OPERATION & PARTS MANUAL
SideWinder
MODEL HS62A
CUT-OFF SAW
Revision #0 (03/20/06)
To find the latest revision of this
publication, visit our website at:
THIS MANUAL MUST ACCOMPANYTHE EQUIPMENT AT ALLTIMES.
Download from Www.Somanuals.com. All Manuals Search And Download.
Engine exhaust and some of
its constituents, and some dust created
by power sanding, sawing, grinding,
drillingandotherconstructionactivities
contains chemicals known to the State
of California to cause cancer, birth
defects and other reproductive harm.
Some examples of these chemicals are:
Leadfromlead-basedpaints.
Crystallinesilicafrombricks.
Cementandothermasonryproducts.
Arsenicandchromiumfromchemically
treatedlumber.
Your risk from these exposures varies,
dependingonhowoftenyoudothistype
of work. To reduce your exposure to
these chemicals: ALWAYS work in a
well ventilated area, and work with
approved safety equipment, such as
dust masks that are specially designed
to filter out microscopic particles.
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE PAGE
Download from Www.Somanuals.com. All Manuals Search And Download.
HS62A CUT-OFF SAW —TABLE OF CONTENTS
Carburetor Mounting Assembly .........................56-57
Carburetor Assembly .........................................58-59
Crankshaft and Piston Assembly .......................60-61
Water Kit Assembly ............................................62-63
Tools ...................................................................64-65
Recommended Diamond Blades ............................ 66
MULTIQUIP — HS62A CUT-OFF
SAW
Proposition 65 Warning ............................................. 2
Table Of Contents ..................................................... 4
Parts Ordering Procedures ....................................... 5
Safety Message Alert Symbols .............................. 6-7
Rules For Safe Operation ....................................8-11
Specifications (Saw/Engine) ................................... 12
Decal Placement ..................................................... 13
Controls & Components .....................................14-15
Blade Installation Instructions ................................. 16
Water Kit Installation Instructions ............................ 17
Blades ..................................................................... 18
Initial Start-Up/Operation ...................................19-20
Maintenance ......................................................21-25
Troubleshooting (Blade) .......................................... 26
Troubleshooting (Engine)...................................27-28
Filter Kits ................................................................. 29
Explanation of Codes in Remarks Column ............. 30
Suggested Spare Parts ........................................... 31
Terms and Conditions of Sale — Parts ................... 67
COMPONENT DRAWINGS
Muffler Assembly ...............................................32-33
Recoil Start Assembly ........................................ 34-35
Crankcase Assembly .........................................36-37
V-belt Cover (Clutch Side) Assembly .................38-39
V-Belt Cover (Pulley) Blade Guard Assembly ....40-41
Fuel Tank Assembly ...........................................42-43
Lifting Handle and Roller Assembly ...................44-45
Throttle Linkage Assembly ................................46-47
Flywheel Cover Assembly..................................48-49
Flywheel Assembly ............................................50-51
Ignition Assembly ...............................................52-53
Air Filter Assembly .............................................54-55
Specifications and part
numbers are subject to
change without notice.
PAGE 4 — HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (03/20/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
Effective:June 1st, 2005
PARTS ORDERING PROCEDURES
Ordering parts has never been easier!
Choose from three easy options:
Best Deal!
Order via Internet (Dealers Only)
Orderpartson-lineusingMultiquip’sSmartEquipwebsite!
:
If you have an MQ Account, to obtain a
Username and Password, E-mail us at:
■
■
■
View Parts Diagrams
Order Parts
PrintSpecificationInformation
To obtain an MQ Account, contact your
District Sales Manager for more information.
Use the internet and qualify for a 5% Discount
on Standard orders for all orders which include
complete part numbers.*
Gotowww.multiquip.comandclickon
to log in and save!
Order Parts
Note: Discounts Are Subject To Change
Fax your order in and qualify for a 3% Discount
on Standard orders for all orders which include
complete part numbers.*
Order via Fax (Dealers Only)
:
All customers are welcome to order parts via Fax.
Domestic (US) Customers dial:
1-800-6-PARTS-7 (800-672-7877)
Note: Discounts Are Subject To Change
Domestic (US) Dealers Call:
1-800-427-1244
Order via Phone:
Non-Dealer Customers:
International Customers should contact
their local Multiquip Representatives for
Parts Ordering information.
Contact your local Multiquip Dealer for
parts or call 800-427-1244 for help in
locating a dealer near you.
When ordering parts, please supply:
❒
❒
❒
❒
❒
❒
Dealer Account Number
❒
Specify Preferred Method of Shipment:
✓
Fed Ex/UPS
✓ DHL
Dealer Name and Address
■
■
Priority One
Ground
✓
Truck
Shipping Address (if different than billing address)
Return Fax Number
Applicable Model Number
■ Next Day
■
Second/ThirdDay
Quantity, Part Number and Description of Each Part
Unless otherwise indicated by customer, all orders are treated asStandard Orders and will ship
within24hours.WewillmakeeveryefforttoshipAirShipmentsthesamedaytheorderisreceived,
if received prior to 2PM PST. Stock Orders must be noted on fax or web order form.
NOTE
WE ACCEPT ALL MAJOR CREDIT CARDS!
HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (10/20/06) — PAGE 5
Download from Www.Somanuals.com. All Manuals Search And Download.
HS62A CUT-OFF SAW — SAFETY MESSAGE ALERT SYMBOLS
FORYOUR SAFETY AND THE SAFETY OF OTHERS!
HAZARD SYMBOLS
Safety precautions should be followed at all times when operating
this equipment. Failure to read and understand the Safety
Messages and Operating Instructions could result in injury to
yourself and others.
Lethal Exhaust Gases
Engine exhaust gases contain poisonous
carbon monoxide. This gas is colorless and
odorless, and can cause death if inhaled.
NEVER operate this equipment in a confined
area or enclosed structure that does not
provide ample free flow air.
This Owner's Manual has been
developed to provide complete
instructions for the safe and efficient
operation of the MULTIQUIP MODEL
HS62A CUT-OFF SAW. For engine
maintenance information, please refer
NOTE
to the maintenance section of this manual for data relative to its safe
operation.
Explosive Fuel
Before using this SAW, ensure that the operating individual
has read and understands all instructions in this manual.
Gasoline is extremely flammable, and its
vapors can cause an explosion if ignited. DO
NOT start the engine near spilled fuel or
combustible fluids. DO NOT fill the fuel tank
while the engine is running or hot. DO NOT
overfill tank, since spilled fuel could ignite if it
comes into contact with hot engine parts or
sparks from the ignition system. Store fuel in
approved containers, in well-ventilated areas
and away from sparks and flames. NEVER
use fuel as a cleaning agent.
SAFETY MESSAGE ALERT SYMBOLS
The three (3) Safety Messages shown below will inform you
about potential hazards that could injure you or others. The
Safety Messages specifically address the level of exposure
to the operator, and are preceded by one of three words:
DANGER, WARNING, or CAUTION.
Burn Hazards
DANGER
You WILL be KILLED or SERIOUSLY injured if you DO
NOT follow directions.
Engine components can generate extreme heat.
To prevent burns, DO NOT touch these areas
while the engine is running or immediately after
operations. NEVER operate the engine with
heat shields or heat guards removed.
WARNING
You CAN be KILLED or SERIOUSLY injured if you DO
NOT follow directions.
Rotating Parts
CAUTION
NEVER operate equipment with covers, or
guards removed. Keep fingers, hands, hair
and clothing away from all moving parts to
prevent injury.
You CAN be INJURED if you DO NOT follow directions.
PAGE 6 — HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (03/20/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
HS62A CUT-OFF SAW — SAFETY MESSAGE ALERT SYMBOLS
Accidental Starting
Respiratory Hazard
ALWAYS place the engine ON/OFF
switch in the OFF position, when the saw
is not in use.
ALWAYS wear approved respiratory protection.
Over Speed Conditions
Sight and Hearing hazard
NEVER tamper with the factory settings of the
engine governor or settings. Personal injury
and damage to the engine or equipment can
result if operating in speed ranges above
maximum allowable.
ALWAYS wear approved eye and hearing
protection.
Equipment Damage Messages
Guards and Covers In Place
NEVER operate the saw without blade guards
and covers in place. Adhere to safety
guidelines ANSI, OSHA, or other applicable
local regulations.
Other important messages are provided throughout this manual
to help prevent damage to your concrete saw, other property, or
the surrounding environment.
Rotating Blade
Rotating blade can cut and crush. Keep
hands and feet clear.
This concrete/asphalt saw, other
property, or the surrounding
environment could be damaged if
you do not follow instructions.
NOTE
HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (10/20/06) — PAGE 7
Download from Www.Somanuals.com. All Manuals Search And Download.
HS62A CUT-OFF SAW — RULES FOR SAFE OPERATION
■
NEVER touch the hot exhaust manifold,
muffler or cylinder.Allowthese parts to cool
before servicing the saw.
WARNING - ReadThis Manual
Failure to follow instructions in this manual may lead to
Serious Injury or even Death. This equipment is to be
operated by trained and qualified personnel only! This
equipment is for industrial use only.
The following safety guidelines should always be used
when operating the Multiquip HS62A Cut-off Saw.
■
■
HighTemperatures – Allow the engine to cool before adding
fuel or performing service and maintenance functions. Contact
with hot! components can cause serious burns.
SAFETY
■
DO NOT operate or service this equipment
before reading this entire manual.
The engine of this saw requires an adequate free flow of
cooling air. NEVER operate the saw in any enclosed or narrow
area where free flow of the air is restricted. If the air flow is
restricted it will cause serious
■
■
This equipment should not be operated by persons under 18
years of age.
NEVER operate the saw without proper protective clothing,
shatterproof glasses, steel-toed boots and other protective
devices required by the job.
damage to the saw's engine
and may cause injury to
people. Remember the
saw's engine gives off
DEADLY carbon monoxide
gas.
■
■
ALWAYS refuel in a well-ventilated area, away from sparks
■
■
NEVER operate this equipment when not feeling
well due to fatigue, illness or taking medicine.
and open flames.
ALWAYS use extreme caution when
working with flammable liquids.
When refueling, STOP the engine and
allow it to cool.
NEVERoperatethesawunder the influence or drugs or alcohol.
■
NEVER smoke around or near the saw.
Fire or explosion could result from fuel
vapors, or if fuel is spilled on a hot!
engine.
■
■
NEVER use accessories or attachments, which are not
recommended by Multiquip for this equipment. Damage to
the equipment and/or injury to user may result.
Manufacturer does not assume responsibility for any accident
due to equipment modifications. Unauthorized equipment
modification will void all warranties.
■
■
NEVER operate the saw in an explosive atmosphere where
fumes are present or near combustible materials. An
explosion or fire could result causing severe bodily harm
or even death.
■
■
Whenever necessary, replace nameplate, operation and
safety decals when they become difficult read.
ALWAYS move the saw at least 10 feet away from the fueling
point before starting the engine and make sure the gas cap
on the saw and the fuel can are properly tightened.
ALWAYS check the saw for loosened hardware such as nuts
and bolts before starting.
■
■
Topping-off to filler port is dangerous, as it tends to spill fuel.
NEVER use fuel as a cleaning agent.
PAGE 8 — HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (03/20/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
HS62A CUT-OFF SAW — RULES FOR SAFE OPERATION
General Safety
■
ALWAYS hold the saw with both hands when the engine is
running. Use a firm grip with thumbs and fingers encircling
the handles.
■
ALWAYS read, understand, and
follow procedures in Operator's
Manual before attempting to operate
this equipment.
■
ALWAYSkeep all parts of the body away from the cutting-off
blades when the engine is running.
■
■
ALWAYS keep the handles dry, clean and free of oil or fuel.
ALWAYS carry the saw with the engine stopped and the
muffler away from the body.
■
ALWAYS wear proper respiratory (mask), hearing and eye
protection equipment when operating the saw.
■
ALWAYS instruct bystanders on where to stand while the
saw is in operation.
■
■
ALWAYS clear the work area of unnecessary people.
NEVER allow anyone to stand in front of or behind the blade
while the engine is running.
■
■
■
ALWAYS make sure the blade is not contacting any objects
before starting the engine.
■
■
■
ALWAYS be sure the operator is familiar with proper safety
precautions and operating techniques before using the saw.
ALWAYS check for buried electrical cables before sawing. If
unsure, contact the local utilities.
ALWAYS inspect the blade, flanges and shafts for damage
before installing the blade.
ALWAYS have all service and maintenance performed by
competent trained service personnel.
ALWAYS use high-speed, reinforced, abrasive blades - 1/8"
(3.17 mm) thick (minimum) or high-speed, diamond blades
specifically rated with a maximum operating speed of at least
5,400 RPM on 14" (350 mm) or 6,200 RPM on 12" (300 mm).
■
■
■
ALWAYS clean the saw after each day’s use.
ALWAYS have a copy of this manual at the job site.
ALWAYS stop the engine before servicing, adding fuel and
oil.
■
■
ALWAYS use high-speed reinforced, abrasive blades or
high-speed, diamond blades marked with a 1" (25.4 mm)
hole for a 1" (25.4 mm) flange, or a 20 mm hole for a 20 mm
flange.
■
■
■
■
■
ALWAYS service air cleaner frequently to prevent carburetor
malfunction.
ALWAYS keep clear of rotating or moving parts while the
saw is in operation.
ALWAYS use abrasive blades or high-speed diamond blades
marked for use with gasoline-powered, hand-held, portable,
abrasive cutting-off saws.
ALWAYS maintain this saw in a safe operating condition at
all times.
■
■
ALWAYS read all safety materials and instructions that
accompany any blade used with this saw.
ALWAYS keep any inexperienced and unauthorized people
away from the saw at all times.
ALWAYS inspect each blade carefully before using it.If there
are any signs of damage or unusual wear, DO NOT USE
THE BLADE.
ALWAYS store saw properly when it is not being used.
Equipment should be stored in a clean, dry location out of
the reach of children.
■
■
■
■
ALWAYS verify the blade arbor hole matches the saw's
spindle before mounting the blade.
ALWAYS mount the blade solidly and firmly. Wrench tighten
the arbor nut.
This saw is designed for certain
applications only. DO NOT use or
modify this saw for any application
other than for which it was designed.
ALWAYS make sure the blade and flanges are clean and
free of dirt and debris before mounting the blade on the saw.
NOTE
ALWAYS use the correct blade for the type of work being
done. Check with blade manufacturer if you do not know if
blade is correct for desired application.
HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (10/20/06) — PAGE 9
Download from Www.Somanuals.com. All Manuals Search And Download.
HS62A CUT-OFF SAW — RULES FOR SAFE OPERATION
Diamond Blade Safety
■
■
NEVER leave the machine unattended while running.
■
Use appropriate steel centered diamond blades
manufactured for use on concrete saws.
NEVER run the engine without the air filter. Severe engine
damage could occur.
■
NEVER wear jewelry or loose fitting clothing that may snag
on the controls or moving parts, this can cause a serious
injury.
WARNING
■
ALWAYS inspect diamond blades before each use. The
blade should exhibit no cracks,
dings, or flaws in the steel
centered core and/or rim. Center
(arbor) hole must be undamaged
and true.
■
■
■
■
NEVER operate this saw without the blade guard, or other
protective guards in place.
NEVER stand behind or in front of the blade path while the
engine is running.
NEVER use abrasive blades that are less the 1/8" (3.17 mm)
thick.
■
Examine blade flanges for
damage, excessive wear and
cleanliness before mounting
blade. Blade should fit snugly on the shaft and against the
inside/outside blade flanges.
NEVER exceed maximum blade speed shown for each blade
size. Excessive speed could result in blade breakage.
■
■
■
■
NEVER use a damaged saw or blades.
NEVER try to stop a moving blade with your hand.
NEVER use an abrasive blade that has been dropped.
■
■
Ensure the blade is marked with an operating speed greater
than the blade shaft speed of the saw.
Only cut the material that is specified by the diamond blade.
Read the specifications of the diamond blade to ensure the
proper tool has been matched to the material being cut.
NEVER use carbide-tipped or toothed type blades of any
kind.
■
■
NEVER use segmented diamond blades unless they are
specifically designed for high-speed, hand-held saws.
■
■
ALWAYS keep blade guards in place. Exposure of the
diamond blade must not exceed 180 degrees.
NEVER place 1 inch (25.4 mm) arbor hole blades on 20 mm
flanges.
Ensure that the diamond blade does not come into contact
with the ground or surface during transportation. DO NOT
drop the diamond blade on ground or surface.
■
■
■
NEVER use the side of a cutting-off blade as a grinder.
NEVER cock, jam or wedge the blade in the cut.
■
■
The engine governor is designed to permit maximum
engine speed in a no-load condition. Speeds that exceed
this limit may cause the diamond blade to exceed the
maximum safe allowable speed.
NEVER operate the saw if the blade does not stop rotating
when the throttle trigger is released.
■
■
■
■
NEVER start cutting until you have a clear work area and
secure footing.
Ensure that the blade is mounted correctly for proper
operation.
NEVER allow other persons to be near the saw when starting,
refueling, or when the saw is operating.
Saw Transportation Safety
NEVER allow bystanders or animals in the work area while
using a cutting-off machine.
■
■
NEVER transport the saw with the blade mounted.
ALWAYS use caution when lifting and transporting this
saw.
NEVER touch a dry cutting diamond blade immediately after
use. These blades require several minutes to cool after each
cut.
■
■
ALWAYS tie-down the saw when transporting.
ALWAYS use caution and follow the instructions when
loading and unloading the saw.
■
■
■
NEVER use damaged or worn blade flanges. Discard any
damage or worn saw parts.
NEVER allow blade exposure from the guard to be more
than 180 degrees.
NEVER operate this saw without both hands on the handles.
PAGE 10 — HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (03/20/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
HS62A CUT-OFF SAW — RULES FOR SAFE OPERATION
EMERGENCIES
■
ALWAYS know the location of
the nearest fire extinguisher.
■
■
ALWAYS know the location of the
nearest first aid kit.
In emergencies always know the location of the
nearest phone or keep a phone on the job site.
Also know the phone numbers of the nearest
ambulance, doctor, and fire department. This
information will be invaluable in the case of an
emergency.
HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (10/20/06) — PAGE 11
Download from Www.Somanuals.com. All Manuals Search And Download.
HS62A CUT-OFF SAW — SPECIFICATIONS
Table 1. HS62A Cut-off Saw Specifications
50 x 33 x18 in.
(1270 x 838 x 457 mm)
Dimension (Shipping) LxWxH
Weight
22.9 lbs. (10.4 kg)
14 in. (356 mm)
5 in. (127 mm)
1 in. (20 mm)
Reversible
Blade Size
Maximum Cut Depth
Arbor Size
Cutting Arm
Table 2. HS62A Power Source Specifications
Engine Type
Two-Stroke, Single Cylinder, Air cooled
3.86 cu. in (63.3 cc.)
5,100 RPM
Displacement
Maximum Spindle Speed
Engine Speed
Idle Speed
10,000 RPM
2,500 RPM
29.13 x 8.27 x 15.75 in.
(740 x 210 x 400 mm)
Dimensions (LxWxH)
Fuel Tank Capacity
Fuel/Oil Mix Ratio
Starting Method
.17 Gallons. (.65 Liters)
See Figure 13, Page 19
Recoil Start
Electronic
Type
Speed Controlled
.014 in. (.35 mm)
Champion/NGK
RCJ7Y/BPR6A
.020 (0.5 mm)
Walbro
Ignition
Gap
Manufacturer
Type
Spark Plugs
Gap
Manufacturer
Model
HD207
Carburetor
Diaphragm/Semi-Fixed
Jet
Type
PAGE 12 — HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (03/20/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
HS62A CUT-OFF SAW — DECAL PLACEMENT
Machine Operation And Safety Decals
The HS62A CUT-OFF SAW is equipped with a number of
operation and safety decals (Figure 1). Should any of these
decals become unreadable, replacements can be obtained from
your dealer.
P/N DCL 230
P/N DCL 231
P/N DCL 232
P/N DCL 233A
P/N DCL 161
Figure 1. Safety Decals
HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (10/20/06) — PAGE 13
Download from Www.Somanuals.com. All Manuals Search And Download.
HS62A CUT-OFF SAW — CONTROLS & COMPONENTS
3
1
2
4
12
11
9
5
8
7 6
10
Figure 2. HS62A Cut-off Saw Components 1
Figures 2 and 3 shows the location of the basic controls or
components for the Multiquip Model HS62A Cut-off Saw. Listed
below is a brief explanation of each control or component.
1.
Air Filter – Prevents dirt and debris from entering the engine
air intake. Check filter periodically and keep cleaned or
replace when necessary. NEVER run engine with a dirty
air filter.
7.
8.
RollerWheel – Allows for easy free movement of the saw
when cutting on a flat surface.
V-belt Cover (Clutch) – Unscrew these 2 nuts to remove
the clutch V-belt cover. NEVER operate the saw with this
cover removed. It may be necessary to remove the pulley
cover first before this cover can be removed.
2. Muffler – Used to reduce noise and emissions. NEVER!
touch muffler when engine is running. Allow engine to cool
down.This component gets extremely hot!
9.
Decompression Valve – Push inward when starting
3.
Guard Adjustmet Knob – Allows for the adjustment of
the blade guard. Turn this knob clockwise to tighten,
counter-clockwise to loosen.
engine.
10. Choke Lever – Used in the starting of a cold engine, or in
cold weather conditions. The choke enriches the fuel
mixture.
4.
5.
Pulley Lock Pin Hole – Insert a phillips head screw driver
or similar tool into this hole to prevent the pulley from rotating.
11. Rear Handle – When starting engine, place right foot onto
rear handle base. For normal operation always place one
hand on the rear handle and the other hand on the upper
handle.Always use two hands when operating the saw.
V-beltTensioning Cam – Allows for the adjustment of the
V-belt. To tighten V-belt turn clockwise, to slacken turn
counterclockwise.
6.
V-belt Cover (Pulley) – Unscrew these 3 nuts to remove
the pulley V-belt cover. NEVER operate the saw with this
cover removed.
12. Engine ON/OFF Switch – ON position permits engine
starting, OFF position stops engine operation.
PAGE 14 — HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (03/20/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
HS62A CUT-OFF SAW — CONTROLS & COMPONENTS
14
13
16
15
22
21 20 19
18
17
Figure 3. HS62A Cut-off Saw Components 2
13. Blade Guard – Covers saw blade.
18. Fuel Filler Cap – Remove this cap to add mixed fuel
(requires a 50:1 mixture) to the fuel tank.This saw uses a
2-stroke engine.Make sure fuel cap is tightened securely.
DO NOT over fill. See Figure 13 for correct fuel to oil mixture.
14. Front Handle – When lifting or carrying of the saw is
required, use this handle.
15. Throttle Lock Lever – Using your thumb, press this lever
downward and squeeze the trigger lever to lock the throttle
in place. Use this option only to aid starting. Squeeze the
trigger lever again to unlock the throttle.
19. Recoil Starter (pull rope) – Manual-starting method. Pull
the starter grip until resistance is felt, then pull briskly and
smoothly.
20. Blade Shaft Nut – Loosen to remove the cutting blade
16. Throttle Trigger Lock-out – Press this lever downward
from the outer and inner flanges.
to allow throttle trigger activation.
21. Cutting Blade – Use appropriate type blades for desired
17. Throttle Trigger Lever – Squeeze this lever to start the
saw blade rotation. Release the trigger lever to stop the
saw blade rotation. This lever is to be used in conjunction
with either the throttle lock or variable throttle levers.
cutting application.
22. Spark Plug – Provides spark to the ignition system. Set
spark plug gap to 0.02 inch (0.5 mm). Clean spark plug
once a month.
HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (10/20/06) — PAGE 15
Download from Www.Somanuals.com. All Manuals Search And Download.
HS62A CUT-OFF SAW — BLADE INSTALLATION INSTRUCTIONS
The Multiquip Side Winder Cut-Off Saw comes with aTool Kit
(Figure 4) that assists you with day to day operations.You will
need these tools for the assembly of your saw.
Item Gis a versatile screwdriver/wrench that accommodates
common bolt/screw and nut head sizes of your saw.
Item
allen screws.
is the wrench necessary to accommodate various
H
Figure 4. Tool Kit
Blade Installation Procedure
STEP 1
STEP 3
Chose the proper blade arbor side of the inner flange (to match
For proper installation, first remove the blade shaft nut
X,
your cutting blade arbor) and place this selected side to the
outer flange
, and inner “dual-arbor” flange
.
Y
Z
blade shaft
.
[
Figure 5. Inner and Outer Flanges (Removal)
STEP 2
A dual sided, “dual-arbor” inner flange
Figure 7. Selecting the Proper Blade Arbor
STEP 4
accommodates either
Match the arbor side to the dimension of your blade arbor and
“sandwich” between the inner and outer flanges. Tighten the
blade shaft nut Xsecurely to hold the blade in place.
Z
a 20 mm or 1-inch arbor hole for operator safety and convenience.
The outer flange fits on top of the cutting blade.
Y
Figure 6. Inner and Outer Flanges (Placement)
Figure 8. Securing the Cutting Blade
PAGE 16 — HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (03/20/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
HS62A CUT-OFF SAW —WATER KIT INSTALLATION INSTRUCTIONS
Contents ofWater Kit
The contents of the Water Kit cannot be purchased seperately.
See Water Kit Assembly in Parts Section of this manual for
Water Kit part number.
Hose Clamp G
Socket Head Cap Screw w/Washer H
Quick Disconnect Fitting I
Water Hose J
Hex KeyTool K(Included withTool Kit)
Figure 9. Water Kit Parts
PlasticTies L
Wet Air Filter Canister M(Sold Seperately)
Water Kit Installation Procedure
ꢀ
Connect the Quick Disconnect Fitting Ito the
single end of the Water Hose J.
Snap fit the Water Hose Outlets Jto the Holes in the
Blade Guard .Orient the Water Hose Jthrough the
Front Handle.
!
Loop the Hose Clamp Garound theWater Hose
J
and fasten the clamp to the Roller Bar Support Arm
using the Socket Head Cap Screw w/Washer H, and
Hex KeyTool K.
Figure 10. Water Kit Assembly Points
"
#
Use the PlasticTies Las preferred to further secure
the hose fittings and water hose to the saw.
When using the Water Kit option for your saw, the Dry Air
Filter Canister MUST be replaced with the Wet Air Filter
Canister M(See Air Filter Kit Assembly in Parts
Section of this manual).
Figure 11. Wet Air Filter Canister
HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (10/20/06) — PAGE 17
Download from Www.Somanuals.com. All Manuals Search And Download.
HS62A CUT-OFF SAW — BLADES
PREPARATION / PRE-INSPECTION
1. Read and fully understand this manual,
the safety instructions in particular, and
the engine manufacturer's manual
supplied with the saw.
2. Select the correct blade for each application. If abrasive
blades are used, MAKE CERTAIN they are designed for
use on a concrete floor saw. They must be reinforced and
have a hole for the driving pin. When wet cutting with an
abrasive blade, MAKE CERTAIN the blade is intended for
wet cutting. Water will destroy a dry cut abrasive blade.
Some diamond blades require water cooling and failure to
do so will destroy them almost immediately. Other diamond
blades can be used with or without water.
Figure 12. Diamond Blade
2. Edge of the Steel Core - Check the diameter edge for
discoloration (blue oxidation) indicating an overheating
condition caused by insufficient cooling water/air.
Overheating of blades may lead to loss of core tension and/
or increase the possibility for blade failure. Make sure the
steel core's width is uniform about the rim of the blade, and
not succumbing to an "under-cutting" condition brought
about by highly abrasive material or improper under-cutting
core protection
3. Handle all blades with care and NEVER use a damaged
blade. NEVER use an abrasive blade that has been
dropped.
BLADES
3. Directional Arrow - Ensure that the blade is oriented
properly on the blade shaft for sawing. Reference the
directional arrow on the blade and place it so the direction
of rotation "downcuts" with the turn of the shaft.
Saw blades, or cutting disks, are available in either an abrasive
design or as diamond blades. Either blade will work on the
HS62ACUT-OFFSAW,however,diamondbladesare recommended.
Ask your dealer about your specific cutting application.
4. Diamond Segment or Rim - Ensure there are no cracks,
dings, or missing portions of the diamond segment/rim. DO
NOT use a blade that is missing a segment or a portion
of the rim. Damaged and /or missing segments/rims may
cause damage to your saw or injury to the user or others in
the operating area.
SAW BLADE INSPECTION
WARNING
Failure to thoroughly inspect the diamond
blade (Figure 12) for operational safety
could result in damage to the blades or
the saw and may cause injury to the user
or others in the operating area.
5. Specifications - Ensure that the blade specifications, size,
and diameter properly match up to sawing operations.
Utilizing a blade not matched properly to the task may result
in poor performance and/or blade damage.
6. Arbor Hole - It is essential that the arbor hole diameter
properly matches the blade, and that it is free from distortion.
Correct blade flanges (collars) must be used. The inside
face of the flanges must be clean and free of debris. An out-
of-round arbor condition will cause damage to the blade
and the saw.
1. Stress Relief Holes (Gullets) - Check the steel core for
cracks that may have propagated from the slots and/or
gullets. Cracks indicate extreme fatigue failure and if sawing
continues, catastrophic failure will occur.
7. MAX RPM - This RPM reference is the maximum safe
operating speed for the blade selected. NEVER exceed the
max RPM on the diamond blade. Exceeding the maximum
RPM is dangerous and may cause poor performance and
may damage the blade.
PAGE 18 — HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (03/20/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
HS62A CUT-OFF SAW — INITIAL START-UP/OPERATION
INITIAL START-UP
CAUTION
DO NOT attempt to operate the saw until the Safety, General
Information and Inspection sections of this manual have been
read and thoroughly understood. Depending on engine
manufacturer, operating steps may vary. See engine
manufactures operating manual.
CAUTION
Figure 13. Fuel to Oil Mixture
NEVER operate the saw in a confined area
or enclosed area structure that does not
provide ample free flow of air.
For correct fuel to oil mixture, add 2.6 fl. oz
(29.6 ml) of 2-stroke motor oil to 1 gallon (3.8
liters) of premium 92 octane unleaded
gasoline. For a 5 gallon can of premium
unleaded gasoline add 13 fl. oz (384 ml) of
2-stroke motor oil.
NOTE
ALWAYS wear approved eye and
hearing protection before operating the
saw.
A bottle ( 2.6 fl. oz) of smokeless 2-stroke motor oil cannot be
purchased separately.Only a case of 36 individual bottles can
be purchased. When ordering use Multiquip P/N 00325.
NEVER place hands or feet inside the belt
guard or blade guard while the engine is
running. ALWAYS shut the engine down
before performing any kind of
maintenance service on the saw.
Starting
1. Place the engine ON/OFF switch in the ON position
2. Using your thumb, press down on the throttle lock lever,
while squeezing the throttle trigger.This will lock the throttle
in the half-throttle position.
Explosive Fuel
Fuel Check
3. Pull the choke lever all the way out to the CLOSED position.
4. Pull the decompression button inward.
Motor fuels are highly flammable and can be
dangerous if mishandled. DO NOT smoke
while refueling. DO NOT attempt to refuel the
saw if the engine is hot! or running.
5. Place the saw on level ground. Make sure the saw blade is
free to rotate and will not come into contact with any foreign
objects.
1. Remove the fuel cap located on the side of the saw.
6. Hold the front handle firmly with the left hand and put your
right foot onto the base of the rear handle.
2. Visually inspect to see if fuel level is low. If fuel is low,
replenish with fuel oil mixture as shown in Figure 13.
3. When refueling, be sure to use a strainer for filtration. DO
NOT top-off fuel. Wipe up any spilled fuel.
The CLOSED position of the choke lever
enriches the fuel mixture for starting a COLD
engine. The OPEN position provides the
correct fuel mixture for normal operation after
starting, and for restarting a warm engine.
This saw uses a 2-stroke engine which
NOTE
requires a mixture of premium 92 octane
unleaded gasoline and smoke free 2-stroke
motor oil. See Figure 13.
NOTE
HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (10/20/06) — PAGE 19
Download from Www.Somanuals.com. All Manuals Search And Download.
HS62A CUT-OFF SAW — INITIAL START-UP/OPERATION
7. Graspthestartergrip andslowlypullitout.Theresistance
becomesthehardestatacertainposition,correspondingto
thecompressionpoint.Pullthestartergripbrisklyandsmoothly
forstarting.
Mark the cutting line clearlyand always
saw in a STRAIGHT LINE ONLY.
NOTE
8. Iftheenginehasstarted,slowlyreturnthechokelever tothe
"OPEN"position.Iftheenginehasnotstartedrepeatsteps
1 through 9.
4. When the end of the cut has been reached, raise the blade
out of the cut .
9. Squeezethethrottlelevertriggertoreleaseitfromthehalf-
throttle position.
5. Ifcuttingiscomplete,turntheengineoffandwaitfortheblade
tostoprotating.
10. Before the saw is placed into operation, run the engine for
severalminutes. Checkforfuelleaks,andnoisesthatwould
associate with a loose guards and/or covers.
Shut-down
1. Let the engine idle for 3-5 minutes.
2. Place the engine ON/OFF switch to the OFF position
3. Wait for the blade to stop spinning before handling the saw.
OPERATION
WARNING
ALWAYS cut with the saw at FULLTHROTTLE. Attempting
to cut with the saw at less than full throttle could cause the
blade to bind or stop abruptly in the slab resulting in serious
injury to the operator or others in the area.
4. DO NOT touch the cutting blade it is very hot!, allow it to
cool, severe burn condition exists.
WARNING
ALWAYS keep clear of rotating or moving parts while
operating this equipment.
2. Tobeginsawing,lowertherotatingbladeallowingittocutto
thepresetdepth.
3. When blade has reached full cutting depth, slowly walk
behindthesawataratethatwillallowtheenginetooperate
withoutlosingoptimumRPM.
CAUTION
DO NOT try to cut faster than the blade will allow. Cutting
too fast will cause the blade to rise up out of the cut. Improper
cutting rate can decrease the life of the engine and blades.
PAGE 20 — HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (03/20/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
HS62A CUT-OFF SAW — MAINTENANCE
V-Belt Changing Procedure
N
Remove the 2 hex nuts Land hex screw and washer Mto
gain access to the V-belt on the clutch side. Remove V-belt
cover
.
T
Figure 14. Belt Guard Cover Removal
Remove the 2 hex nuts Jand hex screw and guard adjustment
knob Ito gain access to theV-belt on the spindle side. Remove
the Cover Guard K.
Figure 15. Re-Installing Cover Guard
Using the provided wrench, loosen the three nuts
the tension on theV-belt, then turn the V-beltTensioning Cam
to reduce
M
Luntil theV-belt is completely slacked.
Figure 16. V-BeltTensioning
Remove the V-belt Pfrom the clutch and spindle pulleys.
Install the newV-belt around both pulleys.It is essential that the
drive V-belt is properly positioned around both the clutch and
spindle pulleys.
Figure 17. DriveV-Belt
HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (10/20/06) — PAGE 21
Download from Www.Somanuals.com. All Manuals Search And Download.
HS62A CUT-OFF SAW — MAINTENANCE
V-Belt Changing Procedure (continued)
Re-tension the V-belt by turning the belt tensioning cam O.
TheV-belt should remain in tension.
Fully tighten the three nuts Nthat lock theV-belt into the proper
tensioning position.
Figure 18. Reversing the Cutting Arm
covers. Fully tighten
T
Re-install the guard Kand V-belt
the two cap screws J
and reinstall the adjustment knob I.
N
Figure 19. Re-Installing Cover Guard
PAGE 22 — HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (03/20/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
HS62A CUT-OFF SAW — MAINTENANCE
Reversing the Cutting Arm Procedure
This assembly procedure permits the operator to reorient the cutting blade closer to a wall, column
and/or object.
NOTE
The Multiquip Side Winder Cut-Off Saw comes with aTool Kit
(Figure 16) that assist you with day to day operations.You will
need these tools for the maintenance of your saw.
Item Gis a versatile screwdriver/wrench that accommodates
common bolt/screw and nut head sizes of your saw.
Item
is the wrench necessary to accommodate various allen
H
screws.
Figure 20. Tool Kit
This position displays the cutting blade on the inside (center)
cutting position.To reverse the blade position continue with the
following steps:
Remove the following items from the Cutting Arm Assembly
to expose theV-belt:
■
Guard Adjustment Knob I
■
Two Cap Screws J
■
Cover Guard K
Figure 21. Inside Center Cutting Position
Loosen the belt tensioning cam
and remove the three
L
.This will take tension off the V-belt, and permit you to
nuts
M
reverse the cutting arm.
Figure 22. BeltTensioning Cam
HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (10/20/06) — PAGE 23
Download from Www.Somanuals.com. All Manuals Search And Download.
HS62A CUT-OFF SAW — MAINTENANCE
Reversing the Cutting Arm Procedure (continued)
Reverse the cutting arm 180 degrees as shown in the Figure
23, and re-tension the V-belt by turning the belt tensioning
cam O.TheV-belt should remain in tension.
Fully tighten the three nuts Nthat lock theV-belt into the proper
tensioning position.
Figure 23. Reversing the Cutting Arm
Re-attach the cover guard Kwith the 2 cap screws
J,
I.
and reconnect the guard adjustment knob
Figure 24. Re-attaching Cover Guard
PAGE 24 — HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (03/20/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
HS62A CUT-OFF SAW — MAINTENANCE (AIR/FUEL FILTER)
Air/Fuel Filter Maintenance Procedures
Check the fuel filter G located inside the fuel tank periodically
for dirt/debris build up. It is recommended to change the fuel filter
every 50 tanks of fuel.
This engine is a 2-stroke gasoline engine requiring a specific
fuel to oil mixture of 50:1(2%). It is recommended to use an
unleaded gasoline rated at 92 octane (premium) with an oil for
use on 2-stroke engines only.See Figure 13.
Figure 25. Fuel Filter
It is highly recommended to keep a supply of spare pre-filters
on hand.Maintaining the foam pre -filter, and regular exchanges
will prolong the life of the main filter element.
Every 8 hours of operation, remove the pre-air cleaner cover
and wash the foam pre-cleaner Hin warm fresh soapy
I
water. Let dry thoroughly. When dry, completely coat the filter
with only an approved foam filter oil.
Figure 26. Pre-Filter
Every 8 hours of operation, remove the covers Iand J
and inspect the main filter element. Clean the main filter
element Kby vigorously shaking out and dusting off with a
soft brush. DO NOT air blast clean this element with compressed
gas.
The main filter element should be replaced after three pre filter
changes
Figure 27. Main Filter Element
Every 8 hours of operation, inspect the supplementary filter
element
. Clean the supplementary filter element
by
L
L
vigorously shaking out and dusting off with a soft brush. DO
NOT air blast clean this element with compressed gas.
The supplementary filter element should be replaced after
three pre filter changes.
Figure 28. Supplementary Filter
HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (10/20/06) — PAGE 25
Download from Www.Somanuals.com. All Manuals Search And Download.
HS62A CUT-OFF SAW — TROUBLESHOOTING (BLADE)
TABLE 3. BLADE TROUBLESHOOTING
SYMPTOM
POSSIBLE PROBLEM
SOLUTION
Consult Dealer or Multiquip for correct blade. Try cutting
very soft material (sandstone, silica brick, cinder block) to
"Redress" the blade.
Blade too hard for the material being
cut?
Engine torque diminished because of
loose V-belt?
Tighten and/or replace V-Belts.
Check throttle setting.
Blade slows or stops cutting.
Insufficient engine power?
Check that the blade is properly oriented and rotational
arrow points in a "Down-Cutting" direction.
Improper direction of rotation?
Check that the blade & flange pin are properly installed on
the blade shaft.
Blade is slipping on the blade shaft?
Blade being used on misaligned saw?
Check blade shaft bearings and alignment integrity.
Blade is excessively hard for the
material being cut?
Check specification of the blade with the material being
cut. Consult Dealer or Multiquip for information.
Ensure blade surface feet per minute speed (SFPM) is
approximately 6,000.
Blade being used at improper RPM?
Blade does not cut straight
and/or true.
Blade improperly mounted on arbor
shoulders and flanges?
Ensure blade is properly affixed on the blade shaft.
Excessive force applied to blade while
cutting?
DO NOT force the blade in the cut. Apply a slow and
steady pace when sawing.
Consult Dealer or Multiquip for correct blade. Try cutting
very soft material (sandstone, silica brick, cinder block) to
"Redress" the blade.
Blades too hard for the material being
cut?
Blade improperly mounted on arbor
shoulders and flanges?
Ensure blade is properly affixed on the blade shaft.
Ensure proper flow & volume of water is provided for wet
cutting blades. Ensure sufficient cooling air is circulated
about a dry cutting blade.
Blade not receiving enough cooling
water or air?
Blade discoloring, crackling
and/or wearing excessively.
Arbor hole out of round?
Ensure blade is properly affixed on the blade shaft.
Incorrect blade chosen for material
being cut?
Check specification of the blade with the material being
cut. Consult Dealer or Multiquip for information.
Excessive force applied to blade while
cutting?
DO NOT force the blade in the cut. Apply a slow and
steady pace when sawing.
PAGE 26 — HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (03/20/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
HS62A CUT-OFF SAW — TROUBLESHOOTING (ENGINE)
TABLE 4. TROUBLESHOOTING (ENGINE)
SYMPTOM
POSSIBLE CAUSE
SOLUTION
Check gap, insulation or
replace spark plug.
Spark plug bridging?
Carbon deposit on spark plug?
Clean or replace spark plug.
Difficult to start, "fuel is available, but no
SPARK at spark plug".
Short circuit due to deficient spark plug
insulation?
Check spark plug insulation,
replace if worn.
Improper spark plug gap?
Ignition coil defective?
Set to proper gap.
Replace ignition coil.
Check switch wiring, replace
switch.
ON/OFF switch is shorted?
Difficult to start, "fuel is available, and
SPARK is present at the spark plug".
Set correct spark gap and
clean points.
Improper spark gap, points dirty?
Spark plug wire broken or short circuiting?
Wrong fuel type?
Replace defective spark plug
wiring.
Flush fuel system, and replace
with correct type of fuel.
Water or dust in fuel system?
Air cleaner dirty?
Flush fuel system.
Clean or replace air cleaner.
Close Choke.
Difficult to start, "fuel is available, spark
is present and compression is normal".
Choke Open?
Suction/exhaust valve stuck or protruded?
Re-seat valves.
Replace piston rings and/or
piston.
Piston ring and/or cylinder worn?
Difficult to start, "fuel is available, spark
is present and compression is low".
Cylinder head and/or spark plug not
tightened properly?
Torque cylinder head bolts and
spark plug.
Head gasket and/or spark plug gasket
damaged?
Replace head and/or spark plug
gaskets.
Fuel not available in fuel tank (tank empy)? Fill with correct type of fuel.
Fuel filter clogged?
Replace fuel filter.
No fuel present at the carburetor.
Fuel tank cap breather hole clogged?
Air in fuel line?
Clean or replace fuel tank cap.
Bleed fuel line.
HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (10/20/06) — PAGE 27
Download from Www.Somanuals.com. All Manuals Search And Download.
HS62A CUT-OFF SAW — TROUBLESHOOTING (ENGINE)
TABLE 4. TROUBLESHOOTING (ENGINE, CONTINUED)
SYMPTOM
POSSIBLE CAUSE
Air cleaner not clean?
SOLUTION
Clean or replace air cleaner.
Rebuild carburetor.
"Weak in power" compression is proper
and does not misfire.
Defective spark plug?
Clean or replace spark plug.
Set to proper gap.
Improper spark plug gap?
Flush fuel system and replace
with correct type fuel.
Water in fuel system?
"Weak in power" compression is proper
but misfires.
Ignition coil defective?
Dirty spark plug?
Replace ignition coil.
Clean or replace spark plug.
Flush fuel system, and replace
with correct type of fuel.
Wrong fuel type?
Replace with correct type of
spark plug.
Engine overheats.
Spark plug heat value improper?
Cooling fins dirty?
Clean cooling fins.
Check entire fuel system for
leaks or clogs.
Rotational speed fluctuates.
Recoil starter malfunction.
Fuel flow restricted?
Recoil mechanism clogged with dust and
dirt?
Clean recoil assembly with soap
and water.
Spiral spring loose?
Consult Dealer.
PAGE 28 — HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (03/20/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
HS62A CUT-OFF SAW — FILTER KITS
For Side Winder HS Series Cut-Off Saws
HS62A
DRY FILTER KITS
HS62FK1A
HS62FK5A
HS62FK10A
[ Includes 1 ea.]
[ Includes 5 ea.]
[ Includes 10 ea.]
HS52020270R- Foam Filter
HS018600125R- Paper Filter
HS018600056AR - Inner Filter
HS52020270R- Foam Filter
HS018600125R - Paper Filter
HS018600056AR - Inner Filter
HS52020270R- Foam Filter
HS018600125R - Paper Filter
HS018600056AR - Inner Filter
WET FILTER
* Replaces DRY Air Filter CanisterWhen UsingWater &
StandardWater Kit (provided)
HS099900778A
[ Includes 1 ea.]
HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (10/20/06) — PAGE 29
Download from Www.Somanuals.com. All Manuals Search And Download.
HS62A CUT-OFF SAW — EXPLANATION OF PARTS SECTION REMARKS
The following section explains the different symbols and remarks QTY. Column
used in the Parts section of this manual. Use the help numbers
found on the back page of the manual if there are any questions.
Numbers Used - Item quantity can be indicated by a number,
a blank entry, or A/R.
A/R (As Required) is generally used for hoses or other parts
that are sold in bulk and cut to length.
The contents and part numbers listed in the parts section are
A blank entry generally indicates that the item is not sold
separately. Other entries will be clarified in the “Remarks”
Column.
subject to change without notice. Multiquip does not
guarantee the availibility of the parts listed.
Sample Parts List:
REMARKS Column
NO. PART NO. PART NAME
QTY. REMARKS
Some of the most common notes found in the “Remarks”
Column are listed below. Other additional notes needed to
describe the item can also be shown.
1
2
2
3
4
12345
BOLT ....................... 1.... INCLUDES ITEMS W/
WASHER, 1/4 IN. ........... NOT SOLD SEPARATELY
WASHER, 3/8 IN. .... 1.... MQ-45TONLY
HOSE .................... A/R.. MAKE LOCALLY
BEARING ................ 1.... S/N2345B AND ABOVE
*
*
*
12347
12348
12349
Assembly/Kit - All items on the parts list with the same unique
symbol will be included when this item is purchased.
Indicated by:
“INCLUDES ITEMS W/(unique symbol)”
NO. Column
Unique Symbols - All items with same unique symbol
Serial Number Break - Used to list an effective serial number
range where a particular part is used.
( , #,
+
, %, or >) in the number column belong to the same
*
assembly or kit, which is indicated by a note in the “Remarks”
column.
Indicated by:
“S/N XXXXX AND BELOW”
“S/N XXXX AND ABOVE”
“S/N XXXX TO S/N XXX”
Duplicate Item Numbers - Duplicate numbers indicate
multiple part numbers are in effect for the same general item,
such as different size saw blade guards in use or a part that
has been updated on newer versions of the same machine.
Specific Model Number Use - Indicates that the part is used
only with the specific model number or model number variant
listed. It can also be used to show a part is NOT used on a
specific model or model number variant.
When ordering a part that has more
than one item number listed, check
the remarks column for help in
determining the proper part to order.
NOTE
Indicated by:
“XXXXX ONLY”
“NOT USED ON XXXX”
“Make/Obtain Locally” - Indicates that the part can be
purchased at any hardware shop or made out of available
items. Examples include battery cables, shims, and certain
washers and nuts.
PART NO. Column
Numbers Used - Part numbers can be indicated by a number,
a blank entry, orTBD.
TBD (To Be Determined) is generally used to show a part that
has not been assigned a formal part number at time of
publication.
“Not Sold Separately” - Indicates that an item cannot be
purchased as a separate item and is either part of an
assembly/kit that can be purchased, or is not available for
sale through Multiquip.
A blank entry generally indicates that the item is not sold
separately or is not sold by Multiquip. Other entries will be
clarified in the “Remarks” Column.
PAGE 30 — HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (03/20/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
HS62A CUT-OFF SAW — SUGGESTED SPARE PARTS
SUGGESTED SPARE PARTS
HS62A SIDEWINDER CUT-OFF SAW
1 to 3 Units
Qty.
P/N
Description
1 ............ HS52022011A....... STARTER ASSEMBLY
3 ............ HS098000079R .... ROPE, STARTER
1 ............ HS50140060 ......... HANDLE, ROPE
1 ............ HS098000060A ..... SPRING & CASE, STARTER
6 ............ HS3055118 ........... SPARK PLUG
1 ............ HS50012023AR .... CLUTCH ASSEMBLY
1 ............ HS52022005 ......... FUEL CAP, W/O-RING
3 ............ HS50010218 ......... FILTER, FUEL
1 ............ HS52010092 ......... THROTTLE TRIGGER LEVER
1 ............ HS52010077 ......... THROTTLE LOCK LEVER
1 ............ HS52020037 ......... CHOKE LEVER
1 ............ HS52010022A....... COVER, BELT GUARD
3 ............ HS3918013 ........... WASHER, BELT COVER
3 ............ HS3914010 ........... NUT, BELT COVER
3 ............ HS52020020 ......... V-BELT
2 ............ HS018600235 ....... FLANGE, ARBOR
2 ............ HS018600236A ..... FLANGE, ARBOR
2 ............ HS52010177 ......... SCREW AND WASHER, ARBOR
2 ............ HS52010062A....... KNOB, ADJ. GUIDE
2 ............ HS3833080 ........... WASHER, ADJ.GUIDE
2 ............ HS52010045 ......... SPACER, ADJ.GUIDE
2 ............ HS52010013 ......... LOCK, GUIDE BLADE GUARD
1 ............ HS52012024B....... FLANGE, PRE-FILTER CAP
1 ............ HS52010014B....... SUPPORT FILTER
2 ............ HS3802002A......... SCREW, FILTER SUPPORT
1 ............ HS330000010 ....... O-RING, FLANGE PRE-FILTER
1 ............ HS018600090A ..... GASKET, AIR FILTER LOWER
18 .......... HS018600125R .... AIR FILTER
6 ............ HS018600056AR .. FILTER, AIR INNER
18 .......... HS52020270R ...... PRE-FILTER, FOAM
3 ............ HS4191240 ........... TOOL KIT
3 ............ HS099900778A ..... WET, AIR FILTER
3 ............ HS52010082 ......... BREATHER ASSEMBLY
1 ............ 00325 .................... CASE, OIL 2-STROKE NON-SMOKE - 36 BOTTLES
The contents of this parts
catalog are subject to change
without notice.
NOTE
HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (10/20/06) — PAGE 31
Download from Www.Somanuals.com. All Manuals Search And Download.
HS62A CUT-OFF SAW — MUFFLER ASSY.
MUFFLER ASSY.
PAGE 32 — HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (03/20/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
HS62A CUT-OFF SAW — MUFFLER ASSY.
MUFFLER ASSY.
NO.
PART NO.
HS3801052
HS3033074
PART NAME
SCREW
WASHER
COVER, MUFFLER
SCREW
SCREW
WASHER
DEFLECTOR, MUFFLER
SCREEN
MUFFLER ASSEMBLY ............................. 1 ......... INCLUDES ITEMS W/
SCREW
QTY.
REMARKS
1
*
2
*
3
*
4
*
5
*
6
*
7
*
8
*
9
3
5
1
2
2
2
1
1
HS50010145
HS3801045
HS005100913B
HS3833073
HS50010198
HS50010197
HS52010441
HS097000092A
HS50010058A
*
10
11
2
1
*
GASKET, MUFFLER
HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (10/20/06) — PAGE 33
Download from Www.Somanuals.com. All Manuals Search And Download.
HS62A CUT-OFF SAW — RECOIL START ASSY.
RECOIL START ASSY.
PAGE 34 — HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (03/20/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
HS62A CUT-OFF SAW — RECOIL START ASSY.
RECOIL START ASSY.
NO.
PART NO.
PART NAME
QTY.
REMARKS
14
HS50140060
HS098000079R
HS098000060A
HS3960017
HANDLE, STARTER ROPE
ROPE, STARTER
SPRING AND CASE, STARTER
SCREW
1
1
1
4
1
1
1
1
1
4
*
15
*
16
*
17
*
18
HS3960116
HS50140055
HS3918006
HS52010439B
HS3908036
HS097000092A
HS52022011A
HS52010410
HS50140056
HS52010404
SCREW
COVER
WASHER
PULLEY, STARTER
SCREW
*
19
*
20
*
21
*
22
*
23
SCREW
24
STARTER ASSEMBLY .............................. 1 ......... INCLUDES ITEMS W/
CAP
CAP
SPACER
*
25
1
1
1
*
26
*
27
*
HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (10/20/06) — PAGE 35
Download from Www.Somanuals.com. All Manuals Search And Download.
HS62A CUT-OFF SAW — CRANKCASE ASSY.
CRANKCASE ASSY.
PAGE 36 — HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (03/20/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
HS62A CUT-OFF SAW — CRANKCASE ASSY.
CRANKCASE ASSY.
NO.
3
11
12
16
18
PART NO.
PART NAME
PLATE
GROMMET
CAP
QTY.
REMARKS
HS52010312
HS52020014
HS52020040
HS50010047AR
HS52020273
HS3034012
1
1
1
1
GASKET, CRANKCASE
CRANKCASE W/ BEARING ASSY ........................ 1 ......... INCLUDES ITEMS W/
BEARING, CRANKCASE
CAP
GROMMET
WASHER
SCREW
BAR STUD, CRANKCASE
SCREW
*
19
20
2
1
1
7
2
2
4
1
1
1
2
*
HS52020013
HS50010029
HS3833073
HS006100303
HS097000080BR
HS3801015
HS005100987
HS097000057
HS52020037
HS3023008
21
22
23
24
26
28
30
31
SCREW
GROMMET
CHOKE LEVER
PIN
37
*
HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (10/20/06) — PAGE 37
Download from Www.Somanuals.com. All Manuals Search And Download.
HS62A CUT-OFF SAW —V-BELT COVER (CLUTCH SIDE) ASSY.
V-BELT COVER (CLUTCH SIDE) ASSY
PAGE 38 — HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (03/20/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
HS62A CUT-OFF SAW —V-BELT COVER (CLUTCH SIDE) ASSY.
V-BELT COVER (CLUTCH SIDE) ASSY.
NO.
25
31
34
40
41
42
43
44
PART NO.
PART NAME
V-BELT COVER, (CLUTCH SIDE)
NUT
WASHER
SCREW
SCREW
GUARD, BELT INNER
WASHER
QTY.
REMARKS
HS52020240
HS50010148R
HS3833073
HS3806021A
HS3801066
HS52020019
HS3916008R
HS006000300
1
2
3
2
1
1
2
1
BUSHING
HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (10/20/06) — PAGE 39
Download from Www.Somanuals.com. All Manuals Search And Download.
HS62A CUT-OFF SAW —V-BELT COVER (PULLEY) /BLADE GUARD ASSY.
V-BELT COVER (PULLEY-SIDE)/BLADE GUARD ASSY.
BLADE FLANGE
INNER (LIP)
10
8
2
1
34
5
14
BLADE FLANGE
OUTER (FLAT)
6
13
22
34
14
20
14
46
23
12
24
28
7
27
4
36
11
12
37
35
15
21
9
6
38
39
16
47
45
17
18
26
32
33
CLUTCH
PULLEY
34
19
29
30
PAGE 40 — HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (03/20/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
HS62A CUT-OFF SAW —V-BELT COVER (PULLEY) /BLADE GUARD ASSY.
V-BELT COVER (PULLEY-SIDE)/BLADE GUARD ASSY.
NO.
1
2
4
5
6
7
8
PART NO.
PART NAME
BLADE COVER 14-INCH
SCREW AND WASHER
SPACER
FLANGE, ARBOR (OUTER)
SPACER
QTY.
1
1
1
1
2
1
3
REMARKS
HS52010026
HS52010177
HS52010045
HS018600235
HS52010044
HS018600019
HS3806022
SHAFT
SCREW
9
HS005000343
HS018600236A
HS018100029
HS3035019
HS093000020
HS094000251
HS52010039
HS01860004A
HS3918013
WASHER
1
1
1
2
1
5
1
1
1
1
17
5
1
1
1
1
1
2
1
2
3
1
1
6
1
1
1
1
1
1
1
2
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
26
27
28
29
30
32
33
34
35
36
37
38
39
45
46
47
FLANGE, ARBOR (INNER)
O-RING, BLADE GUARD SUPPORT
BEARING
SPACER
NUT
SPACER
PULLEY, BELT
WASHER
SCREW
PLATE
SCREW
ARM
FLANGE
LOCK, GUIDE BLADE GUARD
GUIDE, BLADE GUARD
KNOB, ADJUSTMENT GUIDE
SCREW
SUPPORT BLADE GUARD
SCREW
HS3806065
HS52010305
HS3806021
HS52010212
HS52010043
HS52010013
HS52010396
HS52010062
HS3802005A
HS52010025A
HS3801016
HS3914010
NUT
V-BELT
HS52020020
HS52010022A
HS3833073
HS3806037A
HS52010211
HS52010046
HS52010401
HS52010036
HS3833080
COVER, V-BELT (PULLEY SIDE)
WASHER
SCREW
GUARD
BUSHING
SCREW
BELT ADJUSTER
WASHER
SCREW
PLASTIC PIN
HS3906019
HS52010428
HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (10/20/06) — PAGE 41
Download from Www.Somanuals.com. All Manuals Search And Download.
HS62A CUT-OFF SAW — FUELTANK ASSY.
FUEL TANK ASSY.
PAGE 42 — HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (03/20/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
HS62A CUT-OFF SAW — FUELTANK ASSY.
FUEL TANK ASSY.
NO.
4
5
6
8
PART NO.
PART NAME
BREATHER
TUBE
FITTING
VALVE BODY
CLIP
QTY.
REMARKS
HS52010082
HS093000448
HS018500066
HS018500096
HS50010093
HS099900090
HS52022005
HS50010061R
HS50010218
HS50010093
HS50140023
1
1
1
1
1
1
9
15
16
0-RING
*
CAP, FUEL ............................................................. 1 ......... INCLUDES ITEM W/
*
19
28
29
30
SHOCK ABSORBER
FILTER, FUEL
TUBE
1
1
1
1
GROMMET
HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (10/20/06) — PAGE 43
Download from Www.Somanuals.com. All Manuals Search And Download.
HS62A CUT-OFF SAW — LIFTING HANDLE AND ROLLER ASSY.
LIFTING HANDLE AND ROLLER ASSY.
PAGE 44 — HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (03/20/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
HS62A CUT-OFF SAW — LIFTING HANDLE AND ROLLER ASSY.
LIFTING HANDLE AND ROLLER ASSY.
NO.
1
2
3
7
17
18
20
21
22
23
25
26
27
29
30
PART NO.
PART NAME
QTY.
1
4
2
2
1
1
1
2
1
1
2
4
1
4
2
REMARKS
HS52020023
HS018100317
HS3072015
HS3801020
HS52020026
HS3960087
HS52010214
HS3960045
HS018100171A
HS52010098
HS38003035
HS52010066R
HS52020077A
HS3833076
HS3806035
HANDLE
SCREW
WASHER
SCREW
GUARD, FUELTANK
SCREW
MAIN ROLLER SUPPORT UPPER
SPACER, ROLLER SUPPORT LOWER
ROLLER
SUPPORT, ROLLER LOWER
SCREW
SHOCK ABSORBER
FUEL TANK ASSY.
WASHER
SCREW
HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (10/20/06) — PAGE 45
Download from Www.Somanuals.com. All Manuals Search And Download.
HS62A CUT-OFF SAW —THROTTLE LINKAGE ASSY.
THROTTLE ASSY.
PAGE 46 — HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (03/20/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
HS62A CUT-OFF SAW —THROTTLE LINKAGE ASSY.
THROTTLE ASSY
NO.
10
11
12
13
PART NO.
PART NAME
QTY.
REMARKS
HS52010092
HS52010077
HS097000028
HS097000024
HS3960040
THROTTLETRIGGER LEVER............................... 1 ......... INCLUDES ITEM W/ #
THROTTLE LOCK LEVER
SPRING
COVER, HANDLE/TANK
SCREW
1
1
1
3
14
38%
39
40#
CAP, THROTTLE LINKAGE ................................... 1 ......... NOT SOLD SEPARATELY
THROTTLE LINKAGE ............................................ 1 ......... INCLUDES ITEM W/ %
PLATE .................................................................... 1 ......... NOT SOLD SEPARATELY
HS52022048A
HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (10/20/06) — PAGE 47
Download from Www.Somanuals.com. All Manuals Search And Download.
HS62A CUT-OFF SAW — FLYWHEEL COVER ASSY.
FLYWHEEL COVER ASSY.
PAGE 48 — HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (03/20/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
HS62A CUT-OFF SAW — FLYWHEEL COVER ASSY.
FLYWHEEL COVER ASSY.
NO.
3
4
5
6
PART NO.
HS005000361
HS3833080
HS004000142
HS500110019A
PART NAME
WASHER, FLAT
WASHER, LOCK
NUT
QTY.
REMARKS
1
1
1
1
FLANGE, STARTER
HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (10/20/06) — PAGE 49
Download from Www.Somanuals.com. All Manuals Search And Download.
HS62A CUT-OFF SAW — FLYWHEEL ASSY.
FLYWHEEL ASSY.
PAGE 50 — HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (03/20/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
HS62A CUT-OFF SAW — FLYWHEEL ASSY.
FLYWHEEL ASSY.
NO.
PART NO.
HS52020247R
HS52012027
PART NAME
QTY.
REMARKS
1
FLYWHEEL................................................ 1 ......... INCLUDES ITEM W/
*
2
PAWL SET
1
*
HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (10/20/06) — PAGE 51
Download from Www.Somanuals.com. All Manuals Search And Download.
HS62A CUT-OFF SAW — IGNITION COIL ASSY.
IGNITION COIL ASSY.
PAGE 52 — HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (03/20/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
HS62A CUT-OFF SAW — IGNITION COIL ASSY.
IGNITION COIL ASSY.
NO.
PART NO.
PART NAME
SPRING SPARK PLUG
CAP, SPARK PLUG
CABLE WIRE
WASHER
WASHER
SCREW
COIL, IGNITION ASSY.............................. 1 ......... INCLUDES ITEMS W/
CONNECTING LINK
SWITCH, ON-OFF
CABLE WIRE, ON-OFF SWITCH
NUT
PLATE, ON-OFF SWITCH
QTY.
REMARKS
7
*
8
*
9
HS094600169
HS094600097A
HS052010362
HS3916004
1
1
1
2
2
2
10
11
12
13
15
16
17
18
19
HS006000315
HS094000227
HS52020148R
HS52010132
HS094500497
HS097000121A
HS099900397
HS004000438
*
1
1
1
1
1
HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (10/20/06) — PAGE 53
Download from Www.Somanuals.com. All Manuals Search And Download.
HS62A CUT-OFF SAW — AIR FILTER ASSY.
AIR FILTER ASSY.
PAGE 54 — HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (03/20/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
HS62A CUT-OFF SAW — AIR FILTER ASSY.
AIR FILTER ASSY.
NO.
1
2
3
3A
4
5
6
7
8
PART NO.
PART NAME
QTY.
REMARKS
HS52012024B
HS330000010
HS018600125R
HS099900778A
HS018600056AR
HS3802002A
HS3049007
FLANGE, PRE- FILTER, CAP
O- RING, FLANGE PRE- FILTER
FILTER, AIR (STANDARD)
1
2
1
FILTER, AIR (WET CUTTING) .................. 1 ......... OPTIONAL
FILTER, AIR INNER
SCREW, FILTER SUPPORT
O-RING
SUPPORT, FILTER
PRE- FILTER, FOAM
SCREW
GASKET, AIR FILTER LOWER
GASKET, AIR FILTER BASE
COVER, AIR FILTER LOWER
SCREW, AIR CLEANER MTG.
WASHER, AIR CLEANER MTG.
COVER, AIR FILTER, UPPER
GASKET, AIR FILTER COVER
KNOB, AIR FILTER COVER
COVER, AIR FILTER, LONG
SCREW, AIR FILTER COVER
1
3
1
1
1
1
1
1
1
3
3
1
1
1
1
2
HS52010014B
HS52020270R
HS093000468A
HS018600090A
HS52020021
HS52010016
HS072700182
HS3833073
HS52022006
HS52010060
HS52010041
HS52020018
HS093000468A
9
10
11
12
13
14
20
21
22
23
24
HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (10/20/06) — PAGE 55
Download from Www.Somanuals.com. All Manuals Search And Download.
HS62A CUT-OFF SAW — CARBURETOR MOUNTING ASSY.
CARBURETOR MOUNTINGASSY.
PAGE 56 — HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (03/20/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
HS62A CUT-OFF SAW — CARBURETOR MOUNTING ASSY.
CARBURETOR MOUNTING ASSY.
NO.
6
PART NO.
PART NAME
QTY.
2
1
1
1
1
1
1
1
1
1
1
1
1
1
REMARKS
HS3833073
WASHER
11
12
13
14
15
16
17
18
19
20
21
22
23
HS52020060
HS094000215A
HS61052009B
HS097000059A
HS52020008B
HS50010028
HS3960057
HS52020271
HS018100354
HS52020177
HS097000092A
HS52020039
HS50020026
SPRING
TUBE
SCREW
SPRING, MANIFOLD
MANIFOLD, OUTER
FLANGE
SCREW
CARBURETOR ASSEMBLY
FUEL LINE, CARBURETOR
SCREW
SCREW
SUPPORT, CARBURETOR
MANIFOLD, INNER
HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (10/20/06) — PAGE 57
Download from Www.Somanuals.com. All Manuals Search And Download.
HS62A CUT-OFF SAW — CARBURETOR ASSY.
CARBURETOR ASSY.
PAGE 58 — HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (03/20/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
HS62A CUT-OFF SAW — CARBURETOR ASSY.
CARBURETOR ASSY.
NO.
PART NO.
PART NAME
THROTTLE SHAFT
STARTER SHAFT
SPINDLE
COVER, TOP
COVER, BOTTOM
SHUTTER
SHUTTER
CLAMP
CAP
SCREW
SPRING
SPRING
SCREW
ADJUST SCREW
SCREW
SCREW "L" CARBURETOR
SCREW "H" CARBURETOR
SCREW
SCREW
SPRING
QTY.
1
1
1
1
1
1
1
1
2
1
2
1
1
1
1
1
1
4
1
1
1
1
1
1
1
2
2
1
REMARKS
1
HS50010095
HS50010096
HS00300201
HS52020080
HS52020081
HS50010099
HS50010100
HS2318839
*
2
3
*
*
4
5
*
*
6
7
*
*
8
9
*
HS2318634
*
10
HS380000338
HS094600148
HS50010106
HS50010109
HS074000240
HS003300209
HS2318837
*
11
*
12
*
13
*
14
*
15
*
16
*
17
*
HS2318838
18
HS035000162
HS003300202
HS095000146
HS094600143
HS50010122A
HS50010123A
HS2318632
HS50010105
HS015400153
HS380000272
HS003300036
HS2318867
*
19
*
20
*
21
*
BALL
22
KIT, GASKET CARBURETOR
KIT, REPAIR CARBURETOR
SUPPORT
SPRING
WASHER
SEAL RING
FITTING
CLAMP
23
24
*
25
*
26
*
27
*
28
*
29
*
2
30
HS52020271
CARBURETOR ASSY., HDA225 ............... 1 ......... INCLUDES ITEMS W/
*
HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (10/20/06) — PAGE 59
Download from Www.Somanuals.com. All Manuals Search And Download.
HS62A CUT-OFF SAW — CRANKSHAFT / PISTON ASSY.
CRANKSHAFT AND PISTON ASSY.
PAGE 60 — HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (03/20/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
HS62A CUT-OFF SAW — CRANKSHAFT AND PISTON ASSY.
CRANKSHAFT AND PISTON ASSY.
NO.
1
2
3
4
PART NO.
PART NAME
SPARK PLUG
SCREW
QTY.
REMARKS
HS3055118
1
4
4
1
1
1
2
HS005100906A
HS3833076
WASHER
HS50010215
HS50020004
HS50010031
HS007201198
HS50092013
HS50092028
HS50010046B
HS3037014
HS50090001R
HS094500028R
HS094500004
HS007201313
HS50012023AR
HS004900137B
HS097000097
HS52010030
HS52010035
HS52010034
HS52010029R
DECOMPRESSOR
PISTON RINGS
PISTON PIN
5 #
*
6
#
7 #
*
RING, PISTON PIN
*
8
9
PISTON ASSEMBLYW /RINGS ..................... 1 ..........INCLUDES ITEMS W /#
CYLINDER ASSEMBLYW /PISTON .............. 1 ..........INCLUDES ITEMS W /
GASKET, CYLINDER
BEARING, UPPER CRANKSHAFT
CRANKSHAFT
KEY, CRANKSHAFT
SEAL RING
SEAL RING, CRANKSHAFT
CLUTCH ASSEMBLY..................................... 1 ..........INCLUDES ITEMS W /
SPRING, CLUTCH
WASHER
BEARING
*
*
10
13
14
15
17
25
27
1
1
1
1
1
1
+
29+
1
1
1
1
1
32
33$
34
35
SPACER, CLUTCH DRUM
BUSHING, CLUTCH DRUM
CLUTCH DRUM ............................................ 1 ..........INCLUDES ITEMS W /$
36
HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (10/20/06) — PAGE 61
Download from Www.Somanuals.com. All Manuals Search And Download.
HS62A CUT-OFF SAW —WATER KIT ASSY.
WATER KIT ASSY.
PAGE 62 — HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (03/20/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
HS62A CUT-OFF SAW — WATER KIT ASSY.
WATER KIT ASSY.
NO.
PART NO.
HS52012062
HS52010121
PART NAME
QTY.
REMARKS
1
WATER KIT ASSY. .......................................................1.......... INCLUDES ITEMS W /
*
2
*
3
*
4
*
5
*
6
*
7
*
FITTING, QUICK DISCONNECT
1
PLASTICTIEWRAPS ..................................................8.......... NOT SOLD SEPARATELY
HOSE CLAMP .............................................................1.......... NOT SOLD SEPARATELY
SCREW, SOCKET HEAD CAPW/WASHER ...............1.......... NOT SOLD SEPARATELY
HOSE, WATER ............................................................1.......... NOT SOLD SEPARATELY
HS52010207
VALVE, SHUT-OFF
1
Items 3-6 are included with the
Water Kit Assembly and cannot be
purchased separately.
NOTE
HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (10/20/06) — PAGE 63
Download from Www.Somanuals.com. All Manuals Search And Download.
HS62A CUT-OFF SAW —TOOLS
TOOLS
PAGE 64 — HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (03/20/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
HS62A CUT-OFF SAW —TOOLS
TOOLS
NO.
1
2
PART NO.
HS4191240
00325
PART NAME
QTY.
REMARKS
TOOL KIT
1
SMOKELESS 2-STROKE OIL....... 1 .............CAN ONLY BE PURCHASED AS A CASE (QTY 36)
HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (10/20/06) — PAGE 65
Download from Www.Somanuals.com. All Manuals Search And Download.
HS62A CUT-OFF SAW — RECOMMENDED DIAMOND BLADES
Recommended Diamond Blades
for Your Side Winder Saw
Light
Weight
Block
Concrete
(Brick)
Pavers
Blade
Type
Green
Concrete
Concrete
Block
Cured Standard
Concrete Red Brick
Soft
Stone
Medium
Stone
Hard
Stone
Asphalt
GES
GES
GPS
GPS
GPSA
SBLA
GPSA
SBL
SBL
SBLA
PDHS1
PDHS1A
PDHS2
PDHS2A
SW2
PDHS1
PDHS1A
PDHS2A
SW2G
PDHS2
SW2
SW2
SW2G
PDHS3
PDHS3A
SDW
PDHS3
PDHS3A
SDW
SWG
SWG
HSC
HSC
HSG
HSG
PVL
KBL
PVL
KBL
BBL
BBL
GET
GET
GPT
TBL
GPT
TBL
PAGE 66 — HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (03/20/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
Effective: February 22, 2006
TERMS AND CONDITIONS OF SALE — PARTS
PAYMENT TERMS
5. Partsmustbeinnewandresalablecon- Multiquipreservestherighttoquoteandsell
dition,intheoriginalMultiquippackage(if directtoGovernmentagencies,andtoOriginal
any), and with Multiquip part numbers Equipment Manufacturer accounts who use
Terms of payment for parts are net 30 days.
FREIGHTPOLICY
clearlymarked.
our products as integral parts of their own
products.
All parts orders will be shipped collect or
prepaidwiththechargesaddedtotheinvoice.
All shipments are F.O.B. point of origin.
Multiquip’sresponsibilityceaseswhenasigned
manifesthasbeenobtainedfromthecarrier,
andanyclaimforshortageordamagemustbe
settledbetweentheconsigneeandthecarrier.
6. Thefollowingitemsarenotreturnable:
SPECIALEXPEDITINGSERVICE
a. Obsolete parts. (If an item is in the
price book and shows as being re- A$35.00surchargewillbeaddedtotheinvoice
placedbyanotheritem,itisobsolete.) forspecialhandlingincludingbusshipments,
insuredparcelpostorincaseswhereMultiquip
mustpersonallydeliverthepartstothecarrier.
(such as gaskets, seals, “O” rings,
b. Any parts with a limited shelf life
andotherrubberparts)thatwerepur- LIMITATIONSOFSELLER’SLIABILITY
MINIMUMORDER
chasedmorethansixmonthspriorto
thereturndate.
Multiquip shall not be liable hereunder for
damagesinexcessofthepurchasepriceofthe
The minimum charge for orders from Mul-
tiquipis$15.00net.Customerswillbeasked
for instructions regarding handling of orders
notmeetingthisrequirement.
c. Anylineitemwithanextendeddealer item with respect to which damages are
netpriceoflessthan$5.00.
claimed, and in no event shall Multiquip be
liable for loss of profit or good will or for any
otherspecial,consequentialorincidentaldam-
ages.
d. Special order items.
RETURNEDGOODSPOLICY
e. Electricalcomponents.
f. Paint,chemicals,andlubricants.
g. Decalsandpaperproducts.
h. Itemspurchasedinkits.
Returnshipmentswillbeacceptedandcredit
willbeallowed,subjecttothefollowingprovi-
sions:
LIMITATIONOFWARRANTIES
Nowarranties,expressorimplied,aremade
in connection with the sale of parts or trade
accessoriesnorastoanyenginenotmanufac-
tured by Multiquip. Such warranties made in
connectionwiththesaleofnew,completeunits
are made exclusively by a statement of war-
rantypackagedwithsuchunits,andMultiquip
neitherassumesnorauthorizesanypersonto
assume for it any other obligation or liability
whatever in connection with the sale of its
products.Apartfromsuchwrittenstatementof
warranty, there are no warranties, express,
impliedorstatutory,whichextendbeyondthe
descriptionoftheproductsonthefacehereof.
1. AReturnedMaterialAuthorizationmust
be approved by Multiquip prior to ship-
ment.
7. Thesenderwillbenotifiedofanymaterial
receivedthatisnotacceptable.
2. ToobtainaReturnMaterialAuthorization,
alistmustbeprovidedtoMultiquipParts
Salesthatdefinesitemnumbers,quanti-
ties, and descriptions of the items to be
returned.
8. Suchmaterialwillbeheldforfiveworking
days from notification, pending instruc-
tions.Ifareplyisnotreceivedwithinfive
days,thematerialwillbereturnedtothe
senderathisexpense.
a. Thepartsnumbersanddescriptions
must match the current parts price
list.
9. Creditonreturnedpartswillbeissuedat
dealer net price at time of the original
purchase,lessa15%restockingcharge.
b. The list must be typed or computer
generated.
10. In cases where an item is accepted, for
which the original purchase document
can not be determined, the price will be
basedonthelistpricethatwaseffective
twelvemonthspriortotheRMAdate.
c. The list must state the reason(s) for
thereturn.
d. The list must reference the sales
order(s)orinvoice(s)underwhichthe
itemswereoriginallypurchased.
11. Credit issued will be applied to future
purchasesonly.
e. The list must include the name and
phonenumberofthepersonrequest-
ingtheRMA.
PRICINGANDREBATES
Prices are subject to change without prior
notice.Pricechangesareeffectiveonaspe-
cificdateandallordersreceivedonorafterthat
datewillbebilledattherevisedprice.Rebates
3. AcopyoftheReturnMaterialAuthoriza-
tionmustaccompanythereturnshipment.
4. Freight is at the sender’s expense. All forpricedeclinesandaddedchargesforprice
partsmustbereturnedfreightprepaidto increaseswillnotbemadeforstockonhand
Multiquip’sdesignatedreceivingpoint.
atthetimeofanypricechange.
HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (10/20/06) — PAGE 67
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION & PARTS MANUAL
HERE'S HOW TO GET HELP
PLEASE HAVETHE MODEL AND SERIAL
NUMBER ON-HANDWHEN CALLING
UNITED STATES
Multiquip Corporate Office
18910 Wilmington Ave.
Carson, CA 90746
MQ Parts Department
800-427-1244
Tel. (800) 421-1244
Fax (800) 537-3927
Fax:800-672-7877
Fax:310-637-3284
310-537-3700
Contact: [email protected]
Mayco Parts
800-306-2926
310-537-3700
Warranty Department
800-421-1244, Ext. 279 Fax:310-537-1173
310-537-3700, Ext. 279
Fax:800-672-7877
Fax:310-637-3284
Service Department
800-421-1244
Technical Assistance
800-478-1244
Fax:310-537-4259
Fax:310-631-5032
310-537-3700
MEXICO
MQ Cipsa
UNITED KINGDOM
Multiquip (UK) Limited Head Office
Hanover Mill, Fitzroy Street,
Ashton-under-Lyne,
Carr. Fed. Mexico-Puebla KM 126.5
Momoxpan, Cholula, Puebla72760Mexico
Tel: (52) 222-225-9900
Fax: (52) 222-285-0420
Tel: 0161 339 2223
Fax: 0161 339 3226
Lancashire OL7 0TL
CANADA
Multiquip
BRAZIL
Multiquip
4110IndustrielBoul.
Laval, Quebec, Canada H7L 6V3
Tel: (450) 625-2244
Fax: (450) 625-8664
Av. Evandro Lins e Silva, 840 - grupo 505 Tel: 011-55-21-3433-9055
Barra de Tijuca - Rio de Janeiro Fax: 011-55-21-3433-9055
© COPYRIGHT 2006, MULTIQUIP INC.
Multiquip Inc. and the MQ logo are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without written permission. All other trademarks are
the property of their respective owners and used with permission.
This manual MUST accompany the equipment at all times. This manual is considered a permanent part of the equipment and should remain with the unit if resold.
The information and specifications included in this publication were in effect at the time of approval for printing. Illustrations are based on the HS62A Cut-Off Saw.
Illustrations, descriptions, references and technical data contained in this manual are for guidance only and may not be considered as binding. Multiquip Inc. reserves the
right to discontinue or change specifications, design or the information published in this publication at any time without notice and without incurring any obligations.
Your Local Dealer is:
Download from Www.Somanuals.com. All Manuals Search And Download.
|