PARTS AND OPERATION MANUAL
PLASTER/MORTAR MIXERS
EM-900S
EM-900P
Revision #7 (06/26/01)
MULTIQUIPINC.
PARTS DEPARTMENT:
18910 WILMINGTON AVE.
800-427-1244
CARSON, CALIFORNIA 90746 FAX: 800-672-7877
310-537-3700
800-421-1244
SERVICE DEPARTMENT:
800-478-1244
FAX:310-537-3927
FAX:310-537-4259
Atlanta • Boise • Dallas • Houston • Newark
Montreal, Canada • Manchester, UK
Rio De Janiero, Brazil • Guadalajara, Mexico
Download from Www.Somanuals.com. All Manuals Search And Download.
PAGE 2 — ESSICK EM-900S & 900P — PARTS & OPERATION MANUAL — REV. #7 (06/26/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
HERE'S HOW TO GET HELP
PLEASE HAVE THE MODEL AND SERIAL NUMBER
ON-HAND WHEN CALLING
PARTS DEPARTMENT
800-427-1244 or 310-537-3700
FAX: 800-672-7877 or 310-637-3284
SERVICE DEPARTMENT/TECHNICAL ASSISTANCE
800-478-1244 or 310-537-3700
FAX: 310- 537-4259
WARRANTY DEPARTMENT
888-661-4279, or 310-661-4279
FAX: 310- 537-1173
MAIN
800-421-1244 or 310-537-3700
FAX: 310-537-3927
ESSICK EM-900S & 900P — PARTS & OPERATION MANUAL — REV. #7 (06/26/01) — PAGE 3
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
Here's How To Get Help .......................................... 3
Table Of Contents ................................................... 4
Parts Ordering Procedures ..................................... 5
Rules for Safe Operation & Safety Decals .............. 6
Warranty.................................................................. 7
ESSICK — 900S & 900P
Operations ......................................................... 8-11
Specifications ........................................................ 12
Explanation Of Codes In Remarks Column .......... 14
Suggested Spare Parts ......................................... 15
Drum Head Assembly ...................................... 16-17
Paddle Shaft Assembly .................................... 18-19
Steel Drum (S) ................................................. 20-21
Polyethylene Drum (P) ..................................... 22-23
Gas Engines, Pulleys & Cab Assembly............ 24-25
Electric Motor & Pulleys ................................... 26-27
Axle & Wheel Group ......................................... 28-29
Terms and Conditions Of Sale — Parts ................ 30
NOTE: Specification and part number
are subject to change without notice.
PAGE 4 — ESSICK EM-900S & 900P — PARTS & OPERATION MANUAL — REV. #7 (06/26/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS ORDERING PROCEDURES
Dealer account number
Dealer name and address
Shipping address (if different than billing address)
Return fax number
Applicable model number
Quantity, part number and description of each part
Specify preferred method of shipment:
UPS Ground
•
UPS Second Day or Third Day*
•
UPS Next Day*
•
Federal Express Priority One (please provide us with your Federal
Express account number)*
•
Airborne Express*
•
Truck or parcel post
•
*Normally shipped the same day the order is received, if prior to 2PM west coast time.
Earn Extra Discounts when
you order by FAX!
All parts orders which include complete part numbers
and are received by fax qualify for the following extra
discounts:
Number of
line items ordered
Additional Discount
1-9 items
3%
10+ items**
5%
Get special freight allowances
when you order 10 or more
line items via FAX!**
Now! Direct TOLL-FREE access
to our Parts Department!
UPS Ground Service at no charge for freight
PS Third Day Service at one-half of actual freight cost
No other allowances on freight shipped by any other carrier.
Toll-free nationwide:
800-421-1244
**Common nuts, bolts and washers (all items under $1.00 list price)
do not count towards the 10+ line items.
Toll-free FAX:
*DISCOUNTS ARE SUBJECT TO CHANGE*
800/6-PARTS-7 • 800-672-7877
Fax order discount and UPS special programs revised June 1, 1995
ESSICK EM-900S & 900P — PARTS & OPERATION MANUAL — REV. #7 (06/26/01) — PAGE 5
Download from Www.Somanuals.com. All Manuals Search And Download.
RULES FOR SAFE OPERATION & SAFETY DECALS
ꢀ
Do not operate or service this equipment
ꢀ
When towing, an adequate safety chain
before reading the operating and
maintenance instructions manual or serious
injury may result.
must be fastened to the frame, refer to page 9.
ꢀ
Keep all inexperienced and unauthorized
people away from the equipment at all times.
ꢀ
Do not operate this equipment unless all
ꢀ
Unauthorized equipment modifications will
guards and safety devices are attached and
in place.
void all warranties.
ꢀ
Check all fasteners periodically for
ꢀ
Stop the engine when leaving the
tightness. Also check towing tongue bolt, lock
nut and wheel lug nuts for wear.
equipment.
ꢀ
Block the unit when leaving or when using
ꢀ
Wear safety glasses at all times when
on a slope
working around machinery.
ꢀ
Maintain this equipment in a safe
ꢀ
Stop the engine and disconnect the spark
plug before allowing anybody’s hands in the
mixing drum.
operating condition at all times.
ꢀ
Caution must be exercised while servicing
this equipment. Rotating and moving parts
can cause injury if contacted.
ꢀ
Never pour or spray water over the engine
or electric motor.
ꢀ
Stop the engine before servicing, adding
ꢀ
Always stand clear of dump handle when
fuel and oil.
mixer is in operation. Any binding of material
between the mixer blades and drum will cause
drum and handle to quickly move in the
discharge position.
The safety instruction decals shown must be on all Essick Mixers
CAUTION!
PUTTING HANDS IN MIXING DRUM
SHUT OFF ENGINE BEFORE
Caution Decal is:
P/N EM948423
SAFETY INSTRUCTIONS
1. Do not operate or service this machine before reading the operating and maintenance manual.
2. Keep all inexperienced and/or unauthorized people away from equipment at all times.
3. Do not operate this equipment unless all guards and safety devices are attached and in place.
4. Keep this equipment in safe operating condition at all times.
5. Caution must be exercised while servicing this equipment.
Rotating and moving parts can cause injury if contacted.
6. Stop engine and allow to cool before adding fuel or oil.
7. Stop engine when leaving equipment.
8. Block unit when parking on a slope.
9. Unauthorized equipment modifications will void all warranties.
ESSICK CONSTRUCTION PRODUCTS A MULTIQUIP COMPANY CARSON, CALIFORNIA
The safety instruction decal is P/N EM948501
PAGE 6 — ESSICK EM-900S & 900P — PARTS & OPERATION MANUAL — REV. #7 (06/26/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY
There are no warranties, express or implied, made by Multiquip
Inc. hereunder on Products manufactured or distributed by it
except the warranty against defects in material and workmanship
on new Products to the original purchaser, as hereinafter set
forth.
There are no warranties, express or implied, in addition to the
above except as may be provided in writing by Multiquip Inc.
MULTIQUIP INC.SHALL NOT BE LIABLE FOR ANY SPECIAL,
INDIRECT OR CONSEQUENTIAL DAMAGES.
THE FOREGOINGWARRANTIES ARE IN PLACE AND IN LIEU
OF ALL WARRANTIES OF MERCHANTABILITY AND
FITNESS AND SETS FORTHTHE ENTIRE OBLIGATION OF
MULTIQUIP INC.
Multiquip Inc. warrants Products manufactured by it to be free
from defects in material and workmanship under normal and
proper use and servicing for the periods specified on the bottom
of this page.Warranty on the engines supplied with the Products
is limited to the warranty extended by the engine manufacturer.
Multiquip Inc.’sole obligation under this warranty is limited to the
replacement or repair, at its Carson, California facility, or such
authorized facility, of only such part or parts thereof as shall
appear to Multiquip Inc. upon inspection at such facility, to have
been defective in material and workmanship.
To avoid misrepresentations with respect to Products sold
hereunder, the Dealer agrees that no warranties, or other
operating guaranties on any Products covered by this Agreement
shall be made in excess of those made by Multiquip Inc.
Multiquip Inc. Warranty Periods:
A statement giving model and serial number of the Product, date
of sale to original purchaser and date and description of failure
shall accompany all parts.
EM-900.......................... 12 months
Any part or parts determined by Multiquip Inc.to be defective will
be replaced free of charge, F.O.B.Carson, California. Returned
parts subject to warranty must be shipped prepaid to Multiquip
Inc.within 30 days from the date the defective part or parts were
removed.This warranty does not apply to any part or parts which
have been subject to abuse or unauthorized repairs
Warranty with respect to Products, components and accessories
not manufactured by Multiquip Inc. is limited to the warranty
extended by the manufacturer of those items.
ESSICK EM-900S & 900P — PARTS & OPERATION MANUAL — REV. #7 (06/26/01) — PAGE 7
Download from Www.Somanuals.com. All Manuals Search And Download.
EM-900S & 900P — OPERATIONS
CONTROLS
KILL SWITCH: (Gasoline Engine Only) Located on the side of
the engine cover.
ENGINETHROTTLE AND CHOKE CONTROLS: Please refer
to the engine owners manual for specific instructions.The electric
motor switch ( electric motor only) located on the motor — is
used to start and stop the mixer.
DUMP LATCH: To dump the tub, grasp the dump handle and
lift the dump latch, then rotate the tub to discharge the mix.After,
discharge, return the tub to the vertical mixing position.
CLUTCH
GENERAL
The paddle shaft and mixing blades are engaged and
disengaged by tightening and loosening the drive belts with a
spring loaded idler pulley. To engage the clutch, rotate the
lever locates at the front of the mixer counterclockwise. The
spring maintains the correct belt tension. To disengage the
clutch, rotate the lever clockwise against the lever stop. The
engine base is slotted to adjust for belt wear and to bring the
idler pulley into operating range.
The Essick EM-700 and EM-900 Series plaster and mortar
mixers are quality mixers that have a batch capacity of 2.5 and
3.5 bags respectively.With proper care, they will give continuous
service year-after-year.
GASOLINE ENGINE CARE
For care and operation of the gasoline engine, refer to the
engine manufacturer’s operating instructions furnished with the
engine. We recommend draining and refilling the engine
crankcase at least every thirty hours of operation. Check the
engine oil level daily.
CAUTION: Stop the engine before allowing anybody to put
their hands in the mixing drum.
ELECTRIC MOTOR CARE
WHEEL BEARINGS
For lubrication care and operation of the electric motor, refer to
your electric motor instruction booklet furnished with the motor.
After every 3 months of operation, remove the hub dust cap
and inspect the wheel bearings.Once a year, or when required,
disassemble the wheel hubs remove the old grease and
repack the bearings forcing grease between rollers, cone and
cage with a good grade of high speed wheel bearing grease
(never use grease heavier than 265 A.S.T.M. penetration “No.
2.”) Fill the wheel hub with grease to the inside diameter of the
outer races and also fill the hub grease cap. Reassemble the
hub and mount the wheel. Then tighten the adjusting nut, at
the same time turn the wheel in both directions, until there is a
slight bind to be sure all the bearing surfaces are in contact.
Then back-off the adjusting nut 1/6 to 1/4 turn or to the nearest
locking hole or sufficiently to allow the wheel to rotate freely
within limits of .001" to .010" end play. Lock the nut at this
position. Install the cotter pin and dust cap, and tighten all
hardware.
Protect the electric motor from dust as much as possible and
keep ventilating openings clean. Do not spray water on the
electric motor.
Refer to the following chart. For recommend plug sizes.
115 VOLT 1Ø
EM 700
230 VOLT 1Ø
EM 900
MOTOR
PIGTAIL CAP CONN BODY PIGTAIL CAP CONN BODY
HORSE
POWER
NEMA/
NEMA/
NEMA/
NEMA/
ESSICK
ESSICK
ESSICK
ESSICK
1½ & 3 HP L5-30P/940545 L5-30R/940546 L6-15P/940550 L6-15R/940551
PAGE 8 — ESSICK EM-900S & 900P — PARTS & OPERATION MANUAL — REV. #7 (06/26/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
EM-900S & 900P — OPERATIONS
PADDLE SHAFT BEARING
IMPORTANT — DRUM HEAD SEAL CARE
The paddle shaft in the Essick Mixer rotates in sealed ball
bearings requiring no additional lubrication.
On each end of the mixing drum is a drum head containing self
adjusting paddle shaft seals. These seals consist of packing
rings, split glands and spring actuated adjusters. A properly
maintained seal prevents material from working around the
paddle shaft, causing excessive wear. The following is a
suggested procedure of maintenance for protection of the
paddle shaft and bearings:
BEARING BRACKET
Grease the bearing bracket every month.
A. Keep the drum head clean of plaster built up, so the spring
adjusters will be free to work.
COUNTERSHAFT
The countershaft rotates on two self-aligned pillow block
bearings. Grease these every 40 hours using grade #1 Lithium
Base grease.
B. Replace with one new ring of packing and waterproof grease
when split gland or pressure plate is about to bottom out against
the end of the drum.
New Packing
GEAR ALIGNMENT
When the old packing is to be completely replaced, coat shaft
and packing generously with a good grade of waterproof grease
and insert packing rings. Tighten the two spring adjuster nuts
on each end until the spring is compressed to 1¾ inches or the
top of the adjusting nut is even with the top of the drum head.
The countershaft and driven pinion are mounted on a slotted
base. To align gears, loosen pillow block mounting bolts and
move them until the necessary alignment has been made.
GEAR LUBRICATION
The surface of the pinion and the bull gear should be very
lightly greased every 250 hours.
Also, whenever the paddle shaft is removed, new waterproof
grease should be packed around the ball bearings in the drum
heads before reinstalling the shaft. Fill the cavity completely.
IMPORTANT! AVOID OVER-GREASING.
EXCESS GREASE WILL ACCUMULATE
DRUM GRILL
CONTAMINATES
PREMATUREWEAR.
AND
CAUSE
The drum opening is covered by a steel grill that is hinged for
easy cleaning. This grill should be closed at all times when
mixer is in use. Do not remove the grill or grill opening bar.
Keep the grill clean by washing it down daily.
CAUTION: Stop the engine before allowing anybody to put
their hands in the mixing drum.
ESSICK EM-900S & 900P — PARTS & OPERATION MANUAL — REV. #7 (06/26/01) — PAGE 9
Download from Www.Somanuals.com. All Manuals Search And Download.
EM-900S & 900P — OPERATIONS
TOWING — Before towing, check with local and state
laws for proper compliance.
STEP 1
The tow bar and chain must be properly attached to the mixer
and towing vehicle prior to towing. Refer to the following
installation instruction:
DRAW BAR
Step 1. Insert the Draw Bar into the main frame. Secure, utilizing
the ¾" bolt (grade 5) and nylock nut.Tighten to 100 foot pounds.
Step 2. Install the chain through the hole located between the
frame gusset and frame angle. Loop the chain together and
place under the Draw Bar. Secure with connector link.
BOLT & NUT
Step 3. Extend the chain along the length of the Draw Bar,
remove excess chain (slack) and secure to bottom connector
link. Secure the chain to the towing vehicle, using the
connector link.
INSERT CHAIN THROUGH
THE HOLE
STEP 2
NOTE: It is critical that the length of chain be properly adjusted
to prevent the Draw Bar and front mixer stand from
dropping to the ground (contact) in the event the Draw
Bar becomes disconnected from the towing vehicle.
DRAW BAR
FRAME ANGLE
DANGER
BEFORETOWING
FRAME GUSSET
CONNECTOR LINK
BALL HITCH COUPLER
STEP 3
VEHICLE
CONNECTOR LINK
1.
Check vehicle hitch, ball, and coupler for signs of wear or
damage. Replace any parts that are worn or damaged
before towing.
DRAW BAR
2.
Use only the 2" ball diameter as indicated on your coupler.
Use of any other ball diameter will create an extremely
dangerous condition which can result in separation of the
coupler and ball or ball failure.
REMOVE EXCESS
CHAIN (SLACK)
3.
4.
Be sure the coupler is secured to the hitch ball and the
lock lever is down tight and locked.
BOTTOM CONNECTOR LINK
Recheck tightness again after towing about 50 miles.
Check that trailer safety chains are properly connected.
SAFETY CHAIN .........................................P/N 3148
CONNECTOR LINK ...................................P/N 01004
RECOMMENDED MAINTENANCE
1.
Smear ball socket and clamp face with chassis grease.
Periodically oil pivot points and solutions surfaces of
coupler with SAE 30 wt. motor oil.
2.
When parking or storing your trailer. Keep the coupler off
the ground so dirt will not build up in the ball socket.
DANGER
If housing is deformed,
replace complete coupler.
USE ONLY GENUINE
FULTON REPAIR KITS.
PAGE 10 — ESSICK EM-900S & 900P — PARTS & OPERATION MANUAL — REV. #7 (06/26/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
EM-900S & 900P — OPERATIONS
CLEANING — BLADE ADJUSTMENTS
Always disconnect the spark plug wire before cleaning the inside
of the drum.
Never pour or spray water over the gasoline engine or electric
motor.
For consistent performance, long life and high quality mixing,
thoroughly clean the mixer inside and out at the end of each
day’s operation.To prevent lumps of dried mortar from forming
and contamination of future batches, do not allow a buildup of
materials to form on the blades or anywhere inside the drum.
The following is the recommended wiper blade adjustments:
1) STEEL DRUM MIXERS
2) POLYETHYLENE DRUM MIXERS
The poly blade should come as close as possible to the surface
without touching. If material builds up on the drum, you may
use a rubber mallet to dislodge the material without adverse
effect to the drum.
IMPORTANT NOTICE
EPOXY COMPATIBILITY — There are some expoxies and
other chemicals used in certain applications that are not
compatible with polyethylene tubs.
Since Whiteman Industries cannot control the end user’s
application of this product, we will not assume responsibility
for the resulting damages when exposed to incompatible
chemicals.
ESSICK EM-900S & 900P — PARTS & OPERATION MANUAL — REV. #7 (06/26/01) — PAGE 11
Download from Www.Somanuals.com. All Manuals Search And Download.
EM-900S & 900P — SPECIFICATIONS
EM-900S SPECIFICATIONS
MODEL
U.S.(inch)
METRIC
CAPACITY ....................................................9 CUBIC FEET ....................................................... 248 LITERS
BAG CAPACITY .............................................2½ - 3½ ............................................................ 2½ - 3½
WEIGHT (APPROX.).......................................780 LBS. ............................................................. 395 KG.
L
X
W
X
H ..................................................71
X
50
X
59 IN. .................................................. 180
X
127
X
150 CM.
LENGTH W/TOW BAR ......................................98 IN. ................................................................. 248 CM.
HEIGHT W/DUMP HANDLE ................................77 IN. ................................................................. 195 CM.
DISCHARGE HEIGHT .......................................21 IN. ................................................................. 53 CM.
DRIVE .........................................................V-BELT TO GEAR ..................................................... —
DUMP ACTION ..............................................MANUAL ............................................................... —
EM-900P SPECIFICATIONS
MODEL
U.S.(inch)
METRIC
CAPACITY ....................................................9 CUBIC FEET ....................................................... 248 LITERS
BAG CAPACITY .............................................2½ - 3½ ............................................................ 2½ - 3½
WEIGHT (APPROX.).......................................796 LBS. ............................................................. 395 KG.
L
X
W
X
H ..................................................71
X
50
X
59IN. ................................................... 180
X
127
X
150 CM.
LENGTH W/TOW BAR ......................................98 IN. ................................................................. 248 CM.
HEIGHT W/DUMP HANDLE ................................77 IN. ................................................................. 195 CM.
DISCHARGE HEIGHT .......................................21 IN. ................................................................. 53 CM.
DRIVE .........................................................V-BELT TO GEAR ..................................................... —
DUMP ACTION ..............................................MANUAL ............................................................... —
NOTE: In accordance with our established policy of constant improvement, we reserve the right to amend these specifications at anytime without notice.
PAGE 12 — ESSICK EM-900S & 900P — PARTS & OPERATION MANUAL — REV. #7 (06/26/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE PAGE
ESSICK EM-900S & 900P — PARTS & OPERATION MANUAL — REV. #7 (06/26/01) — PAGE 13
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLANATION OF CODE IN REMARKS COLUMN
How to read the marks and remarks used in this parts book.
Section 1: Items Found In the “Remarks” Column
Serial Numbers-Where indicated, this indicates a serial
number range (inclusive) where a particular part is used.
Model Number-Where indicated, this shows that the
corresponding part is utilized only with this specific model
number or model number variant.
Section 2: Items Found In the “Remarks” Column
Serial Numbers-Where indicated, this indicates a serial number
range (inclusive) where a particular part is used.
Model Number-Where indicated, this shows that the
corresponding part is utilized only with this specific model number
or model number variant.
Section 3: Items Found In the “Items Number” Column
All parts with same symbol in the number column, , #,
, belong to the same assembly or kit.
+
, %, or
*
ꢀ
Note: If more than one of the same reference number is listed,
the last one listed indicates newest (or latest) part available.
NOTE
If more than one of the same reference number is
listed, the last one listed indicates newest (or latest)
part available.
NOTE
The contents of this catalog are
subject to change without notice.
PAGE 14 — ESSICK EM-900S & 900P — PARTS & OPERATION MANUAL — REV. #7 (06/26/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
EM-900S & 900P — SUGGESTED SPARE PARTS
EM-900 S/P
EM-900 S/P
1 to 3 Units
5+ Units
Qty.
P/N
Description
Qty.
P/N
Description
3 ......... EM505834 ........... V-BELT
5 ......... EM505834 ........... V-BELT
3 ......... 491115 ................ V-BELT, w/ELECTRIC MOTOR
6 ......... 491010 ................ LATCH w/ASSY
3 ......... EM200863 ........... BLADE KIT STEEL DRUM
3 ......... EM204625 ........... BLADE KIT POLY DRUM
12 ....... EM200301 ........... PACKING RING
4 ......... EM200794 ........... SPRING
5 ......... 491115 ................ V-BELT, w/ELECTRIC MOTOR
10 ....... 491010 ................ LATCH w/ASSY
5 ......... EM200863 ........... BLADE KIT STEEL DRUM
5 ......... EM204625 ........... BLADE KIT POLY DRUM
24 ....... EM200301 ........... PACKING RING
8 ......... EM200794 ........... SPRING
8 ......... EM200286 ........... SPECIAL BOLT
4 ......... EM200286 ........... SPECIAL BOLT
1 ......... 3351 .................... PINION GEAR
2 ......... EM902153 ........... BEARING
1 ......... EM940734 ........... SWITCH, ON/OFF
1 ......... 509171 ................ DUMP HANDLE: POLY DRUM
2 ......... 3351 .................... DRIVEN PINON GEAR
1 ......... EM201537 ........... DUMP HANDLE, STEEL DRUM
2 ......... 3065 .................... SEAL, AXLE
2 ......... 3469 .................... DUST CAP AXLE
2 ......... EM903049 ........... BEARING CONE UP TO S/N 9896000
2 ......... EM903113 ........... BEARING CONE STARTING S/N 2080000
2 ......... EM903012 ........... BEARING CUP
NOTE
Part numbers on this Suggested
Spare Parts List may supercede/
replace the P/N shown in the text
pages of this book.
ESSICK EM-900S & 900P — PARTS & OPERATION MANUAL — REV. #7 (06/26/01) — PAGE 15
Download from Www.Somanuals.com. All Manuals Search And Download.
EM-900S & 900P — DRUM HEAD ASSEMBLY
PAGE 16 — ESSICK EM-900S & 900P — PARTS & OPERATION MANUAL — REV. #7 (06/26/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
EM-900S & 900P — DRUM HEAD ASSEMBLY
DRUM HEAD ASSEMBLY
DRUM HEAD
NO.
4
PART NO.
PART NAME
COLLAR
QTY.
1
REMARKS
EM200018
EM902153
EM507720
500076
5
BEARING
2
6
6
7
8
9
10
11
12
13
13
14
15
16
DUMP BEARING ..................................................................... 2 ................. STARTING S/N 98624090
DUMP BEARING ..................................................................... 2 ................. FROM S/N 9862400 TO 9862489
GREASE ZERK ........................................................................ 2 ................. REPLACES 491705
ADJUSTING PLATE
SPECIAL BOLT
PACKING GLAND HALF
FOLLOWER
PACKING RING
DRUM HEAD ........................................................................... 2 ................. STARTING S/N 98624090
DRUM HEAD ........................................................................... 2 ................. FROM S/N 9862400 TO 9862489
SPRING
ADJUSTING NUT
BOLT
EM916019
EM200288
EM200286
EM200285
EM200303
EM200301
EM201648
EM507272
EM200794
EM200287
EM966048
2
4
4
2
12
4
4
8
ESSICK EM-900S & 900P — PARTS & OPERATION MANUAL — REV. #7 (06/26/01) — PAGE 17
Download from Www.Somanuals.com. All Manuals Search And Download.
Y
46
47
48
49
61
58 59 60
TOW END
PAGE 18 — ESSICK EM-900S & 900P — PARTS & OPERATION MANUAL — REV. #7 (06/26/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
EM-900S, 900P — PADDLE SHAFT ASSEMBLY
PADDLE SHAFT ASSEMBLY
NO.
46
47
48
49
50
51
52
53
54
PART NO.
PART NAME
U-BOLT
NUT HEX ½-13
U-BOLT INSERT
QTY.
REMARKS
EM200297
EM968011
EM200292
EM507274
EM200293
EM200294
EM200296
EM200295
EM203432
EM203433
EM200212
EM507519
EM200213
EM507518
EM963837
6109180
2
4
4
PADDLE SHAFT
PADDLE ARM-TOW END
PADDLE ARM-CENTER
PADDLE ARM-ENGINE END
PADDLE ARM-CENTER
CENTER BACK-UP BLADE
END BACK-UP BLADE
TOP RUBBER BLADE (STEEL) DRUM ONLY
TOP PLASTIC BLADE (POLY) DRUM ONLY
END RUBBER BLADE (STEEL) DRUM ONLY
END PLASTIC BLADE (POLY) DRUM ONLY
BOLT ½"-13 X 5-½"
1
1
1
1
4
2
4
4
2
2
1
1
1
1
#
#
*
55
56
56#
57
57#
58
*
*
*
59
60
61
LOCK WASHER ½"
HEX NUT ½"-13
SPACER, BULL GEAR
REPLACES EM923638
EM968011
EM507251
EM200863
EM204625
EM203028
BLADE KIT, (STEEL) DRUM ONLY .......................................... 1 ............... INCLS ITEMS w/ AND MTG. HDWR
BLADE KIT, (POLY) DRUM ONLY ............................................. 1 ............... INCLS ITEMS w/# AND MTG. HDWR
HARDWARE KIT, (RUBBER/POLY BLADES) ........................... 1 ............... INCLUDED IN BLADE KITS
*
REFER TO PAGES 14 & 15 FOR DRUM HEAD BREAKDOWN
ESSICK EM-900S & 900P — PARTS & OPERATION MANUAL — REV. #7 (06/26/01) — PAGE 19
Download from Www.Somanuals.com. All Manuals Search And Download.
EM-900S — STEEL DRUM
STEEL DRUM
109
108
110 111
PAGE 20 — ESSICK EM-900S & 900P — PARTS & OPERATION MANUAL — REV. #7 (06/26/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
EM-900S — STEEL DRUM
STEEL DRUM
NO.
PART NO.
PART NAME
QTY.
REMARKS
100#
101
101
101
102
103
104#
105#
106%
EM201537
EPC-1
EBC-1
HBC-1
EM963580
EM969038
EM203332
EM507484
EM507765
EM507766
DUMP HANDLE
1
TOWING TONGUE (P. EYE) .................................... 1 .............. NO LONGER AVAILABLE
TOWING TONGUE (PIN HOLE) .............................. 1 .............. CONTACT MQ SALES DEPT./ACCESSORY ITEM
TOWING TONGUE (BALL HITCH) .......................... 1 .............. CONTACT MQ SALES DEPT./ACCESSORY ITEM
CAP SCREW ........................................................... 1 .............. REPLACES 505067
LOCK NUT ............................................................... 1 .............. REPLACES 505069
DRUM GRILL
1
1
GRILL OPEN BAR
DRUM ASSY (STEEL) ............................................. 1 .............. INCLS. ITEMS w/#
DRUM & SHAFT ASSY (COMPLETE) (STEEL) ..... 1 .............. INCLS. ITEMS w/% AND DRUM HEAD &
PADDLE SHAFT ASSY
108
109
110
111
❑
EM506309
507264
EM507421
EM507835
3148
MAIN FRAME
CLUTCH LEVER
DUMP LATCH
CLEVIS PIN
SAFETY CHAIN
5/16" CONNECTOR LINK
1
1
1
1
1
2
REPLACES 13363
❑
❑
01004
ILLUSTRATED ON PAGE 10
ESSICK EM-900S & 900P — PARTS & OPERATION MANUAL — REV. #7 (06/26/01) — PAGE 21
Download from Www.Somanuals.com. All Manuals Search And Download.
EM-900P — POLYETHYLENE DRUM
POLYETHYLENE
DRUM
122
123
124
125
126
127
124
125
128
129
PAGE 22 — ESSICK EM-900S & 900P — PARTS & OPERATION MANUAL — REV. #7 (06/26/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
EM-900P — POLYETHYLENE DRUM
POLYETHYLENE DRUM
NO.
115#
116
117#
118#
119#
120#
121
PART NO.
EM506310
EM506897
507416
PART NAME
QTY.
1
1
1
1
1
1
1
REMARKS
PLASTIC DRUM W/O GRATES
SUPPORT REAR
STATIONARY GRATE
MOVEABLE GRATE
GRATE OPEN BAR
DUMP HANDLE
507417
507517
509171
EM506896
EM509604
DRUM SUPPORT
DRUM & SHAFT ASSY (COMPLETE) (POLY) ........................ 1 ...................... INCLS ITEMS W/# AND HEAD
END & PADDLE SHAFT ASSY
122
123
124
125
126
127
128
129
EM963610
EM969013
5041987
EM969079
505196
505066
492392
HHCS 3/8" NC X 1/4" G-5 ....................................................... 7 ...................... REPLACES 492376
LOCK NUT 3/8" NC ................................................................. 7 ...................... REPLACES 492583
FHCS 1/4" NC X 1" G-5 ........................................................... 8 ...................... REPLACES 504987
LOCK NUT 1/4" NC ................................................................. 8 ...................... REPLACES 492581
3/8 X 1½" HHCS
3/8" LOCKNUT
8
8
3
3
½" X 1 NC G-5 BOLT
½" LOCK NUT
492584
ESSICK EM-900S & 900P — PARTS & OPERATION MANUAL — REV. #7 (06/26/01) — PAGE 23
Download from Www.Somanuals.com. All Manuals Search And Download.
EM-900S & 900P — GAS ENGINES, PULLEYS & CAB ASSEMBLY
PAGE 24 — ESSICK EM-900S & 900P — PARTS & OPERATION MANUAL — REV. #7 (06/26/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
EM-900S & 900P — GAS ENGINES, PULLEYS & CAB ASSEMBLY
GAS ENGINES, PULLEYS & CAB ASSEMBLY
COMMON PARTS
NO.
150
151
152
153
154
155
156
157
158
159
167
168
169
170
171
PART NO.
EM507159
491010
PART NAME
CAB ASSEMBLY
QTY.
1
REMARKS
LATCH ASSEMBLY ................................................. 2 .................. REPLACES 504744
DRIVE GEAR 16-½ DIA.
ROD END
EM505671
EM959080
EM102014
EM901515
EM905016
EM203098
3351
EM940734
502226
JISB2804C25
500214
1
2
1
1
2
1
SPRING
IDLER PULLEY
PILLOW BLOCK BEARING
SPRING CLIP
DRIVEN PINION GEAR .......................................... 1 .................. REPLACES 500272
SWITCH, ON/OFF
COUNTER SHAFT
SNAP RINGS .......................................................... 2 .................. REPLACES 490957
KEY
1
1
1
1
1
EM010023
EM963064
KEY
BOLT 3/8 X16 X 3-1/4
MODEL EM 900 w/HONDA
NO.
161
161
162
163
163
164
165
166
PART NO.
PART NAME
QTY.
REMARKS
GX240K1HA2
GX160K1HX2
492057
EM901074
492055
EM505834
EM507490
EM507491
HONDA ENGINE GX240 K1HA 8HP ...................... 1 .................. REPLACES 493261
HONDA ENGINE GX160 5.5HP ENG.
DRIVEN PULLEY-LARGE
DRIVE PULLEY-SMALL 1" BORE-8HP HONDA
DRIVE PULLEY-5.5 HP HONDA
V-BELT
THREADED ROD
IDLER ARM
1
1
1
1
2
1
1
MODEL EM900 w/WISCONSIN
NO.
161
162
163
164
165
166
PART NO.
EM937171
EM505204
505205
PART NAME
QTY.
REMARKS
WISCONSIN ENGINE BKN2-408472 ..................... 1 .................. REPLACES 505208
DRIVEN PULLEY
DRIVE PULLEY
V-BELT
THREADED ROD
IDLER ARM
1
1
2
1
1
507775
EM507771
EM203352
MODEL EM 900 w/ROBIN
NO.
161
161
162
163
164
165
166
PART NO.
PART NAME
QTY.
REMARKS
W1280800466
EH252YR0000
492057
ROBIN ENGINE 8HP EY-28 .................................... 1 .................. UP TO OCTOBER, 1999
ROBIN ENGINE 8HP EH25-2 ................................. 1 .................. STARTING OCTOBER, 1999, REPLACES 493260
DRIVEN PULLEY-LARGE
DRIVE PULLEY-SMALL
V-BELT
1
1
2
1
1
492054
EM505834
EM507490
EM203352
THREADED ROD
IDLER ARM
MODEL EM-900 w/B&S
NO.
161
161
162
163
164
165
166
PART NO.
PART NAME
QTY.
REMARKS
1964521049
1352321036E1
492057
EM901074
EM505834
EM507490
EM507491
B&S ENGINE 8HP .................................................. 1 .................. REPLACES 493181
B&S ENGINE 5HP
DRIVEN PULLEY-LARGE
DRIVE PULLEY-SMALL 1" BORE
V-BELT
1
1
1
2
1
1
THREADED ROD
IDLER ARM
ESSICK EM-900S & 900P — PARTS & OPERATION MANUAL — REV. #7 (06/26/01) — PAGE 25
Download from Www.Somanuals.com. All Manuals Search And Download.
EM-900S & 900P — ELECTRIC MOTOR & PULLEYS
PAGE 26 — ESSICK EM-900S & 900P — PARTS & OPERATION MANUAL — REV. #7 (06/26/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
EM-900S & 900P — ELECTRIC MOTOR & PULLEYS
ELECTRIC MOTOR & PULLEYS
NO.
PART NO.
PART NAME
QTY.
1
REMARKS
161
162
163
164
165
166
EM939315
EM505204
EM901513
491115
EM507490
EM507713
507715
ELECTRIC MOTOR 3.0 H.P
DRIVEN PULLEY
DRIVE PULLEY
V-BELT
THREADED ROD
IDLER ARM
1
1
2
1
1
GUIDE, V-BELT .................................................................................. 1 ................. NOT ILLUSTRATED
FOR COMMON PARTS SEE PAGE 25
ESSICK EM-900S & 900P — PARTS & OPERATION MANUAL — REV. #7 (06/26/01) — PAGE 27
Download from Www.Somanuals.com. All Manuals Search And Download.
EM-900S & 900P — AXLE & WHEEL GROUP
PAGE 28 — ESSICK EM-900S & 900P — PARTS & OPERATION MANUAL — REV. #7 (06/26/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
EM-900S & 900P — AXLE & WHEEL GROUP
WHEEL GROUP EM-700 & 900
NO.
200
200
201 #
202
203
204
204
205
PART NO.
EM507407
511334
3065
504708
507444
3068
8164
0183
3005
PART NAME
QTY.
REMARKS
AXLE, RIGID ....................................... 1 .................... UP TO S/N 98960000
AXLE, RIGID ....................................... 1 .................... STARTING S/N 20800000
SEAL
THICK SPACER .................................. 2 .................... 3/4" INSIDE DIAMETER
THIN SPACER .................................... 2 .................... 3/4" INSIDE DIAMETER
AXLE NUT ........................................... 2 .................... UP TO S/N 98960000
AXLE NUT ........................................... 2 .................... STARTING S/N 20800000
2
*
COTTER PIN
RIM & TIRE ONLY
2
2
206
208
EM942000
3469
8115
VALVE STEM ....................................... 1 .................... REPLACES 942052
209 #
DUST CAP
LUG NUT
2
8
*
210 #
211
*
EM903049
EM903113
EM903012
3504
BEARING CONE ................................. 2 .................... UP TO S/N 98960000
BEARIING CONE ................................ 2 .................... STARTING S/N 20800000
*
211#
212 #
BEARING CUP
2
*
213
HUB W/ BEARING CUP ...................... 2 .................... UP TO S/N 9896000, INCLUDES ITEM w/
HUB W/ BEARING CUP ...................... 2 .................... STARTING S/N 20800000, INCLUDES ITEM w/#
*
213
EM941306
ESSICK EM-900S & 900P — PARTS & OPERATION MANUAL — REV. #7 (06/26/01) — PAGE 29
Download from Www.Somanuals.com. All Manuals Search And Download.
Effective: July 1, 2000
TERMS AND CONDITIONS OF SALE — PARTS
PAYMENT TERMS
4. Freight is at the sender’s expense. All
partsmustbereturnedfreightprepaidto
Multiquip’sdesignatedreceivingpoint.
PRICINGANDREBATES
Terms of payment for parts are net 10 days.
Prices are subject to change without prior
notice.Pricechangesareeffectiveonaspecific
dateandallordersreceivedonorafterthatdate
willbebilledattherevisedprice. Rebatesfor
price declines and added charges for price
increases will not be made for stock on hand
at the time of any price change.
5. Parts must be in new and resalable
condition,intheoriginalMultiquippackage
(ifany),andwithMuiltiquippartnumbers
clearly marked.
FREIGHT POLICY
All parts orders will be shipped collect or
prepaidwiththechargesaddedtotheinvoice.
All shipments are F.O.B. point of origin.
Multiquip’s responsibility ceases when a
signed manifest has been obtained from the
carrier,andanyclaimforshortageordamage
mustbesettledbetweentheconsigneeandthe
carrier.
6. Thefollowingitemsarenotreturnable:
Multiquip reserves the right to quote and sell
directtoGovernmentagencies,andtoOriginal
Equipment Manufacturer accounts who use
our products as integral parts of their own
products.
a. Obsolete parts.(If an item is listed
in the parts price book as being
replaced by another item, it is
obsolete.)
b. Any parts with a limited shelf life
(such as gaskets, seals, “O” rings,
andotherrubberparts)thatwere
purchasedmorethansixmonths
priortothereturndate.
MINIMUMORDER
SPECIAL EXPEDITING SERVICE
TheminimumchargeforordersfromMultiquip
is $15.00 net. Customers will be asked for
instructionsregardinghandlingofordersnot
meetingthisrequirement.
A$20.00to$50.00surchargewillbeaddedto
theinvoiceforspecialhandlingincludingbus
shipments, insured parcel post or in cases
where Multiquip must personally deliver the
parts to the carrier.
c. Anylineitemwithanextendeddealer
netpriceoflessthan$5.00.
d. Special order items.
RETURNED GOODS POLICY
e. Electricalcomponents.
LIMITATIONS OF SELLER’S LIABILITY
Returnshipmentswillbeacceptedandcredit
will be allowed, subject to the following
provisions:
f.
Paint, chemicals, andlubricants.
Multiquip shall not be liable here under for
damagesinexcessofthepurchasepriceofthe
item with respect to which damages are
claimed, and in no event shall Multiquip be
liable for loss of profit or good will or for any
other special, consequential or incidental
damages.
g. Decalsandpaperproducts.
h. Items purchased in kits.
1. AReturnedMaterialAuthorizationmust
beapprovedbyMultiquippriortoshipment.
7. Thesenderwillbenotifiedofanymaterial
receivedthatisnotacceptable.
2. ToobtainaReturnMaterialAuthorization,
alistmustbeprovidedtoMultiquipParts
Sales that defines item numbers,
quantities,anddescriptionsoftheitems
tobereturned.
8. Such material will be held for 5 working
days from notification, pending
instructions. If a reply is not received
within5days,thematerialwillbereturned
tothesenderathisexpense.
LIMITATIONOFWARRANTIES
a. Thepartsnumbersanddescriptions
must match the current parts price
list.
Nowarranties,expressorimplied,aremade
in connection with the sale of parts or trade
accessories nor as to any engine not
manufacturedbyMultiquip.Suchwarranties
made in connection with the sale of new,
complete units are made exclusively by a
statement of warranty packaged with such
units, and Multiquip neither assumes not
authorizes any person to assume for it any
other obligation or liability whatever in
connectionwiththesaleofitsproducts.Apart
fromsuchwrittenstatementofwarranty,there
arenowarranties,express,impliedorstatutory,
which extend beyond the description of the
productsonthefacehereof.
9. Creditonreturnedpartswillbeissuedat
dealer net price at time of the original
purchase,lessa15%restockingcharge.
b. The list must be typed or computer
generated.
10. In cases where an item is accepted for
which the original purchase document
can not be determined, the price will be
basedonthelistpricethatwaseffective
twelve months prior to the RMA date.
c. Thelistmuststatethereason(s)for
thereturn.
d. The list must reference the sales
order(s) or invoice(s) under which
theitemswereoriginallypurchased.
11. Credit issued will be applied to future
purchasesonly.
e. Thelistmustincludethenameand
phonenumberoftheperson
requestingtheRMA.
3. A copy of the Return Material
Authorizationmustaccompanythereturn
shipment.
PAGE 30 — ESSICK EM-900S & 900P — PARTS & OPERATION MANUAL — REV. #7 (06/26/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE PAGE
ESSICK EM-900S & 900P — PARTS & OPERATION MANUAL — REV. #7 (06/26/01) — PAGE 31
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS AND OPERATION MANUAL
HERE'S HOW TO GET HELP
PLEASE HAVE THE MODEL AND SERIAL NUMBER
ON-HAND WHEN CALLING
PARTS DEPARTMENT
800-427-1244 or 310-537-3700
FAX: 800-672-7877 or 310-637-3284
^6668
SERVICE DEPARTMENT/TECHNICAL ASSISTANCE
800-478-1244 or 310-537-3700
FAX: 310- 537-4259
WARRANTY DEPARTMENT
888-661-4279, or 310-661-4279
FAX: 310- 537-1173
MAIN
800-421-1244 or 310-537-3700
FAX: 310-537-3927
MULTIQUIP INC.
POST OFFICE BOX 6254
CARSON, CA 90749
310-537-3700 • 800-421-1244
FAX:310-537-3927
WWW:multiquip.com
Atlanta • Boise • Dallas • Houston • Newark
Quebec, Canada • Manchester, UK • Rio De Janiero, BR • Guadalajara, MX
Download from Www.Somanuals.com. All Manuals Search And Download.
|