Multiquip Saw FS3SP User Manual
PARTS AND OPERATION MANUAL  
CONCRETE SAW  
MODELSFS3SP  
Revision #0 (07/15/02)  
MULTIQUIPINC.  
18910 WILMINGTON AVE.  
PARTS DEPARTMENT:  
800-427-1244  
CARSON, CALIFORNIA 90746 FAX: 800-672-7877  
310-537-3700  
800-421-1244  
SERVICE DEPARTMENT/TECHNICAL ASSISTANCE:  
800-478-1244  
FAX:310-537-3927  
FAX:310-631-5032  
E-mail:[email protected] • www:multiquip.com  
Atlanta • Boise • Dallas • Houston • Newark  
Montreal, Canada • Manchester, UK  
Rio De Janiero, Brazil • Guadalajara, Mexico  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HERE'S HOW TO GET HELP  
PLEASE HAVE THE MODEL AND SERIAL NUMBER  
ON-HAND WHEN CALLING  
PARTS DEPARTMENT  
800-427-1244 or 310-537-3700  
FAX: 800-672-7877 or 310-637-3284  
SERVICE DEPARTMENT/TECHNICAL ASSISTANCE  
800-478-1244 or 310-537-3700  
FAX: 310-537-4259  
WARRANTY DEPARTMENT  
888-661-4279, or 310-661-4279  
FAX: 310-537-1173  
MAIN  
800-421-1244 or 310-537-3700  
FAX: 310-537-3927  
MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #0 (07/15/02) — PAGE 3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TABLE OF CONTENTS  
Here's How To Get Help ........................................... 3  
Table Of Contents .................................................... 4  
Parts Ordering Procedures ...................................... 5  
Safety Message Alert Symbols .............................6-7  
Decals ...................................................................... 8  
Rules for Safe Operation ....................................9-11  
Dimensions ............................................................ 12  
Weights .................................................................. 13  
Basic Components ................................................. 14  
Basic Console Components .............................15-16  
Basic Engine Components................................17-18  
General Information ..........................................19-20  
Blade Shaft Assembly .......................................46-47  
Engine Mount Assembly ...................................48-49  
Pointers and Covers Assembly .........................50-51  
Water System Assembly ...................................52-53  
Basic Platform Assembly...................................54-55  
Blade Mist 20-Inch Assembly............................56-57  
Manual Raise and Lower Assembly .................58-59  
Battery Box Assembly....................................... 64-65  
Platform(Bare) Assembly.................................. 66-67  
Transmission Assembly ................................... 69-71  
Engines  
Engine Assemblies............................................72-73  
MQ-Whiteman — FS3SP  
Concrete Saw  
Terms and Conditions Of Sale — Parts ................. 75  
Inspection Engine .............................................21-22  
Inspection Blade .................................................... 23  
Inspection Blade Placement .................................. 24  
Inspection-Guards, Covers, and V-Belts ...........25-26  
Initial Start-Up ...................................................27-28  
Operation ..........................................................29-30  
Maintenance .....................................................31-34  
Explanation Of Codes In Remarks Column ........... 36  
Suggested Spare Parts .......................................... 37  
Troubleshooting (Engine)..................................38-39  
Name Plate and Decals.................................... 40-41  
Under Carriage Assembly.................................42-43  
Rear Axle Assembly......................................... 44-45  
22  
NOTE  
Specification and part number  
are subject to change without  
notice.  
PAGE 4 — MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #0 (07/15/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PARTS ORDERING PROCEDURES  
■ Dealer account number  
■ Dealer name and address  
■ Shipping address (if different than billing address)  
■ Return fax number  
■ Applicable model number  
■ Quantity, part number and description of each part  
■ Specify preferred method of shipment:  
UPS Ground  
•
UPS Second Day or Third Day*  
•
UPS Next Day*  
•
Federal Express Priority One (please provide us with your Federal  
Express account number)*  
•
Airborne Express*  
•
Truck or parcel post  
•
*Normally shipped the same day the order is received, if prior to 2PM west coast time.  
Earn Extra Discounts when  
you order by FAX!  
All parts orders which include complete part numbers  
and are received by fax qualify for the following extra  
discounts:  
Number of  
line items ordered  
Additional Discount  
1-9 items  
3%  
10+ items**  
5%  
Get special freight allowances  
when you order 10 or more  
line items via FAX!**  
Now! Direct TOLL-FREE access  
to our Parts Department!  
■
UPS Ground Service at no charge for freight  
■
PS Third Day Service at one-half of actual freight cost  
Toll-free nationwide:  
800-421-1244  
No other allowances on freight shipped by any other carrier.  
**Common nuts, bolts and washers (all items under $1.00 list price)  
do not count towards the 10+ line items.  
Toll-free FAX:  
*DISCOUNTS ARE SUBJECT TO CHANGE*  
800/6-PARTS-7 • 800-672-7877  
Fax order discount and UPS special programs revised June 1, 1995  
MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #0 (07/15/02) — PAGE 5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FS3SP CONCRETE SAW — SAFETY MESSAGE ALERT SYMBOLS  
FORYOUR SAFETY ANDTHE SAFETY OF OTHERS!  
HAZARD SYMBOLS  
Safety precautions should be followed at all times when  
operating this equipment. Failure to read and understand the  
Safety Messages and Operating Instructions could result in  
injury to yourself and others.  
Lethal Exhaust Gases  
Engine exhaust gases contain poisonous  
carbon monoxide. This gas is colorless and  
odorless, and can cause death if inhaled.  
NEVER operate this equipment in a confined  
area or enclosed structure that does not  
provide ample free flow air.  
NOTE  
This Owner's Manual has been developed to provide  
complete instructions for the safe and efficient operation  
of the MQWhiteman FS3SP Concrete Saws. Depending  
on the power plant you have selected, please refer to  
the engine manufacturers instructions for data relative  
to its safe operations.  
Before using this Concrete Saw, ensure that the  
operating individual has read and understands all  
instructions in this manual.  
Explosive Fuel  
Gasoline is extremely flammable, and its  
vapors can cause an explosion if ignited. DO  
NOT start the engine near spilled fuel or  
combustible fluids. DO NOT fill the fuel tank  
while the engine is running or hot. DO NOT  
overfill tank, since spilled fuel could ignite if it  
comes into contact with hot engine parts or  
sparks from the ignition system. Store fuel in  
approved containers, in well-ventilated areas  
and away from sparks and flames. NEVER  
use fuel as a cleaning agent.  
SAFETY MESSAGE ALERT SYMBOLS  
The three (3) Safety Messages shown below will inform you  
about potential hazards that could injure you or others. The  
Safety Messages specifically address the level of exposure to  
the operator, and are preceded by one of three words: DANGER,  
WARNING, or CAUTION.  
Burn Hazards  
DANGER: You WILL be KILLED or  
SERIOUSLY injured if you do not follow  
directions.  
Engine components can generate extreme heat.  
To prevent burns, DO NOT touch these areas  
while the engine is running or immediately after  
operations. Never operate the engine with heat  
shields or heat guards removed.  
WARNING: You CAN be KILLED or  
SERIOUSLY injured if you do not follow  
directions.  
Rotating Parts  
CAUTION: You CAN be injured if you  
do not follow directions.  
NEVER operate equipment with covers, or  
guards removed. Keep fingers, hands, hair and  
clothing away from all moving parts to prevent  
injury.  
Potential hazards associated with Concrete Saw operations  
will be referenced with Hazard Symbols which appear  
throughout this manual, and will be referenced in conjunction  
with Safety Message Alert Symbols.  
PAGE 6 — MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #0 (07/15/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FS3SP CONCRETE SAW — SAFETY MESSAGE ALERT SYMBOLS  
Accidental Starting  
Respiratory Hazard  
ALWAYS place the ON/OFF switch in the OFF  
position, remove key and/or disconnect the  
spark plug lead before servicing the engine  
or equipment. Ground the lead to prevent  
sparks that could ignite a fire.  
ALWAYS wear approved respiratory  
protection.  
Over Speed Conditions  
Sight and Hearing hazard  
NEVER tamper with the factory settings of the  
engine governor or settings. Personal injury  
and damage to the engine or equipment can  
result if operating in speed ranges above  
maximum allowable.  
ALWAYS wear approved eye and hearing  
protection.  
Guards and Covers In Place  
Equipment Damage Messages  
Other important messages are provided throughout this manual  
to help prevent damage to your concrete saw, other property, or  
the surrounding environment.  
NEVER operate the saw without blade guards  
and covers in place. Adhere to safety guidelines  
ANSI American National Standards Institute,  
OSHA or other applicable local regulations.  
NOTE  
This concrete saw, other property, or the  
surrounding environment could be damaged  
if you do not follow instructions.  
MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #0 (07/15/02) — PAGE 7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FS3SP CONCRETE SAW — DECALS  
Machine Safety Decals  
The FS3SP Series concrete saws are equipped with a number of safety decals (Figure 1). These decals are provided for operator safety  
and maintenance information. The illustration below shows these decals as they appear on either concrete saw. Should any of these  
decals become unreadable, replacements can be obtained from you dealer.  
Figure 1. FS3SP Decals  
PAGE 8 — MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #0 (07/15/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FS3SP CONCRETE SAW — RULES FOR SAFE OPERATION  
■
NEVER touch the hot exhaust manifold, muffler or cylinder. Allow  
these parts to cool before  
servicing engine or saw.  
WARNING:  
Failure to follow instructions in this manual may  
lead to serious injury or even death! This  
equipment is to be operated by trained and  
qualified personnel only!This equipment is for  
industrial use only.  
The following safety guidelines should always be used when  
operating the MQ Whiteman FS3SP Concrete Saws:  
■
■
HighTemperatures – Allow the engine to cool before adding  
fuel or performing service and maintenance functions. Contact  
with hot components can cause serious burns.  
GENERAL SAFETY  
■
DO NOT operate or service this equipment  
beforereadingthisentiremanual.  
The engine section of this saw requires an adequate free flow  
of cooling air. NEVER operate the saw in any enclosed or  
narrow area where free flow of the air is  
restricted. If the air flow is restricted it  
will cause serious damage to the saw  
or engine and may cause injury to  
people. Remember the saw's engine  
gives off DEADLY carbon monoxide  
gas.  
■
■
This equipment should not be operated by persons under 18  
years of age.  
NEVER operate this equipment without proper  
protective clothing, shatterproof glasses, steel-  
toed boots and other protective devices required  
by the job.  
■
■
ALWAYS refuel in a well-ventilated area, away from sparks  
and open flames.  
ALWAYS use extreme caution when working with flammable  
liquids. When refueling, stop the engine and allow it to cool.  
DO NOT smoke around or near the machine. Fire or explosion  
could result from fuel vapors, or if fuel is  
■
■
NEVER operate this equipment when not  
feelingwellduetofatigue, illnessor taking  
medicine.  
spilled on a hot engine.  
■
NEVER operate the saw in an explosive  
atmosphere or near combustible materials.  
An explosion or fire could result causing  
severe bodily harm or even death.  
NEVER operate this equipment under the  
influence or drugs or alcohol.  
■
■
Topping-off to the fuel filler port is dangerous, as it tends to  
spill fuel.  
■
NEVER use accessories or attachments, which are not  
recommended by Multiquip for this equipment. Damage to  
the equipment and/or injury to user may result.  
NEVER use fuel as a cleaning agent.  
■
■
■
The manufacturer does not assume responsibility for any  
accident due to equipment modifications.  
Whenever necessary, replace nameplate, operation and  
safety decals when they become difficult to read.  
ALWAYS check the machine for loosened threads or bolts  
before starting.  
MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #0 (07/15/02) — PAGE 9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FS3SP CONCRETE SAW — RULES FOR SAFE OPERATION  
GENERAL SAFETY  
DIAMOND BLADE SAFETY  
■
ALWAYS read, understand, and follow procedures in  
Operator’s Manual before attempting to operate equipment.  
■
Use appropriate steel centered diamond blades manufactured  
for use on concrete saws.  
■
ALWAYS be sure the operator is familiar with proper safety  
precautions and operating techniques before using the saw.  
■
ALWAYS inspect diamond blades before each use. The blade  
should exhibit no cracks, dings, or flaws in the steel centered  
core and/or rim. Center (arbor) hole must be undamaged and  
true.  
■
■
■
Stop the engine when leaving the saw unattended.  
Block the unit when leaving or when using on a slope.  
■
Examine blade flanges for damage, excessive wear and  
cleanliness before mounting blade. Blade should fit snugly on  
the shaft and against the inside/outside blade flanges.  
Maintain this equipment in a safe operating condition at all  
times.  
■
■
■
■
ALWAYS stop the engine before servicing, adding fuel and  
oil.  
■
■
Ensure that the blade is marked with an operating speed greater  
than the blade shaft speed of the saw.  
NEVER Run engine without air filter. Severe engine damage  
may occur.  
Only cut the material that is specified by the diamond blade.  
Readthespecificationsofthediamondbladetoensuretheproper  
tool has been matched to the material being cut.  
ALWAYS service air cleaner frequently to prevent carburetor  
malfunction.  
■
■
ALWAYS keep blade guards in place. Exposure of the diamond  
blade must not exceed 180 degrees.  
ALWAYS store equipment properly when it is not being used.  
Equipment should be stored in a clean, dry location out of the  
reach of children.  
Ensure that the diamond blade does not come into contact with  
the ground or surface during transportation. DO NOT drop the  
diamond blade on ground or surface.  
■
■
NEVER use accessories or attachments, which are not  
recommended by Multiquip for this equipment. Damage to  
the equipment and/or injury to user may result.  
■
■
The engine governor is designed to permit maximum engine  
speed in a no-load condition. Speeds that exceed this limit may  
cause the diamond blade to exceed the maximum safe allowable  
speed.  
NEVERoperatethissawinareasthatcontaincombustiblematerial  
or fumes. Fire and/or explosions may result from errant sparks  
from the equipment.  
Ensure that the blade is mounted for proper operating direction.  
WARNING:  
SAWTRANSPORTATION SAFETY  
■
DO NOT operate this equipment unless all  
■
Use the lifting bail and appropriate lifting equipment to ensure  
the safe movement of the saw.  
guards and safety devices are attached and in  
place.  
■
■
■
DO NOT use the handle bars and/or front pointer as lifting points.  
NEVER tow the saw behind a vehicle.  
■
■
Caution must be exercised while servicing this equipment.  
Rotating and moving parts can cause injury if contacted.  
Ensure that both pointer bars are positioned appropriately to  
minimize their exposure during transportation.  
Keep all inexperienced and unauthorized people away from  
the equipment at all times.  
■
■
Safeguardagainstextremesawattitudesrelativetolevel. Engines  
tippedtoextremeanglesmaycauseoiltogravitateintothecylinder  
head making the engine difficult to start.  
■
■
Unauthorized equipment modifications will void all warranties.  
Test the ON/OFF switch before operating.The purpose of the  
switch is to shut down the engine.  
NEVER transport the saw with the blade mounted.  
PAGE 10 — MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #0 (07/15/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FS3SP CONCRETE SAW — RULES FOR SAFE OPERATION  
Emergencies  
ALWAYS know the location of the nearest fire extinguisher  
■
and first aid kit. Know the location of the nearest telephone.  
Also know the phone numbers of the nearest ambulance,  
doctor and fire department. This information will be  
invaluable in the case of an emergency.  
Maintenance Safety  
■
NEVER lubricate components or attempt service on a running  
machine.  
■
ALWAYS allow the machine a proper amount of time to cool  
before servicing.  
■
■
Keep the machinery in proper running condition.  
Fix damage to the machine immediately and always replace  
broken parts.  
■
■
Dispose of hazardous waste properly.Examples of potentially  
hazardous waste are used motor oil, fuel and fuel filters.  
DO NOT use food or plastic containers to dispose of  
hazardous waste.  
MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #0 (07/15/02) — PAGE 11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FS3SP CONCRETE SAW — DIMENSIONS  
Figure 2. FS3SP Concrete Saw Dimensions  
TABLE 1. DIMENSIONS  
REFERENCE  
LETTER  
A
DESCRIPTION  
DIMENSION (MM)  
45" (1143)  
43" (1092)  
92" (2337)  
73" (1854)  
67" (1701)  
28" (711)  
Max Height (Handle Bars Fully Raised)  
B
C
D
E
F
G
H
I
Max Height (Handle Bars Fully Lowered)  
Max Length (Handle Bars Fully Raised & Front Pointer Lowered)  
Max Length (Handle Bars Fully Raised & Front Pointer Raised)  
Max Length (Handle Bars Fully Lowered & Front Pointer Raised)  
Max Handle Bar Width  
Max Handle Bar Deflection  
12" (305)  
Front Wheel Base  
18" (457)  
Rear Wheel Base  
20" (508)  
J
Max Width  
28" (711)  
Crated Dimension (L x W x H) 47" (1194) x 30" (762) x 44" (1118)  
PAGE 12 — MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #0 (07/15/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FS3SP CONCRETE SAW — WEIGHTS  
Figure 3. FS3SP Concrete SawWeights  
TABLE 2. WEIGHTS  
OPERATING WEIGHT  
Lbs. (kgs)  
SAW  
DESCRIPTION  
FS3SP-20KE14 Saw, 14", Self Prop, 20 HP Kohler, Elec. Start  
FS3SP-20KE20 Saw, 20", Self Prop, 20 HP Kohler, Elec. Start  
FS3SP-20HE14 Saw, 14", Self Prop, 20 HP Honda, Elec. Start  
FS3SP-20HE20 Saw, 20", Self Prop, 20 HP Honda, Elec. Start  
550(249)  
555 (252)  
550 (249)  
555 (252)  
Crated Weight (kgs) 600 lbs (272)  
MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #0 (07/15/02) — PAGE 13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FS3SP CONCRETE SAW — MAJOR COMPONENTS  
BASIC COMPONENTS  
24  
19  
17  
18  
8
1
15  
5
3
16  
20  
23  
13  
4
21  
7
2
11  
10  
25  
6
9
12  
Figure 4. FS3SP Concrete Saw Basic Components  
PAGE 14 — MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #0 (07/15/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FS3SP CONCRETE SAW — MAJOR COMPONENTS  
BASIC UNIT, FS3 ASSY.  
NO.  
1
2
3
4
5
6
7
8
PART NO.  
15072  
15200  
15399  
15468  
15523  
15573  
15602  
15604  
15605  
15606  
15670  
15674  
15731  
15739  
15764  
15776  
15779  
15780  
15781  
15830  
15904  
25252  
15569  
15750  
15652  
PART NAME  
QTY.  
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
REMARKS  
HANDLE, CLAMPING  
See Page 54  
See Page 54  
See Page 50  
See Page 54  
See Page 50  
See Page 46  
See Page 54  
See Page 50  
See Page 44  
See Page 68  
See Page 50  
See Page 42  
See Page 48  
Not Shown  
CHASSIS ASSEMBLY  
COVER, CHAIN ASSEMBLY  
GROMMET, 1.0 X .13 X 1.375  
TOOL KIT  
SHAFT, BLADE ASSEMBLY  
COVER, ASSEMBLY, REAR  
COVER, BELT ASSEMBLY  
AXLE, SP REAR ASSEMBLY  
DRIVE ASSEMBLY, FS3  
COVER, BLADE FLANGE ASSEMBLY  
UNDERCARRIAGE, ASSEMBLY  
MOUNT, ENGINE ASSEMBLY  
FS3, DECAL KIT  
FS3, WATER ASSEMBLY  
HYDROSTATIC THROTTLE ASSEMBLY  
HANDLEBAR ASSEMBLY, LEFT  
HANDLEBAR ASSEMBLY, RIGHT  
FS3, LIFTING BALE KIT  
SASH ASSEMBLY, FS3  
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
See Page 52  
See Page 70  
See Page 54  
See Page 54  
See Page 54  
See Page 50  
See Page 50  
Not Shown  
POINTER, FRONT ASSEMBLY  
KIT, SHIPPING  
MANUAL RAISE/LOWER ASSEMBLY  
ENGINE ASSEMBLY  
See Page 58  
See Page 72  
See page 56  
BLADE GUARD ASSEMBLY  
1
MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #0 (07/15/02) — PAGE 15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FS3SP CONCRETE SAW — CONSOLE COMPONENTS  
8.  
Pump On Switch – On position provides power to external  
water pump. Off position secures power to external water  
pump.  
Figure 5 displays the location of the various operational control  
features of the FS3SP saw. Features are dependent on the specific  
model saw selected. The function of each console component or  
indicator is explained below:  
9.  
Raise/Lower Crank Handle – IPhysically orients  
saw(Raises/Lowers) depending on turn direction and  
number of turns. Turning the handle "clockwise" lowers the  
saw, turning the handle "counter-clockwise" raises the saw.  
(Used in conjunction with the Depth Feed Gauge)  
1.  
Engine ON/OFF Switch – Pull the switch to permit engine  
starting. Push the switch to stop engine. Also acts as a fast  
and secure way to stop the engine in an emergency.  
2.  
3.  
Digital Tachometer/Hourmeter – Indicates engine RPM  
10. Depth Feed Gauge –Indicates the blade cutting depth in  
inches. To activate, first lower the blade via the crank  
handle until the blade touches the cutting surface. Then  
roll the depth feed dial until the face label reads zero.  
and operation hours saw has been in use.  
Water ON/OFF Valve – On position opens valve and  
permits water to flow from source through saw water hose.  
OFF position closes valve and halts the flow of water  
through the saw.  
11. Start Button – A spring loaded button, that when pressed  
actuates the engine start solenoid.  
4.  
5.  
Throttle Lever – Pull the lever to increase engine RPM.  
Push lever to decrease engine RPM (twist handle to lock).  
12. Forward/Reverse Speed Lever – Controls forward and  
reverse speeds for self-propelled operation. Provides  
positive neutral for engine start. ALWAYS place  
transmission engage/disengage lever in the engage  
position before setting speed lever.  
Choke Lever – Pull lever to assist when starting a cold  
engine. Push lever down after engine warms to disengage  
choke.  
6.  
7.  
Blade Raise/lower Switch – Raise position raises blade.  
13. Handle Bar Locking Knobs – Loosen or tighten these  
two knobs when making adjustments to the handlebar(s).  
Turn handle(s) counter-clockwise to loosen and  
clockwise to tighten.  
Lower position lowers blade.  
Light Switch – On position provdes power to external  
lights. Off position secures power to external lights.  
Figure 5. Console Components  
PAGE 16 — MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #0 (07/15/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FS3SP CONCRETE SAW — BASIC ENGINE COMPONENTS  
Figure 6. Engine Controls and Components  
WARNING  
INITIAL SERVICING  
The engine (Figure 6) must be checked for proper lubrication and  
filled with fuel prior to operation. Refer to the manufacturers Engine  
manual for instructions & details of operation and servicing.  
Adding fuel to the tank should be accomplished  
only when the engine is stopped and has had an  
opportunity to cool down. In the event of a fuel  
spill, DO NOT attempt to start the engine until the fuel residue  
has been completely wiped up, and the area surrounding the  
engine is dry.  
1.  
Air Filter – A dirty air filter will restrict airflow to the  
carburetor, reducing engine performance.When the engine  
is operated in very dusty conditions, clean the air filter more  
often than specified in the Maintenance Schedule.  
3. Oil Filler Cap –Check the engine oil level with the engine  
stopped and in a level position. Oil is a major factor affecting  
engine performance and service life. Use 4-stroke  
automotive detergent oil.  
NOTE  
Operating the engine without an air filter,  
with a damaged air filter, or a filter in need of  
replacement will allow dirt to enter the  
engine, causing rapid engine wear.  
SAE 10W-30 is recommended for general use. Refer to  
manufacturers Engine Manual for further data regarding  
other viscositiies/temperature limits.  
To Change/Clean Air Filter  
ENGINE OIL REFILL CAPABILITIES:  
■
Remove Air Filter Wing Nut and pull the Air Filter  
■
Without Oil Filter Replacement:  
1.27 qt. (1.20 L)  
Element out of the filter housing  
■
Replace, or clean by using low pressure compressed  
(30 psi MAX) from inside out.  
■
With Oil Filter Replacement:  
1.59 qt. (1.20 L)  
NOTICE  
2. Fuel Filler Cap – Remove this cap to add unleaded  
gasoline (86 Octane rating or higher) to the fuel tank. Make  
sure cap is tightened securely. The engine fuel tank holds  
approximately 2 gallons of gasoline. DO NOT over fill.  
Running the engine with a low oil level can cause  
engine damage. The oil alert system will automatically  
stop the engine before the oil level falls below safe limits;  
however, it is advisable to always check the engine oil  
level before startup.  
MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #0 (07/15/02) — PAGE 17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FS3SP CONCRETE SAW — ENGINE COMPONENTS  
Figure 7. Engine Controls and Components  
4. Engine Oil – (See figure 7)  
5. Electric Starter – Engine Start is electrically actuated by  
12Volt DC system.Starter button, choke,Throttle Handle,  
and Engine On/Off Switches are conveniently located  
on the operating console. (See figure 5)  
A. Engine Oil Dip Stick  
■
Remove the dipstick and wipe clean.  
Fully insert the dipstick; Then remove it to check  
the oil level.  
B. Engine Oil Limits  
■
6. Oil Filter – A "Spin On/Off" type oil filter is utilized. It is  
recommended that the filter be replaced every (year / or  
200 hours of operation). Oil Filter tightening torque is  
approximately 16 ft-lb. (22 N-m, 2.2 kg-m)  
■
Check Oil Level. If the level is low, fill to the upper  
limit mark on the dipstick with the recommended  
oil.  
NOTICE  
■
Reinstall the dipstick and screw the oil filter cap  
securely.  
Use only genuine Honda filters or a filter of equivalent  
quality which is specified by the engine model. Using the  
wrong filter, or a non-Honda quality equivalent, may  
cause engine damage.  
C. Engine Oil Filler and Cap.  
Ensure that the mouth of the oil filler is kept clean  
and that the cap is secure after servicing.  
D. Engine Drain Bolt.  
7. Muffler – A high-mount muffler (type "8") is utilized to  
reduce noise and emissions; as well as deflect engine  
exhaust away from the operator.  
■
Drain the used oil while the engine is still warm.  
Place suitable container to catch the used oil  
before removing the Engine Drain Bolt.  
■
■
Allow used oil to drain completely and then  
reinstall oil drain bolt and tightly secure.  
WARNING  
Engine components can generate extreme  
heat. To prevent burns, do not touch these  
areas while the engine is running or  
immediately after operations. Never operate  
the engine with the muffler removed.  
Refer to "A. & B." above for Oil Refil.  
NOTICE  
Dispose of used motor oil in a manner that is  
compatible with the environment and the Local,  
State, & Federal laws.  
PAGE 18 — MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #0 (07/15/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FS3SP CONCRETE SAW — GENERAL INFORMATION  
Operator control of the saw is safely accomplished with adjustable  
ergonomic handle bars, and a combination of conveniently oriented  
items on the console such as: Raise/Lower Crank Handle,  
Tachometer/Hourmeter, ON/OFFWaterValve, Depth Feed Gauge,  
and Emergency Engine ON/OFF switch.Additionally, the console  
also provides starting, power control and forward/reverse controls.  
FAMILIARIZATION  
The MQ Whiteman FS3SP Series concrete saws are designed for  
wet or dry cutting utilizing diamond blades. They are self-propelled  
via a hydrostatic transmission system and have been engineered  
for general, industrial and high production flat sawing applications.  
The exceptional performance of these saws centers around  
innovativefeatures, topqualitycomponents, andcommittedattention  
to state-of-the-art manufacturing.  
All MQWhiteman FS3SP saws are designed,engineered and  
manufactured with strict adherence to American National  
Standards Institute, Inc. (ANSI) guidelines B7.1 and B7.5.  
The reinforced heavy gauge steel frame and chassis assembly has  
been precisely jig welded to eliminate operational bending and/or  
flex that would lead to diminished blade performance. Additionally,  
the general weight-to-strength ratio design of the frame and chassis  
assembly provides for optimum weight distribution to keep the blade  
running true in the cut.  
POWER PLANTS  
The FS3SP Series saws provides a variety of gasoline engine  
choices (Table 3). Selection of a specific engine, and its capacity  
measured in horsepower/torque, directly affects the performance of  
the diamond blade.  
An innovative outboard blade shaft bearing assembly ensures  
minimalflutterandshaftharmonicsprovidingthemostadvantageous  
condition for a diamond blade at operating speeds. Also, this design  
further promotes greater operating life to the blade shaft bearings  
andV-Belts.  
The FS3SP series saws are generally classified in the industry as  
a "MEDIUM " horsepower saw. This classification is particularly  
useful when selecting the proper diamond blade for an application.  
Refer to the engine Owner's Manual for specific instructions  
regarding engine operation and maintenance practices.  
Heavy duty front and rear axles, oversized reinforced wheels  
supported by roller wheel bearings and locking collars, and industrial  
under carriage assemly ensure accurate tracking and years of  
reliable use.The positive locking Raise/Lower screw feed system  
with accurate depth gauge easily orients blade elevation, and will  
not permit blade creep during cutting operations.  
Arobustwaterplumbingsystemallowsforoptimumflutedfloodwater  
to the blade for wet cutting applications .  
TABLE 3. POWER PLANTS  
FUEL TANK  
GAL. (Liters)  
ENGINE MFR.  
HP  
STARTING SYSTEM  
AIR CLEANER  
HONDA  
20  
20  
Electric  
Electric  
Ind. Dry Canister  
Ind. Dry Canister  
1.6 (6.1)  
1.6 (6.1)  
KOHLER  
MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #0 (07/15/02) — PAGE 19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FS3SP CONCRETE SAW — GENERAL INFORMATION  
WATER SYSTEM  
UNDER CARRIAGE SYSTEM  
All FS3 saws provide a water direction system to provide cooling  
water to the diamond blade. This system consist of : a standard  
"garden hose" valve that connects the water source (via hose) to the  
saw, an ON/OFF console water switch, water hose with quick  
disconnect manifold fittings, and a 14" or 20" blade guard.  
A jig welded heavy steel gauge under carriage assembly supports  
the saw in tracking, pivoting and stabilization. A 1" diameter rear  
axle supports two solid rubber (10" x 2.75") cast hub wheels with  
roller bearings, grease fittings and locking collars. A 5/8" diameter  
front axle supports two solid rubber (5" x 2") cast hub wheels with  
roller bearings, grease fittings and locking collars. The assembly  
pivots about two rocker blocks with bushings. See page 42.  
CONSOLE  
An ergonomically designed control console allows the operator to  
easily understand and/or operate the adjustable handlebars, Raise/  
Lower Crank Handle, Tachometer/Hourmeter, ON/OFF Water  
Valve, Depth Feed Gauge, and Emergency Engine ON/OFF Switch.  
Additionally, for electric start and self-propelled models, the console  
also provides starting, power control and forward/reverse controls.  
BLADE DRIVE SYSTEM  
An innovative blade shaft assembly has been specifically designed  
to support the optimum distribution of torque from the engine shaft to  
the blade shaft, and to ensure minimal vibratory conditions on the  
tips of the shaft.  
MECHANICAL RAISE/LOWER SYSTEM  
Balanced engine & blade shaft pulleys are connected to their  
respective shafts, and four 3VX V-belts connect the engine pulley to  
the blade shaft pulley. The 1- 1/4" diameter blade shaft is supported  
bytwoself-aligningpillowblockbearingsthatareuniquelypositioned  
on the most outboard portion of the reinforced frame.  
A positive locking mechanical raise and lower screw feed assembly  
supports elevation cycling operations. A crank raise/lower handle  
islocatedontheconsolewith"clockwise"rotationprovidinglowering  
action, and "counter-clockwise" rotation providing raising action.  
An ACME precision screw and thread assembly provide accurate  
travel; while a spring loaded plunge ball system ensures positive  
height position locking.  
The combination of pulley and blade shaft bearing positioning  
ensures minimal vibration & flutter to the ends of the blade shaft.  
The blade drive system has been designed for left and right hand  
cutting. See page 46.  
An adjustable depth gauge assembly is synchronized with raise/  
lower handle rotations to accurately depict depth feed.SeeTable 4  
for blade selection with respect to depth of cut. Blade orientation is  
referenced on the console's depth feed gauge.  
BLADE GUARD ASSEMBLY  
The FS3SP offers a 14" or a 20" hinged two-piece, heavy steel  
gauge blade guard.  
Both blade guards provide zinc plated, fluted floodwater manifold  
assemblies that supply optimum volume and dispersal of water to  
both sides of the diamond blade for wet cutting.The sizable (6")  
fluted floodwater tubes resist clogging and are easily removed for  
maintenance.  
The spray pattern and orientation, in conjunction with the design of  
thebladeguard, providesexceptionaldustsuppressionwhencutting  
dry, and may also be desired when the job site requires minimal use  
ofwater.  
TABLE 4. BLADE SELECTION  
Diamond Blade  
Diameter (In.)  
Depth of Cut  
A quick disconnect hose and blade guard are easily removed for  
fast blade changes, and easily seats itself on the chassis bayonet  
fitting. The blade guard may be oriented for left or right hand cutting.  
See pages 56.  
12"  
14"  
16"  
18"  
20"  
3-5/8"  
4-5/8"  
5-5/8"  
6-5/8"  
7-5/8"  
PAGE 20 — MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #0 (07/15/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FS3SP CONCRETE SAW — INSPECTION  
Before Starting  
NOTE  
1. Read safety instructions at the beginning of manual.  
FS3SP Series concrete saws have an oil  
Alert System. This system will  
automatically stop the engine in the event  
of low oil level. ALWAYS be sure to check  
the engine oil level prior to starting the  
engine.  
2. Clean the SAW, removing dirt and dust, particularly the  
engine cooling air inlet, carburetor and air cleaner.  
3. Check theairfilterfor dirtanddust. Ifairfilterisdirty,replace  
air filter with a new one as required.  
4. Check carburetor for external dirt and dust. Clean with dry  
compressedair.  
Table 5. Oil Type  
5. Checkfasteningnutsandboltsfortightness.  
Season  
Temperature  
25°C or Higher  
25°C~10°C  
Oil Type  
Summer  
Spring/Fall  
Winter  
SAE 10W-30  
SAE 10W-30/20  
SAE 10W-10  
Engine Oil Check  
1. To check the engine oil level, place the saw on secure level  
ground with the engine stopped, and the diamond blade  
removed.  
0°C or Lower  
2. Removethedipstickfromtheengineoilfillerhole(Figure8)  
and wipe it clean.  
Explosive Fuel  
C
1. Remove the gasoline cap located on top of fuel tank.  
UPPER  
LIMIT  
2. Visuallyinspecttoseeiffuellevelislow. Iffuelislow,replenish  
with unleaded fuel.  
B
3. When refueling, be sure to use a strainer for filtration. DO  
NOT top-off fuel. Wipe up any spilled fuel.  
LOWER  
LIMIT  
A
D
Figure 8. Engine Oil Service  
3. Insertandremovethedipstickwithoutscrewingitintothefiller  
neck. Check the oil level shown on the dipstick.  
4. If the oil level is low (Figure 8), fill to the edge of the oil filler  
holewiththerecommendedoiltype(Table5).Maximum oil  
capacity is 400 cc.  
NOTE  
Reference manufacturer engine manual for  
specific servicing instructions.  
MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #0 (07/15/02) — PAGE 21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FS3SP CONCRETE SAW — INSPECTION  
HydrostaticTransmission - An EATON® Model 7 hydrostatic  
Battery - The 12-Volt DC battery (figure 11) is shipped dry, and  
will require a proper electrolyte level for operation(electric start  
models only).  
transmission (Figure 9) provides the power for the saw's  
propulsion system.The transmission drives a sprocket that directly  
connects the rear axle assembly via a drive chain.The "no load"  
forward/reverse speeds are approximately 80 ft/min  
HYDROSTATIC  
TRANSMISSION  
PUMP  
O
T
H
O
IL  
L
E
VE  
L
O
IL  
L
E
VEL COLD  
DRIVE CHAIN  
Figure 11. Battery  
REAR  
AXLE  
When servicing of the batter is required perform the following:  
■
■
■
A face shield and rubber gloves should be worn while  
handleing and servicing battery's electrolyte.  
SPROCKET  
Figure 9. HydrostaticTransmission  
Disconnect battery terminal clamps, and remove the  
battery from the saw when servicing is required.  
1.The transmissioni is factory filled with approved fluid that has  
a viscocity equivalent to SAE 20 W 20. SHould additional  
servicing be required, the following oils are recommended:  
DO NOT overfill the battery.  
WARNING  
General Motors Dextron B  
Ford MM2C-33F  
Electrolyte is an acid and must be handled  
with caution. Servicing instructions from the  
electorlyte manufacturer must always be  
followed to ensure saftey. Serious injury can  
result from careless handling and non-  
compliance to saftey handling instructions.  
Ford M2C-41A  
International Harvester Hy-Tran Fluids  
WARNING  
Overfilling the battery may cause the electrolyte to overflow  
resulting in corrosion to nearby components. Immediately wash  
off any spilled electrolyte(battery acid).  
Additionally, when connecting the positive  
(+) cable to the battery's positive (+)  
terminal post, DO NOT allow contact of  
the wrench or any metallic part to come in  
contact with the battery's negative (-)  
terminal post. This may result in an  
exlectrical short circuit or an explosion  
Figure 10.Transmission Reservoir  
NOTICE  
DO NOT overfill the expansion tank. (See figure 10). Note the  
level marks on the oil reservoir. It is essential to reference the  
existing oil conditions (A) "cold" or (B) "hot" levels piror to  
servicing. Overfilling the transmission with oil may cause the  
seals to rupture, causing mechanical damage.  
NOTICE  
Use only distilled water in the battery.Tap water can reduce the  
operating life of the battery.  
PAGE 22 — MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #0 (07/15/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FS3SP CONCRETE SAW — INSPECTION -BLADE  
4.  
Directional Arrow – Check to ensure that the blade is  
oriented properly on the blade shaft for sawing. Reference  
the directional arrow in the blade and place it so the direction  
of rotation “downcuts” with the turn of the shaft.  
WARNING  
Failure to thoroughly inspect the diamond blade (Figure 12) for  
operational safety could result in damage to the blade, the saw,  
and may cause injury to the user or others in the operating area.  
5.  
Diamond Segment or Rim – Ensure there are no cracks,  
dings, or missing portions of the diamond segment/rim. DO  
NOT use a blade that is missing a segment or a portion  
of the rim. Damaged and/or missing segments/rims may  
cause damage to your saw, and injury to the user or others  
in the operating area.  
6.  
7.  
Specifications – Ensure that the blade specifications, size,  
and diameter properly match up to the sawing operation.  
Wet blades must have water to act as a coolant. Utilizing a  
diamond blade not matched properly to the task may result  
in poor performance and/or blade damage.  
Arbor Hole – It is essential that the arbor hole diameter  
properly matches the blade, and that it is free from  
distortions. Correct blade flanges (collars) must be used.  
The inside face of the flanges must be clean & free of debris.  
An out of round arbor condition will cause damage to the  
blade and the saw.  
8.  
MAX RPM – This RPM reference is the maximum safe  
operating speed for the blade selected. NEVER exceed  
the max RPM on the diamond blade. Exceeding the MAX  
RPM is dangerous, and may cause poor performance and  
may damage the blade.  
Figure 12. Diamond Blade  
1. Drive Pin Hole – A commonly located hole on the diamond  
blade core that prevents operational blade slippage  
between the inner & outer blade flanges (collars). Inspect  
the diameter of the hole to ensure there is no distortion,  
and that a snug fit develops between the hole and drive  
pin.  
2.  
Stress Relief Holes (Gullets) – Check the steel core for  
cracks that may have propagated from the slots and/or  
gullets. Cracks indicate extreme fatigue failure and if sawing  
continues, catastrophic failure will occur.  
3.  
Edge Of The Steel Core – Check the diameter edge for  
discoloration (blue oxidation) indicating an overheating  
condition caused by insufficient cooling water/air.  
Overheating of blades may lead to loss of core tension  
and/or increase the possibility for blade failure. Check to  
make sure the steel core’s width is uniform about the rim of  
the blade, and not succumbing to an “under cutting”  
condition brought about by highly abrasive material or  
improper under cutting core protection.  
MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #0 (07/15/02) — PAGE 23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FS3SP CONCRETE SAW — INSPECTION -BLADE PLACEMENT  
NOTE  
3.  
Blade NutWrench – Remove the blade nut wrench (3) fro  
the tool holder and unscrew the blade shaft nut (right-side).  
This nut loosens clockwise and tightens counter-  
clockwise.  
The following steps should be accomplished  
before placing the diamond blade on the  
blade shaft.  
4.  
5.  
Blade Nut – Remove the blade nut (4). For reassembly,  
DO NOT over tighten the blade nut against the outer flange.  
Tighten blade nut approximately 45-50 ft-lbs/62-69 N/m.  
Outside Blade Flange (Collar) – Ensure that the flange  
face is clean and free of debris and is placed flush against  
the diamond blade (7). Check that the drive pin goes through  
the blade pin hole (6) and seats properly into the inner  
flange (8).  
■
■
Place the console ON/OFF button in the OFF position.  
Raise the saw to a high position by cranking the Raise/Lower  
handle in a counterclockwise direction.  
■
Use the Blade Nut Wrench & Blade Shaft Locking Wrench  
stored in the lower section of the console to install the diamond  
blade.  
6.  
7.  
Blade Pin Hole – Align this hole with the drive pin hole on  
the inner flange collar.  
Diamond Blade – Ensure that the proper blade has been  
selected for the job. Pay close attention to the directional  
arrow on the blade, clockwise for right-side cutting,  
counter-clockwise for left-side cutting. The arbor hole  
of the blade must match the 1" arbor of the blade shaft.  
■
Reference Figure 13 (Diamond Blade Placement) when  
removing or installing the diamond blade.  
1.  
Belt Guard – Unscrew the guard security knob and water  
hose quick disconnect fitting and remove blade guard (1)  
from its bayonet fitting and set it beside the saw.  
8.  
Inner Flange Collar – This flange is fixed upon the blade  
shaft, and is manufactured with a drive pin hole.The inside  
surface of the flange must be free of debris and permit a  
tight closure on the surface of the blade.  
2.  
Shaft Lock Tool – Remove the shaft lock tool (2) from  
the tool holder and insert the pointed end through the front  
of the saw frame into the machined hole in the blade shaft.  
A conveniently placed opening on the front of the saw frame  
permits the use of the shaft lock tool. This tool inhibits the  
shaft from rotating when applying torque to the blade nut.  
Figure 13. Diamond Blade Placement  
PAGE 24 — MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #0 (07/15/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FS3SP CONCRETE SAW — INSPECTION -GUARDS, COVERS & BELTS  
Guards and Covers Check  
V-Belts and Covers  
CAUTION:  
WARNING  
NEVER attempt to check the V-belt with the engine running  
because severe injury can occur. Keep fingers, hands, hair and  
clothing away from all moving parts.  
NEVER operate the saw without blade guards and covers  
(Figures 14 and 15) in place. DO NOT operate with the front of  
the blade guard raised. The blade exposure cannot exceed 180  
degrees during operations. Adhere to the safety guidelines of  
the American National Standards Institute (ANSI) B7.1 and  
B7.5.  
V-belts Alignment andTensioning  
This concrete saw is equipped with four premium V-belts that  
have been aligned and tensioned by factory personnel. All four  
V-belts MUST be installed for proper operation of the saw.Failure  
to run the saw with less than four belts may damage the saw or  
equipment.  
Use the following procedure to check the alignment of V-belts:  
1. RemovetheboltsthatsecuretheV-beltcover(Figure16)to  
thesawframe.  
Figure 14. Blade Guard  
CHECK the following on the "blade guard":  
■
■
■
Check to ensure the capacity of the blade guard matches the  
diameter of your diamond blade.  
Check that the guard seats firmly upon the bayonet fitting of  
the saw frame.  
Check that the spring tensioned front cover of the guard is  
firmly seated with the rear section of the guard, and there are  
no gaps.  
■
■
Check the fit of the water hoses about the two water manifolds  
(14" guard). NEVER lift the blade guard while cutting.  
Figure 16. V-Belt Cover  
2. Check uniform parallelism (Figure 17) of V-belts and pulley  
Check that the flood water tubes and water jets are clear and  
open. Test the water supply for pressure and flow (to both  
sides of the blade) before sawing operations.  
(sheaves).Useastraightedgeormachinists'ssquareagainst  
both pulleys and adjust both pulleys until equally aligned.  
CHECK the following on the "blade flange cover":  
■
Check that the flange cover seats firmly upon the bayonet  
fitting of the saw frame prior to operation.  
■
This flange cover is to be in place when cutting from either the  
right or left side of the saw.  
Figure 15. Blade Flange Cover  
Figure 17.V-Belt Parallelism  
MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #0 (07/15/02) — PAGE 25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3. Check V-belt tension (Figure 18) by using a tensionmeter  
(6.0 - 9.0 lbs.) against the inside belt at a mid point between  
the two pulleys, or by deflecting the center belt at a mid point  
3/8” (10 mm) - 1/2” (13 mm).  
5. IftheV-beltsbecomeswornorloose,replacethembyusing  
the following V-belt part numbers listed in Table 6.  
Table 6. V-Belts and Pulleys  
CORRECT V-BELT  
TENSION 3/8 IN. (10 MM) TO  
1/2 IN.(13 MM) WHEN  
DEPRESSED AT MIDPOINT  
AS SHOWN  
Engine Size  
V-Belt P/N  
Pulley P/N  
Blade Size  
3VX375  
10799  
15365  
14"  
20 HP Engine  
3VX355  
15897  
15366  
20"  
Figure 18.V-BeltTension  
4. DO NOT over or under tension the V-belts. Severe damage  
can occur to the saw and engine crank shaft if the belts are  
over tensioned. A decrease of power to the blade and poor  
performance will result if the belts are under tensioned (loose  
on pulleys).  
PAGE 26 — MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #0 (07/15/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FS3SP CONCRETE SAW— INITIAL START-UP  
CAUTION:  
NOTE  
DO NOT attempt to operate the saw untiDl the  
The CLOSED position of the choke lever enriches  
the fuel mixture for starting a COLD engine.The  
OPEN position provides the correct fuel mixture  
for normal operation after starting, and for  
restarting a warm engine.  
Safety, General Information and Inspection  
sections have been read and understood.  
Depending on engine manufacturer, operating  
steps may vary. See engine manufactures  
operating manual. The following start-up procedure makes  
reference to a HONDA 20 HP Engine.  
5. Pull the Choke Knob (Figure 21) up into the "OPEN"  
1. Ensure the diamond blade has been mounted correctly and  
that it raised above the surface you about to saw.  
position  
2. Connect a hose (water source) to the water input port of the  
saw (see page 50, item 2, Water System Assembly), and  
test for adequate flood water [ 4 to 5 gallons per minute (15  
to 19 LT/min)].  
3. Set the Speed Control Lever(Figure 19) to the start  
position(neutral)andholdleveragainstthestartmicroswitch.  
Figure 21. Choke Knob  
CAUTION:  
Figure 19. Speed Control Lever  
4. PULL the Console Engine ON/OFF switch (Figure 20) to  
.
The engine governor speed has been set at the factory. Changing  
the governor speed could damage the blade and/or the saw.  
the"PULL-ON"position.  
6. Place the throttle lever (Figure 22) halfway between fast  
and slow for starting. All sawing is done at full throttle. The  
engine governor speed is factory set to ensure optimum  
blade operating speeds.  
Figure 20 Console Engine ON/Off Switch  
Figure 22.Throttle Lever  
MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #0 (07/15/02) — PAGE 27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FS3SP CONCRETE SAW — INITIAL START-UP  
7. Push the Start Switch(Figure 23) to start the engine  
Maneuvering The Saw  
WARNING  
The blade is spinning whenever the engine is running.  
Raise the blade high above the surface when maneuvering the  
saw. Damage to the blade and/or saw may occur if the blade  
strikes the pavement.  
CAUTION:  
Figure 23. Start Switch  
z
NEVER stop the engine in the cut while  
working at high speeds, except for  
extreme emergencies.  
8. If the engine has started, slowly return the choke lever  
(Figure 23) to the CLOSED position. If the engine has not  
started repeat steps 1 through 5.  
9. Before the saw is placed into operation, run the engine for  
several minutes. Check for fuel leaks, and noises that would  
associate with a loose guard and/or covers.  
10. All sawing is done at full throttle. Your engine governor has  
been set at the factory to ensure an optimum speed setting.  
Stopping the Engine  
NEVER stop the engine while the blade is in the cut, except for  
extreme emergencies. A sudden stoppage of the engine at high  
speed while in a cut could damage the blade and/or saw, and  
may cause injury to the user or other in the operating area.  
1. Place the throttle lever (Figure 22) in the slow position, and  
listen for the engine speed to decrease.  
2. Push the console engine ON/OFF switch (Figure 20) to the  
“OFF” position.  
PAGE 28 — MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #0 (07/15/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FS3SP CONCRETE SAW — OPERATION  
Saw Alignment  
CAUTION:  
1. The FS3SP employs a front and rear pointer (Figure 24) that  
has been precisely aligned with the diamond blade at the  
factory. Referencing the figure below, accurate tracking is  
accomplished by referencing the front and rear pointer tips  
over the cut line. Precise saw direction is accomplished by  
slight operator pressure against the handle bars.  
ALWAYS saw in a straight line only. Serious  
damage to the blade may occur if the saw is  
twisted or forced to cut radius shapes.  
6. Slowlylowerthediamondbladeontothecutlinebycranking  
theRaise/Lowerhandleclockwise. Whentheblade“touches”  
thecuttingsurface,“zero-out”thedepthfeedgauge (Figure  
5,item10)byrollingthedepthwheeluntil“0”islinedupwith  
theslipmark. Slowlycontinuetolowerthebladeintothecut  
until the desired depth is achieved.  
If the water supply to your blade is interrupted - STOP  
sawing immediately.  
7. Set the sawing depth and saw only as job conditions and  
specificationsrequire. Deepsawingiswastefultothelifeof  
the blade. The preferred method of sawing is to “step cut”  
in increments of 2” (51 mm). Step cutting provides the  
optimum opportunity for the blade to cut fast and last it’s  
longest.  
Figure 24. Saw Pointers (Front/Rear)  
2. To reorient a pointer position, loosen the screw that secures  
thepointerbartotheshaft, adjustasnecessary, andretighten  
the screw.  
8. The rotation of the blade creates a tendency for the saw to  
slightlypullinaparticulardirection.Toensureastraightline  
ofsawing,applypressureagainsttheappropriatehandlebar  
asyouslowlyadvancethesawforward. DONOTforcethe  
bladeintothecutanyfasterthanitsdesignedtendency  
is effective cut and remove the material.  
3. For operator comfort, ergonomically designed handle bars  
adjust by loosening two clamping knobs (Figure 5, item 14),  
and adjusts to the desired height. Tighten the knobs back  
down when the desired height has been achieved.  
Wet Saw Operation  
WARNING  
The operator must wear the appropriate protective  
equipment and clothing while engaged in sawing.  
For wet sawing :  
1. Connecthosefromwatersourcetothehosefittingconnec-  
tion(seepage 52,item 1, WaterSystemAssembly)ofthe  
saw. The source pressure should be approximately 30-40  
psi.  
2. Ensurethequickdisconnectwaterthosefittingisconnected  
to the Floodwater manifold of the blade guard.  
3. Turn water source on.  
4. Select the “ON” position (water valve on the saw console),  
andensurethe properflowandrate(4-6gallons/minute)is  
equally directed to both sides of the diamond blade.  
5. Align the saw along the cut line utilizing the front and rear  
pointers.  
MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #0 (07/15/02) — PAGE 29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FS3SP CONCRETE SAW — OPERATION  
WARNING  
WARNING  
Engine components can generate extreme  
heat.  
If the engine stalls for any reason during  
sawing, raise the blade out of the cut  
before restarting.  
Diamond Blades and Blade Speed  
10. The operator must recognize and adhere to the optimum  
speed that the saw advances while sawing. DO NOT force  
the saw in the cut. Observe the engine tachometer from time  
to time to get the feel for a smooth sawing pace relative to  
RPM.  
1. Diamond sawing consist of cutting WET (using water to cool  
the blade) or DRY (using the circulating air to cool the blade).  
2. Selecting the diamond blade type and grade defines how  
the blade will perform both in cutting speed and blade life.  
11. Factors for sawing economy:  
MULTIQUIP offers a full line of quality diamond blades  
to match up with your FS3SP, that provide the highest  
level of sawing value and performance  
z
z
z
z
z
Type of Blade  
Depth of Cut  
Sawing Speed  
Characteristics of the Material Being Cut  
Wet or Dry Sawing  
Blade Speed  
1. A diamond blade’s performance is directly connected to  
specific peripheral (rim) speeds.  
Finishing A Cut  
1. Raise the blade out of the cut by cranking the Raise/Lower  
handlecounter-clockwise(Figure5,item10).Raisetheblade  
2. The following shaft rotational speeds have been factory set  
to ensure optimum blade performance.  
high enough out of the cut to clear the surface and allow the  
saw to be maneuvered.  
z
z
FS3SP 14” Capacity-3,200 RPM.  
FS3SP 20” Capacity-2,600 RPM.  
2. Move the engine throttle lever to the idle (SLOW) position  
(Figure 22).  
3. Push the console engine ON/OFF button to the “OFF”  
WARNING  
position (Figure 5, item 1).  
Operating saw blades at rotational speeds  
greater than those specified by the manufac-  
ture can cause blade damage, and may in-  
jure the user or others in the operating area.  
4. Set the engine ON/OFF switch to the “OFF” position  
(Figure 6, item 3).  
5. Place the water valve (Figure 5, item 3) in the “OFF” position  
(as required).  
PAGE 30 — MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #0 (07/15/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FS3SP CONCRETE SAW — MAINTENANCE  
4. ENGINE AIR FILTER: Clean air filter 2 TO 3 times daily  
CAUTION:  
when DRY cutting.See Engine Owner’s Manual for detailed  
General maintenance practices are crucial to  
information.  
the performance and longevity of your saw.The  
extreme environments of sawing operations  
require routine cleaning, lubrication, belt  
tensioning, and inspection for wear and dam-  
age  
5. ENGINE TANK & STRAINER: Clean every year/ or 300  
hours.  
6. FUEL LINE:Replace every two years/ or as necessary.  
7. SPARK PLUG:Clean/adjust every 6 months/or 100 hours.  
Replace every year/ or 300 hours.  
Bearing Lubrication Care  
WARNING  
There are seven (7) grease points for the FS3SP Push Model  
saw, and nine (9) grease points for the FS3SP Self-Propelled  
Model saw. [Use only Premium Lithium 12 based Grease,  
conforming to NLG1 Grade #2 consistency.]  
The following procedures devoted to mainte-  
nance can prevent serious saw damage or  
malfunctioning. Before servicing or inspection,  
ALWAYS park the saw on a level surface with  
the blade removed, and the Console Engine ON/OFF switch &  
Engine ON/OFF switch in “OFF” position.  
1. Front Wheels (2): Grease daily, see page 42, item 3,  
UndercarriageAssembly.  
2. RearWheels (2):Grease daily, see page 44, item 10, Rear  
AxleAssembly.  
WARNING  
3. Blade Shaft Bearings (2): Grease daily, see page 46,  
item6, Blade Shaft Assembly.  
Some maintenance operations may require  
the engine to be run. Ensure that the mainte-  
nance area is well ventilated. Exhaust contains poisonous car-  
bon monoxide gas that can cause of unconsciousness and may  
result in DEATH  
4. Raise/Lower AdjustTube (1): Grease daily, see page 58,  
item20, Raise/LowerAssembly.  
5. Transmission Shaft Bearings (2): Grease weekly, see  
page 68, item 16,Transmission Assembly.  
General Engine Care  
1. ENGINE CHECK: Check daily for any oil and/or fuel leakage,  
thread nut & bolt tightness, and overall cleanliness.  
2. ENGINE OIL:Check daily.Inspect with blade removed and  
saw frame level on a level surface. Keep the oil clean, and  
at the proper servicing level (Figure 7).DO NOT OVERFILL!  
SAE 10W-30 of SG is recommended for general use.  
NOTE  
When cutting DRY, lubricate blade shaft bearings 2  
to 3 times daily.The grease can provide an added  
protective seal for the bearings.  
3. ENGINE OIL CHANGE: Change engine oil the first month  
or 20 hours of operation.Then every 3 months/ or 50 HOURS  
NOTE  
ALWAYS dispose of used oil in a responsible  
manner.Ensure that the disposition of all hazardous  
waste is handled properly. Call your Recycling  
Center for information about recycling engine oil.  
MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #0 (07/15/02) — PAGE 31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FS3SP CONCRETE SAW — MAINTENANCE  
GeneralTransmission Care  
AdjustV-Belt Alignment/Replacement Pulleys  
All FS3SP Models utilize spline gear wheel design coupled  
with an EATON Model 7 HydrostaticTransmission that provides  
forward/reverse propulsion. The simple design of the system  
keeps maintenance to a minimum.  
TheV-belts and their respective pulleys have been professionally  
aligned at the factory. If there is a requirement to remove/replace  
or adjust the pulleys, proceed with the following instructions.  
1. Select the proper sized pulley both in outside diameter and  
arbor size. Use approved Multiquip parts to ensure the  
component compatibility.  
1. Transmission Reservoir Cup: Check every 8 hours  
of operation. When the transmission is cold (A), check oil  
level against the level indicator (see Figure 25).  
2. AchangeinPulleydiametersmayrequirespecificallysized  
V-Belts. Contact Multiquip Servive Department to en-  
sureV-Beltcompatibility.  
DO NOT use multiple viscosity oils! DO NOT OVERFILL.  
Complete DriveV-Belt(s) Replacement steps (1 through 7)  
3. Remove theV-Belts from around the Pulley(s).  
4. Removethesetscrewsthatsecurethepulleystotherespec-  
tive shafts (PTO shaft) for engine pulley or the (bade shaft)  
for the blade shaft pulley.  
5. Remove/replace the pulley by sliding it off the shaft.  
6. Reorient the new pulley on the shaft, and ensure precise  
pulleyalignmentbyutilizinganaccuratestraightedge(see  
Figures 26 and 27).  
Figure 25. Transmission Reservoir  
7. Replace/tightensetscrewstreatedwithadropofLOCTITE  
2. Servicing: The transmission reservoir is factory filled.  
Shouldservicingberequired,useSAE20W-20,APIclassi-  
fication (SE,CC,CD) or better, General Motors Dexron B,  
FordM2C-33F,M2C-41AorInternationalHarvesterHy-Tran  
fluids. For extreme hot weather, drain oil and refill with an  
oil having a viscosity of SAE30W-30 or SAE40W-40.  
Threadlocker 266.  
8. Orient the proper replacement V-Belt(s) around the blade  
shaft pulley and engine pulley.  
9. Reference the final stages of the DriveV-Belt(s) Replace-  
m
3. Drive Chain: Check every 50 hours. Periodically wipe the  
chain clean and relubricate with penetrating chain oil.  
Thedrivechainmaystretchrequiringtensionadjustments.  
Loosen the (3) transmission attachment screws (see page  
68, item 11), and pivot the transmission in the“U”slots of  
thetransmission mount untilthepropertensionisachieved.  
(see page 68, item 12). EXCESSIVETENSION ONTHE  
DRIVE CHAINWILL REDUCE CHAIN LIFE.  
Figure 26. Pulley Alignment  
Figure 27.V-Belt Alignment  
PAGE 32 — MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #0 (07/15/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FS3SP CONCRETE SAW — MAINTENANCE  
Blade Shaft Bearing Replacement  
3. To loosen the tension on the three V-Belts perform the  
following:  
The FS3SP is supported by “tapped base lock collar (w/set  
screw)’ self-aligning blade shaft bearings. These heavy duty  
bearings support the 1-1/4 blade shaft, and have grease (zerk)  
points (Figures 28 and 29) conveniently located for service.  
z
z
z
Remove the Belt Guard, item, page 50, item 17  
(Pointers and Covers Assembly)  
Loosen the Carriage Bolt, page 48, item 4 (Engine  
Mount Assembly).  
Loosen the Hex Head Cap Screws, page 48, item 7  
(Engine Mount Assembly).  
z
Rotate the engine down to provide slack in the V-Belts  
Replacement of the Blade Shaft Bearings  
4. Perform the following to replace the blade shaft bearings:  
z
Remove blade flanges (page 46, items 7 and 8, Blade  
Shaft Assembly) as required to permit the Shaft Bearing(s)  
to slide off the blade shaft.  
z
Loosen/remove shaft bearing(s) hex head cap screws,  
page 44, item 11.  
z
z
Loosen set screw on the blade shaft bearing collar.  
Slide “old” bearing(s) off the blade shaft and replace with  
“new” bearing(s)- grease (zerk) fitting pointing forward, and  
the lock collar oriented to the “right" as you face the saw.  
Figure 28. Right-Side Shaft Bearing  
1. Reference pages 46 ( Blade Shaft Assembly) and  
72 ( Engine Mount Assembly).  
5. Looselyboltthebearing(s)intoplaceonthesawframe,then  
ensurethealignmentbyreferencingpastbearingposition-  
ing.  
2. Its recommended to replace both left & right hand bearings  
collectively.  
6. Tightenthehexheadcapscrew,page46,item11tosecure  
the shaft bearing (s) to the frame.  
7. Tocompletethere-installationprocess,reversetheorderof  
the above mentioned steps. For V-belt adjustmemt and  
tensioning see pages 32 (Figures 26 and 27) and page  
34(Figure 30).  
W — TRANSMISSION ASSY.  
Figure 29. Left-Side Shaft Bearing  
MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #0 (07/15/02) — PAGE 33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FS3SP CONCRETE SAW — MAINTENANCE  
AdjustV-BeltTension  
DriveV-Belt Check  
Operating the saw with less than four (4)V-belts, or belts that are  
slipping or are OverTensioned will significantly diminish the  
performance of the saw, and may cause damage to the blade.  
1. Tightendowntheenginemountcarriagebolt(page48,item  
4,) and monitor the tension on the belts.  
2. Determine the proper tension (Figure 31) by using a  
tensionmeter against the inside belts at mid point between  
thetwopulleys(6-9lbs.), orbydeflectingthecenterbeltsat  
mid point 3/8” (10 mm) to 1/2” (13 mm).  
1. The V-Belts of the FS3SP have been factory set utilizing  
precisionstandards.  
DriveV-Belt(s) Replacement  
Reference Pointers and Covers Assembly (page 50), Blade Shaft  
Assembly (page 46), Engine Mount Assembly (page 48) for this  
operation.  
CORRECT V-BELT  
TENSION 3/8 IN. (10 MM) TO  
1/2 IN.(13 MM) WHEN  
DEPRESSED AT MIDPOINT  
AS SHOWN  
1. RemovetheBeltGuard(page50, item17), thenloosenthe  
tensionoftheV-Belts  
2. Loosen the Engine Mount Carriage Bolt (page 48, item 4).  
3. Loosen the (4) 3/8” HHC screws (page 48, item 7).  
4. Rotate the engine down to provide slack in theV-Belts.  
5. Loosenthe(2)3/4”HHCscrewsthatsupporttheBladeShaft  
Bearingsontheright-sideofthesaw(page46,item11,also  
see Figure 30).  
6. Removethe(2)3/4”HHCscrewsthatsecuretheBladeShaft  
BearingontheV-Belt side ofthesaw(page46,item11 also  
see Figure 30).  
Figure 31. V-Belt Adjustment/Tension  
3. Once the proper tension has been applied to the belts,  
tighten the (4) 3/8” HHC screws (page 48, item 7).  
4. Replace and secure the Belt Guard (page 50, item 17).  
Figure 30.V-Belt Removal  
General Cleanliness  
7. Orientthebladeshaftsothebelt(s)tobereplacedcanslide  
of the blade shaft pulley and engine pulley.  
Clean the machine daily. Remove all dust and slurry build up.  
If the saw is steam cleaned, ensure that lubrication is accom-  
plished AFTER steam cleaning operations.  
8. Select the proper Multiquip replacementV-Belts (see page  
46, item12).  
9. RemovethewornV-Belt(s).  
10. Orient the proper replacement V-Belt(s) around the blade  
shaft pulley and engine pulley.  
11. Replaceandtightenthe(4)3/4”HHCscrewsthatsecurethe  
Blade Shaft Bearings to the saw frame.  
PAGE 34 — MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #0 (07/15/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTE PAGE  
MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #0 (07/15/02) — PAGE 35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FS3SP SAW — EXPLANATION OF CODE IN REMARKS COLUMN  
How to read the marks and remarks used in this parts book.  
Section 1: Items Found In the “Remarks” Column  
Serial Numbers-Where indicated, this indicates a serial  
number range (inclusive) where a particular part is used.  
Model Number-Where indicated, this shows that the  
corresponding part is utilized only with this specific model  
number or model number variant.  
Section 2: Items Found In the“Remarks”Column  
Serial Numbers-Where indicated, this indicates a serial number  
range (inclusive) where a particular part is used.  
Model Number-Where indicated, this shows that the  
corresponding part is utilized only with this specific model number  
or model number variant.  
Section 3: Items Found In the“Items Number”Column  
All parts with same symbol in the number column, , #,  
, belong to the same assembly or kit.  
+
, %, or  
*
■
Note: If more than one of the same reference number is listed,  
the last one listed indicates newest (or latest) part available.  
NOTE  
The contents of this parts catalog are subject to  
change without notice.  
PAGE 36 — MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #0 (07/15/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FS3SP CONCRETE SAW — SUGGESTED SPARE PARTS  
FS3SP CONCRETE SAW 1 TO 3 UNITS  
1 to 3 Units  
Qty......... P/N.............................. Description  
MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #0 (07/15/02) — PAGE 37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FS3SP CONCRETE SAW — TROUBLESHOOTING (ENGINE)  
TABLE 7. ENGINE TROUBLESHOOTING  
SYMPTON  
POSSIBLE CAUSE  
SOLUTION  
Check gap, insulation or  
replace spark plug.  
Spark plug bridging?  
Carbon deposit on spark plug?  
Clean or replace spark plug.  
Difficult to start, "fuel is available, but no  
SPARK at spark plug".  
Short circuit due to deficient spark plug  
insulation?  
Check spark plug insulation,  
replace if worn.  
Improper spark plug gap?  
Set to proper gap.  
Console or engine ON/OFF switch is  
shorted?  
Check switch wiring, replace  
switch.  
Ignition coil defective?  
Replace ignition coil.  
Set correct spark gap and  
clean points.  
Difficult to start, "fuel is available, and  
SPARK is present at the spark plug".  
Improper spark gap, points dirtry?  
Condenser insulation worn or short  
circuiting?  
Replace condenser.  
Replace defective spark plug  
wiring.  
Spark plug wire broken or short circuiting?  
Wrong fuel type?  
Flush fuel system, and replace  
with correct type of fuel.  
Difficult to start, "fuel is available, spark  
is present and compression is normal"  
Water or dust in fuel system?  
Air cleaner dirty?  
Flush fuel system.  
Clean or replace air cleaner.  
Suction/exhaust valve stuck or protruded? Re-seat valves.  
Replace piston rings and or  
piston.  
Piston ring and/or cylinder worn?  
Difficult to start, "fuel is available, spark  
is present and compression is low"  
Cylinder head and/or spark plug not  
tightened properly?  
Torque cylinder head bolts and  
spark plug.  
Head gasket and/or spark plug gasket  
damaged?  
Replace head and spark plug  
gaskets.  
Fuel not available in fuel tank?  
Fill with correct type of fuel.  
Apply lubricant to loosen fuel  
cock lever, replace if necessary.  
Fuel cock does not open properly?  
No fuel present at carburetor.  
Fuel filter clogged?  
Replace fuel filter.  
Fuel tank cap breather hole clogged?  
Air in fuel line?  
Clean or replace fuel tank cap.  
Bleed fuel line.  
PAGE 38 — MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #0 (07/15/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FS3SP CONCRETE SAW — TROUBLESHOOTING (ENGINE)  
TABLE 7. ENGINE TROUBLESHOOTING (CONTINUED)  
SYMPTON  
POSSIBLE CAUSE  
Air cleaner not clean?  
SOLUTION  
Clean or replace air cleaner  
Check float adjustment, re-build  
carbureator.  
Improper level in carburetor?  
"Weak in power" compression is  
proper and does not misfire.  
Defective Spark plug?  
Defective Spark plug?  
Clean or replace spark plug.  
Flush fuel system, and replace  
with correct type of fuel.  
Water in fuel system?  
"Weak in power" compression is  
proper but misfires.  
Dirty spark plug?  
Clean or replace spark plug.  
Replace ignition coil.  
Ignition coil defective?  
Replace with correct type of  
spark plug.  
Spark plug heat value improper?  
Engine overheats.  
Correct type of fuel?  
Replace with correct type of fuel  
Clean cooling fins.  
Cooling fins dirty?  
Governor adjusted correctly?  
Governor spring defective?  
Adjust governor.  
Replace governor spring.  
Rotational speed fluctuates.  
Recoil starter malfunction.  
Check entire fuel system for  
leaks or clogs.  
Fuel flow restricted?  
Recoil mechanism clogged with dust and Clean recoil assembly with soap  
dirt?  
and water.  
Sprial spring loose?  
Replace sprial spring.  
TABLE 8. SELF-PROPULSION TROUBLESHOOTING  
SYMPTON  
POSSIBLE CAUSE  
SOLUTION  
Broken Drive Chain  
Replace/Repair Drive Chain  
Transmission Does Not Engage  
Spline Gear Does Not Make Proper  
Contact With Rear Wheels  
Adjust Spline Gear Control Rod  
Transmission Operates in One  
Direction  
Loose Transmission Drive Linkage  
Loose Transmission Drive Linkage  
Low Oil Level  
Adjust Transmission  
Adjust Transmission  
Service Transmission Filler Cup  
Transmission Operating Very HOT  
Cooling Louvers of the Transmission  
is Caked With Cutting Slurry  
Thouroughly Clean  
Transmission Casing  
Loose Tranmission Drive Linkage  
Loose Drive Chain  
Adjust Transmission  
Adjust Drive Chain  
Saw Slips and Demonstrates Jerky  
Motion When Engaged  
Low Oil Level  
Service Transmission Filler Cup  
Water in Reservoir or Extreme  
Overheating Has Occured  
Clean recoil assembly with  
soap and water.  
Oil in Reservoir is Dark/Milky in Color  
MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #0 (07/15/02) — PAGE 39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FS3SP CONCRETE SAW — NAME PLATE AND DECALS  
NAME PLATE AND DECALS.  
PAGE 40 — MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #0 (07/15/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FS3SP CONCRETE SAW — NAME PLATE AND DECALS  
NAME PLATE AND DECALS  
NO  
PART NO  
15578  
PART NAME  
QTY.  
REMARKS  
1
DECAL: FS3 (WHITE)  
2
2
1
1
1
1
*
2
15579  
DECAL: MQ WHITEMAN 5.5" X 4"  
DECAL: POWDER COATED  
DECAL: WARNING PROP. 65  
DECAL: WARNING RESPIRATORY  
DECAL: WARNING BLADE GUARD  
*
*
3
13118  
4
15582  
15580  
15581  
*
5
*
6
7
8
PLATE: SERIAL NO. .................................. 1 ......... CONTACT MQ SERVICE DEPT. W/MODEL & S/N  
DECAL: MQ WHITEMAN 13"  
DECAL: KIT FS3 ......................................... 1 ......... INCLUDES ITEMS W/  
2942  
15739  
1
*
9
*
SEE DECAL ILLUSTRATIONS ON PAGE 8.  
MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #0 (07/15/02) — PAGE 41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FS3SP CONCRETE SAW — UNDER CARRIAGE ASSY.  
UNDER CARRIAGE ASSY.  
6
2
5
4
1
3
PAGE 42 — MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #0 (07/15/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FS3SP CONCRETE SAW — UNDER CARRIAGE ASSY.  
UNDERCARRIAGE ASSY.  
NO.  
1
2
3
4
5
6
PART NO.  
10512  
15028  
15090  
15202  
15377  
15382  
PART NAME  
QTY.  
REMARKS  
RING, SNAPTRUARC #5100- 56  
SET COLLAR, 5/8 DIAMETER  
WHEEL, 5D X 2W X .625 ID #400 CAP  
UNDERCARRIAGEW/A  
2
2
2
1
1
2
AXLE, PIVOT, UNDERCARRIAGE  
BUSHING, PIVOT AXLE  
MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #0 (07/15/02) — PAGE 43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FS3SP CONCRETE SAW — REAR AXLE ASSY.  
10  
18  
1
16  
15  
2
4
5
7
8
14  
11  
1
3
9
6
13  
12  
NOTES:  
INCLUDED WITH SET COLLAR  
ITEM 5.  
1
PAGE 44 — MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #0 (07/15/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FS3SP CONCRETE SAW — UNDER CARRIAGE ASSY.  
REAR AXLE ASSY.  
NO.  
1
2
3
4
5
6
7
8
PART NO.  
0166A  
10136  
1284  
PART NAME  
QTY.  
4
4
4
4
2
1
1
1
1
2
1
1
1
2
2
2
REMARKS  
WASHER, LOCK, 3/8 MEDIUM  
WASHER, FLAT, 3/8 SAE  
SCREW, HHC 3/8- 16 X 1- 1/2  
NUT, HEX FINISH 3/8- 16  
SET COLLAR, 5/8 DIAMETER  
NUT, 1- 14- 2B  
1456  
15028  
15092  
15093  
15106  
15213  
15278  
15279  
15356  
15361  
15372  
15417  
3264  
NUT, 1- 14 2B- LH  
POINTER, REAR, W/A  
REAR AXLE SELF PROPELLED  
WHEEL, REAR 10.00 X 2.50  
KEY, 0.25 X 0.25 X 3.25  
BUSHING, TL SH X 1  
SPROCKET, TL 40TB48  
BEARING, FLANGED, 1” BORE  
SPACER, REAR AXLE, SPROCKET  
WASHER, FLAT 1” SAE  
KEY, 1/4 SQ. X 2”  
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
6059B  
1
2
SET SCREW  
MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #0 (07/15/02) — PAGE 45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FS3SP CONCRETE SAW — BLADE SHAFT ASSY.  
BLADE SHAFT ASSY.  
11  
11  
10  
18  
9
8
12  
7
13  
6
3
14  
6
5
19  
7
1
4
15  
2
3
17  
LUBRICATION  
POINT  
16  
1
2
LUBRICATION  
POINT  
PAGE 46 — MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #0 (07/15/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FS3SP CONCRETE SAW — BLADE SHAFT ASSY.  
BLADE SHAFT ASSY.  
NO  
1
PART NO  
2621  
PART NAME  
QTY.  
REMARKS  
ZERK FITTING  
2
2
2
1
1
2
2
1
1
4
4
2
1162A  
15119  
6059B  
15065  
15066  
15063  
15012  
15093  
0448  
15563  
10799  
15897  
15365  
15366  
15060  
CAP, ZERK FITTING  
3
KEY, WOODRUFF #91, ANS1 #8061  
KEY, /4 SQ. X 2"  
4
5
SHAFT, BLADE  
6
BEARING, PILLOW BLOCK 1 1/4 BORE  
FLANGE, BLADE INSIDE  
FLANGE, DRIVEN ASSY.  
NUT, 1-14-2B-LH  
7
8
9
10  
11  
12  
12  
13  
13  
14  
15  
16  
17  
18  
19  
WASHER, FLAT 7 / 16 SAE  
SCREW, HHC 7/16 -14 X 3/4  
V-BELTS 3VX375 ........................................ 4 ........... 20 HP ENGINE HONDA 14" BLADE  
V-BELTS 3VX355 ........................................ 4 ........... 20 HP ENGINE HONDA 20" BLADE  
PULLEY, 4/3V4.12 X 1.125 ID/3L2.75.......... 1 ........... 20 HP ENGINE HONDA 14" BLADE  
PULLEY, 4/3V3.00 X 1.125 ID/3L2.75.......... 1 ........... 20 HP ENGINE HONDA 20" BLADE  
B
USHING, OD SDS X 1- 1/4 X 1/4  
1
1
1
2
4
2
15148  
15092  
1528  
2955  
25281  
SPACER, 1.320D X 1.051D X 0.53  
NUT, 1-14-2B  
SCREW, SHS 1/4-20 X 5/16 HDP  
WASHER, LOCK 7/16 MED  
SPACER, 1.75 OD X 1.00 ID X .15  
MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #0 (07/15/02) — PAGE 47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FS3SP CONCRETE SAW — ENGINE MOUNT ASSY.  
ENGINE MOUNT ASSY.  
7
1
6
3
5
1
3
5
4
8
PAGE 48 — MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #0 (07/15/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FS3SP CONCRETE SAW — ENGINE MOUNT ASSY.  
MOUNT, ENGINE ASSY.  
NO.  
1
2
3
4
5
6
7
8
PART NO.  
0166A  
1007  
10136  
15174  
15680  
1665  
PART NAME  
WASHER, LOCK, 3/8 MEDIUM  
NUT, HEX JAM 3/8 - 16  
WASHER, FLAT 3/8 SAE  
BOLT, CARRIAGE 3/8- 16 X 3  
MOUNT, ENGINE W/A  
SCREW, HHC 3/8- 16 X 2  
SCREW, HHC 3/8- 16 X 1, GRD 8  
WASHER, FLAT 3/8 PLTD STD. USS  
QTY.  
REMARKS  
4
1
6
1
1
4
4
2
25301  
4001  
MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #0 (07/15/02) — PAGE 49  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FS3SP CONCRETE SAW — POINTERS AND COVERS ASSY.  
POINTERS AND COVERS ASSY.  
18  
21  
12  
11  
15  
A
22  
13  
16  
14  
20  
17  
19  
5
4
10  
9
1
8
2
6
3
7
NOTES:  
ITEM 15 PLACED ON  
UNDERSIDE OF COVER  
A
PAGE 50 — MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #0 (07/15/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FS3SP CONCRETE SAW — POINTERS AND COVERS ASSY.  
POINTER FRONT ASSY.  
NO.  
1
2
3
4
5
6
7
8
PART NO.  
0131A  
0447  
0949  
10133  
1023  
15052  
15053  
15889  
15113  
15114  
181B  
0205  
0948  
10930  
11534  
15293  
15381  
4001  
PART NAME  
QTY.  
1
1
1
2
2
1
1
1
1
1
4
1
4
2
4
1
REMARKS  
SCREW, HHC 1/4- 20 X 3/4  
WASHER, FLAT 1/2 SAE  
NUT, HEX FINISH 1/4- 20  
NUT, NYLOC 3/8- 16  
SCREW, HHC 3/8- 16 X 1- 1/4  
ROD, POINTER  
WHEEL, POINTER ARM  
POINTER, LONG FRONT, W/A  
SASH, POINTER RETAINER  
SLEEVE, SASH  
WASHER, LOCK, 1/4 MEDIUM  
SCREW, HHC 3/8- 16 X 1  
WASHER, FLAT, 1/4 SAE  
WASHER, FENDER 1/4- X 1 1/4  
NUT U TYPE 1/4- 20  
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
COVER, TRANS. BELT  
COVER, BELT GUARD W/A  
WASHER, FLAT 3/8 PLTD. STD. USS  
SCREW, HHC 1/4- 20 X 5/8  
SCREW, HHC 1/4- 20 X 3/4  
PIN, DOWEL 3/8  
1
1
3
3
1
1
4514  
0131A  
15046  
15064  
FLANGE, BLADE DRIVEN SIDE  
MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #0 (07/15/02) — PAGE 51  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FS3SP CONCRETE SAW — WATER SYSTEM ASSY.  
WATER SYSTEM ASSY.  
4
2
3/8 DIA. HOSE  
16 IN. (41 CM.)  
5
6
3
CONNECT  
WATER SOURCE  
HERE  
1
4
9
10  
2
3/8 DIA. HOSE  
58 IN. (147.32 CM.)  
8
3
7
PAGE 52 — MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #0 (07/15/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FS3SP CONCRETE SAW — WATER SYSTEM ASSY.  
FS3, WATER ASSY.  
NO.  
1
2
3
4
5
6
7
PART NO.  
15180  
15181  
15538  
15546  
15766  
15767  
15768  
PART NAME  
QTY.  
REMARKS  
FITTING, STR 6 BARB- 1/2 MP  
HOSE, 3/8 BLACK WATER 200PSI  
CLAMP, WORM HOSE, 7/16- 11/16  
GASKET, 3/4 HOSE GASKET/SCREEN  
VALVEL, 2 WAY 3/8 BARB X 3/8 MPT  
FITTING, 6FPT- 6BARB  
1
5.5  
4
1
1
1
1
FITTING, 6BARB 3/4 MALE HOSE  
8
15769  
15546  
15076  
FITTING, 3/4 HOSE QUICK REL. FEMALE  
GASKET, 3/4 HOSE GASKET / SCREEN  
FITTING, STR 3/4 FEM HOSE X 1/2 MP  
1
1
1
9
10  
MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #0 (07/15/02) — PAGE 53  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FS3SP CONCRETE SAW — BASIC PLATFORM ASSY.  
BASIC PLATFORM ASSY.  
4
5
5
21  
5
25  
22  
5
24  
23  
7
8
9
8
3
10  
11  
12  
5
1
13  
1
14  
15  
16  
1
14  
2
15  
13  
17  
18  
2
19  
3
1
20  
2
NOTES:  
USE LOCTITE 271 ON ITEM 13,  
SCREW, HHC 3/8-16 X 1  
1
2
REFERENCE PAGES 66 AND 67  
FOR COMPLETE PARTS BREAK-  
DOWN FOR BARE PLATFORM ASSY.  
P/N 15409.  
PAGE 54 — MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #0 (07/15/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FS3SP CONCRETE SAW — BASIC PLATFORM ASSY.  
COVER ASSY., REAR  
NO.  
1
2
3
4
5
6
7
8
PART NO.  
0916  
PART NAME  
SCREW, RHM 1/4- 20- X 3/4  
NUT, NYLOC 1/4- 20  
NUT U TYPE 1/4- 20  
SCREW, HHC, WASHER 1/4- 20 X 3/4  
COVER, REAR  
QTY.  
4
4
6
6
1
1
2
1
2
1
1
2
4
6
11  
4
4
1
1
1
1
4
4
4
1
REMARKS  
10024  
11534  
11819  
15266  
29057  
15081  
15701  
15081  
15702  
15212  
15505  
0166  
10133  
10136  
16524  
5054A  
15703  
15097  
15098  
15138  
0131A  
0181B  
0948  
DOCUMENT BOX, (CP90007- 07)  
HANDLE, 1” DIAMETER  
HANDLEBAR, LEFT W/A  
HANDLE, 1” DIAMETER  
HANDLEBAR, RIGHT W/A  
CONSOLE W/A FS3  
KNOB, COMFORT GRIP  
SCREW, HHC 3/8- 16 X 7/8  
NUT, NYLOC 3/8- 16  
WASHER, FLAT 3/8 SAE  
SCREW, HHC 1/2- 13 X 1- 1/4  
WASHER, LOCK, 1/2 MEDIUM  
BALE, LIFT W/A  
WRENCH, ALL PURPOSE  
TOOL, SHAFT LOCK SOCKET W/A  
WRENCH, 6” POCKET SOCKET  
SCREW, HHC 1/4- 20 X 3/4  
WASHER, LOCK, 1/4 MED.  
WASHER, FLAT, 1/4 SAE  
COVER, CHAIN GUARD  
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
15398  
MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #0 (07/15/02) — PAGE 55  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FS3SP CONCRETE SAW — BLADE MIST 20 -INCH ASSY.  
BLADE MIST 20-INCH ASSY.  
20  
21  
23  
8
15  
17  
7
7
7
16  
18  
2
1
11  
22  
12  
7
4
6
3
5
19  
10  
14  
13  
9
7
5
PAGE 56 — MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #0 (07/15/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FS3SP CONCRETE SAW — BLADE MIST 20 -INCH ASSY.  
GUARD, BLADE 20” ASSY.  
NO.  
1
2
3
4
5
6
7
8
PART NO.  
0130A  
0131A  
0424  
0730  
0948  
PART NAME  
QTY.  
2
2
2
2
6
4
10  
2
1
1
1
1
1
1
1
2
1
REMARKS  
SCREW, SHS 1/4- 20 X 1/4  
SCREW, HHC 1/4- 20 X 3/4  
SCREW, HHC 1/4- 20 X 1 1/4  
SCREW, HHC 1/4- 20 X 1  
WASHER, FLAT 1/4 SAE  
NUT, HEX FINISH 1/4- 20  
NUT, NYLOC 1/4- 20  
0949  
10024  
11505  
15043  
15096  
15161  
15462  
15463  
15503  
15504  
15506  
15507  
15508  
15509  
15770  
15842  
25023  
26250  
CLAMP, HOSE SUPPORT 1/2 INCH LONG  
FLAP, NEOPRENE WATER SHIELD  
ANGLE, SPLASH GUARD  
STOP, RUBBER BUMPER  
GUARD BLADE 20” BODY W/A  
GUARD BLADE 20”DOOR W/A  
KNOB, CONFORT GRIP  
MANIFOLD, (CIPSA)  
TUBE, FLOOD  
GASKET, MANIFOLD FLOOD  
PLUG (CIPSA)  
SPRING, CENTURY SPRING #  
FITTING, 3/4 HOSE QUICK REL. MALE  
FITTING, 1/2MP- 3/4 F HOSE  
PIN, HINGE- 1/2 X 3.22  
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
2
1
1
1
1
4
SCREW, HHC 1/4- 20 X 1- 3/4  
MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #0 (07/15/02) — PAGE 57  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FS3SP CONCRETE SAW — MANUAL RAISE AND LOWER ASSY.  
MANUAL RAISE AND LOWER ASSY.  
15  
8
5
11  
6
1
13  
2
21  
3
14  
9
18  
4
16  
17  
LUBRICATION  
POINT  
20  
8
7
12  
10  
22  
19  
PAGE 58 — MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #0 (07/15/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FS3SP CONCRETE SAW — MANUAL RAISE AND LOWER ASSY.  
MANUAL LIFT ASSY.  
NO.  
1
2
3
4
5
6
7
8
PART NO.  
0131A  
0949  
10024  
10133  
10136  
1023  
PART NAME  
QTY.  
2
1
3
2
2
2
1
1
1
1
1
1
1
1
1
1
REMARKS  
SCREW, HHC 1/4- 20 X 3/4  
NUT, HEX FINISH 1/4- 20  
NUT, NYLOC 1/4 - 20  
NUT, NYLOC 3/8- 16  
WASHER, FLAT 3/8 SAE  
SCREW, HHC 3/8- 16 X 1- 1/4  
NUT, HEX FINISH 3/8- 16  
PLUNGE, BALL  
BEARING, DEPTH GAUGE  
PIN, HEADED BLADE ADJUST  
SPACER, DEPTH, ADJUSTER  
LOWER ARM W/A, DEPTH CONTROL  
GAUGE, DEPTH  
BRACKET, DEPTH GAUGE  
HANDLE, MANUAL R/ L ASSEMBLY  
SPACER, 1” OD X 0.77” ID X 1.31” L  
SPRING, EXTENSION 5L X 0.25D X .038d  
CABLE ASSEMBLY DEPTH GAUGE  
PIN, COTTER 1/8 X 1- 1/2  
ZERK, GREASE STR. 1/4- 28  
SCREW, HHC 1/4- 20 X 1/4 GRD. 8  
WASHER, FLAT 3/4 SAE  
1456  
15054  
15080  
15083  
15089  
15206  
15704  
15708  
15710  
15712  
15717  
15738  
2219  
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
1
1
1
1
1
2
2621  
26385  
8151  
MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #0 (07/15/02) — PAGE 59  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FS3SP CONCRETE SAW — PLUG KIT (PUSH) ASSY.  
PLUG KIT (PUSH) ASSY.  
PAGE 60 — MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #0 (07/15/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FS3SP CONCRETE SAW — PLUG KIT (PUSH) ASSY.  
PLUG KIT (PUSH) ASSY.  
NO  
1
PART NO  
0916  
PART NAME  
QTY. REMARKS  
SCREW, HHC RHM 1/4-20 X 3/4  
WASHER, FLAT  
8
8
8
1
1
8
1
1
1
3
2
0948  
3
10024  
15208  
15339  
15340  
15341  
15342  
15345  
15553  
NUT, NYLOC 1/4-20  
4
COVER, PROPEL LEVEL FS2  
COVER, FS2 ENGAGE HOLE  
PLUG, 0.65 DIA X 14 GA, BLACK  
PLUG, 0.44 DIA X 14 GA, BLACK  
PLUG, 0.38 DIA X 14 GA, BLACK  
PLUG, 0.28 DIA X 14 GA, BLACK  
SWITCH, BLANK  
5
6
7
8
9
10  
MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #0 (07/15/02) — PAGE 61  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FS3SP CONCRETE SAW — PLUG KIT (SELF PROPPELLED) ASSY.  
PLUG KIT (SELF PROPELLED) ASSY.  
PAGE 62 — MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #0 (07/15/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FS3SP CONCRETE SAW — PLUG KIT (SELF PROPPELLED) ASSY.  
PLUG KIT (SELF PROPELLED) ASSY.  
NO  
1
PART NO  
0916  
PART NAME  
QTY. REMARKS  
SCREW, HHC RHM 1/4-20 X 3/4  
WASHER, FLAT  
2
2
2
8
1
1
1
3
2
0948  
3
10024  
15340  
15341  
15342  
15345  
15553  
NUT, NYLOC 1/4-20  
4
PLUG, 0.65 DIA X 14 GA, BLACK  
PLUG, 0.44 DIA X 14 GA, BLACK  
PLUG, 0.38 DIA X 14 GA, BLACK  
PLUG, 0.28 DIA X 14 GA, BLACK  
SWITCH, BLANK  
5
6
7
8
MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #0 (07/15/02) — PAGE 63  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FS3SP CONCRETE SAW — BATTERY BOX ASSY.  
BATTERY BOX ASSY.  
1
1
4
2
2
3
NOTES:  
BRACKET IS ON INSIDE OF  
CONSOLE CHASSIS  
1
ITEMS 2 AND 3 ARE ATTACHED  
ON THE UNDERSIDE OF THE  
PLATFORM  
2
PAGE 64 — MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #0 (07/15/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FS3SP CONCRETE SAW — BATTERY BOX ASSY.  
BATTERY BOX ASSY.  
NO  
1
PART NO  
15203  
0948  
10024  
0471  
PART NAME  
QTY. REMARKS  
BATTERY HOLD DOWN  
WASHER, FLAT 1/4" SAE  
NUT, NYLOCK 1/4 - 20  
BATTERY, WET GR.U1  
1
1
1
1
2
3
4
MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #0 (07/15/02) — PAGE 65  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FS3SP CONCRETE SAW — PLATFORM (BARE) ASSY.  
PLATFORM (BARE) ASSY.  
13  
8
10  
TOP VIEW  
13  
9
1
12  
2
3
SIDE VIEW  
13  
5
7
14  
4
6
BOTTOM VIEW  
PAGE 66 — MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #0 (07/15/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FS3SP CONCRETE SAW — PLATFORM (BARE) ASSY.  
PLATFORM (BARE) ASSY.  
NO  
1
PART NO  
15035  
15069  
15214  
15215  
15373  
15374  
15428  
15453  
15455  
15672  
15682  
15742  
20530  
20533  
968011  
PART NAME  
QTY. REMARKS  
MOUNT, BLADE GUARD BAYONET  
MOUNT, FRONT POINTER  
PLATFORM  
4
4
1
2
1
1
1
1
1
1
2
1
1
2
4
2
3
4
SUPPORT, PLATFORM  
5
SUPPORT, REAR AXLE RIGHT  
SUPPORT, REAR AXLE LEFT  
SUPPORT, CROSS PLATFORM  
PLATE, MOUNT, BELT COVER  
TAB, SPRING IDLER  
6
7
8
9
10  
11  
12  
13  
14  
15  
TAB, IDLER MOUNT  
MOUNT, ENGINE / TRANS SIDE  
STIFFENER, REAR PLATFORM  
NUT, WELD, HEX LOCK 3/8-16  
NUT, WELD, HEX LOCK 1/4-20  
NUT, HEX FINISH 1/2-13  
MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #0 (07/15/02) — PAGE 67  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FS3SP CONCRETE SAW — TRANSMISSION ASSY.  
TRANSMISSION ASSY.  
4
2
4 PLACES  
25  
8
10  
5
7
1
13  
14  
3
ENGINE  
PULLEY  
26  
O
T
O
IL  
L
E
V
L
H
E
O
IL  
L
E
V
L
COLD  
E
2
30  
24  
2
22  
1
2
6
17  
28  
16  
12  
27  
18  
2
15  
8
19  
11  
IDLER  
PULLEY  
PUMP  
PULLEY  
29  
2
LUBRICATION  
POINT  
2
23  
31  
9
21  
LUBRICATION  
POINT  
CONNECTS TO  
REAR AXLE  
NOTES:  
DO NOT OVER TIGHTEN. IDLER  
PULLEY SHOULD BE FREE TO  
MOVE.  
1
USE LOCTITE P/N 60091 (BLUE).  
2
3
THROTTLE CABLE INCLUDED WITH  
HANDLE.  
PAGE 68 — MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #0 (07/15/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FS3SP CONCRETE SAW — TRANSMISSION ASSY.  
HYDROSTATIC DRIVE ASSY.  
NO.  
1
2
3
4
PART NO.  
0105  
0161D  
0166  
PART NAME  
QTY.  
1
1
6
4
REMARKS  
SCREW, HHC 5/16- 18 X 1 1/2  
NUT, HEX FINISH 5/16- 18  
SCREW, HHC 3/8- 16 X 7/8  
SCREW, HHC 3/8- 16 X 1  
0205  
5
6
7
8
0300B  
10019  
10133  
10136  
1162A  
11644  
1493  
WASHER, FLAT 5/16 SAE  
NUUT, NYLOC 10- 32  
NUT, NYLOC 3/8- 16  
WASHER, FLAT 3/8 SAE  
CAP, GREASE ZERK #2  
SCREW, HHC, WASHER 10- 32 X 5/8  
SCREW, HHC 3/8- 16 X 3- 1/4  
MOUNT, TRANSMISSION, W/A  
DISENGAGE LEVER, W/A  
DISENGAGE, LATCH CLAMP  
SHAFT, REDUCTION, TRANS.  
BEARING,PIL. BLK., BRN. VTBS- 212  
SPROCKET, 40BS10 X 17MM X 1/8  
SPROCKET, TL 40TB48  
1
4
7
20  
2
4
3
1
1
1
1
2
1
1
1
2
2
1
1
2
4
1
1
1
2
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
31  
15288  
15300  
15301  
15355  
15359  
15360  
15361  
15363  
15371  
15379  
15389  
15390  
15391  
0166A  
15432  
25040  
29096  
0627  
SHEAVE, TL 1/3V106(3.35)  
MOUNT, DRIVE SYSTEM  
SPROCKET, 40BS10 X 3/4 X 3/16  
CHAIN, ROLLER #40S X 57P  
CHAIN, ROLLER #40S X 63P  
CONNECTOR LINK #40 CHAIN  
WASHER, LOCK 3/8 MED  
BELT, 3L ACCU- LINK WITH INSTRUCTION SHEET  
TRANSMISSION, EATON MODEL 700- 001  
NUT, HEX 5/16- 18 PLAIN  
KEY, SQUARE 3/16 x 1-1/4  
KEY, WOODRUFF #3  
ZERK FITTING  
1578  
2621  
1
2
MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #0 (07/15/02) — PAGE 69  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FS3SP CONCRETE SAW — TRANSMISSION ASSY.  
HYDROSTATIC THROTTLE ASSY.  
TRANSMISSION  
ENGAGEMENT  
LEVER  
6
10  
8
4
5
9
7
12  
2
3
1
1
13  
12  
O
T
O
IL  
L
E
V
L
H
E
O
IL  
L
E
V
L
COLD  
E
14  
15  
19  
16  
4
17  
18  
NOTES:  
BRACKET FOUND ON RIGHT SIDE  
OF CONSOLE INTERIOR  
1
PAGE 70 — MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #0 (07/15/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FS3SP CONCRETE SAW — TRANSMISSION ASSY.  
HYDROSTATIC THROTTLE ASSY.  
NO.  
1
2
PART NO.  
0131A  
0937  
PART NAME  
SCREW, HHC 1/4- 20 X 3/4  
NUT, HEX #10- 32  
QTY.  
4
2
REMARKS  
3
4
5
6
7
8
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
0948  
WASHER, FLAT, 1/4 SAE  
NUT, NYLOC 10- 32  
NUT, NYLOC 1/4- 20  
2
2
4
1
1
2
1
1
1
2
1
1
4
4
2
4
10019  
10024  
11379  
11644  
12287  
15773  
15774  
15789  
2153  
LEVER, THROTTLE  
SCREW, HHC, WASHER 10- 32 X 5/8  
SCREW, THP 1/4- 20 X 3/4 SS  
BRACKET, UPR PVT FLOW CONTROL  
BRACKET, LWR PVT FLOW CONTROL  
CABLE, THROTTLE 314VTT- 2- 30 1/4  
ROD END, 10- 32 FEMALE RH  
SCREW, HHC 10- 32 X 1  
CONTROL, PUMP W/A  
WASHER, FLAT 3/8 SAE  
SCREW, HHC 3/8- 16 X 7/8  
MOUNT, DRIVE SYSTEM  
NUT, NYLOC 3/8- 16  
3513  
15395  
10136  
0166  
15371  
10133  
0166A  
WASHER, LOCK 3/8 MED  
4
MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #0 (07/15/02) — PAGE 71  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FS3SP CONCRETE SAW — ENGINE ASSY.  
ENGINE ASSY.  
PAGE 72 — MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #0 (07/15/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FS3SP CONCRETE SAW — ENGINE ASSY.  
ENGINE ASSY.  
NO  
1
PART NO  
15729  
15104  
15743  
15386  
15769  
6059B  
PART NAME  
QTY.  
REMARKS  
ENGINE, KOHLER 20 HP W/CHARGE  
ENGINE, HONDA 20HP GX620TXF2  
TUBE, OIL DRAIN ASSY.  
BUSHING, TL 1.125” BORE  
PULLEY, 1.75TL 4/3V 3.00OD  
KEY, 1/4”SQ. X 2”  
1
1
1
1
1
1
1
2
3
4
5
MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #0 (07/15/02) — PAGE 73  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FS3SP CONCRETE SAW — WIRING DIAGRAM.  
FS3SP ELECTRIC START WIRING DIAGRAM  
9-PIN  
CONNECTOR CONNECTOR  
MALE FEMALE  
9-PIN  
ENGINE SIDE  
BLK/RED (PICK-UP COIL)  
BLK 16 AWG  
CONSOLE SIDE  
ENGINE STOP  
DIODES  
BLK 16 AWG  
WHT 16 AWG  
WHT  
SPLICE  
SPARK  
PLUG  
SPARK  
PLUG  
UNIT  
UNIT  
EMERGENCY  
STOP BUTTON  
CHASSIS  
GND.  
CHASSIS  
GND.  
IGNITION  
COIL  
IGNITION  
COIL  
(CB1)  
30 AMPS  
NC  
(+12 VDC) RED 12 AWG  
RED 12 AWG  
BL 16 AWG  
RED 12 AWG  
WH 12 AWG  
1
2
CHASSIS  
GND.  
(START SOLENOID)  
BL 16 AWG  
START  
PUSHBUTTON  
CLUTCH  
ENGAGEMENT  
MICRO-SWITCH  
BLK  
BL  
16 AWG 16 AWG  
STARTER  
SOLENOID  
3
1
NEUTRAL  
CLOSED  
SOLDER  
JOINT  
POSITIVE  
BLK 16 AWG  
SOLDER  
JOINT  
(HOUR METER SIGNAL)  
BLK 16 AWG  
BLK 16 AWG  
SHIELD  
HOUR  
METER  
FUSE  
HOLDER  
BATTERY  
BLK 16  
AWG  
SHIELD  
F1  
M
SPARK  
PLUG  
BLK 16  
AWG  
20 AMP.  
CHASSIS  
GND.  
CHASSIS  
GND.  
TO PUMP ROCKER  
SWITCH PIN 3  
WH 16 AWG  
NEGATIVE  
CHASSIS  
GND.  
(FUEL CUT SOLENOID)  
RED 16 AWG  
BLK/YEL  
RED 16 AWG  
SPLICE  
WH 16 AWG  
EMERGENCY  
STOP BUTTON  
FUEL CUT  
SOLENOID  
TO PUMP ROCKER  
SWITCH PIN 11  
BLK 16 AWG  
NO  
3
4
(LOW OIL  
NC  
SHUT-DOWN)  
GRN 16 AWG  
SPLICE  
GRN 12 AWG  
GRN  
CHASSIS  
GND.  
OIL LEVEL  
SWITCH  
GRAY  
GRAY  
WHT 12 AWG (BATTERY)  
BLK 12 AWG (GND)  
WHT 12 AWG  
SPLICE  
NC  
BLK 12 AWG (GND)  
CHARGE COIL  
3 AMPS  
9-POS FEMALE PLUG  
(BACK VIEW)  
12 AWG  
RED  
12 AWG  
WHT  
16 AWG  
RED  
COLOR CODE  
CHASSIS  
GND.  
BLK  
WHT  
RED  
YEL  
GRN  
BLACK  
WHITE  
RED  
YELLOW  
GREEN  
16 AWG  
BLK  
16 AWG  
RED  
16 AWG  
RED  
HM  
SIGNAL  
HM  
SHIELD  
16 AWG  
RED  
REGULATOR/  
RECTIFIER  
GRAY GRAY  
BL BLUE  
PAGE 74 — MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #0 (07/15/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FS3SP CONCRETE SAW — WIRING DIAGRAM.  
FS3SP ELECTRIC START WIRING DIAGRAM  
(ROCKER SWITCHES)  
PUMP ON/OFF  
ROCKER SWITCH  
CONNECTOR  
LIGHT ON/OFF  
ROCKER SWITCH  
CONNECTOR  
RAISE/LOWER  
ROCKER SWITCH  
CONNECTOR  
DPDT  
SPST  
SPST  
FROM +12 VDC  
SOLDER JOINT  
WHT 16 AWG  
10  
1
5
2
6
4
8
2
3
7
4
8
12  
11  
2
6
3
7
4
8
12  
11  
3
7
12  
11  
10  
1
5
10  
1
5
6
9
9
9
FROM EMERGENCY  
STOP SWITCH PIN 4  
BLK 16 AWG  
CHASSIS GND.  
DPDT  
BLUE 16 AWG  
BLACK 16 AWG  
LIGHT INTERFACE  
CONNECTOR  
(+12 VDC)  
PUMP INTERFACE  
CONNECTOR  
(+12 VDC)  
UP  
DOWN  
MOTOR  
1
OUTPUT  
FUSE  
HOLDER  
PULSE WIDTH  
MODULATOR  
(PWM)  
RED 16 AWG  
F1  
CONNECT TO  
+12 VDC POWER  
GND  
INPUT  
10 AMP.  
CHASSIS  
GND.  
NOTES:  
THE RAISE/LOWER (CUTTING BLADE)  
CAPABILITY IS AN OPTION. CONTACT  
MULTIQUIP SALES DEPT. REGARDING  
THIS FEATURE.  
1
MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #0 (07/15/02) — PAGE 75  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Effective: July 1, 2000  
TERMS AND CONDITIONS OF SALE — PARTS  
PAYMENT TERMS  
4. Freight is at the sender’s expense. All PRICINGANDREBATES  
partsmustbereturnedfreightprepaidto  
Multiquip’sdesignatedreceivingpoint.  
Terms of payment for parts are net 10 days.  
Prices are subject to change without prior  
notice.Pricechangesareeffectiveonaspecific  
5. Parts must be in new and resalable dateandallordersreceivedonorafterthatdate  
condition,intheoriginalMultiquippackage willbebilledattherevisedprice. Rebatesfor  
(ifany),andwithMuiltiquippartnumbers price declines and added charges for price  
FREIGHTPOLICY  
All parts orders will be shipped collect or  
prepaidwiththechargesaddedtotheinvoice.  
All shipments are F.O.B. point of origin.  
Multiquip’sresponsibilityceaseswhenasigned  
manifest has been obtained from the carrier,  
andanyclaimforshortageordamagemustbe  
settledbetweentheconsigneeandthecarrier.  
clearlymarked.  
increaseswillnotbemadeforstockonhandat  
thetimeofanypricechange.  
6. Thefollowingitemsarenotreturnable:  
Multiquip reserves the right to quote and sell  
directtoGovernmentagencies,andtoOriginal  
Equipment Manufacturer accounts who use  
our products as integral parts of their own  
products.  
a. Obsolete parts. (If an item is listed  
inthepartspricebookasbeing  
replaced by another item, it is  
obsolete.)  
b. Any parts with a limited shelf life  
(such as gaskets, seals, “O” rings,  
andotherrubberparts)thatwere  
purchasedmorethansixmonths  
priortothereturndate.  
MINIMUMORDER  
SPECIALEXPEDITINGSERVICE  
TheminimumchargeforordersfromMultiquip  
is $15.00 net. Customers will be asked for  
instructionsregardinghandlingofordersnot  
meetingthisrequirement.  
A$20.00to$50.00surchargewillbeaddedto  
theinvoiceforspecialhandlingincludingbus  
c. Anylineitemwithanextendeddealer shipments, insured parcel post or in cases  
netpriceoflessthan$5.00.  
where Multiquip must personally deliver the  
partstothecarrier.  
d. Special order items.  
RETURNEDGOODSPOLICY  
e. Electricalcomponents.  
Returnshipmentswillbeacceptedandcredit  
will be allowed, subject to the following  
provisions:  
LIMITATIONSOFSELLER’SLIABILITY  
f.  
Paint,chemicals,andlubricants.  
Multiquip shall not be liable here under for  
damagesinexcessofthepurchasepriceofthe  
itemwithrespecttowhichdamagesareclaimed,  
andinnoeventshallMultiquipbeliableforloss  
of profit or good will or for any other special,  
consequentialorincidentaldamages.  
g. Decalsandpaperproducts.  
h. Itemspurchasedinkits.  
1. AReturnedMaterialAuthorizationmust  
beapprovedbyMultiquippriortoshipment.  
7. Thesenderwillbenotifiedofanymaterial  
receivedthatisnotacceptable.  
2. ToobtainaReturnMaterialAuthorization,  
alistmustbeprovidedtoMultiquipParts  
Sales that defines item numbers,  
quantities,anddescriptionsoftheitemsto  
bereturned.  
8. Such material will be held for 5 working  
days from notification, pending  
instructions. If a reply is not received  
within5days,thematerialwillbereturned  
tothesenderathisexpense.  
LIMITATIONOFWARRANTIES  
a. Thepartsnumbersanddescriptions  
mustmatchthecurrentpartsprice  
list.  
Nowarranties,expressorimplied,aremadein  
connection with the sale of parts or trade  
accessories nor as to any engine not  
manufacturedbyMultiquip.Suchwarranties  
made in connection with the sale of new,  
complete units are made exclusively by a  
statement of warranty packaged with such  
units, and Multiquip neither assumes not  
authorizes any person to assume for it any  
other obligation or liability whatever in  
connectionwiththesaleofitsproducts.Apart  
fromsuchwrittenstatementofwarranty,there  
arenowarranties,express,impliedorstatutory,  
which extend beyond the description of the  
productsonthefacehereof.  
9. Creditonreturnedpartswillbeissuedat  
dealer net price at time of the original  
purchase,lessa15%restockingcharge.  
b. The list must be typed or computer  
generated.  
10. In cases where an item is accepted for  
which the original purchase document  
can not be determined, the price will be  
basedonthelistpricethatwaseffective  
twelvemonthspriortotheRMAdate.  
c. Thelistmuststatethereason(s)for  
thereturn.  
d. The list must reference the sales  
order(s)orinvoice(s)underwhich  
theitemswereoriginallypurchased.  
11. Credit issued will be applied to future  
purchasesonly.  
e. Thelistmustincludethenameand  
phonenumberoftheperson  
requestingtheRMA.  
3. A copy of the Return Material  
Authorizationmustaccompanythereturn  
shipment.  
PAGE 76 — MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #0 (07/15/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTE PAGE  
MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #0 (07/15/02) — PAGE 77  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PARTS AND OPERATION MANUAL  
HERE'S HOW TO GET HELP  
PLEASE HAVE THE MODEL AND SERIAL NUMBER  
ON-HAND WHEN CALLING  
PARTS DEPARTMENT  
800-427-1244 or 310-537-3700  
FAX: 800-672-7877 or 310-637-3284  
6668  
SERVICE DEPARTMENT/TECHNICAL ASSISTANCE  
800-478-1244 or 310-537-3700  
FAX: 310- 537-4259  
WARRANTY DEPARTMENT  
888-661-4279, or 310-661-4279  
FAX: 310- 537-1173  
MAIN  
800-421-1244 or 310-537-3700  
FAX: 310-537-3927  
MULTIQUIP INC.  
POST OFFICE BOX 6254  
CARSON, CA 90749  
310-537-3700 • 800-421-1244  
FAX:310-537-3927  
E-MAIL:m[email protected]  
WWW:multiquip.com  
Atlanta • Boise • Dallas • Houston • Newark  
Quebec, Canada • Manchester, UK • Rio De Janiero, BR • Guadalajara, MX  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Multiquip Appliance Trim Kit MVH 304DSB User Manual
Multiquip Landscape Lighting gbe gbce User Manual
Multiquip Trash Compactor MVH 150D User Manual
Multiquip Trash Compactor QP4TH User Manual
Multiquip Webcam b46s90 User Manual