PARTS AND OPERATION MANUAL
MULTIQUIP
Model GA-9.7 HZ
A.C. GENERATOR
Revision #2 (03/05/01)
MULTIQUIPINC.
PARTS DEPARTMENT:
18910 WILMINGTON AVE.
800-427-1244
CARSON, CALIFORNIA 90746 FAX: 800-672-7877
310-537-3700
800-421-1244
SERVICE DEPARTMENT/TECHNICAL ASSISTANCE:
800-478-1244
FAX:310-537-3927
FAX:310-631-5032
Atlanta • Boise • Dallas • Houston • Newark
Montreal, Canada • Manchester, UK
Rio De Janiero, Brazil • Guadalajara, Mexico
Download from Www.Somanuals.com. All Manuals Search And Download.
PAGE 2 — GA-9.7 HZ A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (03/05/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
HERE'S HOW TO GET HELP
PLEASE HAVE THE MODEL AND SERIAL NUMBER
ON-HAND WHEN CALLING
PARTS DEPARTMENT
800-427-1244 or 310-537-3700
FAX: 800-672-7877 or 310-637-3284
SERVICE DEPARTMENT/TECHNICAL ASSISTANCE
800-478-1244 or 310-537-3700
FAX: 310- 537-4259
WARRANTY DEPARTMENT
888-661-4279, or 310-661-4279
FAX: 310- 537-1173
MAIN
800-421-1244 or 310-537-3700
FAX: 310-537-3927
GA-9.7 HZ A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (03/05/01) — PAGE 3
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
Here's How To Get Help ............................................ 3
Table Of Contents ..................................................... 4
Parts Ordering Procedures ....................................... 5
Rules For Safe Operation ......................................... 6
Operation and Safety Decals .................................... 7
Specifications ............................................................ 8
General Information .................................................. 9
Honda GX610 K1 Engine
Cylinder Head Assembly....................................34-35
Cylinder Barrel Assembly...................................36-37
Crankcase Cover Assembly...............................38-39
Crankshaft Assembly .........................................40-41
Piston Assembly.................................................42-43
Camshaft Assembly ...........................................44-45
Recoil Starter Assembly.....................................46-47
Fan Cover Assembly ..........................................48-49
Carburetor Assembly .........................................50-51
Air Cleaner Assembly.........................................52-53
Muffler Assembly ...............................................54-55
Fuel Pump Assembly .........................................56-57
Flywheel Assembly ............................................58-59
Ignition Coil Assembly ........................................60-61
Starter Motor Assembly .....................................62-63
Governor Control Assembly...............................64-65
Labels ................................................................66-67
Gasket Kit................................................................ 68
Multiquip GA-9.7 HZ —
AC Generator
Controls and Indicators ........................................... 10
Installation ............................................................... 11
Pre-Setup ........................................................... 12-13
Instrumentation ....................................................... 14
Load Application ..................................................... 15
Operating Instructions............................................. 16
Maintenance ........................................................... 17
Preparation For Long Term Storage ....................... 18
Wiring Diagram ....................................................... 19
Troubleshooting (Engine)................................... 20-21
Troubleshooting (Generator) ............................. 22-23
Explanation Of Codes In Remarks Column ............ 24
Suggested Spare Parts ........................................... 25
Generator Assembly .......................................... 26-27
Control Box Assembly ........................................ 28-29
Pipe Frame Assembly ........................................ 30-31
Nameplate And Decals ...................................... 32-33
Terms and Conditions Of Sale — Parts .................. 69
NOTE
Specification and part number
are subject to change without
notice.
PAGE 4 — GA-9.7 HZ A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (03/05/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS ORDERING PROCEDURES
Dealer account number
Dealer name and address
Shipping address (if different than billing address)
Return fax number
Applicable model number
Quantity, part number and description of each part
Specify preferred method of shipment:
UPS Ground
•
UPS Second Day or Third Day*
•
UPS Next Day*
•
Federal Express Priority One (please provide us with your Federal
Express account number)*
•
Airborne Express*
•
Truck or parcel post
•
*Normally shipped the same day the order is received, if prior to 2PM west coast time.
Earn Extra Discounts when
you order by FAX!
All parts orders which include complete part numbers
and are received by fax qualify for the following extra
discounts:
Number of
line items ordered
Additional Discount
1-9 items
3%
10+ items**
5%
Get special freight allowances
when you order 10 or more
line items via FAX!**
Now! Direct TOLL-FREE access
to our Parts Department!
UPS Ground Service at no charge for freight
PS Third Day Service at one-half of actual freight cost
No other allowances on freight shipped by any other carrier.
Toll-free nationwide:
800-421-1244
**Common nuts, bolts and washers (all items under $1.00 list price)
do not count towards the 10+ line items.
Toll-free FAX:
*DISCOUNTS ARE SUBJECT TO CHANGE*
800/6-PARTS-7 • 800-672-7877
Fax order discount and UPS special programs revised June 1, 1995
GA-9.7 HZ A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (03/05/01) — PAGE 5
Download from Www.Somanuals.com. All Manuals Search And Download.
RULES FOR SAFE OPERATION
I
Provide adequate ventilation when operating the generator.
DO NOT operate the generator in any enclosed or narrow
space. The generator's gasoline engine gives off DEADLY
carbon monoxide gas.
CAUTION:
Failure to follow instructions in this manual
may lead to serious injury or even death!This
equipment is to be operated by trained and
qualified personnel only! This equipment is
for industrial use only.
I
I
I
I
NEVER operate the generator in an explosive atmosphere or
near combustible materials. An explosion or fire could result
causing severe bodily harm or even death.
The following safety guidelines should always be used when
operating the GA-9.7 HZ Generator:
Always make sure that the generator is secure on level ground
so that it cannot slide or shift around, endangering workers.
Also keep the immediate area free of bystanders.
GENERAL SAFETY
I
I
I
DO NOT operate or service this equipment before reading
When using a concrete vibrator or a similar device that is
immersed in a water based solution, make sure the device is
equipped with short circuit protection.
this entire manual.
This equipment should not be operated by persons under 18
years of age.
Always use rubber boots and gloves when operating a
concrete vibrator or similar device.
NEVER operate this equipment without proper protective
clothing, shatterproof glasses, steel-toed boots and other
protective devices required by the job.
I
I
Use adequate size connecting cable for extension.
I
This generator is a source of potentially LETHAL high voltage.
Never permit unqualified personnel-especially children to
operate the generator.
Maintain electrical cords in good condition and frequently
replace the entire cable of the concrete vibrator with a new
one.
I
I
Always refuel in a well-ventilated area, away from sparks and
open flames.
I
HighTemperatures – Allow the machine and engine to cool
before adding fuel or performing service and maintenance
functions. Contact with hot components can cause serious
burns.
Always use extreme caution when working with flammable
liquids. When refueling, stop the engine and allow it to cool.
DO NOT smoke around or near the machine. Fire or explosion
could result from fuel vapors, or if fuel is spilled on a hot
engine.
Emergencies
I
Always know the location of the nearest fire extinguisher
and first aid kit. Know the location of the nearest telephone.
Also know the phone numbers of the nearest ambulance,
doctor and fire department. This information will be
invaluable in the case of an emergency.
I
I
This generator is equipped with a ground terminal for your
protection. Always complete the grounding path from the
generator to an external grounding source.
NEVER operate this generator, or handle any electrical
equipment while standing in water, while bare foot, while
hands are wet, or in the rain. Electrical shock could occur
causing severe bodily harm or even death.
Maintenance Safety
I
NEVER lubricate components or attempt service on a running
machine.
I
Always allow the machine a proper amount of time to cool
before servicing.
I
I
Keep electrical cords in good condition. Worn, bare or frayed
wiring can cause electrical shock, leading to bodily harm or
even death.
I
I
Keep the machinery in proper running condition.
Fix damage to the machine immediately and always replace
broken parts.
This generator requires an adequate free flow of cooling air.
Never operate the generator in any enclosed or narrow area
where free flow of the air is restricted. If the air flow is restricted
it will cause serious damage to the generator and may cause
injury to people.
I
I
I
Dispose of hazardous waste properly.Examples of potentially
hazardous waste are used motor oil, fuel and fuel filters.
DO NOT use food or plastic containers to dispose of
hazardous waste.
I
NEVER touch the hot exhaust manifold, muffler or cylinder.
Allow these parts to cool before servicing generator.
DO NOT pour waste, oil or fuel directly onto the ground,
down a drain or into any water source
PAGE 6 — GA-9.7 HZ A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (03/05/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION AND SAFETY DECALS
Machine Safety Decals
The GA-9.7 HZ portable generator is equipped with a number of safety decals.These decals are provided for operator safety and
maintenance information.The illustration below shows these decals as they appear on the machine. Should any of these decals
become unreadable, replacements can be obtained from your dealer.
GA-9.7 HZ A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (03/05/01) — PAGE 7
Download from Www.Somanuals.com. All Manuals Search And Download.
GA-9.7 HZ — SPECIFICATIONS
Table 1. Specifications
MODEL
GA-9.7 HZ
Type
2-pole, Brushless Type Revolving Field
Max. Output
9700 Watts
8400 Watts
Rated Output (continuous)
Rated Voltage
Rated Current
Phase
120/240 V
20.0/30.0 A
60 Cycle Generator
Single Phase (3-wire)
60 Hz
Frequency
Rated Speed
Power Factor
Max Current (Main Breaker)
Model
3600 RPM
100%
2-pole 35 Amps
Honda GX610K1VD
Air-cooled 4 stroke OVH 90 V- Twin
horizontal shaft gasoline engine
Type
Bore X Stroke
Displacement
3.03 in X 2.60 in
18.8 cc
Rated Output
18.0 H.P./3600 R.P.M.
Approx. 10 U.S. Gallons
Unleaded Automobile Gasoline
3 1/16 pints
Engine
Fuel Tank Capacity
Fuel
Lube Oil Capacity
Speed Control Method
Starting Method
Centrifugal Fly-weight Type
Electric/Recoil Start
800 X 540 X 700 mm
344 lbs (156 Kg.)
Dimension (LXWXH)
Dry Net Weight
Effects of Altitude and Heat
The maximum output of the engine listed above is applicable to supplying electrical power for continuous service at ambient
conditions in accordance with SAE Test cord J607. The above ambient conditions are at standard sea level, with a barometric
reading of 29.92 inches and a temperature of 60 degrees fahrenheit.
Generally, the engine output power will decrease 3 1/2% for each 1000 feet of altitude above sea level, and 1% for each 10° F
fahrenheit above the standard temperature of 60° F
PAGE 8 — GA-9.7 HZ A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (03/05/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
GA-9.7 HZ — GENERAL INFORMATION
Excitation System
WARNING:
All GA-series generators use a magnet attached to a flywheel
to produce AC voltage from a lamp coil beneath the flywheel.
As the magnet passes the coil it produces approximately
19-22 AC volts.
Before connecting this generator to
any building’s electrical system, a
licensed electrician must install an
isolation (transfer) switch.
This voltage (19-22 VAC) is then sent to the control box that
contains three rectifying diodes:
Serious injury or death may result
without this transfer switch.
l
l
l
Excitation (diode 1)
Battery (diode 2)
Slow Down (diode 3)
GA-9.7 HZ FAMILIARIZATION
Generator
The AC voltage will pass through the excitation diode that
converts the voltage to DC power.
The Multiquip Model GA-9.7 HZ generator has been designed
as a portable lightweight power source for 60 Hz (single-
phase) vibrators, lighting facilities, power tools, submersible
pumps and other industrial and construction machinery.
This DC power is then sent to the excitation windings housed
within the main windings commonly called the "stator".
This generator is powered by a HONDA gasoline engine.
The alternator, a brushless revolving-field type, is
permanently aligned to the engine through rigid coupling.
This voltage is then transferred into the rotor through
induction.The rotor contains two diodes within it which rectify
the DC voltage and send it out through the main windings,
as AC voltage.
The generator is mounted on rubber vibration isolators that
have a steel base backplate which is attached to the
protective steel pipe carrying frame.The protective carrying
frame is made of steel tubing and fully wraps around the
generator to protect against damage.
Engine
The four-cycle air-cooled HONDA gasoline engine is designed
to meet every performance requirement of this generator.
Reference Table 1, page 8 for engine specifications.
This portable generator is supplied with a electrical control
box. To reduce vibration caused by the engine, the control
box is also placed on rubber isolators.
Figure 1 (page 10) shows the basic controls and indicators
for the GA-9.7 HZ generator.
Control Box
The control box is provided with the following:
NOTE
l
l
l
l
l
l
l
l
Three 120/240V output receptacles (single phase).
Two 120 V output GFI receptacles (single phase).,
Five circuit breakers, one for each receptacle.
One 240 V, 60 Hz main circuit breaker.
AC Voltmeter.
In keeping with Multiquip's policy of
constantly improving its products, the
specifications quoted herein are subject
to change without prior notice.
Idle Control Switch.
Full Power Switch.
Operation Switch.
GA-9.7 HZ A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (03/05/01) — PAGE 9
Download from Www.Somanuals.com. All Manuals Search And Download.
GA-9.7 HZ — CONTROLS AND INDICATORS
Figure 1. Controls and Indicators
PAGE 10 — GA-9.7 HZ A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (03/05/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
GA-9.7 HZ — INSTALLATION
Outdoor Installation
Indoor Installation
Install the generator in a location where it will not be exposed to
rain or sunshine. Make sure that the generator is on secure level
ground so that it cannot slide or shift around. Also install the
generator in a manner so that the exhaust will not be discharged
in the direction of nearby homes.
Exhaust gases from gasoline engines are extremely
poisonous. Whenever an engine is installed indoors the
exhaust fumes must be vented to the outside. The engine
should be installed at least two feet from any outside wall.
Using an exhaust pipe which is too long or too small can
cause excessive back pressure which will cause the engine
to heat excessively and possibly burn the valves.
The installation site must be relatively free from moisture and
dust. All electrical equipment should be protected from excessive
moisture.Failure to do will result in deterioration of the insulation
and will result in short circuits and grounding.
Eliminate the danger of deadly carbon monoxide gas.
Remember that exhaust fumes from any gasoline engine
are very poisonous if discharged in a closed room, but
harmless if allowed to mix with the outside air.If the generator
is installed indoors, you must make provisions for venting
the engine exhaust to the outside of the building.
Foreign materials such as dust, sand, lint and abrasive materials
have a tendency to cause excessive wear, not only to the engine
parts, but also to the alternator parts.
CAUTION :
CAUTION :
Preventing electrical shock. Pay close
attention to handling when operating
concrete vibrators. Always use rubber
boots and gloves to insulate the body from
a short circuit.
Pay close attention to ventilation when
operating the generator inside confined
areas. The engine exhaust contains
noxious elements.
GA-9.7 HZ A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (03/05/01) — PAGE 11
Download from Www.Somanuals.com. All Manuals Search And Download.
GA-9.7 HZ — PRE-SETUP
General Inspection Prior to Operation
Circuit Breaker
This generator has been thoroughly inspected prior to To protect the generator from an overload, circuit breakers are
shipment from the factory. However, be sure to check for provided for single (60 Hz) phase on the control box. Make
damaged parts or components, or loose nuts and bolts, which sure to switch the circuit breakers to the "OFF" position
could have occurred in transit.
prior to starting the engine.
Ground
Extension Cable
When electric power is to be provided to various tools or loads at
some distance from the generator, extension cords are normally
used. Cables should be sized to allow for distance in length and
amperage so that the voltage drop between the generator and
point of use (load) is held to a minimum. Use the cable selection
chart (Table 2 ) as a guide for selecting proper cable size.
The nut and ground terminal on the generator should always
be used to connect the generator to a suitable ground. The
ground path should be of #8 size wire.
Connect the terminal of the ground wire between the lock
washer and the nut and tighten the nut fully. Connect their
end of the wire to a suitable ground.
Ground the Generator
Ground the generator from its ground connector so that
resistance to ground is 500 ohms or less.
Ground the Tool
Ground the tool (load) in the same manner as the generator.
Table 2. Cable Selection (60 Hz, single phase operation)
Load In Watts
At 120 At 240
Maximum Allowable Cable Length
Current
in
Amperes
#10 Wire
#12 Wire
#14 Wire
#16 Wire
Volts
Volts
2.5
5
300
600
1000 ft.
500 ft.
350 ft.
250 ft.
150 ft.
125 ft.
75 ft.
600 ft.
300 ft.
200 ft.
150 ft.
100 ft.
75 ft.
375 ft.
200 ft.
125 ft.
100 ft.
65 ft.
250 ft.
125 ft.
100 ft.
600
1200
1800
2400
3600
4800
7200
7.5
10
15
20
30
900
1200
1800
2400
3600
50 ft.
50 ft.
35 ft.
CAUTION: Equipment damage can result from low voltage.
PAGE 12 — GA-9.7 HZ A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (03/05/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
GA-9.7 HZ — PRE-SETUP
Fuel
Lubrication Oil
Fill the fuel tank with clean and fresh unleaded gasoline. Do
not fill the tank beyond capacity.
Fill the engine crankcase with lubricating oil through the filler
hole, but do not overfill. Make sure the generator is level.
With the dipstick inserted all the way, but without being
screwed into the filler hole, verify that the oil level is
maintained between the two notches on the dipstick.
Pay attention to the fuel tank capacity when replenishing
fuel. Refer to the fuel tank capacity listed on page 8
Specification Table1.
The oil listed in Table 3 is recommended to ensure better
engine performance. Use class SC or higher grade motor
oil.
The fuel tank cap must be closed tightly after filling.
Handle fuel in a safety container. If the container does not have
a spout, use a funnel.
NOTE
CAUTION :
This HONDA engine is equipped with a low oil
shutdown capability. A built in sensor will
automatically turn off the engine should the oil level
fall below a safe operating condition. Make sure
the generator is placed on level ground. Placing
the generator on level ground will ensure that the
low oil sensor will function properly.
Never fill the fuel tank while the engine is
running or in the dark. Gasoline spillage
on a hot engine can cause a fire or
explosion. If gasoline spillage occurs, wipe
up the spilled gasoline completely to
prevent fire hazards.
Table 3. Recommended Motor Oil
Temperature
Type Oil
Range
104° F ~ 23° F
SAE 30
(40° C ~ -5°C)
23° F ~ 5° F
SAE 20 or sae 10W-30
(-5° C ~ -15°C)
Below 5° C (-15°) SAE 10W or SAE 10W-30
GA-9.7 HZ A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (03/05/01) — PAGE 13
Download from Www.Somanuals.com. All Manuals Search And Download.
GA-9.7 HZ — INSTRUMENTATION
Idle Control Switch
CAUTION :
This unit is provided with an automatic idle control for noise
suppression and reduced fuel consumption.The automatic
idle control automatically engages under a no-load condition.
With the automatic idle control switched “ON”, the engine
revolutions will automatically drop to about 2500 rpm (low-
speed operation) within 3 seconds after the load stops.When
the operation is resumed, the engine speed is automatically
increased to about 3600 rpm (high-speed operation) as soon
as the load is connected.
When using a combination of dual
receptacles, total load should not exceed
the rated capacity of the generating.
Power Outlets
The generator has the following 60 Hz 120/240 volt single-
phase receptacles.
l
Single Phase
Fuel Gauge
Two Duplex NEMA (GFCI) 5-20R (120V, 20 Amp)
One Twist Lock NEMA L5-30R (120V, 30 Amp)
One Twist Lock NEMA L6-20R (240V, 20 Amp)
One Twist Lock NEMA L5-30R (120/240, 30 Amp)
The fuel gauge is located on the fuel tank and allows easy
monitoring of the fuel level.
ACVoltmeter
This voltmeter indicates (with a mark) the rated 60 Hz,
single phase output voltage. In addition the voltmeter can
also be used as a diagnostic tool.
Main Circuit Breaker (2-Pole 60 Hz)
If the voltmeter indicator (needle) is below the rated voltage,
engine problems may exist (low/high RPM's). To prevent
damage to the generator or power tools turn the generator
OFF and consult your authorized Multiquip service dealer.
This 2-pole 35 amp breaker protects the generator from short
circuiting or overloading from the 60 Hz single phase load.
PAGE 14 — GA-9.7 HZ A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (03/05/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
GA-9.7 HZ — LOAD APPLICATION
Single Phase Load
CAUTION:
Motors and motor-driven equipment draw
much greater current for starting than
during operation.
Always be sure to check the nameplate on the generator
and equipment to insure the wattage, amperage and
frequency requirements are satisfactorily supplied by the
generator for operating the equipment.
Generally, the wattage listed on the nameplate of the
equipment is its rated output. Equipment may require 130—
150% more wattage than the rating on the nameplate, as
the wattage is influenced by the efficiency, power factor and
starting system of the equipment.
An inadequate size connecting cable which cannot carry
the required load can cause a voltage drop which can burn
out the appliance or tool and overheat the cable.
The idle control is operated at minimum load capacity of
100W. If the load capacity is less than 100W, throw the idle
control switch to the OFF position.
NOTE
If wattage is not given on the equipment's
name plate, approximate wattage may be
determined by multiplying nameplate
voltage by the nameplate amperage.
WATTS = VOLTAGE x AMPERAGE
To determine the running wattage for your load, multiply the
running wattage as indicated by steps 1, 2, and 3 below:
1. INCANDESCENT LOADS
Lights, heaters and similar appliances.
Total the running wattage and multiply by 1.
Example:
29 light bulbs @ 100W each = 2.9 KW
use a 3 KW generator.
2. SMALL MOTORS
Drills and other small power tools.
Total the running wattage and multiply by 2.
Example:
A 1 inch drill runs at 1 KW
use a 2 KW generator.
3. LARGE MOTORS
Submersible pumps, table saws etc.
Total the running wattage and multiply by 3.
Example:
A conveyor belt runs at 8 KW
use a 24 KW generator.
GA-9.7 HZ A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (03/05/01) — PAGE 15
Download from Www.Somanuals.com. All Manuals Search And Download.
GA-9.7 HZ — OPERATING INSTRUCTIONS
Warm up
Before Starting
1. When the engine starts, open the choke slowly.
1. Be sure to disconnect the electrical load and switch the
main circuit breaker to the “OFF”position prior to starting
the engine.
2. Run the engine at low speed for 3 minutes without load
until the engine warms up.
2. Never start the engine with the main circuit breaker “ON”.
3. Turn the idle control switch to the "OFF" (down) position
and check the voltage by referring to the voltmeter on
the control box.
3. Check the lubricating oil level prior to starting the engine.
Make sure the generator is level. The oil level must be
maintained between two notches on the dipstick.
CAUTION:
4. When there is not enough lubricating oil, fill the crankcase
with high grade motor oil. Use a high quality detergent
oil classified SC, SD or SE. (See Table 3 on page 13)
DO NOT change the engine speed control
lever which has been set at the factory prior
to shipping.
CAUTION:
1. Check the generator for abnormal noise and smells.Then
connect the load to the receptacles of the generator.
l
NEVER start the engine when the oil level
is below the lower mark on the dipstick.
2. Switch the main circuit breaker to the “ON” position and
turn the idle control switch to the “ON” (down) position
for normal (load) engine operation.
l
Check the fuel level on the fuel gauge.
When fuel is low, fill the fuel tank with
clean fresh unleaded automotive gasoline.
Operation
l
If gasoline spillage occurs, completely
wipe up the spilled gasoline.
Check the voltage by referring to the voltmeter on the control
box. When the voltmeter indicates 120 volts, 120 volts from
the 120V receptacles and 240 volts from the 240V receptacle
can be obtained at the same time. Refer to Figure 1, Controls
and Indicators, item 4 on page 10.
Starting
1. Place the idle control switch in the “ON” (up) position.
2. Close the choke. Adjust the opening of the choke valve
according to operating conditions. When the engine is
warm or the air temperature is high, close the choke
valve halfway or open it all the way.
Stopping the Engine
3. Confirm that the main circuit breaker on the generator
CAUTION:
control box is “OFF”.
NEVER stop the engine suddenly while
running at high speeds.
4. Set the operation switch to the “ON” position and grasp
the starting rope and slowly pull it out. The resistance
becomes hardest at a certain position, corresponding
to the compression point. Rewind the rope a little from
that point and pull out sharply.
1. Remove the load from the generator. Place the circuit
breaker in the “OFF” position. Refer to Figure 1, item 5
on page 10. Run the engine (no-load) with the idle control
switch set to the ON position for three to five minutes,
then stop the engine.
5. If the engine fails to start, repeat the procedure.
CAUTION:
l
l
DO NOT pull the starter rope all the way
2. Turn the START/STOP switch to the “STOP” position.
to the end.
3. Never stop the engine suddenly while running at high
speed.
DO NOT release the starter rope after
pulling. Allow it to rewind as soon as
possible.
PAGE 16 — GA-9.7 HZ A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (03/05/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
GA-9.7 HZ — MAINTENANCE
General Inspection
Service Daily
At least daily or prior to each use, the generating set should
be cleaned and inspected for deficiencies. Check for loose,
missing or damaged nuts, bolts or other fasteners. Also check
for fuel or oil leaks.
If engine is operating in very dusty and dry grass conditions.
A clogged air cleaner will result in high fuel consumption,
loss of power and excessive carbon buildup in the
combustion chamber.
Engine Side (Refer to the Engine Instruction Manual)
Cleaning the Fuel Strainer
Check Oil Level
Clean the fuel strainer if it contains dust or water. Remove
dust or water in the strainer cap and wash it in gasoline.
Securely fasten the fuel strainer cap so that fuel will not
leak. Check the fuel strainer every 200 hours of operation or
once a month.
Check the crankcase oil level prior to each use, or when the
fuel tank is filled. Make sure the generating set is level.The
oil level must be between the two notches on the dipstick.
Changing Oil
Spark Plug
Change oil after the first 20 hours of operation. Drain and
refill the engine crankcase every 50 operating hours or once
a week thereafter.Drain crankcase oil into a suitable container
while engine is still warm.Replace the drain plug tightly.Add
oil through the filler hole.
Remove carbon build-up on the spark plug (Figure 5) with a
wire brush. Set the spark plug gap to 0.6—0.7mm (0.024-
0.028 inch).Tighten with a spark plug socket wrench. Clean
the spark plug every 50 operating hours or once a week.
Air Cleaner
Every 50 hours: Remove air cleaner element (std. or heavy
duty types), and wash in kerosene or liquid detergent and
hot water. Wrap foam element in a cloth and squeeze dry.
Wipe heavy duty paper element dry with toweling. Saturate
element with kerosene; squeeze excess from foam element.
Wipe excess from heavy duty paper element.
Figure 5. Spark Plug Gap
GA-9.7 HZ A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (03/05/01) — PAGE 17
Download from Www.Somanuals.com. All Manuals Search And Download.
GA-9.7 HZ — PREPARATION FOR LONG -TERM STORAGE
Generator Storage
For storage of the generating set for over 30 days, the
following is required:
l
l
Drain the fuel tank completely.
Run the engine until the gasoline in the carburetor is
completely consumed.
l
l
l
l
Completely drain the oil from the crankcase and refill
with fresh oil.
Remove the spark plug, pour 2 or 3 cc of SAE 30 oil
into the cylinder and crank slowly to distribute the oil.
Slowly rotate the engine a few times with the starter
Rope and install a new plug.
Pull out the starter rope slowly and stop at the
compression point.
l
l
Clean all external parts of the generating set with a cloth.
Cover the generating set and store in a clean, dry place.
PAGE 18 — GA-9.7 HZ A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (03/05/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
GA-9.7 HZ —WIRING DIAGRAM
GA-9.7 HZ A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (03/05/01) — PAGE 19
Download from Www.Somanuals.com. All Manuals Search And Download.
GA-9.7 HZ —TROUBLESHOOTING (ENGINE)
diagnosis based on the Engine Troubleshooting (Table 4)
information shown below and on the proceeding page. If the
problem cannot be remedied, please leave the unit just as it
is and consult our company's business office or service
plant.
Practically all breakdowns can be prevented by proper
handling and maintenance inspections, but in the event of a
breakdown, please take a remedial action following the
TABLE 4. ENGINE TROUBLESHOOTING
SYMPTOM
POSSIBLE PROBLEM
SOLUTION
Inspect carburetor to see if fuel
is reaching it?
Check fuel line
No Fuel?
Add Fuel
Water in fuel tank?
Fuel filter clogged?
Stuck carburetor?
Spark plug is black?
Flush or replace fuel tank.
Replace fuel filter
Check float mechanism.
Poor starting
(Engine will not start)
Spark plug is fouled. Check tranistor ignition unit.
Insufficient compression, injected air leaking. Carburetor jets are
clogged (overflow).
Spark plug is blue-white?
No spark present at tip of spark
plug?
Tranistor ignition unit broken, high voltage cord cracked or broken.
Start/Stop switch broken. Replace spark plug if fouled.
No oil?
Add oil as required.
Low oil or oil pressure shutdown
sensor is defective?
Check oil level, add oil if necessary. Check automatic oil shutdown
circuit "oil sensor" Replace oil sensor.
Engine will not turn over?
Replace cylinder and piston and if necessary axel joint.
Tighten cylinder head connecting bolts.
Cylinder head connecting bolts
loose?
Cylinder head gasket damaged?
Malfunction of valve seat?
Spark plug is loose?
Replace cylinder head gasket.
Re-seat valves.
Insufficient power output "no
compression"
Replace spark plug.
Replace piston rings.
Worn piston rings?
Malfunction in air-cleaner system,
air filter clogged?
Clean or replace air filter.
Air leaking in from interface
between carburetor and cylinder
head?
Tighten bolts between carburetor and cylinder head. Replace
cylinder head gasket.
Insufficient power output
"compression"
Clean or replace fuel filter.
Clean or replace carburetor.
Check carburetor float.
Malfunction in fuel system?
PAGE 20 — GA-9.7 HZ A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (03/05/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
GA-9.7 HZ —TROUBLESHOOTING (ENGINE)
TABLE 4. ENGINE TROUBLESHOOTING (CONTINUED)
SYMPTOM
POSSIBLE PROBLEM
Malfunction in cooling fan?
Air in-take filter clogged?
SOLUTION
Check or replace cooling fan.
Insufficient power output
"compression" and overheats
Clean or replace air in-take filter.
Over accumulation of exhaust
products?
Clean and check valves.
Check muffler, replace if necessary.
Burns to much fuel
Wrong spark plug?
Replace spark plug with manufactures suggested type spark plug.
Lubricating oil is wrong viscosity? Replace lubricating oil with correct viscosity.
Exhaust color is continiously
"WHITE"
Worn rings?
Replace rings
Air cleanner clogged?
Clean or replace air cleaner.
Adjust choke valve to the correct position.
Choke valve has not been set to
the correct position?
Exhaust color is continiously
"BLACK"
Carburetor defective, seal on
carburetor broken?
Replace carburetor or seal.
Adjust carburetor.
Poor carburetor adjustment
"engine runs too rich?
GA-9.7 HZ A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (03/05/01) — PAGE 21
Download from Www.Somanuals.com. All Manuals Search And Download.
GA-9.7 HZ —TROUBLESHOOTING (GENERATOR)
diagnosis based on the GeneratorTroubleshooting (Table 5)
information shown below and on the preceding page. If the
problem cannot be remedied, please leave the unit just as it
is and consult our company's business office or service
plant.
Practically all generator breakdowns can be prevented by
proper handling and maintenance inspections, but in the event
of a breakdown, please take a remedial action following the
TABLE 5. GENERATOR TROUBLESHOOTING
SYMPTOM
Low voltage
POSSIBLE PROBLEM
Engine speed too low?
SOLUTION
Raise engine speed to rated RPM.
AC voltmeter not working?
Replace Ac voltmeter.
Control box internal wiring
malfunction?
Check control box wiring.
Defective ignition coil?
Check red and green ignition wires. Replace ignition wires if
necessary.
Low voltage. Engine speed
normal 3650 RPM (unloaded),
2500 RPM (idle)
Rotor winding malfunction?
Stator winding malfunction?
Leakage breaker malfunction?
Full power switch malfunction?
Engine speed too high?
Check or replace rotor.
Check or replace stator.
Check or replace CB1 or CB2.
Check full power switch and full power switch circuit.
Lower engine speed to rated RPM.
Check control box wiring.
Voltage output too high.
Voltage output too high. Engine
speed normal 3650 RPM
(unloaded), 2500 RPM (idle)
Control box internal wiring
malfunction
Circuit breaker will not turn on
"NO LOAD"
Defective circuit breaker?
Replace circuit breaker.
Overloaition?
Reduce load or replace breaker.
Check load circuit for short.
Check solenoid.
Circuit breaker will turn on
"LOADED" but trips immediately.
Load circuit is shorted?
Stuck solenoid?
Does not accelerate from low to
high "NO LOAD"
Bad Idle control switch?
Idle control switch malfunction?
Check or replace idle control switch.
Check or replace idle control switch.
Does not accelerate from low to
high "LOAD ACTIVE"
Idle control device malfunction?
Check or replace idle control device.
Check control box wiring.
Control box internal wiring
defective?
PAGE 22 — GA-9.7 HZ A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (03/05/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
GA-9.7 HZ —TROUBLESHOOTING (GENERATOR)
TABLE 5. GENERATOR TROUBLESHOOTING (CONTINUED)
SYMPTOM
POSSIBLE PROBLEM
Defective rotor windings?
Defective solenoid?
SOLUTION
Check or replace rotor.
Check or replace solenoid.
Does not decelerate no
"VOLTAGE OUTPUT".
Defective idle control device?
Defective solenoid?
Check or replace idle control device.
Check or replace idle control device.
Check control box wiring, replace any defective components.
Check or replace solenoid.
Control box wiring malfunction?
Defective solenoid?
Does not decelerate but has
"VOLTAGE OUTPUT".
Idle control device malfunction?
Check or replace idle control device.
GA-9.7 HZ A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (03/05/01) — PAGE 23
Download from Www.Somanuals.com. All Manuals Search And Download.
GA-9.7 HZ — EXPLANATION OF CODE IN REMARKS COLUMN
How to read the marks and remarks used in this parts
book.
Items Found In the “Remarks” Column
Serial Numbers-Where indicated, this indicates a serial
number range (inclusive) where a particular part is used.
Model Number-Where indicated, this shows that the
corresponding part is utilized only with this specific model
number or model number variant.
Items Found In the “Items Number”Column
All parts with same symbol in the number column, , #,
, belong to the same assembly or kit.
+, %, or
*
I
NOTE
If more than one of the same reference number is
listed, the last one listed indicates newest (or latest)
part available.
NOTE
The contents of this catalog are
subject to change without notice.
PAGE 24 — GA-9.7 HZ A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (03/05/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
GA-9.7 HZ — SUGGESTED SPARE PARTS
GA-9.7 1 TO 3 UNITS WITH HONDA
GX610K1VD ENGINE
1 to 3 Units
Qty.
P/N
Description
4 ............ 0601823204 .......... RECTIFIER
4 ............ 0601823754 .......... RELAY
1 ............ 0601807459 .......... CIRCUIT BREAKER
2 ............ 0601812529 .......... RECEPTABLE
1 ............ 0601811032 .......... RECEPTACLE, 250V, 20A
2 ............ 0601811031 .......... RECEPTACLE
1 ............ 0601812597 .......... RECEPTACLE
1 ............ 0601806425 .......... CIRCUIT BREAKER
1 ............ 0601806036 .......... CIRCUIT BREAKER
4 ............ 0601806424 .......... CIRCUIT BREAKER
1 ............ 0601806423 .......... CIRCUIT BREAKER
1 ............ 0601830771 .......... IDLE CONTROL SWITCH
1 ............ 0601830796 .......... OPERATION SWITCH
1 ............ 0663000010 .......... BUTTON STARTER
2 ............ 0601802137 .......... FUSE
2 ............ 0810105900 .......... CAP FUEL STRAINER
1 ............ 0602125032 .......... GAUGE FUEL
2 ............ D9312600104 ....... SUSPENSION RUBBER
2 ............ 7605419004A........ SUSPENSION RUBBER
3 ............ 9807956846 .......... SPARK PLUG
3 ............ 15400PR3004 ....... CARTRIDGE FILTER, OIL
1 ............ 35480ZJ1812 ........ SWITCH ASSY, OIL LEVEL
1 ............ 16100ZJ0892 ........ CARBURETOR ASSY.
3 ............ 17010ZJ1000 ........ ELEMENT SET AIR CLEANER
2 ............ 16910ZE8015 ....... FILTER COMP FUEL
NOTE
Part numbers on this Suggested
Spare Parts List may supercede/
replace the P/N shown in the text
pages of this book.
GA-9.7 HZ A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (03/05/01) — PAGE 25
Download from Www.Somanuals.com. All Manuals Search And Download.
GA-9.7 HZ — GENERATOR ASSY.
GENERATORASSY.
PAGE 26 — GA-9.7 HZ A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (03/05/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
GA-9.7 HZ — GENERATOR ASSY.
GENERATORASSY.
NO
1
PART NO
A6110200103
PART NAME
QTY.
REMARKS
INCLUDES ITEMS W/
ROTOR ASSY.
FIELD ASSY.
RECTIFIER
1
1
2
*
1-1
1-2
1-3
2
*
*
*
7871025004
042006304
BEARING .................................... 1 .....................REPLACES 0071206304
A6113100004
A6113400004
0801086104
0040010000
A6136000103
A6155100102
A6155000002
A6133300003
A6133500004
0040008000
031108160
FAN
1
1
1
1
1
1
1
1
4
4
3
SET BOLT, ROTOR
SET WASHER BEARING
SPRING WASHER
ARMATURE ASSY.
END BRACKET
4
5
6
7
8
END BRACKET
9
COVER, STATOR
SET BOLT, STATOR
SPRING WASHER
10
11
12
13
14
15
16
PLAIN WASHER.......................... 4 .....................REPLACES 0041208000
7871329514
A6155400104
0027105012
011008020
0040008000
A6155400204
GROMMET
COVER, BEARING
MACHINE SCREW
1
1
3
HEX, HEAD BOLT ........................4 .................... REPLACES 0010108020
SPRING WASHER
COVER
RIVET
4
1
4
17
18
0052205008
GA-9.7 HZ A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (03/05/01) — PAGE 27
Download from Www.Somanuals.com. All Manuals Search And Download.
GA-9.7 HZ — CONTROL BOX ASSY.
CONTROL BOX ASSY.
PAGE 28 — GA-9.7 HZ A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (03/05/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
GA-9.7 HZ — CONTROL BOX ASSY.
CONTROL BOX ASSY.
NO
1
PART NO
PART NAME
CONTROL BOX
GROMMET
QTY.
1
REMARKS
A6215000103
0601850102
8511864604
0016906020
0601823204
0027103020
0601823754
0027105016
A6225000103
0601800258
0207003000
0601807459
4341817004
0027404010
0601812529
0601811032
0601811031
0601812597
0021004010
0030004000
0601806425
0601806036
0601806424
0601806423
0027103005
0601830771
0601830796
0663000010
0601815109
0601823853
0021004010
0011305100
0016906020
0601802137
2
2
G-3
3
TERMINAL PLATE
HEX, HEAD BOLT
RECTIFIER
MACHINE SCREW
RELAY
MACHINE SCREW
CONTROL PANEL
AC VOLTMETER
HEX, NUT
1
4
5
5
5
S5VB60
6
5
7
1
MPR-2TS DC12V
8
1
9
1
A65121 00002
8283 120V/240V
10
11
12
13
14
15
16
17
18
19
1
2
CIRCUIT BREAKER
BRACKET, CIRCUIT BREAK
MACHINE SCREW
RECEPTACLE
1
KM52 2P 265V,35A
1
2
1
L14-30R 125/250V,30A,
L6-20R 250V,20A,
RECEPTACLE
1
RECEPTACLE ............................. 1 .......... L5-30R125V,30A, REPLACES 0601811035
RECEPTACLE ............................. 2 .......... 5-20R 120V,20A, REPLACES 0601812598
MACHINE SCREW
10
HEX. NUT................................... 10 .......... REPLACES 0207004000
20
21
22
23
24
25
26
27
28
29
30
31
32
32
CIRCUIT BREAKER
CIRCUIT BREAKER
CIRCUIT BREAKER
CIRCUIT BREAKER
MACHINE SCREW
1
1
CP32E/30N AC250V,30A
CP32E/20N AC250V,30A
CP31E/30N AC250V,30A
CP31E/20N AC250V,20A
1
2
10
1
IDLE CONTROL SWITCH
OPERATION SWITCH
S-1B
ET225N12
1
START SWITCH .......................... 1 .......... ST-403 REPLACES 0602100102
GROUND TERMINAL
IDLE CONTROL DEVICE
MACHINE SCREW
1
1
2
T-381
ND-80
HEX. HEAD BOLT........................ 4 .......... REPLACES 0017105012
HEX. HEAD BOLT
FUSE
4
2
10A AC250V
GA-9.7 HZ A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (03/05/01) — PAGE 29
Download from Www.Somanuals.com. All Manuals Search And Download.
GA-9.7 HZ — PIPE FRAME ASSY.
PIPE FRAME ASSY.
PAGE 30 — GA-9.7 HZ A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (03/05/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
GA-9.7 HZ — PIPE FRAME ASSY.
PIPE FRAME ASSY.
NO
1
PART NO
PART NAME
QTY.
REMARKS
A6418000402
A6415100003
A6365000402
0810105900
PIPE FRAME
FLOOR PANEL
FUEL TANK
1
1
1
2
3
3-1
3-2
4
CAP, FUEL TANK....................... 1 ........ INCLUDES ITEM W/ REPLACES 0810105800
*
FUEL FILTER
DRAIN PLUG
O RING
1
1
1
1
*
3015530004
0150200011
0602125032
011008020
5
6
FUEL GAUGE
7
HEX. HEAD BOLT ..................... 4 ......... REPLACES 0017108020
HEX. HEAD BOLT ...................11 ......... REPLACES 0017108020
8
011008020
9
A6418700103
D9312600104
0207010000
7605419004A
0207010000
0010110045
0207010000
0012308030
A6425400303
A6498200004
0017106016
A6332300204
0017106016
A6418400304
0017106016
A6435300003
0017110025
1622636103Z
1992636004
011606025
BASE
1
2
2
10
11
12
13
14
RUBBER SUSPENSION
HEX. NUT
RUBBER SUSPENSION ........... 2 ......... REPLACES 7605419004
HEX. NUT
2
2
2
2
1
1
8
1
4
1
2
1
4
HEX. HEAD BOLT
HEX. NUT
15
16
HEX. HEAD BOLT
BRACKET
16-1
17
18
19
20
21
22
23
24
25
26
LINING
HEX, HEAD BOLT
COVER
HEX. HEAD BOLT
AIR GUIDE
HEX. HEAD BOLT
HANGER
HEX. HEAD BOLT
ROTARY SOLENOID ................ 1 ......... REPLACES 1620150404
ARM, SOLENOID
1
HEX. HEAD BOLT ..................... 1 ......... REPLACES 0010106025
HEX. NUT .................................. 1 ......... REPLACES 0030006000
020106050
27
28
29
30
31
A6356600404
0017105010
A6359200503
0207006000
0010106040
020106050
WIRE STOPPER
HEX. HEAD BOLT
BRACKET, SOLENOID
HEX. NUT
1
1
1
2
1
HEX. HEAD BOLT
HEX. NUT .................................. 1 ......... REPLACES 0038706000
32
33
34
35
36
37
38
39
40
0017106016
A6356400303
0021005010
A6356600304
0017106016
A6345200204
D1343200204
0805082704
0037806000
HEX. HEAD BOLT
THROTTLE WIRE
MACHINE SCREW
COVER, SOLENOID
HEX. HEAD BOLT
BATTERY SHEET
BATTERY BAND
BATTERY BOLT
WING NUT
4
1
1
1
4
1
1
2
2
41
42
43
0040006000
SPRING WASH
2
2
952404470
PLAIN WASHER ........................ 2 ......... REPLACES 0041206000
0602220600
0602220601
D1343200604
0019206016
0605513143
0605515240
TERMINAL CAP (RED)
TERMINAL CAP (BLK)
TERMINAL CAP
HEX. HEAD BOLT
HOSE
1
1
1
1
1
1
44
45
46
47
HOSE BAND
48
0605515093
HOSE BAND
1
GA-9.7 HZ A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (03/05/01) — PAGE 31
Download from Www.Somanuals.com. All Manuals Search And Download.
GA-9.7 HZ — NAMEPLATE ASSY.
NAMEPLATE ASSY.
PAGE 32 — GA-9.7 HZ A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (03/05/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
GA-9.7 HZ — NAMEPLATE ASSY.
NAMEPLATE ASSY.
NO
PART NO
PART NAME
NAME PLATE
QTY.
REMARKS
ORDER FROM MULTIQUIP SERVICE DEPT. BY
MODEL & SERIAL NUMBER
S-1123
1
0800628504
0800696604
1630645004
7810680104
8700611804
8700611904
B9504000304
D2552000404
0820610804
0820610404
7900636004
8700611524
A6562100003
DECAL; GROUND
1
1
1
1
1
1
1
2
DECAL; BATTERY
3
DECAL; OIL DRAIN
S-1403
4
DECAL; FUEL DRAIN
S-3060
5
DECAL; WARNING DANGEROUS
DECAL; DANGER ELECTRICAL
DECAL; CAUTION HOT PARTS
S-4984
6
S-4985
7
B90400030
D25200040B
8
DECAL; OPERATING INSTRUCTIONS 1
9
DECAL; CAUTION! ................................. 1 .......... REPLACES 0820610304
10
11
12
13
DECAL; WARNING!
1
1
DECAL; 3600RPM ONLY
DECAL; CAUTION OIL LEVEL GAUGE 1
DECAL; MQ MULTIQUIP 9700
2
SEE PAGE 7 FOR DECAL ILLUSTRATIONS.
GA-9.7 HZ A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (03/05/01) — PAGE 33
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX610K1 ENGINE — CYLINDER HEAD ASSY.
CYLINDER HEAD ASSY.
HONDA GX610K1 ENGINE — CYLINDER HEAD
PAGE 34 — GA-9.7 HZ A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (03/05/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX610K1 ENGINE — CYLINDER HEAD ASSY.
CYLINDER HEAD ASSY.
NO
1
PART NO
PART NAME
QTY. REMARKS
12210ZJ1000
12220ZJ1U80
12205ZE2305
12216ZE2300
12251ZJ1003
12311ZJ1000
12314ZJ1000
12391ZJ1000
15611921000
17101ZJ1000
17151ZJ1003
90121ZJ1000
91301805000
92900080250B
9430112200
957010603200
957011007500
957011013000
9807956846
CYLINDER HEAD COMP., R. ........... 1 ..... INCLUDES ITEMS W/
*
*
2
CYLINDER HEAD COMP., L............. 1 ..... INCLUDES ITEMS W/
3
GUIDE, EX. VALVE (OS)
CLIP, VALVE GUIDE
4
4
2
1
1
2
1
1
2
8
1
4
4
4
8
2
2
*
4
*
5
GASKET, CYLINDER HEAD
COVER, HEAD
6
7
COVER, HEAD FILLER
GASKET, HEAD COVER
CAP, OIL
8
9
10
11
12
13
14
15
16
17
18
19
MANIFOLD, IN.
GASKET, IN. MANIFOLD
BOLT, FLANGE (6X25) (CT200)
O-RING (26X2.7)
BOLT, STUD (8X25)
PIN A, DOWEL (12X20)
BOLT, FLANGE (6X32)
BOLT, FLANGE (10X75)
BOLT, FLANGE (10X130)
SPARK PLUG (BPR6ES) (NGK)
GA-9.7 HZ A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (03/05/01) — PAGE 35
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX610K1 ENGINE — CYLINDER BARREL ASSY.
CYLINDER BARREL ASSY.
PAGE 36 — GA-9.7 HZ A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (03/05/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX610K1 ENGINE — CYLINDER BARREL ASSY.
CYLINDER BARREL ASSY.
NO
1
PART NO
PART NAME
QTY.
REMARKS
12000ZJ1810
12356ZJ1000
12358ZJ1000
12372ZE2300
13321ZJ1000
13322ZJ1000
13323ZJ1000
15400PR3004
25523VD6010
31511ZJ1000
35480ZJ1812
90014ZE6000
90018PN3000
90029888000
90031ZE1000
91201ZJ1003
91353671004
9280014000
9405010000
9410914000
957010607509
961406003010
CYLINDER BARREL ASSY. ....................................... 1 ...........INCLUDES ITEMS W/
*
2
COVER, BREATHER
1
1
1
1
1
1
1
2
1
1
3
1
2
2
1
1
2
1
2
2
1
3
4
GASKET, BREATHER COVER
VALVE, BREATHER
5
BEARING A, MAIN (BLUE)
BEARING B, MAIN (BLACK)
BEARING C, MAIN (BROWN)
FILTER, OIL
*
7
10
11
12
15
16
17
18
20
22
23
24
25
26
27
COLLAR, FILTER SETTING
CLAMP, WIRE
SWITCH ASSY., OIL LEVEL
BOLT, FLANGE (6X35)
HOLDER, OIL FILTER
BOLT, FLANGE (6X16)
BOLT, FLANGE (6X32)
OIL SEAL (38X58X11)
O-RING (14MM)
*
BOLT, DRAIN PLUG (14MM)
NUT, FLANGE (10MM)
WASHER, DRAIN PLUG (14MM)
BOLT, FLANGE (6X75)
BEARING, RADIAL BALL (6003)
1
120A0ZJ1000
CYLINDER ASSY.
1
GA-9.7 HZ A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (03/05/01) — PAGE 37
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX610K1 ENGINE — CRANKCASE COVER ASSY.
CRANKCASE COVER ASSY.
PAGE 38 — GA-9.7 HZ A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (03/05/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX610K1 ENGINE — CRANKCASE COVER ASSY.
CRANKCASE COVER ASSY.
NO
1
PART NO
PART NAME
QTY. REMARKS
11300ZJ1000
11381ZJ1000
12105ZAO701
13321ZJ1000
13322ZJ1000
13323ZJ1000
15120ZJ1000
15124ZJ1003
15232ZJ1000
15348ZJ1000
15427ZJ1000
15655ZJ1000
16541ZJ1000
16542ZJ1000
91201ZJ1003
91259NM0000
91302MB6830
93500050100A
9430108140
COVER ASSY., CRANKCASE
GASKET, CASE COVER
BOLT, SEALING
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
3
4
BEARING A, MAIN (BLUE)
BEARING B, MAIN (BLACK)
BEARING C, MAIN (BROWN)
COVER ASSY., OIL PUMP
ROTOR, OIL PUMP (OUTER)
SPRING, RELIEF VALVE
COVER, OIL FILTER
5
6
7
8
9
SCREEN, OIL FILTER
DIPSTICK, OIL
10
11
12
16
17
18
19
20
21
22
23
24
SHAFT, GOVERNOR ARM
FORK, GOVERNOR
OIL SEAL (38X58X11)
OIL SEAL (10X16X4.5)..................... 1 ..... REPLACES 91206333003
O-RING (13X3.0)
2
2
2
3
9
1
2
SCREW, PAN (5X10)
PIN A, DOWEL (8X14)
BOLT, FLANGE (6X20)
BOLT, FLANGE (8X50)
BALL, STEEL (#12) (3/8)
BOLT, SOCKET (6X16)
957010602000
957010805000
9621112000
966000601600
GA-9.7 HZ A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (03/05/01) — PAGE 39
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX610K1 ENGINE — CRANKSHAFT ASSY.
CRANKSHAFT ASSY.
PAGE 40 — GA-9.7 HZ A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (03/05/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX610K1 ENGINE — CRANKSHAFT ASSY.
CRANKSHAFT ASSY.
NO
3
5
PART NO
PART NAME
QTY.
1
1
REMARKS
13310ZJ0880
CRANKSHAFT COMP.
90401ZJ1000
WASHER, CRANKSHAFT THRUST
GA-9.7 HZ A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (03/05/01) — PAGE 41
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX610K1 ENGINE — PISTON ASSY.
PISTON ASSY.
PAGE 42 — GA-9.7 HZ A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (03/05/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX610K1 ENGINE — PISTON ASSY.
PISTON ASSY.
NO
1
PART NO
PART NAME
QTY.
2
REMARKS
13010ZE8601
13011ZE8601
13012ZE8601
13013ZE8601
13101ZJ1000
13102ZJ1000
13103ZJ1000
13104ZJ1000
13111ZJ1000
13210ZJ1000
13211ZJ1003
13212ZJ1003
13213ZJ1003
13214ZJ1003
13215ZJ1003
13216ZJ1003
13217ZJ1003
13213ML0000
13215KM3000
9460118000
RING SET, PISTON (STD)
RING SET, PISTON (0.25)
RING SET, PISTON (0.50)
RING SET, PISTON (0.75)
PISTON
2
2
2
2
2
PISTON (0.25)
2
PISTON (0.50)
2
PISTON (0.75)
2
3
4
5
PIN, PISTON
2
ROD SET, CONNECTING ............................................ 2 ........... INCLUDES ITEM W/
*
BEARING A, CONNECTING ROD (BLUE)
BEARING B, CONNECTING ROD (BLACK)
BEARING C, CONNECTING ROD (BROWN)
BEARING D, CONNECTING ROD (GREEN)
BEARING E, CONNECTING ROD
BEARING F CONNECTING ROD
BEARING G CONNECTING ROD
BOLT, CONNECTING ROD
4
4
4
4
4
4
4
4
4
4
6
*
7
NUT, CONNECTING ROD
CLIP, PISTON PIN (18MM)
*
8
GA-9.7 HZ A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (03/05/01) — PAGE 43
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX610K1 ENGINE — CAMSHAFT ASSY.
CAMSHAFT ASSY.
PAGE 44 — GA-9.7 HZ A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (03/05/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX610K1 ENGINE — CAMSHAFT ASSY.
CAMSHAFT ASSY.
NO
1
PART NO
PART NAME
SEAL, VALVE STEM
QTY.
2
REMARKS
12209ZE8003
14100ZJ1801
14110ZJ1801
14410ZJ1000
14431ZJ1000
14441ZE2000
14461ZJ1000
14568ZJ1800
14569ZJ1801
145762J1801
14577ZJ1801
14578ZJ1800
14579ZJ1800
14580ZJ1800
14581ZJ1801
14586ZJ1800
14711ZJ1000
14721ZJ1000
14751ZE2003
14771ZE2000
14775ZE2010
16512ZJ1000
16522ZJ1000
16523ZJ1000
16524ZJ1000
16529ZJ1000
16531ZJ1003
90012415000
90206250000
90446357000
90901ZJ1003
9451017000
2
CAMSHAFT ASSY. ........................................................ 1 ...........INCLUDES ITEM W/
CAMSHAFT COMP........................................................ 1 ...........INCLUDES ITEM W/
*
3
#
*
4
ROD, PUSH
ARM, VALVE ROCKER
LIFTER, VALVE
SHAFT, ROCKER ARM
SPRING, WEIGHT RETURN
HOLDER, DECOMPRESSION PIN
PIN A, DECOMPRESSION (7.85)
4
4
4
2
1
2
2
5
6
7
8
9
10
*
*
*
PIN B, DECOMPRESSION (7.95) ................................. 2 ...........REPLACES 14577ZJ1800
PIN C, DECOMPRESSION (8.05) ................................. 2 ...........REPLACES 14578ZJ1800
PIN D, DECOMPRESSION (8.15)
PIN E, DECOMPRESSION (8.25)
ROD, DECOMPRESSION
SPRING, DECOMPRESSION PIN HOLDER
VALVE, INLET
VALVE, EX.
SPRING VALVE
RETAINER, IN. VALVE SPRING
SEAT, VALVE SPRING
2
2
1
2
2
2
4
4
2
1
1
1
1
1
1
4
4
1
6
1
11
12
#
*
*
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
HOLDER, GOVERNOR WEIGHT
PLATE, GOVERNOR WEIGHT HOLDER
PIN, GOVERNOR WEIGHT HOLDER
PLATE, GOVERNOR (LOWER)
PLATE, GOVERNOR SLIDER
SLIDER, GOVERNOR
*
*
*
*
*
*
SCREW, TAPPET ADJ.
NUT, TAPPET ADJ.
WASHER, THRUST (17.2MM)
BALL, STEEL (18)
*
*
CIRCLIP (OUTER) (17MM)
GA-9.7 HZ A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (03/05/01) — PAGE 45
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX610K1 ENGINE — RECOIL STARTER ASSY.
RECOIL STARTER ASSY.
PAGE 46 — GA-9.7 HZ A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (03/05/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX610K1 ENGINE — RECOIL STARTER ASSY.
RECOIL STARTER ASSY.
NO
PART NO
PART NAME
QTY. REMARKS
1
28400ZE3W01ZA
28410ZE3W01ZA
28421ZE3W01
28422ZE2W01
28441ZE2W01
28442ZE2W01
28443ZE2W01
28444ZE2W01
28445ZE2W01
28461ZE2W01
28462ZH8003
28469ZE2W01
90004ZE2W01
957010600800
STARTER ASSY., RECOIL R8 (BRT. RED)
CASE COMP. RECOIL STARTER R8 (BRT RED)
PULLEY, RECOIL STARTER
RATCHET STARTER
SPRING, FRICTION
SPRING, STARTER RETURN
SPRING, RATCHET
RETAINER, SPRING
HOLDER, SPRING
GRIP, STARTER
1
1
1
2
1
1
2
1
1
1
INCLUDES ITEMS W/
*
2
*
3
*
4
*
5
*
6
*
7
*
8
*
9
*
10
*
11
12
13
14
ROPE, RECOIL STARTER ...................................... 1 .... REPLACES 28462ZE3W01
GRIP, REINFORCEMENT
SCREW, CENTER
*
*
*
1
1
3
BOLT, FLANGE (6X8)
GA-9.7 HZ A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (03/05/01) — PAGE 47
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX610K1 ENGINE — FAN COVER ASSY.
FAN COVER ASSY.
PAGE 48 — GA-9.7 HZ A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (03/05/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX610K1 ENGINE — FAN COVER ASSY.
FAN COVER ASSY.
NO
2
PART NO
PART NAME
QTY. REMARKS
19611ZJ1800ZB
19612ZJ1000
19614ZJ1000
19615ZJ1000
19617ZJ4000
19631ZJ1000
19632ZJ1000
28405ZJ1801ZB
33713GC2000
90013883000
90018ZE1000
90042ZJ1000
90055ZE1000
90104GF6000
90113GE4000
90683SD9781
9405006000
COVER, FAN R8 (RECOIL STARTER)(BRT.RED)
1
1
1
1
1
1
1
1
6
8
2
4
3
2
2
1
4
2
4
PLATE, R. SIDE
PLATE, L SIDE
5
6
HOOD FAN COVER
COVER, R. SIDE PLATE
SHROUD, R.
7
10
11
12
13
16
17
18
19
20
21
24
25
26
SHROUD, L.
SPACER, RECOIL START MOUNT R8 (BRT RED))
COLLAR B,TAILLIGHT
BOLT, FLANGE (6X12)
BOLT, FLANGE (6X23)
BOLT, STUD (6X75)
SCREW, TAPPING (4X6)
BOLT, FLANGE (6X20)
BOLT, FLANGE (6MM) (BLACK)
CLIP (20MM)
NUT, FLANGE (6MM)
BOLT, FLANGE (6X8)
957010600800
GA-9.7 HZ A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (03/05/01) — PAGE 49
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX610K1 ENGINE — CARBURETOR ASSY.
CARBURETOR ASSY.
PAGE 50 — GA-9.7 HZ A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (03/05/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX610K1 ENGINE — CARBURETOR ASSY.
CARBURETOR ASSY.
NO
1
PART NO
PART NAME
QTY.
REMARKS
12357ZJ1000
15772551000
16010ZG8000
16011382004
16013ZV4005
16015ZJ1000
16016ZJ1010
16024124760
16028ZG8000
16081ZV4650
16100ZJ0892
16148141881
16151ZJ0020
16166ZJ1010
16178548004
16200ZJ1003
16211ZJ1000
TUBE, BREATHER
CLIP, BREATHER TUBE
GASKET SET
1
1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
#
*
*
*
*
VALVE SET, FLOAT ...................................... 1 .......... REPLACES 16011GK0891
FLOAT SET
1
CHAMBER SET, FLOAT............................... 1 .......... INCLUDES ITEMS W/
#
SCREW SET
1
1
1
4
#
SCREW SET,DRAIN
SCREW SET
*
*
SCREW-WASHER
*
CARBURETOR ASSY. (BG21E B) ............... 1 .......... INCLUDES ITEMS W/
*
CAP, CHOKE LEVER DUST
JET SET (#60)
1
1
*
*
*
*
*
NOZZLE, MAIN ............................................. 1 .......... REPLACES 16166ZJ0000
O-RING (5.8X1.9)
VALVE ASSY., SOLENOID
INSULATOR, CARBURETOR
GASKET, CARBURETOR
GASKET, AIR CLEANER
1
1
1
2
1
18
19
20
16221ZG8000
17228ZG8003
17410ZJ1000
ELBOW COMP., AIR CLEANER................... 1 .......... INCLUDES ITEMS W/++
COLLAR, DISTANCE
CLIP B, CABLE
SCREW-WASHER (5X12)
CLIP, TUBE (B8)
BULK HOSE, VAC (4.5X460)
BOLT, FLANGE (6X105)
JET SET, MAIN (#88)
JET SET, MAIN (#82 HIGH ALTITUDE) 1
JET SET, MAIN (#85 HIGH ALTITUDE) 1
21++ 19024ZA0000
2
1
2
1
1
2
1
22
23
24
25
26
27
90682959661
938920501218
9500202080
950054546020
958010610508
99201ZG80880
99201ZG80820
99201ZG80850
*
*
GA-9.7 HZ A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (03/05/01) — PAGE 51
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX610K1 ENGINE — AIR CLEANER ASSY.
AIR CLEANER ASSY.
PAGE 52 — GA-9.7 HZ A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (03/05/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX610K1 ENGINE — AIR CLEANER ASSY.
AIR CLEANER ASSY.
NO
1
PART NO
PART NAME
QTY.
REMARKS
17010ZJ1000
17216ZJ1000
17217ZJ1000
17218ZJ1000
17220ZJ1000
17231ZJ1000
17232ZJ1000
17237ZJ1000
17251ZJ1000
17255758000
17257HB3000
90017ZJ1000
90018ZE1000
90120102000
93500040200A
93500040250G
938910501608
957000601800
ELEMENT SET, AIR CLEANER ................... 1 .......... INCLUDES ITEMS W/
*
2
GASKET A, ELEMENT
1
1
1
1
1
1
1
1
1
1
1
3
4
1
1
2
*
3
GASKET B, ELEMENT
*
4
FILTER (OUTER)
5
HOUSING COMP., AIR CLEANER
COVER, AIR CLEANER
GROMMET, AIR CLEANER
HOSE, AIR CLEANER
6
7
8
9
TUBE, AIR CLEANER CONN.
BAND, AIR CLEANER CONN. TUBE
BAND, AIR CLEANER (B)
BOLT, AIR CLEANER
10
11
13
14
15
16
17
18
19
BOLT, FLANGE (6X23)
COLLAR, AIR CLEANER HOUSING
SCREW, PAN (4X20)
SCREW, PAN (4X25)
SCREW, WASHER
BOLT, FLANGE (6X18) ................................ 1 .......... REPLACES 957010601800
GA-9.7 HZ A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (03/05/01) — PAGE 53
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX610K1 ENGINE — MUFFLER ASSY.
MUFFLER ASSY.
PAGE 54 — GA-9.7 HZ A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (03/05/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX610K1 ENGINE — MUFFLER ASSY.
MUFFLER ASSY.
NO
1
PART NO
PART NAME
MUFFLER KIT
QTY. REMARKS
1
NOT AVAILABLE, SEE COMPONENTS
2
18310ZJ1000
18321ZJ1000
18330ZJ1601
18333ZJ1000
18396ZJ1003
957010600800
957010801400
957010802000
18333ZJ1000
99405008000
MUFFLER COMP.............................. 1 ..... 18310ZJ1003
PROTECTOR,MUFFLER ................ 1 ..... 18321ZJ1003
3
4
PIPE COMP., EX.
1
5
STAY, MUFFLER .............................. 1 ..... 18338ZJ1003
6
BAND ASSY.
1
6
4
4
2
4
7
BOLT, FLANGE (6X8)
BOLT, FLANGE (8X14)
BOLT, FLANGE (8X20)
GASKET,EX,PIPE
8
9
10
11
NUT,FLANGE(8mm)
GA-9.7 HZ A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (03/05/01) — PAGE 55
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX610K1 ENGINE — FUEL PUMP ASSY.
FUEL PUMP ASSY.
PAGE 56 — GA-9.7 HZ A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (03/05/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX610K1 ENGINE — FUEL PUMP ASSY.
FUEL PUMP ASSY.
NO
1
PART NO
PART NAME
QTY.
1
REMARKS
16700ZJ1003
16711ZJ1800
16910ZE8015
19905ZA8701
35806752630
90617SA0003
950014511040
950015519540
950015521540
9500202080
950024105008
950033601620
957010600800
957010601400
PUMP ASSY., FUEL
2
STAY, FUEL PUMP
1
4
STRAINER COMP., FUEL
GROMMET, WIRE
1
5
1
6
BASE, CLIP
1
7
CLIP, WIRE HARNESS
BULK HOSE, FUEL (4.5X110)
BULK HOSE, FUEL (5.5X195)
BULK HOSE, FUEL (5.5X215)
CLIP, TUBE (B8)
1
8
1
9
1
10
11
12
13
14
15
1
2
CLIP, TUBE (10.5MM)
TUBE, VINYL (11X13X160)
BOLT, FLANGE (6X8)
BOLT, FLANGE (6X14)
4
1
2
2
GA-9.7 HZ A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (03/05/01) — PAGE 57
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX610K1 ENGINE — FLYWHEEL ASSY.
FLYWHEEL ASSY.
PAGE 58 — GA-9.7 HZ A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (03/05/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX610K1 ENGINE — FLYWHEEL ASSY.
FLYWHEEL ASSY.
NO
1
PART NO
PART NAME
QTY. REMARKS
19511ZJ1000
28451ZJ1801
28453ZJ1801
31110ZJ1811
90013ZJ1800
90201ZG3000
90401ZG3000
90741ZE2000
957010801600
FAN, COOLING
1
1
1
1
1
1
1
1
3
3
PULLEY, STARTER
6
8
10
11
12
13
15
SPACER, STARTER PULLEY MT.
FLYWHEEL COMP.
BOLT, UBS (12X28)
NUT, FLANGE (20MM)
WASHER (20MM)
KEY, SPECIAL WOODRUFF (25X18)
BOLT, FLANGE (8X16)
GA-9.7 HZ A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (03/05/01) — PAGE 59
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX610K1 ENGINE — IGNITION COIL ASSY.
IGNITION COIL ASSY.
PAGE 60 — GA-9.7 HZ A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (03/05/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX610K1 ENGINE — IGNITION COIL ASSY.
IGNITION COIL ASSY.
NO
1
PART NO
PART NAME
QTY.
1
REMARKS
30500ZJ1013
30518ZJ1000
30550ZJ1013
30700ZJ1003
31630ZJ1003
31740ZJ1003
63312ZA7000
90014ZE6000
901219052000
90658SA0003
90673GJ5003
901504750003
957010600800
COIL ASSY., R. IGNITION
GROMMET, IGNITION WIRE
COIL ASSY., L. IGNITION
CAP ASSY., NOISE SUPPRESSER
COIL ASSY., CHARGE (12V/3A)
DIODE ASSY., ENGINE STOP
GROMMET, TOOL
2
2
3
1
4
2
5
1
7
1
8
1
9
BOLT, FLANGE (6X35)
BOLT, FLANGE (6X25)
CLIP, WIRE HARNESS
CLIP, CORD
CLIP, WIRE HARNESS
BOLT, FLANGE (6X8)
2
11
12
13
14
15
2
1
1
1
1
GA-9.7 HZ A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (03/05/01) — PAGE 61
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX610K1 ENGINE — STARTER MOTOR ASSY.
STARTER MOTOR ASSY.
PAGE 62 — GA-9.7 HZ A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (03/05/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX610K1 ENGINE — STARTER MOTOR ASSY.
STARTER MOTOR ASSY.
NO
1
PART NO
PART NAME
QTY. REMARKS
1
1
31200ZJ1004
31243ZJ1800
32402ZJ1810
32411KB9930
32411402000
35850ZJ1811
9405006000
9407006080
9430110120
957010811000
MOTOR ASSY., STARTER
2
BRACKET, STARTER MAGNETIC SET.
3
CABLE, MAGNET SWITCH ............................. 1 ......... INCLUDES ITEMS W/
*
4
COVER A, MAGNETIC SWITCH
COVER, STARTER. MOTOR TERMINAL
SWITCH ASSY., STARTER MAGNETIC
NUT, FLANGE (6MM)
1
1
1
2
2
2
2
*
5
*
6
7
8
NUT, WASHER (6MM)
9
PIN, DOWEL (10X12)
10
BOLT, FLANGE (8X10)
GA-9.7 HZ A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (03/05/01) — PAGE 63
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX610K1 ENGINE — GOVERNOR/CONTROL ASSY.
GOVERNOR/CONTROL ASSY.
PAGE 64 — GA-9.7 HZ A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (03/05/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX610K1 ENGINE — GOVERNOR/CONTROL ASSY.
GOVERNOR/CONTROL ASSY.
NO
1
PART NO
PART NAME
JOINT, ROD
QTY.
1
REMARKS
16263ZE3790
16265ZJ1U80
16500ZJ1U80
16534ZJ1U80
16534Z16680
16550ZJ1U80
16555ZJ1000
16561ZG1000
16561ZJ1000
16562ZJ1000
16574ZE1000
16575ZH8000
16576891000
16578ZE1000
16584883300
16592ZJ1000
16628ZJ1000
16649ZJ1000
17951ZG1000
90013883000
90015ZE3790
90114SA0000
90605230000
9350004006OH
9350005012OH
9350005025OH
93500050160A
93500050300H
9405006000
2
STAY ASSY., AUTO THROTTLE ...... 1 ............INCLUDES ITEMS W/
*
3
CONTROL ASSY. ............................. 1 ............INCLUDES ITEMS W/# #
4
5
6
8
9
+
SPRING, RETURN
SPRING, STARTER
1
1
ARM COMP., GOVERNOR............... 1 ........... INCLUDES ITEMS W/+
ROD, GOVERNOR
1
1
1
1
1
1
1
1
2
1
1
1
1
2
1
1
2
2
1
2
2
2
1
#
SPRING, GOVERNOR
SPRING, GOVERNOR
SPRING, THROTTLE RETURN
SPRING, LEVER
10
11
13
14
15
16
17
18
21
22
23
#
#
WASHER, CONTROL LEVER
HOLDER, CABLE
#
*
#
SPACER, CONTROL LEVER
SPRING, CONTROL ADJ.
SPRING, CABLE RETURN
ROD, CHOKE KNOB
HOLDER, CHOKE KNOB
KNOB, CHOKE
#
*
#
#
#
24
25
26
27
28
29
30
31
32
BOLT, FLANGE (6X12)
BOLT, GOVERNOR ARM
NUT, SELFLOCK (6MM)
CIRCLIP (5MM)
#
*
SCREW, PAN (4X6)
*
#
SCREW, PAN (5X12)
SCREW, PAN (5X25)
SCREW, PAN (5X16)
SCREW, PAN (5X30)
NUT, FLANGE (6MM)
#
#
+
*
34
GA-9.7 HZ A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (03/05/01) — PAGE 65
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX610K1 ENGINE — LABELS
LABELS
PAGE 66 — GA-9.7 HZ A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (03/05/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX610K1 ENGINE — LABELS
LABELS
NO
1
PART NO
PART NAME
QTY.
REMARKS
87101ZJ0000
87152ZJ0000
87522ZJ1000
87532ZH8810
MARK, EMBLEM (GX610)
LABEL, SPECIFICATION (GX610)
LABEL, CAUTION
1
1
1
1
2
3
5
MARK, OIL ALERT (E)
GA-9.7 HZ A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (03/05/01) — PAGE 67
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX610K1 ENGINE —GASKET KIT
GASKET KIT
NO
PART NO
PART NAME
QTY. REMARKS
061A1ZJ1000
11381ZJ1000
12251ZJ1003
12358ZJ1000
12391ZJ1000
16221ZG8000
17151ZJ1003
17228ZG8003
18333ZJ1000
91301805000
GASKET KIT ..................................... 1 ........... INCLUDES ITEMS W/
*
1
2
GASKET, CASE COVER
GASKET, CYLINDER HEAD
GASKET, BREATHER COVER
GASKET, HEAD COVER
GASKET, CARBURETOR
GASKET, IN. MANIFOLD
GASKET, AIR CLEANER
GASKET, EX. PIPE
1
2
1
2
2
2
1
2
1
*
3
*
4
*
5
*
6
*
7
*
8
*
9
ORING (26X2.7)
*
PAGE 68 — GA-9.7 HZ A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (03/05/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
Effective: July 1, 2000
TERMS AND CONDITIONS OF SALE — PARTS
PAYMENT TERMS
4. Freight is at the sender’s expense. All
partsmustbereturnedfreightprepaidto
Multiquip’sdesignatedreceivingpoint.
PRICINGANDREBATES
Terms of payment for parts are net 10 days.
Prices are subject to change without prior
notice.Pricechangesareeffectiveonaspecific
dateandallordersreceivedonorafterthatdate
willbebilledattherevisedprice. Rebatesfor
price declines and added charges for price
increaseswillnotbemadeforstockonhandat
thetimeofanypricechange.
5. Parts must be in new and resalable
condition,intheoriginalMultiquippackage
(ifany),andwithMuiltiquippartnumbers
clearlymarked.
FREIGHTPOLICY
All parts orders will be shipped collect or
prepaidwiththechargesaddedtotheinvoice.
All shipments are F.O.B. point of origin.
Multiquip’sresponsibilityceaseswhenasigned
manifesthasbeenobtainedfromthecarrier,
andanyclaimforshortageordamagemustbe
settledbetweentheconsigneeandthecarrier.
6. Thefollowingitemsarenotreturnable:
Multiquip reserves the right to quote and sell
directtoGovernmentagencies,andtoOriginal
Equipment Manufacturer accounts who use
our products as integral parts of their own
products.
a. Obsolete parts. (If an item is listed
inthepartspricebookasbeing
replaced by another item, it is
obsolete.)
b. Any parts with a limited shelf life
(such as gaskets, seals, “O” rings,
andotherrubberparts)thatwere
purchasedmorethansixmonths
priortothereturndate.
MINIMUMORDER
SPECIALEXPEDITINGSERVICE
TheminimumchargeforordersfromMultiquip
is $15.00 net. Customers will be asked for
instructionsregardinghandlingofordersnot
meetingthisrequirement.
A$20.00to$50.00surchargewillbeaddedto
theinvoiceforspecialhandlingincludingbus
shipments, insured parcel post or in cases
where Multiquip must personally deliver the
partstothecarrier.
c. Anylineitemwithanextendeddealer
netpriceoflessthan$5.00.
d. Special order items.
RETURNEDGOODSPOLICY
e. Electricalcomponents.
Returnshipmentswillbeacceptedandcredit
will be allowed, subject to the following
provisions:
LIMITATIONSOFSELLER’SLIABILITY
f.
Paint,chemicals,andlubricants.
Multiquip shall not be liable here under for
damagesinexcessofthepurchasepriceofthe
itemwithrespecttowhichdamagesareclaimed,
andinnoeventshallMultiquipbeliableforloss
of profit or good will or for any other special,
consequentialorincidentaldamages.
g. Decalsandpaperproducts.
h. Itemspurchasedinkits.
1. AReturnedMaterialAuthorizationmust
beapprovedbyMultiquippriortoshipment.
7. Thesenderwillbenotifiedofanymaterial
receivedthatisnotacceptable.
2. ToobtainaReturnMaterialAuthorization,
alistmustbeprovidedtoMultiquipParts
Sales that defines item numbers, 8. Such material will be held for 5 working
quantities,anddescriptionsoftheitemsto
bereturned.
days from notification, pending
instructions. If a reply is not received
within5days,thematerialwillbereturned
tothesenderathisexpense.
LIMITATIONOFWARRANTIES
a. Thepartsnumbersanddescriptions
mustmatchthecurrentpartsprice
list.
Nowarranties,expressorimplied,aremadein
connection with the sale of parts or trade
accessories nor as to any engine not
manufacturedbyMultiquip.Suchwarranties
made in connection with the sale of new,
complete units are made exclusively by a
statement of warranty packaged with such
units, and Multiquip neither assumes not
authorizes any person to assume for it any
other obligation or liability whatever in
connectionwiththesaleofitsproducts.Apart
fromsuchwrittenstatementofwarranty,there
arenowarranties,express,impliedorstatutory,
which extend beyond the description of the
productsonthefacehereof.
9. Creditonreturnedpartswillbeissuedat
dealer net price at time of the original
purchase,lessa15%restockingcharge.
b. The list must be typed or computer
generated.
10. In cases where an item is accepted for
which the original purchase document
can not be determined, the price will be
basedonthelistpricethatwaseffective
twelvemonthspriortotheRMAdate.
c. Thelistmuststatethereason(s)for
thereturn.
d. The list must reference the sales
order(s)orinvoice(s)underwhich
theitemswereoriginallypurchased.
11. Credit issued will be applied to future
purchasesonly.
e. Thelistmustincludethenameand
phonenumberoftheperson
requestingtheRMA.
3. A copy of the Return Material
Authorizationmustaccompanythereturn
shipment.
GA-9.7 HZ A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (03/05/01) — PAGE 69
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS AND OPERATION MANUAL
HERE'S HOW TO GET HELP
PLEASE HAVE THE MODEL AND SERIAL NUMBER
ON-HANDWHEN CALLING
PARTS DEPARTMENT
800/427-1244 or 310/537-3700
FAX: 800/672-7877 or 310/637-3284
SERVICE DEPARTMENT
800/478-1244 or 310/537-3700
FAX: 310 - 537-4259
WARRANTY DEPARTMENT
800/421-1244, EXT. 279 or 310/537-3700
FAX: 310 - 537-1173
MAIN
800/421-1244 or 310/537-3700
FAX: 310 - 537-3927
Manufactured for MULTIQUIP INC.
by
DENYO MANUFACTURING CO., USA
MULTIQUIP INC.
POST OFFICE BOX 6254
CARSON, CA 90749
310-537-3700 • 800-421-1244
FAX:310-537-3927
WWW:multiquip.com
Atlanta • Boise • Dallas • Houston • Newark
Quebec, Canada • Manchester, UK • Rio De Janiero, BR • Guadalajara, MX
Download from Www.Somanuals.com. All Manuals Search And Download.
|