OPERATION AND PARTS MANUAL
SERIES
MODEL MVC-64E/EW
PLATE COMPACTOR
(ROBIN GASOLINE ENGINE)
Revision #0 (05/11/06)
To find the latest revision of this
publication, visit our website at:
THIS MANUAL MUST ACCOMPANYTHE EQUIPMENT AT ALLTIMES.
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-64E/EW — PROPOSITION 65WARNING
l
PAGE 2 — MVC-64E/EW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (05/11/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE PAGE
MVC-64E/EW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (05/11/06) — PAGE 3
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-64E/EW —TABLE OF CONTENTS
Multiquip MVC-64E/EW
Plate Compactor
ROBIN EX130D40040
Engine (EPA)
Proposition 65 Warning ............................................. 2
Table Of Contents ..................................................... 4
Parts Ordering Procedures ....................................... 5
Specifications ............................................................ 6
Dimensions ............................................................... 7
Safety Message Alert Symbols .............................. 8-9
Rules For Safe Operation.....................................10-11
Operation and Safety Decals .................................. 12
General Information ................................................ 13
Components (Plate Compactor) ............................. 14
Components (Engine) ............................................. 15
Inspection........................................................... 16-17
Initial Start-Up .................................................... 18-19
Operation ................................................................ 20
Maintenance ...................................................... 21-22
Preparation For Long Term Storage ....................... 23
Troubleshooting (Engine)................................... 24-25
Troubleshooting (Plate Compactor) ........................ 26
Explanation Of Codes In Remarks Column ............ 28
Suggested Spare Parts ........................................... 29
Air Cleaner Assembly.........................................38-39
Camshaft Assembly ...........................................40-41
Carburetor Assembly .........................................42-43
Crankcase Assembly .........................................44-45
Crankshaft and Piston Assembly .......................46-47
Cylinder Head Assembly....................................48-49
Fuel Tank Assembly ...........................................50-51
Governor Assembly ...........................................52-53
Ignition Coil and Flywheel Assembly ................54-55
Muffler Assembly ...............................................56-57
Recoil Starter Assembly.....................................58-59
Terms and Conditions Of Sale — Parts .................. 60
Component Drawings
Specifications and part
numbers are subject to
change without notice.
Name Plate and Decals ..................................... 30-31
Main Body Assembly.......................................... 32-33
Vibrator Assembly .............................................. 34-35
Water Tank ......................................................... 36-37
l
PAGE 4 — MVC-64E/EW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (05/11/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
Effective:June 1st, 2005
PARTS ORDERING PROCEDURES
Ordering parts has never been easier!
Choose from three easy options:
Best Deal!
Order via Internet (Dealers Only)
Orderpartson-lineusingMultiquip’sSmartEquipwebsite!
:
If you have an MQ Account, to obtain a
Username and Password, E-mail us at:
■
■
■
View Parts Diagrams
Order Parts
PrintSpecificationInformation
To obtain an MQ Account, contact your
District Sales Manager for more information.
Use the internet and qualify for a 5% Discount
on Standard orders for all orders which include
complete part numbers.*
to log in and save!
Order Parts
Note: Discounts Are Subject To Change
Fax your order in and qualify for a 3% Discount
on Standard orders for all orders which include
complete part numbers.*
Order via Fax (Dealers Only)
:
All customers are welcome to order parts via Fax.
Domestic (US) Customers dial:
1-800-6-PARTS-7 (800-672-7877)
Note: Discounts Are Subject To Change
Domestic (US) Dealers Call:
1-800-427-1244
Order via Phone:
Non-Dealer Customers:
International Customers should contact
their local Multiquip Representatives for
Parts Ordering information.
Contact your local Multiquip Dealer for
parts or call 800-427-1244 for help in
locating a dealer near you.
When ordering parts, please supply:
❒
❒
❒
❒
❒
❒
Dealer Account Number
❒
Specify Preferred Method of Shipment:
✓
Fed Ex/UPS
✓ DHL
Dealer Name and Address
■
■
Priority One
Ground
✓
Truck
Shipping Address (if different than billing address)
Return Fax Number
■ Next Day
Applicable Model Number
■
Second/ThirdDay
Quantity, Part Number and Description of Each Part
Unless otherwise indicated by customer, all orders are treated asStandard Orders and will ship
within24hours.WewillmakeeveryefforttoshipAirShipmentsthesamedaytheorderisreceived,
if received prior to 2PM PST. Stock Orders must be noted on fax or web order form.
NOTE
WE ACCEPT ALL MAJOR CREDIT CARDS!
MVC-64E/EW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (05/11/06) — PAGE 5
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-64E/EW— SPECIFICATIONS
TABLE 1. COMPACTOR SPECIFICATIONS
Model
MVC-64E/EW
Centrifugal Force
2,275 lbs. (1,032 kg)
Vibration Frequency
5,600 vpm (93 Hz)
Maximum Forward Speed
Plate Size (L x W)
82 ft/min (25 m/min)
21.3 x 13.8 in (541 x 350 mm)
34.6 x 13.8 x 34.9 in (879 x 350 x 886 mm)
165 lbs. (75 kg)
Overall Dimensions (L x W x H)
Operating Weight (with water tank)
Operating Weight (without water tank)
Maximum Area of Compaction
143 lbs. (65 kg)
5,658 sq. ft/hr (526 sq. m/hr)
Table 2. ENGINE SPECIFICATIONS
Model
ROBIN EX130D40040
Air-cooled 4 stroke, Single
Cylinder, Overhead
Type
Camshaft Gasoline Engine
Displacement
Max Output
126 cc.
4.3 H.P./4,000 R.P.M.
3.0 H.P./3,600 R.P.M.
Continuous Output
Engine
Approx. .71 U.S. gallons
(2.7 liters)
l
Fuel Tank Capacity
Unleaded Automobile
Gasoline
Fuel
Lube Oil Capacity
Spark Plug
.634 qts. (0.6 liters)
NGK BR-6HS
(Champion RL86C)
11.69 x 13.4 x 12.5 in.
(297 x 341 x 318 mm)
Dimension
(L x W x H)
Dry
Net Weight
31 lbs. (14 Kg.)
PAGE 6 — MVC-64E/EW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (05/11/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-64E/EW— DIMENSIONS
Figure 1. MVC-64E/EW Plate Compactor Dimensions
TABLE 3. DIMENSIONS
DESCRIPTION
REFERENCE LETTER
DIMENSION In. (mm)
36 In. (914 mm)
13 In. (330 mm)
25 In. (635 mm)
21 In. (533 mm)
36 In. (914 mm)
25 In. (635 mm)
Height (Handle Upright)
A
B
C
D
E
F
Width
Length (Handle Upright)
Plate Length
Length (Handle Lowered)
Height (Compactor Only)
27 x 15 x 28 In.
(686 x 381 x 711)
Shipping Dimensions
MVC-64E/EW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (05/11/06) — PAGE 7
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-64E/EW— SAFETY MESSAGE ALERT SYMBOLS
Potential hazards associated with the operation of an
MVC-64E/EW Plate Compactor will be referenced with
FORYOUR SAFETY ANDTHE SAFETY OF OTHERS!
Safety precautions should be followed
at all times when operating this
equipment. Failure to read and
understand the Safety Messages and
Operating Instructions could result in
injury to yourself and others.
Hazard Symbols which appear throughout this manual, and
Lethal Exhaust Gases
will be referenced in conjunction with Safety Message Alert
Symbols.
Lethal Exhaust Gases
HAZARD SYMBOLS
WARNING - Lethal Exhaust Gasses
This Owner's Manual has been
developed to provide complete
instructions for the safe and
efficient operation of the
Multiquip Plate Compactor
MVC-64E/EW. Refer to the
Engine exhaust gases contain
poisonous carbon monoxide. This gas
is colorless and odorless, and can
cause death if inhaled. NEVER operate
this equipment in a confined area or
enclosed structure that does not provide
ample free flow air.
engine manufacturer's instructions for data relative to its
safe operation.
Before using this plate compactor, ensure that the
operating individual has read and understands all
instructions in this manual.
WARNING - Explosive Fuel
Gasoline is extremely flammable, and its
vapors can cause an explosion if ignited.
DO NOT start the engine near spilled fuel
or combustible fluids.
SAFETY MESSAGE ALERT SYMBOLS
DO NOT fill the fuel tank while the engine is running or
hot. DO NOT overfill tank, since spilled fuel could ignite if
it comes into contact with hot engine parts or sparks from
the ignition system. Store fuel in approved containers, in
well-ventilated areas and away from sparks and flames.
The three (3) Safety Messages shown below will inform you
about potential hazards that could injure you or others. The
Safety Messages specifically address the level of exposure
to the operator, and are preceded by one of three words:
DANGER, WARNING, or CAUTION.
DANGER
WARNING - Burn Hazards
Engine components can generate extreme
heat. To prevent burns, DO NOT touch
these areas while the engine is running or
immediately after operations. Never
operate the engine with heat shields or heat
guards removed.
You WILL be KILLED or SERIOUSLY injured if you DO
l
NOT follow directions.
WARNING
You CAN be KILLED or SERIOUSLY injured if you DO
NOT follow directions.
CAUTION - Respiratory Hazard
CAUTION
ALWAYS wear approved respiratory
protection when required.
You CAN be INJURED if you DO NOT follow directions.
PAGE 8 — MVC-64E/EW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (05/11/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-64E/EW— SAFETY MESSAGE ALERT SYMBOLS
CAUTION - Rotating Parts
CAUTION - Equipment Damage Messages
NEVER operate equipment with covers,
or guards removed. Keep fingers, hands,
hair and clothing away from all moving
parts to prevent injury.
Other important messages are provided throughout this
manual to help prevent damage to your plate compactor,
other property, or the surrounding environment.
CAUTION - Accidental Starting
ALWAYS place the power source, circuit
breakers or ON/OFF switch in the OFF
position, when the compactor is not in
use.
This plate compactor, other
property, or the surrounding
environment could be damaged
if you do not follow instructions.
CAUTION - Sight and Hearing Hazards
ALWAYS wear approved eye and
hearing protection.
MVC-64E/EW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (05/11/06) — PAGE 9
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-64E/EW — RULES FOR SAFE OPERATION
■
■
■
NEVER touch the hot exhaust
manifold, muffler or cylinder. Allow
these parts to cool before servicing
engine or mixer.
CAUTION - Read Manual!
Failure to follow instructions in this
manual may lead to serious injury or
even death! This equipment is to be
operated by trained and qualified
personnel only! This equipment is for
industrial use only.
High Temperatures – Allow the
engine to cool before adding fuel or
performing service and maintenance functions. Contact
with hot! components can cause serious burns.
The engine section of this mixer requires an adequate
free flow of cooling air. NEVER operate the compactor
in any enclosed or narrow
The following safety guidelines should always be used when
operating the MQ Mikasa Model MVC-64E/EW Plate
Compactor.
area where free flow of the
GENERAL SAFETY
air is restricted. If the air
flow is restricted it will
cause serious damage to
the compactor or engine
and may cause injury to
people. Remember the
plate compactor's engine
gives off DEADLY carbon monoxide gas.
■
■
■
DO NOT operate or service this equipment before reading
this entire manual.
This equipment should not be operated by persons under
18 years of age.
NEVER operate this equipment without proper protective
clothing, shatterproof glasses, steel-toed boots and other
protective devices required by the job.
■
■
ALWAYS refuel in a well-ventilated area, away from sparks
and open flames.
ALWAYS use extreme caution when
working with flammable liquids. When
refueling, stop the engine and allow it to
cool. DO NOT smoke around or near the
machine. Fire or explosion could result
from fuel vapors, or if fuel is spilled on a
hot engine.
■
■
NEVER operate this equipment when not
feeling well due to fatigue, illness or taking
medicine.
NEVER operate this equipment under the
influence of drugs or alcohol.
■
■
NEVER operate the plate compactor in
an explosive atmosphere or near
combustible materials. An explosion or
fire could result causing severe bodily
harm or even death.
Topping-off to filler port is dangerous, as it tends to spill
fuel.
■
■
Maintain this equipment in a safe operating condition at
all times.
ALWAYS store equipment properly when it is not being
used. Equipment should be stored in a clean, dry location
out of the reach of children.
PAGE 10 — MVC-64E/EW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (05/11/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-64E/EW— RULES FOR SAFE OPERATION
■
■
■
NEVER run engine without air filter. Severe engine damage
TRANSPORTING
may occur.
■
■
ALWAYS shutdown engine before transporting.
Tighten fuel tank cap securely and close fuel cock to
prevent fuel from spilling.
ALWAYS service air cleaner frequently to prevent carburetor
malfunction.
ALWAYS be sure the operator is familiar with proper safety
precautions and operations techniques before using
compactor.
■
Drain fuel when transporting compactor over long
distances or bad roads.
MAINTENANCE
■
■
ALWAYS read, understand, and follow procedures in
Operator’s Manual before attempting to operate equipment.
■
NEVER lubricate components or attempt service on a
running compactor.
Refer to the Robin Engine Owner's Manual for engine
technical questions or information.
■
ALWAYS allow the plate compactor a proper amount of
time to cool before servicing.
■
■
Keep the compactor in proper running condition.
Fix damage to the plate compactor immediately and
always replace broken parts.
Dispose of hazardous waste properly. Examples of
potentially hazardous waste are used motor oil, fuel and
fuel filters.
Loading and Unloading (Crane)
■
Before lifting, make sure that machine parts (lifting bale and
vibration insulator) are not damaged and screws are not
loosened or lost.
■
■
■
ALWAYS make sure crane or lifting device has been properly
secured to the lifting bale on the compactor.
DO NOT use food or plastic containers to dispose of
hazardous waste.
EMERGENCIES
■
ALWAYS know the location of the nearest fire
extinguisher and first aid kit.
■
In emergencies always know the location of the
nearest phone or keep a phone on the job site.
Also know the phone numbers of the nearest
ambulance, doctor and fire department. This
information will be invaluable in the case of an
emergency.
■
■
■
■
NEVER lift the compactor while the engine is running.
Use adequate lifting cable (wire or rope) of sufficient strength.
Use one point suspension hook and lift straight upwards.
NEVER allow any person or animal to stand underneath the
machine while lifting.
■
Try not to lift compactor to unnecessary heights.
MVC-64E/EW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (05/11/06) — PAGE 11
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-64E/EW— OPERATION AND SAFETY DECALS
Machine Safety Decals
The MVC-64E/EW Plate Compactor is equipped with a number of safety decals.These decals are provided for operator safety and
maintenance information.The illustration below shows these decals as they appear on the machine. Should any of these decals
become unreadable, replacements can be obtained from your dealer.
CAUTION !
"
"
"
READ OWNER’S SERVICE MANUAL BEFORE OPERATING OR
SERVICING THIS MACHINE.
ALWAYS KEEP UNAUTHORIZED, INEXPERIENCED,
UNTRAINED PEOPLE AWAY FROM THIS MACHINE.
MAKE SURE ALL SAFETY DEVICES ARE OPERATIONAL
BEFORE THIS MACHINE IS STARTED. BE SURE ENGINE
IS TURNED OFF AND SPARK PLUGS ARE DISCONNECTED
BEFORE SERVICING THE MACHINE OR COMING IN
CONTACT WITH ANY MOVING PART. IF EQUIPMENT IS
POWERED BY AN ELECTRIC MOTOR, DISCONNECT
ELECTRICAL PLUG.
"
NEVER LEAVE MACHINE UNATTENDED WHEN OPERATING.
ALWAYS STOP ENGINE AND ALLOW ENGINE TO COOL
BEFORE ADDING FUEL OR OIL.
NPA-329
*
P/N: 920203290
Serial No.
Model No.
NPA-989
*
CONTACT
PARTS DEPT.
P/N 9202039890
Figure 2. Operation and Safety Decals
l
PAGE 12 — MVC-64E/EW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (05/11/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-64E/EW — GENERAL INFORMATION
Definition of Plate Compactor
Frequency/Speed
The Mikasa MVC-64E/EW is a walk-behind, plate compactor
designed for the compaction of sand, mixed soils and asphalt.
This plate compactor is a powerful compacting tool capable of
applying a tremendous force in consecutive high frequency
vibrations to a soil surface. Its applications include compacting
for road, embankments and reservoirs as well as backfilling for
gas pipelines, water pipelines and cable installation work.
The compactor's vibrating plate has a frequency of 5,600 vpm
(vibrations per minute). The travel speed of the compactor is
approximately 82 ft./minute (25 meters/minute).
Engine
The Mikasa MVC-64E/EW Plate Compactor is equipped with a
ROBIN EX130D40040 gasoline engine.
Controls
The MVC-64E/W is small and lightweight. It can be easily
handled by one person in confined areas. It has an accessible
front-mounted vibrator assembly.The sealed belt cover keeps
dirt and rocks away from the belt.
Before starting the MVC-64E/EW Plate Compactor identify and
understand the function of the controls and components as
indicated Figure 3.
Vibratory Plate
WARNING
The vibratory plate of the compactor produces low amplitude
high frequency vibrations, designed to compact granular soils
and asphalt.
To avoid injuries and damage to the equipment, ALWAYS
read and understand contents of operation manual before
operating equipment.
The resulting vibrations cause forward motion.The engine and
handle are vibration isolated from the vibrating plate.
MVC-64E/EW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (05/11/06) — PAGE 13
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-64E/EW — COMPONENTS (PLATE COMPACTOR)
Figure 3. MVC-64E/EW Plate Compactor Components
6. Belt Cover – Remove this cover to gain access to the V-
belts.NEVER run the compactor without theV-belt cover.If
the V-belt cover is not installed, the possibility exist that
your hand may get caught between the V-belt and clutch,
thus causing serious injury and bodily harm.
Figure 3 shows the location of the components and general
maintenance parts. The function of each component is described
below:
1. Water Tank Cap (for MVC-64EW only) – Remove this
l
cap to add water to the water tank.
7. Vibrating Plate – A flat, open plate made of durable cast
2. FuelTank Cap – Remove this cap to add fuel.
iron construction used in the compacting of soil.
3.
Lifting Bail – When lifting of the compactor is required
either by forklift, crane etc., tie rope or chain around this
lifting point.
8. Vibration Case – Encloses the eccentric, gears and
counter weights.
9. Water Shut-OffValve (for MVC-64EW only) – Turn this
valve downward to let water flow from the water tank to the
water tube.
4. Handle Bar – When operating the compactor use this
handle bar to maneuver the compactor.
5. Gasoline Engine – This plate compactor uses a ROBIN
EX130D40040 ROBIN engine. Refer to the ROBIN owner's
manual for engine information.
10. WaterTank (for MVC-64EW only) – Holds 10.6 quarts
(10 liters) of water, removable no tools required.
PAGE 14 — MVC-64E/EW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (05/11/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-64E/EW— COMPONENTS (ENGINE)
Figure 4. Engine Controls and Components
INITIAL SERVICING
5. Throttle Lever – Used to adjust engine RPM speed (lever
advanced forward SLOW, lever back toward operator
FAST).
The engine (Figure 4) must be checked for proper lubrication and
filled with fuel prior to operation. Refer to the ROBIN engine service
manualforinstructions anddetailsforproperoperationandservicing.
6. Recoil Starter (pull rope) – Manual-starting method. Pull
the starter grip until resistance is felt, then pull briskly and
smoothly.
1. Muffler – Used to reduce noise and emissions.
WARNING
7. Choke Lever – Used in the starting of a cold engine, or in
cold weather conditions. The choke enriches the fuel
mixture.
Engine components can generate extreme heat.
To prevent burns, DO NOT touch these areas
while the engine is running or immediately after operating. NEVER
operate the engine with the muffler removed.
8. FuelValve Lever – OPEN to let fuel flow, CLOSE to stop
the flow of fuel.
9. Spark Plug – Provides spark to the ignition system. Set
spark plug gap to 0.6 - 0.7 mm (0.028 - 0.031 inch) Clean
spark plug once a week.
2. Air Cleaner – Prevents dirt and other debris from entering
the fuel system. Remove wing-nut on top of air filter
cannister to gain access to filter element.
10. Engine ON/OFF Switch – ON position permits engine
3. Fuel Tank – Holds unleaded gasoline. For additional
starting, OFF position stops engine operations.
information refer to ROBIN engine owner's manual.
11. Oil Drain Plug – Remove this plug to drain engine oil from
4. Fuel Filler Cap – Remove this cap to add unleaded
gasoline to the fuel tank. Make sure cap is tightened
securely. DO NOT over fill.
the crankcase.
12. Oil Dipstick/ Filler Cap– Remove the filler cap dipstick
when checking the engine oil level. Add engine oil through
this filler port. See Table 5 for recommended type engine
oil.
DANGER
Adding fuel to the tank should be done only when
the engine is stopped and has had an opportunity to
cool down. In the event of a fuel spill, DO NOT attempt to start the
engine until the fuel residue has been completely wiped up, and the
area surrounding the engine is dry.
Operating the engine without an air
filter, with a damaged air filter, or a
filter in need of replacement will
allow dirt to enter the engine,
causing rapid engine wear.
MVC-64E/EW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (05/11/06) — PAGE 15
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-64E/EW — INSPECTION
The Oil Alert system will
automatically stop the engine
before the engine falls below safe
limits. Always be sure to check
the engine oil level prior to starting
the engine.
Before Starting
1. Read safety instructions at the beginning of manual.
2. Cleanthecompactor,removingdirtanddust.Particularly,the
bottom of the plate, engine cooling air inlet, carburetor and
aircleaner.
3. Checktheairfilterfordirtanddust.Iftheairfilterisdirty,blow
throughtheairfiltercartridgefromtheinside,movingajetof
dry compressed air up and down until all dust is removed.
Otherwise replace air filter with a new one.
Table 4. Oil Type
Season
Summer
Spring/Fall
Winter
Temperature
Oil Type
SAE 10W-30
SAE 10W-30/20
SAE 10W-10
25°C or Higher
25°C~10°C
4. Check carburetor for external dirt and dust. Clean with dry
compressedair.
5. Check fastening nuts and bolts for tightness. Loosened
screws or bolts due to vibration, could lead to unexpected
accident.
0°C or Lower
Gasoline Check
Engine Oil Check
1. Remove the gasoline cap located on top of fuel tank.
1. To check the engine oil level, place the plate compactor on
secure level ground with the engine stopped.
2. Visuallyinspecttoseeiffuellevelislow. Iffuelislow,replenish
with unleaded fuel.
2. Remove the filler cap/dipstick from the engine oil filler hole
(Figure 5) and wipe it clean.
3. When refueling, be sure to use a strainer for filtration. DO
NOT top-off fuel. Wipe up any spilled fuel.
Vibrator Oil Check
1. PlacetheMVC-64E/Wplatecompactorhorizontallyonaflat
surface.Makesurethecompactorislevelwhencheckingthe
oil in the vibrator assembly.
2. Check vibratoroillevelbyremoving theplug (vibrator oilgauge)
asshowninFigure7. Theoillevelshouldbeuptotheoilplug.
If oil is required, replace using only SAE 10W-30 motor oil.
Figure 5. EnginelOil Dipstick
3. Insertandremovethedipstickwithoutscrewingitintothefiller
neck. Check the oil level shown on the dipstick.
4. If the oil level is low (Figure 6), fill to the edge of the oil filler
hole with the recommended oil type (Table 4).
UPPER LIMIT
Figure 7.Vibrator Oil Plug
LOWER LIMIT
Figure 6. Engine Oil Dipstick
PAGE 16 — MVC-64E/EW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (05/11/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-64E/EW — INSPECTION
2. TheV-belt tension is proper if theV-belt bends 10 to 15 mm
(Figure 10) when depressed with finger at midway between
the clutch and vibration pulley shafts.
V-Belt Check
CAUTION
NEVER attempt to check theV-belt with the engine running.
Severe injury can occur of your hand (Figure 8) gets caught
betweentheV-beltandtheclutch.Alwaysusesafetygloves.
CLUTCH
PULLEY
Figure 10.V-BeltTension
3. A looseV-belt will decrease the power transmission output,
causing reduced compaction and premature wear of the
belt.
VIBRATOR
PULLEY
4. If theV-belt becomes worn or loose, replace it .
Figure 8.V-Belt Hazard
1. Tocheck theV-belttension,removethe boltsthatsecurethe
belt cover to the frame as shown in Figure 9.
Figure 9.V-Belt Cover Removal
MVC-64E/EW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (05/11/06) — PAGE 17
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-64E/EW — INITIAL START-UP
3. Placethechokelever(Figure13)inthe"CLOSED"position
if starting a cold engine.
CAUTION
DO NOT attempt to operate the
equipment until the Safety, General
Information and Inspection sections of
this manual have been read and
thoroughly understood.
This section is intended to assist the operator with the initial
start-up of the equipment. It is extremely important that this
section be read carefully before attempting to use the equipment
in the field.
Figure 13. Engine Choke Lever (Closed)
Starting the Engine
1. Place the engine fuel valve lever (Figure 11) to the "ON"
position.
4. Place the choke lever (Figure 14) in the "OPEN " position
if starting a warm engine or the temperature is warm.
Figure 11. Engine Fuel Valve Lever (ON Position)
2. Move the throttle lever (Figure 12) away from the slow
position, about 1/3 of the way toward the fast position.
Figure 14. Engine Choke Lever (Open)
5. Place the engine ON/OFF switch (Figure 15) in the "ON "
position.
Figure 12. Throttle Lever (1/3 Start Position)
Figure 15. Engine ON/OFF Switch (ON Position)
PAGE 18 — MVC-64E/EW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (05/11/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-64E/EW— INITIAL START-UP
6. Grasp the starter grip (Figure 16) and slowly pull it out.The
resistancebecomesthehardestatacertainposition,corre-
spondingtothecompressionpoint.Pullthestartergripbriskly
andsmoothlyforstarting.
CAUTION
ALWAYS run engine at full speed while operating
equipment.
Stopping The Engine
Normal Shutdown
1. Movethethrottlelever tothe IDLEposition (Figure19)and
run the engine for three minutes at low speed.
Figure 16. Starter Grip
7. If the engine has started, slowly return the choke lever
(Figure 17) to the “OPEN” position. If the engine has not
started repeat steps 1 through 6.
Figure 19.Throttle Lever (Idle)
2. Aftertheenginecools,turntheengineON/OFFswitchtothe
“OFF” position (Figure 20).
Figure 17. Choke Lever (Open)
8. Beforetheequipmentisplacedintooperation,runtheengine
for several minutes. Check for fuel leaks, and noises that
would associate with a lose component.
Figure 20. Engine ON/OFF Switch (OFF)
3. Place the fuel shut-off lever (Figure 21) in the OFF
9. To begin operation, place the throttle lever (Figure 18) in the
position.
"RUN" position.
Figure 21. Fuel Valve Lever (OFF)
Emergency Shutdown
1. MovethethrottleleverquicklytotheIDLE position,andplace
the engine ON/OFF switch in the OFF position.
Figure 18. Throttle Lever (Run)
MVC-64E/EW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (05/11/06) — PAGE 19
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-64E/EW— OPERATION
Operation
CAUTION
5. Compactortravelingspeedmaydroponsoilswhichcontain
clay, however there may be cases where traveling speed
drops because the compaction plate does not leave the
ground surface easily due to the composition of the soil.To
rectify this problem do the following:
Make sure to follow all safety rules referenced in the safety
section of this manual before operating compactor. Keep
workareaclearofdebrisandotherobjectsthatcouldcause
damage to the compactor or bodily injury.
z
z
z
Check the bottom plate to see if clay or
equivalent material has been lodged in the plate
mechanism. If so, wash with water and remove.
Remember the compactor does not work as
efficiently on clay or soils that have a high
moisture content level.
1. Oncetheenginehasstarted, movetheenginethrottlelever
quickly to the fastposition.
2. With the throttle lever in the fast position, the engine speed
should be around 2,300 RPM, therefore engaging the cen-
trifugalclutch.
If the soil has a high moisture level, dry soil to
appropriate moisture content level or carry out
compaction twice.
Always move the throttle lever
quickly without hesitation, because
increasing the engine speed slowly
causes the clutch to slip.
3. Firmlygaspthecompactor'shandlebar withbothhands,the
compactor will begin moving forward.
4. Slowlywalkbehindthecompactorandbeonthelookout for
anylargeobjectsorforeignmatterthatmightcausedamage
to the compactor or bodily injury.
l
PAGE 20 — MVC-64E/EW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (05/11/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-64E/EW — MAINTENANCE
CAUTION
CAUTION
These inspection intervals are for operation under normal
conditions. Adjust your inspection intervals based on the
number hours plate compactor is in use, and particular
working conditions.
Inspection and other services should always be carried out
on hard and level ground with the engine shut down.
Inspection and Maintenance ServiceTables.
1. To make sure your plate compactor is always in good
working condition before using, carry out the maintenance
inspection in accordance with Tables 5 through 7.
CAUTION
Fuel piping and connections should be replaced every 2
years.
TABLE 5. MVH-64E/EW MACHINE INSPECTION
Daily Service
ITEM
HOURS OF OPERATION
Every 8 hours (every day)
Every 8 hours (every day)
z
Check for leakage of fuel or oil.
Damaged Parts
Loose or Lost Screws
z
Remove soil and clean the bottom of compaction plate.
Check engine oil, see page 16.
z
z
Check for loose screws including tightness. See Table 7
below (tightening torque ), for retightening:
Function of Controlling System
Part
Every 8 hours (every day)
TABLE 7.
Vibrator Oil Check
Every 100 hours
Every 300 hours
Every 200 hours
TIGHTENING TORQUE (in. kg/cm) Diameter
Vibrator Oil Replacement
V-belt (clutch) Check
Material 6mm 8mm 10mm 12mm 14mm 16mm 18mm 20mm
4T
6-8T
11T
*
70
150
250
400
300
500
800
500
750
1,100 1,400 2,000
2,000 2,700 3,800
100
150
800
1,300
1,200
2,000 2,900 4,200 5,600
Table 6. ENGINE MAINTENANCE
100 (6mm) 300 ~ 350 (8mm) 650 ~ 700 (10mm)
FIRST
MONTH
OR
EVERY
MONTHS
OR
3
EVERY
MONTHS
OR
6
EVERY
YEAR
OR
EVERY
2 YEARS
OR
* (In case counter-part is of aluminum)
DESCRIPTION (3)
OPERATION
BEFORE
10 HRS.
25 HRS.
50 HRS.
100 HRS.
200 HRS.
(Threads in use with this machine are all right handed)
CHECK
CHANGE
CHECK
X
Engine Oil
X
Material and quality of material is marked on each bolt,
and screw.
X
X
Air Cleaner
All Nuts & Bolts
Spark Plug
CHANGE
X (1)
Re-tighten If
Necessary
ENGINEOIL
CHECK-CLEAN
REPLACE
CHECK
X
X
1. Drain the engine oil when the oil is warm as shown in
X
Figure 22.
Cooling Fins
Spark Arrester
Fuel Tank
CLEAN
X
X
2. Remove the oil drain bolt and sealing washer and allow
the oil to drain into a suitable container.
CLEAN
Fuel Filter
CHECK
X
Idle Speed
CHECK-ADJUST
CHECK-ADJUST
CHECK
X (2)
3. Replace engine oil with recommended type oil as listed
inTable 4.Engine oil capacity is .634 quarts (.6 liters).DO
NOT overfill.
Valve Clearance
Fuel lines
X (2)
Every 2 years (replace if necessary) (2)
(1) Service more frequently when used in DUSTY areas.
(2) These items should be serviced by your servic dealer, unless you have the proper tools and are mechanically
proficient. Refer to the ROBIN Manual for service procedures
4. Install drain bolt with sealing washer and tighten se-
curely.
(3) For commercial use, log hours of operation to determine proper maintenance intervals.
MVC-64E/EW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (05/11/06) — PAGE 21
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-64E/EW — MAINTENANCE
Changing Vibrator Oil
1. When changing the vibrator oil, remove the drain plug
(Figure 7), and simply tip the compactor to drain the oil.
Note that the oil will drain more easily while it is hot.
Remember to use only 10W-30 motor oil when replacing
vibrator oil.
Checking and Replacing the V-Belt and Clutch
1. After 200 hours of operation, remove the upper belt cover to
check theV-belt tension.Tension is proper if the belt bends
about 10 mm when depressed strongly with finger between
shafts. Loose or worn V-belts reduces power transmission
efficiency, causing weak compaction and reduces the life of
the belt itself.
Figure 22. Engine Oil (Draining)
Spark Plug
1. Remove and clean the spark plug (Figure 23).
2. Adjust the spark gap to 0.028 ~0.031 inch (0.6~0.7 mm).This
unit has electronic ignition, which requires no adjustments.
CAUTION
NEVERattempttochecktheV-beltwiththeenginerunning.
Severeinjurycanoccurifyourhand(Figure 8)getscaught
betweentheV-beltandtheclutch.Alwaysusesafetygloves.
CAUTION
Wheneverthecompactor'svibrationbecomesweakorlost
during normal operation regardless of operation hours,
check theV-belt and clutch immediately.
Figure 23. Spark Plug Gap
Engine Air Cleaner
z
Replacing the V-belt
1. Remove the air cleaner cover and foam filter element as
shown in Figure 24.
Remove the upper and lower belt covers. Engage an offset
wrench (13 mm) or the like to vibrator pulley (lower) fastening
bolt. Engage waste cloth or the like at midway ofV-belt on the left
side and while pulling it back strongly, rotate the offset wrench
clockwise so that theV-belt will come off.
2. Wash the foam filter element in kerosene or diesel fuel.
Then saturate it in a mixture of 3 parts kerosene or diesel
fuel and 1 part engine oil. Completely squeeze the ele-
l
ment to remove the mixture and reinstall it back into the
air cleaner.
z
Reinstalling the V-belt
EngageV-belt to lower vibrator pulley and push theV-belt to left
side of upper clutch and, in the same manner as in removal,
rotate offset wrench clockwise so that the V-belt goes back on.
z
Checking Clutch
Check the clutch simultaneously withV-belt checking. With belt
removed, check outer drum of the clutch for seizure and "V"
groove for wear or damage with your eyes. Clean the "V" groove
as necessary. Wear of lining or shoe should be checked with
running check. If the shoe is worn, power transmission becomes
deficient and slipping will result.
Figure 24. Air Cleaner
PAGE 22 — MVC-64E/EW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (05/11/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-64E/EW— PREPARATION FOR LONG -TERM STORAGE
Compactor Storage
For storage of the compactor for over 30 days, the following
is required:
z
z
Drain the fuel tank completely.
Run the engine until the fuel in the injection system is
completely consumed.
z
Completely drain the oil from the engine crankcase and
follow procedures described in the ROBIN engine
Owner's Manual for engine storage.
z
z
z
Completely drain the compactor's oil from the vibrating
case.
Clean entire plate compactor, especially the bottom plate
removing all dirt and foreign matter.
Cover plate compactor and engine with plastic covering
or equivalent and store in a clean, dry place.
MVC-64E/EW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (05/11/06) — PAGE 23
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-64E/EW — TROUBLESHOOTING (ENGINE)
Practically all breakdowns can be prevented by proper handling and maintenance inspections, but in the event of a
breakdown, please take a remedial action following the diagnosis based on the EngineTroubleshooting (Table 8) information
shown below and on the proceeding page. If the problem cannot be remedied, please leave the unit just as it is and consult
our company's business office or service plant.
TABLE 8. ENGINE TROUBLESHOOTING
SYMPTOM
POSSIBLE CAUSE
SOLUTION
Check gap, insulation or replace
spark plug.
Spark plug bridging?
Carbon deposit on spark plug?
Clean or replace spark plug.
Difficult to start, "fuel is available, but no
SPARK at spark plug".
Short circuit due to deficient spark plug
insulation?
Check spark plug insulation,
replace if worn.
Improper spark plug gap?
ON/OFF switch is shorted?
Ignition coil defective?
Set to proper gap.
Check switch wiring, replace
switch.
Replace ignition coil.
Set correct spark gap and clean
points.
Difficult to start, "fuel is available, and
SPARK is present at the spark plug".
Improper spark gap, points dirtry?
Condenser insulation worn or short
circuiting?
Replace condenser.
Replace defective spark plug
wiring.
Spark plug wire broken or short circuiting?
Wrong fuel type?
Flush fuel system, and replace
with correct type of fuel.
Difficult to start, "fuel is available, spark
is present and compression is normal"
Water or dust in fuel system?
Air cleaner dirty?
Flush fuel system.
Clean or replace air cleaner.
Re-seat valves.
Suction/exhaust valve stuck or protruded?
Replace piston rings and or
piston.
l
Piston ring and/or cylinder worn?
Difficult to start, "fuel is available, spark
is present and compression is low"
Cylinder head and/or spark plug not
tightened properly?
Torque cylinder head bolts and
spark plug.
Head gasket and/or spark plug gasket
damaged?
Replace head and spark plug
gaskets.
Fuel not available in fuel tank?
Fill with correct type of fuel.
Apply lubricant to loosen fuel
cock lever, replace if necessary.
Fuel cock does not open properly?
No fuel present at carburetor.
Fuel filter clogged?
Replace fuel filter.
Fuel tank cap breather hole clogged?
Air in fuel line?
Clean or replace fuel tank cap.
Bleed fuel line.
PAGE 24 — MVC-64E/EW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (05/11/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-64E/EW — TROUBLESHOOTING (ENGINE)
TABLE 8. ENGINE TROUBLESHOOTING (CONTINUED)
SYMPTOM
POSSIBLE CAUSE
Air cleaner not clean?
SOLUTION
Clean or replace air cleaner
Check float adjustment, re-build
carbureator.
Improper level in carburetor?
"Weak in power" compression is proper
and does not misfire.
Defective Spark plug?
Defective Spark plug?
Clean or replace spark plug.
Flush fuel system, and replace
with correct type of fuel.
Water in fuel system?
"Weak in power" compression is proper
but misfires.
Dirty spark plug?
Clean or replace spark plug.
Replace ignition coil.
Ignition coil defective?
Replace with correct type of
spark plug.
Spark plug heat value improper?
Engine overheats.
Correct type of fuel?
Replace with correct type of fuel
Clean cooling fins.
Cooling fins dirty?
Governor adjusted correctly?
Governor spring defective?
Adjust governor.
Replace governor spring.
Rotational speed fluctuates.
Recoil starter malfunction.
Check entire fuel system for leaks
or clogs.
Fuel flow restricted?
Recoil mechanism clogged with dust and Clean recoil assembly with soap
dirt?
and water.
Sprial spring loose?
Replace sprial spring.
MVC-64E/EW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (05/11/06) — PAGE 25
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-64E/EW — TROUBLESHOOTING (PLATE COMPACTOR)
Practically all breakdowns can be prevented by proper handling and maintenance inspections, but in the event of a
breakdown, please take a remedial action following the diagnosis based on the Compactor Troubleshooting (Table 9)
information shown below and on the proceeding page. If the problem cannot be remedied, please leave the unit just as it is
and consult our company's business office or service plant.
TABLE 9. PLATE COMPACTOR TROUBLESHOOTING
SYMPTOM
POSSIBLE CAUSE
Engine speed too low?
SOLUTION
Set engine speed to correct RPM.
Check or replace clutch.
Clutch slips?
Travel speed too low, and vibration is
weak.
V-belt slips?
Adjust or replace V-belt.
Excessive oil in vibrator?
Drain excess oil and fill to proper level.
Check eccentric, gears and counter
weights.
Malfunction in vibrator housing?
V-belt slips?
Clutch slips?
Replace V-belt.
Check clutch springs and shoes.
Does not travel forward.
Check vibrator housing (eccentric,
gears and counterweights)
Vibrator locked?
l
PAGE 26 — MVC-64E/EW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (05/11/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE PAGE
MVC-64E/EW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (05/11/06) — PAGE 27
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-64E/EW— EXPLANATION OF CODES IN REMARKS COLUMN
How to read the marks and remarks used in this parts book.
If more than one of the same
reference number is listed, the last
one listed indicates newest (or latest)
part available.
Items Found In the “Remarks” Column
Serial Numbers-Where indicated, this indicates a serial
number range (inclusive) where a particular part is used.
Model Number-Where indicated, this shows that the
corresponding part is utilized only with this specific model
number or model number variant.
The contents of this catalog are
subject to change without notice.
Items Found In the “Items Number” Column
All parts with same symbol in the number column, , #,
+
, %, or
*
>
, belong to the same assembly or kit.
l
PAGE 28 — MVC-64E/EW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (05/11/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-64E/EW— SUGGESTED SPARE PARTS
MQ MIKASA MVC-64E/EW PLATE COMPACTOR WITH
ROBIN EX130D40040 GASOLINE ENGINE
1 to 3 Units
Qty.
P/N
Description
3 .......... 070100312 ........... V-BELT
4 .......... 939010214 ........... SHOCK ABSORBER
3 .......... 0650140150 ......... SPARK PLUG
1 .......... 0430430060 ......... FUEL CAP
1 .......... 5825011118 ......... STARTER ROPE
3 .......... 2773261107 ......... ELEMENT, AIR FILTER
1 .......... 0641360010 ......... FUEL FILTER
MVC-64E/EW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (05/11/06) — PAGE 29
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-64E/EW— NAME PLATE AND DECALS
NAME PLATE AND DECALS
l
PAGE 30 — MVC-64E/EW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (05/11/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-64E/EW— NAME PLATE AND DECALS
NAMEPLATE AND DECALS
NO.
PART NO.
PART NAME
QTY.
REMARKS
1
2
3
4
5
6
PLATE, MODEL/SERIAL NUMBER ..................... 1 ................CONTACT PARTS DEPT.
DECAL, READ OWNERS MANUAL..................... 1 ................NPA-329
DECAL, BELT GUARD WARNING ....................... 1 ................NPA-989
DECAL: MIKASA MARK 120X60 ......................... 1 ................WATERTANK
DECAL: MQ MARK 71X55 ................................... 1 ................MQ/WATERTANK
DECAL: MIKASA MARK 125MM ......................... 1 ................WATERTANK
920203290
920203989
920101410
920201580
920105070
MVC-64E/EW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (05/11/06) — PAGE 31
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-64E/EW — MAIN BODY ASSY.
MAIN BODY ASSY. (NEW STYLE)
PAGE 32 — MVC-64E/EW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (05/11/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-64E/EW — MAIN BODY ASSY.
MAIN BODY ASSY. (NEW STYLE)
NO
1
2
3
4
5
6
7
11
12
13
14-1
14-2
14-3
16
17
18
19
20
PART NO
418117711
418216491
939010254
959404350
020310080
030210250
031110160
911221304
418457690
413436870
001220840
030208200
031108160
031108160
022710809
404418150
460446780
0320050150
952400130
001220825
030208200
070100312
418216470
001221035
030210250
031110160
418216480
001221053
030210250
031110160
418343420
020308060
030208200
031108160
413216250
404433430
952403450
001221020
030210250
413436720
001520845
020308060
PART NAME
VIBRATORY PLATE
BASE
SHOCK ABSORBER D45-H41
EARTH WIRE
NUT M10
WASHER, LOCK M10
WASHER, FLAT M10
ENGINE, ROBIN EX130D40040
BOLT, ENGINE
ENGINE NUT, REAR
BOLT 8X40T
WASHER, LOCK M8
WASHER, FLAT M8
WASHER, FLAT M8
NYLON NUT M8
SPACER 18X25X8 CLUTCH
CLUTCH ASSY.
QTY.
1
1
4
1
8
8
4
1
1
1
2
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
1
2
2
2
2
2
2
2
REMARKS
KEY
WASHER 9304
21
22-1
22-2
23
BOLT 8X25 H, SW
WASHER, LOCK
V-BELT RPF-3310
BELT COVER
BOLT 10X35 H, SW, PW
WASHER, LOCK
WASHER, FLAT
BELT COVER, IN.
BOLT 10X65 SW, PW
WASHER, LOCK
WASHER, FLAT
COVER SEAL, E/G
NUT M8
WASHER, LOCK
WASHER, FLAT
HANDLE LONG
RUBBER 20X32X28.5/52H
WASHER 11X35X4.5
BOLT 10X55 H,SW
WASHER, LOCK
RUBBER, HANDLE
SOCKET HEAD BOLT 8X45 T
NUT M8
25
26-1
26-2
26-3
27
28-1
28-2
28-3
29
31
32
33
41
45
46
47-1
47-2
49
50
51
MVC-64E/EW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (05/11/06) — PAGE 33
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-64E/EW—VIBRATOR ASSY.
VIBRATOR ASSY.
l
PAGE 34 — MVC-64E/EW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (05/11/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-64E/EW—VIBRATOR ASSY.
VIBRATOR ASSY.
NO
61
62
63
64
65
66
67
68
69
70
71
72
72
73
74
75
77
78
79
PART NO
418117730
001221445
030214350
031114260
418456950
060403020
418456960
418456970
002400820
418456990
418343400
040306307
040406307
418456980
951401920
952403450
002211030
953400270
953405260
PART NAME
VIBRATING CASE
BOLT 14X45 T
QTY.
1
4
4
4
1
1
1
2
8
1
1
2
2
1
1
1
REMARKS
WASHER, LOCK M14
WASHER, FLAT M14
CASE COVER/PULLEY
OIL SEAL TC-30458
CASE COVER/SHUT-OFF
PACKING
BOLT 8X20 SW, PW
COVER SEAL, VIB.
ECC. ROTOR SHAFT
BEARING 6307C3
BEARING 6307C4
PULLEY, VIB.
KEY 7X7X30
WASHER 11X35X4.5
BOLT 10X30 H, SW
PLUG 1/4X14 10L
PACKING
1
1
1
MVC-64E/EW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (05/11/06) — PAGE 35
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-64E/EW—WATERTANK ASSY.
WATER TANK ASSY.
PAGE 36 — MVC-64E/EW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (05/11/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-64E/EW—WATERTANK ASSY.
WATER TANK ASSY.
NO
91
92
PART NO
418216510
002211025
418910010
418910020
954300342
001241030
033910010
022910180
954403241
959403790
416338940
418343430
001220825
031108160
020308060
418457010
PART NAME
HOOK
BOLT 10X25 H, SW
WATER TANK, GREEN ............................. 1 ................. INCLUDES ITEM W/
WATERTANK, ORANGE ........................... 1 ................. INCLUDES ITEM W/
CAP, WATER TANK
BOLT 10X30 U
WASHER 10.5X21X2 SUS.
NYLON NUT M10 SUS.
COCK PT1/4, BH-1211 AL.
NUT PS-1/4
PIPE HOLDER, L
SPRINKLING PIPE
BOLT 8X25 T
WASHER, LOCK M8
NUT M8
RUBBER CAP
QTY.
1
3
REMARKS
101
101
102
103
104
105
107
108
110
111
112
113
114
115
*
*
1
1
2
1
1
1
1
1
1
2
1
1
*
*
*
*
MVC-64E/EW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (05/11/06) — PAGE 37
Download from Www.Somanuals.com. All Manuals Search And Download.
EX-130D40040 — AIR CLEANER ASSY.
AIR CLEANER ASSY.
PAGE 38 — MVC-64E/EW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (05/11/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
EX-130D40040 — AIR CLEANER ASSY.
AIR CLEANER ASSY.
NO
510
200
210
220
250
260
270
272
520
570
580
850
PART NO
PART NAME
QTY.
REMARKS
2773261500
2773263008
2773261008
2773260408
2773264008
2773260908
2773274108
2773274008
2773261107
0023806000
0110060050
0851080000
AIR CLEANER ASSY. ............................... 1 ................. INCLUDES ITEMS W/
*
BASE, CLEANER
PACKING, CLEANER
GASKET, CLEANER
COVER, CLEANER
LABEL, THROTTLE
WING, NUT
WING, NUT
CLEANER, ELEMENT
FLANGE NUT
1
1
1
1
1
1
1
1
2
1
1
*
*
*
*
*
*
*
*
FLANGE BOLT
RUBBER PIPE
MVC-64E/EW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (05/11/06) — PAGE 39
Download from Www.Somanuals.com. All Manuals Search And Download.
EX-130D40040 — CAMSHAFT ASSY.
CAMSHAFT ASSY.
l
PAGE 40 — MVC-64E/EW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (05/11/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
EX-130D40040 — CAMSHAFT ASSY.
CAMSHAFT ASSY.
NO
10
25
PART NO
PART NAME
QTY.
REMARKS
2773160111
2773510103
0240060010
2773860103
2773640103
2773650103
2773870203
2763560111
2773691103
2773710103
2773690203
2773691313
CAMSHAFT .............................................. 1 ................. INCLUDES ITEMS W/%
PIN, CAMSHAFT
O-RING
PIN, SPRING
RELEASE LEVER
CLIP
RETURN SPRING
CHAIN, TIMING
TENSIONER
SPRING, TENSIONER
PIN, TENSIONER
CHAIN, GUIDE
1
1
1
1
1
1
1
1
1
1
1
27
34%
35%
37%
38%
150
160
163
166
170
MVC-64E/EW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (05/11/06) — PAGE 41
Download from Www.Somanuals.com. All Manuals Search And Download.
EX-130D40040 — CARBURETOR ASSY.
CARBURETOR ASSY.
PAGE 42 — MVC-64E/EW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (05/11/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
EX-130D40040 — CARBURETOR ASSY.
CARBURETOR ASSY.
NO
PART NO
PART NAME
QTY. REMARKS
210
2766230210
1066253808
2776252508
2466242008
2776252008
2776253108
2276245108
2776250008
2776251508
2776250608
2146245008
2146254008
2266250608
2766244008
2526240508
2266270118
2776236008
2076241008
1066241008
2366268008
2366254108
2466239008
0642006410
0642007810
2774380101
27732902H3
27735902H3
27735903H3
CARBURETOR ASSY. .................................... 1....... INCLUDES ITEMS W/
*
210-1
210-3
210-5
210-8
THROTTLE VALVE
CHOKE VALVE
PILOT JET
CHOKE LEVER
THROTTLE SHAFT
BOLT
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
*
*
*
*
210-11
210-12
210-14
210-15
210-16
210-17
210-18
210-19
210-20
210-22
210-24
210-28
210-44
210-45
210-62
210-79
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
NEEDLE
FLOAT PIN
FLOAT BODY
PACKING
FLOAT CHAMBER PACKING
FLOAT ASSY.
MAIN NOZZLE
MAIN JET
CLIP
BOLT
AIR JET
AIR JET (PILOT)
SEAL, CHOKE
PACKING
SEAL, THROTTLE
RUBBER PACKING
CUP
CHOKE LEVER
INSULATOR
GASKET, INSULATOR
GASKET, INSULATOR
210-102
210-302
210-303
224
540
550
*
*
*
560
MVC-64E/EW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (05/11/06) — PAGE 43
Download from Www.Somanuals.com. All Manuals Search And Download.
EX-130D40040 — CRANKCASE ASSY.
CRANKCASE ASSY.
l
PAGE 44 — MVC-64E/EW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (05/11/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
EX-130D40040 — CRANKCASE ASSY.
CRANKCASE ASSY.
NO
PART NO
PART NAME
QTY. REMARKS
10
2771010241
0440250200
0600280021
2771501103
0440060020
0401140030
0211140020
2771100131
CRANKCASE CP, W/OIL SENSOR ............. 1 ........ INCLUDES ITEMS W/
*
30
OIL SEAL
BALL BEARING
PIPE KNOCK
OIL SEAL
PLUG
1
1
2
1
2
2
*
40
*
50
*
75
80
*
90$
210
GASKET
MAIN BEARING COVER CP ....................... 1 ........ INCLUDES ITEMS W/%
220% 0440250210
230% 0600250140
OIL SEAL
1
1
1
1
1
1
1
1
6
2
BALL BEARING
GOVERNOR GEAR
GOVERNOR SLEEVE
OIL GAUGE
FILLER, PLUG
GASKET
GASKET
FLANGE BOLT
PIPE KNOCK
250
260
270
275
280$
281
300
700
960
27745004H1
2774190103
2776360113
2776500103
0213160020
0213160020
0010408350
2771501103
2769900107
GASKET SET .............................................. 1 ........ INCLUDES ITEMS W/ $, ITEMS 620
AND 690 IN CYLINDER HEAD ASSY,
AND ITEM 340 IN MUFFLER ASSY
MVC-64E/EW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (05/11/06) — PAGE 45
Download from Www.Somanuals.com. All Manuals Search And Download.
EX-130D40040 — CRANKSHAFT/PISTON ASSY.
CRANKSHAFT/PISTON ASSY.
PAGE 46 — MVC-64E/EW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (05/11/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
EX-130D40040 — CRANKSHAFT/PISTON ASSY.
CRANKSHAFT/PISTON ASSY.
NO
10
50
PART NO
PART NAME
QTY.
REMARKS
2762020131
0180140020
0323030010
2762250110
2772300103
2762330103
2762340103
2762340303
2762340403
2762351117
2762351217
2762351317
2152500403
CRANKSHAFT
FLANGE NUT
WOODRUFF KEY
1
1
1
70
310
320
350
360
360
360
370
370
370
380
CONNECTING ROD ASSY. ...................... 1 ................. INCLUDES ITEMS W/
CONNECTING ROD BOLT
PISTON PIN
*
2
1
1
1
1
1
1
1
2
*
PISTON STD.
PISTON, 0.25 O.S.
PISTON, 050 O.S.
PISTON RING SET STD.
PISTON RING SET, 0.25 O.S.
PISTON RING SET, 0.5 O.S.
CLIP
MVC-64E/EW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (05/11/06) — PAGE 47
Download from Www.Somanuals.com. All Manuals Search And Download.
EX-130D40040 — CYLINDER HEAD ASSY.
CYLINDER ASSY.
PAGE 48 — MVC-64E/EW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (05/11/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
EX-130D40040 — CYLINDER HEAD ASSY.
CYLINDER ASSY.
NO
20#
26#
30
PART NO
PART NAME
VALVE GUIDE
STEM SEAL
VALVE, SPRING
SPRING RETAINER
STUD
QTY.
REMARKS
2371420103
2771601001
2793360103
2693370103
0105080250
0105060351
2763340133
2763350133
13210KA031
2773500203
0031305000
2773620100
2773620200
2
1
2
2
2
2
1
1
4
1
1
40
60#
70#
80
90
95
200
210
220
225
STUD
INTAKE VALVE
EXHAUST VALVE
COLLET VALVE
PIN, ROCKER
CLIP
ROCKER, ARM ASSY. IN ............................ 1 ........ INCLUDES ITEMS W/ +
ROCKER, ARM EX ...................................... 1 ........ INCLUDES ITEMS W/ +
ADJUSTING SCREW
NUT
FLANGE BOLT
CYLINDER HEAD ........................................ 1 ........ INCLUDES ITEMS W/#
GASKET HEAD
FLANGE BOLT
FLANGE BOLT
ROCKER, COVER
GASKET, ROCKER COVER
FLANGE BOLT
230+ 0149050020
240+ 0170050030
2
2
1
290
610
620
630
631
680
690
710
0110060020
2761300111
2761500113
0110080240
0010408350
2771550101
2771600103
0110060020
1
4
1
1
1
4
MVC-64E/EW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (05/11/06) — PAGE 49
Download from Www.Somanuals.com. All Manuals Search And Download.
EX-130D40040 — FUELTANK ASSY.
FUEL TANK ASSY.
PAGE 50 — MVC-64E/EW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (05/11/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
EX-130D40040 — FUELTANK ASSY.
FUEL TANK ASSY.
NO
10
20
23
30
40
48
60
63
80
90
PART NO
PART NAME
QTY. REMARKS
2766010201
0732005181
2769510103
0430430060
0641360010
0505120020
0023806000
0110060130
0851060000
X561100030
FUEL TANK, BLACK
LABEL, WARNING
LABEL, MODEL
FUEL TANK, CAP
FUEL FILTER
1
1
1
1
1
1
2
1
1
UNION
FLANGE, NUT
FLANGE, BOLT
RUBBER PIPE, 6DX11D
HOSE CLAMP, 10DX8BX1T
2
MVC-64E/EW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (05/11/06) — PAGE 51
Download from Www.Somanuals.com. All Manuals Search And Download.
EX-130D40040 — GOVERNOR ASSY.
GOVERNOR ASSY.
PAGE 52 — MVC-64E/EW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (05/11/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
EX-130D40040 — GOVERNOR ASSY.
GOVERNOR ASSY.
NO
10
20
30
40
50
60
70
80
300
310
340
350
355
360
365
395
396
435
440
450
480
485
486
PART NO
PART NAME
QTY.
REMARKS
2774230113
2774220133
2794270101
2774280113
0031305000
0130060240
0186060020
2794250223
2774600300
2774330301
2774350103
0200060170
0217060070
0043106250
2374500423
2774390203
0131050030
2774600201
0043104080
0023506000
2674510103
0110060020
2774370101
GOVERNOR, LEVER
GOVERNOR, SHAFT
GOVERNOR, ROD
ROD, SPRING
1
1
1
1
1
1
1
1
CLIP
BOLT & WASHER ASSY
NUT
GOVERNOR, SPRING
SPEED CONTROL ASSY ......................... 1 ................. INCLUDES ITEMS W/
SPEED CONTROL, LEVER
STOP, PLATE
WASHER
FRICTION, WASHER
SCREW
SPRING, ADJUST
CLAMP
SCREW AND WASHER ASSY
SPEED, CONT. BRACKET
SCREW
*
1
1
1
1
1
1
1
1
1
1
1
1
2
1
*
*
*
*
*
*
*
*
*
*
*
*
LOCK NUT
RETURN SPRING
FLANGE, BOLT
LINK ROD
*
MVC-64E/EW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (05/11/06) — PAGE 53
Download from Www.Somanuals.com. All Manuals Search And Download.
EX-130D40040 — IGNITION COIL/FLYWHEEL ASSY.
IGNITION COIL/FLYWHEEL ASSY.
PAGE 54 — MVC-64E/EW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (05/11/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
EX-130D40040 — IGNITION COIL/FLYWHEEL ASSY.
IGNITION COIL/FLYWHEEL ASSY.
NO
10
11
30
50
60
70
80
100
110
700
705
740
741
770
775
PART NO
PART NAME
QTY.
1
1
2
1
1
2
1
1
1
1
1
2
2
1
1
REMARKS
2767923011
2777943101
0011406250
27773102H1
X660000361
0150040090
0241070110
0650140150
0655000270
2777630111
KU31104311
0011406160
0150040090
2147900601
0110060020
FLYWHEEL
IGNITION COIL
BOLT & WASHER
WIRE 1
STOP SWITCH ASSY., ON-OFF
TAPPING SCREW
GROMMET
SPARK PLUG
SPARK PLUG CAP
OIL SENSOR
CONTROL ASSY, OIL SENSOR
BOLT AND WASHER ASSY
TAPPING SCREW
CLAMP
FLANGE BOLT
MVC-64E/EW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (05/11/06) — PAGE 55
Download from Www.Somanuals.com. All Manuals Search And Download.
EX-130D40040 — MUFFLER ASSY.
MUFFLER ASSY.
PAGE 56 — MVC-64E/EW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (05/11/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
EX-130D40040 — MUFFLER ASSY.
MUFFLER ASSY.
NO
310
320
340
350
360
361
365
440
445
PART NO
PART NAME
QTY.
REMARKS
2763010111
2773420111
2773520113
9802008280
0152060090
0110060010
0110080150
2773700101
0150040060
MUFFLER
1
1
1
2
2
1
1
1
2
MUFFLER COVER
GASKET, MUFFLER
FLANGE, NUT
TAPPING BOLT
FLANGE BOLT
FLANGE BOLT
DEFLECTOR
TAPPING SCREW
MVC-64E/EW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (05/11/06) — PAGE 57
Download from Www.Somanuals.com. All Manuals Search And Download.
EX-130D40040 — RECOIL STARTER ASSY.
RECOIL STARTER ASSY.
PAGE 58 — MVC-64E/EW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (05/11/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
EX-130D40040 — RECOIL STARTER ASSY.
RECOIL STARTER ASSY.
NO
PART NO
PART NAME
QTY.
REMARKS
10
2765120201
0732005140
0110060030
2775271111
2775270203
0010406160
0110060020
2685020130
2705011508
2695012008
5825011118
2615010008
2705012508
2275013108
2685014518
2705026108
2275015208
0110060010
BLOWER, HOUSING CP, BLACK
LABEL, TRADEMARK
FLANGE, BOLT
1
1
4
1
1
1
1
20
40
60
61
80
81
210
210-1
210-2
210-3
210-4
210-5
210-6
210-11
210-35
210-49
220
BAFFLE, CASE 1
BAFFLE, HEAD 2
FLANGE, BOLT
FLANGE, BOLT
RECOIL STARTER ASSY. ...................... 1.................... INCLUDES ITEMS W/
SPIRAL, SPRING
REEL
STARTER ROPE
STARTER KNOB
RACHET
FRICTION SPRING
STARTER PULLEY
RACHET GUIDE
SET SCREW
*
1
1
1
1
2
1
1
1
1
1
*
*
*
*
*
*
*
*
*
FLANGE, BOLT
MVC-64E/EW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (05/11/06) — PAGE 59
Download from Www.Somanuals.com. All Manuals Search And Download.
Effective: October 1, 2002
TERMS AND CONDITIONS OF SALE — PARTS
5. Parts must be in new and resalable
condition,intheoriginalMultiquippack-
age (if any), and with Multiquip part
numbersclearlymarked.
Multiquip reserves the right to quote and sell
directtoGovernmentagencies,andtoOriginal
Equipment Manufacturer accounts who use
our products as integral parts of their own
products.
PAYMENT TERMS
Terms of payment for parts are net 10 days.
FREIGHTPOLICY
All parts orders will be shipped collect or
prepaidwiththechargesaddedtotheinvoice.
All shipments are F.O.B. point of origin.
Multiquip’sresponsibilityceaseswhenasigned
manifesthasbeenobtainedfromthecarrier,
andanyclaimforshortageordamagemustbe
settledbetweentheconsigneeandthecarrier.
6. Thefollowingitemsarenotreturnable:
SPECIALEXPEDITINGSERVICE
a. Obsolete parts. (If an item is in the
price book and shows as being
replaced by another item, it is
obsolete.)
A$35.00surchargewillbeaddedtotheinvoice
forspecialhandlingincludingbusshipments,
insuredparcelpostorincaseswhereMultiquip
mustpersonallydeliverthepartstothecarrier.
b. Any parts with a limited shelf life
(such as gaskets, seals, “O” rings,
and other rubber parts) that were
purchased more than six months
priortothereturndate.
LIMITATIONSOFSELLER’SLIABILITY
MINIMUMORDER
Multiquip shall not be liable here under for
damagesinexcessofthepurchasepriceofthe
itemwithrespecttowhichdamagesareclaimed,
andinnoeventshallMultiquipbeliableforloss
of profit or good will or for any other special,
consequentialorincidentaldamages.
TheminimumchargeforordersfromMultiquip
is $15.00 net. Customers will be asked for
instructionsregardinghandlingofordersnot
meetingthisrequirement.
c. Anylineitemwithanextendeddealer
netpriceoflessthan$5.00.
RETURNEDGOODSPOLICY
d. Special order items.
Returnshipmentswillbeacceptedandcredit
willbeallowed,subjecttothefollowingprovi-
sions:
LIMITATIONOFWARRANTIES
e. Electricalcomponents.
f. Paint,chemicals,andlubricants.
g. Decalsandpaperproducts.
h. Itemspurchasedinkits.
Nowarranties,expressorimplied,aremadein
connectionwiththesaleofpartsortradeacces-
soriesnorastoanyenginenotmanufactured
byMultiquip.Suchwarrantiesmadeinconnec-
tion with the sale of new, complete units are
madeexclusivelybyastatementofwarranty
packagedwithsuchunits,andMultiquipnei-
ther assumes not authorizes any person to
assume for it any other obligation or liability
whatever in connection with the sale of its
products.Apartfromsuchwrittenstatementof
warranty, there are no warranties, express,
impliedorstatutory,whichextendbeyondthe
descriptionoftheproductsonthefacehereof.
1. AReturnedMaterialAuthorizationmust
be approved by Multiquip prior to ship-
ment.
7. The sender will be notified of any
materialreceivedthatisnotacceptable.
2. ToobtainaReturnMaterialAuthorization,
alistmustbeprovidedtoMultiquipParts
Salesthatdefinesitemnumbers,quanti-
ties, and descriptions of the items to be
returned.
8. Such material will be held for five
workingdaysfromnotification,pending
instructions. If a reply is not received
within five days, the material will be
returnedtothesenderathisexpense.
a. Thepartsnumbersanddescriptions
must match the current parts price
list.
9. Creditonreturnedpartswillbeissuedat
dealer net price at time of the original
purchase,lessa15%restockingcharge.
b. The list must be typed or computer
generated.
10. Incaseswhereanitemisaccepted,for
which the original purchase document
cannotbedetermined,thepricewillbe
basedonthelistpricethatwaseffective
twelvemonthspriortotheRMAdate.
c. The list must state the reason(s) for
l
thereturn.
d. The list must reference the sales
order(s)orinvoice(s)underwhichthe
itemswereoriginallypurchased.
11. Credit issued will be applied to future
purchasesonly.
e. The list must include the name and
phonenumberofthepersonrequest-
ingtheRMA.
PRICINGANDREBATES
Prices are subject to change without prior
notice.Pricechangesareeffectiveonaspe-
cific date and all orders received on or after
that date will be billed at the revised price.
Rebatesforpricedeclinesandaddedcharges
forpriceincreaseswillnotbemadeforstock
onhandatthetimeofanypricechange.
3. AcopyoftheReturnMaterialAuthoriza-
tionmustaccompanythereturnshipment.
4. Freight is at the sender’s expense. All
partsmustbereturnedfreightprepaidto
Multiquip’sdesignatedreceivingpoint.
PAGE 60 — MVC-64E/EW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (05/11/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE PAGE
MVC-64E/EW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (05/11/06) — PAGE 61
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION & PARTS MANUAL
HERE'S HOW TO GET HELP
OPERATION & PART
PLEASE HAVETHE MODEL AND SERIAL
NUMBER ON-HANDWHEN CALLING
UNITED STATES
Multiquip Corporate Office
18910 Wilmington Ave.
Carson, CA 90746
MQ Parts Department
Tel. (800) 421-1244
800-427-1244
310-537-3700
Fax: 800-672-7877
Fax: 310-637-3284
Fax (800) 537-3927
Contact: [email protected]
Mayco Parts
800-306-2926
310-537-3700
Warranty Department
800-421-1244, Ext. 279 Fax:310-537-1173
310-537-3700, Ext. 279
Fax:800-672-7877
Fax:310-637-3284
Service Department
800-421-1244
Technial Assistance
800-478-1244
Fax:310-537-4259
Fax:310-631-5032
310-537-3700
MEXICO
MQ Cipsa
UNITED KINGDOM
Multiquip (UK) Limited Head Office
Hanover Mill, Fitzroy Street,
Ashton-under-Lyne,
Carr. Fed. Mexico-Puebla KM 126.5
Momoxpan, Cholula, Puebla72760Mexico
Tel: (52) 222-225-9900
Fax: (52) 222-285-0420
Tel: 0161 339 2223
Fax: 0161 339 3226
Lancashire OL7 0TL
CANADA
Multiquip
BRAZIL
Multiquip
4110IndustrielBoul.
Laval, Quebec, Canada H7L 6V3
Tel: (450) 625-2244
Fax: (450) 625-8664
Av. Evandro Lins e Silva, 840 - grupo 505 Tel: 011-55-21-3433-9055
Barra de Tijuca - Rio de Janeiro Fax: 011-55-21-3433-9055
© COPYRIGHT 2005, MULTIQUIP INC.
Multiquip Inc., Mikasa, and the MQ logo are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without written permission. All other
trademarks are the property of their respective owners and used with permission.
This manual MUST accompany the equipment at all times. This manual is considered a permanent part of the equipment and should remain with the unit if resold.
The information and specifications included in this publication were in effect at the time of approval for printing. Illustrations are based on the MVC-64E/EW Plate Compactor.
Illustrations, descriptions, references and technical data contained in this manual are for guidance only and may not be considered as binding. Multiquip Inc. reserves the
right to discontinue or change specifications, design or the information published in this publication at any time without notice and without incurring any obligations.
Your Local Dealer is:
Download from Www.Somanuals.com. All Manuals Search And Download.
|