OPERATION AND PARTS MANUAL
WC-62S
WC-62P
WHITEMAN SERIES
CONCRETE MIXERS
FINAL REVISION
Revision #7 (06/30/05)
MULTIQUIPINC.
18910 WILMINGTON AVE.
PARTS DEPARTMENT:
800-427-1244
CARSON, CALIFORNIA 90746 FAX: 800-672-7877
310-537-3700
800-421-1244
SERVICE DEPARTMENT/TECHNICAL ASSISTANCE:
800-478-1244
FAX:310-537-3927
FAX:310-631-5032
Atlanta • Boise • Dallas • Houston • Newark
Montreal, Canada • Manchester, UK
Rio De Janiero, Brazil • Guadalajara, Mexico
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
HERE'S HOW TO GET HELP
PLEASE HAVE THE MODEL AND SERIAL
NUMBER ON-HAND WHEN CALLING
MULTIQUIP’SMAINPHONENUMBERS
800-421-1244
310-537-3700
FAX: 310-537-3927
PARTSDEPARTMENT
800-427-1244
310-537-3700
FAX: 800-672-7877
FAX: 310-637-3284
MAYCOPARTS
800-306-2926
310-537-3700
FAX: 800-672-7877
FAX: 310-637-3284
SERVICEDEPARTMENT
800-478-1244
310-537-3700
FAX: 310-537-4259
MQPOWERSERVICEDEPARTMENT
800-835-2551
310-537-3700
FAX: 310-638-8046
TECHNICALASSISTANCE
800-478-1244
FAX: 310-631-5032
WARRANTYDEPARTMENT
800-421-1244, EXT. 279 FAX: 310-537-1173
310-537-3700, EXT. 279
WC-62P/S CONCRETE MIXER — PARTS & OPERATION MANUAL — REV. #7 (06/30/05) — PAGE 3
Download from Www.Somanuals.com. All Manuals Search And Download.
WC-62P/S CONCRETE MIXER — TABLE OF CONTENTS
MQ WHITEMAN WC-62P/S
Concrete Mixers
HONDA GX240K1HA2 ENGINE
Air Cleaner Assembly......................................... 50-51
Camshaft Assembly ........................................... 52-53
Carburetor Assembly ......................................... 54-55
Control Assembly ............................................... 56-57
Crankcase Cover Assembly............................... 58-59
Crankshaft Assembly ......................................... 60-61
Cylinder Barrel Assembly................................... 62-63
Cylinder Head Assembly.................................... 64-65
Fan Cover Assembly .......................................... 66-67
Flywheel Assembly ............................................ 68-69
Muffler Assembly ............................................... 70-71
Fuel Tank Assembly ........................................... 72-73
Ignition Coil ........................................................ 74-75
Piston Assembly................................................. 76-77
Recoil Starter ..................................................... 78-79
Gear Reduction Assembly ................................. 80-81
Label Assembly.................................................. 82-83
Here's How To Get Help ............................................ 3
Table Of Contents ..................................................... 4
Parts Ordering Procedures ....................................... 5
Specifications ............................................................ 6
Dimensions (Mixer) ................................................... 7
Safety Message Alert Symbols ................................. 8
Rules For Safe Operation .................................... 9-10
Operation and Safety Decals .................................. 11
General Information ................................................ 12
Mixer Basic Components ........................................ 13
Basic Engine Components...................................... 14
Handwheel Assembly.............................................. 15
Towing Guidelines ................................................... 16
Safety Chain Connection ........................................ 17
Electric Motor ..................................................... 18-19
Pre-Inspection (Gasoline Engine) ........................... 20
Initial Start-up (Gasoline Engine)............................ 21
Initial Start-up (Electric Motor) ................................ 22
Operation ................................................................ 23
Maintenance (Engine)........................................ 24-25
Maintenance (Mixer) .......................................... 26-28
Troubleshooting (Engine)........................................ 30
Troubleshooting (Engine/Mixer) .............................. 31
Explanation Of Code In Remarks Column .............. 32
Suggested Spare Parts ........................................... 33
HONDA GX160K1H X2 ENGINE
Air Cleaner Assy.................................................84-85
Camshaft Assy. ..................................................86-87
Carburetor Assy. ................................................88-89
Control Assy. ......................................................90-91
Crankcase Cover Assy. ......................................92-93
Crankshaft Assy. ................................................94-95
Cylinder Barrel Assy. ..........................................96-97
Cylinder Head Assy. ...........................................98-99
Fan Cover Assy. .............................................100-101
Flywheel Assy.................................................102-103
Fuel Tank Asssembly .....................................104-105
Ignition Coil Asssembly ..................................106-107
Muffler Asssembly..........................................108-109
Piston Rings Asssembly .................................110-111
Recoil Starter Asssembly...............................112-113
1/6 Gear Reduction Asssembly .....................114-115
Labels Asssembly ..........................................116-117
ComponetDrawings
Nameplate and Decals....................................... 34-35
Mixer Assembly (Steel Drum) ............................ 36-37
Mixer Assembly (Plastic Drum) .......................... 38-39
Main Frame Assembly ....................................... 40-41
Axle Assembly .................................................... 42-43
Cabinet Assembly .............................................. 44-45
Gas Engine Mounting Plate Asasembly............ 46-47
Electric Motor Mounting Plate Asasembly ........ 48-49
Terms and Conditions of Sale ............................... 118
Specification and part number
are subject to change without
notice.
PAGE 4 —WC-62P/S CONCRETE MIXERS — PARTS & OPERATION MANUAL — REV. #7 (06/30/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
WC-62P/S CONCRETE MIXER — PARTS ORDERING PROCEDURES
When ordering parts,
please supply the following information:
❒
Dealeraccountnumber
❒
❒
❒
❒
❒
❒
Dealernameandaddress
Shipping address (if different than billing address)
Returnfaxnumber
Applicable model number
Quantity,part number and description of each part
Specifypreferredmethodofshipment:
Note:Unlessotherwiseindicatedbycustomer, all
orders are treated as “Standard Orders”, and will
ship within 24 hours.We will make every effort to
ship “Air Shipments” the same day that the order is
received, if prior to 2PM west coast time. “Stock
Orders” must be so noted on fax or web forms.
✓
✓
✓
✓
✓
✓
FedEx or UPS Ground
FedEx or UPS Second Day or Third Day
FedEx or UPS Next Day
Federal Express Priority One
DHL
Truck
Place Your Parts Order Via Web or Fax
For Even More Savings!
Here’s how to get help...
Please have the model and serial number on
hand when calling.
Parts Department
800-427-1244
310-537-3700
Fax:800-672-7877
Fax:310-637-3284
Extra Discounts!
All parts orders which include complete part numbers
and are received by our automated web parts order
system, or by fax qualify for the following extra
discounts:
Mayco Parts
800-306-2926
310-537-3700
Fax:800-672-7877
Fax:310-637-3284
Ordered
via
Standard
orders
Stock orders
($750 list and above)
Service Department
800-478-1244
310-537-3700
Fax:310-537-4259
Fax
3%
5%
10%
10%
Web
MQ Power Service Department
800-835-2551
310-537-3700
Fax:310-638-8046
Special freight allowances
when you order 10 or more
line items via Web or Fax!**
FedEx Ground Service at no charge for freight
Technical Assistance
800-478-1244
Fax:310-631-5032
Fax:310-537-1173
Warranty Department
800-421-1244, Ext. 279
310-537-3700, Ext. 279
No other allowances on freight shipped by any other
carrier.
Multiquip’s Main Phone Numbers
NOTE:DISCOUNTSARESUBJECTTOCHANGE
800-421-1244
310-537-3700
Fax:310-537-3927
Direct TOLL-FREE access
to our Parts Department:
Toll-free nationwide — 800-427-1244
MULTIQUIP INC.
18910 WILMINGTON AVENUE
POST OFFICE BOX 6254
CARSON, CALIFORNIA 90749
310-537-3700•800-421-1244
FAX:310-537-3927
WWW:multiquip.com
WC-62P/S CONCRETE MIXER — PARTS & OPERATION MANUAL — REV. #7 (06/30/05) — PAGE 5
Download from Www.Somanuals.com. All Manuals Search And Download.
WC-62P/S CONCRETE MIXER — SPECIFICATIONS
Table 1. Specifications (Engines/Electric Motor)
Model
HONDA GX160K1HX2
HONDA GX240K1HA2
ROBIN EH-252YR000
Baldor 35LYL229
Air-cooled 4 stroke, Single
Cylinder, OHV, Horizontal Shaft
Gasoline Engine
Air-cooled 4 stroke, Single Cylinder,
OHV, Horizontal Shaft Gasoline Engine
Air-cooled 4 stroke, Single Cylinder,
OHV, Horizontal Shaft Gasoline Engine
1.5 HP, Single-phase 115/230
VAC, Electric Motor
Type
2.7 in. X 1.8 in.
(68 mm x 45 mm)
2.90 in. X 2.30 in.
(73 mm x 58 mm)
2.95 in. X 2.24 in.
(75 mm x 57 mm)
Bore X Stroke
N/A
Displacement
Max Output
9.9 cu. in. (163 cc)
5.5 H.P./4000 rpm
14.81 cc
15.31 cc
N/A
8.0 H.P./3600 R.P.M.
8.5 H.P./4000 R.P.M.
1.5 HP/1725 R.P.M.
Engine/Electric
Motor
Approx. 1.59 U.S. Gallons
(6 Liters)
Approx. 1.59 U.S. Gallons
(6 Liters)
Fuel Tank Capacity
0.95 U.S. Gallons (3.6 Liters)
N/A
Fuel
Unleaded Automobile Gasoline
0.63 qt. (0.6 liter)
Unleaded Gasoline
2-1/3 pints
Unleaded Gasoline
2 pints
N/A
N/A
Lube Oil Capacity
Speed Control
Method
Centrifugal Fly-weight Type
Centrifugal Fly-weight Type
Centrifugal Fly-weight Type
N/A
Starting Method
Input Voltage
Recoil Start
N/A
Recoil Start
N/A
Recoil Start
N/A
Electric
115/230 VAC Single Phase
Dimension
(L x W x H)
12.3 x 14.3 X 13.2 in.
(312 X 362 X 335 mm)
14.0 x 16.9 X 16.1 in.
(355 X 430 X 410 mm)
14.40 x 16.20 X 17.32 in.
(366 X 412 X 440 mm)
15.55 x 8.65 X 9.06 in.
(395 X 220 X 230 mm)
Dry Net Weight
40.8 lbs (15.0 Kg.)
55.1 lbs (25 Kg.)
50.7 lbs (23 Kg.)
Approx. 12 lbs (5.4 kg.)
Table 2. WC-62P/S Specifications
Height
59 in. (1,499 mm)
Width
51 in. (1,295 mm)
78 in. (1,983 mm)
8.82 cu. ft. (250 liters)
6.0 cu. ft. (170 liters)
(1/2 to 1 bag)
Length
Maximum Drum Capacity
Maximum Mixing Capacity
Bag Capacity
Weight - With Engine/ElectricMotor
680 lbs. (308 Kg.)
PAGE 6 —WC-62P/S CONCRETE MIXERS — PARTS & OPERATION MANUAL — REV. #7 (06/30/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
WC-62P/S CONCRETE MIXER — DIMENSIONS (MIXER)
See Table 2 for mixer dimensions
Figure 1. Mixer Dimensions
WC-62P/S CONCRETE MIXER — PARTS & OPERATION MANUAL — REV. #7 (06/30/05) — PAGE 7
Download from Www.Somanuals.com. All Manuals Search And Download.
WC-62P/S CONCRETE MIXER — SAFETY MESSAGE ALERT SYMBOLS
FORYOUR SAFETY ANDTHE SAFETY OF OTHERS!
HAZARD SYMBOLS
Safety precautions should be followed at all times when
operating this equipment. Failure to read and understand the
Safety Messages and Operating Instructions could result in
injury to yourself and others.
Rotating Parts
This Owner's Manual has been
developed to provide complete
instructions for the safe and efficient
NEVER operate equipment with covers, or
guards removed. Keep fingers, hands, hair and
clothing away from all moving parts to prevent
injury.
operation of the MQ Whiteman
ModelWC-62P (Plastic) and WC-
62S (Steel) Concrete Mixers.
Before using these mixers,
ensure that the operating
individual has read and
understands all instructions in
this manual.
Accidental Starting
ALWAYS place the circuit breaker or power
ON/OFF switch in the OFF position when the
pump is not in use.
SAFETY MESSAGE ALERT SYMBOLS
Sight and Hearing hazard
The three (3) Safety Messages shown below will inform you
about potential hazards that could injure you or others. The
Safety Messages specifically address the level of exposure to
the operator, and are preceded by one of three words: DANGER,
WARNING, or CAUTION.
ALWAYS wear approved eye and hearing
protection.
DANGER: You WILL be KILLED or
SERIOUSLY injured if you do not follow
directions.
Respiratory Hazard
ALWAYS wear approved respiratory
protection.
WARNING: You CAN be KILLED or
SERIOUSLY injured if you do not follow
directions.
Equipment Damage Messages
CAUTION: You CAN be injured if you
Other important messages are provided throughout this manual
to help prevent damage to your mixer, other property, or the
surrounding environment.
do not follow directions.
Potential hazards associated with the MQ Whiteman WC-62P/
WC-62S concrete mixers operation will be referenced with
Hazard Symbols which appear throughout this manual, and will
be referenced in conjunction with Safety Message Alert Symbols.
This mixer, other property, or the
surrounding environment could
be damaged if you do not follow
instructions.
PAGE 8 —WC-62P/S CONCRETE MIXERS — PARTS & OPERATION MANUAL — REV. #7 (06/30/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
WC-62P/S CONCRETE MIXER — RULES FOR SAFE OPERATION
■
NEVERtouchthehotexhaustmanifold,
muffler or cylinder.Allow these parts to
cool before servicing engine or mixer.
DANGER:
Failure to follow instructions in this manual may
lead to serious injury or even death! This
equipment is to be operated by trained and
qualified personnel only!This equipment is for
industrial use only.
The following safety guidelines should always be used when
operating the MQ Whiteman WC-62P/WC-62S Concrete Mixers:
■
■
HighTemperatures – Allow the engine to cool before adding
fuel or performing service and maintenance functions. Contact
with hot components can cause serious burns.
GENERAL SAFETY
■
DO NOT operate or service this equipment before
readingthisentiremanual.
The engine of this mixer requires an adequate free flow of
cooling air. NEVER! operate the mixer in any enclosed or
narrow area where free
■
■
This equipment should not be operated by
persons under 18 years of age.
flow of the air is restricted. If
the air flow is restricted it
will cause serious damage
to the mixer or engine and
NEVER operate this equipment without proper
protective clothing, shatterproof glasses, steel-
toed boots and other protective devices required
by the job.
may cause injury to people
and property. Remember
the
mixer's
engine
(gasoline models only)
gives off DEADLY gases.
■
■
NEVER operate this equipment when not feeling
well due to fatigue, illness or taking medicine.
■
■
ALWAYS refuel in a well-ventilated area, away from sparks
NEVER operate this equipment under the
influence or drugs or alcohol.
and open flames.
ALWAYS use extreme caution when working with flammable
liquids. When refueling, stop the engine and allow it to cool.
DO NOT smoke around or near the machine. Fire or explosion
could result from fuel vapors, or if fuel is spilled on a hot
engine.
■
■
■
Whenever necessary, replace nameplate, operation and
safety decals when they become difficult read.
■
NEVER operate the mixer in an explosive
atmosphere or near combustible
materials. An explosion or fire could result
causing severe bodily harm or even
death.
ALWAYS check the machine for loosened threads or bolts
before starting.
ALWAYS wear proper respiratory (mask) hearing and eye
protection equipment when operating the mixer.
■
■
Topping-off to filler port is dangerous, as it tends to spill fuel.
Refer to the Engine Owner's Manual for engine technical
questions or information.
■
■
NEVER use accessories or attachments, which are not
recommended by MQ Whiteman for this equipment. Damage
to the equipment and/or injury to user may result.
■
NEVER! place hands inside the drum while the drum is
rotating.
Manufacturer does not assume responsibility for any accident
due to equipment modifications.
WC-62P/S CONCRETE MIXER — PARTS & OPERATION MANUAL — REV. #7 (06/30/05) — PAGE 9
Download from Www.Somanuals.com. All Manuals Search And Download.
WC-62P/S CONCRETE MIXER — RULES FOR SAFE OPERATION
■
■
■
■
NEVER run engine without air cleaner.Severe engine damage
■
NEVER disconnect any "emergency or safety devices".
These devices are intended for operator safety. Disconnection
of these devices can cause severe injury, bodily harm or even
death! Disconnection of any of these devices will void all
warranties.
may occur.
ALWAYS read, understand, and follow procedures in
Operator’s Manual before attempting to operate equipment.
ALWAYS be sure the operator is familiar with proper safety
precautions and operations techniques before using roller.
■
■
If mixer is equipped with an electric motor, operate electric
motor only at the specified voltage indicated on the nameplate.
ALWAYS store equipment properly when it is not being used.
Equipment should be stored in a clean, dry location out of the
reach of children.
Make sure the OFF/ON power switch on the electric motor is
always in the OFF position before inserting the mixer's power
plug into an AC receptacle (electric model only).
■
■
■
■
NEVER leave the mixer unattended, turn off engine or electric
motor when unattended.
Maintenance Safety
■
NEVER lubricate components or attempt service on a running
machine.
CAUTION must always be observed while servicing this mixer.
Rotating parts can cause injury if contacted.
■
ALWAYS allow the machine a proper amount of time to cool
before servicing.
Unauthorized equipment modifications will void all
warranties.
■
■
Keep the machinery in proper running condition.
Ensure that any extension cable is protected against damage
and not liable to be tripped over or trapped underneath the
mixer.
Fix damage to the machine immediately and always replace
broken parts, or missing decals.
■
DO NOT allow extension cord to come into contact with water
■
■
■
Dispose of hazardous waste properly.Examples of potentially
hazardous waste are used motor oil, fuel and fuel filters.
or fluids.
■
■
DO NOT spray water onto electric motor.
DO NOT use food or plastic containers to dispose of
hazardous waste.
This mixer is intended for the production of concrete. Mixer
must be used only for its intended purpose.
DO NOT pour waste, oil or fuel directly onto the ground,
down a drain or into any water source.
■
This mixer is not suitable for the mixing of flammable or
explosive substances.
Emergencies
■
■
NEVER operate the mixer in an explosive atmosphere.
■
ALWAYS know the location of the nearest fire extinguisher
and first aid kit.
Before starting the mixer, check that all guards are in position
and correctly fitted.
■
Keep area around the mixer clear of obstructions which
could cause persons to fall onto moving parts.
■
■
ALWAYS ensure mixer is on level ground before mixing.
Become familiar with the controls of the mixer before
operating.
■
In emergencies always know the location of the
nearest phone or keep a phone on the job site.
Also know the phone numbers of the nearest
ambulance, doctor and fire department. This
information will be invaluable in the case of an
emergency.
■
■
ALWAYS replace any worn or damaged warning decals.
Ensure the drum is rotating while filling and emptying the
drum.
■
■
ALWAYS disconnect AC power plug from power source
before moving mixer (electric model only).
High Temperatures – Always stop engine and allow the
engine to cool before adding fuel, oil or performing service
and maintenance functions. Contact with hot components
can cause serious burns.
PAGE 10 —WC-62P/S CONCRETE MIXERS — PARTS & OPERATION MANUAL — REV. #7 (06/30/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
WC-62P/S CONCRETE MIXER — OPERATION AND SAFETY DECALS
Machine Safety Decals
The MQ Whiteman WC-62P and WC-62S mixers are equipped with a number of safety decals (Figure 1A). These decals are
provided for operator safety and maintenance information.The illustration below and on the next page shows these decals as they
appear on the machine.Should any of these decals become unreadable, replacements can be obtained from your dealer.
Figure 1A. WC-62P/S Mixer Decals
WC-62P/S CONCRETE MIXER — PARTS & OPERATION MANUAL — REV. #7 (06/30/05) — PAGE 11
Download from Www.Somanuals.com. All Manuals Search And Download.
WC-62P/S CONCRETE MIXER — GENERAL INFORMATION
Ensure that the extension cable is carefully laid out avoid-
Application
ing wet areas, sharp edges and locations where vehicles
might run over it. Avoid allowing the extension cable to be
trapped underneath the mixer.
This mixer is only intended for the production of concrete.
The mixer must be used for its intended purpose and is not
suitable for the mixing of flammable or explosive
substances. The mixer must not be used in an explosive
atmosphere. Use Table 4 (Mixing Hints) as a guide when
mixing concrete for various applications.
Unroll the extension cable fully or it will overheat and could
catch fire. Make sure that all extension cable connections
are dry and safe. Replace any defective or badly worn ex-
tension cable immediately.
Power Plants
The MQ Whiteman WC-62P and WC-62S mixers can be
powered by a variety of power plants or an electric motor.
Refer to Table 2 to for specific engine or electric motor data
information. All engines are air-cooled, 4-stroke gasoline
engines.
Hardware
Check all hardware on the mixer before starting. Periodically
inspect all hardware. Loose hardware can contribute to early
component failure and poor performance. UseTable 3 as general
guideline when the torqueing of mixer hardware is required.
Remember to keep all mixer hardware components tight.
Electrical
If mixer is equipped with an electric motor, make sure that
the power being supplied to the motor corresponds to the
voltage rating label on the motor.Supplying the wrong voltage
to the electric motor will cause severe electrical damage to
the motor.
Table 3. Hardware Torque
Recommendations
Hardware
Torque (ft-lbs)
Diameter
5/16-inch x 18
3/8-inch x 16
14
24
Always make sure the OFF/ON switch on the electric motor
is in the OFF position before applying power.
3/8-inch x 24
1/2-inch x 13
37
39
90
It is strongly recommended when inserting the mixer's
power cord into a receptacle, that a G.F.C.I. (Ground Fault
Current Interrupter) receptacle be used (115 VAC
applications).
1/2-inch x 13
(Grade 8)
Extension Cables
Engine Maintenance
The extension cable should be a 3-wire configuration that
includes a ground wire that conforms to UL code. The wire
cross section must be a minimum of 2.5 mm2 . Choose an
extension cord of adequate current carrying as Referenced
in Table 6. Remember distance affects the wire size of the
extension cable.
For basic engine maintenance, refer to the engine maintenance
section in this manual. For a more detailed engine maintenance,
refer to the Honda or Robin Engine Owner's manual furnished
with the engine.
Table 4. MIXING HINTS
BATCH QUANTITIES
SAND
APPROX. BATCH
OUTPUT
MIX
RATIOS
CEMENT 112 lbs.
(50 Kgs.)
STONE
CU. FT.
APPLICATIONS
Bag
CU. FT.
1-1/4
LTR
35
LTR
71
CU. FT.
3
LTR
85
1:2:4
1:3:6
1:4:8
1/2 BAG
1/3 BAG
1/4 BAG
2-1/2
2-1/2
2-1/2
Most Ordinary
Foundations
1-1/4
35
71
2-3/4
2-3/4
78
1-1/4
35
71
78
Rough Mass
Concrete
1:1-1/2:3
2/3 BAG
1-1/4
35
3
71
3
85
Watertight Floors,
Tanks, Pits, Etc.
PAGE 12 —WC-62P/S CONCRETE MIXERS — PARTS & OPERATION MANUAL — REV. #7 (06/30/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
WC-62P/S CONCRETE MIXER — MIXER BASIC COMPONENTS
Figure 2. Mixer Major Components
1.
2.
Steel Mixing Drum — The MQ Whiteman WC-62S uses
a 6 cu. ft steel mixing drum. This drum is to be used for
mixing of concrete. Always clean the drum after each use.
DO NOT use this mixing drum for the mixing of volatile
liquids.
8.
9.
Safety Chain — This mixer uses a 3/16-inch thick, 72-
inches long zinc-plated saftey chain.ALWAYS connect the
safety chain when towing.
Tow Bar — This mixer uses various towing bars, please
reference the frame assembly drawing and parts list in this
manual to determine which tow bar meets your
requirements.
Plastic Mixing Drum — The MQWhiteman WC-62P uses
a 6 cu. ft plastic mixing drum.This drum is to be used for
mixing of concrete. Always clean the drum after each use.
DO NOT use this mixing drum for the mixing of volatile
liquids.
10. Leaf Suspension — This mixer uses a leaf type
suspension. Check the mounting hardware for bolt hole
elongation and tightness. See maintenance section of this
manual for recommended maintenance.
3.
4.
5.
Mixing Blades (Plastic) — Used for the mixing concrete.
Replace blades when they show signs of wear.Reference
plastic mixing drum in the parts section of this manual.
11. Chock Blocks — Place these blocks (not included as
part of the mixer package) under each mixer wheel to
prevent rolling, when mixer is not connect to the towing
vehicle.
Dump Latch —To rotate the mixing drum, this latch must
be in the up position.To lock the drum, place the latch in the
down position.
12. Tires Ply — The tire ply (layers) number is rated in letters;
This mixer uses 13-inch 2-ply tires. Replace with only
recommended type tires.
Dump Gear Guard — NEVER operate the mixer with this
guard removed. Its purpose is to prevent dirt and debris
from entering the dump gear.In addition operator clothing
could become entangled in the dump gear, causing severe
injury and bodily harm.
13. ON/OFF Switch (gasoline only) —This switch is provided
on mixers with gasoline engines only and is located on
the side of the mixer frame. When activated it will shut
down the engine. Pull out when starting the engine.
6.
7.
Handwheel — Turn this wheel clockwise or counter-
clockwise to rotate the mixing drum. Remember the dump
latch must be in the up position in order for the mixing
drum to be rotated.
14. Cabinet/Latch — Encloses engine and electric motor.
NEVER run mixer with cabinet removed. Use latches to
secure engine compartment cabinet.
Zerk Fittings — There is, at the bottom and engine side
of the yoke, and center of the handwheel grease zerk
fittings. Lubricate these fittings as referenced in the
maintenance section of this manual.
15. Mixing Blades (Steel) — Used for the mixing of concrete.
When blades show signs of wear, entire steel mixing drum
assembly must be replaced. See steel mixing drum
assembly in the parts section of this manual.
WC-62P/S CONCRETE MIXER — PARTS & OPERATION MANUAL — REV. #7 (06/30/05) — PAGE 13
Download from Www.Somanuals.com. All Manuals Search And Download.
WC-62P/S CONCRETE MIXER — BASIC ENGINE COMPONENTS
Honda GX Series Engine Shown
Figure 3. Engine Controls and Components
5. FuelValve Lever – OPEN to let fuel flow, CLOSE to stop
INITIAL SERVICING
the flow of fuel.
The engine (Figure 3) must be checked for proper lubrication and
filled with fuel prior to operation. Refer to the manufacturers Engine
manual for instructions & details of operation and servicing.
6. Choke Lever – Used in the starting of a cold engine, or in
cold weather conditions. The choke enriches the fuel
mixture.
7. Air Cleaner – Prevents dirt and other debris from entering
the fuel system. Remove wing-nut on top of air filter
cannister to gain access to filter element.
1. Fuel Filler Cap – Remove this cap to add unleaded
gasoline to the fuel tank. Make sure cap is tightened
securely. DO NOT over fill.
NOTE
WARNING
WARNING
Operating the engine without an air filter,
with a damaged air filter, or a filter in need of
replacement will allow dirt to enter the
engine, causing rapid engine wear.
Adding fuel to the tank should be accomplished only
when the engine is stopped and has had an
opportunity to cool down. In the event of a fuel spill,
DO NOT attempt to start the engine until the fuel residue has been
completely wiped up, and the area surrounding the engine is dry.
8. Spark Plug – Provides spark to the ignition system. Set
spark plug gap to 0.6 - 0.7 mm (0.028 - 0.031 inch). Clean
spark plug once a week.
2. Throttle Lever – Used to adjust engine RPM speed (lever
advanced forward SLOW, lever back toward operator
FAST).
9. Muffler – Used to reduce noise and emissions.
WARNING
3. Engine ON/OFF Switch – ON position permits engine
Engine components can generate extreme heat.
To prevent burns, DO NOT touch these areas
while the engine is running or immediately after operating. NEVER
operate the engine with the muffler removed.
starting, OFF position stops engine operations.
4. Recoil Starter (pull rope) – Manual-starting method. Pull
the starter grip until resistance is felt, then pull briskly and
smoothly.
10. Fuel Tank – Holds unleaded gasoline. For additional
information refer to engine owner's manual.
PAGE 14 —WC-62P/S CONCRETE MIXERS — PARTS & OPERATION MANUAL — REV. #7 (06/30/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
WC-62P/S CONCRETE MIXER — HANDWHEEL ASSEMBLY
Assembly
TheWC-62P andWC-62S concrete mixers are shipped with
the handwheel detached. Attach the handwheel to the mixer
as shown in Figure 4.
Figure 4. Handwheel Assembly
WC-62P/S CONCRETE MIXER — PARTS & OPERATION MANUAL — REV. #7 (06/30/05) — PAGE 15
Download from Www.Somanuals.com. All Manuals Search And Download.
WC-62P/S CONCRETE MIXER —TOWING GUIDELINES
■
■
■
■
Check wheel mounting lug nuts with a torque wrench.
Torque wheel lug nuts as described in the maintenance
section of this manual.
Towing Safety Precautions
CAUTION:
Check tightness of U-clamp nuts, torque suspension
hardware as referenced in the maintenance section of this
manual.
■
Check with your county or state safety
towing regulations department before
towing your mixer.
Avoid sudden stops and starts.This can cause skidding, or
jackknifing. Smooth, gradual starts and stops will improve
gas milage.
To reduce the possibility of an accident while transporting
the mixer on public roads, always make sure that the mixer
towing components and the towing vehicle are in good
operating condition and both units are mechanically sound.
Avoid sharp turns to prevent rolling.
CAUTION:
The following list of suggestions should be used when towing
the mixer:
If the mixer tow bar is deformed or damaged
replace entire tow bar. NEVER tow the mixer
with a defective tow bar. There exist the
possibility of the trailer separating from the
towing vehicle.
■
Make sure that the hitch and coupling of the towing vehicle
are rated equal to, or greater than the trailer "gross vehicle
weight rating" (GVWR).
■
■
■
■
■
■
ALWAYS inspect the hitch and coupling for wear. NEVER
Tow Bar to Vehicle Connection (Coupler Only)
tow the mixer with defective hitches, couplings, chains etc.
1. Check the vehicle hitch ball, and mixer's coupler for
signs of wear or damage. Replace any parts that are
worn or damaged before towing.
CHECK the tire air pressure on both the towing vehicle and
the trailer.Also check the tire tread wear on both vehicles.
ALWAYS make sure the mixer is equipped with a "Safety
Chain".
2. Use only a 2-inch ball diameter (towing vehicle), this
will match the mixer's 2-inch coupler. Use of any other
ball diameter will create an extremely dangerous condition
which can result in separation of the coupler and ball or
ball failure.
ALWAYS attach trailer's safety chain to the frame of towing
vehicle.
ALWAYS make sure that the towing vehicle's directional,
backup, and brake lights are working properly.
3. After tow bar has been connected to mixer (see next
page), attach mixer's coupler to the hitch ball on the
towing vehicle securely and make sure the lock lever
is in the down position (locked).
Remember in most cases the maximum speed unless
otherwise posted for highway towing is 45 MPH, however
before towing your mixer, check your local state, and county
vehicle towing requirements. Recommended off-road towing
is not to exceed 10 MPH or less depending on type of terrain.
■
■
■
■
Place chocked blocks underneath wheels to prevent rolling,
Mixer Tow Bar Vehicle Connection (Pintle and Loop)
while parked, if disconnected from towing vehicle.
1. Make sure the bumper on the towing vehicle is equipped
to handle either a pintle or loop type tow bar configuration.
Inflate tires to correct pressure, inspect tires for cuts, and
excessive wear. See Table 16 (Tire Wear Troubleshooting).
2. After tow bar has been connected to mixer (see next
page), secure either type of tow bar to the towing vehicle,
following state and county towing regulations.
When towing of the mixer is required, place the drum in the
up position (mouth facing upwards).
ALWAYS make sure that the fuel valve lever is in the OFF
position (gasoline models only).
3. As a minimum, use a 1/2-inch bolt and nylock nut grade
5 when securing either tow bar to the towing vehicle,
PAGE 16 —WC-62P/S CONCRETE MIXERS — PARTS & OPERATION MANUAL — REV. #7 (06/30/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
WC-62P/S CONCRETE MIXER — SAFETY CHAIN CONNECTION
2. Route the safety chain through the holes just above the
CAUTION:
tow bar, located on each side of the mixer stand.
NEVER ! tow the mixer with the safety chain
removed. The safety chain is intended to
prevent complete separation of the mixer from
the towing vehicle in the event of a tow bar
failure.
Loop the chain together and place under the tow bar.
Secure the loop with the connector link.
3. Extend the safety chain along the length of the tow bar,
looping it through the tow bar's connector link. Remove
any excess chain slack.
Reference Figure 5 for the installation of the Saftey Chain.
4. Connect the free end of (connector link) the safety chain
to the towing vehicle. Remember it is critical that the
length of the chain be properly adjusted, to prevent
the draw bar and the front of the mixer stand from
dropping to the the ground (contact) in the event the
draw bar becomes disconnected from the towing vehicle.
Tow Bar to Mixer Connection
1. Insert the tow bar through the round opening at the
bottom of the mixer stand.
Align the hole on the tow bar with the hole on the mixer
frame, and insert 1/2-inch bolt through tow bar and frame.
Secure tow bar to frame with 1/2-inch nylock nut.Tighten
to 40 ft.-lbs.
Figure 5. Tow Bar and Safet
WC-62P/S CONCRETE MIXER — PARTS & OPERATION MANUAL — REV. #7 (06/30/05) — PAGE 17
Download from Www.Somanuals.com. All Manuals Search And Download.
WC-62P/S CONCRETE MIXER — ELECTRIC MOTOR
Electric Motor
Electric MotorVoltage Change Switch
For maintenance care and operation of the electric motor, refer
to your electric motor instruction booklet furnished with the electric
motor.
1.
ALWAYS make certain the electric motor's ON/OFF switch
is in the "OFF" position and the power cord has been
disconnected from the power source.
2.
Remove the voltage change lock-out bolt and nut (Figure 6).
Change the position of the voltage change toggle switch
from 115VAC to 230VAC.The mixer is factory wired for 115
VAC operation.
Protect the electric motor from dust as much as possible and
keep ventilating openings clean.
CAUTION:
■
■
DO NOT spray water at any time on the
electric motor.
3.
Re-install the voltage change lock-out bolt and nut.
DO NOT operate electric motor in a
explosive environment.
The electric motor used in this mixer is a single-phase 1.5 HP
motor. The input voltage requirement for this motor is either 115
or 230 VAC only.
Electric Motor Connection
A 12 inch electrical cable (Figure 2) with a pigtail at one end is
provided with the electrical motor for hookup to a power source.
Table 1. shows the required NEMA connector for the desired
motor horsepower rating. In addition, Table 2 also shows the
matching NEMA approved connector for the required extension
cord.
Figure 6. Voltage Change Switch
4.
Important!, when changing the input voltage to the electric
motor from 115 to 230VAC, the plug on the electric motor
power cord must also be changed. SeeTable 6 and Figure 7.
ALWAYS, make certain that the power source required for the
electric motor is correct and always use the correct NEMA
configuration plug. Failure to supply the correct voltage to the
motor can severely damage the motor.
Table 6. Electric Motor Wiring Information
The electric motor supplied with the mixer is configured from the
factoryfor115VACgroundedoperation.Makecertainthatthecorrect
size grounded (3-wires) extension cord is used.SeeTable 5.
Motor
Horsepower
Rating
115-230 VAC - Single Phase
NEMA Plug Connector
Mating NEMA
Receptacle Connector
Motors can burn out when the line voltage falls 10% below the
voltage rating of the motor. Failure to use proper voltage will
cause the motor to overheat and actuate the overload switch.
1.5 HP
(115 VAC)
L5-20P P/N EM940537
L6-20P P/N 940539
L5-20R P/N EM940538
1.5 HP
(230 VAC)
L6-20R P/N 940540
If overload protection should actuate because of improper voltage
or any other malfunction, turn the main switch on the motor to the
"OFF" position and correct the problem, press the reset switch
button, and turn the main switch to the "ON" position.
NEVER! disable or disconnect the
ON/OFF switch on the electric motor.
It is provided for operator safety.Injury
may result if it is disable, disconnected
or improperly maintained.
Table 5. Recommended Extension Cord Size
s
Electric
Motor
Input
50 ft.
75 ft.
100 ft.
200 ft.
Voltage (15.24 m) (22.86 m) (30.48 m) (60.96 m)
115 VAC
230 VAC
No. 12
No. 14
No. 10
No. 12
No. 8
No. 6
No. 8
1.5 HP
No. 12
PAGE 18 —WC-62P/S CONCRETE MIXERS — PARTS & OPERATION MANUAL — REV. #7 (06/30/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
WC-62P/S CONCRETE MIXER — ELECTRIC MOTOR
Figure 7. Single Phase Electric Motor with 12 inch Pigtail Cable
WC-62P/S CONCRETE MIXER — PARTS & OPERATION MANUAL — REV. #7 (06/30/05) — PAGE 19
Download from Www.Somanuals.com. All Manuals Search And Download.
WC-62P/S CONCRETE MIXER — PRE-INSPECTION (GAS ENGINE)
Before Starting
Table 7. Oil Type
Temperature
1. Read safety instructions at the beginning of manual.
Season
Summer
Spring/Fall
Winter
Oil Type
SAE 10W-30
SAE 10W-30/20
SAE 10W-10
2. Clean the mixer, removing dirt and dust, particularly the
25°C or Higher
25°C~10°C
engine cooling air inlet, carburetor and air cleaner.
3. Check theairfilterfor dirtanddust. Ifairfilterisdirty,replace
air filter with a new one as required.
0°C or Lower
4. Check carburetor for external dirt and dust. Clean with dry
compressedair.
Explosive Fuel
5. Checkfasteningnutsandboltsfortightness.
Fuel Check
Engine Oil Check
If your mixer has a gasoline engine, determine if the engine fuel
is low. If fuel is low, remove the fuel filler cap and fill with unleaded
gasoline. Motor fuels are highly flammable and can be dangerous
if mishandled. DO NOT smoke while refueling. DO NOT attempt
to refuel the trowel if the engine is hot! or running.
1. To check the engine oil level, place the mixer on
secure level ground with the engine stopped.
2. Remove the filler dipstick from the engine oil filler hole
(Figure 8) and wipe it clean.
1. Remove the gasoline cap located on top of fuel tank.
2. Visuallyinspecttoseeiffuellevelislow. Iffuelislow,replenish
with unleaded fuel.
3. When refueling, be sure to use a strainer for filtration. DO
NOT top-off fuel. Wipe up any spilled fuel.
V-belt Check
A worn or damagedV-belt can adversely affect the performance
of the mixer.If aV-belt is defective or worn simply replace the V-
belt as outlined in the maintenance section of this manual.
Figure 8. Engine Oil Dipstick (Removal)
Blade Check
3. Insert and remove the dipstick without screwing it into the
filler neck. Check the oil level shown on the dipstick.
Check for worn blades. If using a steel tub and the blades are
worn, replace the entire tub assembly. Remember the blades
are welded to tub.
4. If the engine oil level is low (Figure 9), fill to the edge of
the oil filler hole with the recommended oil type (Table 7).
See Table 2 for the oil capacity of your type engine.
If using a plastic tub, replace the blades using the part numbers
referenced in the parts section of this manual.
Start/Stop Switches
This mixer has been equipped with a start/stop switches for both
the gasoline and electric motor mixers.These switches should be
tested every time the engine or motor is started.
Grease Fittings (Zerk)
Check the zerk grease fittings (Figure 27) as shown in the
maintenancesectionofthismanual.Thesegreasefittingslubricate
the handwheel and the yoke mechanism.
Figure 9. Engine Oil Dipstick (Oil Level)
PAGE 20 —WC-62P/S CONCRETE MIXERS — PARTS & OPERATION MANUAL — REV. #7 (06/30/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
WC-62P/S CONCRETE MIXER — INITIAL START-UP (GAS ENGINE)
Starting the Engine (Gasoline Only)
4.
Turn the engine switch (Figure 13) to the ON position.
The following steps outline the procedure for starting the engine.
Depending on the type of engine employed in the mixer the
steps may vary slightly. If your mixer has an electric motor
disregard this section.
1.
Move the fuel shut-off lever (Figure 10) to the ON position.
Figure 13. Engine ON/OFF Switch
5.
Located at the rear of the mixer frame is the main start/
stop button (Figure 14). Pull this button outward to start the
engine.
Figure 10. Fuel Shut-OFF Lever
2.
To start a cold engine, move the choke lever (Figure 11) to
the CLOSED position.
Figure 14. Engine Start/Stop Button
6.
Pull the starter grip (Figure 15) lightly until you feel
resistance, then pull briskly.The drum should be rotating at
this time.
Figure 11. Choke Lever
3.
Move the throttle lever (Figure 12) away from the slow
position, about 1/3 of the way toward the fast position.
Figure 15. Starter Grip
Figure 12. Throttle Lever
WC-62P/S CONCRETE MIXER — PARTS & OPERATION MANUAL — REV. #7 (06/30/05) — PAGE 21
Download from Www.Somanuals.com. All Manuals Search And Download.
WC-62P/S CONCRETE MIXER — INITIAL START-UP (ELECTRIC MOTOR)
5. Placethevoltageselectorswitch(Figure17)intheposition
thatisinaccordancewithvoltagelistedontheelectricmotor's
nameplate.Theelectricmotor'sareshippedfromthefactory
withthewiththevoltageselectorswitchplacedinthe115VAC
position.
Initial Start-up Instructions (Electric Motor)
Starting
CAUTION:
DO NOT attempt to operate the mixer until
the Safety, General Information and
Inspection sections have been read and
understood.
If230VACisrequired, removethelockingboltandnutand
flip the voltage selector toggle switch to the 230 VAC
position. Reinstall the locking bolt and nut to prevent the
toggle switch from being accidently tripped.
1. Before starting, make sure mixer is positioned on a secure
flat surface to prevent rolling.
2. Use an extension cord (see Table 5) of adequate current
carryingcapacity,insert theelectricmotor'spowerplug into
one end of the extension cord.
3. NEVER! use a worn or frayed extension cord.
4. NEVER! operate mixer withV-belt cover removed.
DANGER
NEVER! touch the power cord (Figure 16)
with wet hands or while standing in water
when it is connected to a power source.The
possibly exists of electrical shock
(electrocution) even death. NEVER! spray
water directly on the electric motor.
Figure 17. Voltage Change Switch
(115 VAC Position)
6. Plugtheotherendoftheextensioncordintoeithera115 or
230VAC power source (look at position of voltage selector
switch). Remembertoreadthenameplatetodeterminethe
motor'sinputvoltagerequirement.
WARNING:
ALWAYS read the label on the electric motor
before applying power.The label will indicate
the correct power requirements for the motor.
Remember the use of an incorrect input
voltage will severely damage the electric
motor.
Starting the Electric Motor
Figure 16. Extension Cord (Wet Hands)
1.
Set the electric motor's ON/OFF switch (Figure 18) to the
ON position.
To prevent personnel from tripping over
the extension cord, position the
extension cord so that it lays flat and is
not curled underneath the mixer.
NOTE
Figure 18. Electric Motor ON/OFF Switch
(ON Position)
PAGE 22 —WC-62P/S CONCRETE MIXERS — PARTS & OPERATION MANUAL — REV. #7 (06/30/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
WC-62P/S CONCRETE MIXER — OPERATION
3. Placingtheshovelallthewayinsidethedrum(Figure21)will
causetheshoveltostriketheblades.Thisconditionwillmake
Operation
1. Topositionthetub,makesurethemixerisplacedonfirmlevel
ground,thenpulluponthedumplatch(Figure19)andturn
thehandwheeluntilthetubisatthedesiredposition.Once
thetubisatthedesiredposition,pulldownonthedumplatch
to lock the tub in position.
the shovel rotate, and could cause injury to personnel.
NEVER place hands inside the mixing drum while it is
rotating.
Figure 21. Filling Mixing Drum
Stopping the Mixer (Gasoline)
1.
Push the main start/stop switch (Figure 22) inward to stop
the engine.
Figure 19. Mixing Drum Positioning
CAUTION:
NEVER stand in front or behind the mixing
drum while it is being placed in the dump
position. Stay clear of the mixing drum while
it is being positioned.
Figure 22. Start/Stop Button (Stop Position)
2.
3.
Place fuel shut-off lever in the OFF position.
2. As the drum rotates, use a shovel (Figure 20) to place the
cementmixinsidethedrum,addwaterasrequired.Becareful
to only place the tip of the shovel inside the drum.
Clean drum of all debris and foreign matter.
Stopping the Mixer (Electric)
1.
Place the electric motor's ON/OFF switch (Figure 23) in
the OFF position.
Figure 23. Electric Motor ON/OFF Switch
(OFF Position)
2.
3.
Disconnect the electric motor's extension cord from its
power source.
Figure 20. Filling Mixing Drum
Clean drum of all debris and foreign matter.
WC-62P/S CONCRETE MIXER — PARTS & OPERATION MANUAL — REV. #7 (06/30/05) — PAGE 23
Download from Www.Somanuals.com. All Manuals Search And Download.
WC-62P/S CONCRETE MIXER — MAINTENANCE (ENGINE)
UseTable 8 as a general maintenance guideline when servicing
your engine. For more detail engine maintenance information,
refer to the engine owner's manual supplied with your engine.
Table 8. Engine Maintenance Schedule
FIRST
EVERY
EVERY
EVERY
YEAR
OR
EVERY
2 YEARS
OR
MONTH 3 MONTHS 6 MONTHS
OR
DESCRIPTION (3)
OPERATION
BEFORE
OR
OR
10 HRS.
25 HRS.
50 HRS.
100 HRS.
200 HRS.
CHECK
CHANGE
CHECK
X
Engine Oil
X
X
X
Air Cleaner
All Nuts & Bolts
Spark Plug
CHANGE
X (1)
Re-tighten If
Necessary
CHECK-CLEAN
REPLACE
CHECK
X
X
X
Cooling Fins
Spark Arrester
Fuel Tank
CLEAN
X
X
CLEAN
Fuel Filter
CHECK
X
Idle Speed
CHECK-ADJUST
CHECK-ADJUST
CHECK
X (2)
Valve Clearance
Fuel lines
X (2)
Every 2 years (replace if necessary) (2)
(1) Service more frequently when used in DUSTY areas.
(2) These items should be serviced by your service dealer, unless you have the proper tools and are mechanically
proficient. Refer to the HONDA or ROBIN Shop Manual for service procedures.
(3) For commercial use, log hours of operation to determine proper maintenance intervals.
PAGE 24 —WC-62P/S CONCRETE MIXERS — PARTS & OPERATION MANUAL — REV. #7 (06/30/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
WC-62P/S CONCRETE MIXER — MAINTENANCE (ENGINE)
DANGER :
Maintenance
Perform the scheduled maintenance procedures as defined by
Table 6 and below:
DO NOT use gasoline as a cleaning solvent,
because that would create a risk of fire or
explosion.
DAILY
■
Thoroughly remove dirt and oil from the engine and control
area.Clean or replace the air cleaner elements as necessary.
Check and retighten all fasteners as necessary. Check the
gearbox for oil leaks. Repair or replace as needed.
ENGINEAIRCLEANER
WEEKLY
1. Remove the air cleaner cover and foam filter element as
shown in Figure 26.
■
Remove the fuel filter cap and clean the inside of the fuel
tank.
2. Tap the paper filter element (Figure 34) several times on a
hard surface to remove dirt, or blow compressed air [not
exceeding 30 psi (207 kPa, 2.1 kgf/cm2)] through the filter
elementfromtheaircleanercaseside.NEVER brushoffdirt.
Brushingwillforcedirtintothefibers.Replacethepaperfilter
element if it is excessively dirty.
■
■
Remove or clean the filter at the bottom of the tank.
Remove and clean the spark plug (Figure 24), then adjust
the spark gap to 0.024 ~0.028 inch (0.6~0.7 mm).This unit
has electronic ignition, which requires no adjustments.
3. Cleanfoamelementinwarm,soapywaterornonflammable
solvent. Rinseanddrythoroughly. Diptheelementinclean
engineoilandcompletelysqueezeouttheexcessoilfromthe
element before installing.
Figure 24. Spark Plug Gap
ENGINEOIL
1. Drain the engine oil when the oil is warm as shown in
Figure 25.
2. Remove the oil drain bolt and sealing washer and allow
the oil to drain into a suitable container.
3. Replace engine oil with recommended type oil as listed
in Table 7. For engine oil capacity, see Table 2 (engine
specifications). DO NOT overfill.
4. Install drain bolt with sealing washer and tighten se-
curely.
Figure 26. Engine Air Cleaner
Figure 25. Engine Oil (Draining)
WC-62P/S CONCRETE MIXER — PARTS & OPERATION MANUAL — REV. #7 (06/30/05) — PAGE 25
Download from Www.Somanuals.com. All Manuals Search And Download.
WC-62P/S CONCRETE MIXER — MAINTENANCE (MIXER)
2.
Use Poleyrex EM (Exxon Mobil) or equalivant lubricant.
Clean grease fitting, apply grease gun to fitting (1/2 shot).
Remember too much grease or injecting grease too quickly
can cause premature bearing failure. Slowly apply the
recommended amount of grease, taking a miniute or so to
apply.
Ball Socket and Clamp Face Maintenance
1.
If the towing vechicle is equipped with a ball socket, smear
socket periodically with multi-purpose grease. This will keep
the ball socket well lubricated.
2.
3.
Periodically oil pivot points and clamp face surfaces of
coupler with SAE 30 WT.motor oil.
Wheel Bearings
1. After every 3 months of operation, remove the hub dust cap
When parking or storing your mixer. Keep the coupler off
the ground so dirt will not build up in the ball socket.
and inspect the wheel bearings (Figure 29). Once a year,
or when required, disassemble the wheel hubs remove
the old grease and repack the bearings forcing grease
between rollers, cone and cage with a good grade of high
speed wheel bearing grease (never use grease heavier
than 265 A.S.T.M.penetration (“No.2.”)
Grease Fittings (Zerk) Maintenance (Mixer)
There are 3 grease (Figure 27) fittings that will require
lubrication. Lubricate these fittings once a week. Use lithium
base grease, grade N0.1.
Figure 29. Wheel Hub and Bearings
Figure 27. Grease Fittings Mixer
2.
Fill the wheel hub (Figure 29) with grease to the inside
diameter of the outer races and also fill the hub grease cap.
Reassemble the hub and mount the wheel. Then tighten
the adjusting nut, at the same time turn the wheel in both
directions, until there is a slight bind to be sure all the
bearing surfaces are in contact.
Grease Fittings (Zerk) Maintenance (Electric Motor)
1.
There are two grease (Figure 28) fittings at each end of the
electric motor that will require lubrication. Lubricate these
fittings about every 16 months.
Then back-off the adjusting nut 1/6 to 1/4 turn or to the
nearest locking hole or sufficiently to allow the wheel to
rotate freely within limits of .001" to .010" end play.Lock the
nut at this position. Install the cotter pin and dust cap, and
tighten all hardware.
Mixer Cleaning
1.
For thorough mix and longer drum life, always wash drum
out after each use.
2.
NEVER! pour or spray water over the engine or electric
motor.
Figure 28. Grease Fittings Electric Motor
PAGE 26 —WC-62P/S CONCRETE MIXERS — PARTS & OPERATION MANUAL — REV. #7 (06/30/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
WC-62P/S CONCRETE MIXER — MAINTENANCE (MIXER)
Tires/Wheels/Lug Nuts
Tires and wheels are a very important and critical compo-
nents of the trailer. When specifying or replacing the trailer
wheels it is important the wheels, tires, and axle are prop-
erly matched.
CAUTION:
DO NOT attempt to repair or modify a
wheel. DO NOT install an inter-tube to
correct a leak
through the rim.
If the rim is cracked, the air
pressure in the inter-tube may
cause pieces of the rim to explode
(break-off) with great force and
can cause serious eye or bodily
injury.
Suspension
The leaf suspension springs and associated components
(Figure 30) should be visually inspected every 6,000 miles
for signs of excessive wear, elongation of bolt holes, and
loosening of fasteners. Replace all damaged parts (sus-
pension) immediately. Torque locknut securing U-clamp to
spring leaf between 45 and 50 ft.-lbs.
Tires Wear/Inflation
Tire inflation pressure is the most important factor in tire
life. Pressure should be checked cold before operation. DO
NOT bleed air from tires when they are hot. Check inflation
pressure weekly during use to insure the maximum tire life
and tread wear.
Table 9 (Tire Wear Troubleshooting) will help pinpoint the
causes and solutions of tire wear problems.
CAUTION:
ALWAYS wear safety glasses
when removing or installing force
fitted parts. Failure to comply may
result in serious injury.
Figure 30. Suspension Components
WC-62P/S CONCRETE MIXER — PARTS & OPERATION MANUAL — REV. #7 (06/30/05) — PAGE 27
Download from Www.Somanuals.com. All Manuals Search And Download.
WC-62P/S CONCRETE MIXER — MAINTENANCE (MIXER)
Lug NutTorque Requirements
It is extremely important to apply and maintain proper wheel
mounting torque on the trailer. Be sure to use only the fas-
teners matched to the cone angle of the wheel. Proper pro-
cedure for attachment of the wheels is as follows:
1. Start all wheel lug nuts by hand.
2. Torque all lug nuts in sequence. See Figure 31. DO NOT
torquethewheellugnutsallthewaydown.Tighteneachlug
nut in 3 separate passes as defined by Table 10.
3. Afterfirstroaduse,retorquealllugnutsinsequence.Check
all wheel lug nuts periodically.
NEVER! use an pneumatic air gun
to tighten wheel lug nuts.
Mixer Storage
For storage of the mixer for over 30 days, the following is
recommended:
z
Drain the fuel tank completely, or add STA-BIL to the
fuel.
z
z
Run the engine until the fuel is completely consumed.
Completely drain used oil from the engine crankcase
and fill with fresh clean oil, then follow the procedures
described in the engine manual for engine storage.
z
z
Clean the entire mixer and engine compartment.
Place the mixing drum in the down position (mouth facing
downward).
z
Cover the mixer and place it a clean dry area, that is
protected from harsh elements.
Figure 31. Wheel Lug Nuts Tightening Sequence
PAGE 28 —WC-62P/S CONCRETE MIXERS — PARTS & OPERATION MANUAL — REV. #7 (06/30/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE PAGE
WC-62P/S CONCRETE MIXER — PARTS & OPERATION MANUAL — REV. #7 (06/30/05) — PAGE 29
Download from Www.Somanuals.com. All Manuals Search And Download.
WC-62P/S CONCRETE MIXER — TROUBLESHOOTING (ENGINE)
diagnosis based on the Troubleshooting (Tables 10 and 11)
information shown below and on the next page. If the problem
cannot be remedied, please leave the unit just as it is and
consult our company's business office or service plant.
Practically all breakdowns can be prevented by proper
handling and maintenance inspections, but in the event of a
breakdown, please take a remedial action following the
TABLE 10. ENGINE TROUBLESHOOTING
SYMPTOM
Difficult to start
POSSIBLE PROBLEM
SOLUTION
Ignition plug being bridge?
Carbon deposit at ignition?
Check ignition system.
Clean or replace ignition.
Replace insulators.
Fuel is available but spark plug
will not ignite. (Power available
at high tension cable).
Short circuit due to defective
insulators?
Improper spark gap?
Set spark plug gap to the correct gap.
Check stop switch circuit. Replace stop switch if defective.
Replace ignition coil.
Short circuit at stop switch?
Ignition coil defective?
Fuel is available but spark plug
will not ignite. (Power NOT
available at high tension cable).
Muffler clogged with carbon
deposits?
Clean or replace muffler.
Fuel is available and spark plug
ignites (compression normal).
Fuel in use inadequate (water,
dust)?
Flush fuel sytem and replace with fresh fuel.
Air Cleaner clogged?
Defective cylinder head gasket?
Cylinder worn?
Clean or replace air cleaner.
Tighten cylinder head bolts or replace head gasket.
Replace cylinder.
Fuel is available and spark plug
ignites (compression low ).
Spark plug loose?
Tighen spark plug.
Operation not satisfactory
Air cleaner clogged?
Air in fuel line?
Bleed (remove air) from fuel line.
Adjust carbureator float
Not enough power available
(compression normal, no miss-
firing).
Fuel level in carbureator float
chamber improper?
Carbon deposits in cylinder?
Ignition coil defective?
Clean or replace cylinder
Flush fuel sytem and replace with fresh fuel.
Replace ignition wires, clean ignition.
Flush fuel sytem and replace with fresh fuel.
Not enough power available
(compression normal, miss-
firing).
Ignition plug often shorts?
Fuel in use inadequate (water,
dust)?
Excessive carbon depostion in
combustion chamber?
Clean or replace crankcase.
Clean or replace muffler.
Engine overheats.
Exhaust or muffler clogged with
carbon.
Spark plug heat value incorrect? Replace spark plug with correct type spark plug.
PAGE 30 —WC-62P/S CONCRETE MIXERS — PARTS & OPERATION MANUAL — REV. #7 (06/30/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
WC-62P/S CONCRETE MIXER — TROUBLESHOOTING (ENGINE/MIXER)
TABLE 10. ENGINE TROUBLESHOOTING (Continued)
SYMPTOM
POSSIBLE PROBLEM
SOLUTION
Operation not satisfactory
Governor adjustment improper?
Governor spring defective?
Fuel flow erratic?
Adjust governor to correct lever.
Clean or replace ignition.
Check fuel line.
Rotational speed fluctuates.
Air taken in through suction
line?
Check suction line.
Dust in rotating part?
Spring spring failure?
Clean recoil starter assembly.
Replace sprial spring.
Recoil starter not working
properly.
TABLE 11. MIXER TROUBLESHOOTING
SYMPTOM
POSSIBLE PROBLEM
SOLUTION
Check that the ring gear and bearings are not worn . Replace as
necessary.
Defective ring gear?
Check that the pinion gear and bearings are not worn . Replace as
necessary.
Defective pinion gear?
Drum rotates rough.
Worn V-belt?
Loose pulley?
Replace V-belt.
Tighten or replace pulley.
Incorrect or no voltage being
supplied to electric motor?
Check that the electric motor has the correct supply voltage.
Inspect power source and extension cord. Push reset button on
electric motor. Make sure correct voltage is being supplied to motor.
Power to electric motor?
Fuel?
Check level of fuel in fuel tank. Add fuel if necessary. Make sure
fuel is being supplied to the engine. Check to ensure that the fuel
filter is not clogged.
Drum does not rotate at all.
Broken V-belt?
Replace V-belt.
Check that the gears and bearings are not broken. Replace as
necessary.
Defective ring or pinion gears?
Defective electric motor?
Replace electric motor.
WC-62P/S CONCRETE MIXER — PARTS & OPERATION MANUAL — REV. #7 (06/30/05) — PAGE 31
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLANATION OF CODE IN REMARKS COLUMN
How to read the marks and remarks used in this parts
book.
The contents of this parts
catalog are subject to change
without notice.
NOTE
Items Found In the “Remarks” Column
Serial Numbers-Where indicated, this indicates a serial
number range (inclusive) where a particular part is used.
Model Number-Where indicated, this shows that the
corresponding part is utilized only with this specific model
number or model number variant.
Items Found In the “Items Number” Column
All parts with same symbol in the number column, , #,
+
, %, or
*
>
, belong to the same assembly or kit.
If more than one of the same
reference number is listed, the
last one listed indicates newest
(or latest) part available.
NOTE
PAGE 32 —WC-62P/S CONCRETE MIXERS — PARTS & OPERATION MANUAL — REV. #7 (06/30/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
WC-62P/S CONCRETE MIXER — SUGGESTED SPARE PARTS
WC62P/S CONCRETE MIXERS 1 TO 4 UNITS WITH
HONDA GX160K1HX2, GX240K1HA2 AND ROBIN EH25-
2YR000
Qty. P/N
Description
2 ....... 503859 .............. V-BELT w/GAS ENGINE
2 ....... EM900267 ......... V-BELT w/ELECTRIC MOTOR
1 ....... EM940734 ......... STOP BUTTON w/GAS ENGINE
2 ....... 491010 .............. LATCH SET
1 ....... 505390 .............. EXPANSION PLUG
2 ....... EM903026 ......... SPINDLE BEARING CUP
2 ....... EM903063 ......... SPINDLE BEARING CONES
1 ....... EM505472 ......... SPACER, DRUM
2 ....... 492179 .............. BEARING JACKSHAFT
2 ....... EM914288 ......... SEAL, AXLE
2 ....... EM903012 ......... BEARING CUP
2 ....... EM903049 ......... BEARING CONE, 7/8" SPINDLE
2 ....... EM903113 ......... BEARING CONE, 1-1/16 SPINDLE
2 ....... 3469 .................. DUST CAP, AXLE
4 ....... 17210ZE1517 .... ELEMENT, AIR HONDA GX160
4 ....... 17210ZE2515 .... ELEMENT, AIR HONDA GX240
4 ....... 2703261008....... ELEMENT, AIR ROBIN EH-25
4 ....... 9807956846....... SPARK PLUG HONDA
4 ....... 0650140150....... SPARK PLUG ROBIN
1 ....... 17620ZH7023.... CAP, FUEL TANK-HONDA
1 ....... 0430430015....... CAP, FUEL TANK-ROBIN
1 ....... 28462ZH8003.... ROPE, RECOIL-HONDA GX160
1 ....... 28462ZE2W11 ... ROPE, RECOIL-HONDA GX240
1 ....... 2703261008....... ROPE, RECOIL-ROBIN EH-25
Part numbers on this Suggested
Spare Parts List may supercede/
replace the P/N's shown in the
test pages of this manual.
NOTE
WC-62P/S CONCRETE MIXER — PARTS & OPERATION MANUAL — REV. #7 (06/30/05) — PAGE 33
Download from Www.Somanuals.com. All Manuals Search And Download.
WC-62P/S CONCRETE MIXER — NAME PLATE AND DECALS
NAME PLATE AND DECALS
PAGE 34 —WC-62P/S CONCRETE MIXERS — PARTS & OPERATION MANUAL — REV. #7 (06/30/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
WC-62P/S CONCRETE MIXER— NAME PLATE AND DECALS
NAME PLATE AND DECALS
NO
PART NO
18252
CIPDCL160
504713
EM948630
DCL151
13118
PART NAME
MQ WHITEMAN LOGO
QTY.
REMARKS
1
*
2
*
3
*
4
*
5
*
6
*
7
3
2
1
1
1
1
DECAL, CRUSHWARNING
DECAL, SAFETY INSTRUCTIONS
DECAL, EMERGENCY STOP
DECAL,TOWING INSTRUCTIONS
DECAL, POWDER COATED
NAMEPLATE........................................................ 1 ......... CONTACT MQ PARTS DEPT.
8
WMDCL6292
DECAL KIT .......................................................... 1 ......... INCLUDES ITEMS W/
*
SEE DECAL ILLUSTRATIONS ON PAGE 11
WC-62P/S CONCRETE MIXER — PARTS & OPERATION MANUAL — REV. #7 (06/30/05) — PAGE 35
Download from Www.Somanuals.com. All Manuals Search And Download.
WC-62P/S — PLASTIC BARREL
PLASTIC BARREL ASSY.
PAGE 36 —WC-62P/S CONCRETE MIXERS — PARTS & OPERATION MANUAL — REV. #7 (06/30/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
WC-62P/S — PLASTIC BARREL
PLASTIC BARREL ASSY.
NO
1
2
3
4
PART NO
510992
EM969013
507532
505390
505469
PART NAME
QTY.
REMARK
RING GEAR
1
3
1
1
1
NUT, LOCK 3/8”NC
BARREL, PLASTIC 6 CU. FT.
PLUG, EXPANSION
KING PIN
5
6
7
8
9
EM903063
EM903026
EM507533
511758
511759
EM963610
492378
SPINDLE BEARING 5/8" CONE ............ 2 ............. REPLACES 492154
SPINDLE BEARING CUP ...................... 2 ............. REPLACES 492233
SUPPORT SPIDER
SHIM PLASTIC #14
SHIM PLASTIC #16
BOLT 3/8" NC 1-1/4" G5
BOLT 3/8" NC 1-3/4" G5
SUPPORT BRACKET, UPPER
WASHER, FLAT
NUT, HEX 3/8" NC
BLADES, PLASTIC
1
AR
AR
3
12
3
15
15
6
10
11
12
13
14
15
16
17
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
507542
3019092
EM969013
507543
507541
507538
508345
490958
502037
492179
EM963692
502036
492584
491008
EM916001
500246
501829
492467
492490
SUPPORT BRACKET, LOWER
SPACER MC8079
CS BOLT, 3/8" NC X 3-1/2" G
RING, RETENTION
3
3
3
2
DRIVE PINION SHAFT
PINION SHAFT BEARING
BOLT 1/2" NC X 1-1/2" G5
HOUSING, JACKSHAFT
LOCKNUT, HEX 1/2" NC
CAP, GREASE FITTING
1
2
2
1
2
3
GREASE FITTING 1/8" NPT ................. 3..............REPLACES 491698
SQUARE KEY
DRIVE PINION
ALLEN SCREW 5/16 NC 3/8"
SET SCREW 1/2" X 1" NC
1
1
1
1
07037-024
EM963102
492584
NUT, HEX LOWER 1-1/2" NF................. 1 ............. REPLACES492579
BOLT 1/2" NC X 1-1/4" NC
LOCKNUT, HEX 1/2" NC
YOKE
1
1
1
507539
WC-62P/S CONCRETE MIXER — PARTS & OPERATION MANUAL — REV. #7 (06/30/05) — PAGE 37
Download from Www.Somanuals.com. All Manuals Search And Download.
WC-62P/S — STEEL BARREL
STEEL BARREL ASSY.
PAGE 38 —WC-62P/S CONCRETE MIXERS — PARTS & OPERATION MANUAL — REV. #7 (06/30/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
WC-62P/S — STEEL BARREL
STEEL BARREL ASSY.
NO
1
2
PART NO
505390
505469
PART NAME
PLUG, EXPANSION
KING PIN
QTY.
1
1
REMARK
3
4
5
6
7
8
8
8
EM903063
EM903026
504095
EM963610
505487
511732
511731
511729
EM969013
490958
502037
492179
EM963692
492584
502036
491008
EM916001
500214
501829
492467
EM505472
492490
EM968306
EM963102
492584
SPINDLE BEARING 5/8" CONE ............ 2 ............. REPLACES 492154
SPINDLE BEARING CUP ...................... 2 ............. REPLACES 492233
RING GEAR
1
6
1
AR
AR
AR
6
BOLT 3/8" NC 1-1/4" G5
BARREL, STEEL 6 CU. FT.
SHIM 0.25 THICK
SHIM .187 THICK
SHIM .140 THICK
9
NUT, LOCK 3/8”NC
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
RING, RETENTION
2
1
2
2
2
1
3
DRIVE PINION SHAFT
PINION SHAFT BEARING
BOLT 1/2" NC X 1-1/2" G5
LOCKNUT, HEX 1/2" NC
HOUSING JACKSHAFT
CAP, GREASE FITTING
GREASE FITTING 1/8" NPT ................. 3.............. REPLACES 491698
SQUARE KEY 1/4" X 30 MM
DRIVE PINION
ALLEN SCREW 5/16 NC 3/8"
SPACER, BARREL
1
1
1
1
1
SET SCREW 1/2" X 1" NC
NUT, HEX LOWER 1-1/2" NF................. 1 ............. REPLACES 492579
BOLT 1/2" NC X 1-1/4" NC
LOCKNUT, HEX 1/2" NC
YOKE
1
1
1
507539
WC-62P/S CONCRETE MIXER — PARTS & OPERATION MANUAL — REV. #7 (06/30/05) — PAGE 39
Download from Www.Somanuals.com. All Manuals Search And Download.
WC-62P/S — MAIN FRAME ASSEMBLY
MAIN FRAME ASSY.
PAGE 40 —WC-62P/S CONCRETE MIXERS — PARTS & OPERATION MANUAL — REV. #7 (06/30/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
WC-62P/S — MAIN FRAME ASSEMBLY
MAIN FRAME ASSY.
NO
1
2
3
4
5
6
7
8
PART NO
501844
2101402
492284
502035
492584
490895
492395
EM916001
491008
EM963055
3109092
0166 A
PART NAME
GUARD, GEAR WHEEL
WASHER, LOCK 1/4"
ROUND HEAD BOLT 1/4" NC 3/8 G2" ......... 4.............. REPLACES 492279
DUMP GEAR
NUT, LOCK 1/2" NC
DUMP LATCH
BOLT 1/2" NC X 1-3/4" G5
GREASE FITTING 1/8" NPT ........................ 2.............. REPLACES 491698
GREASE CAP
BOLT 3/8" NC X 3/4" G5
WASHER, FLAT 3/8"
WASHER, LOCK 3/8"
FRAME
BOLT 1/2"-13 X 4 G5
LOCK NUT 1/2 NC........................................ 1.............. REPLACES 492586
HANDWHEEL SHAFT
HANDWHEEL
SAFETY CHAIN ........................................... 1.............. REPLACES 13363
CONNECTOR LINK
RING RETAINING
CHAIN AND LINK KIT .................................. 1 .............. INCLUDES ITEMS W/
QTY.
1
4
REMARK
1
1
1
1
9
2
3
3
3
1
1
10
11
12
13
14
15
16
17
18
502451
EM124
10176
500167
501905
1
1
*
19
20
21
22
23
24
01004
2
1
*
490961
13363KIT
HBC-1
HLC-1
*
BALL HITCH 2-INCH .................................... 1.............. CONTACT UNIT SALES
LOOP HITCH ................................................ 1.............. CONTACT UNIT SALES
PIN HITCH 1-INCH ....................................... 1.............. CONTACT UNIT SALES
HPC-1
WC-62P/S CONCRETE MIXER — PARTS & OPERATION MANUAL — REV. #7 (06/30/05) — PAGE 41
Download from Www.Somanuals.com. All Manuals Search And Download.
WC-62P/S — AXLE ASSEMBLY
AXLE ASSY.
PAGE 42 —WC-62P/S CONCRETE MIXERS — PARTS & OPERATION MANUAL — REV. #7 (06/30/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
WC-62P/S — AXLE ASSEMBLY
AXLE ASSY.
NO
1
2
3
4
PART NO
PART NAME
QTY.
4
4
2
4
REMARK
492397
BOLT 1/2" NC 1-1/2" G5
LOCK NUT 5/8" NC
SPRING SUPPORT
BOLT 5/8" NC 1-1/2" G5
NUT 1/2" NF
EM969023
501030
492406
5
492589
4
6
7
491928
492584
SPRING LEAF
NUT, HEX 1/2"
2
4
8
8
9
511336
502039
500617
AXLE 1-1/16 SPINDLE
AXLE 7/8" SPINDLE
U-CLAMP
1
1
2
10
#
#
EM941288
EM903049
EM903113
EM903012
3504
OIL SEAL
2
4
4
4
*
11
11
BEARING CONE, (7/8" SPINDLE)
BEARING CONE, (1-1/16" SPINDLE)
BEARING CUP
HUB ASSY., 4-BOLT (7/8" SPINDLE) ............................. 2 ........... INCLUDES ITEMS W/
....................................................................................................... REPLACES 493235
HUB ASSY., 4-BOLT (1-1/16" SPINDLE) ........................ 2 ........... INCLUDES ITEMS W/
WASHER, FLAT, .087" THICKNESS
WASHER, FLAT, .135" THICKNESS
COTTER PIN 1/8" X 1-1/2'
*
#
12
13
*
*
#
13
14
15
16
17
17
18
18
19
20
EM941306
EM511159
501299
491688
12426
8164
3005
493236C
8115
3469
2
AR
2
NUT, SLOTTED HEX JAM (7/8" SPINDLE) .................... 2 ........... REPLACES 3068
NUT, SLOTTED HEX JAM (1-1/16" SPINDLE)
TIRE AND RIM, CARLISE
TIRE AND RIM, UNIROYAL
LUG NUTS
2
2
2
8
2
#
#
*
DUST CAP
*
WC-62P/S CONCRETE MIXER — PARTS & OPERATION MANUAL — REV. #7 (06/30/05) — PAGE 43
Download from Www.Somanuals.com. All Manuals Search And Download.
WC-62P/S — CABINET ASSEMBLY
CABINET ASSY.
PAGE 44 —WC-62P/S CONCRETE MIXERS — PARTS & OPERATION MANUAL — REV. #7 (06/30/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
WC-62P/S — CABINET ASSEMBLY
CABINET ASSY.
NO
1
2
3
4
5
6
7
PART NO
490202
502454
492363
EM923023
13287
PART NAME
QTY.
REMARKS
RUBBER PROTECTOR
CABINET ENGINE ASSY.
BOLT 5/16" NC X 3/4" G5
WASHER, FLAT 5/16"
4
1
4
8
LOCK NUT 8-32 ........................................................6............. REPLACEMENT PART ONLY
WASHER, FLAT #10 .................................................6............. REPLACEMENT PART ONLY
RHMS 8-32 X 1/2".....................................................6............. REPLACEMENT PART ONLY
2203
1307
8
*
9
10
11
491010
EM923343
2105164
EM974007
LATCH ASSY., COMPLETE
WASHER, LOCK 5/16"
NUT 5/16" NC G5
2
4
4
PAINT, SPRAY CAN 12 OZ. TRAFFIC RED
AR
WC-62P/S CONCRETE MIXER — PARTS & OPERATION MANUAL — REV. #7 (06/30/05) — PAGE 45
Download from Www.Somanuals.com. All Manuals Search And Download.
WC-62P/S — GAS ENGINE MOUNTING PLATE ASSEMBLY
GAS ENGINE MOUNTING PLATE ASSY.
PAGE 46 —WC-62P/S CONCRETE MIXERS — PARTS & OPERATION MANUAL — REV. #7 (06/30/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
WC-62P/S — GAS ENGINE MOUNTING PLATE ASSEMBLY
GAS ENGINE MOUNTING PLATE ASSY.
NO
1
1
1
2
3
4
5
6
7
8
9
9
PART NO
GX160K1HX2
GX240K1HA2
EH252YR000
490956
500275
492468
492056
501019
503859
492468
492074
503869
503869
EM923343
EM923023
2105164
502041
PART NAME
QTY.
REMARKS
ENGINE, HONDA 5.5 HP
ENGINE, HONDA 8.0 HP
ENGINE, ROBIN 8.5 HP
RING, RETAINING
1
1
1
1
1
1
1
1
2
1
1
1
SQUARE KEY
SET SCREW 5/16" NC X 3/4"
UPPER PULLEY
SQUARE KEY 3/16" X 45 MM
V-BELT A-38
ALLEN SCREW 5/16" NC X 1/2"
DRIVE PULLEY 5.5 HP HONDA
DRIVE PULLEY 8.0 HP HONDA
DRIVE PULLEY 8.5 HP ROBIN
WASHER, LOCK 5/16"
WASHER, FLAT 5/16"
NUT, HEX 5/16 X18 NC G5
BASE PLATE ENGINE
WASHER, FLAT 1/2"
BOLT, HEX 1/2" NC 1-1/2" G5
BUTTON, STOP
SWITCH, STOP........................................... 1 ........... REPLACES 491845
ENGINE CABLE HARNESS
LOCKNUT 1/2"
BOLT 5/16" X 1-3/4" G5
9
10
11
12
13
14
15
16
17
18
19
20
4
4
4
1
8
4
1
492600
EM963692
29174-001
EM940734
510573
492584
492367
1
4
4
WC-62P/S CONCRETE MIXER — PARTS & OPERATION MANUAL — REV. #7 (06/30/05) — PAGE 47
Download from Www.Somanuals.com. All Manuals Search And Download.
WC-62P/S — ELECTRIC MOTOR MOUNTING PLATE ASSEMBLY
ELECTRIC MOTOR MOUNTING PLATE ASSY.
PAGE 48 —WC-62P/S CONCRETE MIXERS — PARTS & OPERATION MANUAL — REV. #7 (06/30/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
WC-62P/S — ELECTRIC MOTOR MOUNTING PLATE ASSEMBLY
ELECTRIC MOTOR MOUNTING PLATE ASSY.
NO
1
2
PART NO
P145K17DB45A
490956
PART NAME
MOTOR, ELECTRIC 1.5 HP
RING, RETAINING
QTY.
1
1
REMARKS
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
500275
492468
502211
501019
EM900267
492468
502213
EM923343
EM923023
2105164
502041
SQUARE KEY
1
1
1
1
2
1
1
4
4
4
1
8
4
4
4
SET SCREW 5/16" NC X 3/4"
UPPER PULLEY (LARGE)
SQUARE KEY 3/16" X 45 MM
V-BELT A45
ALLEN SCREW 5/16" NC X 1/2"
DRIVE PULLEY (SMALL)
WASHER, LOCK 5/16"
WASHER, FLAT 5/16"
NUT, HEX 5/16 X18 NC G5
BASE PLATE ENGINE
WASHER, FLAT 1/2"
492600
EM963692
4922584
0202
BOLT, HEX 1/2" NC 1-1/2" G5
LOCKNUT 1/2"
BOLT 5/16" X 1" G5
WC-62P/S CONCRETE MIXER — PARTS & OPERATION MANUAL — REV. #7 (06/30/05) — PAGE 49
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1HA2 ENGINE — AIR CLEANER ASSY.
AIR CLEANER ASSY.
PAGE 50 —WC-62P/S CONCRETE MIXERS — PARTS & OPERATION MANUAL — REV. #7 (06/30/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1HA2 ENGINE — AIR CLEANER ASSY.
AIR CLEANER ASSY.
NO.
1
2
3
*
5
PART NO.
PART NAME
QTY.
REMARKS
16271ZE2000
17210ZE2515
17218ZE2505
17231ZH9820
17232891000
17238ZE2310
17239ZE1000
17410ZE2020
0037806000
90325044000
90009ZE2003
9405006000
GASKET, ELBOW ..................................... 1 ............. INCLUDES ITEM W/
*
ELEMENT, AIR CLEANER, DUAL
FILTER, OUTER
COVER, AIR CLEANER
GROMMET, AIR CLEANER
COLLAR, AIR CLEANER
COLLAR B, AIR CLEANER
ELBOW COMP., AIR CLEANER ............... 1 ............. INCLUDES ITEM W/
WINGNUT 6MM
WINGNUT, TOOL BOX SETTING
BOLT- WASHER 6 X 22
NUT, FLANGE 6MM
1
1
1
1
2
1
6
8
9
#
#
10
12
13
14
15
#
1
2
1
2
WC-62P/S CONCRETE MIXER — PARTS & OPERATION MANUAL — REV. #7 (06/30/05) — PAGE 51
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1HA2 ENGINE — CAMSHAFT ASSY.
CAMSHAFT ASSY.
PAGE 52 —WC-62P/S CONCRETE MIXERS — PARTS & OPERATION MANUAL — REV. #7 (06/30/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1HA2 ENGINE — CAMSHAFT ASSY.
CAMSHAFT ASSY.
NO.
1
1
2
3
4
5
6
*
7
8
PART NO.
PART NAME
QTY.
REMARKS
14100ZE2W01
14100ZE2306
14410ZE2013
14431ZE2010
14441ZE2000
14451ZE1013
14568ZE1000
14711ZE2000
14721ZE2000
14751ZE2003
14771ZE2000
14773ZE2000
14781ZE2000
14791ZE2010
90012ZE0010
90206ZE1000
CAMSHAFT ASSY. ................................... 1 ............. INCLUDES ITEM W/
*
CAMSHAFT
ROD PUSH
ARM VALVE ROCKER
LIFTER VALVE
PIVOT ROCKER ARM
SPRING, WEIGHT RETURN
VALVE, IN.
1
2
2
2
2
1
1
1
2
1
1
1
1
2
2
VALVE, EX.
SPRING, VALVE
9
10
11
12
13
14
15
RETAINER, IN. VALVE SPRING
RETAINER, EX. VALVE SPRING
ROTATOR,VALVE
PLATE, PUSH ROD GUIDE
BOLT, PIVOT 8MM
NUT, PIVOT ADJ.
WC-62P/S CONCRETE MIXER — PARTS & OPERATION MANUAL — REV. #7 (06/30/05) — PAGE 53
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1HA2 ENGINE — CARBURETOR ASSY.
CARBURETOR ASSY.
PAGE 54 —WC-62P/S CONCRETE MIXERS — PARTS & OPERATION MANUAL — REV. #7 (06/30/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1HA2 ENGINE — CARBURETOR ASSY.
CARBURETOR ASSY.
NO.
PART NO.
PART NAME
QTY. REMARKS
1 +
16010ZE2812
16011ZA0931
16013ZA0931
16016ZHW01
16024ZE1811
16028ZE0005
16028ZE2005
16100ZE2W71
16124ZE0005
16166ZE2W70
16075GHBB00
16075GHBB00
16211ZE2000
16220ZA0702
16221ZA0800
16223ZA0800
16610ZE1000
16953ZE1812
16954ZE1811
16956ZE1811
16957ZE1812
16967ZE0811
93500030060H
9430520122
GASKET SET
VALVE SET, FLOAT
FLOAT SET
1
1
1
1
1
1
1
*
2
3
*
*
5
SCREW SET
*
6 +
SCREW SET, DRAIN
SCREW SET B
CHOKE SET
CARBURETOR ASSY.................... 1 ..... INCLUDES ITEMS W/
SCREW, THROTTLE STOP
NOZZLE, MAIN
*
7 +
*
8
*
9
*
*
10
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
*
11
*
12
*
COLLAR, SET
O-RING
13
*
14
INSULATOR, CARB.
SPACER COMP., CARB.
GASKET, CARBURETOR
GASKET, INSULATOR
LEVER COMP., CHOKE, STD.
LEVER, VALVE
PLATE, LEVER SETTING
SPRING, VALVE LEVER
GASKET, VALVE
CUP, FUEL STRAINER
SCREW, PAN 3 X 6
PIN, SPRING 2 X 12
JET, MAIN #82, OPTIONAL
JET, MAIN #85, OPTIONAL
JET, MAIN #88
15
16
17
18
19
*
20
*
21
*
22
*
23
*
24
*
25
26
99101ZH70820
99101ZH70850
99101ZH80880
99204ZE20400
16015ZE8005
*
26
*
26
*
27
28
JET SET, PILOT #40
CHAMBER SET, FLOAT ................ 1 ..... INCLUDES ITEMS W/+
*
*
WC-62P/S CONCRETE MIXER — PARTS & OPERATION MANUAL — REV. #7 (06/30/05) — PAGE 55
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1HA2 ENGINE — CONTROL ASSY.
CONTROL ASSY.
PAGE 56 —WC-62P/S CONCRETE MIXERS — PARTS & OPERATION MANUAL — REV. #7 (06/30/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1HA2 ENGINE — CONTROL ASSY.
CONTROL ASSY.
NO.
2
3
4
5
PART NO.
PART NAME
ARM, GOVERNOR
ROD, GOVERNOR
SPRING, GOVERNOR
SPRING,THROTTLE RETURN
CONTROL ASSEMBLY ................................ 1 .......... INCLUDES ITEMS W/
QTY.
REMARKS
16551ZE2000
16555ZE2000
16561ZE2000
16571ZE2000
16570ZE2W00
16571ZE2W00
16574ZE1000
16575ZE2W00
16578ZE1000
16581ZE2W00
16584883300
90013883000
90015ZE5010
90114SA0000
93500050280A
9405006000
1
1
1
1
8
*
10
LEVER, CONTROL
SPRING, LEVER
1
1
1
1
1
1
2
1
1
1
1
*
11
*
12
*
WASHER, CONTROL LEVER
SPACER, CONTROL LEVER
BASE, CONTROL
SPRING, CONTROL ADJUSTING
BOLT, FLANGE (6 X 12) (CT200)
BOLT, GOVERNOR ARM
NUT, SELF- LOCK (6MM)
SCREW, PAN (5 X 28)
NUT, FLANGE
14
*
15
*
16
*
19
20
21
*
24
*
27
WC-62P/S CONCRETE MIXER — PARTS & OPERATION MANUAL — REV. #7 (06/30/05) — PAGE 57
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1HA2 ENGINE — CRANKCASE COVER ASSY.
CRANKCASE COVER ASSY.
PAGE 58 —WC-62P/S CONCRETE MIXERS — PARTS & OPERATION MANUAL — REV. #7 (06/30/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1HA2 ENGINE — CRANKCASE COVER ASSY.
CRANKCASE COVER ASSY.
NO.
2
PART NO.
11400ZE2621
PART NAME
QTY.
REMARKS
COVER ASSY., CRANKCASE ..................... 1........... INCLUDES ITEMS W/
(H-TYPE) (BALANCER)
*
3
4
5
8
9
11381ZE2801
15600ZG4003
15600735003
15625ZE1003
15625ZE1003
16510ZE2811
GASKET, CASE COVER
1
CAP ASSY., OIL FILLER ............................. 1........... INCLUDES ITEMS W/
CAP ASSY., OIL FILLER ............................. 1........... INCLUDES ITEMS W/
#
%
%
#
GASKET, OIL FILLER CAP
GASKET, OIL FILLER CAP
1
1
10
GOVERNOR ASSEMBLY (BALANCER) ...... 1........... INCLUDES ITEMS W/+
11 + 16511ZE2000
WEIGHT, GOVERNOR
2
1
2
1
1
1
2
1
7
1
1
1
1
*
12 + 16512ZE2811
HOLDER, GOVERNORWEIGHT
PIN, GOVERNOR WEIGHT
SLIDER, GOVERNOR
WASHER (6 X 16)
CLIP, GOVERNOR HOLDER
PIN, DOWEL (8 X 12)
WASHER, PLAIN (6MM)
BOLT, FLANGE (8 X 35)
BEARING, RADIAL BALL (6202)
BEARING, RADIAL BALL (6204)
BEARING, RADIAL BALL (6206)
BEARING, RADIAL BALL (6302)
*
13 + 16513ZE2000
*
14
15
16
17
18
19
20
21
22
23
16531ZE2000
90473147000
90602ZE1000
90701HC4000
58176
957010803500
961006202000
961006204000
961006206000
961006302000
*
*
*
*
*
*
*
*
WC-62P/S CONCRETE MIXER — PARTS & OPERATION MANUAL — REV. #7 (06/30/05) — PAGE 59
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1HA2ENGINE — CRANKSHAFT ASSY.
CRANKSHAFT ASSY.
PAGE 60 —WC-62P/S CONCRETE MIXERS — PARTS & OPERATION MANUAL — REV. #7 (06/30/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1HA2ENGINE — CRANKSHAFT ASSY.
CRANKSHAFT ASSY.
NO.
3
8
PART NO.
PART NAME
QTY.
REMARKS
13320ZE2611
13351ZE2010
961006206000
CRANKSHAFT (L- TYPE)............................. 1 .......... INCLUDES ITEM W/
*
WEIGHT BALANCER
BEARING, RADIAL BALL (6206)
1
1
12
*
WC-62P/S CONCRETE MIXER — PARTS & OPERATION MANUAL — REV. #7 (06/30/05) — PAGE 61
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1HA2 ENGINE — CYLINDER BARREL ASSY.
CYLINDER BARREL ASSY.
PAGE 62 —WC-62P/S CONCRETE MIXERS — PARTS & OPERATION MANUAL — REV. #7 (06/30/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1HA2 ENGINE — CYLINDER BARREL ASSY.
CYLINDER BARREL ASSY.
NO.
1
2
3
6
7
8
*
9
10
11
12
13
PART NO.
PART NAME
QTY.
REMARKS
12000ZE2834
15510ZE2043
16541ZE2010
90131896650
90446KE1000
91201890003
91353671003
9405010000
031112230
CYLINDER ASSY., BALANCER + OIL ALERT ...... 1 .......... INCLUDES ITEMS W/
*
SWITCH ASSY., OIL LEVEL
SHAFT, GOVERNOR ARM
BOLT, DRAIN PLUG
WASHER 8.2 X17X0.8
OIL SEAL 30X46X8
O-RING 14MM ARAI
NUT FLANGE 10MM
WASHER, DRAIN PLUG 12MM
PIN, LOCK 10MM
BOLT, FLANGE 6X12
BEARING, RADIAL BALL 6202
BOLT, FLANGE 6X12 CT200
ALERT UNIT, OIL
1
1
2
1
1
1
1
2
1
2
1
1
1
9425110000
957010601200
961006202000
90013883000
34150ZH7003
14
15
16
*
WC-62P/S CONCRETE MIXER — PARTS & OPERATION MANUAL — REV. #7 (06/30/05) — PAGE 63
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1HA2 ENGINE — CYLINDER HEAD ASSY.
CYLINDER HEAD ASSY.
PAGE 64 —WC-62P/S CONCRETE MIXERS — PARTS & OPERATION MANUAL — REV. #7 (06/30/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1HA2 ENGINE — CYLINDER HEAD ASSY.
CYLINDER HEAD ASSY.
NO.
PART NO.
PART NAME
QTY.
REMARKS
1
12200ZH9000
12204ZE2306
12205ZE2305
12216ZE2300
12251ZE2800
12310ZE2020
12391ZE2020
14775ZE2010
90014ZE2000
90042ZE2000
92900080320E
90441ZE2010
9430112200
CYLINDER HEAD COMP. ....................................... 1 .......... INCLUDES ITEMS W/
*
2
*
3
*
4
*
5
6
7
GUIDE, VALVE, OS, OPTIONAL
GUIDE, EX. VALVE, OS, OPTIONAL
CLIP, VALVE GUIDE
GASKET, CYLINDER HEAD
COVER COMP., HEAD
GASKET, CYLINDER HEAD COVER
SEAT, VALVE SPRING
BOLT, HEAD COVER
BOLT, STUD 8X123
BOLT, STUD 8X47
WASHER COMP., HEAD COVER
PIN A, DOWEL 12X20
BULK HOSE, VACUUM 11X1000, 11X100
BOLT, FLANGE 10X80
1
1
1
1
1
1
1
1
2
2
1
2
1
4
1
1
8
10
11
12
13
14
15
16
17
17
950051100130M
957011008000
9807956846
SPARK PLUG, BPR6ES, NGK
SPARK PLUG, W20EPR-U, DENSO
9807956855
WC-62P/S CONCRETE MIXER — PARTS & OPERATION MANUAL — REV. #7 (06/30/05) — PAGE 65
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1HA2 ENGINE — FAN COVER ASSY.
FAN COVER ASSY.
PAGE 66 —WC-62P/S CONCRETE MIXERS — PARTS & OPERATION MANUAL — REV. #7 (06/30/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1HA2 ENGINE — FAN COVER ASSY.
FAN COVER ASSY.
NO.
1
2
3
4
5
7
9
PART NO.
PART NAME
QTY.
REMARKS
16731ZE2003
19610ZE2010ZC
19631ZE2D00
32197ZH8003
36100ZE1015
90013883000
90684ZA0601
CLIP, TUBE
1
1
1
1
1
6
1
COVER COMP., FAN *NH1* BLACK
SHROUD
SUB-HARNESS
SWITCH ASSY., ENGINE STOP
BOLT, FLANGE 6X12, CT200
CLIP, WIRE HARNESS
WC-62P/S CONCRETE MIXER — PARTS & OPERATION MANUAL — REV. #7 (06/30/05) — PAGE 67
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1HA2 ENGINE — FLYWHEEL ASSY.
FLYWHEEL ASSY.
PAGE 68 —WC-62P/S CONCRETE MIXERS — PARTS & OPERATION MANUAL — REV. #7 (06/30/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1HA2 ENGINE — FLYWHEEL ASSY.
FLYWHEEL ASSY.
NO.
1
2
4
7
PART NO.
PART NAME
QTY.
REMARKS
19511ZE2000
28450ZE2W11
31100ZE2010
90201ZE3V00
90741ZE2000
FAN, COOLING
1
1
1
1
1
PULLEY COMP., STARTER, SCREEN GRID
FLYWHEEL COMP.
NUT, SPECIAL 16MM
8
KEY, SPECIAL WOODRUFF 25X18
WC-62P/S CONCRETE MIXER — PARTS & OPERATION MANUAL — REV. #7 (06/30/05) — PAGE 69
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1HA2 ENGINE — MUFFLER ASSY.
MUFFLER ASSY.
PAGE 70 —WC-62P/S CONCRETE MIXERS — PARTS & OPERATION MANUAL — REV. #7 (06/30/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1HA2 ENGINE — MUFFLER ASSY.
MUFFLER ASSY.
NO.
1
2
3
4
5
6
7
8
PART NO.
PART NAME
QTY.
1
1
1
1
1
1
1
1
1
1
6
3
1
5
REMARKS
18310ZE2W00
18320ZE2W01
18323ZE2W00
18330ZE2W00
18331ZE2810
18333ZK6Y00
18355ZE2010
18381ZE2W10
18381ZE2800
90013883000
90050ZE1000
90055ZE1000
90050ZE1000
9405008000
MUFFLER
PROTECTOR, MUFFLER
PROTECTOR, EX. PIPE
PIPE, EX.
CAP, MUFFLER
GASKET, EX. PIPE
ARRESTER, SPARK
GASKET, MUFFLER (ARRESTER)
GASKET, MUFFLER
BOLT, FLANGE (6 X 12) (CT200)
SCREW, TAPPING (5 X 8)
SCREW, TAPPING (4 X 6)
SCREW, TAPPING (5 X 8) (OPTIONAL)
NUT, FLANGE (8MM)
9
10
11
12
13
14
WC-62P/S CONCRETE MIXER — PARTS & OPERATION MANUAL — REV. #7 (06/30/05) — PAGE 71
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1HA2 ENGINE — FUELTANK ASSY.
FUEL TANK ASSY.
PAGE 72 —WC-62P/S CONCRETE MIXERS — PARTS & OPERATION MANUAL — REV. #7 (06/30/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1HA2 ENGINE — FUELTANK ASSY.
FUEL TANK ASSY.
NO.
1
2
3
5
6
*
8
11
12
13
14
15
PART NO.
PART NAME
RUBBER SUPPORTER 107MM
JOINT, FUEL TANK
TANK COMP., FUEL *NH1*, BLACK
CAP COMP., FUEL FILLER .................................... 1 .......... INCLUDES ITEMS W/
GASKET, FUEL FILLER CAP
FILTER, FUEL
O-RING 14MM, ARAI
NUT, FLANGE 8MM
BULK HOSE, FUEL 4.5X3000, 4.5X222
CLIP, TUBE, B8
BOLT, FLANGE 8X25
QTY.
REMARKS
16854ZH8000
16955ZE1000
17510ZE2010ZD
17620ZH7023
17631ZH7003
17672ZE2W01
91353671003
9405008000
1
1
1
*
1
1
1
2
1
2
2
950014500360M
9500202080
957010802500
WC-62P/S CONCRETE MIXER — PARTS & OPERATION MANUAL — REV. #7 (06/30/05) — PAGE 73
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1HA2ENGINE — IGNITION ASSY.
IGNITION COIL ASSY.
PAGE 74 —WC-62P/S CONCRETE MIXERS — PARTS & OPERATION MANUAL — REV. #7 (06/30/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1HA2ENGINE — IGNITION ASSY.
IGNITION COIL ASSY.
NO.
1
2
6
8
PART NO.
PART NAME
QTY.
REMARKS
30500ZF6W02
30700ZE1013
31512ZE2000
36101ZE1010
90015883000
COIL ASSY., IGNITION
CAP ASSY., NOISE SUPPRESSOR
GROMMET, WIRE
1
1
1
1
2
WIRE, STOP SWITCH 370MM
BOLT, FLANGE 6X28
11
WC-62P/S CONCRETE MIXER — PARTS & OPERATION MANUAL — REV. #7 (06/30/05) — PAGE 75
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1HA2 ENGINE — PISTON ASSY.
PISTON ASSY.
PAGE 76 —WC-62P/S CONCRETE MIXERS — PARTS & OPERATION MANUAL — REV. #7 (06/30/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1HA2 ENGINE — PISTON ASSY.
PISTON ASSY.
NO.
1
1
1
1
2
2
2
2
3
4
4
5
*
6
PART NO.
PART NAME
QTY.
REMARKS
13010ZE2013
13011ZE2013
13012ZE2013
13013ZE2013
13101ZE2W00
13102ZE2W00
13103ZE2W00
13104ZE2W00
13111ZE2000
13200ZE2000
13200ZE2305
90001ZE8000
90551ZE1000
RING SET, PISTON, STD.
RING SET, PISTON, OS 0.25, OPTIONAL
RING SET, PISTON, OS 0.50, OPTIONAL
RING SET, PISTON, 0.75, OPTIONAL
PISTON, STANDARD
1
1
1
1
1
1
1
1
1
PISTON, OS 0.25, OPTIONAL
PISTON, OS 0.50, OPTIONAL
PISTON, 0.75, OPTIONAL
PIN, PISTON
ROD ASSY., CONNECTING STANDARD ................ 1 .......... INCLUDES ITEMS W/
ROD ASSY., CONNECTING, US 0.25, OPT.
BOLT, CONNECTING ROD
*
1
2
2
CLIP, PISTON PIN 18MM
WC-62P/S CONCRETE MIXER — PARTS & OPERATION MANUAL — REV. #7 (06/30/05) — PAGE 77
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1HA2 ENGINE — RECOIL STARTER ASSY.
RECOIL STARTER ASSY.
PAGE 78 —WC-62P/S CONCRETE MIXERS — PARTS & OPERATION MANUAL — REV. #7 (06/30/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1HA2 ENGINE — RECOIL STARTER ASSY.
RECOIL STARTER ASSY.
NO.
PART NO.
PART NAME
QTY.
REMARKS
1
28400ZE2W01ZB
28410ZE2W01ZB
28421ZE2W01
28422ZE2W01
28441ZE2W01
28442ZE2W01
28443ZE2W01
28444ZE2W01
28461ZE2W02
28462ZE2W11
90004ZE2W01
90008ZE2003
STARTER ASSY., RECOIL *NH1*, BLK ............... 1 ......... INCLUDES ITEMS W/
*
2
3
CASE COMP., RECOIL STARTER *NH1*, BLK
PULLEY, RECOIL STARTER
RATCHET, STARTER
SPRING, FRICTION
SPRING, STARTER RETURN
SPRING RATCHET
RETAINER, SPRING
GRIP, STARTER
ROPE, RECOIL STARTER
SCREW, CENTER
BOLT, FLANGE 6X10
1
1
2
1
1
2
1
1
1
1
3
*
*
4
5
*
*
6
7
*
*
8
*
10
*
11
*
13
*
14
WC-62P/S CONCRETE MIXER — PARTS & OPERATION MANUAL — REV. #7 (06/30/05) — PAGE 79
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1HA2 ENGINE — GEAR REDUCTION ASSY.
GEAR REDUCTION ASSY.
PAGE 80 —WC-62P/S CONCRETE MIXERS — PARTS & OPERATION MANUAL — REV. #7 (06/30/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1HA2 ENGINE — GEAR REDUCTION ASSY.
GEAR REDUCTION ASSY.
NO.
1
2
3
4
5
6
7
8
PART NO.
PART NAME
QTY.
REMARKS
11500ZE2620
11521ZE2800
22103ZE2620
23220ZE2621
23710ZE2621
90401ZE2620
90402ZE2620
90473842000
90745ZE2600
91201890003
9430108140
COVER ASSY, REDUCTION CASE ............. 1 .......... INCLUDES ITEMS W/
*
GASKET, CHAIN CASE COVER
GEAR, PRIMARY DRIVE (17T)
COUNTERSHAFT
SHAFT, P.T.O. (H- TYPE)
SHIM A (OPTIONAL)
SHIM B (OPTIONAL)
WASHER (8MM)
1
1
1
1
AR
AR
1
1
1
2
1
6
1
9
KEY (6.3 X 6.3 X 43)
10
11
12
13
OIL SEAL (30 X 46 X 8)
PIN A, DOWEL ( 8 X 14)
BOLT, FLANGE (8 X 25)
BOLT, FLANGE (8 X 40)
BEARING, RADIAL BALL (6206)
BEARING, RADIAL BALL (6302)
*
957010802500
957010804000
961006206000
961006302000
14
15
*
*
1
WC-62P/S CONCRETE MIXER — PARTS & OPERATION MANUAL — REV. #7 (06/30/05) — PAGE 81
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1HA2 ENGINE — LABEL ASSY.
LABEL ASSY.
PAGE 82 —WC-62P/S CONCRETE MIXERS — PARTS & OPERATION MANUAL — REV. #7 (06/30/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1HA2 ENGINE — LABEL ASSY.
LABELS ASSY.
NO.
1
2
3
5
15
16
PART NO.
PART NAME
QTY.
REMARKS
87521ZE2W01
87522ZE1810
87522ZH9000
87528ZE2810
87586ZH7W00
87532ZH8810
EMBLEM, INTERNAL
MARK, CAUTION, EXTERNAL
LABEL, CAUTION
1
1
1
1
1
1
MARK, CHOKE, EXTERNAL
LABEL, FUEL CAUTION
MARK, OIL ALERT
WC-62P/S CONCRETE MIXER — PARTS & OPERATION MANUAL — REV. #7 (06/30/05) — PAGE 83
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1HX2 — AIR CLEANER ASSY.
AIR CLEANER ASSY.
PAGE 84 —WC-62P/S CONCRETE MIXERS — PARTS & OPERATION MANUAL — REV. #7 (06/30/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1HX2 — AIR CLEANER ASSY.
AIR CLEANER ASSY.
NO.
1
2
3
*
4
PART NO.
PART NAME
QTY.
REMARKS
16271ZE1000
17210ZE1517
17218ZE1505
17230ZE1820
17232891000
17238ZE7010
17239ZE1000
17410ZE1020
9405006000
GASKET, ELBOW
1
ELEMENT, AIR CLEANER (DUAL) ......... 1 ................ INCLUDES ITEMS W/
FILTER, OUTER
*
1
1
1
2
1
COVER, AIR CLEANER (DUAL)
GROMMET, AIR CLEANER
COLLAR, AIR CLEANER
COLLAR B, AIR CLEANER
ELBOW, AIR CLEANER ......................... 1 ................ INCLUDES ITEMS W/
NUT, CAP 6MM
WINGNUT, TOOL BOX SETTING ........... 1 ................ USE FROM ENGINE SN 2836834
WINGNUT, TOOL BOX SETTING
BOLT, FLANGE 6 X 20 ........................... 1 ................ USE FROM ENGINE SN 3385102
5
*
6
7
8
9
#
#
#
2
11
12
13
90325044000
90325044000
957010602000
1
WC-62P/S CONCRETE MIXER — PARTS & OPERATION MANUAL — REV. #7 (06/30/05) — PAGE 85
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1HX2 — CAMSHAFT ASSY.
CAMSHAFT ASSY.
PAGE 86 —WC-62P/S CONCRETE MIXERS — PARTS & OPERATION MANUAL — REV. #7 (06/30/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1HX2 — CAMSHAFT ASSY.
CAMSHAFT ASSY.
NO.
1
2
3
4
PART NO.
PART NAME
QTY.
REMARKS
14100ZE1812
14410ZE1010
14431ZE1000
14441ZE1010
14451ZE1013
14568ZE1000
14711ZF1000
14721ZF1000
14751ZF1000
14771ZE1000
14773ZE1000
14781ZE1000
14791ZE1010
90012ZE0010
90206ZE1000
CAMSHAFT ASSEMBLY ..................................... 1 ........... INCLUDES ITEMS W/
*
ROD, PUSH
ARM, VALVE ROCKER
LIFTER, VALVE
PIVOT, ROCKER ARM
SPRING, WEIGHT RETURN
VALVE, INTAKE
VALVE, EXHAUST
SPRING VALVE
RETAINER, INTAKE VALVE SPRING
RETAINER, EXHAUST VALVE SPRING
ROTATOR,VALVE
PLATE, PUSH ROD GUIDE
BOLT, PIVOT 8MM
2
2
2
2
1
1
1
2
1
1
1
1
2
2
5
6
*
7
8
9
10
11
12
13
14
15
NUT, PIVOT ADJ.
WC-62P/S CONCRETE MIXER — PARTS & OPERATION MANUAL — REV. #7 (06/30/05) — PAGE 87
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1HX2 — CARBURETOR ASSY.
CARBURETOR ASSY.
PAGE 88 —WC-62P/S CONCRETE MIXERS — PARTS & OPERATION MANUAL — REV. #7 (06/30/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1HX2 — CARBURETOR ASSY.
HONDA GX160K1HX2 — CARBURETOR ASSY.
CARBURETOR ASSY.
NO.
PART NO.
PART NAME
QTY.
REMARKS
■
+%
1
2
3
#
16010ZE1812
16011ZE0005
16013ZE0005
16015ZE0831
GASKET SET
VALVE SET, FLOAT
FLOAT SET
1
1
1
*
*
4
CHAMBER SET, FLOAT............................... 1 ........... INCLUDES ITEMS/#
.................................................................................... USE FROM ENGINE
.................................................................................... SN BE65B B
*
5
16016ZH7W01
16024ZE1811
16028ZE0005
16044ZE0005
16100ZH8W51
16124ZE0005
16166ZH8W50
16173001004
16211ZE1000
16212ZH8800
16220ZE1020
16221ZH8801
16610ZE1000
16953ZE1812
16954ZE1812
SCREW SET
SCREW SET, DRAIN ................................... 1 ........... INCLUDES ITEM W/+
SCREW SET B ............................................ 1 ........... INCLUDES ITEM W/
CHOKE SET
CARBURETOR ASSEMBLY, BE65B B ........ 1 ........... INCLUDES ITEMS/
1
*
6
7
8
#
*
%
*
1
*
9
*
10
11
12
13
14
15
16
17
18
19
SCREW, THROTTLE STOP
NOZZLE, MAIN
O- RING
INSULATOR, CARBURETOR
GASKET, INSULATOR
SPACER, CARBURETOR
GASKET, CARBURETOR
1
1
1
1
1
1
1
*
*
*
LEVER, CHOKE STANDARD ....................... 1............ INCLUDES ITEM W/$
LEVER, VALVE
1
*
PLATE, LEVER SETTING............................ 1 ........... USE FROM ENGINE
.................................................................................... SN BE65B B
20
21
22
23
16956ZE1811
16957ZE1812
16967ZE0811
93500030060H
SPRING, VALVE LEVER
GASKET, VALVE
CUP, FUEL STRAINER
SCREW, PAN 3 X 6 ...................................... 2 ........... USE FROM ENGINE
.................................................................................... SN BE65B B
PIN, SPRING 2 X 12
JET, MAIN #65 (OPTIONAL)
JET, MAIN #68 (OPTIONAL)
JET SET, PILOT #35 .................................... 1 ........... INCLUDES ITEM W/
1
1
1
*
*
*
*
24$
9430520122
1
1
1
25
99101ZH80650
99101ZH80680
99204ZE00350
*
25
*
■
26
*
WC-62P/S CONCRETE MIXER — PARTS & OPERATION MANUAL — REV. #7 (06/30/05) — PAGE 89
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1HX2 — CONTROL ASSY.
CONTROL ASSY.
PAGE 90 —WC-62P/S CONCRETE MIXERS — PARTS & OPERATION MANUAL — REV. #7 (06/30/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1HX2 — CONTROL ASSY.
CONTROL ASSY.
NO.
2
4
5
6
PART NO.
PART NAME
QTY.
REMARKS
16500ZH8823
16551ZL0000
16555ZE1000
16561ZE1020
16562ZE1020
16571ZH8020
16574ZE1000
16575ZH8000
16576891000
16578ZE1000
16580ZH8812
16584883300
16592ZE1810
90013883000
90016ZE5010
90114SA0000
93500050250H
938930501600
9405006000
CONTROL ASSEMBLY, REMOTE......................... 1............ INCLUDES ITEMS W/
*
ARM, GOVERNOR
ROD, GOVERNOR
SPRING GOVERNOR
SPRING,THROTTLE RETURN
LEVER, CONTROL
SPRING, LEVR
WASHER, CONTROL LEVER
HOLDER, CABLE
SPACER, CONTROL LEVER
BASE, CONTROL (REMOTE)
SPRING, CONTROL ADJUSTING
SPRING, CABLE RETURN
BOLT, FLANGE 6 X 12 (CT200)
BOLT, GOVERNOR ARM
NUT, SELF- LOCK 6MM
SCREW, PAN 5 X 25
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
7
8
9
*
*
10
*
11
*
12
*
13
*
14
*
15
*
17
18
19
*
22
*
23
*
SCREW, WASHER 5 X 16
NUT, FLANGE 6MM
24
WC-62P/S CONCRETE MIXER — PARTS & OPERATION MANUAL — REV. #7 (06/30/05) — PAGE 91
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1HX2 — CRANKCASE COVER ASSY.
CRANKCASE COVER ASSY.
PAGE 92 —WC-62P/S CONCRETE MIXERS — PARTS & OPERATION MANUAL — REV. #7 (06/30/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1HX2 — CRANKCASE COVER ASSY.
CRANKCASE COVER ASSY.
NO.
1
3
4
5
PART NO.
PART NAME
QTY.
REMARKS
11300ZE1641
11381ZH8801
15600ZE1003
15600ZG4003
COVER ASSEMBLY, CRANKCASE (U- TYPE) ......1 ............INCLUDES ITEMS W/
*
GASKET, CASE COVER (NON- ASBESTOS)
CAP ASSEMBLY, OIL FILLER ...............................1 ............INCLUDES ITEMS W/
CAP ASSEMBLY, OIL FILLER ...............................1 ............INCLUDES ITEMS W/
1
#
%
10%# 15625ZE1003
GASKET, OIL FILLER CAP
OIL SEAL 25 X 41 X 6
PIN A, DOWEL 8 X 14
BOLT, FLANGE 8 X 32
BEARING, RADIAL BALL 6205
1
1
2
6
1
11
12
13
14
91202883005
9430108140
957010803200
961006205010
*
*
WC-62P/S CONCRETE MIXER — PARTS & OPERATION MANUAL — REV. #7 (06/30/05) — PAGE 93
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1HX2 — CRANKSHAFT ASSY.
CRANKSHAFT ASSY.
PAGE 94 —WC-62P/S CONCRETE MIXERS — PARTS & OPERATION MANUAL — REV. #7 (06/30/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1HX2 — CRANKSHAFT ASSY.
CRANKSHAFT ASSY.
NO.
3
PART NO.
13310ZE1622
PART NAME
CRANKSHAFT, Q- TYPE
QTY.
1
REMARKS
WC-62P/S CONCRETE MIXER — PARTS & OPERATION MANUAL — REV. #7 (06/30/05) — PAGE 95
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1HX2 — CYLINDER BARREL ASSY.
CYLINDER BARREL ASSY.
PAGE 96 —WC-62P/S CONCRETE MIXERS — PARTS & OPERATION MANUAL — REV. #7 (06/30/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1HX2 — CYLINDER BARREL ASSY.
CYLINDER BARREL ASSY.
NO.
2
3
PART NO.
PART NAME
QTY.
REMARKS
12000ZH8811
15510ze1033
16510ZE1000
16511ZE1000
16512ZE1000
16531ZE1000
16541ZE1000
90131ZE1000
80451ZE1000
90601ZE1000
90602ZE1000
91001ZF1003
91202883005
91353671003
9405010000
CYLINDER ASSEMBLY, OIL ALERT .................... 1............ INCLUDES ITEMS W/
SWITCH ASSEMBLY, OIL LEVEL
*
#
4
GOVERNOR ASSEMBLY ...................................... 1............ INCLUDES ITEMS W/
WEIGHT, GOVERNOR
HOLDER, GOVERNOR WEIGHT
SLIDER, GOVERNOR
SHAFT, GOVERNOR ARM
BOLT, DRAIN PLUG
WASHER, THRUST 6MM
WASHER, DRAIN PLUG 10.2MM
CLIP, GOVERNOR HOLDER
BEARING, RADIAL BALL 6205
OIL SEAL 25 X 41 X 6
O- RING 13.5 X 1.5 (ARAI)
NUT, FLANGE 10MM
WASHER, PLAIN 6MM
PIN, LOCK 8MM
BOLT, FLANGE 6 X 12
5
6
8
9
#
#
2
1
1
1
2
1
2
1
1
1
1
1
2
1
2
10
11
12
13
14
15
16
17
18
19
20
*
*
9410106800
9425108000
957010601200
WC-62P/S CONCRETE MIXER — PARTS & OPERATION MANUAL — REV. #7 (06/30/05) — PAGE 97
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1HX2 — CYLINDER HEAD ASSY.
CYLINDER HEAD ASSY.
PAGE 98 —WC-62P/S CONCRETE MIXERS — PARTS & OPERATION MANUAL — REV. #7 (06/30/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1HX2 — CYLINDER HEAD ASSY.
CYLINDER HEAD ASSY.
NO.
PART NO.
PART NAME
QTY.
REMARKS
1
12210ZH8000
12204ZE1306
12205ZE1315
12216ZE5300
12251ZF1800
12310ZE1020
12391ZE1000
15721ZH8000
90016ZE1000
90043ZE1020
90047ZE1000
9430110160
CYLINDER HEAD.................................................. 1............ INCLUDES ITEMS W/
*
2
*
3
*
GUIDE, VALVE OS (OPTIONAL
GUIDE, EXHAUST VALVE OS (OPTIONAL) ......... 1............ INCLUDES ITEM W/
CLIP, VALVE GUIDE
GASKET, CYLINDER HEAD
COVER, HEAD
GASKET, CYLINDER HEAD COVER
TUBE, BREATHER
BOLT, FLANGE 6 X13
BOLT, STUD 6 X109
1
%
4
5
6
7
8
9
%
1
1
1
1
1
4
2
2
2
4
1
*
10
11
12
14
15
BOLT, STUD 8 X 32
PIN A, DOWEL 10 X16
BOLT, FLANGE 8 X60
SPARK PLUG BPR6ES (NGK)
957230806000
9807956846
WC-62P/S CONCRETE MIXER — PARTS & OPERATION MANUAL — REV. #7 (06/30/05) — PAGE 99
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1HX2 — FAN COVER ASSY.
FAN COVER ASSY.
PAGE 100 —WC-62P/S CONCRETE MIXERS — PARTS & OPERATION MANUAL — REV. #7 (06/30/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1HX2 — FAN COVER ASSY.
FAN COVER ASSY.
NO.
2
4
7
8
10
11
13
14
17
19
PART NO.
PART NAME
QTY.
REMARKS
19610ZE1000ZC
19611ZH8810
90601ZH7013
19630ZH8000
32197ZH8003
36100ZE1015
90013883000
90022888010
34150ZH7003
957010600800
COVER, FAN "NH1" (BLACK)
PLATE, SIDE (OIL ALERT)
CLIP, HARNESS
1
1
1
1
1
1
6
1
1
1
SHROUD
SUB- HARNESS
SWITCH ASSEMBLY, ENGINE STOP
BOLT, FLANGE 6 X12 (CT200)
BOLT, FLANGE 6 X20 (CT200)
ALERT UNIT, OIL
BOLT, FLANGE 6 X8
WC-62P/S CONCRETE MIXER — PARTS & OPERATION MANUAL — REV. #7 (06/30/05) — PAGE 101
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1HX2 — FLYWHEEL ASSY.
FLYWHEEL ASSY.
PAGE 102 —WC-62P/S CONCRETE MIXERS — PARTS & OPERATION MANUAL — REV. #7 (06/30/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1HX2 — FLYWHEEL ASSY.
FLYWHEEL ASSY.
NO.
1
2
4
5
5
8
PART NO.
PART NAME
KEY, SPECIAL WOODRUFF (25 X18)
FAN, COOLING
PULLEY, STARTER
FLYWHEEL
FLYWHEEL, LAMP
NUT, SPECIAL 14MM
QTY.
REMARKS
13331357000
19511ZE1000
28451ZH8003
31100ZE1010
31100ZE1810
90201878003
1
1
1
1
1
1
WC-62P/S CONCRETE MIXER — PARTS & OPERATION MANUAL — REV. #7 (06/30/05) — PAGE 103
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1HX2 — FUELTANK ASSY.
FUEL TANK ASSY.
PAGE 104 —WC-62P/S CONCRETE MIXERS — PARTS & OPERATION MANUAL — REV. #7 (06/30/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1HX2 — FUELTANK ASSY.
FUEL TANK ASSY.
NO.
1
2
3
3
PART NO.
PART NAME
RUBBER, SUPPORTER 107MM
JOINT, FUEL TANK
TANK, FUEL *R8* (BRIGHT RED)
TANK, FUEL *NH1* (BLACK)
CAP, FUEL FILLER ............................................... 1 ........... INCLUDES ITEM W/
GASKET, FUEL FILLER CAP
O- RING 13.5 X1.5 (ARAI)
NUT, FLANGE 6MM
BULK HOSE, FUEL 4.5 X 3000 (4.5 X 140)
CLIP, TUBE B8
QTY.
REMARKS
16854ZH8000
16955ZE1000
17510ZE1020ZB
17510ZE1020ZF
17620ZH7023
17631ZH7003
91353671003
9405006000
1
1
1
1
5
6
*
1
1
2
1
2
1
*
11
12
13
14
15
950014500360M
9500202080
957010602500
BOLT, FLANGE 6 X 25
WC-62P/S CONCRETE MIXER — PARTS & OPERATION MANUAL — REV. #7 (06/30/05) — PAGE 105
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1HX2 — IGNITION COIL ASSY.
IGNITION COIL ASSY.
PAGE 106 —WC-62P/S CONCRETE MIXERS — PARTS & OPERATION MANUAL — REV. #7 (06/30/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1HX2 — IGNITION COIL ASSY.
IGNITION COIL ASSY.
NO.
1
2
7
11
PART NO.
PART NAME
QTY.
REMARKS
30500ZE1043
30700ZE1013
36101ZE1010
957010602500
COIL ASSEMBLY, IGNITION
CAP ASSEMBLY, NOISE SUPPRESSOR
WIRE, STOP SWITCH 370MM
BOLT, FLANGE 6 X25
1
1
1
2
WC-62P/S CONCRETE MIXER — PARTS & OPERATION MANUAL — REV. #7 (06/30/05) — PAGE 107
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1HX2 — MUFFLER ASSY.
MUFFLER ASSY.
PAGE 108 —WC-62P/S CONCRETE MIXERS — PARTS & OPERATION MANUAL — REV. #7 (06/30/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1HX2 — MUFFLER ASSY.
MUFFLER ASSY.
NO.
1
1
3
7
PART NO.
PART NAME
QTY.
REMARKS
18310ZF1000
18310ZH8810
18320ZF1H01
18355ZE1000
18381ZH8800
90050ZE1000
90055ZE1000
020108060
MUFFLER
1
1
1
1
1
4
1
2
MUFFLER (OPTIONAL)
PROTECTOR, MUFFLER
ARRESTER, SPARK (OPTIONAL)
GASKET, MUFFLER
SCREW, TAPPING 5 X 8 (OPTIONAL
SCREW, TAPPING 4 X 6 (OPTIONAL)
NUT, HEX. 8MM
8
11
12
15
WC-62P/S CONCRETE MIXER — PARTS & OPERATION MANUAL — REV. #7 (06/30/05) — PAGE 109
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1HX2 — PISTON ASSY.
PISTON ASSY.
PAGE 110 —WC-62P/S CONCRETE MIXERS — PARTS & OPERATION MANUAL — REV. #7 (06/30/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1HX2 — PISTON ASSY.
PISTON ASSY.
NO.
1
1
1
1
1
1
1
1
2
2
2
2
3
4
4
5
PART NO.
PART NAME
QTY.
REMARKS
13010ZF1023
13010ZH8941
13011ZF1023
13011ZH8941
13012ZF1023
13012ZH8941
13013ZF1023
13013ZH8941
13101ZH8010
13102ZH8000
13101ZH8010
13104ZH8000
13111ZE1000
132A0ZE1000
13200ZE1010
90001ZE1000
90551ZE1000
RING SET, PISTON (STANDARD) ............................ 1 ........ USE UP TO ENG S/N 5495899
RING SET, PISTON (STANDARD) ............................ 1 ........ USE FROM ENG S/N 5495900
RING SET, PISTON (OS 0.25) ................................. 1 ........ USE UP TO ENG S/N 5495899
RING SET, PISTON (OS 0.25), OPTIONAL ............. 1 ........ USE FROM ENG S/N 5495900
RING SET, PISTON (OS 0.50), OPTIONAL ............. 1 ........ USE UP TO ENG S/N 5495899
RING SET, PISTON (OS 0.50), OPTIONAL ............. 1 ........ USE FROM ENG S/N 5495900
RING SET, PISTON (0.75), OPTIONAL ................... 1 ........ USE UP TO ENG S/N 5495899
RING SET, PISTON (0.75), OPTIONAL ................... 1 ........ USE FROM ENG S/N 5495900
PISTON (STANDARD)
1
1
1
1
1
1
1
2
2
PISTON (OS 0.25), OPTIONAL
PISTON (OS 0.50), OPTIONAL
PISTON (0.75), OPTIONAL
PIN, PISTON
ROD ASSY., CONNECTING (US 0.25), OPT.
ROD ASSEMBLY, CONNECTING
BOLT, CONNECTING ROD
CLIP, PISTON PIN 18MM
6
WC-62P/S CONCRETE MIXER — PARTS & OPERATION MANUAL — REV. #7 (06/30/05) — PAGE 111
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1HX2 — RECOIL STARTER ASSY.
RECOIL STARTER ASSY.
PAGE 112 —WC-62P/S CONCRETE MIXERS — PARTS & OPERATION MANUAL — REV. #7 (06/30/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1HX2 — RECOIL STARTER ASSY.
RECOIL STARTER ASSY.
NO.
PART NO.
PART NAME
QTY.
REMARKS
1
28400ZH8013ZB
28410ZH8003ZB
28420ZH8013
28422ZH8013
28433ZH8003
28441ZH8003
28442ZH8003
28443ZH8003
28461ZH8003
28462ZH8003
90003ZH8003
90008ZE2003
STARTER ASSY., RECOIL "NH1" BLACK ...................1 ............INCLUDES ITEM W/
*
2
CASE, RECOIL STARTER "NH1" BLACK
REEL, RECOIL STARTER
RATCHET, STARTER
GUIDE, RATCHET
SPRING, FRICTION
SPRING, RECOIL STARTER
SPRING, RETURN
KNOB, RECOIL STARTER
ROPE, RECOIL STARTER
SCREW, SETTING
1
1
2
1
1
1
2
1
1
1
3
*
3
*
4
*
5
*
6
*
7
*
8
*
9
*
10
*
11
*
12
BOLT, FLANGE 6 X10
WC-62P/S CONCRETE MIXER — PARTS & OPERATION MANUAL — REV. #7 (06/30/05) — PAGE 113
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1HX2 — GEAR REDUCTION ASSY.
1/6 GEAR REDUCTION ASSY.
PAGE 114 —WC-62P/S CONCRETE MIXERS — PARTS & OPERATION MANUAL — REV. #7 (06/30/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1HX2 — GEAR REDUCTION ASSY.
1/6 GEAR REDUCTION ASSY.
NO.
1
2
3
4
5
6
7
7
8
9
10
11
12
13
PART NO.
PART NAME
QTY.
1
REMARKS
21521883741
21591ZH8740
21621883741
21692ZH8800
23710883740
90002883740
90131883000
90131896650
91202883005
9410912000
CASE REDUCTION
GASKET, REDUCTION CASE
COVER, REDUCTION
GASKET, REDUCTION COVER
SHAFT, PTO
BOLT, BREATHING
BOLT, DRAIN
1
1
1
1
1
1
1
1
1
4
4
1
BOLT, DRAIN
OIL SEAL 25 X41 X 6
WASHER, DRAIN PLUG 12MM
BOLT, FLANGE 8X32
BOLT, FLANGE 8X35
BEARING, RADIAL BALL 6204
BEARING, RADIAL BALL 6305
957010803208
957010803500
961006204000
961006305000
1
WC-62P/S CONCRETE MIXER — PARTS & OPERATION MANUAL — REV. #7 (06/30/05) — PAGE 115
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1HX2 — ENGINE LABELS ASSY.
ENGINE LABELS ASSY.
PAGE 116 —WC-62P/S CONCRETE MIXERS — PARTS & OPERATION MANUAL — REV. #7 (06/30/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1HX2 — ENGINE LABELS ASSY.
ENGINE LABELS ASSY.
NO.
1
3
6
7
8
15
PART NO.
PART NAME
QTY.
REMARKS
87521ZH8020
87522ZH9000
87528ZE1810
87530ZH8810
87532ZH8810
887586ZH7W00
ENBLEM 5.5
1
1
1
1
1
1
LABEL, CAUTION
MARK, CHOKE
LABEL, SPECIFICATION (EXTERNAL)
MARK, OIL ALERT (E)
LABEL, FUEL CAUTION
WC-62P/S CONCRETE MIXER — PARTS & OPERATION MANUAL — REV. #7 (06/30/05) — PAGE 117
Download from Www.Somanuals.com. All Manuals Search And Download.
Effective: October 1, 2002
TERMS AND CONDITIONS OF SALE — PARTS
PAYMENT TERMS
5. Partsmustbeinnewandresalablecon- Multiquipreservestherighttoquoteandsell
dition,intheoriginalMultiquippackage(if directtoGovernmentagencies,andtoOriginal
any), and with Multiquip part numbers Equipment Manufacturer accounts who use
Terms of payment for parts are net 10 days.
FREIGHTPOLICY
clearlymarked.
our products as integral parts of their own
products.
All parts orders will be shipped collect or
prepaidwiththechargesaddedtotheinvoice.
All shipments are F.O.B. point of origin.
Multiquip’sresponsibilityceaseswhenasigned
manifesthasbeenobtainedfromthecarrier,
andanyclaimforshortageordamagemustbe
settledbetweentheconsigneeandthecarrier.
6. Thefollowingitemsarenotreturnable:
SPECIALEXPEDITINGSERVICE
a. Obsolete parts. (If an item is in the
price book and shows as being re- A$35.00surchargewillbeaddedtotheinvoice
placedbyanotheritem,itisobsolete.) forspecialhandlingincludingbusshipments,
insuredparcelpostorincaseswhereMultiquip
mustpersonallydeliverthepartstothecarrier.
(such as gaskets, seals, “O” rings,
b. Any parts with a limited shelf life
andotherrubberparts)thatwerepur- LIMITATIONSOFSELLER’SLIABILITY
MINIMUMORDER
chasedmorethansixmonthspriorto
thereturndate.
Multiquip shall not be liable hereunder for
damagesinexcessofthepurchasepriceofthe
The minimum charge for orders from Mul-
tiquipis$15.00net.Customerswillbeasked
for instructions regarding handling of orders
notmeetingthisrequirement.
c. Anylineitemwithanextendeddealer item with respect to which damages are
netpriceoflessthan$5.00.
claimed, and in no event shall Multiquip be
liable for loss of profit or good will or for any
otherspecial,consequentialorincidentaldam-
ages.
d. Special order items.
RETURNEDGOODSPOLICY
e. Electricalcomponents.
f. Paint,chemicals,andlubricants.
g. Decalsandpaperproducts.
h. Itemspurchasedinkits.
Returnshipmentswillbeacceptedandcredit
willbeallowed,subjecttothefollowingprovi-
sions:
LIMITATIONOFWARRANTIES
Nowarranties,expressorimplied,aremade
in connection with the sale of parts or trade
accessoriesnorastoanyenginenotmanufac-
tured by Multiquip. Such warranties made in
connectionwiththesaleofnew,completeunits
are made exclusively by a statement of war-
rantypackagedwithsuchunits,andMultiquip
neitherassumesnorauthorizesanypersonto
assume for it any other obligation or liability
whatever in connection with the sale of its
products.Apartfromsuchwrittenstatementof
warranty, there are no warranties, express,
impliedorstatutory,whichextendbeyondthe
descriptionoftheproductsonthefacehereof.
1. AReturnedMaterialAuthorizationmust
be approved by Multiquip prior to ship-
ment.
7. Thesenderwillbenotifiedofanymaterial
receivedthatisnotacceptable.
2. ToobtainaReturnMaterialAuthorization,
alistmustbeprovidedtoMultiquipParts
Salesthatdefinesitemnumbers,quanti-
ties, and descriptions of the items to be
returned.
8. Suchmaterialwillbeheldforfiveworking
days from notification, pending instruc-
tions.Ifareplyisnotreceivedwithinfive
days,thematerialwillbereturnedtothe
senderathisexpense.
a. Thepartsnumbersanddescriptions
must match the current parts price
list.
9. Creditonreturnedpartswillbeissuedat
dealer net price at time of the original
purchase,lessa15%restockingcharge.
b. The list must be typed or computer
generated.
10. In cases where an item is accepted, for
which the original purchase document
can not be determined, the price will be
basedonthelistpricethatwaseffective
twelvemonthspriortotheRMAdate.
c. The list must state the reason(s) for
thereturn.
d. The list must reference the sales
order(s)orinvoice(s)underwhichthe
itemswereoriginallypurchased.
11. Credit issued will be applied to future
purchasesonly.
e. The list must include the name and
phonenumberofthepersonrequest-
ingtheRMA.
PRICINGANDREBATES
Prices are subject to change without prior
notice.Pricechangesareeffectiveonaspe-
cificdateandallordersreceivedonorafterthat
datewillbebilledattherevisedprice.Rebates
3. AcopyoftheReturnMaterialAuthoriza-
tionmustaccompanythereturnshipment.
4. Freight is at the sender’s expense. All forpricedeclinesandaddedchargesforprice
partsmustbereturnedfreightprepaidto increaseswillnotbemadeforstockonhand
Multiquip’sdesignatedreceivingpoint.
atthetimeofanypricechange.
PAGE 118 —WC-62P/S CONCRETE MIXERS — PARTS & OPERATION MANUAL — REV. #7 (06/30/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE PAGE
WC-62P/S CONCRETE MIXER — PARTS & OPERATION MANUAL — REV. #7 (06/30/05) — PAGE 119
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION AND PARTS MANUAL
HERE'S HOW TO GET HELP
PLEASE HAVE THE MODEL AND SERIAL
NUMBER ON-HAND WHEN CALLING
MULTIQUIP’SMAINPHONENUMBERS
800-421-1244
310-537-3700
FAX: 310-537-3927
PARTSDEPARTMENT
800-427-1244
310-537-3700
FAX: 800-672-7877
FAX: 310-637-3284
MAYCOPARTS
800-306-2926
310-537-3700
FAX: 800-672-7877
FAX: 310-637-3284
SERVICEDEPARTMENT
800-478-1244
310-537-3700
FAX: 310-537-4259
MQPOWERSERVICEDEPARTMENT
800-835-2551
310-537-3700
FAX: 310-638-8046
TECHNICALASSISTANCE
800-478-1244
FAX: 310-631-5032
WARRANTYDEPARTMENT
800-421-1244, EXT. 279 FAX: 310-537-1173
310-537-3700, EXT. 279
MULTIQUIP INC.
POST OFFICE BOX 6254
CARSON, CA 90749
310-537-3700 • 800-421-1244
FAX:310-537-3927
WWW:multiquip.com
Atlanta • Boise • Dallas • Houston • Newark
Quebec, Canada • Manchester, UK • Rio De Janiero, BR • Guadalajara, MX
Download from Www.Somanuals.com. All Manuals Search And Download.
|