OperatiOn and parts Manual
MOdel st3020b1/st3020bcul
subMersible puMps
Revision #2 (10/28/10)
To find the latest revision of this
publication, visit our website at:
THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.
Download from Www.Somanuals.com. All Manuals Search And Download.
table Of cOntents
component drawings
Pump Assembly................................................ 32-33
Motor Assembly. ............................................... 34-35
Multiquip st3020b1/bcul
submersible pump
Table Of Contents.................................................... 2
Parts Ordering Procedures...................................... 3
Safety Information ................................................ 4-7
Dimensions.............................................................. 8
Specifications .......................................................... 9
Performance Curve................................................ 10
General Information............................................... 11
Components .......................................................... 12
Direct Power Operation ......................................... 13
Float Switches .................................................. 14-15
Float Switches (CB6 Control Box)......................... 16
Float Switches (CB200 Control Box Old Style) ..... 17
Float Switches (CB200 Control Box New Style).... 18
Operation.......................................................... 19-24
Maintenance..................................................... 24-26
Troubleshooting ..................................................... 27
CB6 Wiring Diagram.............................................. 28
CB200 Wiring Diagram.......................................... 29
Explanation of Code in Remarks Column.............. 30
Suggested Spare Parts ......................................... 31
Terms And Conditions Of Sale — Parts ................ 36
NOTICE
Specifications and part numbers are subject to change
without notice.
page 2 — st3020b1/bCUL sUb. pUmp • operation and parts manUaL — rev. #2 (10/28/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
parts Ordering prOcedures
Ordering parts has never been easier!
choose from three easy options:
Effective:
January 1st, 2006
best deal!
order via internet (dealers only):
Order parts on-line using Multiquip’s SmartEquip website!
If you have an MQ Account, to obtain a Username
and Password, E-mail us at: parts@multiquip.
com.
I View Parts Diagrams
I Order Parts
I Print Specification Information
To obtain an MQ Account, contact your
District Sales Manager for more information.
Use the internet and qualify for a 5% discount
on Standard orders for all orders which include
complete part numbers.*
to log in and save!
Order Parts
Note: Discounts Are Subject To Change
Fax your order in and qualify for a 2% discount
on Standard orders for all orders which include
complete part numbers.*
order via Fax (dealers only):
All customers are welcome to order parts via Fax.
domestic (Us) Customers dial:
1-800-6-PARTS-7 (800-672-7877)
Note: Discounts Are Subject To Change
domestic (Us) dealers Call:
1-800-427-1244
order via phone:
non-dealer Customers:
International Customers should contact
their local Multiquip Representatives for
Parts Ordering information.
Contact your local Multiquip Dealer for
parts or call 800-427-1244 for help in
locating a dealer near you.
when ordering parts, please supply:
Ì
dealer account number
Ì
Specify Preferred Method of Shipment:
Ì
Ì
Ì
Ì
Ì
dealer name and address
ꢀ UPS/Fed Ex
ꢀ DHL
ꢀ Truck
I
I
Priority One
Ground
shipping address (if different than billing address)
return Fax number
applicable model number
I Next Day
Second/Third Day
I
Quantity, part number and description of each part
NOTICE
All orders are treated as Standard Orders and will
ship the same day if received prior to 3PM PST.
We aCCept aLL maJor Credit Cards!
st3020b1/bCUL sUb. pUmp • operation and parts manUaL — rev. #2 (10/28/10) — page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
safety infOrMatiOn
Do not operate or service the equipment before reading
the entire manual. Safety precautions should be followed
at all times when operating this equipment.
Failure to read and understand the safety
messages and operating instructions could
result in injury to yourself and others.
Potential hazards associated with the operation of this
equipment will be referenced with hazard symbols which
may appear throughout this manual in conjunction with
safety messages.
Symbol
Safety Hazard
saFetY messages
Burn hazards
The four safety messages shown below will inform you
about potential hazards that could injure you or others.The
safety messages specifically address the level of exposure
to the operator and are preceded by one of four words:
danger,Warning, CaUtion or notiCe.
Electric shock hazards
Rotating parts hazards
Pressurized fluid hazards
saFetY sYmboLs
danger
Indicates a hazardous situation which, if not avoided,
WiLL result in deatH or serioUs inJUrY.
Warning
Indicates a hazardous situation which, if not avoided,
CoULd result in deatH or serioUs inJUrY.
CaUtion
Indicates a hazardous situation which, if not avoided,
CoULd result in minor or moderate inJUrY.
NOTICE
Addresses practices not related to personal injury.
page 4 — st3020b1/bCUL sUb. pUmp • operation and parts manUaL — rev. #2 (10/28/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
safety infOrMatiOn
generaL saFetY
CaUtion
NOTICE
This equipment should only be operated by trained and
qualified personnel 18 years of age and older.
never operate this equipment without proper protective
clothing, shatterproof glasses, respiratory protection,
hearing protection, steel-toed boots and other protective
devices required by the job or city and state regulations.
Whenever necessary, replace nameplate, operation and
safety decals when they become difficult read.
Manufacturer does not assume responsibility for any
accident due to equipment modifications. Unauthorized
equipment modification will void all warranties.
never use accessories or attachments that are not
recommended by Multiquip for this equipment. Damage
to the equipment and/or injury to user may result.
Avoid wearing jewelry or loose fitting clothes that may
snag on the controls or moving parts as this can cause
serious injury.
aLWaYs know the location of the nearest
fire extinguisher.
never operate this equipment when not
feeling well due to fatigue, illness or when
under medication.
aLWaYs know the location of the nearest
first aid kit.
never operate this equipment under the
influence of drugs or alcohol.
aLWaYsknow the location of the nearest phone or keep
a phone on the job site. Also, know the phone numbers
of the nearest ambulance, doctor and fire department.
This information will be invaluable in the case of an
emergency.
aLWaYs clear the work area of any debris, tools, etc.
that would constitute a hazard while the equipment is
in operation.
No one other than the operator is to be in the working
area when the equipment is in operation.
do not use the equipment for any purpose other than
its intended purposes or applications.
st3020b1/bCUL sUb. pUmp • operation and parts manUaL — rev. #2 (10/28/10) — page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
safety infOrMatiOn
a torch or other source of flame. Application of heat in
this manner may heat the oil in the seal cavity above the
critical point, causing pump damage.
pUmp saFetY
danger
neveroperatetheequipmentinanexplosive
atmosphereornearcombustiblematerials.An
explosion or fire could result causing severe
bodily harm or even death.
do not pump water with a temperature greater than
104°F.
do not pump liquids containing acid or alkali.
aLWaYs check strainer before pumping. Make sure
strainer is not clogged. Remove any large objects, dirt
or debris from the strainer to prevent clogging.
Warning
Accidental starting can cause severe injury
or death. aLWaYs place the ON/OFF
switch in the OFF position.
aLWaYs use a large basket strainer when pumping
water that contains large debris.
do not place hands or fingers inside
pump when pump is running.
aLWaYs flush pump (clean) after use when pumping
water concentrated with heavy debris.It is very important
to always flush the pump before turning it off to prevent
clogging.
never disconnect any emergency or
safety devices. These devices are intended for operator
safety.Disconnection of these devices can cause severe
injury, bodily harm or even death. Disconnection of any
of these devices will void all warranties.
Fix damage to machine and replace any broken parts
immediately.
aLWaYs store equipment properly when it is not being
used.Equipment should be stored in a clean, dry location
out of the reach of children and unauthorized personnel.
Risk of Electric Shock - This pump has not been
investigated for use in swimming pool or marine areas.
CaUtion
never lubricate components or attempt service on a
running machine.
do not restrict the flow of the discharge hose as it may
cause the pump to overheat.
never run pump dry.
Be careful of discharge hose whipping under pressure.
aLWaYs allow the machine a proper amount of time to
cool before servicing.
aLWaYs check pump oil level only when pump is cool.
Expansion due to heat may cause hot oil to spray from
the oil plug when the oil plug is removed. The possibility
of severe scalding may exist.
Keep machine in proper running condition.
eLeCtriCaL saFetY
danger
NOTICE
aLWaYs place the pump in an upright position on a
platform before using.The platform will prevent the pump
from burrowing itself on soft sand or mud.
The electrical voltage required to operate
pump can cause severe injury or even death
through physical contact with live circuits.
aLWaYs disconnect electrical power from
pump before performing maintenance on
pump.
never operate pump on its side.
do not allow the pump to freeze in water.
never leave an open pump chamber unattended.
aLWaYs keep the machine in proper running condition.
do not attempt to thaw out a frozen pump by using
Warning
To reduce the risk of electric shock, connect only to a
circuit protected by a Ground-Fault Circuit-Interrupter
(GFCI).
page 6 — st3020b1/bCUL sUb. pUmp • operation and parts manUaL — rev. #2 (10/28/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
safety infOrMatiOn
Control box safety
NOTICE
danger
aLWaYs make certain that the voltage supplied to the
pump is correct. Always read the pump’s nameplate to
determine what the power requirements are.
aLWaYshave a qualified electrician perform the control
box installation.The possibility exists of electrical shock
or electrocution.
Power Cord/Cable Safety
NOTICE
danger
aLWaYs mount control box in a vertical position
protected from harsh environmental elements.
never let power cords or cables lay in water.
neverstand in water while AC power cord is connected
to a live power source.
LiFting saFetY
CaUtion
never use damaged or worn cables or cords. Inspect
for cuts in the insulation.
When raising or lowering of the pump is required, always
attach an adequate rope or lifting device to the correct
lifting point (handle) on the pump.
never grab or touch a live power
cord or cable with wet hands. The
possibility exists of electrical shock,
electrocution or death.
NOTICE
do not lift machine to unnecessary heights.
Make sure power cables are securely connected to the
motor's output receptacles. Incorrect connections may
cause electrical shock and damage to the motor.
never lift the equipment while the electric motor is
running.
transporting saFetY
Warning
NOTICE
never attempt to use the power cord as a lifting or
lowering device for the pump.
aLWaYs shut down pump before transporting.
NOTICE
aLWaYs tie down equipment during transport by
securing the equipment with rope.
aLWaYs make certain that proper power or extension
cord has been selected for the job. See Cable Selection
Chart in this manual.
environmentaLsaFetY/deCommissioningCE
do not pour waste or oil directly onto
the ground, down a drain or into any water
source.
Grounding Safety
danger
Contact your country's Department of Public
Works or recycling agency in your area and arrange for
proper disposal of any electrical components, waste or
oil associated with this equipment.
aLWaYs make sure pump is grounded.
never use gas piping as an electrical ground.
When the life cycle of this equipment is over it is
recommended that the pump casing and all other metal
parts be sent to a recycling center
aLWaYs make sure that electrical circuits are properly
grounded to a suitable earth ground (ground rod) per
the National Electrical Code (NEC) and local codes
before operating generator. Severe injury or death by
electrocution can result from operating an ungrounded
motor.
Metal recycling involves the collection of metal from
discarded products and its transformation into raw
materials to use in manufacturing a new product.
Recyclers and manufacturers alike promote the process
of recycling metal. Using a metal recycling center
promotes energy cost savings.
st3020b1/bCUL sUb. pUmp • operation and parts manUaL — rev. #2 (10/28/10) — page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
diMensiOns
0.9 in
(23 mm)
Figure 1. ST3020B1/BCUL Pump Dimensions
page 8 — st3020b1/bCUL sUb. pUmp • operation and parts manUaL — rev. #2 (10/28/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
specificatiOns
Table 1. Specifications
ST3020B1/BCUL
Model
Type
Centrifugal Submersible Pump
Impeller
Cast Ductile Iron
3 in. (76 mm)
Suction & Discharge Size
Maximum Pumping Capacity 145 gallons/minute (548 liters/minute)
Max Head
66 ft. (20.1 meters)
2 HP (1.5 kW)
1Ø 230 V
Power
Voltage Phase
Starting Amps
Running Amps
Control Box Required
Temperature Range
52.2 A
10.5 A
See Note 3
32°F ~ 86°F (0°C ~ 30°C)
Thermal Overload Protection YES
Rotation
CCW (See Note 1)
Mechanical Seal Oil Capacity 18 in3 (300 cc) (See Note 2)
Power Cable Length
Dry Net weight
50 ft (approx.15 m)
67 lb (31 kg)
1. motor rotation – Upon start-up, the pump "kicks" in the opposite direction of motor rotation. The correct rotation is
counterclockwise (CCW) as viewed from the impeller end of the pump.
2. mechanical seal oil – Use ISO VG32 oil grade. Fill oil cavity 75% to 85% full (allow air space for expansion).
3. Control box - Control box (Table 2) may be required for certain pumping applications.
Table 2. Control box specifications
UL/CSA
Listed
thermal overload Float switch
Model
voltagetype
Protection
Capability
CB6
230 VAC, 60 Hz Single Phase
230 VAC, 60 Hz Single Phase
YES
YES
NO
YES
CB200
YES
YES
st3020b1/bCUL sUb. pUmp • operation and parts manUaL — rev. #2 (10/28/10) — page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
perfOrMance curve
Figure 2. Pump Performance Curve
page 10 — st3020b1/bCUL sUb. pUmp • operation and parts manUaL — rev. #2 (10/28/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
general infOrMatiOn
The Multiquip Model ST3020B1 and ST3020BCUL
submersible pumps are designed to pump water and
is used for the draining (dewatering) of well casings
construction sites, coffer dams, manholes, transformer
vaults and excavations.
never lift the pump by its electrical power cord. ALWAYS
lift the pump by its carrying handle or attach a rope to the
carrying handle.
A pump fully submerged in liquid will not freeze, unless
the liquid freezes. do not allow a partially submerged
pump to freeze. The expansion of water freezing in the
volute may crack the pump, causing expensive repairs. If
there is any danger of the pump being subjected to freezing
temperatures, Lift the pump from water and allow it to drain
thoroughly.
It's slim design (only 6.7 inches in diameter) allows it to fit
easily inside 8-inch casings and eliminates the need for
larger, more costly casings. The pump is powered by a
2-HP, 230-volt, single-phase motor for easy starting with a
6,000-watt generator.
This rugged submersible pump is loaded with features
such as:
If the pump jams or the pump rotor locks for any reason,
disconnect the pump from the power source immediately.
Allowing the pump motor to cycle on and oFF under an
overload condition can burn out the motor.
tHermaL overLoad proteCtion - automatically
shuts off the motor should it reach an unsafe operating
temperature.
When replacement of nuts and bolts is required, use only
recommended parts as referenced in the parts section of
this manual.This pump uses metric threads. do not use
English measurement threads.
HeavY-dUtY LiFting HandLe - provides and
convenient and safe location to attach a lifting device.
strain-reLieFproteCtor- provides added safety
in the event the operator should try lifting the pump from
the electrical cord.
repLaCeabLe disCHarge port - provides easy
maintenance and lower repair costs.
doUbLe oiL-LUbriCated seaL - provides positive
lubrication if the pump should be left running dry. This
helps prevent damage in the event the pump is run dry
for short periods of time.
dUCtiLe iron impeLLer - for abrasion resistance
and extended life.The high-chrome ductile iron material
minimizes wear.
Corrosion-resistant stainLess-steeL
sHaFt - simplifies maintenance
If the pump was used to pump water containing mud, silt,
use clean water to flush out the pump after each use.
do not allow the pump to run dry for an extended period
of time, as this will damage the pump.During maintenance,
dry running is permissible but only for a few seconds.
st3020b1/bCUL sUb. pUmp • operation and parts manUaL — rev. #2 (10/28/10) — page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
cOMpOnents
5. Mechanical Seal –The hydraulic oil in the pump cavity
is designed to provide cooling for the pump seal. This
allows the pump to run dry for a limited period of time.
6. mechanicalsealoilplug – Remove this plug to check
and add lubrication oil (ISO VG32 grade) to the oil
cavity. This oil protects the mechanical seal. Oil cavity
should be full enough to cover seal spring.
7. Strainer Base – This strainer base is made of electro-
coated steel which is resistant to hardware corrosion.
do not pump large objects or debris with this pump.
This pump is for pumping water only. For dewatering
purposes, always place the strainer base on a platform.
8. volute/impeller – Impellers are constructed of ductile
iron to minimize wear and prolong service life.
9. Electric Motor – These submersible pumps utilize a
60 Hz, single-phase, 230 VAC, 2 HP electric motor.
Consult with a licensed electrician before connecting
motor to a power source and control boxes. Observe
all city and local safety codes.
Figure 3. Submersible Pump Components
Figures 3 shows the location of the basic components, for
the ST3020B1/BCUL submersible pump. Listed below is
a brief explanation of each component.
1. AC Power Cable – This unit is supplied with a 50-ft.
(approximately 15 meters) AC power cable with a
NEMA L6-20P grounding-type plug. Always check
the cable for signs of wear. never use a defective
power cable.
2. CarryingHandle– Always carry the submersible pump
by its handle.nevercarry the pump by its power cord.
Carrying or lifting the pump by the power cord will cause
undue stress on the cord and can ultimately dislodge
the cord from the pump.
3. discharge port – Connect a 3-inch hose to this port.
Remember to adequately support the discharge hose
to avoid stress on the pump.
4. thermal overload protection – This pump is
equipped with a thermal overload protection device
that will shut down the motor in the event of high
operating temperatures. The motor will automatically
restart once the temperature returns to an acceptable
operating temperature.
page 12 — st3020b1/bCUL sUb. pUmp • operation and parts manUaL — rev. #2 (10/28/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
direct pOwer OperatiOn
direct power operation
The ST3020B1/BCUL submersible pumps can be configured to operate by direct power (Figure 4) or connected to a
control box (Figures 9, 10 and 11) utilizing float switches. When the pump is connected directly to a 1Ø, 230 VAC, 60 Hz
power source via the L6-20P plug located at the end of the power cord, the pump will operate soon as power is applied. It
is suggested that a quick disconnect switch be installed as a means of turning the power on and off.
When operating the pump using direct power (no control box) the pump must be monitored at all times. Failure to monitor
the pump during operation could lead to severe pump damage should the pump encounter problems such as a stuck
impeller or not fully immersed in water.
EXTERNAL
1Ø 230VAC, 60 Hz
POWER SOURCE
NEMA
L6-20P PLUG
CIRCUIT
BREAKER
BLACK
RED
L1
L2
LIFTING
ROPE
GREEN
GND. BUS
3-INCH
DISCHARGE
HOSE
POWER
CORD
CARRYING
HANDLE
SUPPORT
PLATFORM
SUBMERSIBLE
PUMP
Figure 4. Direct Power Application.
st3020b1/bCUL sUb. pUmp • operation and parts manUaL — rev. #2 (10/28/10) — page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
flOat switches
mechanical Float switch
design Features
Mechanically activated float switches offer a reliable low
current control for dewatering applications.
Float switch housings are constructed of high-impact,
corrosion resistant polypropylene with mechanically
activated, snap action contacts.
How it Works
Suitable for most liquid environments.
Hermetically sealed.
The mechanical float switch control will turn ON (close)
when the float tips 45° above -horizontal, indicating a high
level, and turns OFF (open) when the float switch drops45°
below horizontal.Reference Figure 6 and Figure 7. Maximum
pumping range is 120 degrees. See Figure 5 below.
Thick-walled non-corrosive PVC plastic enclosure.
Pressure tested to 30 ft. (9 meters).
Standard SJO, 16-gauge, 2 conductor cord (20 ft./6.09 m).
Figure 6. Float Switch (Closed)
Figure 5. Pumping Range (Float Switch)
pumping range
The pumping range of the pump is determined by the float
switch tether cord. Use Table 3 as guide line to determine
your required pumping range. Pumping ranges are based
on non-turbulent conditions. Range may vary due to water
temperature and cord shape. Please note as the tether
length increases, so does the variance of the pumping
range.
Figure 7. Float Switch (Open)
Table 3. pumping range
6 in. 8 in. 10 in.
5.08 cm. 10.16 cm. 15.24 cm. 20.32 cm. 25.4 cm. 30.48 cm. 35.56 cm. 40.46 cm.
6 in. 10 in. 14 in. 18 in. 22 in. 27 in. 31 in. 35 in.
15.24 cm. 25.4 cm. 35.56 cm. 45.72 cm. 55.88 cm. 68.58 cm. 78.74 cm. 88.9 cm.
2 in.
4 in.
12 in.
14 in.
16 in.
Tether Length
pumping range
page 14 — st3020b1/bCUL sUb. pUmp • operation and parts manUaL — rev. #2 (10/28/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
flOat switches
Float switches
For unattended operation of the submersible pump two Model SW1WOPA float switches will be required. These float
switches have bare wires on one end of the cable for direct connection to either the CB6 or CB200 Control Boxes. The
illustration below is an example of using two single float switches in a typical dewatering application.
mountingthe Float switches
NOTICE
1. Determine the required cord tether length as shown
in Figure 5 and Table 3.
Single float switch, Model SW1A has a pumping range
between 5.5~18 in. (14~46 cm.). Dual float switch has
a pumping range between 1~ 48 in (2.54~122 cm.)
2. Place the cord into the clamp as shown in Figure 8.
3. Secure the clamp to the discharge hose as shown in
Figure 8. do not install cord under hose clamp.
4. Using a screwdriver, tighten the hose clamp. do not
over- tighten. Make sure the float cord is not allowed
to touch the excess hose clamp band during operation.
EXTERNAL
1Ø 230VAC, 60 Hz
POWER SOURCE
CIRCUIT
BREAKER
CONTROL
BOX
BLACK
RED
L1
L2
PUMP
POWER
PLUG
GREEN
GND. BUS
DISCHARGE
HOSE
PUMP
ON
SINGLE
FLOAT SWITCH
APPLICATION
PUMPING
RANGE
MODEL SW1WOPA
3.5 in. (9 cm.)
MINIMUM
TETHER
PUMP
OFF
LENGTH
SUBMERSIBLE
PUMP
Figure 8. Single Float Switch (2) Application Diagram
st3020b1/bCUL sUb. pUmp • operation and parts manUaL — rev. #2 (10/28/10) — page 15
Download from Www.Somanuals.com. All Manuals Search And Download.
flOatswitches(cOntrOlbOx)
Control boxes (Cb6 and Cb200)
For special remote pumping applications of the submersible pump, a control box (Models CB6 or CB200) is required.These
water resistant control boxes provides watertight housing and glands to prevent water from leaking into the box, and a float
switch interface. Both control boxes will require the use of two SW-1WOPA float switches, no plug, bare wires for direct
connection to the control box. See Figures 9, 10 and 11 for control box connections.
A1
1L1 3L2 5L3 13NO
24
12
CONTACTOR
ABB
A16-30-10
MANUAL/AUTO
SWITCH
SW-1
23
11
2T1 4T2 6T3 14NO
A2
WARNING
R
S
U
V
V
Y
Y
1
2
3
4
B
A
CONTROL BOX INSTALLATION IS TO BE
PERFORMED BY A LICENSED ELECTRICIAN
OR QUALIFIED PERSONNEL.
TB1
THE POSSIBILITY OF ELECTRICAL SHOCK
OR ELECTROCUTION EXISTS, WHICH COULD
CAUSE SEVERE BODILY HARM EVEN DEATH!.
R
S
U
V
V
Y
Y
1
2
3
4
GROUND
EXTERNAL SINGLE-PHASE
(230 VOLT)
POWER SOURCE
FLOAT
SWITCH
INPUTS
SINGLE-PHASE
230 VAC INPUT
POWER CABLE
CIRCUIT
BREAKER
L1
L2
BLACK
WHITE
SINGLE-PHASE
230 VAC OUTPUT
POWER CABLE
TO PUMP
START FLOAT
SWITCH. CONNECT
TO TERMINALS 1 AND 2
SECURE FLOAT SWITCH
WIRES TO PUMP
DISCHARGE HOSE
GROUND
TB1 REFERENCE CHART
TERMINAL
NO.
DESTINATION
WIRE COLOR SIZE
LIFTING
ROPE
SINGLE
TB1-A1
TB1-A2
TB1-A3
TB1-A4
TB1-AR
TB1-AS
TB1-GND
TB1-AU
TB1-BU
TB1-AV
TB1-BV
TB1-BR
TB1-BR
TB1-BS
TB1-BS
TB1-B1
TB1-B1
TB1-B2
TB1-B4
TB1-B4
STOP FLOAT SW
STOP FLOAT SW
BLACK 14 AWG
WHITE 14 AWG
FLOAT SWITCH
APPLICATION
START FLOAT SW BLACK 14 AWG
START FLOAT SW WHITE 14 AWG
230 VAC LINE
230 VAC LINE
GROUND
RED 14 AWG
MODEL SW1WOPA
BLACK 14 AWG
GREEN 14 AWG
RED 14 AWG
PUMPING
RANGE
PUMP MOTOR
CONTACTOR 2T1
PUMP MOTOR
CONTACTOR 4T2
CONTACTOR 1L1
SW1-11
BLACK 14 AWG
BLACK 14 AWG
RED 14 AWG
SUBMERSIBLE
PUMP
BLACK 14 AWG
BLACK 14 AWG
BLACK 14 AWG
BLACK 14 AWG
BLACK 14 AWG
BLACK 14 AWG
BLACK 14 AWG
BLACK 14 AWG
BLACK 14 AWG
STOP FLOAT
SWITCH. CONNECT
TO TERMINALS 3 AND 4
CONTACTOR 3L2
COIL A2
SW1-24
TB1-B3
CONTACTOR 5L3
CONTACTOR 6T3
COIL A1
Figure 9. CB6 Control Box Dual Float Switch Application Diagram
page 16 — st3020b1/bCUL sUb. pUmp • operation and parts manUaL — rev. #2 (10/28/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
flOatswitches(cOntrOlbOx)
NOTE:
CHECK JUMPER SETTINGS ON
TRANSFORMER, REFERENCE
CB200 WIRING DIAGRAM. 230 VAC
CONFIGURATION SHOWN.
EXTERNAL 1Ø
(230 VAC)
POWER SOURCE
MOUNT CONTROL
BOX IN AN UPRIGHT
VERTICAL POSITION
AS SHOWN.
CIRCUIT
BREAKER
L1
L2
RED
H 1
H 3
H 2
H 4
BLACK
110
115
120
X1
X2
XF
X1
CONTACTOR
FUSE
GROUND
MTE
NOTE:
REFER TO OPERATION MANUAL
AC POWER
TERMINAL BLOCK
FLOAT SWITCH
TERMINAL BLOCK
FOR THE CORRECT SETTING OF
THE ELECTRONIC OVERLOAD UNIT.
B
L3
L1 L2
1
2 3 4
FLC (A)
10
STOP
RESET
CLASS
AUTO HAND
10
10
8
12
7
2
0
2
0
16
30
30
6.4
TB1
POWER INPUT CABLE
TO CONTROL BOX
B
1
2 3 4
L3
L1 L2
2
4
6
ELECTRONIC OVERLOAD
MODULE TERMINAL BLOCK
RED
A
RED
BLACK
BLACK
JUMPER
WIRE
GREEN
POWER INPUT
TO CTRL BX.
TERMINAL BD.
FLOAT
SWITCH
INPUTS
1Ø 230 VAC
POWER OUTPUT
TO PUMP
START FLOAT
SWITCH. CONNECT
TO TERMINALS 1 AND 2
SECURE FLOAT SWITCH
WIRES TO PUMP
DISCHARGE HOSE
SINGLE
FLOAT SWITCH
APPLICATION
MODEL SW1WOPA
WARNING
PUMPING
RANGE
CONTROL BOX INSTALLATION IS TO BE
PERFORMED BY A LICENSED ELECTRICIAN
OR QUALIFIED PERSONNEL.
THE POSSIBILITY OF ELECTRICAL SHOCK
OR ELECTROCUTION EXISTS, WHICH COULD
CAUSE SEVERE BODILY HARM EVEN DEATH!.
STOP FLOAT
SWITCH. CONNECT
TO TERMINALS 3 AND 4
SUBMERSIBLE
PUMP
NOTICE
For correct wiring to pump motor (1Ø, 230 VAC), add
a 16 AWG. jumper wire approximately 5-inches in
length between the input terminal block marked L3 and
terminal 4 on the electronic overload unit. Reference
CB200 wiring diagram (old style)
Figure 10. CB200 Control Box (Old Style)
Dual Float Switch Application Diagram
st3020b1/bCUL sUb. pUmp • operation and parts manUaL — rev. #2 (10/28/10) — page 17
Download from Www.Somanuals.com. All Manuals Search And Download.
flOatswitches(cOntrOlbOx)
NOTE:
CHECK JUMPER SETTINGS ON
TRANSFORMER, REFERENCE
CB200 WIRING DIAGRAM. 230 VAC
CONFIGURATION SHOWN.
EXTERNAL
1Ø 230VAC, 60 Hz
3Ø 230/460 VAC, 60 Hz
POWER SOURCE
A1
3L2
A2
1L1
5L3
13NO
MOUNT CONTROL
BOX IN AN UPRIGHT
VERTICAL POSITION
AS SHOWN.
CIRCUIT
BREAKER
RED
L1
L2
ABB
A16-30-10
H 1
H 3
H 2
H 4
BLACK
110
115
120
CONTACTOR
X1
X2
XF
X1
2T1
4T2
6T3
14NO
FUSE
NOTE:
REFER TO OPERATION MANUAL
FOR THE CORRECT SETTING OF
THE ELECTRONIC OVERLOAD UNIT.
GROUND
1L1 3L2 5L3
AC POWER
TERMINAL
BLOCK
WHITE
B
E
16 DU
TRIP CLASS 10
ABB
8
RESET
10
ON
L3
L1 L2
12
ELECTRONIC OVERLOAD
UNIT TERMINAL BLOCK
1
2
3
4
MAN
AUTO
18A
STOP
TEST
TB1
95 NC 96
97 NO 98
POWER INPUT CABLE
TO CONTROL BOX
2
T1
4
T2
6
T3
1
2
3
4
L3
L1 L2
A
RED
FLOAT SWITCH
TERMINAL BLOCK
BLACK
RED
BLACK
JUMPER
WIRE
GREEN
FLOAT
SWITCH
INPUTS
POWER INPUT
TO CTRL BX.
TERMINAL BD.
1Ø 230 VAC
POWER OUTPUT
TO PUMP
START FLOAT
SWITCH. CONNECT
TO TERMINALS 1 AND 2
SECURE FLOAT SWITCH
WIRES TO PUMP
DISCHARGE HOSE
SINGLE
FLOAT SWITCH
APPLICATION
MODEL SW1WOPA
WARNING
PUMPING
RANGE
CONTROL BOX INSTALLATION IS TO BE
PERFORMED BY A LICENSED ELECTRICIAN
OR QUALIFIED PERSONNEL.
THE POSSIBILITY OF ELECTRICAL SHOCK
OR ELECTROCUTION EXISTS, WHICH COULD
CAUSE SEVERE BODILY HARM EVEN DEATH!.
STOP FLOAT
SWITCH. CONNECT
TO TERMINALS 3 AND 4
SUBMERSIBLE
PUMP
NOTICE
For correct wiring to pump motor (1Ø, 230 VAC), add
a 16 AWG. jumper wire approximately 5-inches in
length between the input terminal block marked L3 and
terminal 4 on the electronic overload unit. Reference
CB200 wiring diagram (new style)
Figure 11. CB200 Control Box (New Style)
Dual Float Switch Application Diagram
page 18 — st3020b1/bCUL sUb. pUmp • operation and parts manUaL — rev. #2 (10/28/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
OperatiOn
Hose Connections
1. Connect a 3-inch hose to the discharge port on the
pump as shown in Figure 8. Make sure that hose is
attached correctly to the discharge port.
attaching Lifting rope
1. Attach a suitable lifting cable (rope) to the carrying
handle (Figure 12) on the pump and lower the pump
into place.For applications where there is an excessive
amount of mud, grit or silt, the use of a support platform
is desirable.When pumping water from swimming pool
type applications where there is little or no debris, the
support platform is not required.
EXTERNAL
1Ø 230VAC, 60 Hz
POWER SOURCE
NEMA
L6-20P PLUG
CIRCUIT
BREAKER
BLACK
RED
L1
L2
LIFTING
ROPE
GREEN
GND. BUS
Figure 13. Submersible Pump
Tilted Position (Incorrect)
3-INCH
DISCHARGE
HOSE
POWER
CORD
pump power Connections (no Control box)
1. Make sure circuit breaker supplying power to pump
motor is in the oFF position.
CARRYING
HANDLE
2. Insert the L6-20P power cable plug (Figure 12) into
the appropriate power source receptacle. The correct
source voltage for this pump is 230VAC, 60 Hz, single-
phase.
SUPPORT
PLATFORM
SUBMERSIBLE
PUMP
3. If all of the pump's electrical requirements have been
met, place the circuit breaker or power ON/OFF switch
in the on position.
4. Wait a few seconds and water should begin to flow
from the discharge hose.
5. If water is not flowing from the discharge hose or not
flowing freely after a few minutes, place the circuit
breaker or ON/OFF switch in the oFF position and
check the system for leaks.
Figure 12. Submersible Pump
Upright Position (Correct)
2. Make sure the pump is always placed in an upright
position (Figure 12), and not tilted (Figure 13). Never
position the pump directly on a soft, loose bottom.
Remember to attain maximum pumping capacity and
prevent excessive wear.Position the pump so it will not
burrow itself into sand or clay.
NOTICE
When connecting the pump directly to a power source
(no control box), it is recommended that personnel
monitor the pump while in operation. Severe pump
damage can occur if left unattended.
For unattended operation Multiquip recommends the
use of either the CB6 or CB200 control box.
st3020b1/bCUL sUb. pUmp • operation and parts manUaL — rev. #2 (10/28/10) — page 19
Download from Www.Somanuals.com. All Manuals Search And Download.
OperatiOn
Control box installation
single-phase power installation (input)
The following procedure outlines the steps for connecting
the pump to a control box.
The ST3020B1/BCUL submersible pump requires 1Ø, 230
VAC, 60 Hz, power for normal operation.
If you cannot determine what your pump's power
requirements are, look at the vendor supplied identification
name tag attached to the pump or contact Multiquip's
service department.
danger
The ST3020B1 and SB3020BCUL
submersible pumps are also designed
to work with a control box. This control
NOTICE
box contains the necessary electronics
(float switch connections) to operate the
Applying incorrect power (voltage or voltage phase)
to the submersible pump can cause severe damage
to the pump motor. Please make sure that the correct
voltage and phase are connected to the pump motor
at all times.
pump. Remember this control box contains hazardous
voltages. Disconnect all sources of power before
installing or servicing. There exists the possibility of
electrocution, electric shock or burn, which can cause
severe bodily harm or even death!
power Cord requirements
danger
When routing the 230 VAC, 60 Hz., single phase power via
a power cord to the control box, aLWaYs use the correct
wire size. Please refer to Table 4 to determine the correct
wire size. Incorrect wire size can adversely affect the
performance of the pump and may ultimately burn-out the
pump motor.
When installing the control box, the
possibility exists of electrical shock,
electrocution and possibly death! never
have untrained personnel perform the
installation. aLWaYs have qualified
service personnel (licensed electrician) perform the
installation.
Table 4. Power Cord Length
and Wire Size
Warning
50 Ft.
(15.24 m)
100 Ft.
(30.48 m)
150 Ft.
(45.72 m)
AMPS
Explosion or Fire Hazard exists if this pump
is used with flammable liquids.donotuse
this pump with flammable liquids.donot
install this pump in hazardous locations as
defined by the National Electrical Code,
ANSI/NFPA 70.
6
16 AWG
16 AWG
16 AWG
14 AWG
14 AWG
12 AWG
16 AWG
14 AWG
14 AWG
14 AWG
12 AWG
12 AWG
14 AWG
12 AWG
12 AWG
12 AWG
10 AWG
10 AWG
8
10
12
14
16
Control box mounting
Mount the control box in an upright vertical position.
Make sure the control box is securely fastened to a flat
surface, that is free of dust, dirt, moisture or any elements
that may contaminate or erode the electronic components
of the control box.
page 20 — st3020b1/bCUL sUb. pUmp • operation and parts manUaL — rev. #2 (10/28/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
OperatiOn
4. Connect the other end of the AC power cord to the
voltage source. Remember to provide a means of
disconnecting the power from the control box (circuit
breaker or quick disconnect switch). Also make sure
to provide a good earth ground to the control box
Connecting dual float switch (sW-1Wop) to
Control box
1. Remove the float switch input connector housing, then
route the float switch wires through the cable gland on
the control box. Attach the wires of the float switch to
the terminal block as indicated by Table 5 and Figures
7, 8 and 9.
NOTICE
It is recommended that the power being supplied to the
control box aLWaYsbe connected to a circuit breaker
or a quick disconnect switch. This safety feature
allows for quick removal of power from the control box
in the event of an emergency.
Table 5. dual Float switch Connections
Float
Switch
Terminal
block no.
Wire
Color
Control
box
TB1-A1
TB1-A2
Black
White
Start
Stop
CB6/CB200
CB6/CB200
Connecting AC Power to the Pump Motor
TB1-A3
TB1-A4
Black
White
1. AC power is routed to the pump motor via a contactor/
thermal overload unit. The coil of the contactor is
energized or de-energized by the opening and closing
of the float switch contacts. The thermal overload unit
protects the windings of the electric motor in the event
of a stuck impeller.
2. Tighten the connector housing to ensure a tight fit
between the cord and the connector body. This will
prevent the cable from pulling out of the terminal block
and also prevent moisture from entering the control box.
2. The power cord should have three wires. Each wire is
color coded.The colors are red, BLACK and green.
3. Determine the tether length of the float switch wires
then secure float switch wires to pump discharge hose.
See Figure 8 and Table 3 to determine the pumping
range.
3. Remove the pump AC input connector housing from
the control box, then route the power cord through the
cable gland on the control box.
Connecting aC power to the Cb 200 Control box
4. Connect pump power cord to the thermal overload unit
and TB1 as shown in Figures 8, 9 and Table 7.
1. The AC power cord (input) should have three wires.
Each wire is color coded.The colors are red, BLACK
and green.
table 7. 1Ø-230vaC power
Connections
2. Remove the AC input connector housing from the
control box, then route the power cord through the
cable gland on the control box.
Wire
Color
Cb200thermal overload Unit
Terminal Block TB1
BLACK
RED
T1-2 (L1)
T3-6 (L3)
TB1-GND
3. Connect the AC power cord to the terminal block (TB1)
located inside the control box as shown in Figures 9,
10, 11 and Table 6.
GREEN
Table 6. 1Ø-230vaC power
Connections
5. Install jumper wire between T2 of electronic overload
module and TB1-L3. Reference Figures 10 and 11.
Wire
Color
CB6 Terminal
block no.
CB200 Terminal
block no.
NOTICE
CB6 control box does not have thermal overload
capability. Install jumper wire (CB200 Control Box)
betweenT2 of electronic overload module andTB1-L3.
Jumper wire must be installed in order for electronic
overload module to work correctly.
BLACK
RED
TB1-AR (L1)
TB1-AS (L2)
TB1-GND
TB1A-L1
TB1A-L2
TB1-GND
GREEN
st3020b1/bCUL sUb. pUmp • operation and parts manUaL — rev. #2 (10/28/10) — page 21
Download from Www.Somanuals.com. All Manuals Search And Download.
OperatiOn
electronic overload module settings
reset operation
NOTICE
This electronic control unit has two modes of reset. The
modes are defined as follows:
aLWaYs make sure that the electronic overload
module supplied with the control box is set to the correct
amperage. This overload module must matCH the
amperage requirements of the pump motor.
MODE 1
When the CLASS dial on the electronic overload module
is in the Hand position (manual) the reset button (Figure 15)
on the front of the control box must be pushed to reset the
unit (restore power) in the event of an overload.
Using an electronic overload unit with incorrect settings
may result in serious damage to the pump. aLWaYs
check the nameplate on the pump to determine the
required amperage settings for the overload module.
Cb200 Control box old style electronic overload
Module
Figure 15. Control Box Reset Button
There are two dials on the Electronic Overload Module
(Figure 14) that require setting before the pump can be
used with the control box.
MODE 2
When the CLASS dial on the electronic overload module
is in the aUto position (automatic mode) the unit will
automatically be reset in the event of an overload
These dials are located on top of the overload module and
are labeled CLASS and FLC (A).
Use a phillips-head screw driver to adjust the dials to the
correct settings.
NOTICE
The CB200 Control Box (old style) is shipped from the
factory with the CLASS dial set to the Hand position.
Full Load Current (FLC) Amps Dial Setting
1. Set the FLC (A) dial pointer (Figure 14) to 10.5. This
setting represents the running amps of the pump.This
information can be located on the pump's nameplate.
Cb200 Control box new style electronic overload
Module
There are two dials (A and B) on the Electronic Overload
Module (Figure 16) that require setting before the pump
can be used with the control box.
Figure 14. Electronic Overload
Module (Old Style)
Class Dial Setting
1. Depending on the application, Set the CLASS dial
pointer (Figure 14) to either Hand (manual) or aUto.
2. There are 3 groups of numbers on the CLASS dial that
range from 10 to 30.These numbers represent the trip
class of the thermal overload device.
3. Set the CLASS dial pointer to position 10.This setting
controls the reset function only. It does not affect the
ability of the pump to run with or without float switches.
Figure 16. Electronic Overload
Module (New Style)
page 22 — st3020b1/bCUL sUb. pUmp • operation and parts manUaL — rev. #2 (10/28/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
OperatiOn
Full Load Current (FLC) Amps Dial A Setting
automatic operation
1. Set dial A pointer (Figure 16) to 10.5. This setting
represents the running amps of the pump. This
information can be located on the pump's nameplate
1. From the voltage source set the circuit breaker or quick
disconnect switch to the on position.
2. Make sure float switches have been connected to the
control box. References Figures 9,10 and 11.
Reset Dial Setting
3. For automatic operation of the pump, place the
3-position operation switch (Figure 19) on the control
box in the aUto position.
1. Depending on the application, Set reset dial B
pointer (Figure 16) to either aUto or man.
manual operation
1. From the voltage source set the circuit breaker or quick
disconnect switch to the on position.
2. For manual operation of the pump, place the 3-position
operation switch (Figure 17) on the control box in the
manUaL position.
Figure 19. Manual-Off-On SW. (AUTO Position)
4. In the aUto mode the pump will run as long as there
is a sufficient amount of water for the start float switch
to be activated. This water level is determined by the
setting of the float switches.
The stop float switch contacts will open when the
water level is low and power will be removed from the
pump's motor.
Figure 17. Manual-Off-On SW. (Man Position)
3. Verify that the on indicator (Figure 18) on the control
box is LIT. This means that power is being supplied to
the control box.
5. Once the water level has risen back to the appropriate
level the start float switch contacts will close and power
will be restored to the pump's motor.
Figure 18. Control Box Power ON Indicator
4. In the manual mode the pump will run continuously.Pay
close attention when running the pump in this mode.
Severe damage to the pump may occur if pump is
not immersed in water.
st3020b1/bCUL sUb. pUmp • operation and parts manUaL — rev. #2 (10/28/10) — page 23
Download from Www.Somanuals.com. All Manuals Search And Download.
OperatiOn/Maintenance
shut-down
Lubrication
1. Place the 3-position operation switch on the control
box in the oFF position (Figure 20).
To check the lubrication oil level of the mechanical seal
perform the following:
Checking Lubrication Oil Level
1. Lay the pump (Figure 21) on its side with the oil plug
facing upwards.
2. Using an allen wrench, remove oil fill plug.
Figure 20. Manual-Off-On SW. (OFF Position)
3. Visually inspect oil plug hole to verify that oil cavity is
full enough to cover seal spring.
2. Verify that the control box power ON light is oFF.
3. Remove the power from the pump by turning off the
circuit breaker or switch that provides power to the
pump.Remember to make sure that hands are dry (not
wet), and feet are not standing in water when removing
or disconnecting power from the pump.
4. When reinstalling oil fill plug, apply teflon tape to
prevent leaking.
Changing Lubrication Oil
1. If lubrication oil level is low, block the oil fill opening
with a finger and roll pump to one side to drain oil into
a small container.
4. Using the lifting rope, lift the pump up from its current
position. Remove the discharge hose from the
discharge port on the pump.
2. Use a funnel (Figure 21) and fill oil cavity with ISO
VG32 lubrication oil or equivalent. Pump oil cavity
capacity is 300 cc. Fill to 75-80% capacity to allow for
expansion. Replace lubrication oil every 6 months
(1,000 hours) or as needed.
5. Remove all power cables and float switches from
the control box. Place cables and float switches in a
suitable container where they will not get damaged.
Cleanup
1. Wipe off any mud or debris that might have attached
itself to the pump.
2. If the pump was used to pump mud, grit or silt, flush
vigorously with clean water.
3. Store pump in a clean dry place away from dirt and
debris.
Figure 21. Adding Lubrication Oil
page 24 — st3020b1/bCUL sUb. pUmp • operation and parts manUaL — rev. #2 (10/28/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Inspecting Lubrication Oil (Mechanical Seal)
1. Block the oil fill opening with a finger and roll pump to
one side to drain (Figure 22) oil into a small transparent
container.
2. If oil is cloudy (milky) or has water in it, indicates
that mechanical seal is defective or worn. Replace
mechanical seal.
Figure 22. Lubrication Oil Inspection
impeller/mechanical seal replacement
Refer to the the following procedure and Figure 23 for the
removal of the impeller and mechanical seal.
1. Remove the three strainer bolts (item 147) that secure,
strainer to the suction cover (item 176). Remove
strainer (item 146).
2. Remove the four suction cover bolts (item 177) that
secure the suction cover (item 176) to the casing (item 1).
Remove suction cover.
3. Remove suction cover packing (item 179) from suction
cover and friction disc (items 176 and 2).
2
4. Remove impeller nut (item 4) and washer (item 53).
5. Remove impeller (item 3) and impeller key (item 6)
from motor shaft. Remove mechanical seal (item 60).
6. Remove adjustment liner (item 47).
7. Reassemble in reverse order.
Figure 23. Impeller/Mechanical Seal Removal
st3020b1/bCUL sUb. pUmp • operation and parts manUaL — rev. #2 (10/28/10) — page 25
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
electrical insulationtesting
NOTICE
Why perform electrical insulation testing?
Insulation resistance is moisture and temperature
sensitive. When temperature increases, insulation
resistance decreases, and vice versa.
Electrical insulation starts to age as soon as it's made.
Harsh environments, especially those with extreme
temperature changes and/or chemical contamination,
cause further deterioration of the insulation (power cord).
When performing this test measurement, perform the
test using the same test parameters as used in the
initial testing.
As a result, personnel safety (electrocution/shock) and
power reliability can suffer resulting in higher operating
cost and maintenance.
What is Insulation ResistanceTesting
20M W
POWER CABLE
INSULATION
Insulation resistance testing applies a regulated stabilized
high voltage (Figure 24), typically 500 VDC or greater
across a dielectric (power cord). Measuring the amount of
leakage current flowing through the dielectric will yield a
resistive measurement in megohms.
MW
V
OFF
W
KW SET
UP
GROUND
PIN
W
MEGGER™
500 VDC INSULATION
TEST METER
Insulating MaterialTesting
SUBMERSIBLE
PUMP
To verify the integrity of the pump's insulating material
(power cable) it will be necessary to perform an electrical
insulation test. Any electrical insulation must have the
opposite characteristic as the conductor: it should resist
the flow of current, keeping it within the conductor.
To measure the IR (current x resistance), the use of an IR
tester must be employed.This IR tester is a portable device
that is a resistance meter (ohmmeter) with a built in DC
generator that develops a high DC voltage.
Figure 24. Insulation Tester Application
danger
The high DC voltage from the IR tester is usually 500 VDC
or more.This voltage, when applied causes a small current
to flow through and over the insulation's surfaces.The tester
provides a direct reading of IR in megohms.
Read and follow the manufacturer's users
manual prior to operating insulation tester
(megaohm meter). This meter generates
a test voltage of 500 volts or greater. Only
qualified and trained personnel should
use this equipment. The possibility exists of severe
electrical shock, electrocution even death!, when
using insulation tester.
A high resistance reading would indicate a "good"
insulation, meaning very little current is escaping through
the insulation. While a relatively low resistance reading
would indicate a poor insulation, meaning a significant
amount of current may be leaking through and along the
insulation.
page 26 — st3020b1/bCUL sUb. pUmp • operation and parts manUaL — rev. #2 (10/28/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
trOubleshOOting
table 8. Pump Troubleshooting
sYmptom
possibLe probLem
soLUtion
Check that proper voltage (230 VAC, 60 Hz, single-
phase) is being supplied to the pump. Also check that
there is an adequate amount of current (amps) to run
the pump. Check power source circuit breaker.
Incorrect voltage/amps?
Check electrical connec-
tions?
If using float switches check wiring, inspect power
cord.
Blown power fuse or tripped Replace fuse check circuit breaker, check cause of
circuit breaker?
blown fuse or tripped breaker.
Pump Fails To Start
Disconnect power cord and check for clogging. Un-
clog pump. Check overload protection device.
Impeller locked?
Use multimeter to check motor insulation. Insulation
resistance must be approximately 15 megaohms. If
resistance is low, disassemble pump motor and bake
windings to dry them.
Wet motor windings?
Defective motor and pump
bearings?
Check for excessive bearing wear, if worn replace
bearings. Replace motor if defective.
Twisted or restricted dis-
charge hose?
Lay hose flat un-kinked. Remove clog from hose line.
Clean strainer.
Clogged pump strainer?
Use a voltmeter to check voltage while pump is
energized. Voltage must be within 10%. Check
power source (no load and load). If an extension cord
is used, make sure it has adequate current-carrying
capacity for the required length. See Table 4.
Pump Fails to Deliver Full
Output
Low voltage?
Impeller worn?
Replace impeller.
Defective mechanical seal?
Loose Oil Fill Plug?
Replace mechanical seal.
Tighten securely. Apply teflon tape.
Water in Mechanical
Seal Oil
st3020b1/bCUL sUb. pUmp • operation and parts manUaL — rev. #2 (10/28/10) — page 27
Download from Www.Somanuals.com. All Manuals Search And Download.
cb6 wiring diagraM
PUMP
POWER
CORD
230 VAC, 60 Hz.
ELECTRIC MOTOR
WIRING DIAGRAM
EXTERNAL 1-PHASE
(230 VAC, 60 Hz.)
POWER SOURCE
THERMAL
PROTECTOR
INPUT
POWER
CORD
CIRCUIT
BREAKER
BLK
RED
RED
L1
L2
BLACK
BLACK
GREEN
MAIN
COIL
GND
GREEN
GROUND
MAIN
COIL
AUX
COIL
R
S
U
V
V
Y
Y
B
C1
RED
TB1
90µF@400 VDC
ALL WIRES ARE BLACK 14 AWG.
UNLESS OTHERWISE NOTED.
A
R
S
U
V
V
Y
Y
GREEN
2-POLE
OPERATION
SWITCH
0N
(MANUAL)
12 (R)
11 (R)
CONTACTOR
COIL
R
AUTO
4
S
23 (G)
24 (G)
A2
A1
4
JUMPER
WIRE
1
2
3
4
B
U
V
R
S
1L1
3L2
2T1
4T2
TB1
1
2
3
4
A
WHITE
BLACK
2
4
WHITE
BLACK
6T3
5L3
GRAY
BLACK
STOP
FLOAT
SWITCH
(LOW)
START
FLOAT
SWITCH
(HIGH)
WARNING
CONTROL BOX INSTALLATION IS TO BE
PERFORMED BY A LICENSED ELECTRICIAN
OR QUALIFIED PERSONNEL.
THE POSSIBILITY OF ELECTRICAL SHOCK
OR ELECTROCUTION EXISTS, WHICH COULD
CAUSE SEVERE BODILY HARM EVEN DEATH!.
Figure 25. CB6 Wiring Diagram
page 28 — st3020b1/bCUL sUb. pUmp • operation and parts manUaL — rev. #2 (10/28/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
cb200 wiring diagraM
EXTERNAL SINGLE-PHASE
(230 VOLT)
POWER SOURCE
SINGLE PHASE WIRING
ELECTRONIC
OVERLOAD UNIT
TERMINALS
CONNECTIONS
CIRCUIT
BREAKER
M
O/L
RED
BLK
L1
L2
1
3
2
4
L1
L2
T1
PUMP
MOTOR
T2
T3
5
6
L3
H1
H3
H2
H4
CONTROL
TRANSFORMER
SEE DETAIL “A” FOR JUMPER SELECTION
230 VAC SELECTION.
GROUND
50VA CPT
6
F1
ADD SUPPLIED JUMPER
WIRE AS SHOWN FOR
SINGLE PHASE OPERATION.
XF
X1
X2
FUSE
1/2 AMP
ON
INDICATOR
LAMP
OFF
MANUAL
AUTO
5
1
7
7
1
G
11
12
24
CONTACTOR
5 HP
4
O/L
23
1
1
3
6
M
A1
A2
96
95
14 13
WARNING
1
4
3
2
CONTROL BOX INSTALLATION IS TO BE
PERFORMED BY A LICENSED ELECTRICIAN
OR QUALIFIED PERSONNEL.
TERMINAL
BLOCK
THE POSSIBILITY OF ELECTRICAL SHOCK
OR ELECTROCUTION EXISTS, WHICH COULD
CAUSE SEVERE BODILY HARM EVEN DEATH!.
STOP
FLOAT
SWITCH
START
FLOAT
SWITCH
DETAIL “A”
NOTES
SINGLE PHASE INSTALLATION
L1
L2
L1
L2
The transformer connections must be set up for
230 volts. Reference detail “A”. Add the supplied
jumper wire between terminal 4 of the electronic
overload unit and L3 on the input terminal block.
230V INPUT
460V INPUT
JUMPER
TAB
H2 H4
H1 H3
H4
H1 H3
H2
ELECTRONIC OVERLOAD MODULE
SERIES
CONNECTION
PARALLEL
CONNECTION
This control box is equipped with an electronic
overload unit. The FLC (A) dial on the overload
module must be set in accordance with the require-
ments of the pump.
Figure 26. CB200 Wiring Diagram
st3020b1/bCUL sUb. pUmp • operation and parts manUaL — rev. #2 (10/28/10) — page 29
Download from Www.Somanuals.com. All Manuals Search And Download.
explanatiOn Of cOde in reMarks cOluMn
The following section explains the different symbols and
QtY. Column
remarks used in the Parts section of this manual. Use the
help numbers found on the back page of the manual if there
are any questions.
numbers Used — Item quantity can be indicated by a
number, a blank entry, or A/R.
A/R (As Required) is generally used for hoses or other
parts that are sold in bulk and cut to length.
NOTICE
The contents and part numbers listed in the parts
section are subject to change without notice.Multiquip
does not guarantee the availability of the parts listed.
A blank entry generally indicates that the item is not sold
separately.Other entries will be clarified in the“Remarks”
Column.
sampLe parts List
remarKs Column
no. part no. part name
QtY. remarKs
Some of the most common notes found in the “Remarks”
Column are listed below. Other additional notes needed
to describe the item can also be shown.
1
2%
12345
BOLT .....................1 .....INCLUDES ITEMS W/%
WASHER, 1/4 IN. ..........NOT SOLD SEPARATELY
WASHER, 3/8 IN. ..1 .....MQ-45T ONLY
2% 12347
3
4
12348
12349
HOSE ..................A/R ...MAKE LOCALLY
BEARING ..............1 .....S/N 2345B AND ABOVE
Assembly/Kit — All items on the parts list with the
same unique symbol will be included when this item is
purchased.
no. Column
Indicated by:
Unique Symbols — All items with same unique
symbol
“INCLUDES ITEMS W/(unique symbol)”
(@, #, +, %, or >) in the number column belong to the
same assembly or kit, which is indicated by a note in the
“Remarks” column.
serial number break — Used to list an effective serial
number range where a particular part is used.
Indicated by:
duplicate item numbers — Duplicate numbers indicate
multiple part numbers, which are in effect for the same
general item, such as different size saw blade guards in
use or a part that has been updated on newer versions
of the same machine.
“S/N XXXXX AND BELOW”
“S/N XXXX AND ABOVE”
“S/N XXXX TO S/N XXX”
specific model number Use — Indicates that the part
is used only with the specific model number or model
number variant listed. It can also be used to show a
part is NOT used on a specific model or model number
variant.
NOTICE
When ordering a part that has more than one item
number listed, check the remarks column for help in
determining the proper part to order.
Indicated by:
“XXXXX ONLY”
“NOT USED ON XXXX”
part no. Column
numbers Used — Part numbers can be indicated by a
number, a blank entry, or TBD.
“make/obtain Locally” — Indicates that the part can
be purchased at any hardware shop or made out of
available items.Examples include battery cables, shims,
and certain washers and nuts.
TBD (To Be Determined) is generally used to show a
part that has not been assigned a formal part number
at the time of publication.
“not sold separately”— Indicates that an item cannot
be purchased as a separate item and is either part of an
assembly/kit that can be purchased, or is not available
for sale through Multiquip.
A blank entry generally indicates that the item is not sold
separately or is not sold by Multiquip. Other entries will
be clarified in the “Remarks” Column.
page 30 — st3020b1/bCUL sUb. pUmp • operation and parts manUaL — rev. #2 (10/28/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
suggested spare parts
st3020b1/st3020bCUL sUbmersibLe pUmp
1to 3 Units
Qty.
p/n
description
1 ...........0203020B1120 .....AC CORD WITH GLAND
1............0202020060..........MECHANICAL SEAL
1............0203020B1103 .....PACKING
NOTICE
Part numbers on this Suggested Spare Parts list may
supersede/replace the part numbers shown in the
following parts lists.
st3020b1/bCUL sUb. pUmp • operation and parts manUaL — rev. #2 (10/28/10) — page 31
Download from Www.Somanuals.com. All Manuals Search And Download.
puMp assy.
127
877
436
265
266
120
236
121
104
123
122
263
102
60
8
125
103
214-2
174
65
1
81
76
160
47
3
214-1
53
4
224
129
2
322
132
179
176
131
119
177
31
33
6
130
32
146
445
90 µF
@400 VAC
147
446
page 32 — st3020b1/bCUL sUb. pUmp • operation and parts manUaL — rev. #2 (10/28/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
puMp assy.
no.
1
2
3
4
6
8
31
32
33
47
53
part no.
part name
CASING
FRICTION DISC
IMPELLER
IMPELLER NUT
IMPELLER KEY
CASING COVER
STUD BOLT
NUT
QtY.
remarKs
0202020B001
0202020B002
0202020B003
0202020004
1
1
1
1
1
1
3
3
3
0202020B006
0202020B008
0202020B031
0202020B032
0202020B003
0202020047
0202020053
0202020060
0202020065
0202020B076
0202020081
0203020B1102
0203020B1103
0203020B1104
0203020B1119
0203020B1120
0202020B1121
0202020B1122
0202020B1123
0202020B1125
0203020B1127
0203020B1129
0202020B130
0202020B131
0202020B132
0202020B146
0202020B147
0201503160
WASHER
LINER ................................................................1................QTY. AS REQUIRED
WASHER
1
1
1
4
1
1
1
2
1
1
1
1
1
2
1
1
1
4
4
1
3
1
1
1
4
1
1
1
1
1
2
2
2
2
2
1
1
4
60
65
76
81
MECHANICAL SEAL
OIL PLUG
SCREW
OIL SEAL
DISCHARGE PORT
PACKING
STUD BOLT
MOTOR
AC CORD W/CORD GLAND
CORD CLAMP
HANGER METAL
CHAIN
102
103
104
119
120
121
122
123
125
127
129
130
131
132
146
147
160
174
176
177
179
SCREW
CARRYING HANDLE
MOTOR HEAD COVER
O-RING
BOLT
SPRING WASHER
STRAINER
BOLT
SLEEVE
0203020B1174
0202020B176
0202020B177
0202020B178
OUTER PIPE
SUCTION COVER
BOLT
PACKING
214-1 0203020B1214A PACKING
214-2 0203020B1214B PACKING
224
236
263
265
266
322
436
445
446
877
0202020224
PLUG
S-TIP
WASHER
0201503A236
0203020B1263
020-3020B1265 BOLT
0203020B1266
0202020B322
0203020B1436
0203020B1445
0203020B1446
0203020B1877
WASHER
NUT
WASHER
CAPACITOR
AUTO-CUT PROTECTOR
NUT
st3020b1/bCUL sUb. pUmp • operation and parts manUaL — rev. #2 (10/28/10) — page 33
Download from Www.Somanuals.com. All Manuals Search And Download.
MOtOr assy.
page 34 — st3020b1/bCUL sUb. pUmp • operation and parts manUaL — rev. #2 (10/28/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
MOtOr assy.
no.
129
130
131
132
268
269
270
273
322
445
446
540
606
607
608
part no.
part name
MOTOR HEAD COVER
PACKING
BOLT
SPRING WASHER
MOTOR A BRACKET
MOTOR B BRACKET
MOTOR ROTOR
MOTOR STATOR
NUT
CAPACITOR
AUTO CUT PROTECTOR
PACKING
QtY.
1
1
4
4
1
1
1
1
4
1
1
2
1
1
2
remarKs
0203020B1129
0203020B1130
0202020B131
0202020B132
0202020B268
0202020B269
0203020B1270
0203020B1273
0202020B322
0203020B1445
0203020B1446
0201503A540
0202020B606
0202020B607
0202020B608
MOTOR A BEARING
MOTOR B BEARING
WAVE WASHER
st3020b1/bCUL sUb. pUmp • operation and parts manUaL — rev. #2 (10/28/10) — page 35
Download from Www.Somanuals.com. All Manuals Search And Download.
terMs and cOnditiOns Of sale — parts
5. Parts must be in new and resalable
condition, in the original Multiquip
package (if any), and with Multiquip part
numbers clearly marked.
Multiquip reserves the right to quote and
sell direct to Government agencies, and to
Original Equipment Manufacturer accounts
who use our products as integral parts of their
own products.
paYment terms
Terms of payment for parts are net 30 days.
FreigHt poLiCY
6. The following items are not returnable:
All parts orders will be shipped collect or
prepaid with the charges added to the invoice.
All shipments are F.O.B. point of origin.
Multiquip’s responsibility ceases when a
signed manifest has been obtained from the
carrier, and any claim for shortage or damage
must be settled between the consignee and
the carrier.
a. Obsolete parts. (If an item is in the
price book and shows as being
replaced by another item, it is
obsolete.)
speCiaL eXpediting serviCe
A $35.00 surcharge will be added to the
invoice for special handling including bus
shipments, insured parcel post or in cases
where Multiquip must personally deliver the
parts to the carrier.
b. Any parts with a limited shelf life
(such as gaskets, seals, “O” rings,
and other rubber parts) that were
purchased more than six months
prior to the return date.
Limitations oF seLLer’s LiabiLitY
minimUm order
Multiquip shall not be liable hereunder for
damages in excess of the purchase price of
the item with respect to which damages are
claimed, and in no event shall Multiquip be
liable for loss of profit or good will or for any
other special, consequential or incidental
damages.
The minimum charge for orders from Multiquip
is $15.00 net. Customers will be asked for
instructions regarding handling of orders not
meeting this requirement.
c. Any line item with an extended
dealer net price of less than
$5.00.
d. Special order items.
retUrned goods poLiCY
Return shipments will be accepted and
credit will be allowed, subject to the following
provisions:
e. Electrical components.
f. Paint, chemicals, and lubricants.
g. Decals and paper products.
h. Items purchased in kits.
Limitation oF Warranties
No warranties, express or implied, are
made in connection with the sale of parts or
trade accessories nor as to any engine not
manufactured by Multiquip. Such warranties
made in connection with the sale of new,
complete units are made exclusively by a
statement of warranty packaged with such
units, and Multiquip neither assumes nor
authorizes any person to assume for it
any other obligation or liability whatever in
connection with the sale of its products. Apart
from such written statement of warranty,
there are no warranties, express, implied or
statutory, which extend beyond the description
of the products on the face hereof.
1. A Returned Material Authorization
must be approved by Multiquip prior to
shipment.
7. The sender will be notified of any material
received that is not acceptable.
8. Such material will be held for five
working days from notification, pending
instructions. If a reply is not received
within five days, the material will be
returned to the sender at his expense.
2. To obtain a Return Material Authorization,
a list must be provided to Multiquip
Parts Sales that defines item numbers,
quantities, and descriptions of the items
to be returned.
9. Credit on returned parts will be issued
at dealer net price at time of the original
purchase, less a 15% restocking
charge.
a. The parts numbers and descriptions
must match the current parts price
list.
b. The list must be typed or computer
generated.
10. In cases where an item is accepted, for
which the original purchase document
can not be determined, the price will be
based on the list price that was effective
twelve months prior to the RMA date.
c. The list must state the reason(s)
for the return.
Effective: February 22, 2006
d. The list must reference the sales
order(s) or invoice(s) under
which the items were originally
purchased.
11. Credit issued will be applied to future
purchases only.
priCing and rebates
e. The list must include the name
and phone number of the person
requesting the RMA.
Prices are subject to change without prior
notice. Price changes are effective on a
specific date and all orders received on or
after that date will be billed at the revised price.
Rebates for price declines and added charges
for price increases will not be made for stock
on hand at the time of any price change.
3. AcopyoftheReturnMaterialAuthorization
must accompany the return shipment.
4. Freight is at the sender’s expense. All
parts must be returned freight prepaid to
Multiquip’s designated receiving point.
page 36 — st3020b1/bCUL sUb. pUmp • operation and parts manUaL — rev. #2 (10/28/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
nOtes
st3020b1/bCUL sUb. pUmp • operation and parts manUaL — rev. #2 (10/28/10) — page 37
Download from Www.Somanuals.com. All Manuals Search And Download.
OperatiOn and parts Manual
HERE’S HOW TO GET HELP
PLEASE HAVE THE MODEL AND SERIAL
NUMBER ON-HAND WHEN CALLING
UNITED STATES
Multiquip Corporate Office
MQ Parts Department
18910 Wilmington Ave.
Carson, CA 90746
Contact: [email protected]
Tel. (800) 421-1244
Fax (800) 537-3927
800-427-1244
310-537-3700
Fax: 800-672-7877
Fax: 310-637-3284
Mayco Parts
Warranty Department
800-306-2926
310-537-3700
Fax: 800-672-7877
Fax: 310-637-3284
800-421-1244, Ext. 279
310-537-3700, Ext. 279
Fax: 310-537-1173
Fax: 310-631-5032
Service Department
Technical Assistance
800-421-1244
310-537-3700
Fax: 310-537-4259
800-478-1244
MEXICO
UNITED KINGDOM
MQ Cipsa
Multiquip (UK) Limited Head Office
Carr. Fed. Mexico-Puebla KM 126.5
Momoxpan, Cholula, Puebla 72760 Mexico
Contact: [email protected]
Tel: (52) 222-225-9900
Fax: (52) 222-285-0420
Unit 2, Northpoint Industrial Estate, Tel: 0161 339 2223
Fax: 0161 339 3226
Global Lane,
Dukinfield, Cheshire SK16 4UJ
Contact: [email protected]
Canada
Multiquip
4110 Industriel Boul.
Laval, Quebec, Canada H7L 6V3
Contact: [email protected]
Tel: (450) 625-2244
Tel: (877) 963-4411
Fax: (450) 625-8664
© COPYRIGHT 2010, MULTIQUIP INC.
Multiquip Inc and the MQ logo are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without written permission. All other trademarks are the property
of their respective owners and used with permission.
This manual MUST accompany the equipment at all times. This manual is considered a permanent part of the equipment and should remain with the unit if resold.
The information and specifications included in this publication were in effect at the time of approval for printing. Illustrations, descriptions, references and technical data contained in
this manual are for guidance only and may not be considered as binding. Multiquip Inc. reserves the right to discontinue or change specifications, design or the information published
in this publication at any time without notice and without incurring any obligations.
Your Local Dealer is:
Download from Www.Somanuals.com. All Manuals Search And Download.
|