to the ignition system. Set
spark plug gap to 0.6 - 0.7 mm (0.028 - 0.031 inch) Clean
spark plug once a week.
9. Muffler – Used to reduce noise and emissions.
2. Throttle Lever – Used to adjust engine RPM speed (lever
advanced forward SLOW, lever back toward operator
FAST).
WARNING
Engine components can generate extreme
heat.To prevent burns, DO NOT touch these
areas while the engine is running or
immediatelyafteroperating. NEVERoperate
the engine with the muffler removed.
3. Engine ON/OFF Switch – ON position permits engine
starting, OFF position stops engine operations.
4. Recoil Starter (pull rope) – Manual-starting method. Pull
the starter grip until resistance is felt, then pull briskly and
smoothly.
10. Fuel Tank – Holds unleaded gasoline. For additional
5. FuelValve Lever – OPEN to let fuel flow, CLOSE to stop
information refer to engine owner's manual.
the flow of fuel.
MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14) — PAGE 15
Download from Www.Somanuals.com. All Manuals Search And Download.
INSPECTION
CAUTION
4. If the oil level is low (Figure 7), fill to the edge of the oil filler
hole with the recommended oil type (Table 4).Maximum oil
capacity is 1.16 quarts (1.10 liters).
NEVER operate the compactor in a
confined area or enclosed area structure
that does not provide ample free flow of
air.
CAUTION
ALWAYS wear approved eye and hearing
protection before operating the compactor.
Before Starting
Figure 7. Engine Oil Level
Table 4. Oil Type
1. Read safety instructions at the beginning
of manual.
2. Familiarize yourself with the operating
and control elements of the machine
Season
Summer
Spring/Fall
Winter
Temperature
25°C or Higher
25°C~10°C
Oil Type
SAE 10W-30
SAE 10W-30/20
SAE 10W-10
and the working environment. This includes obstacles in
the working area, bearing capacity of the ground and the
necessary safety provisions.
3. Check the air filter for dirt and dust. If air filter is dirty, replace
air filter with a new one as required.
0°C or Lower
4. Check fastening nuts and bolts for tightness. Loose threads
may cause damage to the machine when vibrating.
Checking the Hydraulic Oil Level
5. Understand the geographical features and regulations of
1. To check the engine oil level, place the compactor on secure
level ground with the engine stopped.
the job site.
6. Clean the compactor, removing dirt and dust.Particularly,
the bottom of the plate, engine cooling air inlet.
2. Remove the hydraulic oil breather cap located at the top of the
hydraulic oil tank (Figure 8).
3. Using a 24 mm wrench, remove the hydraulic oil filler plug.
Checking Engine Oil Level
3. Visually inspect to determine if hydraulic oil level is low. If oil
level is low add Shell Tellus 46 hydraulic oil or equivalent
through the hand pump oil filler port.
1. To check the engine oil level, place the compactor on secure
level ground with the engine stopped.
2. Remove the dipstick from the engine oil filler hole (Figure 6)
and wipe it clean.
3. Insert and remove the dipstick without screwing it into the
filler neck. Check the oil level shown on the dipstick.
Figure 8. Hydraulic Oil Filler Plug Removal
Figure 6. Engine Oil Dipstick Removal
PAGE 16 — MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
INSPECTION
CAUTION
DANGER
DO NOT overfill hydraulic oil tank. This could cause oil
leaks and sluggish operation. Clean cap and surrounding
area before opening to prevent dirt from entering oil tank.
EXPLOSIVE FUEL!
Motor fuels are highly flammable and can
be dangerous if mishandled. DO NOT
smoke while refueling. DO NOT attempt to
refuel if the engine is hot or running.
4. When adding hydraulic oil, only fill to the specified oil level as
marked on the front of the hydraulic oil tank (Figure 9). DO
NOT overfill.
Checking The Fuel
1. Remove the fuel cap located on top of fuel tank.
2. Visuallyinspecttoseeiffuellevelislow. Iffuelis low, replenish
with unleaded gasoline. (Figure 11).
3. Whenrefueling, besuretouseastrainerforfiltration. DONOT
top-off fuel. Wipe up any spilled fuel.
Figure 9. OilTank (Front View)
Checking the Air Cleaner
1. Loosen the wing nut and remove the air cleaner cover as
shown in Figure 10.
2. Remove the paper filter element and inspect it for signs of
wear or dirt. If paper filter element is dirty, clean or replace
element.
Figure 11. Refueling
Figure 10. Air Cleaner Element
MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14) — PAGE 17
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
CAUTION
DO NOT attempt to operate the
compactor until the Safety, General
Information and Inspection sections of this
manual have been read and
thoroughly understood.
This section is intended to assist the operator with the initial
start-up of the compactor. It is extremely important that this
section be read carefully before attempting to use the compactor
in the field.
Figure 13. Handle Adjustment
STARTING THE ENGINE
Refer to Figure 4 for the location of controls and components.
Starting the Engine (HONDA engine)
Releasing the Handle
1. Place the engine fuel valve lever (Figure 14) to the "ON"
1. Pull the handle release pin, (Figure 12) then push down on
the hand grip to release the handle.
position.
Figure 14. Engine Fuel Valve Lever (ON Position)
2. Move the throttle lever to the START position (Figure 15).
Figure 12. Handle Release Pin
Adjusting Handle Height
The height of the handle is adjustable for your comfort .
1. Loosen the butterfly screw (Figure 13).
2. Turn the grip clockwise to raise the handle or counterclock-
wise to lower the handle.
Figure 15. Throttle Lever (Start Position)
3. When the handle is raised to the desired height, tighten the
butterflyscrew.
PAGE 18 — MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
3. Place the choke lever (Figure 16) in the "OPEN " position
if starting a cold engine.
Figure 19. Starter Grip
7. If the engine has started, slowly return the choke lever
(Figure 17) to the CLOSED position. If the engine has not
started repeat steps 1 through 6.
8. Beforethecompactoris placedintooperation,runtheengine
for several minutes. Check for fuel leaks, and noises that
would be associated with a loose component.
Figure 16. Engine Choke Lever (Open)
4. Placethechoke lever(Figure17)in the"CLOSED"position
if starting a warm engine or the temperature is warm.
TRAVELING
1. Grasp the compactor's hand grip (Figure 20), and move the
engine throttle lever (Figure 20) quickly to the fast position.
2. With the throttle lever in the fast position, the engine speed
should be around 3,600 RPM, therefore engaging the cen-
trifugalclutch.
Figure 17. Engine Choke Lever (Closed)
5. Place the engine ON/OFF switch (Figure 18) in the "ON "
position.
Figure 20. Throttle Lever (Fast)
NOTICE
ALWAYS move the throttle lever quickly without hesitation,
because increasing the engine speed slowly causes the
clutch to slip.
Figure 18. Engine ON/OFF Switch (ON Position)
6. Grasp the starter grip (Figure 19) and slowly pull it out.The
resistancebecomesthehardestatacertainposition,corre-
spondingtothecompressionpoint.Pullthestartergripbriskly
andsmoothlyforstarting.
MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14) — PAGE 19
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
3. To make the compactor move in the forward direction push
the travel lever ( Figure 21) forward.
Figure 23. Engine ON/OFF Switch (OFF)
Figure 21. Travel Lever
4. Tomakethecompactormoveinthereversedirectionpullthe
travel lever ( Figure 21) backwards.
5. Firmly gasp the compactor's hand grip, the compactor will
beginmovinginthedesiredpositionwhenthedirectionlever
has been placed in the desired position.
6. Slowlywalkbehindthecompactorandbeonthelookout for
anylargeobjectsorforeignmatterthatmightcausedamage
to the compactor or bodily injury.
Figure 24. Fuel Valve Lever (OFF)
7. Iftravelleverisplacedintheneutralposition,themachinewill
vibrate in place.
Emergency Shutdown
1. Forarecoilstarttypeengine,movethethrottleleverquickly
8. Tomovethecompactorlaterally,holdthehandgripfirmlyand
swingcompactor. DONOTswingcompactorwhilegripping
the travel lever.
to the STOP position.
STOWING THE HANDLE
Normal Shutdown
1.
Push up the handle upward (Figure 25) until the handle locks
in place.
1.
Return the throttle lever to the START position (Figure 15).
Allow the machine to cool down for 2 to 3 minutes.
2. Place the travel lever in the NEUTRAL position.
3. Place the throttle lever in the STOP position (Figure 22) to stop
the engine.
4. Turn the engine ON/OFF switch to the“OFF”position (Figure 23).
5. Place the fuel shut-off lever (Figure 24) in the OFF
position.
Figure 25. Stowing the Handle
Figure 22. Throttle Lever (Stop)
PAGE 20 — MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Inspection and other services should always be carried out on
hard and level ground with the engine shut down.
NOTICE
Fuel piping and connections should be replaced every 2
years.
Inspection and Maintenance ServiceTables.
1. To make sure your plate compactor is always in good
working condition before using, carry out the maintenance
inspection in accordance withTables 5 through 7.
TABLE 6. MVH-306GH Engine Check
ITEM
HOURS OF OPERATION
Every 40 hours (every week)
Every 8 hours (every day)
Spark Plug Check
Oil or Fuel Leak
TABLE 5. MVH-306GH MACHINE INSPECTION
HOURS OF
OPERATION
ITEM
REMARKS
Tightness of Fastening
Threads
Every 8 hours (every day)
Loose or Missing
Screws
Every 8 hours
(every day)
Every 8 hours (every day)
(Replenish to specified maximum
level)
Engine Oil Check and
Replenishment
Every 8 hours
(every day)
Damaged Parts
Function of Controlling Every 8 hours
System Part (every day)
After first 25 hours then every 50 to
100 hours
Engine Oil Replacement
Air Filter Cleaning
Hydraulic System Leak Every 100 hours See page 21
Every 100 hours
Vibrator Oil Check
Every 100 hours See page 23
Every 300 hours See page 23
Every 100 hours See page 23
See separate engine manual for details on engine check.
Daily Service
Vibrator Oil
Replacement
Check for leakage of fuel or oil.
Hydraulic Oil Check
Check for loose screws including tightness. See Table 7
below (tightening torque ), for retightening:
First after 200
hours, then every See page 23
1,000 hours
Hydraulic Oil
Replacement
TABLE 7. TIGHTENING TORQUE
(in. kg/cm) Diameter
Material 6mm 8mm 10mm 12mm 14mm 16mm 18mm 20mm
V-belt (clutch) Check Every 200 hours See page 22
4T
70
150
250
400
300
500
800
500
750
1,100
2,000
2,900
1,400
2,000
Battery Check
Every 100 hours See page 24
6-8T
11T
100
150
800
1,300
2,000
2,700 3,800
4,200 5,600
1,200
NOTICE
300~ 650 ~
350 700
*
100
These inspection intervals are for operation under normal
conditions. Adjust your inspection intervals based on the
number hours plate compactor is in use, and particular
working conditions.
* (In case counter-part is of aluminum)
(Threads in use with this machine are all right handed)
Material and quality of material is marked on each bolt, and screw.
Remove soil and clean the bottom of compaction plate.
Check hand pump, piping and hose for any leakage. A
loosened hydraulic hose can be a cause for leakage. Check
hydraulic hose connections with wrench applied for
tightness.
Check engine oil.
MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14) — PAGE 21
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Air Filter
Spark Plug
1. Remove and clean the spark plug (Figure 26).
1. Remove the air cleaner cover and foam filter element as
shown in Figure 28.
2. Adjust the spark gap to 0.028 ~0.031 inch (0.6~0.7 mm).This
unit has electronic ignition, which requires no adjustments.
2. Tap the paper filter element (Figure 28) several times on a
hard surface to remove dirt, or blow compressed air [not
exceeding 30 psi (207 kPa, 2.1 kgf/cm2)] through the filter
elementfromtheaircleanercaseside.NEVER brushoffdirt.
Brushingwillforcedirtintothefibers.Replacethepaperfilter
element if it is excessively dirty.
3. Cleanfoamelementinwarm,soapywaterornonflammable
solvent. Rinseanddrythoroughly. Diptheelementinclean
engineoilandcompletelysqueezeouttheexcessoilfromthe
element before installing.
Figure 26. Spark Plug Gap
Engine Oil Replacement
1. Replace engine oil, first in 25 hours of operation and every
50 to 100 hours afterwards.
2. Drain the engine oil when the oil is warm as shown in
Figure 27.
3. Remove the oil drain bolt and sealing washer and allow
the oil to drain into a suitable container.
4. Replace engine oil with recommended type oil as listed
in Table 4. Engine oil capacity is 1.16 quarts (1.1 liters).
DO NOT overfill.
5. Install drain bolt with sealing washer and tighten se-
curely.
Figure 28. Engine Air Filter
CAUTION
NEVERattempttochecktheV-beltwiththeenginerunning.
Severeinjurycan occurifyourhandgetscaughtbetweenthe
V-belt and the clutch (Figure 29).Always use safety gloves.
CLUTCH
PULLEY
Figure 27. Engine Oil (Draining)
VIBRATOR
PULLEY
Figure 29. V-Belt Hazard
PAGE 22 — MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Vibrator Oil Level Check
NOTICE
Checking and Replacing the V-Belt and Clutch
1. After 200 hours of operation, remove the belt cover to check
the V-belt tension (Figure 30).Tension is proper if the belt
bends about 3/8”(10 mm) when depressed strongly with
finger between shafts.Loose or wornV-belts reduces power
transmission efficiency, causing weak compaction and
reduces the life of the belt itself.
Alwayscleantheareaaroundthevibratoroillevelcheckplug
before removing oil check plug. This will prevent dirt and
debrisfromenteringthesystem.
1. In every 100 hours of operation, with the machine positioned
horizontally, use a 3/4”(19 mm) wrench and remove vibrator
oil level check plug (Figure 31).Visually inspect and see if
vibrator oil level is up to filler port. Be sure to clean area
around check hole to prevent dirt and dust from entering.
Figure 30. V-Belt Check
Replacing the V-belt
Remove the belt cover. Engage an offset wrench 3/4”(19 mm) or
the like to vibrator pulley (lower) fastening bolt. Engage waste
cloth or the like at midway of V-belt on the left side and while
pulling it back strongly, rotate the offset wrench clockwise so that
theV-belt will come off.
Figure 31. Vibrator Oil Drain and Check Plugs
DrainingVibrator Oil
1. Replace vibrator oil after first 200 hours and in every 1,000
hours of operation.
Reinstalling the V-belt
EngageV-belt to lower vibrator pulley and push theV-belt to left
side of upper clutch and, in the same manner as in removal,
rotate offset wrench clockwise so that theV-belt goes back on.
2. Position handle bar vertically (storage position).
3. Using a 14 mm wrench remove the vibrator oil drain plug
(Figure 31) from the vibrating plate assembly.
Checking Clutch
Check the clutch simultaneously withV-belt checking. With belt
cover removed, check outer drum of the clutch for seizure and
"V" groove for wear or damage with your eyes. Clean the "V"
groove as necessary. Wear of lining or shoe should be checked
with running check. If the shoe is worn, power transmission
becomes deficient and slipping will result.
NOTICE
For draining oil through level check hole, have the machine
inclined with a sleeper or the like placed under the compaction
plate on opposite side.
4. After vibrator oil has been completely drained from machine,
fill with 10W-30 motor oil to the appropriate safe operating
level (Figure 31).
Replacing Clutch
RemoveV-belt.Remove bolt at engine power output by giving a
shock to an engaged wrench (tapping with hammer or the
like)and rotating bolt counterclockwise. Remove clutch with a
pulley extractor.To reinstall, reverse the procedure.
5. Reinstall drain plug into vibrating plate assembly.Apply seal
tape or Loctite #575 to thread portion of drain plug.
CAUTION
Draining Hydraulic Oil
Wheneverthecompactor'svibrationbecomesweakorlost
during normal operation regardless of operation hours,
check theV-belt and clutch immediately.
1. Disconnect the hydraulic hose connected to the hydraulic
oil cylinder (Figure 32).
MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14) — PAGE 23
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
CAUTION
Make sure hydraulic oil is at a normal safe operating level.
DO NOT over fill. Over filling (excessive oil) will cause
excess oil to blow out of breather plug.
3. Loosen bleeder plug located at top of hydraulic cylinder on
side of vibrator (Figure 35). Air remaining in the circuit will
be forced out of the bleeder plug. Once all air has been
purged from the hydraulic system, tighten bleeder plug
securely
Figure 32. Hydraulic Oil Cylinder
2. Push the travel lever back and forth to drain the hydraulic oil
from the hand pump (hydraulic oil reservoir).
4. Re-insert oil plug into hydraulic oil tank and tighten securely.
Re-install breather cap.
3. After draining hydraulic oil, reconnect hydraulic oil hose to
cylinder.
4. Place handle in upright position. Pull travel lever all the way
back (reverse), and using a rope, secure travel lever to hand
grip.
Adding Hydraulic Oil
1. Remove the breather cap and oil plug (Figure 33) from the
hydraulic oil tank using a 24mm hex socket.
Figure 35. Bleeder Plug
LONG TERM STORAGE
When storing your compactor for long periods do the following:
Run the engine at idle speed for 3-5 minutes.
Stop the engine. Drain the engine crankcase oil while the
engine is still warm. Fill engine crankcase with fresh oil.
Figure 33. Hydraulic OilTank
Wipe any oil or dirt that may have accumulated on the
compactor.
2. Using a funnel, add ShellTellus Oil #46 or equivalent to the
hydraulic oil tank through the oil filler port (Figure 34). Oil
tank capacity is 50.7 fl. oz (1500 cc)
Store compactor in a cool dry place out of reach of children
and unauthorized personnel.
.
Troubleshooting
See Tables 8 (engine) and 9 (plate compactor) on proceeding
pages for engine and plate compactor troubleshooting guide.
Figure 34. Hydraulic Oil Maintenance
PAGE 24 — MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
diagnosis based on the Engine Troubleshooting (Table 8)
information shown below.If the problem cannot be remedied,
please leave the unit just as it is and consult our company's
business office or service plant.
Practically all breakdowns can be prevented by proper
handling and maintenance inspections, but in the event of a
breakdown, please take a remedial action following the
TABLE 8. ENGINE TROUBLESHOOTING
SYMPTOM
POSSIBLE CAUSE
SOLUTION
Check gap, insulation or
replace spark plug.
Spark plug bridging?
Carbon deposit on spark plug?
Clean or replace spark plug.
Difficult to start, "fuel is available, but no
SPARK at spark plug".
Short circuit due to deficient spark plug
insulation?
Check spark plug insulation,
replace if worn.
Improper spark plug gap?
ON/OFF switch is shorted?
Ignition coil defective?
Set to proper gap.
Check switch wiring, replace
switch.
Replace ignition coil.
Set correct spark gap and
clean points.
Difficult to start, "fuel is available, and
SPARK is present at the spark plug".
Improper spark gap, points dirtry?
Condenser insulation worn or short
circuiting?
Replace condenser.
Replace defective spark plug
wiring.
Spark plug wire broken or short circuiting?
Wrong fuel type?
Flush fuel system, and replace
with correct type of fuel.
Difficult to start, "fuel is available, spark
is present and compression is normal"
Water or dust in fuel system?
Air cleaner dirty?
Flush fuel system.
Clean or replace air cleaner.
Re-seat valves.
Suction/exhaust valve stuck or protruded?
Replace piston rings and or
piston.
Piston ring and/or cylinder worn?
Difficult to start, "fuel is available, spark
is present and compression is low"
Cylinder head and/or spark plug not
tightened properly?
Torque cylinder head bolts and
spark plug.
Head gasket and/or spark plug gasket
damaged?
Replace head and spark plug
gaskets.
Fuel not available in fuel tank?
Fill with correct type of fuel.
Apply lubricant to loosen fuel
cock lever, replace if necessary.
Fuel cock does not open properly?
No fuel present at carburetor.
Fuel filter clogged?
Replace fuel filter.
Fuel tank cap breather hole clogged?
Air in fuel line?
Clean or replace fuel tank cap.
Bleed fuel line.
MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14) — PAGE 25
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
MVH306GH—TROUBLESHOOTING
TABLE 8. ENGINE TROUBLESHOOTING (CONTINUED)
SYMPTOM
POSSIBLE CAUSE
Air cleaner not clean?
SOLUTION
Clean or replace air cleaner
Check float adjustment, re-build
carbureator.
Improper level in carburetor?
"Weak in power" compression is proper
and does not misfire.
Defective Spark plug?
Defective Spark plug?
Clean or replace spark plug.
Flush fuel system, and replace
with correct type of fuel.
Water in fuel system?
"Weak in power" compression is proper
but misfires.
Dirty spark plug?
Clean or replace spark plug.
Replace ignition coil.
Ignition coil defective?
Replace with correct type of
spark plug.
Spark plug heat value improper?
Engine overheats.
Correct type of fuel?
Replace with correct type of fuel
Clean cooling fins.
Cooling fins dirty?
Governor adjusted correctly?
Governor spring defective?
Adjust governor.
Replace governor spring.
Rotational speed fluctuates.
Recoil starter malfunction.
Check entire fuel system for leaks
or clogs.
Fuel flow restricted?
Recoil mechanism clogged with dust and Clean recoil assembly with soap
dirt?
and water.
Sprial spring loose?
Replace sprial spring.
PAGE 26 — MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
MVH306GH—TROUBLESHOOTING
diagnosis based on the CompactorTroubleshooting (Table 9)
information shown below.If the problem cannot be remedied,
please leave the unit just as it is and consult our company's
business office or service plant.
Practically all breakdowns can be prevented by proper
handling and maintenance inspections, but in the event of a
breakdown, please take a remedial action following the
TABLE 9. TROUBLESHOOTING COMPACTOR
SYMPTOM
POSSIBLE CAUSE
SOLUTION
Adjust or replace clutch.
Clutch slips?
V-belt slips?
Adjust or replace V-belt.
Fill to correct level..
Excessive Oil in vibrator?
Check vibrator assembly for any worn or
defective parts, replace any defective
parts.
Travel speed low and vibration weak.
Trouble in vibrator internals?
Aeration in hydraulic oil for for travel
reversing syste.?
Purge air in hydraulic oil. (Bleed plug)
Engine speed incorrect?
Set engine speed to correct RPM.
Check entire travel system.
Clean installation of reversing lever.
Replace oil hose.
Travel reversing system inoperative.?
Reversing lever installation correct?
Broken or defective oil hose?
Aeration in hydraulic oil for for travel
reversing syste.?
Travels forward or backward but unable
to switch direction.
Purge air in hydraulic oil. (Bleed plug)
Excessive oil in reversing system?
Selector valve clogged with trash?
Fill to correct level..
Clean selector valve.
Check piston bearing in cylinder for
leakage at USH packing.
Cylinder piston bearing failure?
V-belt dis-engaged or slips?
Clutch slips?
Engage V-belt, adjust or replace.
Adjust clutch, replace if necessary.
Does not travel in forward or reverse.
Pump input shat key or adapter key-way
damaged?
Replace input shatkey or adapter key-way
Check piston bearing in cylinder for
leakage at USH packing.
Cylinder piston bearing failure?
Excessive hydraulic oil?
Reversing lever operating resistance
great.
Fill to correct level.
MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14) — PAGE 27
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLANATION OF CODE IN REMARKS COLUMN
The following section explains the different symbols and
QTY. Column
remarks used in the Parts section of this manual. Use the
help numbers found on the back page of the manual if there
are any questions.
Numbers Used — Item quantity can be indicated by a
number, a blank entry, or A/R.
A/R (As Required) is generally used for hoses or other
parts that are sold in bulk and cut to length.
NOTICE
The contents and part numbers listed in the parts
section are subject to change without notice.Multiquip
does not guarantee the availability of the parts listed.
A blank entry generally indicates that the item is not sold
separately.Other entries will be clarified in the“Remarks”
Column.
SAMPLE PARTS LIST
REMARKS Column
NO. PART NO. PART NAME
QTY. REMARKS
Some of the most common notes found in the “Remarks”
Column are listed below. Other additional notes needed
to describe the item can also be shown.
1
2%
12345
BOLT......................1 .....INCLUDES ITEMS W/%
WASHER, 1/4 IN............NOT SOLD SEPARATELY
WASHER, 3/8 IN....1 .....MQ-45T ONLY
2% 12347
3
4
12348
12349
HOSE ..................A/R ...MAKE LOCALLY
BEARING ..............1 .....S/N 2345B AND ABOVE
Assembly/Kit — All items on the parts list with the
same unique symbol will be included when this item is
purchased.
NO. Column
Indicated by:
Unique Symbols — All items with same unique
symbol
“INCLUDES ITEMS W/(unique symbol)”
(@, #, +, %, or >) in the number column belong to the
same assembly or kit, which is indicated by a note in the
“Remarks” column.
Serial Number Break — Used to list an effective serial
number range where a particular part is used.
Indicated by:
Duplicate Item Numbers — Duplicate numbers indicate
multiple part numbers, which are in effect for the same
general item, such as different size saw blade guards in
use or a part that has been updated on newer versions
of the same machine.
“S/N XXXXX AND BELOW”
“S/N XXXX AND ABOVE”
“S/N XXXX TO S/N XXX”
Specific Model Number Use — Indicates that the part
is used only with the specific model number or model
number variant listed. It can also be used to show a
part is NOT used on a specific model or model number
variant.
NOTICE
When ordering a part that has more than one item
number listed, check the remarks column for help in
determining the proper part to order.
Indicated by:
“XXXXX ONLY”
“NOT USED ON XXXX”
PART NO. Column
Numbers Used — Part numbers can be indicated by a
number, a blank entry, or TBD.
“Make/Obtain Locally” — Indicates that the part can
be purchased at any hardware shop or made out of
available items.Examples include battery cables, shims,
and certain washers and nuts.
TBD (To Be Determined) is generally used to show a
part that has not been assigned a formal part number
at the time of publication.
“Not Sold Separately”— Indicates that an item cannot
be purchased as a separate item and is either part of an
assembly/kit that can be purchased, or is not available
for sale through Multiquip.
A blank entry generally indicates that the item is not sold
separately or is not sold by Multiquip. Other entries will
be clarified in the “Remarks” Column.
PAGE 28 — MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
SUGGESTED SPARE PARTS
MVH-306WITH HONDA GX270K1SMX2 ENGINE
1 to 3 Units
Qty.... P/N ...................... Description
1 ....... 956100055 .......... THROTTLE WIRE
2 ....... 070200363 .......... V-BELT
3 ....... 9807955846......... SPARK PLUG
3 ....... 17210ZE2822 ...... ELEMENT, AIR CLEANER (DUAL)
1 ....... 17620Z0T814 ...... CAP, FUEL TANK
1 ....... 28462ZE2W11 ..... ROPE, RECOIL
MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14) — PAGE 29
Download from Www.Somanuals.com. All Manuals Search And Download.
NAMEPLATE AND DECALS
NAMEPLATE AND DECALS
5
Shell Tellus Oil
46
NPA-748
J
OPERATIONAL CAUTION
Do not move travel lever
if engine stops
6
8
NPA-1106
10
11
V BELT HDPF-5370
NPA-537
J
4
0PERATIONAL CAUTION
Prior to OPERATION, check the engine oil and fuel levels. If not enough, add to proper levels.
Warm up engine at low speed for 3-5 minutes.
Operate machine at full throttle speed. (incorrect clutch engagement causes clutch to burn.)
Use travel lever for forward & reverse motion. Do not push or pull travel lever strongly.
3
NPA-962
J
MVH-306
7
D
C
L333
Serial No.
Model No.
9
SAE 10W-30
MOTOR OIL
1
NPA-195
J
PAGE 30 — MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
NAMEPLATE AND DECALS
NAMEPLATE AND DECALS
NO.
1
3
4
5
6
7
8
9
PART NO.
920201950
920110370
920209620
920207480
920204580
920203330
920211060
PART NAME
DECAL: OIL SAE 10W-30........................... 1......... NPA-195
DECAL: MODEL LOGO
DECAL:CAUTION ...................................... 1......... NPA-962
DECAL: SHELL TELLUS OIL 46 ................ 1......... NPA-748
DECAL:FULLTHROTTLE .......................... 1......... NPA-458
DECAL: EAR PROTECTION ...................... 1......... DCL333
DECAL: CAUTION (TRAVEL LEVER) ........ 1......... NPA-1106
DECAL: SERIAL NO................................... 1......... CONTACT MQ PARTS DEPT.
QTY.
REMARKS
1
10
11
920201580
920211010
DECAL: MQ LOGO
DECAL:V-BELT HDPF-5370 ...................... 1......... NPA-537
1
MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14) — PAGE 31
Download from Www.Somanuals.com. All Manuals Search And Download.
VIBRATING PLATE ASSY.
VIBRATING PLATE ASSY.
PAGE 32 — MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
VIBRATING PLATE ASSY.
VIBRATING PLATE ASSY.
NO.
1
2
3
4
5
6
7
8
PART NO.
464117840
953405840
953402930
953400270
953405260
939010260
020316130
030216400
001221635
001221830
58407
030216400
939010010
020310080
031110160
030210250
464343730
011008015
030208200
52993
PART NAME
QTY.
1
1
1
1
1
4
4
4
4
8
8
4
4
4
4
4
REMARKS
VIBRATING PLATE
DRAIN PLUG MI8 (H)
COPPER PACKING 19X30X1
PLUG 1/4X14 10L
PACKING 1/4 (CU)
SHOCK ABSORBER 110X60H
NUT M16
WASHER, LOCK M16
BOLT 16X35 T
9
10
11
12
15
16
17
18
19
20
21
31
32
33
BOLT 18X30 T
WASHER, LOCK M18
WASHER, LOCK M16
SHOCK ABSORBER, STOPPER 45
NUT M10
WASHER, FLAT M10
WASHER, LOCK M10
COVER, VIBRATING PLATE
BOLT 8X15 T
2
8
8
2
8
8
WASHER, LOCK M8
EXTENSION PLATE
BOLT 18X50 T
012218050
58407
WASHER, LOCK M18
MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14) — PAGE 33
Download from Www.Somanuals.com. All Manuals Search And Download.
BASE AND ENGINE ASSY.
BASE AND ENGINE ASSY.
PAGE 34 — MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
BASE AND ENGINE ASSY.
BASE & ENGINE ASSY.
NO.
1
2
3
4
5
6
7
8
PART NO.
464117850
912227003
0105051045
030210250
031110160
464216580
001121025
030210250
031110160
464343670
464457360
456343340
951400110
952400690
001220830
030208200
464216640
092006010
464343660
464216590
001521050
464457430
464117920
456449950
011208030
030208200
031108160
022710809
PART NAME
QTY.
1
1
4
4
4
1
4
4
4
1
1
1
1
1
1
1
1
3
1
1
4
2
1
1
1
3
3
3
REMARKS
BASE
ENGINE ASSY., GX270K1SMX2 (HONDA)
BOLT 10X45 T
WASHER, LOCK M10
WASHER, FLAT M10
BELT COVER (IN)
BOLT 8X25 T
WASHER, LOCK M10
WASHER, FLAT M10
DUST-PROOF SPONGE (IN)
SPACER
CLUTCH ASSY./CHM03/W.FAN
KEY 7X7X35
9
10
11
12
13
14
15
16
17
18
19
20
21
26
35
36
37
38
39
40
WASHER 9X35X4.5
BOLT 8X30 T
WASHER, LOCK M8
DUST-PROOF COVER
FLAT HEAD SCREW 6X10
DUST-PROOF SPONGE (OUT)
BELT COVER (OUT)
SOCKET HEAD BOLT 10X50 T
SPACER, ENGINE
RUBBER COVER (GUARD FRAME)
PLATE, COVER
BOLT 8X30 T
WASHER, LOCK M8
WASHER, FLAT M8
NYLON NUT M8
MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14) — PAGE 35
Download from Www.Somanuals.com. All Manuals Search And Download.
MVH306GH — BASE AND ENGINE ASSY. (CONTINUED)
BASE AND ENGINE ASSY.
BASE AND ENGINE ASSY. (CONTINUED)
PAGE 36 — MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
BASE AND ENGINE ASSY.
MVH306GH — BASE AND ENGINE ASSY. (CONTINUED)
BASE AND ENGINE ASSY. (CONTINUED)
NO.
41
42
43
44
45
46
47
48
51
52
53
59
60
61
62
63
64
70
71
72
PART NO.
459010060
459010070
459010090
459010080
0401140030
464457380
014208020
030208200
464117900
012214030
030214350
90131ZE3790
9410912000
070200363
0830000010
151010680
58151
PART NAME
UNION TIP, DRAIN
DRAIN HOSE
HOSE BAND
GASKET(OIL DRAIN)
PLUG
DRAIN JOINT
BOLT 8X20 T
WASHER, LOCK M8
GUARD HOOK
BOLT 14X30 T
WASHER, LOCK M14
DRAIN JOINT
QTY.
1
1
2
2
1
1
1
1
1
4
4
1
1
1
1
1
REMARKS
WASHER, DRAIN PLUG M12
V-BELT
COIL SPRING
CLAMP CP.
WASHER, FLAT M5
CLIP D6 (FOR M10)
BOLT 10X15 T
1
1
1
1
959407260
001221015
030210250
WASHER, LOCK M10
MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14) — PAGE 37
Download from Www.Somanuals.com. All Manuals Search And Download.
VIBRATOR ASSY.
VIBRATOR ASSY.
PAGE 38 — MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
VIBRATOR ASSY.
VIBRATOR ASSY.
NO.
1#
2
3
4
5#
6#
8#
9#
PART NO.
464117880
001221470
001221450
030214350
047920120
457212410
951405370
456327150
080200550
060105030
951404970
464343700
009120301
456337670
009120302
456337380
456010010
464343720
040006911
953010030
042506000
080200100
455435051
455010070
080100260
456327130
456210636
050101050
0012221025
030210250
011008015
953404600
455010020
031110160
952405470
464343710
464457370
012212030
030212300
464216600
001520852
464910020
PART NAME
VIBRATING CASE
BOLT 14X150 T
QTY.
1
6
4
10
4
1
1
1
2
1
1
4
2
1
2
1
1
1
2
1
2
1
1
1
1
1
1
2
8
8
1
1
1
4
2
1
1
1
1
1
5
REMARKS
BOLT 14X50 T
WASHER, LOCK M14
ROLLER BEARING NJ310EMC4
ROTARY SHAFT, DRIVE
KEY 15X10X39 RR
GEAR, DRIVE
STOP RING S-55
OIL SEAL SB-50729
KEY 12X8X30 R
ECCENTRIC ROTATOR
SOCKET HEAD BOLT 16X40 T
ROTARY SHAFT, DRIVEN
SOCKET HEAD BOLT 16X30 T
PISTON ROD
KNOCK PIN 10X70
GEAR (DRIVEN)
10#
11#
12#
13#
14#
15#
16#
17#
18#
19#
20#
21#
25#
26#
27#
28#
29#
30#
31#
33#
34#
35#
36#
37#
38#
39#
43#
46#
47#
48#
49#
51
BEARING 6911
SEAL CAP/SC72-8N
BEARING 6000ZZSG
STOP RING S-10
PISTON, 22.4D
PACKING USH-22.4X30X5
STOP RING R-26
BEARING COVER
CYLINDER (L)/(AC)
O-RING G-105
BOLT 10X25 T
WASHER, LOCK M10
BOLT 8X12 T
COPPER PACKING 8X16X2
ELBOW 45 DEG. 15-0404
WASHER, FLAT M10
SHIM 90X110X0.5
PULLEY
WASHER
BOLT 12X30 T
WASHER, LOCK M12
BELT COVER (LOWER)
SOCKET HEAD BOLT 8X60 T
52
53
VIBRATOR ASSY ................................................1 ............. INCLUDES ITEMS W/#
MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14) — PAGE 39
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROL HANDLE ASSY.
CONTROL HANDLE ASSY.
PAGE 40 — MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROL HANDLE ASSY.
CONTROL HANDLE ASSY.
NO.
PART NO.
464343680
456336420
012212035
030212300
031112230
456336400
456449940
456449930
001221681
032124400
025306016
0401450160
020316130
020416100
455434950
455010030
939010060
020310080
020412070
022411635
954404230
011206020
030206150
952404470
020106050
501402870
501402880
959403460
020310080
456449980
953405260
031110160
464343690
0105050616
030206150
952404470
464457710
464457720
454010020
PART NAME
QTY.
1
1
4
4
4
2
2
2
1
2
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
6
6
6
1
1
1
REMARKS
1
2
3
4
5
7
8
9
HANDLE BRACKET
HANDLE BRACKET (R)
BOLT 12X35 T
WASHER, LOCK M12
WASHER, FLAT M12
RUBBER COUPLING
SHOCK ABSORBER
RUBBER PLATE
10
11
12
13
14
15
18
19
20
21
22
23
25
26
27
28
29
34
35
36
37
38
39
40
43
44
45
46
47
48
49
BOLT 16X250 T
CONICAL SPRING WASHER M24
SPRING PIN 6X16
WASHER, FLAT M16
NUT M16
NUT M16, H=10
SPINDLE
KNOB
SHOCK ABSORBER
NUT M10, H=6
NUT M12, H=7
WING NUT M16
CLAMP SA120-18
BOLT 6X20 T
WASHER, LOCK M6
WASHER, FLAT M6
NUT M6
HANDLE STOPPER
SPRING/HANDLE (1.4X18X44)
BALL GRIP 32D-M10
NUT M10, H=6
RUBBER PACKING 9D-20D-5T
PACKING 1/4 (CU)
WASHER, FLAT M10
HANDLE COVER
BOLT 6X15 T
WASHER, LOCK M6
WASHER, FLAT M6
PACKING A, HANDLE COVER
PACKING B, HANDLE COVER
CLAMPTC-100
MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14) — PAGE 41
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROL HANDLE ASSY.
CONTROL HANDLE ASSY.
PAGE 42 — MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROL HANDLE ASSY.
CONTROL HANDLE ASSY.
NO.
61
64
65
66
67
68
69
70
71
72
73
80
81
82
83
84
85
86
87
88
89
90
91
93
94
95
96
99
101
103
104
104
PART NO.
464117890
464216630
464457400
012010030
030210250
464216620
030210250
031110160
020310080
011208025
030208200
464457340
959403840
464457420
464457350
001520820
031116260
458460660
033910080
464457440
464010010
001220625
020306050
464010020
001520520
031105080
20305040
PART NAME
COLUMN, HANDLE
TRAVEL LEVER
HANDLE BOSS
BOLT 10X30 T
WASHER, LOCK M10
HANDLEW/RUBBER GRIP
WASHER, LOCK M10
WASHER, FLAT M10
NUT M10
BOLT 8X25 T
WASHER, LOCK
THROTTLE LEVER
BAR GRIP I.D. 12 MM
COVER,THROTTLE
ARM, THROTTLE
SOCKET HEAD BOLT 8X20 T
WASHER, FLAT
WASHER 16.4-35-0.6
CONICAL SW 16.3 X 31.5 X 1.2
STEEL BALL D6 (SUJ)
DRY BUSHING/ LBF-1620
BOLT 6X25 T
NUT M6
ROD END M5
SOCKET HEAD BOLT 5X20 T
WASHER, FLAT M5
NUT M5
OIL HOSE W/SPRING 1/4 X 920
THROTTLEWIRE
QTY.
1
1
1
2
2
1
2
2
2
2
2
1
1
1
1
1
1
2
3
1
1
2
2
1
1
1
1
1
1
1
1
1
REMARKS
954002270
956100055
454010020
959021815
959021810
CLAMPTC-100
SPRIAL TUBE 6D-330L
SPRIAL TUBE KEP6/ L=500
MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14) — PAGE 43
Download from Www.Somanuals.com. All Manuals Search And Download.
HAND PUMP ASSY.
HAND PUMP ASSY.
84
O-RING
SET
C
PAGE 44 — MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
HAND PUMP ASSY.
HAND PUMP ASSY.
NO.
PART NO.
4649-10040
464910080
464010040
464010050
464010060
464010070
099205005
464010080
464010090
464010100
458010080
001520620
050200200
050200220
050200180
464010110
464010111
050300400
050200150
050100400
069904010
069901010
984010030
984010040
984010050
464216721
PART NAME
QTY.
REMARKS
B
ACCUMLATOR
1
*
C
2
3
4
O-RING DUST,SEAL,SET ......................1 ............. INCLUDES ITEMS W/#
CONTROL SHAFT
BUSH
CAM
STOPPER
SOCKET HEAD SCREW 5X5 T
PLUG
PIN,STOPPER
PLUG
*
1
2
1
2
2
1
2
2
1
1
2
2
1
*
*
*
9
*
10
*
11
*
12
*
13
*
14
15
BREATHER
*
SOCKET HEAD BOLT 6X20 T
O-RING P-20
O-RING P-22
O-RING P-18
ACCUMULATOR CASE ..........................1 ............. S/N N2418 AND BELOW
ACCUMULATOR CASE ..........................1 ............. S/N N2419 AND ABOVE
O-RING S-40
O-RING P-15
O-RING G-40
DUST SEAL SER-40 ..............................1 ............. S/N N2419 AND ABOVE
DUST SEAL SER-15 ..............................1 ............. S/N N2419 AND ABOVE
SPRG.COMPRESSIONTOOL
DISASSEMBLING TOOL A
DISASSEMBLING TOOL B
*
16#
*
17#
19#
22
*
*
*
22
*
26#
27#
28#
48#
49#
81
1
1
1
*
*
*
*
*
1
1
1
82
83
84
HAND PUMP ASSY ...............................1 ............. INCLUDES ITEMS W/
*
MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14) — PAGE 45
Download from Www.Somanuals.com. All Manuals Search And Download.
GX270K1SMX2 — AIR CLEANER ASSY.
AIR CLEANER ASSY.
PAGE 46 — MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
GX270K1SMX2 — AIR CLEANER ASSY.
AIR CLEANER ASSY.
NO.
1
2
3
*
5
PART NO.
PART NAME
QTY.
REMARKS
16271ZE2010
17210ZE2822
17218ZE2821
17231ZH9820
17232891000
17238ZE2310
17239ZE1000
17410ZE2020
90325044000
90009ZE2003
9405006000
PACKING, ELBOW
1
ELEMENT,AIR CLEANER(DUAL) .............. 1 ...................... INCLUDES ITEM W/
FILTER, OUTER
COVER, AIR CLEANER
GROMET,AIR CLEANER
COLLAR,AIR CLEANER
COLLAR(B),AIR CLEANER
ELBOW COMP.,AIR CLEANER ................ 1 ...................... INCLUDES ITEM W/+
NUT
BOLT-WASHER 6X22
FLANGE NUT 6MM
NOSE, SILENCER
*
1
1
1
2
1
6
*
7+
8+
9
12
13
14
15
1
1
2
1
17235ZE2820
MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14) — PAGE 47
Download from Www.Somanuals.com. All Manuals Search And Download.
GX270K1SMX2 — CAMSHAFT ASSY.
CAMSHAFT ASSY.
PAGE 48 — MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
GX270K1SMX2 — CAMSHAFT ASSY.
CAMSHAFT ASSY.
NO.
1
2
3
4
PART NO.
PART NAME
QTY.
REMARKS
14100ZE3020
14410ZE2013
14431ZE2010
14441ZE2000
14451ZE1013
14568ZE1000
14711ZE2000
14721ZE2000
14751ZE2003
14771ZE2000
14773ZE2000
14781ZE2000
14791ZE2010
90012ZE0010
90206ZE1000
12209ZE8003
CAMSHAFT ASSY.................................... 1 ...................... INCLUDES ITEM W/
*
ROD,PUSH
ARM,VALVE ROCKER
LIFTER,VALVE
PIBOT,ROCKER ARM
SPRING,WEIGHT RETURN
VALVE, IN.
VALVE, EX.
SPRING,VALVE
RETAINER,IN.VALVE SPRING
RETAINER,EX.VALVE SPRING
ROTATOR,VALVE
PLATE,PUSH ROD GUIDE
PIBOT BOLT 8MM
2
2
2
2
1
1
1
2
1
1
1
1
2
2
1
5
6
*
7
8
9
10
11
12
13
14
15
16
NUT,PIBOT ADJUSTING
SEAL, VALVE STEM
MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14) — PAGE 49
Download from Www.Somanuals.com. All Manuals Search And Download.
GX270K1SMX2 — CARBURETOR ASSY.
CARBURETOR ASSY.
PAGE 50 — MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
GX270K1SMX2 — CARBURETOR ASSY.
CARBURETOR ASSY.
NO.
PART NO.
PART NAME
QTY.
REMARKS
1 %
16010ZE2812
16011ZA0931
16013ZA0931
16015ZE8005
16028ZE0005
16044ZE2005
16100ZH9W21
16124ZE0005
16166ZH9W20
16173001004
16211ZE2000
16220ZA0702
16221ZA0800
16223ZA0800
16610ZE1000
16953ZE1812
16954ZE1812
16956ZE1811
16957ZE1812
16967ZE0811
93500030061H
9430520122
GASKET SET
VALVE SET,FLOAT
FLOAT SET
1
1
1
*
2
3
*
*
5
8
CHAMBER SET,FLOAT ............................. 1 ...................... INCLUDES ITEM W/%
SCREW SET
CHOKE SET
CARBURETOR ASSY. (BE75B) ................ 1 ...................... INCLUDES ITEM W/
SCREW, THROTTLE STOP
NOZZLE, MAINE
*
1
1
*
9
10
*
*
11
1
1
1
1
1
1
1
*
13
*
14
*
PACKING,CUP
15
INSULATOR, CARBURETOR
SPACER COMP.,CARBURETOR
PACKING, CARBURETOR
PACKING, INSULATOR
CHOKE LEVER COMP.............................. 1 ...................... INCLUDES ITEM W/+
LEVER,COCK
PLATE,LEVER SETTING
SPRING,COCK LEVER
PACKING,FUEL COCK
CUP,FUEL STRAINER
SCREW 3X6
SPRING PIN 2X12
JET, MAIN, #80
JET SET,PILOT, #40
SCREW SET
DRAIN SCREW SET
COLLAR SET
16
17
18
19
20
1
1
1
1
1
2
1
1
1
1
1
1
21
*
23
*
24
*
25
*
26
27+
*
28
99101ZH80800
99204ZE20400
16016ZH7W01
*
29
*
30
*
31 % 16024ZE1811
*
32
16172ZE3W10
*
MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14) — PAGE 51
Download from Www.Somanuals.com. All Manuals Search And Download.
GX270K1SMX2 — CONTROL ASSY.
CONTROL ASSY.
PAGE 52 — MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
GX270K1SMX2 — CONTROL ASSY.
CONTROL ASSY.
NO.
1
2
3
4
PART NO.
PART NAME
ARM, GOVERNOR
ROD, GOVERNOR
QTY.
REMARKS
16551ZE2000
16555ZE2000
16561ZE2000
16562ZE2000
16570ZE2W10
16571ZE2W00
16574ZE1000
16575ZE2W00
16576891000
16578ZE1000
16581ZE2W00
16584883300
16592883310
16594883010
90013883000
90015ZE5010
90114SA0000
90605230000
93500040060H
93500050280A
93500050160A
9405006000
1
1
1
1
SPRING, GOVERNOR
SPRING,THROTTLE RETURN
CONTROL ASSY.(REMOTE)..................... 1 ...................... INCLUDES ITEM W/
LEVER, CONTROL
LEVER SPRING
WASHER,CONTROL LEVER
HOLDER,CABLE
SPACER,CONTROL LEVER
BASE COMP.,CONTROL
ADJUSTING SPRING
SPRING,CABLE RETURN
HOLDER, WIRE
FLANGE BOLT 6X12
BOLT, GOVERNOR ARM
LOCK NUT 6MM
6
*
10
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
*
11
*
12
*
13
*
15
*
16
*
17
*
19
*
20
*
24
25
27
*
28
*
CIR CLIP
SCREW 4X6
SCREW, PAN 5X28
SCREW 5X16
FLANGE NUT 6MM
30
*
32
*
33
*
35
MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14) — PAGE 53
Download from Www.Somanuals.com. All Manuals Search And Download.
GX270K1SMX2 — CRANKCASE COVER ASSY.
CRANKCASE COVER ASSY.
PAGE 54 — MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
GX270K1SMX2 — CRANKCASE COVER ASSY.
CRANKCASE COVER ASSY.
NO.
2
3
4
6
PART NO.
PART NAME
QTY.
REMARKS
11300ZH9S50
11381ZE2801
15600735003
15600ZG4003
15625ZE1003
16510ZE2000
COVER ASSY., CRANKCASE .................. 1 ...................... INCULDES ITEM W/
*
PACKINNG,CASE COVER
CAP ASSY.,OIL FILLER ........................... 1 ...................... INCLUDES ITEM W/%
OIL PLUG .................................................. 1 ...................... INCLUDES ITEM W/%
PACKING, OIL FILLER CAP
GOVERNOR ASSY.................................... 1 ...................... INCLUDES ITEM W/+
WEIGHT, GOVERNOR
HOLDER, GOVERNOR WEIGHT
PIN,GOVERNORWEIGHT
SLIDER, GOVERNOR
CLIP, GOVERNOR HOLDER
PIN,DOWEL 8X12
OIL SEAL, 30X46X8
PLAIN WASHER 6MM
FLANGE BOLT 8X35
1
8%
2
9
*
10 + 16511ZE2000
2
1
2
1
1
2
1
1
7
1
*
11 + 16512ZE2000
*
12 + 16513ZE2000
*
13
15
16
17
18
19
20
16531Z0A000
90602ZE1000
90701HC4000
91201890003
9410106800
957010803500
961006206000
*
*
*
*
BALL BEARING 6206
*
MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14) — PAGE 55
Download from Www.Somanuals.com. All Manuals Search And Download.
GX270K1SMX2 — CRANKSHAFT ASSY.
CRANKSHAFT ASSY.
PAGE 56 — MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
GX270K1SMX2 — CRANKSHAFT ASSY.
CRANKSHAFT ASSY.
NO.
1
9
11
12
PART NO.
PART NAME
QTY.
REMARKS
13310ZH9000
92101080250A
90534706010
951400110
CRANK SHAFT COMP. ............................. 1 ...................... INCULDES ITEM W/
*
BOLT 8X25
WASHER,LOCK 8MM
KEY 7X7X35
1
1
1
1
13
91001ZH9003
BEARING, BALL (6206 SH)
*
MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14) — PAGE 57
Download from Www.Somanuals.com. All Manuals Search And Download.
GX270K1SMX2 — CYLINDER BARREL ASSY.
CYLINDER BARREL ASSY.
PAGE 58 — MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
GX270K1SMX2 — CYLINDER BARREL ASSY.
CYLINDER BARREL ASSY.
NO.
1
2
3
6
PART NO.
PART NAME
QTY.
REMARKS
12000ZH9406
15510ZE2043
16541ZE2010
90131883000
90446KE1000
91201890003
91353671004
9405010000
9410912000
9425110000
957010601200
34150ZH7003
90013883000
90131ZE3790
9280012000
BARREL ASSY.,CYLINDER ...................... 1 ...................... INCULDES ITEM W/
*
SWITCH ASSY,OIL LEVEL
SHAFT,GOVERNOR ARM
BOLT,DRAIN PLUG
WASHER 8.2X17X0.8
OIL SEAL, 30X46X8
O-RING 14MM
FLANGE NUT M10
WASHER,DRAIN PLUG M12
PIN,LOCK 10MM
FLANGE BOLT 6X12
ALERT UNIT, OIL
FLANGE BOLT 6X12
DRAIN JOINT
1
1
2
1
1
1
1
2
1
2
1
1
1
1
7
9
10
*
11
12
13
14
16
17
19
20
BOLT, DRAIN PLUG 12MM
MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14) — PAGE 59
Download from Www.Somanuals.com. All Manuals Search And Download.
GX270K1SMX2 — CYLINDER HEAD ASSY.
CYLINDER HEAD ASSY.
PAGE 60 — MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
GX270K1SMX2 — CYLINDER HEAD ASSY.
CYLINDER HEAD ASSY.
NO.
PART NO.
PART NAME
QTY.
REMARKS
1
12200ZH9000
12204ZE2306
12205ZE2305
12216ZE2300
12251ZH9000
12310ZE2020
950051110030
12391ZE2020
14775ZE2010
90014ZE2000
90042ZE2000
92900080320E
90441ZE2010
9430112200
HEAD COMP.,CYLINDER ......................... 1 ...................... INCULDES ITEM W/
*
2
*
3
*
4
*
5
6
7
GUIDE,IN.VALVE(OVERSIZE)
GUIDE,EX.VALVE(OVERSIZE)
CLIP,VALVE GUIDE
GASKET, CYLINDER HEAD
COVER COMP.,HEAD
TUBE,11X100
PACKING,HEAD COVER
SEAT,VALVE SPRING
BOLT,HEAD COVER
BOLT,STUD 8X123
BOLT,STUD 8X32
WASHER COMP.,HEAD COVER
PIN,DOWEL 12X20
BOLT,FLANGE 10X80
PLUG, SPARK (BPR5ES)
1
1
1
1
1
1
1
1
1
2
2
1
2
4
1
8
9
11
12
13
14
15
16
17
957251008000
9807955846
MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14) — PAGE 61
Download from Www.Somanuals.com. All Manuals Search And Download.
GX270K1SMX2 — FAN COVER ASSY.
FAN COVER ASSY.
PAGE 62 — MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
GX270K1SMX2 — FAN COVER ASSY.
FAN COVER ASSY.
NO.
3
5
PART NO.
PART NAME
QTY.
REMARKS
16731ZE2003
19610ZE2010ZC
19631ZE2D00
36100ZH7003
90013883000
90013883000
90684ZA0601
CLIP,TUBE
1
1
1
1
5
1
1
COVER COMP.,FAN /BLACK
SHROUD
STOP SWITCH ASSY.
FLANGE BOLT 6X12
FLANGE BOLT 6X12
CLIP, HARNESS
7
11
17
18
22
MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14) — PAGE 63
Download from Www.Somanuals.com. All Manuals Search And Download.
GX270K1SMX2 — FLYWHEEL ASSY.
FLYWHEEL ASSY.
PAGE 64 — MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
GX270K1SMX2 — FLYWHEEL ASSY.
FLYWHEEL ASSY.
NO.
1
4
5
8
PART NO.
PART NAME
QTY.
REMARKS
19511ZE2000
28451ZE2W01
31100ZE2010
90201ZE3V00
90741ZE2000
FAN, COOLING
1
1
1
1
1
PULLEY, STARTER
FLYWHEEL COMP.
NUT,SPECIAL 16MM
KEY,SPECIALWOODRUFF25X18
9
MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14) — PAGE 65
Download from Www.Somanuals.com. All Manuals Search And Download.
GX270K1SMX2 — FUEL TANK ASSY.
FUEL TANK ASSY.
PAGE 66 — MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
GX270K1SMX2 — FUEL TANK ASSY.
FUEL TANK ASSY.
NO.
1
2
5
7
PART NO.
PART NAME
RUBBER,SUPPORT(107MM)
JOINT,FUELTANK
TANK COMP., FUEL NH1
CAP COMP., FUEL FILLER ...................... 1 ...................... INCLUDES ITEM W/
FUEL FILTER
O-RING 14MM
FLANGE NUT M8
TUBE, FUEEL 4.5X222
CLIP, TUBE
FLANGE BOLT 8X25
PAKING, FUEL FILLER CAP
QTY.
REMARKS
16854ZH8000
16955ZE1000
17510ZE2020ZD
17620Z0T814
17672ZE2W01
91353671004
9405008000
1
1
1
*
9
1
1
2
1
2
2
1
12
14
15
16
17
950014522240
9500202080
957010802500
17631Z0T812
22
*
MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14) — PAGE 67
Download from Www.Somanuals.com. All Manuals Search And Download.
GX270K1SMX2 — IGNITION COIL ASSY.
IGNITION COIL ASSY.
PAGE 68 — MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
GX270K1SMX2 — IGNITION COIL ASSY.
IGNITION COIL ASSY.
NO.
1
4
8
10
13
PART NO.
PART NAME
COIL AY,IGNITION/GX390
CAP ASSY.
GROMMET,CORD
CORD,STOP SWITCH 370MM
FLANGE BOLT 6X28
QTY.
REMARKS
30500-ZF6-W02
30700-ZE1-013
31512-ZE2-000
36101-ZE1-010
90015-883-000
1
1
1
1
1
MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14) — PAGE 69
Download from Www.Somanuals.com. All Manuals Search And Download.
GX270K1SMX2 — MUFFLER ASSY.
MUFFLER ASSY.
PAGE 70 — MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
GX270K1SMX2 — MUFFLER ASSY.
MUFFLER ASSY.
NO.
2
3
4
5
7
8
9
18
19
26
29
PART NO.
PART NAME
QTY.
REMARKS
18310ZE2W00
18320ZE2W01
18323ZE2W00
18330ZE2W00
18333ZE3800
18355ZE2010
18381ZE2W10
90013883000
90050ZE1000
9405008000
MUFFLER COMP.
1
1
1
1
1
1
1
1
6
3
1
PROTECTOR COMP.,MUFFLER
PROTECTOR, EXHAUST PIPE
PIPE,EXHAUST
GASKET
ARRESTER, SPARK
GASKET,MUFFLER(ARRESTER)
FLANGE BOLT 6X12
TAPPING SCREW 5X8
FLANGE NUT M8
90050ZE1000
TAPPING SCREW 5X8
MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14) — PAGE 71
Download from Www.Somanuals.com. All Manuals Search And Download.
GX270K1SMX2 — PISTON ASSY.
PISTON ASSY.
PAGE 72 — MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
GX270K1SMX2 — PISTON ASSY.
PISTON ASSY.
NO.
1
2
3
4
5
*
6
PART NO.
PART NAME
RING SET, PISTON (STD)
PISTON (STD)
QTY.
REMARKS
13010ZE8601
13101ZH9000
13111ZE2000
13200E2010
90001E8000
90551E1000
1
1
1
PIN ,PISTON
ROD ASSY., CONNECTING (STD) ........... 1 ...................... INCLUDES ITEM W/
BOLT, CONNECTING ROD
CLIP, PISTON PIN 18MM
*
2
2
MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14) — PAGE 73
Download from Www.Somanuals.com. All Manuals Search And Download.
GX270K1SMX2 — RECOIL STARTER ASSY.
GX270K1-SMX2 ENGINE — RECOIL STARTER ASSY.
RECOIL STARTER ASSY.
PAGE 74 — MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
GX270K1SMX2 — RECOIL STARTER ASSY.
GX270K1-SMX2 ENGINE — RECOIL STARTER ASSY.
RECOIL STARTER ASSY.
NO.
PART NO.
PART NAME
QTY.
REMARKS
1
28400ZE2W01ZB
28410ZE2W01ZB
28421ZE2W01
28422ZE2W01
28441ZE2W01
28442ZE2W01
28443ZE2W01
28444ZE2W01
28461ZE2W02
28462ZE2W11
90004ZE2W01
90008ZE2003
RECOIL STARTER AY/GX240,B............... 1 .....................INCLUDES ITEM W/
*
2
CASE COMP.,RECOIL STARTER
PULLEY,RECOIL STARTER
RATCHET,STARTER
SPRING,FRICTION
SPRING,STARTER RETURN
SPRING,RATCHET
RETAINER,SPRING
GRIP,STARTER
ROPE, RECOIL STARTER
SCREW,CENTER
BOLT,FLANGE 6X10
1
1
2
1
1
2
1
1
1
1
3
*
3
*
4
*
5
*
6
*
7
8
*
*
10
*
11
*
13
*
14
MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14) — PAGE 75
Download from Www.Somanuals.com. All Manuals Search And Download.
GX270K1SMX2 — LABELS ASSY.
LABELS ASSY.
PAGE 76 — MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
GX270K1SMX2 — LABELS ASSY.
LABELS ASSY.
NO.
3
7
10
17
PART NO.
PART NAME
QTY.
REMARKS
87521ZH9030
87522ZH9010
87528ZE2810
87532ZH8810
EMBLEM
1
1
1
1
RABEL /GX120K1
MARK,CHOKE(ORANGE)
LABEL
MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14) — PAGE 77
Download from Www.Somanuals.com. All Manuals Search And Download.
TERMS AND CONDITION OF SALE — PARTS
5. Parts must be in new and resalable
condition, in the original Multiquip
package (if any), and with Multiquip part
numbers clearly marked.
Multiquip reserves the right to quote and
sell direct to Government agencies, and to
Original Equipment Manufacturer accounts
who use our products as integral parts of their
own products.
PAYMENT TERMS
Terms of payment for parts are net 30 days.
FREIGHT POLICY
6. The following items are not returnable:
All parts orders will be shipped collect or
prepaid with the charges added to the invoice.
All shipments are F.O.B. point of origin.
Multiquip’s responsibility ceases when a
signed manifest has been obtained from the
carrier, and any claim for shortage or damage
must be settled between the consignee and
the carrier.
a. Obsolete parts. (If an item is in the
price book and shows as being
replaced by another item, it is
obsolete.)
SPECIAL EXPEDITING SERVICE
A $35.00 surcharge will be added to the
invoice for special handling including bus
shipments, insured parcel post or in cases
where Multiquip must personally deliver the
parts to the carrier.
b. Any parts with a limited shelf life
(such as gaskets, seals, “O” rings,
and other rubber parts) that were
purchased more than six months
prior to the return date.
LIMITATIONS OF SELLER’S LIABILITY
MINIMUM ORDER
Multiquip shall not be liable hereunder for
damages in excess of the purchase price of
the item with respect to which damages are
claimed, and in no event shall Multiquip be
liable for loss of profit or good will or for any
other special, consequential or incidental
damages.
The minimum charge for orders from Multiquip
is $15.00 net. Customers will be asked for
instructions regarding handling of orders not
meeting this requirement.
c. Any line item with an extended
dealer net price of less than
$5.00.
d. Special order items.
RETURNED GOODS POLICY
e. Electrical components.
f. Paint, chemicals, and lubricants.
g. Decals and paper products.
h. Items purchased in kits.
Return shipments will be accepted and
credit will be allowed, subject to the following
provisions:
LIMITATION OF WARRANTIES
No warranties, express or implied, are
made in connection with the sale of parts or
trade accessories nor as to any engine not
manufactured by Multiquip. Such warranties
made in connection with the sale of new,
complete units are made exclusively by a
statement of warranty packaged with such
units, and Multiquip neither assumes nor
authorizes any person to assume for it
any other obligation or liability whatever in
connection with the sale of its products. Apart
from such written statement of warranty,
there are no warranties, express, implied or
statutory, which extend beyond the description
of the products on the face hereof.
1. A Returned Material Authorization
must be approved by Multiquip prior to
shipment.
7. The sender will be notified of any material
received that is not acceptable.
8. Such material will be held for five
working days from notification, pending
instructions. If a reply is not received
within five days, the material will be
returned to the sender at his expense.
2. To obtain a Return Material Authorization,
a list must be provided to Multiquip
Parts Sales that defines item numbers,
quantities, and descriptions of the items
to be returned.
9. Credit on returned parts will be issued
at dealer net price at time of the original
purchase, less a 15% restocking
charge.
a. The parts numbers and descriptions
must match the current parts price
list.
b. The list must be typed or computer
generated.
10. In cases where an item is accepted, for
which the original purchase document
can not be determined, the price will be
based on the list price that was effective
twelve months prior to the RMA date.
c. The list must state the reason(s)
for the return.
Effective: February 22, 2006
d. The list must reference the sales
order(s) or invoice(s) under
which the items were originally
purchased.
11. Credit issued will be applied to future
purchases only.
PRICING AND REBATES
e. The list must include the name
and phone number of the person
requesting the RMA.
Prices are subject to change without prior
notice. Price changes are effective on a
specific date and all orders received on or
after that date will be billed at the revised price.
Rebates for price declines and added charges
for price increases will not be made for stock
on hand at the time of any price change.
3. AcopyoftheReturnMaterialAuthorization
must accompany the return shipment.
4. Freight is at the sender’s expense. All
parts must be returned freight prepaid to
Multiquip’s designated receiving point.
PAGE 78 — MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
NOTES
MVH306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #8 (01/31/14) — PAGE 79
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION AND PARTS MANUAL
HERE’S HOW TO GET HELP
PLEASE HAVE THE MODEL AND SERIAL
NUMBER ON-HAND WHEN CALLING
UNITED STATES
Multiquip Corporate Office
MQ Parts Department
18910 Wilmington Ave.
Carson, CA 90746
Contact: [email protected]
Tel. (800) 421-1244
Fax (310) 537-3927
800-427-1244
310-537-3700
Fax: 800-672-7877
Fax: 310-637-3284
Service Department
Warranty Department
800-421-1244
310-537-3700
Fax: 310-537-4259
Fax: 310-943-2238
800-421-1244
310-537-3700
Fax: 310-943-2249
Technical Assistance
800-478-1244
UNITED KINGDOM
CANADA
Multiquip
Multiquip (UK) Limited Head Office
4110 Industriel Boul.
Laval, Quebec, Canada H7L 6V3
Contact: [email protected]
Tel: (450) 625-2244
Tel: (877) 963-4411
Fax: (450) 625-8664
Unit 2, Northpoint Industrial Estate, Tel: 0161 339 2223
Fax: 0161 339 3226
Globe Lane,
Dukinfield, Cheshire SK16 4UJ
Contact: [email protected]
© COPYRIGHT 2014, MULTIQUIP INC.
Multiquip Inc, the MQ logo are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without written permission. All other trademarks are the property
of their respective owners and used with permission.
This manual MUST accompany the equipment at all times. This manual is considered a permanent part of the equipment and should remain with the unit if resold.
The information and specifications included in this publication were in effect at the time of approval for printing. Illustrations, descriptions, references and technical data contained in
this manual are for guidance only and may not be considered as binding. Multiquip Inc. reserves the right to discontinue or change specifications, design or the information published
in this publication at any time without notice and without incurring any obligations.
Your Local Dealer is:
Download from Www.Somanuals.com. All Manuals Search And Download.
|