OPERATION AND PARTS MANUAL
Plate Compactor
Models
MVC-64VH/VHW
(Honda GX120U1 Gasoline Engine)
Revision #1 (03/01/07)
To find the latest revision of this
publication, visit our website at:
THIS MANUAL MUST ACCOMPANYTHE EQUIPMENT AT ALLTIMES.
Download from Www.Somanuals.com. All Manuals Search And Download.
l
PAGE 2 — MVC-64VH/VHW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (03/01/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE PAGE
MVC-64VH/VHW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (03/01/07) — PAGE 3
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
Honda GX120U1SM12
Engine
Multiquip MVC-64VH/
VHW Plate Compactor
Cylinder Head Assembly.................................... 38-39
Cylinder Barrel (Recoil) Assembly ..................... 40-41
Crankcase Cover Assembly............................... 42-43
Crankshaft Assembly ......................................... 44-45
Piston/Connecting Rod Assembly ...................... 46-47
Camshaft Assembly ........................................... 48-49
Recoil Starter ..................................................... 50-51
Fan Cover Assembly .......................................... 52-53
Carburetor Assembly ......................................... 54-55
Air Cleaner Assembly......................................... 56-57
Muffler Assembly ............................................... 58-59
Fuel Tank Assembly ........................................... 60-61
Flywheel Assembly ............................................ 62-63
Ignition Coil Assembly ........................................ 64-65
Control Assembly ............................................... 66-67
Label Assembly.................................................. 68-69
Proposition 65 Warning ............................................. 2
Here's How To Get Help ............................................ 3
Table Of Contents ..................................................... 4
Parts Ordering Procedures ....................................... 5
Specifications ............................................................ 6
Dimensions ............................................................... 7
Safety Message Alert Symbols .............................. 8-9
Rules For Safe Operation.....................................10-11
Operation and Safety Decals .................................. 12
General Information ................................................ 13
Components (Plate Compactor) ............................. 14
Components (Honda GX120U1SM12 Engine) ....... 15
Inspection........................................................... 16-17
Initial Start-Up/Operation ................................... 18-19
Maintenance ...................................................... 20-21
Preparation For Long Term Storage ....................... 22
Troubleshooting (Engine)................................... 23-24
Troubleshooting (Plate Compactor) ........................ 25
Explanation Of Codes In Remarks Column ............ 26
Suggested Spare Parts ........................................... 27
Terms and Conditions Of Sale — Parts .................. 70
Component Drawings
Name Plate and Decals ..................................... 28-29
Main Body Assembly.......................................... 30-31
l
Vibrator Assembly .............................................. 34-35
Water Tank ......................................................... 36-37
As a continuing effort to
update our parts book, contact
the MULTIQUIP literature
department for the latest
revision of your "Operation
and Parts Manual"
Specification and part number
are subject to change without
notice.
PAGE 4 — MVC-64VH/VHW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (03/01/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS ORDERING PROCEDURES
Ordering parts has never been easier!
Choose from three easy options:
Best Deal!
Order via Internet (Dealers Only)
Orderpartson-lineusingMultiquip’sSmartEquipwebsite!
:
If you have an MQ Account, to obtain a
Username and Password, E-mail us at:
■
■
■
View Parts Diagrams
Order Parts
PrintSpecificationInformation
To obtain an MQ Account, contact your
District Sales Manager for more information.
Use the internet and qualify for a 5% Discount
on Standard orders for all orders which include
complete part numbers.*
Gotowww.multiquip.comandclickon
to log in and save!
Order Parts
Note: Discounts Are Subject To Change
Fax your order in and qualify for a 3% Discount
on Standard orders for all orders which include
complete part numbers.*
Order via Fax (Dealers Only)
:
All customers are welcome to order parts via Fax.
Domestic (US) Customers dial:
1-800-6-PARTS-7 (800-672-7877)
Note: Discounts Are Subject To Change
Domestic (US) Dealers Call:
1-800-427-1244
Order via Phone:
Non-Dealer Customers:
International Customers should contact
their local Multiquip Representatives for
Parts Ordering information.
Contact your local Multiquip Dealer for
parts or call 800-427-1244 for help in
locating a dealer near you.
When ordering parts, please supply:
❒
❒
❒
❒
❒
❒
Dealer Account Number
❒
Specify Preferred Method of Shipment:
✓
Fed Ex/UPS
✓ DHL
Dealer Name and Address
■
■
Priority One
Ground
✓
Truck
Shipping Address (if different than billing address)
Return Fax Number
■ Next Day
Applicable Model Number
■
Second/ThirdDay
Quantity, Part Number and Description of Each Part
Unless otherwise indicated by customer, all orders are treated asStandard Orders and will ship
within24hours.WewillmakeeveryefforttoshipAirShipmentsthesamedaytheorderisreceived,
if received prior to 2PM PST. Stock Orders must be noted on fax or web order form.
NOTE
WE ACCEPT ALL MAJOR CREDIT CARDS!
MVC-64VH/VHW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (03/01/07) — PAGE 5
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-64VH/VHW — SPECIFICATIONS
TABLE 1. COMPACTOR SPECIFICATIONS
Model
MVC-64VH/VHW
Centrifugal Force
2,275 lbs. (1,032 kg)
Vibration Frequency
5,600 vpm (93 Hz)
Maximum Forward Speed
Plate Size (L x W)
82 ft/min (25 m/min)
22.4 x 13.8 in (570 x 350 mm)
36.6 x 13.8 x 39.4 in (930 x 350 x 1000 mm)
161 lbs. (80 kg)
Overall Dimensions (L x W x H)
Operating Weight (with water tank)
Operating Weight (without water tank)
Maximum Area of Compaction
176 lbs. (72 kg)
5,658 sq. ft/hr (526 sq. m/hr)
Table 2. Specifications (Engine)
Model
HONDA GX120U1SM12
Air-cooled 4 stroke, Single
Cylinder, OHV, Horizontal
Shaft Gasoline Engine
Type
2.4 in. x 1.7 in.
(60 mm x 42 mm)
Bore X Stroke
Displacement
Max Output
119 cc (7.2 cu-in)
4.0 H.P./3600 R.P.M.
0.66 US gal. (2.5 liters)
Engine
l
Fuel Tank Capacity
Unleaded Automobile
Gasoline
Fuel
Lube Oil Capacity
.60 liters (0.63 qts)
Centrifugal Fly-weight Type
Recoil Start
Speed Control
Method
Starting Method
Dimension
(L x W x H)
11.7 x 13.4 x 12.5 in.
(297 x 341 x 318 mm)
Dry
Net Weight
28.7 lbs (13 Kg.)
PAGE 6 — MVC-64VH/VHW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (03/01/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-64VH/VHW — DIMENSIONS
E
A
F
D
C
B
Figure 1. MVC-64VH/VHW Plate Compactor Dimensions
TABLE 3. DIMENSIONS
DESCRIPTION
REFERENCE LETTER
DIMENSION In. (mm)
39 In. (1000 mm)
13 In. (330 mm)
24 In. (609 mm)
22 In. (560 mm)
37 In. (940 mm)
23 In. (590 mm)
Height (Handle Upright)
A
B
C
D
E
F
Width
Length (Handle Upright)
Plate Length
Length (Handle Lowered)
Height (Compactor Only)
30 x 15 x 30 In.
(762 x 381 x 762)
Shipping Dimensions
MVC-64VH/VHW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (03/01/07) — PAGE 7
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-64VH/VHW — SAFETY MESSAGE ALERT SYMBOLS
HAZARD SYMBOLS
FORYOUR SAFETY ANDTHE SAFETY OF OTHERS!
Potential hazards associated with the operation of the MQ
Model MVC-64VH/VHW Plate Compactor. will be referenced
with Hazard Symbols which appear throughout this manual,
and will be referenced in conjunction with Safety Message
Alert Symbols.
Safety precautions should be followed at all times when operating
this equipment. Failure to read and understand the Safety
Messages and Operating Instructions could result in injury to
yourself and others.
This Owner's Manual has been
developed to provide complete
instructions for the safe and efficient
operation of the MQ Model MVC-
64VH/VHW Plate Compactor.
Refer to the engine manufacturers
instructions for data relative to its
safe operation.
WARNING - Lethal Exhaust Gas Hazards
Engine exhaust gases contain
poisonous carbon monoxide. This gas
is colorless and odorless, and can
cause death if inhaled. NEVER operate
this equipment in a confined area or
enclosed structure that does not provide ample free flow
air.
Before using this plate compactor, ensure that the
operating individual has read and understands all
instructions in this manual.
SAFETY MESSAGE ALERT SYMBOLS
DANGER - Explosive Fuel Hazards
The three (3) Safety Messages shown below will inform
you about potential hazards that could injure you or others.
The Safety Messages specifically address the level of
exposure to the operator, and are preceded by one of
three words: DANGER, WARNING, or CAUTION.
Gasoline is extremely flammable, and
its vapors can cause an explosion if
ignited. DO NOT start the engine near
spilled fuel or combustible fluids.
DO NOT fill the fuel tank while the engine is running or
hot. DO NOT overfill tank, since spilled fuel could ignite if
it comes into contact with hot engine parts or sparks from
the ignition system. Store fuel in approved containers, in
well-ventilated areas and away from sparks and flames.
DANGER
You WILL be KILLED or SERIOUSLY injured if you DO
NOT follow directions.
WARNING - Burn Hazards
WARNING
You CAN be KILLED or SERIOUSLY injured if you DO
NOT follow directions.
l
Engine components can generate extreme
heat. To prevent burns, DO NOT touch
these areas while the engine is running or
immediately after operations. Never
operate the engine with heat shields or heat
guards removed.
CAUTION
You CAN be INJURED if you DO NOT follow directions.
WARNING - Respiratory Hazards
ALWAYS wear approved respiratory
protection when required.
PAGE 8 — MVC-64VH/VHW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (03/01/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-64VH/VHW — SAFETY MESSAGE ALERT SYMBOLS
CAUTION - Equipment Damage Hazards
CAUTION - Rotating Parts Hazards
NEVER operate equipment with covers,
or guards removed. Keep fingers, hands,
hair and clothing away from all moving
parts to prevent injury.
Other important messages are provided throughout this
manual to help prevent damage to your light tower, other
property, or the surrounding environment.
CAUTION - Accidental Starting Hazards
WARNING - Read Manual
ALWAYS place the power source, circuit
breakers or ON/OFF switch in the OFF
position, when the generator is not in use,
unless connected to transfer switch.
Before attempting to operate
the plate compactor, and to
avoid serious injury to
personnel, always read and
understand operation manual.
Failure to read and understand
CAUTION - Eye and Hearing Hazards
operation manual
could
result in serious harm or even
death!
ALWAYS wear approved eye and
hearing protection.
DANGER - Refueling Hazard
DO NOT refuel plate copmpactor if compactor is placed
inside truck bed with PLASTIC LINER. Possibility exists
of explosion or fire due to static electricity.
MVC-64VH/VHW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (03/01/07) — PAGE 9
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-64VH/VHW — RULES FOR SAFE OPERATION
■
■
■
NEVER touch the hot exhaust
manifold, muffler or cylinder. Allow
these parts to cool before servicing
engine or mixer.
CAUTION - Read Manual!
Failure to follow instructions in this
manual may lead to serious injury or
even death! This equipment is to be
operated by trained and qualified
personnel only! This equipment is for
industrial use only.
High Temperatures – Allow the
engine to cool before adding fuel or
performing service and maintenance functions. Contact
with hot! components can cause serious burns.
The engine section of this mixer requires an adequate
free flow of cooling air. NEVER operate the compactor
in any enclosed or narrow
The following safety guidelines should always be used when
operating the MQ Mikasa Model MVC-64VH/VHW Plate
Compactor.
area where free flow of the
GENERAL SAFETY
air is restricted. If the air
flow is restricted it will
cause serious damage to
the compactor or engine
and may cause injury to
people. Remember the
plate compactor's engine
gives off DEADLY carbon monoxide gas.
■
■
■
DO NOT operate or service this equipment before reading
this entire manual.
This equipment should not be operated by persons under
18 years of age.
NEVER operate this equipment without proper protective
clothing, shatterproof glasses, steel-toed boots and other
protective devices required by the job.
■
■
ALWAYS refuel in a well-ventilated area, away from sparks
and open flames.
ALWAYS use extreme caution when
working with flammable liquids. When
refueling, stop the engine and allow it to
cool. DO NOT smoke around or near the
machine. Fire or explosion could result
from fuel vapors, or if fuel is spilled on a
hot engine.
■
■
NEVER operate this equipment when not
feeling well due to fatigue, llness or taking
medicine.
NEVER operate this equipment under the
influence of drugs or alcohol.
■
■
NEVER operate the plate compactor in
an explosive atmosphere or near
combustible materials. An explosion or
fire could result causing severe bodily
harm or even death.
■
ALWAYS wear proper respiratory (mask),
hearing and eye protection equipment when
operating the plate compactor.
Topping-off to filler port is dangerous, as it tends to spill
fuel.
■
■
Maintain this equipment in a safe operating condition at
all times.
ALWAYS store equipment properly when it is not being used.
Equipment should be stored in a clean, dry location out of the
reach of children.
■
■
■
Whenever necessary, replace nameplate, operation and
safety decals when they become difficult read.
Manufacture does not assume responsibility for any
accident due to equipment modifications.
NEVER use accessories or attachments, which are not
recommended by Multiquip for this equipment. Damage
to the equipment and/or injury to user may result.
PAGE 10 — MVC-64VH/VHW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (03/01/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-64VH/VHW — RULES FOR SAFE OPERATION
■
■
■
NEVER run engine without air filter. Severe engine damage
TRANSPORTING
may occur.
■
■
ALWAYS shutdown engine before transporting.
Tighten fuel tank cap securely and close fuel cock to
prevent fuel from spilling.
ALWAYS service air cleaner frequently to prevent carburetor
malfunction.
ALWAYS be sure the operator is familiar with proper safety
precautions and operations techniques before using
compactor.
■
Drain fuel when transporting compactor over long
distances or bad roads.
MAINTENANCE
■
■
ALWAYS read, understand, and follow procedures in
Operator’s Manual before attempting to operate equipment.
■
NEVER lubricate components or attempt service on a
running compactor.
Refer to the Honda Engine Owner's Manual for engine
technical questions or information.
■
ALWAYS allow the plate compactor a proper amount of
time to cool before servicing.
■
■
Keep the compactor in proper running condition.
Fix damage to the plate compactor immediately and
always replace broken parts.
Dispose of hazardous waste properly. Examples of
potentially hazardous waste are used motor oil, fuel and
fuel filters.
Loading and Unloading (Crane)
■
Before lifting, make sure that machine parts (lifting bale and
vibration insulator) are not damaged and screws are not
loosened or lost.
■
■
■
ALWAYS make sure crane or lifting device has been properly
secured to the lifting bale on the compactor.
DO NOT use food or plastic containers to dispose of
hazardous waste.
EMERGENCIES
■
ALWAYS know the location of the nearest fire
extinguisher and first aid kit.
■
In emergencies always know the location of the
nearest phone or keep a phone on the job site.
Also know the phone numbers of the nearest
ambulance, doctor and fire department. This
information will be invaluable in the case of an
emergency.
■
■
■
■
NEVER lift the compactor while the engine is running.
Use adequate lifting cable (wire or rope) of sufficient strength.
Use one point suspension hook and lift straight upwards.
NEVER allow any person or animal to stand underneath the
machine while lifting.
■
Try not to lift compactor to unnecessary heights.
MVC-64VH/VHW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (03/01/07) — PAGE 11
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-64VH/VHW — OPERATION AND SAFETY DECALS
Machine Safety Decals
The MVC-64VH/VHW Plate Compactor is equipped with a number of safety decals (Figure 2). These decals are provided for
operator safety and maintenance information.The illustration below shows these decals as they appear on the machine.Should any
of these decals become unreadable, replacements can be obtained from your dealer.
l
Figure 2. Operation and Safety Decals
PAGE 12 — MVC-64VH/VHW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (03/01/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-64VH/VHW — GENERAL INFORMATION
Definition of Plate Compactor
Frequency/Speed
The Mikasa MVC-64VH/VHW is a walk behind, plate compactor
designed for the compaction of sand, mixed soils and asphalt.
This plate compactor is a powerful compacting tool capable of
applying a tremendous force in consecutive high frequency
vibrations to a soil surface. Its applications include compacting
for road, embankments and reservoirs as well as backfilling for
gas pipelines, water pipelines and cable installation work.
The compactor's vibrating plate has a frequency of 5,600 vpm
(vibrations per minute). The travel speed of the compactor is
approximately 82 ft./minute (25 meters/minute).
Engine
The Mikasa MVC-64VH/VHW Plate Compactor is equipped with
a Honda GX120U1SM12 gasoline engine.
Controls
The MVC-64VH/VHW is small and lightweight. It can be easily
handled by one person in confined areas. It has an accessible
front-mounted vibrator assembly.The sealed belt cover keeps
dirt and rocks away from the belt.
Before starting the MVC-64VH/VHW Plate Compactor identify
and understand the function of the controls and components as
indicated Figure 3.
Vibratory Plate
The vibratory plate of the compactor produces low amplitude
high frequency vibrations, designed to compact granular soils
and asphalt.
The resulting vibrations cause forward motion.The engine and
handle are vibration isolated from the vibrating plate.
MVC-64VH/VHW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (03/01/07) — PAGE 13
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-64VH/VHW — COMPONENTS (PLATE COMPACTOR)
1
10
4
9
3
2
5
WATER TANK
(MVC-64VHW ONLY)
8
7
6
Figure 3. MVC-64VH/VHW Plate Compactor Components
6. Belt Cover – Remove this cover to gain acess to the V-
belts.NEVER run the compactor without theV-belt cover.If
the V-belt cover is not installed, the possibility exist that
your hand may get caught between the V-belt and clutch,
thus causing serious injury and bodily harm.
Figure 3 shows the location of the components and general
maintenance parts. The function of each component is described
below:
1. Water Tank Cap (for MVC-64VHW only) – Remove this
cap to add water to the watelr tank.
7. Vibrating Plate – A flat, open plate made of durable cast
2. FuelTank Cap – Remove this cap to add fuel.
iron construction used in the compacting of soil.
3.
Lifting Bail – When lifting of the compactor is required
either by forklift, crane etc., tie rope or chain around this
lifting point.
8. Vibration Case – Encloses the eccentric, gears and
counter weights.
9. Water Shut-OffValve (for MVC-64HW only) – Turn this
valve downward to let water flow from the water tank to the
water tube.
4. Handle Bar – When operating the compactor use this
handle bar to maneuver the compactor.
5. Gasoline Engine – This plate compactor uses a HONDA
GX120U1SM12 HONDA engine. Refer to the HONDA
owner's manual for engine information.
10. WaterTank (for MVC-64HW only) – Holds 10.6 quarts
(10 liters) of water, removable no tools required.
PAGE 14 — MVC-64VH/VHW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (03/01/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-64VH/VHW — COMPONENTS (HONDA GX120U1SM12 ENGINE)
Figure 4. Engine Controls & Components
INITIAL SERVICING
8. Spark Plug – Provides spark to the ignition system. Set
spark plug gap to 0.6 - 0.7 mm (0.028 - 0.031 inch) for
HONDA engine. Clean spark plug once a week.
The engine (Figure 4) must be checked for proper lubrication and
filled with fuel prior to operation. Refer to the manufacturer's engine
manual for instructions and details of operation and servicing.
9. Muffler – Used to reduce noise and emissions.
1. Fuel Filler Cap – Remove this cap to add unleaded
gasoline to the fuel tank. Make sure cap is tightened
securely. DO NOT over fill.
Warning - Hot Surface
Engine components can generate extreme heat.
To prevent burns, DO NOT touch these areas
while the engine is running or immediately after
operating. NEVER operate the engine with the
muffler removed.
2. Throttle Lever – Used to adjust engine RPM speed (lever
advanced forward SLOW, lever back toward operator
FAST).
3. Engine ON/OFF Switch – ON position permits engine
starting, OFF position stops engine operations.
10. Fuel Tank – Holds unleaded gasoline. For additional
4. Recoil Starter (pull rope) – Manual-starting method. Pull
the starter grip until resistance is felt, then pull briskly and
smoothly.
information refer to engine owner's manual.
5. FuelValve Lever – OPEN to let fuel flow, CLOSE to stop
Operating the engine without an air
filter, with a damaged air filter, or a
filter in need of replacement will
allow dirt to enter the engine,
causing rapid engine wear.
the flow of fuel.
6. Choke Lever – Used in the starting of a cold engine, or in
cold weather conditions. The choke enriches the fuel
mixture.
7. Air Cleaner – Prevents dirt and other debris from entering
the fuel system. Remove wing-nut on top of air filter
cannister to gain access to filter element.
MVC-64VH/VHW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (03/01/07) — PAGE 15
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-64VH/VHW — INSPECTION
The Oil Alert system will
automatically stop the engine
before the engine falls below safe
Before Starting
1. Read safety instructions at the beginning of manual.
limits. Always be sure to check
the engine oil level prior to starting
the engine.
2. Cleanthecompactor,removingdirtanddust.Particularly,the
bottom of the plate, engine cooling air inlet, carburetor and
aircleaner.
Table 4. Oil Type
3. Checktheairfilterfordirtanddust.Iftheairfilterisdirty,blow
throughtheairfiltercartridgefromtheinside,movingajetof
dry compressed air up and down until all dust is removed.
Otherwise replace air filter with a new one.
Season
Summer
Spring/Fall
Winter
Temperature
25°C or Higher
25°C~10°C
Oil Type
SAE 10W-30
SAE 10W-30/20
SAE 10W-10
4. Check carburetor for external dirt and dust. Clean with dry
compressedair.
0°C or Lower
5. Check fastening nuts and bolts for tightness. Loosened
screws or bolts due to vibration, could lead to unexpected
accident.
Danger - Flammable Fuel
Motor fuels are highly flammable and can
be dangerous if mishandled. DO NOT
smoke while refueling. DO NOT attempt to
refuel the compactor if the engine is hot! ,
running or in the dark.
Engine Oil Check
1. To check the engine oil level, place the plate compactor on
secure level ground with the engine stopped.
2. Remove the filler cap/dipstick from the engine oil filler hole
(Figure 5) and wipe it clean.
Danger - Flammable Fuel
Adding fuel to the tank should be done only
when the engine is stopped and has had an
opportunity to cool down. In the event of a fuel
spill, DO NOT attempt to start the engine until
the fuel residue has been completely wiped
up, and the area surrounding the engine is
dry.
Fuel Check
1. Remove the gasoline cap located on top of fuel tank.
2. Visuallyinspecttoseeiffuellevelislow. Iffuelislow, replenish
with unleaded fuel.
Figure 5. EnginelOil Dipstick
3. Insertandremovethedipstickwithoutscrewingitintothefiller
neck. Check the oil level shown on the dipstick.
3. Whenrefueling,besuretouseastrainerforfiltration.DONOT
top-off fuel. Wipe up any spilled fuel.
4. If the oil level is low (Figure 6), fill to the edge of the oil filler
hole with the recommended oil type (Table 4).
UPPER LIMIT
Caution - Spilled Fuel
Since spilled fuel could ignite if it comes into contact with hot engine parts,
ALWAYS pour fuel from the recoil starter side of the compactor.Allow
engine to cool! before refueling.Wipe up any spilled fuel immediately.
LOWER LIMIT
Figure 6. Engine Oil Dipstick
PAGE 16 — MVC-64VH/VHW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (03/01/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-64VH/VHW — INSPECTION
V-Belt Check
Caution -V-Belt check
2. TheV-belt tension is proper if theV-belt bends 10 to 15 mm
(Figure 10) when depressed with finger at midway between
the clutch and vibration pulley shafts.
NEVER attempt to check theV-belt with the engine running.
Severe injury can occur if your hand (Figure 7) gets caught
betweentheV-beltandtheclutch.Alwaysusesafetygloves.
CLUTCH
PULLEY
Figure 9.V-BeltTension
3. A looseV-belt will decrease the power transmission output,
causing reduced compaction and premature wear of the
belt.
VIBRATOR
PULLEY
4. If theV-belt becomes worn or loose, replace it .
Figure 7.V-Belt Hazard
Vibrator Oil Check
1. Tocheck theV-belttension,removethe boltsthatsecurethe
belt cover to the frame as shown in Figure 8.
1. PlacetheMVC-64VH/VHWplatecompactorhorizontallyon
aflatsurface.Makesurethecompactorislevelwhencheck-
ing the oil in the vibrator assembly.
2. Check vibratoroillevelbyremoving theplug (vibrator oilgauge)
asshowninFigure10. Theoillevelshouldbeuptotheoilplug.
If oil is required, replace using only SAE 10W-30 motor oil.
Figure 10.Vibrator Oil Plug
Figure 8.V-Belt Cover Removal
MVC-64VH/VHW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (03/01/07) — PAGE 17
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-64VH/VHW — INITIAL START-UP
The CLOSED position of the
Caution - Read Manual
choke lever enriches the fuel
mixture for starting a COLD
D
DO NOT attempt to operate the plate compactor
until the Safety, General Information and
Inspection sections of this manual have been
read and thoroughly understood.
engine. The OPEN position
provides the correct fuel mixture
for normal operation after
starting, and for restarting a
warm engine.
1. Place the fuel valve lever (Figure 11) in the "ON" position.
4. Place the throttle lever (Figure 14) halfway between fast
andslow.
Figure 11. Fuel Valve Lever
2. Place the Engine ON/OFF switch (Figure 12) in the "ON"
position.
Figure 14. Throttle Lever
5. Grasp the starter grip (Figure 15) and slowly pull it out.The
resistancebecomesthehardestatacertainposition,corre-
spondingthecompressionpoint.Rewindtheropealittlefrom
that point and pull out sharply.
Caution - Starter Rope
D
DO NOT pull the starter rope all the way to the end.
Figure 12. Engine ON/Off Switch
DO NOT release the starter rope after pulling. Allow it to
rewind as soon as possible.
3. PlacetheChokeLever(Figure13)inthe"OPEN"position.
l
nn
Figure 13. Choke Lever
Figure 15. Starter Grip
PAGE 18 — MVC-64VH/VHW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (03/01/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-64VH/VHW — INITIAL START-UP/OPERATION
6. If the engine has started, slowly return the choke lever
Operation
(Figure 13) to the CLOSED position. If the engine has not
started repeat steps 1 through 5.
CAUTION - Safety Rules
7. Beforethecompactorisputintooperationruntheenginefor
3-5minutes.
Make sure to follow all safety rules referenced in the safety
sectionofthismanualbeforeoperatingcompactor. Keepwork
area clear of debris and other objects that could cause
damage to the compactor or bodily injury.
8. Check for abnormal engine noises or fuel leaks.
1. Oncetheenginehasstarted, movetheenginethrottlelever
quickly to the fastposition.
Stopping The Engine
Normal Shutdown
2. With the throttle lever in the fast position, the engine speed
should be around 2,300 RPM, therefore engaging the cen-
trifugalclutch.
Caution - Stopping Engine
Always move the throttle lever
quickly without hesitation, because
increasing the engine speed slowly
NEVER stop the engine suddenly while working at high
speeds.
causes the clutch to slip.
1. Place the throttle lever (Figure 14) in slow position, and
listen for the engine speed to decrease.
3. Firmlygaspthecompactor'shandlebar withbothhands,the
compactor will begin moving forward.
2. Place the Engine ON/OFF switch (Figure 12) in the "OFF
"position.
4. Slowlywalkbehindthecompactorandbeonthelookout for
anylargeobjectsorforeignmatterthatmightcausedamage
to the compactor or bodily injury.
3. Placethefuelvalvelever(Figure11)inthe"OFF"position.
Emergency Shutdown
5. Compactortravelingspeedmaydroponsoilswhichcontain
clay, however there may be cases where traveling speed
drops because the compaction plate does not leave the
ground surface easily due to the composition of the soil.To
rectify this problem do the following:
1. Move the throttle lever quickly to the SLOW position, and
place the engine ON/OFF switch in the OFF position.
z
Check the bottom plate to see if clay or equivalent
material has been lodged in the plate mechanism. If so,
wash with water and remove.
z
z
Remember the compactor does not work as efficiently
on clay or soils that have a high moisture content level.
If the soil has a high moisture level, dry soil to appropriate
moisture content level or carry out compaction twice.
MVC-64VH/VHW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (03/01/07) — PAGE 19
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-64VH/VHW — MAINTENANCE
CAUTION - Inspection Intervals
CAUTION - Inspection
These inspection intervals are for operation under normal
conditions. Adjust your inspection intervals based on the
number of hours plate compactor is in use, and particular
working conditions.
Inspection and other services should always be carried out
on hard and level ground with the engine shut down.
Inspection and Maintenance ServiceTables.
1. To make sure your plate compactor is always in good
working condition before using, carry out the maintenance
inspection in accordance with Tables 5 through 7.
CAUTION - Inspection Intervals
Fuel piping and connections should be replaced every 2
years.
TABLE 5. MVH-64VH/VHW MACHINE
INSPECTION
Daily Service
z
Check for leakage of fuel or oil.
ITEM
HOURS OF OPERATION
z
Remove soil and clean the bottom of compaction plate.
Check engine oil.
Damaged Parts
Every 8 hours (every day)
z
z
Check for loose screws including tightness. See Table 7
below (tightening torque ), for retightening:
Loose or Lost Screws Every 8 hours (every day)
Function of Controlling
Every 8 hours (every day)
System Part
TABLE 7.
TIGHTENING TORQUE (in. kg/cm) Diameter
Vibrator Oil Check
Every 100 hours
Every 300 hours
Material 6mm 8mm 10mm 12mm 14mm 16mm 18mm 20mm
4T
6-8T
11T
*
70
150
250
400
300
500
800
500
750
1,100 1,400 2,000
2,000 2,700 3,800
Vibrator Oil
Replacement
100
150
800
1,300
1,200
2,000 2,900 4,200 5,600
V-belt (clutch) Check Every 200 hours
100 (6mm) 300 ~ 350 (8mm) 650 ~ 700 (10mm)
* (In case counter-part is of aluminum)
(Threads in use with this machine are all right handed)
l
Material and quality of material is marked on each bolt,
and screw.
TABLE 6. ENGINE CHECK
(For details, see separate Engine Manual)
Engine Oil Replacement:
Item
Hours of Operation
1. Replace engine oil, in first 20 hours of operation and every
100 hours afterwards.
Leakage of oil or fuel
Every 8 hours (every day)
Every 8 hours (every day)
2. Oil may be drained more easily when it is warm after
operation (For more details, see separate HONDA Owner's
Manual).
Tightness of fastening threads
Every 8 hours (every
day)(Replenish to specified max.
level)
Engine oil check and replenishment
3. When changing the engine oil, the old oil can be drained by
removing the oil filler cap, and unscrewing the engine oil
drain plug located at the base of the engine (Figure 16).
At first 20 hours, then every 100
hours
Engine oil replenishment
Air cleaner cleaning
4. Remember to refill engine crankcase with the recommended
type of oil as listed in Table 4.
Every 50 hours
PAGE 20 — MVC-64VH/VHW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (03/01/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-64VH/VHW — MAINTENANCE
Changing Vibrator Oil
1. When changing the vibrator oil, remove the drain plug
(Figure 10), and simply tip the compactor to drain the oil.
Note that the oil will drain more easily while it is hot.
Remember to use only 10W-30 motor oil when replacing
vibrator oil.
Checking and Replacing the V-Belt and Clutch
1. After 200 hours of operation, remove the upper belt cover to
check theV-belt tension.Tension is proper if the belt bends
about 10 mm when depressed strongly with finger between
shafts. Loose or worn V-belts reduces power transmission
efficiency, causing weak compaction and reduces the life of
the belt itself.
Figure 16. Engine Oil Plug
Air Filter
1. The air filter element should be cleaned because a clogged
air cleaner can cause poor engine starting, lack of power
and shorten engine life substantially.
z
Replacing the V-belt
Remove the upper and lower belt covers. Engage an offset
wrench (13 mm) or the like to vibrator pulley (lower) fastening
bolt. Engage waste cloth or the like at midway ofV-belt on the left
side and while pulling it back strongly, rotate the offset wrench
clockwise so that theV-belt will come off.
2. To clean or replace air filter loosen the wing nut on the air
filter housing (Figure 17), remove the cover and take out air
filter cartridge. If only cleaning of the air filter is desired blow
through the air filter cartridge from the inside, moving a jet of
dry compressed air up and down until all dust is removed.
z
Reinstalling the V-belt
EngageV-belt to lower vibrator pulley and push theV-belt to left
side of upper clutch and, in the same manner as in removal,
rotate offset wrench clockwise so that the V-belt goes back on.
z
Checking Clutch
Check the clutch simultaneously withV-belt checking. With belt
removed, check outer drum of the clutch for seizure and "V"
groove for wear or damage with your eyes. Clean the "V" groove
as necessary. Wear of lining or shoe should be checked with
running check. If the shoe is worn, power transmission becomes
deficient and slipping will result.
Figure 17. Air Filter
WARNING - V-belt Hazard
Spark Plug
NEVER attempt to check theV-belt with the engine running.
Severe injury can occur if your hand (Figure 7) gets caught
betweentheV-beltandtheclutch.Alwaysusesafetygloves.
1. Remove and clean the spark plug (Figure 18).
2. Adjust the spark gap to 0.028 ~0.031 inch (0.6~0.7 mm).This
unit has electronic ignition, which requires no adjustments.
CAUTION - Vibration Check
Whenever the compactor's vibration becomes weak or lost
duringnormaloperationregardlessofoperationhours,check
theV-beltandclutchimmediately.
g Gap
MVC-64VH/VHW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (03/01/07) — PAGE 21
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-64VH/VHW — PREPARATION FOR LONG -TERM STORAGE
Compactor Storage
For storage of the compactor for over 30 days, the following
is required:
z
z
z
Drain the fuel tank completely or add STA-BIL to the
fuel.
Run the engine until the fuel in the injection system is
completely consumed.
Completely drain the oil from the engine crankcase and
follow procedures described in the HONDA engine
Owner's Manual for engine storage.
z
z
z
Completely drain the compactor's oil from the vibrating
case.
Clean entire plate compactor, especially the bottom plate
removing all dirt and foreign matter.
Cover plate compactor and engine with plastic covering
or equivalent and store in a clean, dry place.
l
PAGE 22 — MVC-64VH/VHW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (03/01/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-64VH/VHW — TROUBLESHOOTING (ENGINE)
Practically all breakdowns can be prevented by proper handling and maintenance inspections, but in the event of a
breakdown, please take a remedial action following the diagnosis based on the EngineTroubleshooting (Table 8) information
shown below and on the proceeding page. If the problem cannot be remedied, please leave the unit just as it is and consult
our company's business office or service plant.
TABLE 8. ENGINE TROUBLESHOOTING
SYMPTOM
POSSIBLE CAUSE
SOLUTION
Check gap, insulation or replace
spark plug.
Spark plug bridging?
Carbon deposit on spark plug?
Clean or replace spark plug.
Difficult to start, "fuel is available, but no
SPARK at spark plug".
Short circuit due to deficient spark plug
insulation?
Check spark plug insulation,
replace if worn.
Improper spark plug gap?
ON/OFF switch is shorted?
Ignition coil defective?
Set to proper gap.
Check switch wiring, replace
switch.
Replace ignition coil.
Set correct spark gap and clean
points.
Difficult to start, "fuel is available, and
SPARK is present at the spark plug".
Improper spark gap, points dirtry?
Condenser insulation worn or short
circuiting?
Replace condenser.
Replace defective spark plug
wiring.
Spark plug wire broken or short circuiting?
Wrong fuel type?
Flush fuel system, and replace
with correct type of fuel.
Difficult to start, "fuel is available, spark
is present and compression is normal"
Water or dust in fuel system?
Air cleaner dirty?
Flush fuel system.
Clean or replace air cleaner.
Re-seat valves.
Suction/exhaust valve stuck or protruded?
Replace piston rings and or
piston.
Piston ring and/or cylinder worn?
Difficult to start, "fuel is available, spark
is present and compression is low"
Cylinder head and/or spark plug not
tightened properly?
Torque cylinder head bolts and
spark plug.
Head gasket and/or spark plug gasket
damaged?
Replace head and spark plug
gaskets.
Fuel not available in fuel tank?
Fill with correct type of fuel.
Apply lubricant to loosen fuel
cock lever, replace if necessary.
Fuel cock does not open properly?
No fuel present at carburetor.
Fuel filter clogged?
Replace fuel filter.
Fuel tank cap breather hole clogged?
Air in fuel line?
Clean or replace fuel tank cap.
Bleed fuel line.
MVC-64VH/VHW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (03/01/07) — PAGE 23
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-64VH/VHW — TROUBLESHOOTING (ENGINE)
TABLE 8. ENGINE TROUBLESHOOTING (CONTINUED)
SYMPTOM
POSSIBLE CAUSE
Air cleaner not clean?
SOLUTION
Clean or replace air cleaner
Check float adjustment, re-build
carbureator.
Improper level in carburetor?
"Weak in power" compression is proper
and does not misfire.
Defective Spark plug?
Defective Spark plug?
Clean or replace spark plug.
Flush fuel system, and replace
with correct type of fuel.
Water in fuel system?
"Weak in power" compression is proper
but misfires.
Dirty spark plug?
Clean or replace spark plug.
Replace ignition coil.
Ignition coil defective?
Replace with correct type of
spark plug.
Spark plug heat value improper?
Engine overheats.
Correct type of fuel?
Replace with correct type of fuel
Clean cooling fins.
Cooling fins dirty?
Governor adjusted correctly?
Governor spring defective?
Adjust governor.
Replace governor spring.
Rotational speed fluctuates.
Check entire fuel system for leaks
or clogs.
Fuel flow restricted?
Recoil mechanism clogged with dust and Clean recoil assembly with soap
dirt?
and water.
Recoil starter malfunction.
Sprial spring loose?
Replace sprial spring.
l
PAGE 24 — MVC-64VH/VHW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (03/01/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-64VH/VHW — TROUBLESHOOTING (PLATE COMPACTOR)
Practically all breakdowns can be prevented by proper handling and maintenance inspections, but in the event of a
breakdown, please take a remedial action following the diagnosis based on the Compactor Troubleshooting (Table 9)
information shown below and on the proceeding page. If the problem cannot be remedied, please leave the unit just as it is
and consult our company's business office or service plant.
TABLE 9. PLATE COMPACTOR TROUBLESHOOTING
SYMPTOM
POSSIBLE CAUSE
Engine speed too low?
SOLUTION
Set engine speed to correct RPM.
Check or replace clutch.
Clutch slips?
Travel speed too low, and vibration is
weak.
V-belt slips?
Adjust or replace V-belt.
Excessive oil in vibrator?
Drain excess oil and fill to proper level.
Check eccentric, gears and counter
weights.
Malfunction in vibrator housing?
V-belt slips?
Clutch slips?
Replace V-belt.
Check clutch springs and shoes.
Does not travel forward.
Check vibrator housing (eccentric,
gears and counterweights)
Vibrator locked?
MVC-64VH/VHW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (03/01/07) — PAGE 25
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-64VH/VHW — EXPLANATION OF CODE IN REMARKS COLUMN
The following section explains the different symbols and remarks QTY. Column
used in the Parts section of this manual. Use the help numbers
found on the back page of the manual if there are any questions.
Numbers Used - Item quantity can be indicated by a number,
a blank entry, or A/R.
A/R (As Required) is generally used for hoses or other parts
that are sold in bulk and cut to length.
The contents and part numbers listed in the parts section are
A blank entry generally indicates that the item is not sold
separately. Other entries will be clarified in the “Remarks”
Column.
subject to change without notice. Multiquip does not
guarantee the availibility of the parts listed.
Sample Parts List:
REMARKS Column
NO. PART NO. PART NAME
QTY. REMARKS
Some of the most common notes found in the “Remarks”
Column are listed below. Other additional notes needed to
describe the item can also be shown.
1
2
2
3
4
12345
BOLT ....................... 1.... INCLUDES ITEMS W/
WASHER, 1/4 IN. ........... NOT SOLD SEPARATELY
WASHER, 3/8 IN. ....1.... MQ-45TONLY
HOSE .................... A/R.. MAKE LOCALLY
BEARING ................1.... S/N2345B AND ABOVE
*
*
*
12347
12348
12349
Assembly/Kit - All items on the parts list with the same unique
symbol will be included when this item is purchased.
Indicated by:
“INCLUDES ITEMS W/(unique symbol)”
NO. Column
Unique Symbols - All items with same unique symbol
Serial Number Break - Used to list an effective serial number
range where a particular part is used.
( , #,
+, %, or >) in the number column belong to the same
*
assembly or kit, which is indicated by a note in the “Remarks”
column.
Indicated by:
“S/N XXXXX AND BELOW”
“S/N XXXX AND ABOVE”
“S/N XXXX TO S/N XXX”
Duplicate Item Numbers - Duplicate numbers indicate
multiple part numbers are in effect for the same general item,
such as different size saw blade guards in use or a part that
has been updated on newer versions of the same machine.
Specific Model Number Use - Indicates that the part is used
only with the specific model number or model number variant
listed. It can also be used to show a part is NOT used on a
specific model or model number variant.
When ordering a part that has more
than one item number listed, check
the remarks column for help in
determining the proper part to order.
NOTE
Indicated by:
“XXXXX ONLY”
“NOT USED ON XXXX”
“Make/Obtain Locally” - Indicates that the part can be
purchased at any hardware shop or made out of available
items. Examples include battery cables, shims, and certain
washers and nuts.
PART NO. Column
l
Numbers Used - Part numbers can be indicated by a number,
a blank entry, orTBD.
TBD (To Be Determined) is generally used to show a part that
has not been assigned a formal part number at time of
publication.
“Not Sold Separately” - Indicates that an item cannot be
purchased as a separate item and is either part of an
assembly/kit that can be purchased, or is not available for
sale through Multiquip.
A blank entry generally indicates that the item is not sold
separately or is not sold by Multiquip. Other entries will be
clarified in the “Remarks” Column.
PAGE 26 — MVC-64VH/VHW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (03/01/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-64VH/VHW — SUGGESTED SPARE PARTS
MQ MIKASA MVC-64VH/VHW PLATE
COMPACTOR WITH HONDA GX120U1SM12
GASOLINE ENGINE
1 to 3 Units
Qty.
P/N
Description
3 .......... 070100312 ........... V-BELT
4 .......... 939010250 ........... SHOCK ABSORBER
3 .......... 9807956846 ......... SPARK PLUG
1 .......... 28462ZH8003 ...... ROPE, RECOIL STARTER
3 .......... 17210ZE0822 ....... ELEMENT, AIR CLEANER
1 .......... 17620ZH7023 ...... FUEL CAP
1 .......... 17672ZE2W01 ..... FUEL FILTER, FUEL TANK
MVC-64VH/VHW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (03/01/07) — PAGE 27
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-64VH/VHW — NAME PLATE AND DECALS
NAME PLATE AND DECALS
l
PAGE 28 — MVC-64VH/VHW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (03/01/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-64VH/VHW — NAME PLATE AND DECALS
NAMEPLATE AND DECALS
NO.
PART NO.
PART NAME
QTY.
REMARKS
1
2
3
4
5
6
7
PLATE, MODEL/SERIAL NUMBER ..................... 1 ................CONTACT PARTS DEPT.
920203290
920203989
920101410
920201580
920105070
920212320
DECAL, READ OWNERS MANUAL
DECAL, BELT GUARD WARNING
1 ................NPA-329
1 ................NPA-989
DECAL: MIKASA MARK 120X60 ......................... 1 ................WATERTANK
DECAL: MQ MARK 71X55 ................................... 1 ................MQ/WATERTANK
DECAL: MIKASA MARK 125MM ......................... 1 ................WATERTANK
DECAL:CAUTION REFUELING .......................... 1 ................NPA-1232
MVC-64VH/VHW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (03/01/07) — PAGE 29
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-64VH/VHW — MAIN BODY ASSY.
MAIN BODY ASSY.
29
11
52
27
53
55
53
54
54
14-1
14-2
14-3
19
55
31
32
33
20
23
22-2
25
18
41
21
56
22-1
26-3
26-2
26-1
51
16
28-3
28-2
2
28-1
17
4
47-2
l
49
45
46
50
5
47-1
6
l
12
13
3
7
6
5
1
PAGE 30 — MVC-64VH/VHW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (03/01/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-64VH/VHW — MAIN BODY ASSY.
MAIN BODY ASSY.
NO
1
2
3
4
5
6
7
11
12
13
14-1
14-2
14-3
16
17
18
19
20
PART NO
418118540
418216890
939010254
959404350
020310080
030210250
031110160
912212009
418457690
413436870
001220840
030208200
031108160
031108160
022710809
404418150
460446780
0320050150
952400130
001220825
030208200
070100312
418216470
001221035
030210250
031110160
418216480
001221053
030210250
031110160
418343420
020308060
030208200
031108160
418910070
404433430
952403450
001221020
030210250
413436720
001520845
020308060
418217060
416459340
009120407
416459320
418217050
PART NAME
VIBRATORY PLATE (570 X 350)
BASE
SHOCK ABSORBER D45-H41
EARTH WIRE
NUT M10
WASHER, LOCK M10
WASHER, FLAT M10
ENGINE, HONDA GX120U1SM12
BOLT, ENGINE
ENGINE NUT, REAR
BOLT 8X40T
WASHER, LOCK M8
WASHER, FLAT M8
WASHER, FLAT M8
NYLON NUT M8
SPACER 18X25X8 CLUTCH
CLUTCH ASSY.
QTY.
1
1
4
1
8
8
4
1
1
1
2
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
REMARKS
KEY
WASHER 9304
21
22-1
22-2
23
BOLT 8X25 H, SW
WASHER, LOCK
V-BELT RPF-3310
BELT COVER
BOLT 10X35 H, SW, PW
WASHER, LOCK
WASHER, FLAT
BELT COVER, IN.
BOLT 10X65 SW, PW
WASHER, LOCK
WASHER, FLAT
COVER SEAL, E/G
NUT M8
25
26-1
26-2
26-3
27
28-1
28-2
28-3
29
31
32
33
41
45
46
47-1
47-2
49
50
51
52#
53#
54#
55#
56#
WASHER, LOCK
WASHER, FLAT
VIB. PROOF HANDLE ASSY ................... 1 ................. INCLUDES ITEMS W/ #
RUBBER 20X32X28.5/52H
WASHER 11X35X4.5
BOLT 10X55 H,SW
WASHER, LOCK
RUBBER, HANDLE
SOCKET HEAD BOLT 8X45 T
NUT M8
GRIP, HANDLE
RUBBER, VIB. PROOF HANDLE
BOLT, SUNK HEAD 10X20 T
NUT, VIB. PROOF HANDLE
VIB. PROOF HANDLE
2
2
2
2
2
2
2
1
2
2
2
1
MVC-64VH/VHW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (03/01/07) — PAGE 31
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-64VH/VHW —VIBRATOR ASSY.
VIBRATOR ASSY.
PAGE 32 — MVC-64VH/VHW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (03/01/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-64VH/VHW —VIBRATOR ASSY.
VIBRATOR ASSY.
NO
61
62
63
64
65
66
67
68
69
70
71
72
72
73
74
75
77
78
79
PART NO
418117730
001221445
030214350
031114260
418456950
060403020
418456960
418456970
002400820
418456990
418343400
040306307
040406307
418456980
951401920
952403450
002211030
953400270
953405260
PART NAME
VIBRATING CASE
BOLT 14X45 T
QTY.
1
4
4
4
1
1
1
2
8
1
1
2
2
1
1
1
REMARKS
WASHER, LOCK M14
WASHER, FLAT M14
CASE COVER/PULLEY
OIL SEAL TC-30458
CASE COVER/SHUT-OFF
PACKING
BOLT 8X20 SW, PW
COVER SEAL, VIB.
ECC. ROTOR SHAFT
BEARING 6307C3
BEARING 6307C4
PULLEY, VIB.
KEY 7X7X30
WASHER 11X35X4.5
BOLT 10X30 H, SW
PLUG 1/4X14 10L
PACKING
1
1
1
MVC-64VH/VHW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (03/01/07) — PAGE 33
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-64VH/VHW —WATERTANK ASSY.
WATER TANK ASSY.
PAGE 34 — MVC-64VH/VHW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (03/01/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-64VH/VHW —WATERTANK ASSY.
WATER TANK ASSY.
NO
91
92
PART NO
418118580
002211025
418910020
418910030
954300342
001241030
033910010
022910180
954403241
959403790
416338940
418343430
001220825
031108160
020308060
418457010
PART NAME
QTY.
REMARKS
HOOK ........................................................ 1 ................. REPLACES 418216510
BOLT 10X25 H, SW
3
101
101
102
103
104
105
107
108
110
111
112
113
114
115
WATERTANK, ORANGE ........................... 1 ................. INCLUDES ITEM W/
WATER TANK, WHITE ............................... 1 ................. INCLUDES ITEM W/
CAP, WATER TANK
BOLT 10X30 U
WASHER 10.5X21X2 SUS.
NYLON NUT M10 SUS.
COCK PT1/4, BH-1211 AL.
NUT PS-1/4
PIPE HOLDER, L
SPRINKLING PIPE
BOLT 8X25 T
*
*
1
1
2
1
1
1
1
1
1
2
1
1
*
*
*
*
WASHER, FLAT M8
NUT M8
RUBBER CAP
MVC-64VH/VHW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (03/01/07) — PAGE 35
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX120U1SM12 ENGINE — CYLINDER HEAD ASSY.
CYLINDER HEAD ASSY.
l
PAGE 36 — MVC-64VH/VHW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (03/01/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX120U1SM12 ENGINE — CYLINDER HEAD ASSY.
CYLINDER HEAD ASSY.
NO.
PART NO.
PART NAME
QTY.
REMARKS
1
12210ZH7405
12204ZE1306
12205ZE1315
12216ZE5300
12251ZH7800
12310ZE1020
12391ZE1000
15721ZH8000
90013883000
90043ZE1020
90047ZE1000
9430110160
CYLINDER HEAD ..................................................1.............. INCLUDES ITEMS W/
*
2
3
GUIDE, VALVE (OS) OPTIONAL
GUIDE, EX. VALVE (OS) OPTIONAL ................... 1.............. INCLUDES ITEMS W/+
CLIP, VALVE GUIDE
GASKET, CYLINDER HEAD
COVER, HEAD
GASKET, CYLINDER HEAD COVER
TUBE, BREATHER
BOLT, FLANGE 6X12 (CT200)
BOLT, STUD 6X109
BOLT, STUD 8X32
1
*
*
4 +
1
1
1
1
1
4
2
2
2
4
1
*
5
6
7
8
9
10
11
12
14
15
PIN, A, DOWEL 10X16
BOLT, FLANGE 8X55
SPARK PLUG BPR6ES (NGK)
957230805500
9807956846
MVC-64VH/VHW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (03/01/07) — PAGE 37
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX120U1SM12 ENGINE — CYLINDER BARREL ASSY.
CYLINDER BARREL ASSY.
4
3
6
6
7
10
12
5
16
4
18
20
17
2
20
1
8
19
13
9
11
14
l
11
9
PAGE 38 — MVC-64VH/VHW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (03/01/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX120U1SM12 ENGINE — CYLINDER BARREL ASSY.
CYLINDER BARREL ASSY.
NO.
1
2
PART NO.
PART NAME
QTY.
REMARKS
12000ZH7425
15510ZE1033
16510ZE1000
16511ZE1000
16512ZE1000
16513ZE1000
16531ZE1000
16541ZE1000
90131ZE1000
90451ZE1000
90601ZE1000
90602ZE1000
91001878003
91202ZE6013
91353671004
9405010000
BARREL ASSY., CYLINDER ......................1 ............ INCLUDES ITEMS W/
*
#
SWITCH ASSY., OIL LEVEL
GOVERNOR ASSY. ....................................1 ............ INCLUDES ITEMS W/
1
3
4#
5#
6#
7
8
9
WEIGHT, GOVERNOR
HOLDER, GOVERNORWEIGHT
PIN, GOVERNOR WEIGHT
SLIDER, GOVERNOR
SHAFT, GOVERNOR ARM
BOLT, DRAIN PLUG
WASHER, THRUST 6mm
WASHER, DRAIN PLUG 10.2mm
CLIP, GOVERNOR HOLDER
BEARING, RADIAL BALL 62/22
OIL SEAL 22X35X6
O- RING 14mm
NUT, FLANGE 10mm
WASHER, PLAIN 6mm
PIN, LOCK 8mm
BOLT, FLANGE 6X12
2
1
2
1
1
2
1
2
1
1
1
1
1
2
1
2
10
11
12
13
14
16
17
18
19
20
*
*
9410106800
9425108000
957010601200
MVC-64VH/VHW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (03/01/07) — PAGE 39
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX120U1SM12 ENGINE — CRANKCASE COVER ASSY.
CRANKCASE COVER ASSY.
11
11
11
11
5
7
16
14
16
7
13
1
6
3
l
PAGE 40 — MVC-64VH/VHW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (03/01/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX120U1SM12 ENGINE — CRANKCASE COVER ASSY.
CRANKCASE COVER ASSY.
NO.
1
3
PART NO.
PART NAME
QTY.
REMARKS
11300ZE0634
11381ZH7800
15600ZE1003
15600ZG4003
15625ZE1003
90015883000
91001878003
91203ZE0013
9430108140
COVER ASSY., CRANKCASE ................................ 1 ..............INCLUDES ITEMS W/
*
GASKET, CRANKCASE
CAP ASSY., OIL FILLER......................................... 1 ..............INCLUDES ITEMS W/
CAP ASSY., OIL FILLER......................................... 1 ..............INCLUDES ITEMS W/+
PACKING, OIL FILLER CAP
BOLT, FLANGE 6X28
BEARING, RADIAL 62/22
OIL SEAL 22X41X6
1
5
#
6
7#
+
2
7
1
1
2
11
13
14
16
*
*
DOWEL PIN 8X14
MVC-64VH/VHW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (03/01/07) — PAGE 41
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX120U1SM12 ENGINE — CRANKSHAFT ASSY.
CRANKSHAFT ASSY.
1
l
PAGE 42 — MVC-64VH/VHW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (03/01/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX120U1SM12 ENGINE — CRANKSHAFT ASSY.
CRANKSHAFT ASSY.
NO.
1
PART NO.
13310ZE0000
PART NAME
CRANKSHAFT
QTY.
1
REMARKS
MVC-64VH/VHW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (03/01/07) — PAGE 43
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX120U1SM12 ENGINE — PISTON/CONNECTING ROD ASSY.
PISTON/CONNECTING RODASSY.
l
PAGE 44 — MVC-64VH/VHW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (03/01/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX120U1SM12 ENGINE — PISTON/CONNECTING ROD ASSY.
PISTON/CONNECTING RODASSY.
NO.
1
1
1
1
2
2
2
2
3
4
4
5
*
6
PART NO.
PART NAME
QTY. REMARKS
13010ZH7003
13011ZH7003
13012ZH7003
13013ZH7003
13101ZH7010
13102ZH7010
13103ZH7010
13104ZH7010
13111ZE0000
13200ZE0000
13200ZE0000
90001ZE1000
90551ZE0000
RING SET, PISTON (STANDARD)
RING SET, PISTON (OS 0.25), OPTIONAL
RING SET, PISTON (OS 0.50) , OPTIONAL
RING SET, PISTON (OS 0.75), OPTIONAL
PISTON, STANDARD
1
1
1
1
1
1
1
1
1
PISTON, OS 0.25
PISTON, OS 0.50
PISTON, 0.75
PIN, PISTON
ROD ASSY, CONNECTING (UNDER SIZE) .... 1 ...... INCLUDES ITEMS W/
ROD ASSY., CONNECTING ............................ 1 ...... INCLUDES ITEMS W/
BOLT, CONNECTING ROD
CLIP, PISTON PIN 13MM
*
*
2
2
MVC-64VH/VHW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (03/01/07) — PAGE 45
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX120U1SM12 ENGINE — CAMSHAFT ASSY.
CAMSHAFT ASSY.
2
9
10
12
13
7
5
8
1
3
10
11
15
4
6
16
3
5
15
14
6
4
16
l
PAGE 46 — MVC-64VH/VHW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (03/01/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX120U1SM12 ENGINE — CAMSHAFT ASSY.
CAMSHAFT ASSY.
NO.
1
2
3
4
5
6
7
*
8
9
10
11
12
13
14
15
16
PART NO.
PART NAME
SEAL, VALVE STEM ........................................ 1
CAMSHAFT ASSY. .......................................... 1.............INCLUDES ITEMS W/
QTY.
REMARKS
12209ZH8003
14100ZE0812
14410ZE0010
14431ZE1000
14441ZE1010
14451ZE1013
14568ZE1000
14711ZF0000
14721ZF0000
14751ZF1000
14771ZE1000
14773ZE1000
14781ZE1000
14791ZE0010
90012ZE0010
90206ZE1000
*
ROD, PUSH
2
2
2
2
1
1
1
2
1
1
1
1
2
2
ARM, VALVE ROCKER
LIFTER, VALVE
PIVOT, ROCKER ARM
SPRING, WEIGHT RETURN
VALVE, IN.
VALVE, EX.
SPRING, VALVE
RETAINER, IN. VALVE SPRING
RETAINER, EX. VALVE SPRING
ROTATOR, VALVE
PLATE, PUSH ROD GUIDE
BOLT, PIVOT 8MM
NUT, PIVOT ADJ.
MVC-64VH/VHW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (03/01/07) — PAGE 47
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX120U1SM12 ENGINE — RECOIL STARTER ASSY.
RECOIL STARTER ASSY.
4
9
11
7
3
12
9
5
6
4
1
10
8
2
13
l
PAGE 48 — MVC-64VH/VHW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (03/01/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX120U1SM12 ENGINE — RECOIL STARTER ASSY.
RECOIL STARTER ASSY.
NO.
PART NO.
PART NAME
QTY.
REMARKS
1
28400ZH8023ZB
28410ZH8003ZB
28421ZH8801
28422ZH8801
28431ZH8801
28433ZH8801
28441ZH8801
28442ZH8803
28443ZH8001
28461ZH8003
28462ZH8003
90003ZH8001
9008ZE2003
STARTER ASSY., RECOIL *NH1* .........................1.............. INCLUDES ITEMS W/
*
2
CASE, RECOIL STARTER *NH1*
REEL, RECOIL STARTER
RATCHET, STARTER
PLATE, FRICTION
GUIDE, RATCHET
SPRING, FRICTION
SPRING, RECOIL STARTER
SPRING, RETURN
GRIP, STARTER
ROPE, RECOIL STARTER
SCREW, SETTING
BOLT, FLANGE 6X10
1
1
2
1
1
1
1
2
1
1
1
3
*
3
*
4
*
5
*
6
*
7
*
8
*
9
*
10
*
11
*
12
*
13
MVC-64VH/VHW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (03/01/07) — PAGE 49
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX120U1SM12 ENGINE — FAN COVER ASSY.
FAN COVER ASSY.
l
PAGE 50 — MVC-64VH/VHW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (03/01/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX120U1SM12 ENGINE — FAN COVER ASSY.
FAN COVER ASSY.
NO.
1
2
3
5
6
8
10
11
13
14
16
PART NO.
PART NAME
GROMMET, ADJUSTING COVER
COVER, FAN *NH1*
PLATE, SIDE (OIL ALERT)
CLIP, HARNESS
SHROUD
QTY.
REMARKS
11347371300
19610ZE0000ZE
19611ZH7810
90601ZH7013
19630ZH7000
34150ZH7003
36100ZF6P81
36101ZE1010
90013883000
90022888010
95 7010600800
1
1
1
1
1
1
1
1
6
1
1
ALERT UNIT, OIL
SWITCH ASSEMBLY, ENGINE STOP
WIRE, STOP SWITCH 370MM
BOLT, FLANGE 6X12 (CT200)
BOLT, FLANGE 6X20(CT200)
BOLT, FLANGE 6X8
MVC-64VH/VHW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (03/01/07) — PAGE 51
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX120U1SM12 ENGINE — CARBURETOR ASSY.
CARBURETOR ASSY.
28
23
24
1
25
14
13
33
1
19
31
22
10
8
1
12
16
5
26
11
32
15
2
9
3
1
6
4
1
1
7
l
PAGE 52 — MVC-64VH/VHW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (03/01/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX120U1SM12 ENGINE — CARBURETOR ASSY.
CARBURETOR ASSY.
NO.
PART NO.
PART NAME
QTY.
REMARKS
1
2
3
#
16010ZE1812
16011ZE0005
16013ZE0005
16015ZE0831
16016ZH7W01
16024ZE1811
16028ZE0005
16044ZE0005
16100ZH7W51
16124ZE0005
16166ZH7W50
16173001004
16211ZE0000
16212ZH7800
16220ZE1020
16221ZH8801
16610ZE1000
16953ZE1812
16954ZE1812
16956ZE1811
16957ZE1812
16967ZE0811
93500030061H
9430520122
GASKET SET
VALVE SET, FLOAT
FLOAT SET
1
1
1
*
*
*
4
5
FLOAT CHAMBER SET.................................... 1.............INCLUDES ITEMS W/
#
*
SCREW SET, PILOT
SCREW SET, DRAIN
SCREW SET B
1
1
1
1
*
6
7
#
*
*
8
9
CHOKE SET
*
CARBURETOR ASSY., BE60B B ..................... 1.............INCLUDES ITEMS W/
SCREW, THROTTLE STOP
NOZZLE, MAIN
*
10
11
12
13
14
15
16
19
22
23
24
25
26
28
1
1
1
1
1
1
1
*
*
*
PACKING, CUP
INSULATOR, CARBURETOR
PACKING, INSULATOR
SPACER, CARBURETOR
GASKET, CARBURETOR
LEVER, CHOKE (STANDARD) ......................... 1.............INCLUDES ITEMS W/+
LEVER,VALVE
PLATE, LEVER SETTING
SPRING, VALVE LEVER
GASKET, VALVE
CUP, FUEL STRAINER
SCREW, PAN (3 X 6)
PIN, SPRING (2 X 12)
JET, MAIN (#60)
1
1
1
1
1
2
1
1
1
*
*
*
*
*
*
31+
32
33
*
99101ZH80600
99204ZE00350
*
JET, SET, PILOT (#35)
MVC-64VH/VHW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (03/01/07) — PAGE 53
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX120U1SM12 ENGINE — AIR CLEANER ASSY.
AIR CLEANER ASSY.
l
PAGE 54 — MVC-64VH/VHW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (03/01/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX120U1SM12 ENGINE — AIR CLEANER ASSY.
AIR CLEANER ASSY.
NO.
2
PART NO.
PART NAME
QTY.
REMARKS
16271ZE1000
17210ZE0822
17218ZE0821
17230ZE0820
17232891000
17235ZE1831
17238ZE0010
17239ZE1000
17410ZE0030
90325044000
9405006000
GASKET, ELBOW
1
3
CLEANER ELEMENT ....................................... 1 ............INCLUDES ITEMS W/
ELEMENT OUTER
COVER, AIR CLEANER
GROMMET, AIR CLEANER
NOSE, SILENCER
COLLAR, AIR CLEANER
COLLAR B, AIR CLEANER
ELBOW, AIR CLEANER ................................... 1.............INCLUDES ITEMS W/
WINGNUT, TOOL BOX SETTING
NUT, FLANGE 6MM
#
4
5
6
7
8
9
#
1
1
1
1
2
1
#
*
*
10
11
13
15
*
2
2
1
957010602000
BOLT, FLANGE 6X20
MVC-64VH/VHW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (03/01/07) — PAGE 55
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX120U1SM12 ENGINE — MUFFLER ASSY.
MUFFLER ASSY.
17
17
4
14
6
17
15
15
17
3
20
24
7
l
8
16
PAGE 56 — MVC-64VH/VHW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (03/01/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX120U1SM12 ENGINE — MUFFLER ASSY.
MUFFLER ASSY.
NO.
3
4
6
7
PART NO.
PART NAME
QTY.
REMARKS
18310ZH8810
18320ZF1H01
18340ZE1010
18355ZE1000
18381ZH8800
18522ZE1000
90002ZG0003
90016ZE1000
90050ZE1000
90055ZE1000
94001080000S
MUFFLER
1
1
1
1
1
1
2
1
4
1
2
PROTECTOR, MUFFLER
DEFLECTOR
ARRESTER, SPARK
GASKET, MUFFLER
GUIDE, MUFFLER
SCREW, TAPPING 4X8
BOLT, FLANGE 6 X 13
SCREW, TAPPING 5X8
SCREW, TAPPING 4X6
NUT, HEX. 8MM
8
14
15
16
17
20
24
MVC-64VH/VHW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (03/01/07) — PAGE 57
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX120U1SM12 ENGINE — FUELTANK ASSY.
FUEL TANK ASSY.
10
11
12
9
14
23
19
17
22
23
7
l
3
PAGE 58 — MVC-64VH/VHW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (03/01/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX120U1SM12 ENGINE — FUELTANK ASSY.
FUEL TANK ASSY.
NO.
3
7
9
10
PART NO.
PART NAME
RUBBER, SUPPORTER 107MM
JOINT, FUEL TANK
TANK, FUEL *NH1* (BLACK)
CAP, FUEL FILLER ..................................... 1 .......... INCLUDES ITEMS W/
GASKET, FUEL FILLER CAP
FUEL FILTER
BOLT, FLANGE 6X29
O- RING 14MM
NUT, FLANGE 6MM
BULK HOSE, FUEL 4.5X140
BULK HOSE, FUEL 4.5X1000
CLIP, TUBE (B8)
QTY.
REMARKS
16854ZH8000
16955ZE1000
17510ZE0020ZD
17620ZH7023
17631ZH7003
17672ZE2W01
90004ZH7003
91353671004
9405006000
1
1
1
*
11
12
1
1
1
1
2
1
1
2
*
14
17
19
22
22
23
950014514040
950014500160M
9500202080
MVC-64VH/VHW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (03/01/07) — PAGE 59
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX120U1SM12 ENGINE — FLYWHEEL ASSY.
FLYWHEEL ASSY.
5
1
4
2
7
l
PAGE 60 — MVC-64VH/VHW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (03/01/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX120U1SM12 ENGINE — FLYWHEEL ASSY.
FLYWHEEL ASSY.
NO.
1
2
4
5
PART NO.
PART NAME
KEY, SPECIAL WOODRUFF 25X18
FAN, COOLING
PULLEY, STARTER
FLYWHEEL
NUT, SPECIAL 14MM
QTY.
REMARKS
13331357000
19511ZE0000
28451ZH7801
31100ZE0010
90201878003
1
1
1
1
1
7
MVC-64VH/VHW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (03/01/07) — PAGE 61
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX120U1SM12 ENGINE — IGNITION COIL ASSY.
IGNITION COIL ASSY.
l
PAGE 62 — MVC-64VH/VHW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (03/01/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX120U1SM12 ENGINE — IGNITION COIL ASSY.
IGNITION COIL ASSY.
NO.
1
2
PART NO.
PART NAME
QTY.
REMARKS
30500ZE1063
30700ZE1013
90121952000
COIL ASSY., IGNITION
CAP ASSY., NOISE SUPPRESSOR
BOLT, FLANGE 6X25
1
1
2
8
MVC-64VH/VHW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (03/01/07) — PAGE 63
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX120U1SM12 ENGINE — CONTROL ASSY.
CONTROL ASSY.
32
24
6
3
10
30
21
28
11
14
13
30
20
21
31
8
12
27
16
29
31
15
29
15
23
19
26
18
l
PAGE 64 — MVC-64VH/VHW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (03/01/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX120U1SM12 ENGINE — CONTROL ASSY.
CONTROL ASSY.
NO.
3
6
PART NO.
PART NAME
QTY.
REMARKS
16500ZK7U50
16551ZE0010
16555ZE0000
16561ZE0020
16562ZE0020
16571ZH7000
16574ZE1000
16575ZH8000
16576891000
16578ZE1000
16580ZH7810
16584883300
16592ZE1810
16594883010
90013883000
90015ZE5010
93500050250H
90022888010
90114SA0000
90605230000
93500040060H
93500050160A
9405006000
CONTROL ASSY. ...................................... 1 ............ INCLUDES ITEMS W/
#
ARM, GOVERNOR
ROD, GOVERNOR
SPRING, GOVERNOR
SPRING,THROTTLE RETURN
LEVER, CONTROL
SPRING, LEVER
WASHER, CONTROL LEVER
HOLDER, CABLE
SPACER, CONTROL LEVER
BASE CONTROL
SPRING, CONTROL ADJUSTING
SPRING, CABLE RETURN
HOLDER, WIRE
BOLT, FLANGE 6X12 (CT200)
BOLT, GOVERNOR ARM
SCREW, PAN 5X25
BOLT, FLANGE 6X20 (CT200)
NUT, SELF- LOCK 6MM
CIRCLIP, 5 MM
SCREW 4X6
SCREW, PAN 5X16
NUT, FLANGE 6MM
1
1
1
1
1
1
1
2
1
1
1
1
2
1
1
1
1
1
2
2
2
1
8
10
11
12
13
14
15
16
18
19
20
21
23
24
26
27
28
#
#
#
#
#
#
#
#
#
#
#
29#
30
31
32
#
#
MVC-64VH/VHW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (03/01/07) — PAGE 65
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX120U1SM12 ENGINE — LABELS ASSY.
LABELS ASSY.
2
4
5
3
l
PAGE 66 — MVC-64VH/VHW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (03/01/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX120U1SM12 ENGINE — LABELS ASSY.
LABELS ASSY.
NO.
2
3
4
5
PART NO.
PART NAME
MARK, OPERATOR CAUTION
EMBLEM
MARK, CHOKE
MARK, THROTTLE INDICATION
QTY.
REMARKS
87521ZH7000
87521ZH7030
87528ZH7000
87532ZH7000
1
1
1
1
MVC-64VH/VHW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (03/01/07) — PAGE 67
Download from Www.Somanuals.com. All Manuals Search And Download.
Effective: February 22, 2006
TERMS AND CONDITIONS OF SALE — PARTS
PAYMENT TERMS
5. Partsmustbeinnewandresalablecon- Multiquipreservestherighttoquoteandsell
dition,intheoriginalMultiquippackage(if directtoGovernmentagencies,andtoOriginal
any), and with Multiquip part numbers Equipment Manufacturer accounts who use
Terms of payment for parts are net 30 days.
FREIGHTPOLICY
clearlymarked.
our products as integral parts of their own
products.
All parts orders will be shipped collect or
prepaidwiththechargesaddedtotheinvoice.
All shipments are F.O.B. point of origin.
Multiquip’sresponsibilityceaseswhenasigned
manifesthasbeenobtainedfromthecarrier,
andanyclaimforshortageordamagemustbe
settledbetweentheconsigneeandthecarrier.
6. Thefollowingitemsarenotreturnable:
SPECIALEXPEDITINGSERVICE
a. Obsolete parts. (If an item is in the
price book and shows as being re- A$35.00surchargewillbeaddedtotheinvoice
placedbyanotheritem,itisobsolete.) forspecialhandlingincludingbusshipments,
insuredparcelpostorincaseswhereMultiquip
mustpersonallydeliverthepartstothecarrier.
(such as gaskets, seals, “O” rings,
b. Any parts with a limited shelf life
andotherrubberparts)thatwerepur- LIMITATIONSOFSELLER’SLIABILITY
MINIMUMORDER
chasedmorethansixmonthspriorto
thereturndate.
Multiquip shall not be liable hereunder for
damagesinexcessofthepurchasepriceofthe
TheminimumchargeforordersfromMultiquip
is $15.00 net. Customers will be asked for
instructionsregardinghandlingofordersnot
meetingthisrequirement.
c. Anylineitemwithanextendeddealer item with respect to which damages are
netpriceoflessthan$5.00.
claimed, and in no event shall Multiquip be
liable for loss of profit or good will or for any
otherspecial,consequentialorincidentaldam-
ages.
d. Special order items.
RETURNEDGOODSPOLICY
e. Electricalcomponents.
f. Paint,chemicals,andlubricants.
g. Decalsandpaperproducts.
h. Itemspurchasedinkits.
Returnshipmentswillbeacceptedandcredit
willbeallowed,subjecttothefollowingprovi-
sions:
LIMITATIONOFWARRANTIES
Nowarranties,expressorimplied,aremade
in connection with the sale of parts or trade
accessoriesnorastoanyenginenotmanufac-
tured by Multiquip. Such warranties made in
connectionwiththesaleofnew,completeunits
are made exclusively by a statement of war-
rantypackagedwithsuchunits,andMultiquip
neitherassumesnorauthorizesanypersonto
assume for it any other obligation or liability
whatever in connection with the sale of its
products.Apartfromsuchwrittenstatementof
warranty, there are no warranties, express,
impliedorstatutory,whichextendbeyondthe
descriptionoftheproductsonthefacehereof.
1. AReturnedMaterialAuthorizationmust
be approved by Multiquip prior to ship-
ment.
7. Thesenderwillbenotifiedofanymaterial
receivedthatisnotacceptable.
2. ToobtainaReturnMaterialAuthorization,
alistmustbeprovidedtoMultiquipParts
Salesthatdefinesitemnumbers,quanti-
ties, and descriptions of the items to be
returned.
8. Suchmaterialwillbeheldforfiveworking
days from notification, pending instruc-
tions.Ifareplyisnotreceivedwithinfive
days,thematerialwillbereturnedtothe
senderathisexpense.
a. Thepartsnumbersanddescriptions
must match the current parts price
list.
9. Creditonreturnedpartswillbeissuedat
dealer net price at time of the original
purchase,lessa15%restockingcharge.
b. The list must be typed or computer
generated.
10. In cases where an item is accepted, for
which the original purchase document
can not be determined, the price will be
basedonthelistpricethatwaseffective
twelvemonthspriortotheRMAdate.
l
c. The list must state the reason(s) for
thereturn.
d. The list must reference the sales
order(s)orinvoice(s)underwhichthe
itemswereoriginallypurchased.
11. Credit issued will be applied to future
purchasesonly.
e. The list must include the name and
phonenumberofthepersonrequest-
ingtheRMA.
PRICINGANDREBATES
Prices are subject to change without prior
notice.Pricechangesareeffectiveonaspe-
cificdateandallordersreceivedonorafterthat
datewillbebilledattherevisedprice.Rebates
3. AcopyoftheReturnMaterialAuthoriza-
tionmustaccompanythereturnshipment.
4. Freight is at the sender’s expense. All forpricedeclinesandaddedchargesforprice
partsmustbereturnedfreightprepaidto increaseswillnotbemadeforstockonhand
Multiquip’sdesignatedreceivingpoint.
atthetimeofanypricechange.
PAGE 68 — MVC-64VH/VHW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (03/01/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE PAGE
MVC-64VH/VHW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (03/01/07) — PAGE 69
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION AND PARTS MANUAL
HERE'S HOW TO GET HELP
PLEASE HAVETHE MODEL AND SERIAL
NUMBER ON-HANDWHEN CALLING
UNITED STATES
Multiquip Corporate Office
18910 Wilmington Ave.
Carson, CA 90746
MQ Parts Department
800-427-1244
Tel. (800) 421-1244
Fax (800) 537-3927
Fax:800-672-7877
Fax:310-637-3284
310-537-3700
Contact: [email protected]
Mayco Parts
800-306-2926
310-537-3700
Warranty Department
800-421-1244, Ext. 279 Fax:310-537-1173
310-537-3700, Ext. 279
Fax:800-672-7877
Fax:310-637-3284
Service Department
800-421-1244
Technical Assistance
800-478-1244
Fax:310-537-4259
Fax:310-631-5032
310-537-3700
MEXICO
MQ Cipsa
UNITED KINGDOM
Multiquip (UK) Limited Head Office
Hanover Mill, Fitzroy Street,
Ashton-under-Lyne,
Carr. Fed. Mexico-Puebla KM 126.5
Momoxpan, Cholula, Puebla72760Mexico
Tel: (52) 222-225-9900
Fax: (52) 222-285-0420
Tel: 0161 339 2223
Fax: 0161 339 3226
Lancashire OL7 0TL
CANADA
Multiquip
BRAZIL
Multiquip
4110IndustrielBoul.
Laval, Quebec, Canada H7L 6V3
Tel: (450) 625-2244
Fax: (450) 625-8664
Av. Evandro Lins e Silva, 840 - grupo 505 Tel: 011-55-21-3433-9055
Barra de Tijuca - Rio de Janeiro Fax: 011-55-21-3433-9055
© COPYRIGHT 2007, MULTIQUIP INC.
Multiquip Inc, the MQ logo and the Mikasa logo are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without written permission. All other
trademarks are the property of their respective owners and used with permission.
This manual MUST accompany the equipment at all times. This manual is considered a permanent part of the equipment and should remain with the unit if resold.
The information and specifications included in this publication were in effect at the time of approval for printing. Illustrations are based on the MVC-64VH/VHW Plate
Compactor. Illustrations, descriptions, references and technical data contained in this manual are for guidance only and may not be considered as binding. Multiquip Inc.
reserves the right to discontinue or change specifications, design or the information published in this publication at any time without notice and without incurring any
obligations.
Your Local Dealer is:
Download from Www.Somanuals.com. All Manuals Search And Download.
|