OPERATION AND PARTS MANUAL
SERIES
MODEL MVH408GH
REVERSIBLE PLATE COMPACTOR
(HONDA GX390UT2SMXC GASOLINE ENGINE)
Revision #0 (03/25/2014)
To find the latest revision of this
publication, visit our website at:
THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.
Download from Www.Somanuals.com. All Manuals Search And Download.
PROPOSITION 65 WARNING
PAGE 2 — MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)— PAGE 3
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
Honda GX390UT2SMXC Engine
MVH408GH Reversible
Cylinder Head Assy........................................... 52-53
Cylinder Barrel Assy.......................................... 54-55
Crankcase Cover Assy...................................... 56-57
Crankshaft Assy................................................ 58-59
Piston Assy....................................................... 60-61
Camshaft Assy.................................................. 62-63
Recoil Starter Assy. .......................................... 64-65
Fan Cover Assy................................................. 66-67
Carburetor Assy................................................ 68-69
Air Cleaner Assy............................................... 70-71
Muffler Assy...................................................... 72-73
Fuel Tank Assy.................................................. 74-75
Flywheel Assy................................................... 76-77
Ignition Coil Assy............................................... 78-79
Control Assy...................................................... 80-81
Engine Decal Assy............................................ 82-83
Plate Compactor
Proposition 65 Warning ........................................... 2
Table Of Contents.................................................... 4
Parts Ordering Procedures...................................... 5
Safety Information .............................................. 6-10
Specifications ........................................................ 11
Dimensions............................................................ 12
General Information............................................... 13
Components ..................................................... 14-15
Basic Engine.......................................................... 16
Inspection ......................................................... 17-18
Startup.............................................................. 19-20
Operation.......................................................... 21-22
Maintenance..................................................... 23-29
Troubleshooting (Compactor) ................................ 30
Troubleshooting (Engine).................................. 31-32
Explanation Of Code In Remarks Column............. 34
Suggested Spare Parts ......................................... 35
Terms And Conditions Of Sale — Parts ................ 84
Compactor Component Drawings
Vibrating Plate Assy.......................................... 36-37
Vibrator Assy..................................................... 38-39
Base And Engine Assy...................................... 40-43
Electric Device Assy.......................................... 44-45
Control Assy...................................................... 46-49
Nameplate And Decals Assy............................. 50-51
NOTICE
Specifications and part numbers are subject to change
without notice.
PAGE 4 — MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS ORDERING PROCEDURES
Ordering parts has never been easier!
Choose from three easy options:
Effective:
January 1st, 2006
Best Deal!
Order via Internet (Dealers Only):
Order parts on-line using Multiquip’s SmartEquip website!
If you have an MQ Account, to obtain a Username
and Password, E-mail us at: parts@multiquip.
com.
View Parts Diagrams
Order Parts
Print Specification Information
To obtain an MQ Account, contact your
District Sales Manager for more information.
Use the internet and qualify for a 5% Discount
on Standard orders for all orders which include
complete part numbers.*
to log in and save!
Order Parts
Note: Discounts Are Subject To Change
Fax your order in and qualify for a 2% Discount
on Standard orders for all orders which include
complete part numbers.*
Order via Fax (Dealers Only):
All customers are welcome to order parts via Fax.
Domestic (US) Customers dial:
1-800-6-PARTS-7 (800-672-7877)
Note: Discounts Are Subject To Change
Domestic (US) Dealers Call:
Order via Phone:
1-800-427-1244
Non-Dealer Customers:
International Customers should contact
their local Multiquip Representatives for
Parts Ordering information.
Contact your local Multiquip Dealer for
parts or call 800-427-1244 for help in
locating a dealer near you.
When ordering parts, please supply:
Dealer Account Number
Specify Preferred Method of Shipment:
Dealer Name and Address
UPS/Fed Ex
DHL
Truck
Priority One
Ground
Shipping Address (if different than billing address)
Return Fax Number
Next Day
Second/Third Day
Applicable Model Number
Quantity, Part Number and Description of Each Part
NOTICE
All orders are treated as Standard Orders and will
ship the same day if received prior to 3PM PST.
WE ACCEPT ALL MAJOR CREDIT CARDS!
MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)— PAGE 5
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INFORMATION
Do not operate or service the equipment before reading
the entire manual. Safety precautions should be followed
at all times when operating this equipment.
Failure to read and understand the safety
messages and operating instructions could
result in injury to yourself and others.
Potential hazards associated with the operation of this
equipment will be referenced with hazard symbols which
may appear throughout this manual in conjunction with
safety messages.
SAFETY MESSAGES
The four safety messages shown below will inform you
about potential hazards that could injure you or others.The
safety messages specifically address the level of exposure
to the operator and are preceded by one of four words:
DANGER, WARNING, CAUTION or NOTICE.
SAFETY SYMBOLS
DANGER
Indicates a hazardous situation which, if not avoided,
WILL result in DEATH or SERIOUS INJURY.
WARNING
Indicates a hazardous situation which, if not avoided,
COULD result in DEATH or SERIOUS INJURY.
CAUTION
Indicates a hazardous situation which, if not avoided,
COULD result in MINOR or MODERATE INJURY.
NOTICE
Addresses practices not related to personal injury.
PAGE 6 — MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INFORMATION
GENERAL SAFETY
CAUTION
NOTICE
This equipment should only be operated by trained and
qualified personnel 18 years of age and older.
NEVER operate this equipment without proper protective
clothing, shatterproof glasses, respiratory protection,
hearing protection, steel-toed boots and other protective
devices required by the job or city and state regulations.
Whenever necessary, replace nameplate, operation and
safety decals when they become difficult read.
Manufacturer does not assume responsibility for any
accident due to equipment modifications. Unauthorized
equipment modification will void all warranties.
NEVER use accessories or attachments that are not
recommended by Multiquip for this equipment. Damage
to the equipment and/or injury to user may result.
NEVER operate this equipment when not
feeling well due to fatigue, illness or when
under medication.
ALWAYS know the location of the nearest
fire extinguisher.
NEVER operate this equipment under the influence of
drugs or alcohol.
ALWAYS know the location of the nearest
first aid kit.
ALWAYS know the location of the nearest phone or keep
a phone on the job site. Also, know the phone numbers
of the nearest ambulance, doctor and fire department.
This information will be invaluable in the case of an
emergency.
ALWAYS check the equipment for loosened threads or
bolts before starting.
DO NOT use the equipment for any purpose other than
its intended purposes or applications.
ALWAYS clear the work area of any debris, tools, etc.
that would constitute a hazard while the equipment is
in operation.
MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)— PAGE 7
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INFORMATION
COMPACTOR SAFETY
DANGER
WARNING
DO NOT place hands or fingers inside engine
compartment when engine is running.
NEVER operate the equipment in an explosive
atmosphere or near combustible materials.An
explosion or fire could result causing severe
bodily harm or even death.
NEVER operate the engine with heat shields or
guards removed.
Keep fingers, hands hair and clothing away
from all moving parts to prevent injury.
WARNING
NEVER disconnect any emergency or safety devices.
These devices are intended for operator safety.
Disconnection of these devices can cause severe injury,
bodily harm or even death.Disconnection of any of these
devices will void all warranties.
DO NOT remove the radiator cap while the
engine is hot. High pressure boiling water will gush out
of the radiator and severely scald any persons in the
general area of the compactor.
DO NOT remove the coolant drain plug
while the engine is hot. Hot coolant will
gush out of the coolant tank and severely
scald any persons in the general area of
the compactor.
CAUTION
NEVER lubricate components or attempt service on a
running machine.
NOTICE
DO NOT remove the engine oil drain plug while the
engine is hot. Hot oil will gush out of the oil tank and
severely scald any persons in the general area of the
compactor.
ALWAYS keep the machine in proper running condition.
Fix damage to machine and replace any broken parts
immediately.
CAUTION
ALWAYS store equipment properly when it is not being
used.Equipment should be stored in a clean, dry location
out of the reach of children and unauthorized personnel.
NEVER touch the hot exhaust manifold,
muffler or cylinder.Allow these parts to cool
before servicing equipment.
ENGINE SAFETY
DANGER
NOTICE
NEVER run engine without an air filter or with a dirty air
filter.Severe engine damage may occur.Service air filter
frequently to prevent engine malfunction.
The engine fuel exhaust gases contain poisonous carbon
monoxide. This gas is colorless and odorless, and can
cause death if inhaled.
NEVER tamper with the factory settings
of the engine or engine governor. Damage
to the engine or equipment can result
if operating in speed ranges above the
maximum allowable.
The engine of this equipment requires an adequate
free flow of cooling air. NEVER operate this equipment
in any enclosed or narrow
area where free flow of the
air is restricted. If the air
flow is restricted it will cause
NEVER tip the engine to extreme angles during lifting as
it may cause oil to gravitate into the cylinder head, making
the engine start difficult.
injury to people and property
and serious damage to the
equipment or engine.
PAGE 8 — MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INFORMATION
FUEL SAFETY
DANGER
BATTERY SAFETY (ELECTRIC START ONLY)
DANGER
DO NOT add fuel to equipment if it is placed inside truck
bed with plastic liner. Possibility exists of explosion or
fire due to static electricity.
DO NOT drop the battery. There is a possibility that the
battery will explode.
DO NOT expose the battery to open flames,
sparks, cigarettes, etc.The battery contains
combustible gases and liquids. If these
gases and liquids come into contact with a
flame or spark, an explosion could occur.
-306
H
V
M
WARNING
ALWAYS wear safety glasses when
handling the battery to avoid eye irritation.
The battery contains acids that can cause
injury to the eyes and skin.
MVH-306
Use well-insulated gloves when picking up
the battery.
ALWAYS keep the battery charged. If the battery is not
charged, combustible gas will build up.
DO NOT start the engine near spilled fuel or combustible
fluids. Diesel fuel is extremely flammable and its vapors
can cause an explosion if ignited.
DO NOT charge battery if frozen. Battery can explode.
When frozen, warm the battery to at least 61°F (16°C).
ALWAYS refuel in a well-ventilated area, away from
sparks and open flames.
ALWAYS recharge the battery in a well-ventilated
environmenttoavoidtheriskofadangerousconcentration
of combustible gases.
ALWAYS use extreme caution when working with
flammable liquids.
If the battery liquid (dilute sulfuric acid)
comes into contact with clothing or skin,
rinse skin or clothing immediately with
plenty of water.
DO NOT fill the fuel tank while the engine is running
or hot.
DO NOT overfill tank, since spilled fuel could ignite if it
comes into contact with hot engine parts or sparks from
the ignition system.
If the battery liquid (dilute sulfuric acid) comes into
contact with eyes, rinse eyes immediately with plenty
of water and contact the nearest doctor or hospital to
seek medical attention.
Store fuel in appropriate containers, in well-ventilated
areas and away from sparks and flames.
CAUTION
NEVER use fuel as a cleaning agent.
ALWAYS disconnect the NEGATIVE battery terminal
before performing service on the equipment.
DO NOT smoke around or near the
equipment. Fire or explosion could result
from fuel vapors or if fuel is spilled on a
hot engine.
ALWAYS keep battery cables in good working condition.
Repair or replace all worn cables.
MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)— PAGE 9
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INFORMATION
When the life cycle of this equipment is over, remove
battery and bring to appropriate facility for lead
reclamation. Use safety precautions when handling
batteries that contain sulfuric acid.
TRANSPORTING SAFETY
CAUTION
NEVER allow any person or animal to stand underneath
the equipment while lifting.
When the life cycle of this equipment is over, it is
recommended that the trowel frame and all other metal
parts be sent to a recycling center.
NOTICE
Metal recycling involves the collection of metal from
discarded products and its transformation into raw
materials to use in manufacturing a new product.
Before lifting, make sure that the equipment parts (hook
and vibration insulator) are not damaged and screws are
not loose or missing.
Recyclers and manufacturers alike promote the process
of recycling metal. Using a metal recycling center
promotes energy cost savings.
Always make sure crane or lifitng device has been
properly secured to the lifting bail (hook) of the
equipment.
EMISSIONS INFORMATION
ALWAYS shutdown engine before transporting.
NOTICE
NEVER lift the equipment while the engine is running.
The diesel engine used in this equipment has been
designed to reduce harmful levels of carbon monoxide
(CO), hydrocarbons (HC) and nitrogen oxides (NOx)
contained in diesel exhaust emissions.
Tighten fuel tank cap securely and close fuel cock to
prevent fuel from spilling.
Use adequate lifting cable (wire or rope) of sufficient
strength.
This engine has been certified to meet US EPA Evaporative
emissions requirements in the installed configuration.
Use one point suspension hook and lift straight
upwards.
Attempting to modify or make adjustments to the engine
emission system by unauthorized personnel without proper
training could damage the equipment or create an unsafe
condition.
DO NOT lift machine to unnecessary heights.
ALWAYS tie down equipment during transport by
securing the equipment with rope.
Additionally, modifying the fuel system may adversely affect
evaporative emissions, resulting in fines or other penalties.
ENVIRONMENTAL SAFETY/DECOMMISSIONING
NOTICE
Emission Control Label
Decommissioning is a controlled process used to safely
retire a piece of equipment that is no longer serviceable.
If the equipment poses an unacceptable and unrepairable
safety risk due to wear or damage or is no longer cost
effective to maintain (beyond life-cycle reliability) and is to
be decommissioned (demolition and dismantlement),be
sure to follow rules below:
The emission control label is an integral part of the emission
system and is strictly controlled by regulations.
The label must remain with the engine for its entire life.
If a replacement emission label is needed, please contact
your authorized Kohler Engine Distributor.
DO NOT pour waste or oil directly onto the ground, down
a drain or into any water source.
Contact your country's Department of
Public Works or recycling agency in your
area and arrange for proper disposal of
any electrical components, waste or oil
associated with this equipment.
PAGE 10 — MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
Table 1. MVH408GH Specifications
Centrifugal Force 12,365 lbf (55 kN)
Vibration Frequency
Maximum Traveling Speed
Plate Size (W x L)
4,400 vpm (73 Hz)
82 ft/min (25 m/min)
19.68 x 35.3 in (500 x 900 mm)
25.6 x 35.3 in (650 x 900 mm)
82 ft./min (25 m/min)
Plate Size (W x L) with extension plates
Max. Forward Speed
Operating Weight
802 lbs. (364 kg.)
Operating Weight with extension plates
836 lbs. (379 kg.)
Table 2. Engine Specifications
Engine Make
Engine Model
HONDA
GX390UT2SMXC
Engine Type
Air-cooled, 4 stroke Gasoline Engine
3.46 in. x 2.52 in. (88 mm x 64 mm)
23.74 cu-in (389 cc)
Cylinder Bore X Stroke
Displacement
Maximum Ouput
Fuel Tank Capacity
Fuel Type
11.7 BHP (8.7 kW) @ 3600 RPM
Approx. 1.4 U.S. gallons (6.1 liters)
Unleaded 86 Octane or Higher
1.16 qts (1.1 liters)
Oil Capacity
Starting Method
Recoil Start
Dry Net Weight Recoil/Electric
Dimensions (L x W x H)
69.89 lbs (31.7 Kg.)
15.98 x 18.11 x 17.64 in (406 x 460 x 448 mm)
MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)— PAGE 11
Download from Www.Somanuals.com. All Manuals Search And Download.
DIMENSIONS
Stored position
D
E
Working position
C
F
A
G
B
extension plate (option)
Figure 1. Dimensions
Table 3. Dimensions
REF. DES
IN. (MM)
19.68 (500)
25.60 (650)
36.61 (930)
47.64 (1210)
53.54 (1360)
35.3 (900)
A
B
C
D
E
F
G
62.01 (1575)
PAGE 12 — MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL INFORMATION
DEFINITION OF PLATE COMPACTOR
FREQUENCY/SPEED
The Mikasa MVH408GH is a reversible plate compactor
designed for efficient compaction of sand, graveland
cohesive soils. This plate compactor is a powerful
compacting tool capable of applying a tremendous force
in consecutive high frequency vibrations to a soil surface.
Its applications include compacting for road, embankments
and reservoirs as well as backfilling for gas pipelines, water
pipelines and cable installation work.
The compactor's vibrating plate produces a vibration
frequency of 4,400 VPM (vibrations per minute).
The travel speed of the compactor is approximately
82 ft/minute (25 meters/minute).
ENGINE
This plate compactor is equipped with a Honda
GX390UT2SMXC air cooled, 4-cycle gasoline engine.
The engine drives an eccentric weight at a high speed to
develop a compaction force.
VIBRATORY PLATES
The vibratory plates of the compactor produce low
amplitude high frequency vibrations, designed to compact
granular soils and asphalt.
CONTROLS
Before starting the plate compactor identify and understand
the function of all the controls and components.
The resulting vibrations cause forward motion.The engine
and handle are vibration isolated from the vibrating plate.
MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)— PAGE 13
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPONENTS
1
2
4
3
5
8
6
7
10
17
12
Neutral
Forward
Reverse
9
11
(Stored position
13
11
(Working position)
16
15
14
Figure 2. Plate Compactor Components
PAGE 14 — MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPONENTS
Figure 2 shows the location of the basic controls and
components of the MVH408GH Plate Compactor. The
function of each control is described below:
cast iron construction used in the compacting of soil.
10. Extension Plate — Provides additional area of
vibration to the vibrating plate.
1. Rubber Cover — Lift this rubber cover to gain access
to the fuel tank.
11. Handle Bar — When operating the compactor, this
handle is to be in the downward position. When the
compactor is to be stored, move the handle bar to
the upright position.
2. Hour/Tachometer — Displays the cumulative time
that the machine has been in use. During operation it
displays the rpm reading.
12. Direction Control Lever — Push the lever forward to
move compactor in a forward direction. Pull the lever
backwards to move compactor in backwards direction.
Placing the lever in the middle (midway) will cause the
compactor not to move (neutral).
3. Handle Bar Height Adjuster — Adjusts the the handle
bar to the desired height by loosening the wing nut and
turning the grip clockwise to raise the handle bar and
counterclockwise to lower the handle bar.
4. Breather Plug — Allow pressure to escape to the air
in the form of a gas from heat.
13. Throttle Lever — Controls speed of the plate
compactor. Place straight vertically to start, push fully
counterclockwise for full throttle and fully clockwise to
stop plate compactor.
5. Hydraulic Pump (Oil Reservoir) — Regulates
hydraulic oil flow produced by the direction of the
control lever.
14. Vibrator Oil Drain Plug — Used to drain vibrator oil
from the machine.
6. Hand Grip — When operating the compactor use this
hand grip to maneuver the compactor.
15. Vibration Case Oil Filler — Used to add oil to the
vibration case.
7. Cyclone Cleaner — Filters large dust particles to keep
air cleaner from getting clogged easily.
16. Engine—ThisplatecompactorusesaGX390UT2SMXC
gasoline engine. Refer to the owner’s manual for
engine information.
8. Lifting Bale — When lifting of the compactor is
required either by forklift, crane etc., tie rope or chain
around this lifting point.
17. Engine ON-OFF Switch — Used to turn the engine
on or off.
9. Vibrating Plate — A flat, open plate made of durable
MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)— PAGE 15
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC ENGINE
1
9
8
2
7
12
6
5
11
10
4
3
Figure 3. Engine Controls and Components
INITIAL SERVICING
6. Air Cleaner – Prevents dirt and other debris from
entering the fuel system. Remove wing-nut on top of
air filter canister to gain access to filter element.
The engine (Figure 3) must be checked for proper
lubrication and filled with fuel prior to operation.Refer to the
manufacturer's engine manual for instructions and details
of operation and servicing.
NOTICE
1. Fuel Filler Cap – Remove this cap to add unleaded
gasoline to the fuel tank. Make sure cap is tightened
securely. DO NOT over fill.
Operating the engine without an air filter, with a
damaged air filter, or a filter in need of replacement
will allow dirt to enter the engine, causing rapid engine
wear.
DANGER
Add fuel to the tank only when the engine
is stopped and has had an opportunity to
cool down. In the event of a fuel spill, DO
NOT attempt to start the engine until the
fuel residue has been completely wiped up
and the area surrounding the engine is dry.
7. Spark Plug – Provides spark to the ignition system.
Set spark plug gap according to engine manufacturer's
instructions. Clean spark plug once a week.
8. Muffler – Used to reduce noise and emissions.NEVER
touch when hot!
9. Fuel Tank – Fill with unleaded gasoline. Reference
Table 2 for fuel tank capacity.For additional information
refer to Honda engine owner's manual.
2. Throttle Lever – Used to adjust engine RPM speed.
For normal operation this lever should always be placed
in the RUN position.
10. Dipstick/Oil Filler Cap – Remove this cap to determine
if the engine oil is low. Add oil through this filler port as
recommended in (Table 4).
3. Recoil Starter (Pull Rope) – Manual-starting method.
Pull the starter grip until resistance is felt, then pull
briskly and smoothly.
11. Oil Drain Plug – Remove this plug to remove oil from
the engine's crankcase.
4. Fuel Valve Lever – OPEN to let fuel flow, CLOSE to
stop the flow of fuel.
12. Engine ON/OFF Switch – ON position permits engine
starting, OFF position stops engine operation.
5. Choke Lever – Used in the starting of a cold engine,
or in cold weather conditions. The choke enriches the
fuel mixture.
PAGE 16 — MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
INSPECTION
BEFORE STARTING
DANGER
EXPLOSIVE FUEL!
1. Read all safety instructions at the beginning of manual.
2. Clean the compactor, removing dirt and dust,
particularly the engine cooling air inlet, carburetor and
air cleaner.
Motor fuels are highly flammable and can
be dangerous if mishandled. DO NOT
smoke while refueling. DO NOT attempt
to refuel the compactor if the engine is
hot! or running.
3. Check the air filter for dirt and dust. If air filter is dirty,
replace air filter with a new one as required.
4. Check carburetor for external dirt and dust. Clean with
dry compressed air.
FUEL CHECK
1. Visually inspect (Figure 6) to see if fuel level is low. If
fuel is low, replenish with unleaded fuel.
5. Check fastening nuts and bolts for tightness.
ENGINE OIL CHECK
FUEL
CAP
1. To check the engine oil level, place the compactor on
secure level ground with the engine stopped.
2. Remove the dipstick from the engine oil filler hole
(Figure 4) and wipe clean.
Figure 6. Fuel Check
Figure 4. Engine Oil Dipstick Removal
2. When refueling, be sure to use a strainer for filtration.
DO NOT top-off fuel. Wipe up any spilled fuel
immediately.
3. Insert and remove the dipstick without screwing it into
the filler neck.Check the oil level shown on the dipstick.
4. If the oil level is low (Figure 5), fill to the edge of the
oil filler hole with the recommended oil type as listed
in Table 4. Refer to Table 2 for maximum engine oil
capacity.
V-BELT COVER REMOVAL
To inspect the V-belt, remove the three bolts that secure
the belt cover to the frame as shown in Figure 7.
REMOVE
VIBRATOR
REMOVE
V-BELT
Figure 5. Engine Oil Dipstick (Oil Level)
Mikasa
Table 4. Oil Type
Season
Summer
Spring/Fall
Winter
Temperature
25°C or Higher
25°C~10°C
Oil Type
SAE 10W-30
SAE 10W-30/20
SAE 10W-10
V-BELT COVER
Figure 7. V-Belt Cover Removal
0°C or Lower
MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)— PAGE 17
Download from Www.Somanuals.com. All Manuals Search And Download.
INSPECTION
V-BELT INSPECTION
VIBRATOR OIL CHECK
Visually examine the V-belt (Figure 8) and determine if it
is full of tiny cracks, frayed, has pieces of rubber missing,
is peeling or otherwise damaged.
1. Place the plate compactor horizontally on a flat surface.
Make sure the compactor is level when checking the
oil in the vibrator assembly.
Also, examine the belt and determine if it is oil soaked or
"glazed " (hard shiny appearance on the sides of the belt).
Either of these two conditions can cause the belt to run hot,
which can weaken it and increase the danger of it breaking.
2. Check vibrator oil level by removing the oil plug (vibrator
oil gauge) as shown in Figure 10. Clean the oil gauge
and re-thread back in.Remove the oil gauge again and
confirm oil level does not exceed the cross hash of the
oil plug. DO NOT OVERFILL
If the V-belt exhibits any of the referenced wear conditions
replace the V-belt immediately
OIL SOAKED
3. The vibrator holds approximately 20.3 oz. (600 cc).
IMPORTANT, if oil is required, replace using only SAE
10W-30 motor oil.
Oil gauge
(19mm wrench)
Effective
CORD FAILURE
GLAZED
WORN BACK
COVER
BROKEN
MISSING RUBBER
Drain plug
CRACKS
(14mm wrench)
SIDEWALL
WEAR
Figure 8. Drive Belt Inspection
Figure 10. Vibrator Oil Check
V-BELT TENSION
HANDLE BAR
TheV-belt tension is proper if theV-belt bends 10 to 15 mm
(Figure 9) when depressed with finger at midway between
the clutch and vibrator pulleys.
The height of the handle bar can be adjusted for ease of
use.Adjust the handle height as follows.Refer to Figure 11.
1. Loosen the wing nut.
CORRECT V-BELT
2. Turn the grip clockwise to raise the handle or
counterclockwise to lower the handle.
TENSION 10-15 MM
CLUTCH
WHEN DEPRESSED
PULLEY
AS SHOWN.
3. When the handle bar is raised to the desired height,
tighten the wing nut.
Grip
V-BELT
VIBRATOR
PULLEY
Wing nut
Figure 9. V-Belt Tension
Figure 11. Handle Height Adjustment
PAGE 18 — MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
STARTUP
3. Place the choke lever (Figure 14) in the “CLOSED”
position if starting a cold engine.
CAUTION
DO NOT attempt to operate the compactor
until the Safety, General Information and
Inspection sections of this manual have
been read and thoroughly understood.
CHOKE LEVER
This section is intended to assist the operator with the
initial startup of the compactor. It is extremely important
that this section be read carefully before attempting to use
the compactor in the field.
STARTING THE ENGINE
CLOSED
1. Place the engine fuel valve lever (Figure 12) to the
“ON” position.
Figure 14. Choke Lever (Closed)
NOTICE
The CLOSED position of the choke lever enriches the
fuel mixture for starting a COLD engine. The OPEN
position provides the correct fuel mixture for normal
operation after starting, and for restarting a warm
engine.
4. When the engine is stopped, the hour tachometer
always shows "cumulative time" (Figure 15).
Figure 12. Engine FuelValve Lever (ON Position)
DIESEL ENGINE TACH &HOUR METER
2. Move the throttle lever (Figure 13) slightly higher from
the idle position.
HRS
Throttle lever
Figure 15. Hour Tachometer (Cumulative Time)
5. Place the engine ON/OFF switch (Figure 16) in the
"ON" position.
Slightly higher
Handle
position
Idle position
Figure 13. Throttle Lever (Higher Position)
Figure 16. Engine ON/OFF Switch (ON Position)
MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)— PAGE 19
Download from Www.Somanuals.com. All Manuals Search And Download.
STARTUP
6. Grasp the starter grip (Figure 17) and slowly pull it
out. The resistance becomes the hardest at a certain
position, corresponding the compression point.Rewind
the rope a little from that point and pull out sharply.
9. Before the compactor is placed in to operation, run the
engine for several minutes. Check for fuel leaks, and
noises that would associate with a loose component.
10. During operation, the hour tachometer displays
"rotation number" (Figure 19).
Cumulative time
Rotation number
DIESEL ENGINE TACH &HOUR METER
DIESEL ENGINE TACH &HOUR METER
HRS
RPM
Figure 19. Hour Tachometer (Rotation Number)
Figure 17. Starter Grip
NOTICE
DO NOT pull the starter rope all the way to the end
DO NOT release the starter rope after pulling. Allow it
to rewind as soon as possible.
7. When engine starts, release the starter grip and allow
the rope to recoil.
8. If the choke lever was moved to the "CLOSED" position
to start the engine, gradually move it to the "OPEN"
position (Figure 18) as the engine warms up. If the
engine has not started, repeat steps 1 through 6.
CHOKE
LEVER
OPEN
Figure 18. Choke Lever (Open)
PAGE 20 — MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
4. When the direction control lever is the neutral position,
the machine vibrates staying at the same location
OPERATION
CAUTION
ALWAYS follow all safety rules in the safety
NOTICE
NEVER stop the engine suddenly while working at
high speeds.
section of this manual before operating
compactor.Keep work area clear of debris
and other objects that could cause bodily
injury or damage to the compactor.
5. Compactor traveling speed may drop on soils which
contain clay, however there may be cases where
traveling speed drops because the compaction plate
does not leave the ground surface easily due to the
composition of the soil. To rectify this problem do the
following:
1. Once the engine has started, move the engine throttle
lever quickly to the operation position (Figure 20).
• Check the bottom plate to see if clay or equivalent
material has been lodged in the plate mechanism. If
so, wash with water and remove.
Operation
position
• Remember the compactor does not work as efficiently
on clay or soils that have a high moisture content level.
Handle
Idle position
Throttle lever
• If the soil has a high moisture level, dry soil to
appropriate moisture content level or carry out
compaction twice.
Figure 20. Throttle Lever (Operation Position)
STOPPING THE ENGINE
Normal Shutdown
2. With the throttle lever in the run position, the engine
speed should be around 2,300 RPM, therefore
engaging the centrifugal clutch.
1. Move the throttle lever to the idle position (Figure 22)
and run the engine for three minutes at low speed.
NOTICE
ALWAYS move the throttle lever quickly without
hesitation, because increasing the engine speed slowly
causes the clutch to slip.
Operation
position
3. Using the direction control lever, move the machine
backward or forward (Figure 21). When the direction
control lever is pushed forward, the machine moves
forward. When pulled backward, the machine moves
backward.
Handle
Idle position
Reverse
Neutral
Throttle lever
Forward
Figure 22. Throttle Lever (Idle)
Direction
control lever
Figure 21. Direction Control Lever
MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)— PAGE 21
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
2. Place the engine ON/OFF switch (Figure 23) in the
OFF position.
Figure 23. Engine ON/OFF Switch (OFF Position)
3. Place the fuel shut-off lever (Figure 24) in the OFF
position.
Figure 24. Fuel Valve Lever (OFF)
Emergency Shutdown
1. Move the throttle lever quickly to the IDLE position, and
place the engine ON/OFF switch in the OFF position.
PAGE 22 — MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
General Cleanliness
GENERAL MAINTENANCE
Clean the compactor daily. Remove all dust and debris
buildup (mud, clay etc.).If the compactor is steam-cleaned,
ensure that lubrication is accomplished AFTER steam
cleaning.
General maintenance practices are crucial to the
performance and longevity of your compactor. This
equipment requires routine cleaning, inspection and
lubrication. Refer to Table 5 and Table 6 for scheduled
engine and compactor maintenance.
NOTICE
The following maintenance procedures can prevent serious
compactor damage or malfunctioning.
Inspection and other services should always be carried
out on hard and level ground with the engine shut down.
NOTICE
NOTICE
Refer to HONDA engine manual supplied with your
compactor for more detailed engine maintenance and
troubleshooting.
The inspection intervals listed in the maintenance tables
are for operation under normal conditions. Adjust your
inspection intervals based on the number hours plate
compactor is in use, and particular working conditions.
CAUTION
ALWAYS allow the engine to cool before
servicing.NEVER attempt any maintenance
work on a hot engine.
CAUTION
ALWAYS disconnect the spark plug wire from the spark
plug and secure away from the engine before performing
maintenance or adjustments on the machine.
WARNING
Some maintenance procedures may
require the engine to be run. Ensure
that the maintenance area is well
ventilated. Gasoline engine exhaust
contains poisonous carbon monoxide
gas that can cause unconsciousness
and may result in DEATH.
MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)— PAGE 23
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
To make sure your plate compactor is always in good
working condition before using, carry out the maintenance
inspection in accordance with Table 5 and Table 6.
ENGINE MAINTENANCE
Perform engine maintance as listed in Table 5.
Table 5. Engine Maintenance Schedule
First Every 3
Month or Months or Months or Year or
Every 6
Every
Every 2
Years or
200 hrs
Description (3)
Operation
Before
10 hrs
25 hrs
50 hrs
100 hrs
CHECK
CHANGE
CHECK
X
Engine Oil
Air Cleaner
X
X
X
CHANGE
X (1)
All Nuts and
Bolts
Re-tighten If
Necessary
CHECK-CLEAN
REPLACE
CHECK
X
X
Spark Plug
X
Cooling Fins
Spark Arrester
Fuel Tank
CLEAN
X
X
CLEAN
Fuel Filter
CHECK
X
Idle Speed
CHECK-ADJUST
X (2)
Valve Clearance CHECK-ADJUST
Fuel lines CHECK
X (2)
Every 2 years (replace if necessary) (2)
1. Service more frequently when used in DUSTY areas.
2. These items should be serviced by your service dealer, unless you have the proper tools and are mechanically proficient.
Refer to the HONDA Shop Manual for service procedures.
3. For commercial use, log hours of operation to determine proper maintenance intervals.
PAGE 24 — MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
TIGHTENING TORQUE
MACHINE INSPECTION
Reference Table 7 below (Tightening Torque ), for retight-
ening of nuts and bolts.
Perform machine inspection as listed in Table 6.
Table 7. Tightening Torque (in. kg/cm Diameter)
Table 6. Machine Inspection
Material 6mm
8mm
150
250
400
10mm
12mm
14mm 16mm 18mm
20mm
2,000
3,800
5,600
Interval
Check
Machine
Solution
4T
70
300
500
750 1,100 1,400
Clean if necessary.
Repair fuel leaks.
Repair fuel leaks.
Add oil if necessary.
Add oil if necessary.
Clean/Replace
6-8T
11T
100
150
500
800
1,300 2,000 2,700
2,000 2,900 4,200
Fuel Tank For Leaks
Fuel System for Leaks
Engine Oil
800
1,200
*
100 (6mm) 300 ~ 350 (8mm) 650 ~ 700 (10mm)
In case counter-part is of aluminum
**
Vibrator Oil
Bolt threads used with this machine are all right handed
Air Cleaner Element
Guard Frame
Material and quality of material is marked on each bolt, and screw.
Inspect/deformations
Replace if damaged.
Check/Repair Leaks
Daily Before Starting
Shock Absorber
Hydraulic pump
ENGINE AIR CLEANER
DANGER
Check/Repair leaks,
Inspect for wear
Hydraulic Pipe System
Direction Control Lever
Duct Hose
Check bolts/nuts,
Inspect for wear
DO NOT use gasoline or low flash point
solvents for cleaning the air cleaner. The
possibility exists of fire or explosion which
can cause damage to the equipment and
severe bodily harm or even DEATH!
Check for crack/
damage
Replace only after
first 20 hrs.
Every 20 Hours
Every 100 Hours
Engine Oil/Oil Filter
Engine Oil
Change
Wash
CAUTION
Engine Oil Filter
Check oil level.
Check for leaks/dirt.
Vibrator Oil
Hydraulic Oil
V-Belt
Wear protective equipment such as
approved safety glasses or face shields
and dust masks or respirators when
cleaning air filters with compressed air.
Check oil level.
Check for leaks.
Inspect, replace if
damaged or worn.
This engine is equipped with a replaceable, high-density
paper air cleaner element. See Figure 25 for air cleaner
components.
Inspect, replace if not
working properly.
Clutch
Every 200 hours
Replace bolts
if deformed or
elongated.
Engine Bolts
1. Remove the air cleaner cover and foam filter element.
Vibrator Oil
Fuel Filter
Change
Change
Change
Change
Replace
2. Tap the paper filter element several times on a hard
surface to remove dirt, or blow compressed air not
exceeding 30 psi (207 kPa, 2.1 kgf/cm2) through the
filter element from the inside out. NEVER brush off
dirt. Brushing will force dirt into the fibers. Replace the
paper filter element if it is excessively dirty.
Every 300 hours
Every 2 years
Hydraulic Oil
Engine Oil Filter
Fuel Lines
MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)— PAGE 25
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
2
Lock
Dust exhaust
1
BLOW COMPRESSED
AIR FROM THE
INSIDE OUT
Figure 27. Latching Dust Pot
ENGINE OIL
NOTICE
Drain the engine oil when the oil is warm.
1. Remove the oil drain bolt (Figure 28). and sealing
washer and allow the oil to drain into a suitable
container.
Figure 25. Engine Air Cleaner
2. Replace engine oil with recommended type oil as listed
in Table 4. For engine oil capacity, see Table 2 (Engine
Specifications). DO NOT overfill.
3. Clean foam element in warm, soapy water or
nonflammable solvent. Rinse and dry thoroughly. Dip
the element in clean engine oil and completely squeeze
out the excess oil from the element before installing.
3. Reinstall drain bolt with sealing washer and tighten
securely.
NOTICE
Operating the engine with loose or damaged air cleaner
components could allow unfiltered air into the engine
causing premature wear and failure.
CYCLONE CLEANER
Engine oil drain
(Drain bolt)
Always clean the dust pot. A clogged dust pot reduces
cyclone effect with cleaner element wearing easily.
1. Unlatch and remove dust pot (Figure 26).
Figure 28. Draining Engine Oil
Latch
Dust exhaust
Dust pot
Figure 26. Unlatching Dust Pot
2. Clean dust pot with water and neutral detergent.
3. Return dust pot to air cleaner and latch securely.
PAGE 26 — MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
HYDRAULIC OIL
7. With the direction control lever at the forward-most
position, secure the guard frame with a rope to
immobilize (Figure 31).
1. With the handle in vertical position, remove the plug
cap from the hydraulic pump (Figure 29).
Forward-most position
Guard frame
Plug cap
Breather
plug
OIL LEVEL
Direction
control lever
Hydraulic
pump
Figure 29. Removing Plug/Breather Cap
Figure 31. Direction Control Lever
(Forward Position)
2. Remove the breather plug with a 24 mm wrench at the
top of the hydraulic hydraulic pump.
8. Pour hydraulic oil (550 cc) to the hydraulic pump
breather plug attachment hole (Figure 29).
3. Remove the hydraulic hose connected to the cylinder
on the vibrator side (Figure 30).
9. Remove the air releasing plug of vibrator cylinder. Oil
will then come out from the air releasing plug. After air
bubbles stop coming out, reattach the plug. Tighten
securely (Figure 30).
Air releasing plug
Hydraulic hose
10. Release the direction control lever and move the lever
forward and reverse several times (until no air bubbles
are seen). Keep the lever at the forward position for
10 seconds every time. (Because the check valve is
opened at the maximum forward position and air bubble
will come out from the oil tank of the hydraulic pump).
Cylinder
Figure 30. Removing Hydraulic Hose
4. Set the run lever to reverse.
11. In case the air bleeding is insufficient, repeat steps 9
and 10.
12. Attach the hydraulic pump breather plug and put on
the plug cap. After making sure the hydraulic oil in the
pump is at OIL LEVEL, attach the breather plug.
5. Drain the hydraulic oil from the pump.
6. After the oil is drained, attach the hydraulic hose again
to the cylinder on the vibrator side.
CAUTION
DO NOT exceed OIL LEVEL of hydraulic oil. If the level
is higher, oil will burst out from the breather plug.
MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)— PAGE 27
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
SPARK PLUG
SPARK ARRESTER CLEANING
NOTICE
Clean the spark arrester every year or 100 hours.
NEVER use a spark plug of incorrect heat range.
1. Remove the 4 mm screw (3) from the exhaust deflector,
then remove the deflector. See (Figure 34).
1. Remove and clean spark plug (Figure 32) with a wire
brush if it is to be reused. Discard spark plug if the
insulator is cracked or chipped.
2. Remove the 5 mm screw (4) from the muffler protector,
then remove the muffler protector.
2. Using a feeler gauge adjust spark plug gap to 0.028
~0.031 inch (0.7~0.8 mm).
3. Remove the 4 mm screw from the spark arrestor, then
remove the spark arrester.
3. Thread spark plug into cylinder hole by hand to prevent
cross-threading, then tighten securely.
GAP
5MM SCREW (4)
.028 - .031 IN.
(0.7- 0.8 MM.)
DEFLECTOR
4MM SCREW (3)
MUFFLER
PROTECTOR
4MM SCREW (1)
Figure 32. Spark Plug Gap
V-BELT
Visually examine the V-belt (Figure 33) and determine if it
is full of tiny cracks, frayed, has pieces of rubber missing,
is peeling or otherwise damaged.
SPARK
ARRESTER
Also, examine the belt and determine if it is oil soaked or
"glazed " (hard shiny appearance on the sides of the belt).
Either of these two conditions can cause the belt to run hot,
which can weaken it and increase the danger of it breaking.
Figure 34. Spark Arrester Removal
4. Carefully remove carbon deposits from the spark
arrester screen (Figure 35) with a wire brush.
WIRE
If the V-belt exhibits any of the above wear conditions
replace the V-belt immediately.
OIL SOAKED
BRUSH
SPARK
ARRESTER
SCREEN
CORD FAILURE
GLAZED
WORN BACK
COVER
Figure 35. Cleaning The Spark Arrester
BROKEN
5. If the spark arrester is damaged and has breaks or
holes, replace with a new one.
MISSING RUBBER
CRACKS
SIDEWALL
WEAR
6. Reinstall the spark arrester and muffler protector in
reverse order of disassembly.
Figure 33. V-Belt Inspection
PAGE 28 — MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
STORAGE
1. Wash off dirt and soil from every part with water.While
washing, be careful not to let the water splash on the
electric components such as the engine muffler.
2. Cover the machine to prevent dust and dirt buildup.
3. Store the machine in a dry area away from direct
sunlight.
4. Do not leave the machine outdoors. Keep it indoors.
5. When not used for a long period of time, drain the fuel
from the fuel tank.
6. When the machine is used after a long storage period,
check the level of engine oil before using.
MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)— PAGE 29
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING (COMPACTOR)
Troubleshooting (Compactor)
Symptom
Possible Problem
Clutch slips?
Solution
Adjust or replace clutch.
Adjust or replace V-belt.
Fill to correct level.
V-belt slips?
Excessive oil in vibrator?
Check vibrator assembly for any
worn or defective parts, replace any
defective parts.
Travel speed low and vibration
weak.
Trouble in vibrator internals?
Aeration in hydraulic oil for for travel
reversing system?
Purge air in hydraulic oil. (Bleed plug)
Engine speed incorrect?
Set engine speed to correct RPM.
Check hydraulic pump.
Hydraulic pump problems?
Direction Control Lever installation
wrong?
Correct installation of lDirection
Control Lever.
Broken or defective oil hose?
Aeration in hydraulic oil?
Replace oil hose.
Travels forward or backward but
unable to switch direction.
Purge air in hydraulic oil. (Bleed plug)
Fill to correct level.
Excessive oil in reversing system?
Hydraulic pump clogged with trash?
Clean valve inside hydraulic pump.
Check piston bearing in cylinder for
leakage.
Cylinder piston bearing failure?
V-belt disengaged or slips?
Clutch slips?
Engage V-belt, adjust or replace.
Adjust clutch, replace if necessary.
Check vibrator and correct problem.
Does not travel in forward or reverse
Vibrator locks?
Check piston bearing in cylinder for
leakage at USH packing.
Cylinder piston bearing failure?
Piston inside hydraulic pump not
moving smoothly?
Adjust or replace.
Adjust or replace.
Direction Control Lever operating
resistance for reverse is high.
Vibrator cylinder piston does not move
smoothly
PAGE 30 — MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING (ENGINE)
Troubleshooting (Engine)
Possible Problem
Spark plug bridging?
Symptom
Solution
Check gap, insulation or replace spark plug.
Clean or replace spark plug.
Carbon deposit on spark plug?
Short circuit due to deficient spark plug
insulation?
Check spark plug insulation, replace if worn.
Improper spark plug gap?
Fuel reaching carburetor?
Water in fuel tank?
Set to proper gap.
Check fuel line.
Flush or replace fuel tank.
Replace fuel filter.
Fuel filter clogged?
Stuck carburetor?
Check float mechanism.
Check transistor ignition unit.
Difficult to start, fuel is available, but no spark at
spark plug.
Spark plug is red?
If insufficient compression, repair or replace
engine. If injected air leaking, correct leak. If
carburetor jets clogged, clean carburetor.
Spark plug is bluish white?
Check transistor ignition unit is broken, and
replace defective unit. Check if voltage cord
cracked or broken and replace. Check if spark
plug if fouled and replace.
No spark present at tip of spark plug?
No oil?
Add oil as required.
Oil pressure alarm lamp blinks upon starting? (if Check automatic shutdown circuit, "oil sensor".
applicable)
(if applicable)
ON/OFF switch is shorted?
Check switch wiring, replace switch.
Replace ignition coil.
Ignition coil defective?
Difficult to start, fuel is available, and spark is
present at the spark plug.
Improper spark gap, points dirty?
Condenser insulation worn or short circuiting?
Spark plug wire broken or short circuiting?
Set correct spark gap and clean points.
Replace condenser.
Replace defective spark plug wiring.
Flush fuel system, replace with correct type of
fuel.
Wrong fuel type?
Difficult to start, fuel is available, spark is
present and compression is normal.
Water or dust in fuel system?
Air cleaner dirty?
Flush fuel system.
Clean or replace air cleaner.
Close choke.
Choke open?
Suction/exhaust valve stuck or protruded?
Piston ring and/or cylinder worn?
Reseat valves.
Replace piston rings and/or piston.
Difficult to start, fuel is available, spark is
present and compression is low.
Cylinder head and/or spark plug not tightened
properly?
Torque cylinder head bolts and spark plug.
Head gasket and/or spark plug gasket damaged?
No fuel in fuel tank?
Replace head and spark plug gaskets.
Fill with correct type of fuel.
Apply lubricant to loosen fuel cock lever,
replace if necessary.
Fuel cock does not open properly?
No fuel present at carburetor.
Fuel filter/lines clogged?
Fuel tank cap breather hole clogged?
Air in fuel line?
Replace fuel filter.
Clean or replace fuel tank cap.
Bleed fuel line.
MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)— PAGE 31
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING (ENGINE)
Troubleshooting (Engine) - continued
Possible Problem
Air cleaner dirty?
Symptom
Solution
Clean or replace air cleaner.
Check float adjustment, rebuild carburetor.
Clean or replace spark plug.
Set to proper gap.
Improper level in carburetor?
Defective spark plug?
Weak in power, compression is proper and
does not misfire.
Improper spark plug?
Flush fuel system and replace with correct
type of fuel.
Water in fuel system?
Weak in power, compression is proper but
misfires.
Dirty spark plug?
Clean or replace spark plug.
Replace ignition coil.
Ignition coil defective?
Spark plug heat value incorrect?
Wrong type of fuel?
Replace with correct type of spark plug.
Replace with correct type of fuel.
Clean cooling fins.
Cooling fins dirty?
Engine overheats.
Clear intake of dirt and debris. Replace air
cleaner elements as necessary.
Intake air restricted?
Oil level too low or too high?
Governor adjusted incorrectly?
Governor spring defective?
Fuel flow restricted?
Adjust oil to proper level.
Adjust governor.
Rotational speed fluctuates.
Replace governor spring.
Check entire fuel system for leaks or clogs.
Recoil mechanism clogged with dust and dirt? Clean recoil assembly with soap and water.
Recoil starter malfunctions. (if applicable)
Spiral spring loose?
Replace spiral spring.
Ensure tight, clean connections on battery
and starter.
Loose, damaged wiring?
Starter malfunctions.
Battery insufficiently charged?
Recharge or replace battery.
Replace starter.
Starter damaged or internally shorted?
Check and clean valves. Check muffler and
replace if necessary.
Over-accumulation of exhaust products?
Wrong spark plug?
Burns too much fuel.
Replace spark plug with manufacturer's
suggested type.
Lubricating oil is wrong viscosity?
Worn rings?
Replace lubricating oil with correct viscosity.
Replace rings.
Exhaust color is continuously "white".
Air cleaner clogged?
Clean or replace air cleaner.
Adjust choke valve to correct position.
Choke valve set to incorrect position?
Carburetor defective, seal on carburetor
broken?
Exhaust color is continuously "black".
Replace carburetor or seal.
Poor carburetor adjustment, engine runs too
rich?
Adjust carburetor.
ON/OFF device not activated ON?
Battery disconnected or discharged?
Ignition switch/wiring defective?
Turn on ON/OFF device.
Check cable connections. Charge or replace
battery
Will not start, no power with key "ON". (if
applicable)
Replace ignition switch. Check wiring.
PAGE 32 — MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)— PAGE 33
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLANATION OF CODE IN REMARKS COLUMN
The following section explains the different symbols and
QTY. Column
remarks used in the Parts section of this manual. Use the
help numbers found on the back page of the manual if there
are any questions.
Numbers Used — Item quantity can be indicated by a
number, a blank entry, or A/R.
A/R (As Required) is generally used for hoses or other
parts that are sold in bulk and cut to length.
NOTICE
The contents and part numbers listed in the parts
section are subject to change without notice.Multiquip
does not guarantee the availability of the parts listed.
A blank entry generally indicates that the item is not sold
separately.Other entries will be clarified in the “Remarks”
Column.
SAMPLE PARTS LIST
REMARKS Column
NO. PART NO. PART NAME
QTY. REMARKS
Some of the most common notes found in the “Remarks”
Column are listed below. Other additional notes needed
to describe the item can also be shown.
1
2%
12345
BOLT .....................1 .....INCLUDES ITEMS W/%
WASHER, 1/4 IN. ..........NOT SOLD SEPARATELY
WASHER, 3/8 IN. ..1 .....MQ-45T ONLY
2% 12347
3
4
12348
12349
HOSE ..................A/R ...MAKE LOCALLY
BEARING ..............1 .....S/N 2345B AND ABOVE
Assembly/Kit — All items on the parts list with the
same unique symbol will be included when this item is
purchased.
NO. Column
Indicated by:
Unique Symbols — All items with same unique symbol
(@, #, +, %, or >) in the number column belong to the
same assembly or kit, which is indicated by a note in the
“Remarks” column.
“INCLUDES ITEMS W/(unique symbol)”
Serial Number Break — Used to list an effective serial
number range where a particular part is used.
Duplicate Item Numbers — Duplicate numbers indicate
multiple part numbers, which are in effect for the same
general item, such as different size saw blade guards in
use or a part that has been updated on newer versions
of the same machine.
Indicated by:
“S/N XXXXX AND BELOW”
“S/N XXXX AND ABOVE”
“S/N XXXX TO S/N XXX”
Specific Model Number Use — Indicates that the part
is used only with the specific model number or model
number variant listed. It can also be used to show a
part is NOT used on a specific model or model number
variant.
NOTICE
When ordering a part that has more than one item
number listed, check the remarks column for help in
determining the proper part to order.
Indicated by:
PART NO. Column
“XXXXX ONLY”
“NOT USED ON XXXX”
Numbers Used — Part numbers can be indicated by a
number, a blank entry, or TBD.
“Make/Obtain Locally” — Indicates that the part can
be purchased at any hardware shop or made out of
available items.Examples include battery cables, shims,
and certain washers and nuts.
TBD (To Be Determined) is generally used to show a
part that has not been assigned a formal part number
at the time of publication.
A blank entry generally indicates that the item is not sold
separately or is not sold by Multiquip. Other entries will
be clarified in the “Remarks” Column.
“Not Sold Separately”— Indicates that an item cannot
be purchased as a separate item and is either part of an
assembly/kit that can be purchased, or is not available
for sale through Multiquip.
PAGE 34 — MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
SUGGESTED SPARE PARTS
MVH408GH PLATE COMPACTOR WITH HONDA GX390UT2SMXC GASOLINE ENGINE
1 to 5 units
Qty.
P/N
Description
4............939010010............SHOCK ABSORBER, STOPPER
4............939010260............SHOCK ABSORBER 110X60H
2............070200453............V-BELT B-45
1............956100069............THROTTLE WIRE
3............0650140480 .........SPARK PLUG
1............28462ZE3W01 .....ROPE, RECOIL STARTER
3 ...........17210ZE3505 ......AIR CLEANER ELEMENT
1............17218ZE3505 ......FILTER, OUTER
1............17620Z4H900 ......FUEL TANK CAP CP.
2............17672Z4H000 ......FILTER, FUEL
NOTICE
Part numbers on this Suggested Spare Parts list may
supersede/replace the part numbers shown in the
following parts lists.
MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)— PAGE 35
Download from Www.Somanuals.com. All Manuals Search And Download.
VIBRATING PLATE ASSY.
24
25
22
23
19
20
18
8
7
19
20
6
18
10
9
14
2
3
5
16
15
4
12
1
11
30
32
31
OPTION
PAGE 36 — MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
VIBRATING PLATE ASSY.
NO.
1
2
3
4
5
6
7
8
PART NO.
468121200
465460670
953402930
953400270
953405260
939010260
020316130
030216400
001221635
030216400
001221830
58407
939010010
020310080
030210250
468352110
014208020
030208200
467351790
050103250
014208020
030208200
467219050
012218050
58407
PART NAME
VIBRATING PLATE
OIL GAUGE
COPPER PACKING 19X30X1
PLUG 1/4X14 10L
PACKING 1/4 (CU)
SHOCK ABSORBER 110X60H
NUT M16
WASHER, LOCK M16
BOLT 16X35 T
WASHER, LOCK M16
BOLT 18X30 T
WASHER, LOCK M18 .......................................8................REPLACES 030218460
SHOCK ABSORBER, STOPPER
NUT M10
WASHER, LOCK M10
COVER, VIBRATING PLATE
BOLT 8X20 T .....................................................8................REPLACES 001220820
QTY.
REMARKS
1
1
1
1
1
4
4
4
4
4
8
9
10
11
12
14
15
16
18
19
20
22
23
24
25
30
31
32
4
4
4
2
WASHER, LOCK M8
COVER, VIBRATOR
O-RING G-325
BOLT 8X20 T ....................................................18...............REPLACES 001220820
WASHER, LOCK M8
EXTENSION PLATE
8
1
1
18
2
BOLT 18X50 T ...................................................8................REPLACES 001221850
WASHER, LOCK M18 .......................................8 ...............REPLACES 030218460
MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)— PAGE 37
Download from Www.Somanuals.com. All Manuals Search And Download.
VIBRATOR ASSY.
7
7
6
A
6
5
2
8
1
23
3
C
41
6
24
12
12
4
22
5
21
20
20
6
B
13
11
14
34
16
35
1
33
36
15
16
27
30
A
D
D
C
B
29
30
1
31
32
40
42
28
1
44
43
17
46
51
49
48
47
52
PAGE 38 — MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
VIBRATOR ASSY.
NO.
1
2
3
4
5
6
7
8
PART NO.
047920120
457212410
951405370
456327150
080200550
468352210
009120301
060105030
456337670
009120302
456337380
456010010
467351910
040006911
953010030
042506000
0080000010
455435051
455010070
080100260
467352540
467219070
954010020
050101050
001720812
953404600
959408880
0105091025
030210250
031110160
465345090
951404970
456437920
012212035
030212300
467351920
014208020
030208200
0401450080
468218960
001520856
PART NAME
QTY.
4
1
1
1
2
4
2
1
1
2
1
1
1
2
1
2
REMARKS
ROLLER BEARING NJ310EMC4
ROTARY SHAFT, DRIVE
KEY 15X10X39 RR
GEAR, DRIVE
STOP RING S-55
ECCENTRIC ROTATOR
SOCKET HEAD BOLT 16X40 T
OIL SEAL SB-50729
ROTARY SHAFT, DRIVEN/304B
SOCKET HEAD BOLT 16X30 T
PISTON ROD
KNOCK PIN 10X70
GEAR (DRIVEN)
BEARING 6911
SEAL CAP SC75-8N
BEARING 6000ZZSG
STOP RING S-10 ..............................................1................REPLACES 080200100
PISTON, 22.4D
PACKING VSH-22.4X30X5
STOP RING R-26
BEARING COVER
CYLINDER (R)
CONNECTOR PT, PF1/4
O-RING G-105
11
12
13
14
15
16
17
20
21
22
23
24
27
28
29
30
31
32
33
34
35
36
40
41
42
43
44
46
47
48
49
51
52
1
1
1
1
1
1
2
1
1
1
FLANGE BOLT8X12
COPPER PACKING 8.2X16X1.6
CLIP 15 (M10)
BOLT 10X25 T ...................................................8................REPLACES 001221025
WASHER, LOCK M10
WASHER, FLAT M10
PULLEY
KEY 12X8X30 R
WASHER, PULLEY
BOLT 12X35 T ...................................................1................REPLACES 001221235
WASHER, LOCK M12
GUIDE, BELT COVER
BOLT 8X20 T .....................................................2................REPLACES 001220820
WASHER, LOCK M8
WASHER, FLAT M8 ..........................................2................REPLACES 031108160
BELT COVER, LOWER
SOCKET HEAD BOLT 8X80 T
8
8
1
1
1
1
1
2
1
5
MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)— PAGE 39
Download from Www.Somanuals.com. All Manuals Search And Download.
BASE AND ENGINE ASSY.
53
52
54
30
31
45
27
26
C
51
29
26
24
25
28
B
41
42
43
62
40
25
61
49
7
48
16
47
A
67
2
8
C
66
65
55
56
33
3
4
5
15
14
22
19
38
39
35
43
42
70
71
34
41
17
69
18
B
37
A
46
13
12
11
1
PAGE 40 — MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
BASE AND ENGINE ASSY.
NO.
1
2
3
4
5
7
8
PART NO.
468121260
912239016
0105051045
030210250
031110160
468352240
009110071
468352120
092006010
468467050
952408810
456343340
951400110
952406050
011208030
030208200
070200453
954407310
0091720000
0211140020
0401140030
465459390
464457380
014208020
030208200
467121100
467351800
001521054
468352140
001521435
030214350
468121230
PART NAME
BASE L100
ENGINE ASSY., GX390UT2SMXC
QTY.
1
1
REMARKS
BOLT 10X45 T ...................................................4................REPLACES 001221045
WASHER, LOCK M10
WASHER, FLAT M10
BELT COVER, IN
SOCKET HEAD BOLT 10X25 T
DUST COVER
FLAT HEAD SCREW 6X10
PLATE, BELT COVER
SPACER 25X31.8X10
CLUTCH ASSY.
KEY 7X7X35
SPECIAL WASHER
4
4
1
4
1
6
1
1
1
1
1
11
12
13
14
15
16
17
18
19
22
24
25
26
27
28
29
30
31
33
34
35
37
38
39
40
BOLT 8X30 T .....................................................1................REPLACES 001220830
WASHER, LOCK M8
V-BELT B-45
UNION, DRAIN
HOSE CLAMP
GASKET
PLUG
DRAIN HOSE
DRAIN JOINT
BOLT 8X20 T .....................................................1................REPLACES 001220820
WASHER, LOCK M8
BELT COVER (OUT)
DUST SPONGE (OUT)
SOCKET HEAD BOLT 10X70 T
FRONT BUMPER
SOCKET HEAD BOLT 14X35 T
WASHER, LOCK M14
FRONT COVER
1
1
1
2
2
1
1
1
1
1
2
4
1
2
2
1
MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)— PAGE 41
Download from Www.Somanuals.com. All Manuals Search And Download.
BASE AND ENGINE ASSY. CONTINUED
53
52
54
30
31
45
27
26
C
51
29
26
24
25
28
B
41
42
43
62
40
25
61
49
7
48
16
47
A
67
2
8
C
66
65
55
56
33
3
4
5
15
14
22
19
38
39
35
43
42
70
71
34
41
17
69
18
B
37
A
46
13
12
11
1
PAGE 42 — MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
BASE AND ENGINE ASSY. CONTINUED
NO.
41
42
43
45
46
47
48
49
51
52
53
54
55
56
61
62
65
66
67
69
70
71
PART NO.
001221445
030214350
031114260
468121240
001521435
031114260
030214350
020314110
467466800
467466810
009120424
617465130
030206150
022710607
90131ZE3790
031112230
402010110
58151
PART NAME
BOLT 14X45 T
WASHER, LOCK M14
WASHER, FLAT M14
CENTER COVER
SOCKET HEAD BOLT 14X35 T
WASHER, FLAT M14
WASHER, LOCK M14
NUT M14
RUBBER COVER, UPPER
STOPPER, COVER
SOCKET HEAD BOLT 6X25 T
COLLAR 6.2X7.8X4.5
WASHER, LOCK M6
NYLON NUT M6
QTY.
4
4
4
1
4
4
4
4
1
1
2
2
2
2
1
REMARKS
DRAIN JOINT
WASHER, DRAIN PLUG M12 ..........................1................REPLACES 9410912000
COIL SPRING ...................................................1................REPLACES 0830000010
WASHER, FLAT M5 ..........................................1................REPLACES 031105080
CLAMP COMPL
CLIP D6 (FOR M10)
2067550101
959407260
012210015
030210250
1
1
BOLT 10X15 T ...................................................1................REPLACES 001221015
WASHER, LOCK M10
1
MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)— PAGE 43
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRIC DEVICE ASSY.
26
19
20
90
25
106
27
18
103
104
113
114
C
21
108
91
110
96
92
107
111
93
94
23
A
B
22
ENGINE
105
B
101
100
75
112
C
102
A
PAGE 44 — MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRIC DEVICE ASSY.
NO.
18
19
20
21
22
23
25
26
27
75
90
91
92
PART NO.
468218970
011006010
030206150
009120413
030206150
020106050
467466950
009110062
022710607
515010070
009110072
952407930
58151
PART NAME
REAR COVER
QTY.
REMARKS
1
BOLT 6X10 T .....................................................8................REPLACES 001220610
WASHER, LOCK M6
SUNK HEAD BOLT 6X15
WASHER, LOCK M6
8
6
6
NUT M6 .............................................................6................REPLACES 020306050
RUBBER COVER, REAR
SOCKET HEAD SCREW 6X20
NYLON NUT M6
GROMMET
PAN HEAD SCREW 5X35
COLLAR 6X10X13.5
1
3
3
1
2
2
WASHER, FLAT M5 ..........................................2................REPLACES 031105080
93
94
96
030205130
022710506
955010311
955010307
955010308
959026828
955407970
454010020
2067550101
955301010
468467570
467466980
020108060
959021812
515450380
955407970
454010020
WASHER, LOCK M5
NYLON NUT M5
TACHO/HOUR METER
CLIP BELT
CURL CORD
RUBBER TUBE L=850
WIRING FIXED BASE
CLAMP TC-100
2
2
1
1
1
1
3
3
1
1
1
1
100
101
102
103
104
105
106
107
108
110
111
112
113
114
CLAMP COMPL
STOP SWITCH,ENGINE
READ CORD
LEAD WIRE (SW-GROUND)
NUT M8 .............................................................1................REPLACES 020308060
SPIRAL TUBE 6D-800L
WIRE HARNESS/MRH-600, 700
WIRING FIXED BASE
CLAMP
1
1
3
3
MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)— PAGE 45
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROL ASSY.
52
57
58
50
56
58
57
46
47
70
48
76
55
72
73
83
74
49
82
73
80
81
62
60
61
84
43
59
45
44
53
12
67
16
78
77
75
71
51
36
19
63
37
40
38
39
69
68
20
18
1
64
7
13
3
21
28
9
10
85
4
5
25
26
11
29
10
3
8
9
4
5
27
35
34
7
2
23
22
13
14
8
11
15
PAGE 46 — MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROL ASSY.
NO.
1
2
3
4
5
7
8
9
PART NO.
467351950
467351960
012212035
030212300
031112230
456336400
456449940
025306016
456449930
032124400
001221681
0401450160
020316130
020416100
467121180
455434950
455010030
020412070
022411635
939010060
020310080
959408930
011206020
030206150
952404470
020106050
501402870
501402880
959403460
020310080
456449980
953405260
031110160
467351980
467467340
467467350
0105050616
030206150
952404470
464457930
468219160
PART NAME
HANDLE BRACKET (R)
HANDLE BRACKET (L)
QTY.
1
1
REMARKS
BOLT 12X35 T ...................................................4................REPLACES 001221235
WASHER, LOCK M12
WASHER, FLAT M12
RUBBER COUPLING
SHOCK ABSORBER
4
4
2
2
SPRING PIN 6X16 ............................................2................REPLACES 025406016
10
11
12
13
14
15
16
18
19
20
21
22
23
25
26
27
28
29
34
35
36
37
38
39
40
43
44
45
46
47
48
49
50
RUBBER PLATE
CONICAL SPRING WASHER M24
BOLT 16X250 T
WASHER, FLAT M16 ........................................2................REPLACES 031116260
NUT M16
NUT M16, H=10
COLUMN, HANDLE BAR
SPINDLE
2
2
1
1
1
1
1
1
1
1
1
KNOB
NUT M12, H=7
WING NUT M16
SHOCK ABSORBER 60
NUT M10, H=6 ..................................................1................REPLACES 020410060
CLIP 15 (M6)
BOLT 6X20 T .....................................................1................REPLACES 001220620
WASHER, LOCK M6
WASHER, FLAT M6 ..........................................1................REPLACES 031106100
NUT M6 .............................................................1................REPLACES 020306050
HANDLE STOPPER
SPRING HANDLE
BALL GRIP 32D-M10
NUT M10, H=6 ..................................................1................REPLACES 020410060
RUBBER PACKING
PACKING 1/4 (CU)
WASHER, FLAT M10
HANDLE COVER, DSY
PACKING (L), HANDLE
PACKING (R), HANDLE
BOLT 6X15 T .....................................................6................REPLACES 001220615
WASHER, LOCK M6
WASHER, FLAT M6 ..........................................6................REPLACES 031106100
1
1
1
1
1
1
1
1
1
1
1
6
RUBBER PIECE (T2)
HYDRAULIC PUMP
1
1
MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)— PAGE 47
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROL ASSY. CONTINUED
52
57
58
50
56
58
57
46
47
70
48
76
55
72
73
83
74
49
82
73
80
81
62
60
61
84
43
59
45
44
53
12
67
16
78
77
75
71
51
36
19
63
37
40
38
39
69
68
20
18
1
64
7
13
3
21
28
9
10
85
4
5
25
26
11
29
10
3
8
9
4
5
27
35
34
7
2
23
22
13
14
8
11
15
PAGE 48 — MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROL ASSY. CONTINUED
NO.
51
52
53
55
56
57
58
59
60
61
62
63
64
67
68
69
70
71
72
73
74
75
76
77
78
80
81
82
83
84
85
PART NO.
954003110
458451630
959021813
464216630
464457400
012010030
030210250
467218900
030210250
031110160
020310080
0105091025
030210250
467467380
959403840
464457420
464457350
014208020
0401450160
458450660
033910080
464457440
464010010
011606025
020106050
464010020
001520520
58151
PART NAME
OIL HOSE
BREATHER CAP
SPIRAL TUBE
TRAVEL LEVER
HANDLE BOSS
QTY.
REMARKS
1
1
1
1
1
BOLT 10X30 T ...................................................2................REPLACES 001221030
WASHER, LOCK M10
HANDLE W/ RUBBER GRIP
WASHER, LOCK M10
WASHER, FLAT M10
NUT M10
BOLT 10X25 T ...................................................2................REPLACES 001221025
WASHER, LOCK M10
THROTTLE LEVER
BAR GRIP, I.D. 12MM
COVER, THROTTLE LEVER
ARM, THROTTLE
SOCKET HEAD BOLT 8X20 T ..........................1................REPLACES 001520820
WASHER, FLAT M16 ........................................1................REPLACES 031116260
WASHER 16.4-35-0. 6
CONICAL WASHER, LOCK 16.3X31.5X1.2
STEEL BALL
2
1
2
2
2
2
1
1
1
1
2
3
1
1
DRY BUSHING
BOLT 6X25 T .....................................................2................REPLACES 001220625
NUT M6 .............................................................2................REPLACES 020306050
ROD END M5
SOCKET HEAD BOLT 5X20 T
1
1
WASHER, FLAT M5 ..........................................1................REPLACES 031105080
020305040
956100069
454010020
NUT M5
THROTTLE WIRE
CLAMP
1
1
1
MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)— PAGE 49
Download from Www.Somanuals.com. All Manuals Search And Download.
NAMEPLATE AND DECALS ASSY.
18
20
6
8
21
2
15
3
19
23
17
16
11
22
7
9
19
4
10
1
13
14
12
5
PAGE 50 — MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
NAMEPLATE AND DECALS ASSY.
NO.
1
2
3
4
5
6
7
8
12
13
14
15
16
17
18
19
20
21
22
23
PART NO.
920204580
920203330
920211060
920211090
920201950
920106760
920214200
920214100
920217130
920217110
920201580
920218390
920205860
920218160
920217880
920217770
920217780
920217630
920214740
920214730
PART NAME
QTY.
1
1
1
1
1
1
1
1
2
2
1
1
1
1
1
2
REMARKS
DECAL, FULL THROTTLE
EAR PROTECTION LABEL
DECAL, CAUTION (LEVER)
DECAL, SHELL TELLUS OIL 32
DECAL, OIL SAE 10W-30
DECAL, STOP-RUN-START
DECAL, CAUTION CYCLONE
DECAL, E/G FIRE WARNING
DECAL, MlKASA MARK (W) 200L
DECAL, MIKASA MARK 35X70
DECAL, MQ MARK 71X55
DECAL, CAUTION
DECAL, V-BELT
DECAL, E/G RPM 3200
DECAL, MODEL
DECAL, MODEL (R, OR)
DECAL, MODEL(L, OR)
PLATE, SERIAL NO...........................................1................CONTACT MQ PARTS DEPT.
1
DECAL, LIFTING POSITION
DECAL, DO NOT LIFT
1
1
MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)— PAGE 51
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX390UT2SMXC — CYLINDER HEAD ASSY.
15
5
11
11
12
12
14
14
13
6
14
7
14
4
3
10
8
2
1
9
9
16
16
PAGE 52 — MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX390UT2SMXC — CYLINDER HEAD ASSY.
NO.
1
2#
3#
4#
5
6
7
8
9
10
11
12
13
14
15
16
PART NO.
PART NAME
HEAD COMP., CYLINDER ................................1................INCLUDES ITEMS W/ #
QTY.
REMARKS
12210Z5T416
12204ZE2306
12205ZE2305
12216ZE2300
12251Z5T003
12310ZE3791
12391ZE2020
90014Z5T000
90042ZE8000
90441ZE2010
92900080320E
9430112200
GUIDE, IN. VALVE (OVERSIZE)
GUIDE, EX. VALVE (OVERSIZE)
CLIP, VALVE GUIDE
1
1
1
1
1
1
1
2
1
2
2
1
4
1
2
GASKET, CYLINDER HEAD
COVER COMP., HEAD
PACKING, HEAD COVER
BOLT, HEAD COVER
BOLT, STUD 8X31.5
WASHER COMP., HEAD COVER
BOLT, STUD 8X32
PIN, DOWEL 12X20
12315ZE3840
957011008000
0650140480
TUBE, BREATHER
BOLT, FLANGE 10X80
SPARK PLUG
CLIP, BREATHER TUBE
17316611000
MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)— PAGE 53
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX390UT2SMXC — CYLINDER BARREL ASSY.
7
10
13
9
3
14
14
11
1
6
12
15
16
8
6
12
PAGE 54 — MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX390UT2SMXC — CYLINDER BARREL ASSY.
NO.
1
3
6
7
8$
9$
10
11
12
13
14
15$
16
PART NO.
PART NAME
BARREL ASSY, CYLINDER/ALERT .................1................INCLUDES ITEMS W/$
QTY.
REMARKS
12000Z5T407
16541ZE3010
90131896650
90446KE1000
91201Z1C003
91201ZE9003
91353671003
9405010000
9410912000
9425110000
957010601200
961006202000
35480ZF6003
SHAFT, GOVERNOR ARM
BOLT, DRAIN PLUG
WASHER 8.2X17X0.8
OIL SEAL
1
2
1
1
OIL SEAL ..........................................................1................REPLACES 91203952771
O-RING 14MM ..................................................1................REPLACES 91353671004
FLANGE NUT M10
1
2
1
2
1
1
WASHER, DRAIN PLUG M12
PIN LOCK 10MM
FLANGE BOLT 6X12
BEARING, RADIAL BALL 6202
SWITCH ASSY., OIL LEVEL
MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)— PAGE 55
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX390UT2SMXC — CRANKCASE COVER ASSY.
10
4
5
11 17
17
12
15
7
16
13
15
8
17
14
15
5
3
6
9
9
2
1
PAGE 56 — MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX390UT2SMXC — CRANKCASE COVER ASSY.
NO.
1
2
3
4
5$
6@
7@
8@
9
PART NO.
PART NAME
COVER ASSY., CRANKCASE/S-TYPE ............1................INCLUDES ITEMS W/@
PACKING, CRANKCASE COVER
CAP ASSY., OIL FILLER ..................................1................INCLUDES ITEM W/ $
CAP ASSY., OIL FILLER ..................................1................INCLUDES ITEM W/ $
QTY.
REMARKS
11300Z8W800
11381Z5T000
15600Z0T820
15600Z1C000
15625Z0T800
16510ZE3000
16531Z0A000
90602ZE1000
90701HC4000
1
PACKING, OIL FILLER CAP
GOVERNOR ASSY. ..........................................1................INCLUDES ITEMS W/ #
2
SLIDER, GOVERNOR
CLIP, GOVERNOR HOLDER
PIN, DOWEL
1
1
2
1
10@ 91201Z1C003
11@ 58176
OIL SEAL
WASHER, FLAT 6MM .......................................1................REPLACES 9410106800
12
957010804000
BOLT, FLANGE 8X40
7
1
1
3
1
3
13@ 961006202000
14@ 961006207000
15@# 16511ZE8000
16@# 16512ZE3000
17@# 16513ZE2000
BEARING, RADIAL BALL 6202
BEARING, RADIAL BALL 6207
WEIGHT, GOVERNOR
HOLDER, GOVERNOR WEIGHT
PIN, GOVERNOR WEIGHT
MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)— PAGE 57
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX390UT2SMXC — CRANKSHAFT ASSY.
6
9
7
8
10
5
PAGE 58 — MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX390UT2SMXC — CRANKSHAFT ASSY.
NO.
5
6
7
8
PART NO.
PART NAME
CRANKSHAFT...................................................1................INCLUDES ITEM W/ #
QTY.
REMARKS
13310ZF6W72
13351Z1C900
92101080250A
90534706010
90741889810
91001ZF6013
WEIGHT, BALANCER
BOLT 8X25
1
1
1
1
1
WASHER, LOCK 8MM
KEY 7X7X33 (YELLOW)
BEARING, RADIAL BALL 6207SH
9
10#
MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)— PAGE 59
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX390UT2SMXC — PISTON ASSY.
5
6
2
5
4
1
3
6
PAGE 60 — MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX390UT2SMXC — PISTON ASSY.
NO.
1
1
1
1
2
2
2
2
PART NO.
PART NAME
QTY.
REMARKS
13010Z5R004
13011Z5R004
13012Z5R004
13013Z5R004
13101Z1C900
13102Z5T800
13103Z5T800
13104Z5T800
13111Z5T000
13200Z1C900
13200Z1C305
RING SET, PISTON (STD)
RING SET, PISTON (0.25)
RING SET, PISTON (0.50)
RING SET, PISTON (0.75)
PISTON (STD)
PISTON (0.25)
PISTON (0.50)
PISTON (0.75)
PIN, PISTON
1
1
1
1
1
1
1
1
1
3
4
4
ROD ASSY., CONNECTING /STD.....................1................INCLUDES W/ %
ROD ASSY., CONNECTING 0.25UN.................1................INCLUDES W/ $
5%$ 90001ZES000
90601ZE3000
BOLT, CONNECTING ROD
CLIP, PISTON PIN 20MM
2
2
6
MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)— PAGE 61
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX390UT2SMXC — CAMSHAFT ASSY.
10
13
12
9
2
4
17
16
6
11
10
1
3
5
8
17
16
6
4
15
3
5
PAGE 62 — MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX390UT2SMXC — CAMSHAFT ASSY.
NO.
1
2
3
4
5
6
8
9
10
11
12
13
15
16
17
PART NO.
PART NAME
QTY.
1
1
2
2
2
2
1
1
2
1
1
1
1
2
2
REMARKS
12209ZE8003
14100Z5T910
14410Z1C000
14431ZE2010
14441ZE2000
14451ZE1013
14711Z5T900
14721Z5T900
14751Z1C000
14771Z88000
14771Z88000
14775ZE2010
14791Z1D000
90012ZE0010
90206ZE1000
SEAL, VALVE STEM
CAMSHAFT ASSY.
ROD, PUSH
ARM, VALVE ROCKER
LIFTER, VALVE
PIVOT, ROCKER ARM
VALVE, IN.
VALVE, EX.
SPRING, VALVE
RETAINER, VALVE SPRING
RETAINER, VALVE SPRING
SEAT, VALVE SPRING
PLATE, PUSH ROD GUIDE
BOLT, PIVOT, 8MM/GX160
NUT, PIVOT ADJUSTING
MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)— PAGE 63
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX390UT2SMXC — RECOIL STARTER ASSY.
5
3
7
11
7
6
8
4
4
2
12
10
13
14
1
PAGE 64 — MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX390UT2SMXC — RECOIL STARTER ASSY.
NO.
1
PART NO.
PART NAME
QTY.
REMARKS
28400ZE3W01ZB STARTER ASSY................................................1................REPLACES 28400ZE3W02ZB
INCLUDES ITEMS W/ #
2#
3#
4#
5#
6#
7#
8#
10#
11#
12
13#
14#
28410ZE3W01ZB CASE CP, RECOIL STARTER
1
1
2
1
1
2
1
28421ZE3W01
28422ZE2W01
28441ZE2W01
28442ZE2W01
28443ZE2W01
28444ZE2W01
28462ZE3W01
90004ZE2W01
957010601000
28461Z5T305
28463Z5T013
PULLEY, RECOIL STARTER
RATCHET, STARTER
SPRING FRICTION
SPRING, STARTER RETURN
SPRING, RATCHET
RETAINER, SPRING
ROPE, RECOIL STARTER ...............................1................REPLACES 28462ZE3W01
SCREW, CENTER
FLANGE BOLT 6X10
GRIP, STARTER
GRIP, REINFORCEMENT
1
3
1
1
MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)— PAGE 65
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX390UT2SMXC — FAN COVER ASSY.
1
6
2
3
7
7
PAGE 66 — MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX390UT2SMXC — FAN COVER ASSY.
NO.
1
2
3
6
PART NO.
16731ZE2003
19610Z5T000ZB COVER CP, FAN/BLACK
PART NAME
CLIP, TUBE
QTY.
REMARKS
1
1
1
1
6
19631Z5T000
81329567020
90013883000
SHROUD
GROMMET, DRAIN HOLE
FLANGE BOLT 6X12
7
MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)— PAGE 67
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX390UT2SMXC — CARBURETOR ASSY.
18
25
17
27
12
1
8
14
24
20
21
16
10
19
22
39
1 13
23
5
11
26
9
2
15
3
1
4
1
1
6
7
PAGE 68 — MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX390UT2SMXC — CARBURETOR ASSY.
NO. PART NO.
1@$%&16010ZE2812
PART NAME
GASKET SET
VALVE SET, FLOAT
QTY.
1
1
REMARKS
2&
3&
16011ZA0931
16013Z1C003
FLOAT SET .......................................................1................INCLUDES ITEM W/ %
CHAMBER SET, FLOAT ....................................1................INCLUDES ITEM W/ $
SCREW SET PILOT
SCREW SET, DRAIN
SCREW SET
4%& 16015Z5T901
5& 16016ZH7W01
6$%& 16024Z5T901
7$%& 16028Z5T901
1
1
1
1
8&
9
16044Z5T901
16100Z5TP72
16124ZE0005
16166Z5T931
16172ZE3W10
16955283000
16211Z5T000
16220ZA0702
16221Z5T000
16212Z5T000
16610ZE1000
16953ZE1812
16954ZE1812
16956ZE1811
16957ZE1812
16967ZE0811
93500030060H
9430520122
CHOKE SET
CARBURETOR ASSY. ( BE94F A) ....................1................INCLUDES ITEMS W/ &
10&
11&
12&
13&
14
15
16
17
18
19&
20&
21&
22&
23&
24&
25#
26&
27&
39&
SCREW, THROTTLE STOP
NOZZLE MAIN
COLLAR SET
1
1
1
PACKING, CUP .................................................1 ...............REPLACES 16173001004
INSULATOR, CARBURETOR
SPACER COMP. CARBURETOR
PACKING, CARBURETOR
PACKING, INSULATOR
CHOKE LEVER COMP. ....................................1................INCLUDES ITEM W/ #
LEVER, COCK
PLATE, LEVER SETTING
SPRING, COCK LEVER
PACKING, FUEL COCK
CUP, FUEL STRAINER
SCREW 3X6
1
1
1
1
1
1
1
1
1
3
1
1
SPRING PIN 2X12
JET, MAIN #92
99101ZH81080
99204ZA00450
16959Z5T901
PILOT JET SET #45 ........................................1................INCLUDES ITEM W/ @
FILTER, CUP
1
MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)— PAGE 69
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX390UT2SMXC — AIR CLEANER ASSY.
13
15
1
5
9
4
11
14
14
2
15
14
14
6
3
12
10
7
7
16
16
PAGE 70 — MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX390UT2SMXC — AIR CLEANER ASSY.
NO.
1
2
3#
4$
5
6#
7$
8$
9
10
11
12
13
14
15
16
PART NO.
PART NAME
PACKING, ELBOW
QTY.
1
REMARKS
16271ZE2010
17210ZE3505
17218ZE3505
17219HA2405
17230ZE3841
17232891000
17238ZE2310
17239ZE3840
17410ZE3841
17470ZE3842
17475ZE3841
17476ZE3841
90009Z1C000
90142MB0000
90325044000
9405006000
ELEMENT, AIR CLEANER ................................1................INCLUDES ITEMS W/ #
FILTER, OUTER
PACKING, AIR CLEANER COVER ...................1................REPLACES 17219ZE3840
COVER CP, AIR CLEANER
GROMMET, AIR CLEANER
COLLAR, AIR CLEANER
COLLAR B, AIR CLEANER
1
1
1
2
1
ELBOW CP, AIR CLEANER ..............................1................INCLUDES ITEMS W/ $
CASE CP, PRE-AIR CLEANER
CAP, PRE-AIR CLEANER
GUIDE, PRE-AIR CLEANER
BOLT, WASHER 6X22
SCREW, PAN 5X16.5
NUT, TOOL BOX SETTING
FLANGE NUT 6MM
1
1
1
1
5
2
2
MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)— PAGE 71
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX390UT2SMXC — MUFFLER ASSY.
19
36
17
37
2
34
19
9
4
18
5
23
6
28
28
28
28
7
PAGE 72 — MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX390UT2SMXC — MUFFLER ASSY.
NO.
2
4
5
6
PART NO.
PART NAME
MUFFLER COMP.
PROTECTOR, EXHAUST PIPE
PIPE, EXHAUST
CAP, MUFFLER
QTY.
1
1
1
1
1
1
1
1
4
3
5
1
1
5
REMARKS
18310Z5T010
18323Z5TW41
18331Z5T000
18331ZE3811
18333Z1C901
18381ZE2W10
90006ZE2000
90013883000
90050ZE1000
90055ZE1000
9405008000
7
9
GASKET EX. PIPE
GASKET, MUFFLER (ARRESTER)
TAPPING SCREW 6X10
FLANGE BOLT 6X12
TAPPING SCREW 5X8
TAPPING SCREW 4X6
FLANGE NUT M8
PROTECTOR COMP., MUFFLER
ARRESTER CP, SPARK
TAPPING SCREW 5X8
17
18
19
23
28
34
36
37
18320Z5T000
18350Z5T800
90050ZE1000
MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)— PAGE 73
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX390UT2SMXC — FUEL TANK ASSY.
18
19
22
4
17
15
12
3
17
1
16
14
16
PAGE 74 — MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX390UT2SMXC — FUEL TANK ASSY.
NO.
1
3
PART NO.
PART NAME
RUBBER, SUPPORT (107MM)
JOINT, FUEL TANK
QTY.
REMARKS
16854ZH8000
16955ZE1010
17510Z5T000ZA TANK CP, FUEL/BLACK
1
1
1
4
12
14
15
16
17
18
19#
22
91353671003
91424Z5T003
9405008000
950024080008
957010802500
17620Z4H900
17631Z0T801
17672Z4H000
O-RING 14MM ..................................................1................REPLACES 91353671004
TUBE, FUEL, 4.5X235 (FKM)
FLANGE NUT M8
CLAMP, TUBE (D8)
1
2
1
2
FLANGE BOLT 8X25
FUEL TANK CAP CP. ........................................1................INCLUDES ITEM W/ #
PACKING, FUEL FILLER CAP
FILTER, FUEL
1
1
MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)— PAGE 75
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX390UT2SMXC — FLYWHEEL ASSY.
1
7
3
4
6
PAGE 76 — MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX390UT2SMXC — FLYWHEEL ASSY.
NO.
1
3
4
6
PART NO.
PART NAME
FAN, COOLING
PULLEY, STARTER
FLYWHEEL COMP.
NUT, SPECIAL 16MM
KEY SPECIAL WOODRUFF 25X18
QTY.
REMARKS
19511ZE3000
28451ZE3W01
31110Z5T000
90201ZE3V00
90741ZE2000
1
1
1
1
1
7
MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)— PAGE 77
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX390UT2SMXC — IGNITION COIL ASSY.
2
10
28
15
4
9
9
PAGE 78 — MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX390UT2SMXC — IGNITION COIL ASSY.
NO.
2
4
PART NO.
PART NAME
CAP ASSY., NOISE SUPPRESOR
GROMMET, CORD
FLANGE BOLT 6X28
CLIP, HARNESS
QTY.
REMARKS
30700ZlC811
31512ZE2000
90015883000
90684ZA0601
32110Z5K000
30500Z5T003
1
1
2
1
1
1
9
10
15
28
HARNESS ASSY. ENGINE WIRE
COIL ASSY. IGNITION
MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)— PAGE 79
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX390UT2SMXC — CONTROL ASSY.
23
17
24
3
1
27
25
26
19
4
9
8
2
14
16
16
7
11
12
13
21
20
10
PAGE 80 — MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX390UT2SMXC — CONTROL ASSY.
NO.
1
2
3
4
7#
PART NO.
PART NAME
ARM, GOVERNOR
ROD, GOVERNOR
SPRING, GOVERNOR
SPRING, THROTTLE RETURN
LEVER CONTROL
LEVER SPRING
WASHER, CONTROL LEVER
HOLDER, CABLE
SPACER, CONTROL LEVER
BASE COMP., CONTROL
ADJUSTING SPRING
SPRING, CABLE RETURN
FLANGE BOLT 6X12
BOLT, GOVERNOR ARM
LOCK NUT 6MM
QTY.
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
REMARKS
16551ZE3000
16555ZE3000
16561ZE3000
16562ZE3000
16571ZE3W00
16574ZE1000
16575ZE2W00
16576891000
16578ZE1000
16580Z5T000
16584883300
16592883310
90013883000
90015Z5T000
90114SA0000
0202005T125
93500050320A
9405006000
8#
9#
10#
11#
12#
13#
14#
16
17
19#
20#
21#
23
SCREW 5X16 ...................................................1................REPLACES 93500050160A
PAN SCREW 5X32
FLANGE NUT 6MM
1
1
24
16500Z5T306
16594883010
90605230000
0043504060
CONTROL ASSY., (REMOTE) ..........................1................INCLUDES ITEMS W/ #
25#
26#
27#
HOLDER, WIRE
CIR CLIP
1
1
SCREW 4X6 .....................................................1................REPLACES 93500040060H
MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)— PAGE 81
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX390UT2SMXC — ENGINE DECAL ASSY.
8
25
4
32
5
14
6
PAGE 82 — MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX390UT2SMXC — ENGINE DECAL ASSY.
NO.
4
5
6
8
14
25
32
PART NO.
PART NAME
QTY.
REMARKS
87528Z5T000
87532ZH7000
89216Z0T800
87535ZE1841
87521Z5T000
87539Z0J000
87516Z4H010
MARK, CHOKE (GRAY)
MARK, THROTTLE INDICATION
WRENCH, SPARK PLUG
MARK, AIR CLEANER
EMBLEM
1
1
1
1
1
1
1
MARK, EX, CAUTION/ENGLISH
MARK, OP-CAUTION/ENGLISH
MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)— PAGE 83
Download from Www.Somanuals.com. All Manuals Search And Download.
TERMS AND CONDITIONS OF SALE — PARTS
5. Parts must be in new and resalable
condition, in the original Multiquip
package (if any), and with Multiquip part
numbers clearly marked.
Multiquip reserves the right to quote and
sell direct to Government agencies, and to
Original Equipment Manufacturer accounts
who use our products as integral parts of their
own products.
PAYMENT TERMS
Terms of payment for parts are net 30 days.
FREIGHT POLICY
6. The following items are not returnable:
All parts orders will be shipped collect or
prepaid with the charges added to the invoice.
All shipments are F.O.B. point of origin.
Multiquip’s responsibility ceases when a
signed manifest has been obtained from the
carrier, and any claim for shortage or damage
must be settled between the consignee and
the carrier.
a. Obsolete parts. (If an item is in the
price book and shows as being
replaced by another item, it is
obsolete.)
SPECIAL EXPEDITING SERVICE
A $35.00 surcharge will be added to the
invoice for special handling including bus
shipments, insured parcel post or in cases
where Multiquip must personally deliver the
parts to the carrier.
b. Any parts with a limited shelf life
(such as gaskets, seals, “O” rings,
and other rubber parts) that were
purchased more than six months
prior to the return date.
LIMITATIONS OF SELLER’S LIABILITY
MINIMUM ORDER
Multiquip shall not be liable hereunder for
damages in excess of the purchase price of
the item with respect to which damages are
claimed, and in no event shall Multiquip be
liable for loss of profit or good will or for any
other special, consequential or incidental
damages.
The minimum charge for orders from Multiquip
is $15.00 net. Customers will be asked for
instructions regarding handling of orders not
meeting this requirement.
c. Any line item with an extended
dealer net price of less than
$5.00.
d. Special order items.
RETURNED GOODS POLICY
e. Electrical components.
f. Paint, chemicals, and lubricants.
g. Decals and paper products.
h. Items purchased in kits.
Return shipments will be accepted and
credit will be allowed, subject to the following
provisions:
LIMITATION OF WARRANTIES
No warranties, express or implied, are
made in connection with the sale of parts or
trade accessories nor as to any engine not
manufactured by Multiquip. Such warranties
made in connection with the sale of new,
complete units are made exclusively by a
statement of warranty packaged with such
units, and Multiquip neither assumes nor
authorizes any person to assume for it
any other obligation or liability whatever in
connection with the sale of its products. Apart
from such written statement of warranty,
there are no warranties, express, implied or
statutory, which extend beyond the description
of the products on the face hereof.
1. A Returned Material Authorization
must be approved by Multiquip prior to
shipment.
7. The sender will be notified of any material
received that is not acceptable.
8. Such material will be held for five
working days from notification, pending
instructions. If a reply is not received
within five days, the material will be
returned to the sender at his expense.
2. To obtain a Return Material Authorization,
a list must be provided to Multiquip
Parts Sales that defines item numbers,
quantities, and descriptions of the items
to be returned.
9. Credit on returned parts will be issued
at dealer net price at time of the original
purchase, less a 15% restocking
charge.
a. The parts numbers and descriptions
must match the current parts price
list.
b. The list must be typed or computer
generated.
10. In cases where an item is accepted, for
which the original purchase document
can not be determined, the price will be
based on the list price that was effective
twelve months prior to the RMA date.
c. The list must state the reason(s)
for the return.
Effective: February 22, 2006
d. The list must reference the sales
order(s) or invoice(s) under
which the items were originally
purchased.
11. Credit issued will be applied to future
purchases only.
PRICING AND REBATES
e. The list must include the name
and phone number of the person
requesting the RMA.
Prices are subject to change without prior
notice. Price changes are effective on a
specific date and all orders received on or
after that date will be billed at the revised price.
Rebates for price declines and added charges
for price increases will not be made for stock
on hand at the time of any price change.
3. AcopyoftheReturnMaterialAuthorization
must accompany the return shipment.
4. Freight is at the sender’s expense. All
parts must be returned freight prepaid to
Multiquip’s designated receiving point.
PAGE 84 — MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)— PAGE 85
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION AND PARTS MANUAL
HERE’S HOW TO GET HELP
PLEASE HAVE THE MODEL AND SERIAL
NUMBER ON-HAND WHEN CALLING
United StateS
Multiquip Corporate Office
MQ Parts Department
18910 Wilmington Ave.
Carson, CA 90746
Contact: [email protected]
Tel. (800) 421-1244
Fax (310) 537-3927
800-427-1244
310-537-3700
Fax: 800-672-7877
Fax: 310-637-3284
Service Department
Warranty Department
800-421-1244
310-537-3700
Fax: 310-537-4259
Fax: 310-943-2238
800-421-1244
310-537-3700
Fax: 310-943-2249
Technical Assistance
800-478-1244
United Kingdom
Canada
Multiquip
Multiquip (UK) Limited Head Office
4110 Industriel Boul.
Laval, Quebec, Canada H7L 6V3
Contact: [email protected]
Tel: (450) 625-2244
Tel: (877) 963-4411
Fax: (450) 625-8664
Unit 2, Northpoint Industrial Estate, Tel: 0161 339 2223
Fax: 0161 339 3226
Globe Lane,
Dukinfield, Cheshire SK16 4UJ
Contact: [email protected]
© COPYRIGHT 2014, MULTIQUIP INC.
Multiquip Inc, the MQ logo and the Mikasa logo are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without written permission. All other trademarks
are the property of their respective owners and used with permission.
This manual MUST accompany the equipment at all times. This manual is considered a permanent part of the equipment and should remain with the unit if resold.
The information and specifications included in this publication were in effect at the time of approval for printing. Illustrations, descriptions, references and technical data contained in
this manual are for guidance only and may not be considered as binding. Multiquip Inc. reserves the right to discontinue or change specifications, design or the information published
in this publication at any time without notice and without incurring any obligations.
Your Local Dealer is:
Download from Www.Somanuals.com. All Manuals Search And Download.
|