OPERATION AND PARTS MANUAL
MODEL GA-2.5H
PORTABLE AC GENERATOR
(HONDA GASOLINE ENGINE)
S/N 5496762 AND BELOW
S/N 5496763 AND ABOVE
Revision #5 (03/04/08)
To find the latest revision of this
publication, visit our website at:
THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.
Download from Www.Somanuals.com. All Manuals Search And Download.
PAGE 2 — GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE PAGE
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 3
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
MQ GA-2.5H — AC
Portable Generator
Honda GX160K1EMA2
Gasoline Engine
Proposition 65 Warning ..............................................2
Table Of Contents ......................................................4
Parts Ordering Procedures ........................................5
Safety Alert Message Symbols .............................. 6-7
Rules for Safe Operation...................................... 8-10
Specifications (Generator) .......................................11
Specifications (Engine) ............................................12
Dimensions ..............................................................13
General Information .................................................14
Load Application ......................................................15
Controls and Indicators ...................................... 16-17
Generator Refueling.................................................18
Installation .......................................................... 19-20
Pre-Inspection ..........................................................21
Pre-Inspection (Engine) ...........................................22
Initial Start-up (Engine) ............................................23
Initial Start-up (Engine/Operation) ...........................24
Preparation For Long Term Storage .........................25
Maintenance....................................................... 26-27
Wiring Diagram S/N 5496762 & below) ...................28
Wiring Diagram (S/N 5496763 & above) ..................29
Troubleshooting (Engine) ................................... 30-31
Troubleshooting (Generator) ....................................32
Explanation Of Codes In Remarks Column .............34
Suggested Spare Parts ............................................35
Cylinder Head Assembly.................................... 48-49
Cylinder Barrel Assembly ................................... 50-51
Crankcase Cover Assembly ............................... 52-53
Crankshaft Assembly ......................................... 54-55
Piston Assembly................................................. 56-57
Camshaft Assembly ........................................... 58-59
Recoil Starter Assembly..................................... 60-61
Fan Cover Assembly .......................................... 62-63
Carburetor Assembly ......................................... 64-65
Air Cleaner Assembly......................................... 66-67
Muffler Assembly................................................ 68-69
Flywheel Assembly ............................................ 70-71
Ignition Coil Assembly........................................ 72-73
Governor/Control Assembly ............................... 74-75
Labels................................................................. 76-77
Terms and Conditions Of Sale — Parts ...................78
Generator Component
Drawings
Nameplate and Decals....................................... 36-37
Generator Assembly .......................................... 38-39
Control Box Assembly (S/N 5496762 & below).. 40-41
Control Box Assembly (S/N 5496763 & above) . 42-43
Pipe Frame Assembly (S/N 5496762 & below) .. 44-45
Pipe Frame Assembly (S/N 5496763 & above).. 46-47
PAGE 4 — GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS ORDERING PROCEDURES
Ordering parts has never been easier!
Choose from three easy options:
Effective:
January 1st, 2006
Best Deal!
Order via Internet (Dealers Only)
Orderpartson-lineusingMultiquip’sSmartEquipwebsite!
:
If you have an MQ Account, to obtain a
Username and Password, E-mail us at:
■
■
■
View Parts Diagrams
Order Parts
PrintSpecificationInformation
To obtain an MQ Account, contact your
District Sales Manager for more information.
Use the internet and qualify for a 5% Discount
on Standard orders for all orders which include
complete part numbers.*
Gotowww.multiquip.comandclickon
to log in and save!
Order Parts
Note: Discounts Are Subject To Change
Fax your order in and qualify for a 2% Discount
on Standard orders for all orders which include
complete part numbers.*
Order via Fax (Dealers Only)
:
All customers are welcome to order parts via Fax.
Domestic (US) Customers dial:
1-800-6-PARTS-7 (800-672-7877)
Note: Discounts Are Subject To Change
Domestic (US) Dealers Call:
1-800-427-1244
Order via Phone:
Non-Dealer Customers:
International Customers should contact
their local Multiquip Representatives for
Parts Ordering information.
Contact your local Multiquip Dealer for
parts or call 800-427-1244 for help in
locating a dealer near you.
When ordering parts, please supply:
❒
Specify Preferred Method of Shipment:
❒
❒
❒
❒
❒
❒
Dealer Account Number
✓
UPS/Fed Ex
✓ DHL
Dealer Name and Address
■
■
Priority One
Ground
✓
Truck
Shipping Address (if different than billing address)
Return Fax Number
Applicable Model Number
■ Next Day
■
Second/ThirdDay
Quantity, Part Number and Description of Each Part
All orders are treated asStandard Orders
andwillshipthesamedayifreceivedprior
to 3PM PST.
WE ACCEPT ALL MAJOR CREDIT CARDS!
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 5
Download from Www.Somanuals.com. All Manuals Search And Download.
GA-2.5H — SAFETY MESSAGE ALERT SYMBOLS
HAZARD SYMBOLS
FOR YOUR SAFETY AND THE SAFETY OF OTHERS!
Potential hazards associated with the operation of a MQ
GA-2.5H Portable Generator will be referenced with Hazard
Symbols which appear throughout this manual, and will be
referenced in conjunction with Safety Message Alert
Symbols.
Safety precautions should be followed
at all times when operating this
equipment. Failure to read and
understand the Safety Messages and
Operating Instructions could result in
injury to yourself and others.
Lethal Exhaust Gas Hazards
WARNING
This Owner's Manual has been
developed to provide complete
instructions for the safe and efficient
Engine exhaust gases contain
poisonous carbon monoxide. This gas
is colorless and odorless, and can cause
death if inhaled. NEVER operate this
equipment in a confined area or
enclosed structure that does not provide
ample free flow air.
operation of the MQ Model GA-2.5H
Portable Generator. Refer to the
engine manufacturers instructions for
data relative to its safe operation.
Before using this generator, ensure that the operating
individual has read and understands all instructions in this
manual.
Explosive Fuel Hazards
SAFETY MESSAGE ALERT SYMBOLS
WARNING
Gasoline is extremely flammable, and
its vapors can cause an explosion if
ignited. DO NOT start the engine near
spilled fuel or combustible fluids.
The three (3) Safety Messages shown below will inform you about
potential hazards that could injure you or others. The Safety
Messages specifically address the level of exposure to the
operator, and are preceded by one of three words: DANGER,
DO NOT fill the fuel tank while the engine is running or
hot. DO NOT overfill tank, since spilled fuel could ignite if
it comes into contact with hot engine parts or sparks from
the ignition system. Store fuel in approved containers, in
well-ventilated areas and away from sparks and flames.
DANGER
You WILL be KILLED or SERIOUSLY INJURED if
you DO NOT follow these directions.
Burn Hazards
WARNING
WARNING
Engine components can generate extreme
heat. To prevent burns, DO NOT touch
these areas while the engine is running or
immediately after operations. Never
operate the engine with heat shields or
heat guards removed.
You CAN be KILLED or SERIOUSLY INJURED if
you DO NOT follow these directions.
CAUTION
You CAN be INJURED if you DO NOT follow
these directions.
Respiratory Hazards
WARNING
ALWAYS wear approved respiratory
protection when required.
PAGE 6 — GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
GA-2.5H — SAFETY MESSAGE ALERT SYMBOLS
Equipment Damage
Rotating Parts Hazards
CAUTION
CAUTION
Hazards
NEVER operate equipment with covers,
or guards removed. Keep fingers, hands,
hair and clothing away from all moving
parts to prevent injury.
Other important messages are provided throughout this
manual to help prevent damage to your portable generator,
other property, or the surrounding environment.
Accidental Starting Hazards
CAUTION
ALWAYS place the power source, circuit
breakers or ON/OFF switch in the OFF
position, when the generator is not in use,
unless connected to transfer switch.
Eye and Hearing Hazards
CAUTION
ALWAYS wear approved eye and
hearing protection.
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 7
Download from Www.Somanuals.com. All Manuals Search And Download.
GA-3.6H— RULES FOR SAFE OPERATION
■
NEVER touch the hot exhaust
manifold, muffler or cylinder. Allow
these parts to cool before servicing
engine or generator.
Read this manual!
DANGER
Failure to follow instructions in this manual may lead
to serious injury or even death! This equipment is to
be operated by trained and qualified personnel only!
This equipment is for industrial use only.
The following safety guidelines should always be used when
operating the MQ GA-2.5H Portable Generator:
■
The engine section of this generator requires an adequate
free flow of cooling air. NEVER operate the generator in
any enclosed or narrow
area where free flow of the
air is restricted. If the air
GENERAL SAFETY
■
DO NOT operate or service this
equipment before reading this entire
manual.
flow is restricted it will
cause serious damage to
the generator or engine
and may cause injury to
people. Remember the
generator's engine gives
off DEADLY carbon
■
■
This equipment should not be operated by persons under
18 years of age.
NEVER operate this equipment without proper protective
clothing, shatterproof glasses, steel-toed boots and other
protective devices required by the job.
monoxide gas.
■
■
ALWAYS refuel in a well-ventilated area, away from sparks
and open flames.
■
■
NEVER operate this equipment when not
feeling well due to fatigue, illness or taking
medicine.
ALWAYS use extreme caution when
working with flammable liquids. When
refueling, stop the engine and allow it
to cool. DO NOT smoke around or near
the machine. Fire or explosion could
result from fuel vapors, or if fuel is spilled
on a hot engine.
NEVER operate this equipment under the influence of
drugs or alcohol.
■
NEVER operate the generator in an
explosive atmosphere or near
combustible materials. An explosion or
fire could result causing severe bodily
harm or even death.
■
ALWAYS wear proper respiratory (mask),
hearing and eye protection equipment when
operating the generator.
■
■
■
Whenever necessary, replace nameplate, operation and
safety decals when they become difficult read.
■
NEVER disconnect any "emergency or safety devices".
These devices are intended for operator safety. Disconnection
of these devices can cause severe injury, bodily harm or even
death! Disconnection of any of these devices will void all
warranties.
Manufacturer does not assume responsibility for any
accident due to equipment modifications.
NEVER use accessories or attachments, which are not
recommended by Multiquip for this equipment. Damage
to the equipment and/or injury to user may result.
PAGE 8 — GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
GA-2.5H — RULES FOR SAFE OPERATION
■
■
■
ALWAYS be sure the operator is familiar with proper safety
precautions and operation techniques before using generator.
Maintenance Safety
■
NEVER lubricate components or attempt service on a
running machine.
NEVER leave the generator unattended, turn off engine when
unattended.
■
High Temperatures – Always stop engine
and allow the engine to cool before adding
fuel, oil or performing service and
maintenance functions. Contact with hot!
components can cause serious burns.
Unauthorized equipment modifications will void all
warranties.
■
■
ALWAYS ensure generator is on level ground before use.
DO NOT place hands or fingers inside generator engine
compartment when engine is running.
■
■
Keep the machinery in proper running condition.
Fix damage to the machine immediately and replace any
broken parts immediately.
■
■
NEVER run engine without air cleaner.Severe engine damage
may occur.
■
■
ALWAYS replace any worn or damaged warning decals.
NEVER change or adjust the engine speed which has been
set at the factory prior to shipping.
ALWAYS store equipment properly when it is not being used.
Equipment should be stored in a clean, dry location out of the
reach of children and un-authorized personnel.
Power Cord Safety
■
NEVER let power cables or cords lay in water.
■
The electrical voltage required to operate the generator can
cause severe injury or even death through physical contact
with live circuits. Turn all circuit breakers OFF before
performing maintenance on the generator.
■
NEVER stand in water while AC power from the generator
is being transfer to a load.
■
■
■
NEVER use a defective or frayed power cable. Check the
cable for cuts in the insulation.
■
■
Dispose of hazardous waste properly. Examples of
potentially hazardous waste are used motor oil, fuel and
fuel filters.
NEVER use a extension cord that is frayed or damaged
where the insulation has been cut.
DO NOT use food or plastic containers to dispose of
hazardous waste.
ALWAYS make certain that proper power or extension cord
has been selected for the job See Table 3.
■
■
DO NOT pour waste, oil or fuel directly onto the ground,
down a drain or into any water source.
Removing the engine oil drain plug while
the engine is hot will result in hot oil to gush
out of the oil drain plug, therefore causing
severe scalding to any persons in the
general area of the generator.
Grounding Safety
■
ALWAYS make sure that electrical circuits are properly
grounded per the National Electrical Code (NEC) and
local codes before operating generator. Severe injury or
death! by electrocution can result from operating an
ungrounded generator.
■
■
ALWAYS make sure generator is properly grounded to a
suitable earth ground (GROUND ROD). See installation in
this manual.
NEVER use gas piping as an electrical ground.
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 9
Download from Www.Somanuals.com. All Manuals Search And Download.
GA-2.5H — RULES FOR SAFE OPERATION
Emergencies
DANGER-ELECTROCUTION HAZARDS
■
ALWAYS know the location of the
nearest fire extinguisher.
During operation of this generation, there
exists the possibility of electrocution,
electrical shock or burn, which can
cause severe bodily harm or even
DEATH!
■
■
ALWAYS know the location of the nearest
first aid kit.
To avoid these hazards:
NEVER use damaged or worn cables when connecting
equipment to the generator.Make sure power connecting
cables are securely connected to the generator’s output
receptacles, incorrect connections may cause damage
to the generator and electrical shock.
In emergencies always know the location of the
nearest phone or keep a phone on the job site.
Also know the phone numbers of the nearest
ambulance, doctor and fire department. This
information will be invaluable in the case of an
emergency.
NEVER grab or touch a live
power cord with wet hands, the
possibility exist of electrical
shock, electrocution, and even
death!
NEVER insert any objects into
the output receptacles during
operation. This is extremely
dangerous. ALWAYS turn-off
the generator and place all circuit breakers in the “OFF”
position when contact with the output receptacles is
required. There exist the possibility of electrocution,
electrical shock or burn, which can cause severe
bodily harm or even death!
Backfeed to a utility system can cause
electrocution and or property damage.
NEVER connect the generator to a
building's electrical system without a
transfer switch or other approved
device. All installations should be
performed by a licensed electrician
in accordance with all applicable laws
and electrical codes. Failure to do so
could result in electrical shock or burn
causing serious injury or even death!
PAGE 10 — GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
GA-2.5H — SPECIFICATIONS (GENERATOR)
GA-2.5H — OPERATION AND SAFETY DECALS
Table 1. Specifications (Generator)
Model
GA-2.5H
Type
Brushless Revolving Field Type
Excitation
Solid State, Statically Excited System
AC Generator
Speed
3,600 RPM
Self-Ventilation
3.17 gallons (12 liters)
2.2 kW
Cooling System
Fuel Capacity
Continuous Output
Stanby Output
Rated Voltage
Current Max/Continuous (120V)
Phase
2.5 kW
120V
60 Cycle AC Power
Source
20.8/18.3 amps
Single Phase (3-wire)
60 Hz
Frequency
Power Factor
1
20.0 x 16.1 X 18.5 in.
(510 X 410 X 470 mm)
Dimensions Approximate
(L x W x H)
110 lbs. (50 kg.)
132 lbs. (60 kg.)
Dry Net Weight
Weight (With Fuel)
Effects of Altitude and Heat
The maximum output of the engines listed above are applicable to supplying electrical power for continuous service at ambient
conditions in accordance with SAE Test cord J607. The above ambient conditions are at standard sea level, with a barometric
reading of 29.92 inches and a temperature of 60 degrees fahrenheit.
Generally, the engine's output power will decrease 3-1/2% for each 1000 feet of altitude above sea level, and 1% for each 10°
F Fahrenheit above the standard temperature of 60° F
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 11
Download from Www.Somanuals.com. All Manuals Search And Download.
GA-2.5H — SPECIFICATIONS (ENGINE)
Table 2. Specifications (Engine)
Model
HONDA GX-160K1EMA2
Air-cooled 4 stroke, Single
Cylinder, OHV, Horizontal
Shaft Gasoline Engine
Type
2.7 in. x 1.8 in.
(68 mm x 45 mm)
Bore X Stroke
Displacement
Max Output
163 cc (9.9 cu-in)
5.5 H.P./3600 R.P.M.
Engine/Electric Motor
Approx. 0.95 U.S. gallons
(3.6 liters)
Fuel Tank Capacity
Unleaded Automobile
Gasoline
Fuel
Lube Oil Capacity
Speed Control Method
Starting Method
0.63 qts. (.60 liters)
Centrifugal Fly-weight
Type
Recoil Start
12.0 X 14.4 X 13.2 in.
(304 X 362 X 335 mm)
Dimension (L x W x H)
Dry Net Weight
33.1 lbs. (15 Kg.)
In keeping with Multiquip's policy of
constantly improving its products, the
specifications quoted herein are subject
to change without prior notice.
PAGE 12 — GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
GA-2.5H — DIMENSIONS
Figure 1. Dimensions
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 13
Download from Www.Somanuals.com. All Manuals Search And Download.
GA-2.5H — GENERAL INFORMATION
Excitation System
WARNING
Before connecting this generators to any building’s
electrical system, a licensed electrician must install an
isolation (transfer) switch.
The GA-2.5H generator uses a magnet attached to a
flywheel to produce AC voltage from a lamp coil beneath
the flywheel. As the magnetic passes the coil it produces
approximately 19-22 AC volts.
This voltage (19-22 VAC) is then sent to the control box that
contains three rectifying diodes:
Serious injury or death may result without this transfer
switch.
z
z
z
Excitation (diode 1)
Battery (diode 2)
Slow Down (diode 3)
GA-2.5H FAMILIARIZATION
Generator
The AC voltage will pass through the excitation diode that
converts the voltage to DC power.
The Multiquip GA-2.5H generator has been designed as a
portable dual purpose power source for 60 Hz (single phase)
lighting facilities, power tools, submersible pumps and other
industrial and construction machinery.
This DC power is then sent to the excitation windings housed
within the main windings commonly called the "stator".
This voltage is then transferred into the rotor through
induction.The rotor contains two diodes within it which rectify
the DC voltage and send it out through the main windings,
as AC voltage.
These generators are mounted on rubber vibration isolators
that have a steel base backplate which is attached to the
protective steel pipe carrying frame.The protective carrying
frame is made of steel tubing and fully wraps around the
generators to protect against damage. See Figures 2A and
2B for the basic controls and indicators for the GA-2.5H
generator.
Alternator
The alternator, a brushless revolving-field type, is
permanently aligned to the engine through rigid coupling.
This portable generator is supplied with a electrical control
box. To reduce vibration caused by the engine, the control
box is also placed on rubber isolators.
Engine
This generator is powered by a 5.5 HP, air-cooled, 4-stroke
HONDA gasoline engine. Reference Table 2, for engine
specifications.
Control Box
The control box is provided with the following:
■
120V twist-lock receptacle, single phase. (S/N 5496763
and above)
■
■
120V GFCI single phase duplex output receptacle
20 amp main circuit breaker
■
■
AC Voltmeter
Ground Terminal (S/N 5496762 and below)
PAGE 14 — GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
GA-2.5H — LOAD APPLICATION
Single Phase Load — 60 Hz
To determine the running wattage for your load, multiply
the running wattage as indicated by steps 1, 2, and 3 below:
Always be sure to check the nameplate on the generators
and equipment to insure the wattage, amperage and
frequency requirements are satisfactorily supplied by the
generators for operating the equipment.
1. INCANDESCENT LOADS
Lights, heaters and similar appliances.
Total the running wattage and multiply by 1.
Example:
Generally, the wattage listed on the nameplate of the
equipment is its rated output. Equipment may require 130—
150% more wattage than the rating on the nameplate, as
the wattage is influenced by the efficiency, power factor and
starting system of the equipment.
29 light bulbs @ 100W each = 2.9 KW
use a 3 KW generator.
2. SMALL MOTORS
Drills and other small power tools.
Total the running wattage and multiply by 2.
Example:
A 1 inch drill runs at 1 KW
use a 2 KW generator.
If wattage is not given on the equipment's
name plate, approximate wattage may be
determined by multiplying nameplate
voltage by the nameplate amperage.
3. LARGE MOTORS
Submersible pumps, table saws etc.
Total the running wattage and multiply by 3.
Example:
A conveyor belt runs at 8 KW
use a 24 KW generator.
WATTS = VOLTAGE x AMPERAGE
The power factor of this generators is 1.0 SeeTable 3 below
when connecting loads.
Table 3. Power Factor By Load
CAUTION
Type Of Load
Power Factor
Motors and motor-driven equipment draw much greater
current for starting than during operation. Always use
an adequate size extension cable which can carry the
required load. See Table 4.
Single-phase induction motors
0.4 - 0.75
Electric heaters, incandescent
lamps
1.0
Fluorescent lamps, mecury
lamps
0.4 - 0.9
Extension Cables
When electric power is to be provided to various tools or
loads at some distance from the generator, extension cords
are normally used. Cables should be sized to allow for
distance in length and amperage so that the voltage
drop between the generators and point of use (load) is
held to a minimum. Use the cable selection chart (Table 4 )
as a guide for selecting proper cable size.
Electronic devices,
communication equipment
1.0
0.8
Common power tools
When using a combination of dual
receptacles, total load should not
exceed the rated capacity of the
generator.
The idle control device is operated at a
minimum load capacity of 100W. If the
load capacity is less than 100W, place
the idle control switch in the OFF
position.
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 15
Download from Www.Somanuals.com. All Manuals Search And Download.
GA-2.5H — CONTROLS AND INDICATORS
Figure 2A. Generator Components
6. ON-OFF Switch – place engine ON/OFF switch in the
"ON" position for normal operation. To turn- off the
generator place switch in the "OFF" position.
1. 120V Output Receptacle – This NEMA L5- 20R twist-
lock receptacle will provide 120V, 20 amps, 60 Hz.
Applies to units with S/N 5496763 and above.
7. Chassis Ground – This ground connection point should
be connect to a good earth ground (ground rod). Applies
to units with S/N 5496763 and above.
2. GFCI Receptacle – This 5-20R duplex receptacle will
provide 120V at all times.
3. AC-Voltmeter – This voltmeter indicates (with a mark)
the rated 60 Hz, single phase output voltage. In addition
the voltmeter can also be used as a diagnostic tool. If the
voltmeter indicator (needle) is below the rated voltage,
engine problems may exist (low/high RPM's). To prevent
damage to the generator or power tools turn the generator
OFF and consult your authorized MQ service dealer.
This HONDA engine is equipped
with
a
low oil shutdown
capability. A built in sensor will
automatically turn off the engine
should the oil level fall below a
safe operating condition. Make
sure the generator is placed on
4. Ciruit Breaker – To protect the generator from an
overload, a 2- pole 20 amp circuit breaker is provided on
the control box. Make sure to place the circuit breaker to
the "OFF" postion prior to starting the engine.
level ground. Placing the generator on level ground will ensure
that the low oil sensor will function properly.
5.
GFCI Ground – This ground connection point should
be connect to a good earth ground (ground rod). Applies
to units with S/N 5496762 and below.
PAGE 16 — GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
GA-2.5H — CONTROLS AND INDICATORS
Figure 2B. Generator Components
8. Generator Housing – Contains the rotor, rectifer field 15. Fuel Cock Lever – Turn this lever downward to start
coil assembly, aramature, bearings and other components
that make up generator asembly.
(down)the flow of fuel to the carburetor. Turn upward to
stop (up) the flow of fuel.
9. Spark Plug – Provides spark to the ignition system. Set 16. Throttle Lever – Used to adjust engine RPM speed.
spark plug gap to 0.6 - 0.7 mm (0.024 - 0.028 inch).Clean
spark plug once a week.
This unit is set at the factory and is not adjustable.
17. Recoil Starter (Pull Rope) – Used for manual-starting
of the engine. Pull the starter grip until resistance is felt,
then pull briskly and smoothly.
10. Muffler/Heat Shield – Used to reduce noise and
emissions. NEVER touch this heat shield when the
generator is in use. Always allow time for the generator to
cool down before performing maintenance.
18. Engine – This generator uses a 5.5 HP HONDA air-
cooled, 4-stroke , single cylinder, overhead camshaft
gasoline engine. Engine uses unleaded gasoline.
11. Oil Dipstick/ Filler Cap– Remove the filler cap dipstick
when checking the engine oil level.Add engine oil through
19. Air Cleaner – Every 50 hours: Prevents dirt and other
debris from entering the fuel system. Remove wing-nut
on top of air filter cannister to gain access to filter element.
NEVER run the engine without an air cleaner.
12. Oil Drain Plug – Remove this plug to drain engine oil
from the crankcase.
13. Carburetor Fuel Cup – Inspect the fuel cup weekly for
water and dirt. Clean as referenced in the maintenance
section of this manual.
20. Fuel Gauge – Read this gauge to determine when fuel
is low.
14. Choke Lever – Used for starting the engine. Close the
choke lever when starting a cold engine or in cold weather
conditions. The choke enriches the fuel mixture. Open
the choke lever if starting a warm engine or in warm
weather conditions.
21. Fuel Gauge/Tank – Remove this cap to add unleaded
gasoline to the fuel tank.Replenish with clean unleaded
gasoline. Make sure cap is tightened securely. DO NOT
over fill. Fuel tank capacity is 3.2 gallons (12 liters).
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 17
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ GA-2.5H — GENERATOR REFUELING
DANGER
Adding fuel to the tank should be done only when
the engine is stopped and has had an
opportunity to cool down. In the event of a fuel spill, DO NOT
attempt to start the engine until the fuel residue has been
completely wiped up, and the area surrounding the engine is
dry. If generator is placed in a truck bed with a plastic liner,
REMOVE generator from truck bed and place on ground
(Figure 3) to refuel. This possibility exist of fire or explosion
due to static electricity.
Figure 3. Generator Refueling
PAGE 18 — GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
GA-2.5H — INSTALLATION
Outdoor Installation
Indoor Installation
Install the generator in a area that is free of debris,
bystanders, and overhead obstructions. Make sure the
generator is on secure level ground so that it cannot slide or
shift around. Also install the generator in a manner so that
the exhaust will not be discharged in the direction of nearby
homes.
Exhaust gases from gasoline engines are extremely
poisonous. Whenever an engine is installed indoors the
exhaust fumes must be vented to the outside. The engine
should be installed at least two feet from any outside wall.
Using an exhaust pipe which is too long or too small can
cause excessive back pressure which will cause the engine
to heat excessively and possibly burn the valves.
Eliminate the danger of deadly carbon monoxide gas.
Remember that exhaust fumes from any gasoline engine
are very poisonous if discharged in a closed room, but
harmless if allowed to mix with the outside air. If the
generator is installed indoors, you must make provisions
for venting the engine exhaust to the outside of the building.
The installation site must be relatively free from moisture
and dust. All electrical equipment should be protected from
excessive moisture. Failure to do will result in deterioration
of the insulation and will result in short circuits and grounding.
Foreign materials such as dust, sand, lint and abrasive
materials have a tendency to cause excessive wear to
engine and alternator parts.
Generator Grounding
To guard against electrical shock and possible damage to
the equipment, it is important to provide a good EARTH
ground. Always use the ground terminal on the generator
to ground the generator.
CAUTION
Article 250 (Grounding) of the National Electrical Code
(NEC) provides guide lines for proper grounding and
specifies that the cable ground shall be connected to the
grounding system of the building as close to the point of
cable entry as practical.
Pay close attention to ventilation when
operating the generator inside tunnels
and caves.The engine exhaust contains
noxious elements.
NEC articles 250-64(b) and 250-66 set the following
grounding requirements:
Mounting
The generator should always be mounted on a flat level
surface to isolate vibration of the generator when it is
running. DO NOT place the generator on slopes, the
possibility exists that the generator could slide.
1. Use one of the following wire types to connect the
generator to earth ground.
a. Copper - 10 AWG (5.3 mm2) or larger.
b. Aluminum - 8 AWG (8.4 mm2) or larger.
2. When grounding the generator (Figure 3) connect the
ground cable between the lock washer and the nut on
the generator and tighten the nut fully.Connect the other
end of the ground cable to earth ground.
3. NEC article 250-52(c) specifies that the earth ground
rod should be buried a minimum of 8 ft. into the ground.
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 19
Download from Www.Somanuals.com. All Manuals Search And Download.
GA-2.5H — INSTALLATION
Connecting the Ground
The nut and ground terminal on the generator should always be used to connect the generator to a suitable ground. The
ground cable should be #8 size wire minimum.
At the generator, connect the terminal of the ground cable between the lock washer and the nut (Figure 4) and tighten the
nut fully. Connect the other end of the ground cable to a suitable earth ground (ground rod).
Figure 4. Generator Grounding
PAGE 20 — GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
GA-2.5H — PRE-INSPECTION
General Inspection Prior to Operation
Ground Power Tools
Extension Cable
When electric power is to be provided to various tools or loads
at some distance from the generator, extension cords are
normally used. Cables should be sized to allow for distance in
length and amperage so that the voltage drop between the
generator and point of use (load) is held to a minimum. Use
the cable selection chart (Table 4) as a guide for selecting
proper cable size.
When using power tools or electrical equipment requireing AC
power from the generator, make sure connecting (power tool)
cable (Figure 5) has a ground as shown in Figure.
Never! use power tools or
equipment that do not have a
ground capability, the possibility
exists of electrocution, electrical
shock or burn, which can cause
severe bodily harm or even
DEATH!
Main Circuit Breaker
To protect the generator from an overload always place the
main circuit breaker in the "OFF" position prior to starting the
engine.
Figure 5. Ground Cables/Plugs
Table 4. Cable Selection (60 Hz, Single Phase Operation)
Load In
Watts
Maximum Allowable Cable Length
Current in
Amperes
At 120
Volts
#10 Wire
#12 Wire
#14 Wire
#16 Wire
2.5
5
300
600
1000 ft.
500 ft.
350 ft.
250 ft.
150 ft.
125 ft.
600 ft.
300 ft.
200 ft.
150 ft.
100 ft.
75 ft.
375 ft.
200 ft.
125 ft.
100 ft.
65 ft.
250 ft.
125 ft.
100 ft.
7.5
10
15
20
900
1200
1800
2400
50 ft.
CAUTION: Equipment damage can result from low voltage.
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 21
Download from Www.Somanuals.com. All Manuals Search And Download.
GA-2.5H — PRE-INSPECTION (ENGINE)
CAUTION
NEVER operate the generator in a
confined area or enclosed area structure
that does not provide ample free flow of
air.
Figure 7. Engine Oil Dipstick (Oil Level)
Table 5. Oil Type
ALWAYS wear approved eye and hearing
protection before operating the generator.
Before Starting
Season
Summer
Spring/Fall
Winter
Temperature
25°C or Higher
25°C~10°C
Oil Type
SAE 10W-30
SAE 10W-30/20
SAE 10W-10
1. Read safety instructions at the
beginning of manual.
2. Clean the generator, removing
dirt and dust, particularly the
engine cooling air inlet, carburetor
and air cleaner.
0°C or Lower
DANGER EXPLOSIVE FUEL
3. Check the air filter for dirt and dust. If air filter is dirty,
replace air filter with a new one as required.
Motor fuels are highly flammable and can
be dangerous if mishandled.DO NOT smoke
while refueling. DO NOT attempt to refuel
the generator if the engine is hot! , running
or in the dark.
4. Check carburetor for external dirt and dust. Clean with
dry compressed air.
5. Check fastening nuts and bolts for tightness.
Engine Oil Check
1. To check the engine oil level, place the generator on
secure level ground with the engine stopped.
Fuel Check
1. Close the fuel cock before filling the fuel tank.
2. Remove the fuel cap located on top of fuel tank.
2. Remove the filler dipstick from the engine oil filler hole
(Figure 6) and wipe clean.
3. Read the fuel gauge located on top of the fuel tank (Figure 8)
to determin if the fuel level is low. If fuel is low, replenish
with clean unleaded fuel.
Figure 8. Fuel Gauge
Figure 6. Engine Oil Dipstick (Removal)
3. Insert and remove the dipstick without screwing it into the
filler neck. Check the oil level shown on the dipstick.
4. When refueling, be sure to use a strainer for filtration. DO
NOT top-off fuel. DO NOT fill the tank beyond capacity.
Wipe up any spilled fuel immediately!
4. If the oil level is low (Figure 7), fill to the edge of the oil filler
holewiththerecommendedoiltype(Table5).Maximum oil
capacity is .63 quarts (0.6 liters)
PAGE 22 — GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
GA-2.5H — INITIAL START-UP (ENGINE)
3. Place the choke lever (Figure 11) in the "OPEN " position
if starting a warm engine or the temperature is warm.
CAUTION
DO NOT attempt to operate this
generator until the Safety, General
Information and Inspection sections
of this manual have been read and
thoroughly understood.
4. Place the engine ON/OFF switch (Figure 12) in the "ON
" position.
This section is intended to assist the
operator with the initial start-up of the trash generator. It is
extremely important that this section be read carefully before
attempting to use the generator in the field.
Before Starting the Engine
Figure 12. Engine ON/OFF Switch (ON)
1. Be sure to disconnect all electrical loads from the
generator prior to starting the engine.
5. Grasp the starter grip (Figure 13) and slowly pull it out.The
resistance becomes the hardest at a certain position,
corresponding to the compression point. Pull the starter
grip briskly and smoothly for starting.
2. NEVER start the engine with the main circuit breaker
in the “ON" position. Place the main circuit breaker
(Figure 9) in the OFF position.
Figure 9. Main Breaker (OFF Position)
Starting the Engine
1. Place the engine fuel valve lever (Figure 10) to the "ON"
Figure 13. Starter Grip
position.
”
CAUTION
DO NOT pull the starter rope all the way to the end.
DO NOT release the starter knob after pulling. Allow it
to rewind as soon as possible.
Figure 10. Engine Fuel Valve Lever (ON Position)
2. Place the choke lever (Figure 11) in the "CLOSED "
position if starting a cold engine.
Figure 11. Choke Lever
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 23
Download from Www.Somanuals.com. All Manuals Search And Download.
GA-2.5H — INITIAL START-UP ENGINE/OPERATION
Stopping The Engine
6. If the engine has started, slowly return the choke lever
Normal Shutdown
(Figure 11 ) to the “OPEN” position. If the engine has not
started repeat steps 1 through 5.
1. Place the main circuit breaker (Figure 9) in the OFF
position.
7. Before the generator is placed into operation, run the
engine for 3-5 minutes. Check for abnormal smells, fuel
leaks, and noises that would associate with lose compo-
nents.
2. Remove the load from the generator, and let the engine
run at idle for 3-5 minutes with the idle control switch in
the ON position (Up)
8. Refer to the AC voltmeter (Figure 14) on the control
panel.The voltage indicated on the voltmeter should be
120 VAC with no load applied.
3. Place the engine ON/OFF switch (Figure 17) in the "OFF"
position.
Figure 17. Engine ON/OFF Switch (OFF)
Figure 14. AC Voltmeter (120 VAC)
4. Place the engine fuel valve lever (Figure 18) to the "OFF"
9. If desired, verify with a voltmeter (Figure15) that 120
VAC is present at the GFCI duplex receptacle and the
120V twist-lock receptacle.
position.
”
Figure 18. Engine Fuel Valve Lever (OFF Position)
Emergency Showdown
1. Place the engine ON/OFF swith (Figure 17) in the
"OFF" position.
Figure 15. 120 VAC GFCI Receptacle
Connecting the Load
1. Connect the load to the output receptacles.
2. Place the main circuit breaker (Figure 16) in the ON
position.
Figure 16. Main Circuit Breaker (ON)
PAGE 24 — GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ GA-2.5H — PREPARATION FOR LONG -TERM STORAGE
Generator Storage
For storage of the generating set for over 30 days, the
following is required:
■
■
Drain the fuel tank completely, or add STA-BIL to the fuel.
Run the engine until the gasoline in the carburetor is
completely consumed.
■
■
■
■
Completely drain the oil from the crankcase and refill with
fresh oil.
Remove the spark plug, pour 2 or 3 cc of SAE 30 oil into the
cylinder and crank slowly to distribute the oil.
Slowly rotate the engine a few times with the starter Rope
and install a new plug.
Pull out the starter rope slowly and stop at the compression
point.
■
■
Clean all external parts of the generating set with a cloth.
Cover the generating set and store in a clean, dry place.
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 25
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ GA-2.5H — MAINTENANCE (ENGINE)
UseTable 6 as a general maintenance guideline when servicing
your engine. For more detail engine maintenance information,
refer to the engine owner's manual supplied with your engine.
Table 6. Engine Maintenance Schedule
FIRST
EVERY
EVERY
EVERY
YEAR
OR
EVERY
2 YEARS
OR
MONTH 3 MONTHS 6 MONTHS
OR
DESCRIPTION (3)
OPERATION
BEFORE
OR
OR
10 HRS.
25 HRS.
50 HRS.
100 HRS.
200 HRS.
CHECK
CHANGE
CHECK
X
Engine Oil
X
X
X
Air Cleaner
All Nuts & Bolts
Spark Plug
CHANGE
X (1)
Re-tighten If
Necessary
CHECK-CLEAN
REPLACE
CHECK
X
X
X
Cooling Fins
Spark Arrester
Fuel Tank
CLEAN
X
X
CLEAN
Fuel Filter
CHECK
X
Idle Speed
CHECK-ADJUST
CHECK-ADJUST
CHECK
X (2)
Valve Clearance
Fuel lines
X (2)
Every 2 years (replace if necessary) (2)
(1) Service more frequently when used in DUSTY areas.
(2) These items should be serviced by your service dealer, unless you have the proper tools and are mechanically
proficient. Refer to the HONDA Shop Manual for service procedures.
(3) For commercial use, log hours of operation to determine proper maintenance intervals.
PAGE 26 — GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ GA-2.5H — MAINTENANCE (ENGINE)
Cleaning the Fuel Strainer
Maintenance
Clean the fuel strainer if it contains dust or water. Remove
dust or water in the strainer cap and wash it in gasoline.
Securely fasten the fuel strainer cap so that fuel will not
leak. Check the fuel strainer every 200 hours of operation
or once a month.
Perform the scheduled maintenance procedures as defined
by Table 6 and below:
DAILY
■
Thoroughly remove dirt and oil from the engine and control
area. Clean or replace the air cleaner elements as
necessary.Check and retighten all fasteners as necessary.
Check the gearbox for oil leaks. Repair or replace as
needed.
DANGER
DO NOT use gasoline as a cleaning solvent,
because that would create a risk of fire or
explosion.
WEEKLY
■
Remove the fuel filter cap and clean the inside of the fuel
tank.
ENGINE AIR CLEANER
■
■
Remove or clean the filter at the bottom of the tank.
1. Remove the air cleaner cover and foam filter element as
shown in Figure 21.
Remove and clean the spark plug (Figure 19), then adjust
the spark gap to 0.024 ~0.028 inch (0.6~0.7 mm). This
unit has electronic ignition, which requires no adjustments.
2. Tap the paper filter element (Figure 21) several times on a
hard surface to remove dirt, or blow compressed air [not
exceeding 30 psi (207 kPa, 2.1 kgf/cm2)] through the filter
element from the air cleaner case side. NEVER brush off
dirt. Brushing will force dirt into the fibers. Replace the
paper filter element if it is excessively dirty.
Figure 19. Spark Plug Gap
ENGINE OIL
1. Drain the engine oil when the oil is warm as shown in
Figure 20.
2. Remove the oil drain bolt and sealing washer and allow
the oil to drain into a suitable container.
3. Replace engine oil with recommended type oil as listed
in Table 5. For engine oil capacity, see Table 2 (engine
specifications). DO NOT overfill.
4. Install drain bolt with sealing washer and tighten se-
curely.
Figure 21. Engine Air Cleaner
Figure 20. Engine Oil (Draining)
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 27
Download from Www.Somanuals.com. All Manuals Search And Download.
GA-2.5H — WIRING DIAGRAM (S/N 5496762 AND BELOW)
Figure 22. Generator/Engine Wiring Diagram (S/N 5496762 and below)
PAGE 28 — GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
GA-2.5H — WIRING DIAGRAM (S/N 5496763 AND ABOVE)
Figure 23. Generator/Engine Wiring Diagram (S/N 5496763 and above)
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 29
Download from Www.Somanuals.com. All Manuals Search And Download.
GA-2.5H — TROUBLESHOOTING (ENGINE)
diagnosis based on the Engine Troubleshooting (Table 7)
information shown below and on the proceeding page. If
the problem cannot be remedied, please leave the unit just
as it is and consult our company's business office or service
plant.
Practically all breakdowns can be prevented by proper
handling and maintenance inspections, but in the event of a
breakdown, please take a remedial action following the
TABLE 7. ENGINE TROUBLESHOOTING
SYMPTOM
POSSIBLE PROBLEM
SOLUTION
Inspect carburetor to see if fuel
is reaching it?
Check fuel line
No Fuel?
Add Fuel
Water in fuel tank?
Fuel filter clogged?
Stuck carburetor?
Spark plug is red?
Flush or replace fuel tank.
Replace fuel filter
Check float mechanism.
Poor starting
Spark plug is fouled. Check tranistor ignition unit.
Insufficient compression, injected air leaking. Carburetor jets are
clogged (overflow).
Spark plug is blue-white?
No spark present at tip of spark
plug?
Tranistor ignition unit broken, high voltage cord cracked or broken.
Start/Stop switch broken. Replace spark plug if fouled.
No oil?
Add oil as required.
Oil pressure alarm lamp blinks
upon starting?
Check Automatic shutdown circuit "oil sensor".
Replace cylinder and piston and if necessary axel joint.
Tighten cylinder head connecting bolts.
Engine will not turn over?
Cylinder head connecting bolts
loose?
Cylinder head gasket damaged? Replace cylinder head gasket.
Insufficient power output "no
compression"
Malfunction of valve seat?
Spark plug is loose?
Worn piston rings?
Re-seat valves.
Replace spark plug.
Replace piston rings.
Malfunction in air-cleaner
system, air filter clogged?
Clean or replace air filter.
Air leaking in from interface
between carburetor and cylinder
head?
Tighten bolts between carburetor and cylinder head. Replace
cylinder head gasket.
Insufficient power output
"compression"
Clean or replace fuel filter.
Clean or replace carburetor.
Check carburetor float.
Malfunction in fuel system?
PAGE 30 — GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
GA-2.5H — TROUBLESHOOTING (ENGINE)
TABLE 7. ENGINE TROUBLESHOOTING (CONTINUED)
SYMPTOM
POSSIBLE PROBLEM
Malfunction in blower?
SOLUTION
Check or replace blower.
Insufficient power output
"compression" and overheats
Air in-take filter clogged?
Clean or replace air in-take filter.
Over accumulation of exhaust
products?
Clean and check valves.
Check muffler, replace if necessary.
Burns to much fuel
Wrong spark plug?
Replace spark plug with manufactures suggested type spark plug.
Replace lubricating oil with correct viscosity.
Replace rings
Lubricating oil is wrong
viscosity?
Exhaust color is continiously
"WHITE"
Worn rings?
Air cleanner clogged?
Clean or replace air cleaner.
Choke valve has not been set
to the correct position?
Adjust choke valve to the correct position.
Exhaust color is continiously
"BLACK"
Carburetor defective, seal on
carburetor broken?
Replace carburetor or seal.
Adjust carburetor.
Poor carburetor adjustment
"engine runs too rich?
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 31
Download from Www.Somanuals.com. All Manuals Search And Download.
GA-2.5H — TROUBLESHOOTING (GENERATOR)
diagnosis based on the Generator Troubleshooting (Table 8)
information shown below and on the preceding page. If the
problem cannot be remedied, please leave the unit just as it
is and consult our company's business office or service plant.
Practically all generator breakdowns can be prevented by
proper handling and maintenance inspections, but in the
event of a breakdown, please take a remedial action following
the
TABLE 8. GENERATOR TROUBLESHOOTING
SYMPTOM
Low voltage
POSSIBLE PROBLEM
Engine speed too low?
SOLUTION
Raise engine speed to rated RPM.
AC voltmeter not working?
Replace AC voltmeter.
Control box internal wiring
malfunction?
Check control box wiring.
Defective ignition coil?
Check red and green ignition wires. Replace ignition wires if
necessary.
Low voltage. Engine speed
normal 3650 RPM (unloaded),
2500 RPM (idle)
Rotor winding malfunction?
Stator winding malfunction?
Breaker malfunction?
Check or replace rotor.
Check or replace stator.
Check or replace CB1.
Voltage output too high.
Engine speed too high?
Lower engine speed to rated RPM.
Check control box wiring.
Voltage output too high. Engine
speed normal 3650 RPM
(unloaded), 2500 RPM (idle)
Control box internal wiring
malfunction
Circuit breaker will not turn on
"NO LOAD"
Defective circuit breaker?
Replace circuit breaker.
Overload?
Reduce load or replace breaker.
Check load circuit for short.
Check solenoid.
Circuit breaker will turn on
"LOADED" but trips immediately.
Load circuit is shorted?
Stuck solenoid?
Does not accelerate from low to
high "NO LOAD"
Does not accelerate from low to
high "LOAD ACTIVE
Control box interal wiring
defective?
Check control box wiring.
Defective rotor windings?
Defective solenoid?
Check or replace rotor.
Check or replace solenoid.
Does not decelerate no
"VOLTAGE OUTPUT".
Defective idle control device?
Defective solenoid?
Check or replace idle control device.
Check or replace idle control device.
Check control box wiring, replace any defective components.
Check or replace solenoid.
Control box wiring malfunction?
Defective solenoid?
Does not decelerate but has
"VOLTAGE OUTPUT".
Idle control device malfunction?
Check or replace idle control device.
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE PAGE
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 33
Download from Www.Somanuals.com. All Manuals Search And Download.
GA-2.5H — EXPLANATION OF CODE IN REMARKS COLUMN
The following section explains the different symbols and
QTY. Column
remarks used in the Parts section of this manual. Use the help
numbers found on the back page of the manual if there are any
questions.
Numbers Used - Item quantity can be indicated by a
number, a blank entry, or A/R.
A/R (As Required) is generally used for hoses or other parts
that are sold in bulk and cut to length.
The contents and part numbers listed in the parts section are
subject to change without notice. Multiquip does not
guarantee the availibility of the parts listed.
A blank entry generally indicates that the item is not sold
separately. Other entries will be clarified in the “Remarks”
Column.
REMARKS Column
Sample Parts List:
Some of the most common notes found in the “Remarks”
Column are listed below. Other additional notes needed to
describe the item can also be shown.
NO. PART NO. PART NAME
QTY. REMARKS
1
2
2
3
4
12345
BOLT ...................... 1 ......INCLUDES ITEMS W/
WASHER, 1/4 IN. .............NOT SOLD SEPARATELY
WASHER, 3/8 IN. ... 1 ......MQ-45T ONLY
HOSE ................... A/R ....MAKE LOCALLY
BEARING ............... 1 ......S/N2345B AND ABOVE
*
*
*
12347
12348
12349
Assembly/Kit - All items on the parts list with the same
unique symbol will be included when this item is purchased.
Indicated by:
“INCLUDES ITEMS W/(unique symbol)”
NO. Column
Unique Symbols - All items with same unique symbol
Serial Number Break - Used to list an effective serial
number range where a particular part is used.
( , #,
+
, %, or >) in the number column belong to the same
*
assembly or kit, which is indicated by a note in the “Remarks”
column.
Indicated by:
“S/N XXXXX AND BELOW”
“S/N XXXX AND ABOVE”
“S/N XXXXTO S/N XXX”
Duplicate Item Numbers - Duplicate numbers indicate
multiple part numbers are in effect for the same general
item, such as different size saw blade guards in use or a
part that has been updated on newer versions of the same
machine.
Specific Model Number Use - Indicates that the part is
used only with the specific model number or model number
variant listed. It can also be used to show a part is NOT
used on a specific model or model number variant.
When ordering a part that has more than one
item number listed, check the remarks column
for help in determining the proper part to order.
Indicated by:
“XXXXX ONLY”
“NOT USED ON XXXX”
“Make/Obtain Locally” - Indicates that the part can be
purchased at any hardware shop or made out of available
items. Examples include battery cables, shims, and certain
washers and nuts.
PART NO. Column
Numbers Used - Part numbers can be indicated by a
number, a blank entry, orTBD.
“Not Sold Separately” - Indicates that an item cannot be
purchased as a separate item and is either part of an
assembly/kit that can be purchased, or is not available for
sale through Multiquip.
TBD (To Be Determined) is generally used to show a part
that has not been assigned a formal part number at time of
publication.
A blank entry generally indicates that the item is not sold
separately or is not sold by Multiquip. Other entries will be
clarified in the “Remarks” Column.
PAGE 34 — GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
GA-2.5H — SUGGESTED SPARE PARTS
GA-2.5H 1 TO 5 UNITS WITH HONDA
GX160K1EMA2 ENGINE
1 to 5 Units
Qty.
P/N
Description
5 ............ 9807956846.......... SPARK PLUG
1 ............ 15510ZE1033 ....... OIL LEVEL SWITCH
1 ............ 15600ZE1003 ....... DIPSTICK
1 ............ 36100ZE1015 ....... STOP SWITCH
5 ............ 17211ZBZ000 ....... ELEMENT AIR
5 ............ 28462ZH8003 ....... ROPE, RECOIL STARTER
2 ............ 0601804887.......... CIRCUIT BREAKER
2 ............ 0601812597.......... RECEPTACLE ...................... S/N 5496762 AND BELOW
2 ............ 0601812598.......... RECEPTACLE ...................... S/N 5496763 AND ABOVE
2 ............ 0601823204.......... RECTIFIER
2 ............ 0810107103.......... FILTER FUEL (TANK) ........... S/N 5496762 AND BELOW
2 ............ A9924800004 ....... FILTER FUEL (TANK) ........... S/N 5496763 AND ABOVE
1 ............ 16950898632 ........ FUEL COCK
5 ............ 16952883005 ........ FUEL FILTER
1 ............ A9924800014 ....... CAP, FUEL TANK
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 35
Download from Www.Somanuals.com. All Manuals Search And Download.
GA-2.5H — NAMEPLATE AND DECALS.
Machine Safety Decals
The GA-2.5H portable generator is equipped with a number of safety decals (see below). These decals are provided for
operator safety and maintenance information. The illustration below shows these decals as they appear on the machine.
Should any of these decals become unreadable, replacements can be obtained from your dealer
PAGE 36 — GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
GA-2.5H — NAMEPLATE AND DECALS.
NAME PLATE ASSY.
NO.
1
1
2
3
PART NO.
PART NAME
QTY.
REMARKS
7930505002
A2511201002
87528ZB2630
1980680004
DECAL; CONTROL PANEL ..................................... 1 ............... S/N 5496762 AND BELOW
DECAL; CONTROL PANEL ..................................... 1 ............... S/N 5496763 AND ABOVE
DECAL; CHOKE ...................................................... 1 ............... S/N 5496763 AND ABOVE
DECAL; FUEL COCK .............................................. 1 ............... S-3704
4
5
6
6
7
8
9
10
10
11
12
13
14
NAMEPLATE ............................................................ 1 ............... CONTACT MQ PARTS
87533ZC0630
7980615403
A2561000003
8700611804
8700611904
0800628504
7900638204
A9521200004
7900636004
0820610404
35137
DECAL; AIR CLEANER
1
DECAL; MQ MULTIQUIP 2500 ................................ 1 ............... S/N 5496762 AND BELOW
DECAL; MQ MULTIQUIP 2500 ................................ 1 ............... S/N 5496763 AND ABOVE
DECAL; WARNING DANGEROUS GAS ................. 1 ............... S-4984
DECAL; DANGER ELECTRICAL SHOCK HAZ....... 1 ............... S-4985
DECAL: GROUND .................................................... 1 ............... S-1123
DECAL; OPERATING INSTRUCTIONS, S-4607 ..... 1 ............... S/N 5496762 AND BELOW
DECAL; OPERATING INSTRUCTIONS .................. 1 ............... S/N 5496763 AND ABOVE
DECAL; CAUTION OPER. AT 3600 RPM ONLY ..... 1 ............... S-4461
DECAL; WARNING, TRANSFER SWITCH.............. 1 ............... S-3627
DECAL; WARNING, READ MANUAL ...................... 1 ............... S/N 5496763 AND ABOVE
DECAL; WARNING, READ MANUAL, DSC01......... 1 ............... S/N 5496762 AND BELOW
0820610804
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 37
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ GA-2.5H — GENERATOR ASSY .
GENERATOR ASSY.
PAGE 38 — GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ GA-2.5H — GENERATOR ASSY .
GENERATOR ASSY.
NO
1
PART NO
PART NAME
QTY.
REMARKS
7931000203
ROTOR ASSY. ............................... 1 ............. INCLUDES ITEMS W/
*
1-1
FIELD COIL ASSY. ......................... 1 ............. NOT SOLD SEPERATELY
RECTIFIER ..................................... 2 ............. D3SB 80
SURGE ABSORBER ...................... 2 ............. TNR 15G431K
BEARING ........................................ 1 ............. 6204 2RU NY5C S30
SET BOLT, ROTOR
SET WASHER, BEARING
SPRING WASHER
ARMATURE ASSY. ......................... 1 ............. S/N 5497956 AND BELOW
ARMATURE ASSY. ......................... 1 ............. S/N 5497957 AND ABOVE
END BRACKET (C SIDE)
END BRACKET (B SIDE)
GUIDE PANEL, AIR
COVER
SET BOLT, STATOR
SPRING WASHER
PLAIN WASHER
GROMMET
*
1-2
1-2
1-3
2
0601823213
0601822638
0603000040
7681017104
0801086004
0040008000
7921341803
A2135000203
7931315002
7931315102
7875021523
7681331003
7681344204
0040006000
0041206000
7871329514
0601851760
0013608025
0013608020
0040008000
7935420104
0017106016
7935420004
0207206000
0017108020
*
1
1
1
3
4
5
5
6
7
8
9
10
11
12
13
14
15
15
15A
16
17
1
1
1
1
4
4
4
1
1
CAP
HEX. HEAD BOLT ........................... 4 ............. S/N 5497956 AND BELOW
HEX. HEAD BOLT ........................... 4 ............. S/N 5497957 AND ABOVE
SPRING WASHER
MUFFLER STAY ............................. 1 ............. S/N 5497957 AND ABOVE
HEX. HEAD BOLT ........................... 2 ............. S/N 5497957 AND ABOVE
MUFFLER STAY.............................. 1 ............. S/N 5497957 AND ABOVE
4
18
19
20
HEX NUT
HEX HEAD BOLT
2
1
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 39
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ GA-2.5H — CONTROL BOX ASSY. S/N 5496762 AND BELOW
CONTROL BOX ASSY. (S/N 5496762 AND BELOW)
PAGE 40 — GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ GA-2.5H — CONTROL BOX ASSY. S/N 5496762 AND BELOW
CONTROL BOX ASSY. (S/N 5496762 AND BELOW)
NO.
1
2
3
4
5
6
7
8
PART NO.
PART NAME
CONTROL BOX
GROMMET
QTY.
1
1
REMARKS
7931800203
0801354504
0601823204
0027103020
011106015
7931810303
0601800258
0038303000
0601804887
3011816004
0027104010
0601812597
0027104010
0038404000
0601815103
0017105010
RECTIFIER ..........................................1........... S5 VB60
MACHINE SCREW
HEX. HEAD BOLT ................................4........... REPLACES 0017106015
CONTROL PANEL
AC VOLTMETER .................................. 1........... 120/ 240V 8283
HEX. NUT
CIRCUIT BREAKER.............................1........... KM- 51 265V 20A
BRACKET, CIRCUIT BREAKER
MACHINE SCREW
RECEPTACLE ......................................1........... 5- 20R GF- 5352(G.F.C.I.)
MACHINE SCREW
HEX. NUT............................................. 2........... OEMAA8
1
1
2
9
10
11
12
13
13A
14
15
1
2
2
GROUND TERMINAL
HEX. HEAD BOLT
1
4
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 41
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ GA-2.5H — CONTROL BOX ASSY. S/N 5496763 AND ABOVE
CONTROL BOX ASSY. (S/N 5496763 AND ABOVE)
PAGE 42 — GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ GA-2.5H — CONTROL BOX ASSY. S/N 5496763 AND ABOVE
CONTROL BOX ASSY. (S/N 5496763 AND ABOVE)
NO
1
2
3
4
5
6
7
8
PART NO
PART NAME
CONTROL BOX
GROMMET
RECTIFIER ............................................... 1 ................. S5VB60
MACHINE SCREW
CONTROL PANEL
CIRCUIT BREAKER ................................. 1 ................. KM-51 : 20A
BRACKET, CIRCUIT BREAKER
MACHINE SCREW
AC VOLTMETER ...................................... 1 ................. DE450-011 : 0 ~ 120V
RECEPTACLE........................................... 1 ................. 5-20R: 125V, 20A
RECEPTACLE........................................... 1 ................. L5-20R:125V, 20A
MACHINE SCREW
HEX NUT
QTY.
1
1
REMARKS
A0101000103
0801354504
0601823204
0027103012
A2224000103
0601804887
3011816004
0021004010
0601806819
0601812598
0601812592
0021004010
0207004000
0021004015
0207004000
0017106016
0017105010
1
1
1
2
9
10
11
12
12A
13
13A
14
15
4
4
4
1
4
4
MACHINE SCREW
HEX NUT
HEX. HEAD BOLT
HEX. HEAD BOLT
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 43
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ GA-2.5H — PIPE FRAME ASSY. S/N 5496762 AND BELOW
PIPE FRAME ASSY. (S/N 5496762 AND BELOW)
PAGE 44 — GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ GA-2.5H — PIPE FRAME ASSY. S/N 5496762 AND BELOW
PIPE FRAME ASSY. (S/N 5496762 AND BELOW)
NO.
1
2
3
4
5
6
7
8
PART NO.
PART NAME
QTY.
REMARKS
7935400302
0801886104
7935419204
7935419304
020108060
7935510102
0810106004
0810107103
0602125031
16950898632
PIPE FRAME
1
2
2
2
WASHER
RUBBER SUSPENSION
RUBBER SUSPENSION
HEX. NUT............................................. 8........... REPLACES 0207208000
FUEL TANK
CAP, FUEL TANK
FUEL FILTER
FUEL GAUGE ......................................1........... CJ-13
FUEL COCK
CUP
FILTER
1
1
1
9
10
1
1
1
1
2
1
2
2
10- 1 16081471831
10- 2 16952883005
11
12
13
14
15
16
17
18
19
20
21
21A
22
23
24
950014500160M HOSE
9500202080
90854ZB2000
7855525514
7855525604
011208030
011008020
7935421004
0017106016
0017106016
0017106016
0040506000
020108060
011208025
0040008000
HOSE BAND
GROMMET
RUBBER WASHER
COLLAR
HEX. HEAD BOLT ................................2........... REPLACES 0017108030
HEX. HEAD BOLT ................................2........... REPLACES 0017108020
BRACKET, MUFFLER COVER
HEX. HEAD BOLT
HEX. HEAD BOLT
HEX. HEAD BAOLT
TOOTH WASHER
HEX. NUT
1
2
3
1
1
2
REPLACES 0031308000
HEX. HEAD BOLT ................................2........... REPLACES 0011308025
SPRING WASHER
2
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 45
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ GA-2.5H — PIPE FRAME ASSY. S/N 5496763 AND ABOVE
PIPE FRAME ASSY. (S/N 5496763 AND ABOVE)
PAGE 46 — GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ GA-2.5H — PIPE FRAME ASSY. S/N 5496763 AND ABOVE
PIPE FRAME ASSY. (S/N 5496763 AND ABOVE)
NO.
1
2
3
4
PART NO.
PART NAME
QTY.
1
2
REMARKS
A2417000202
7935419204
020108060
PIPE FRAME
RUBBER SUSPENSION
HEX. NUT............................................................ 4 ........ REPLACES 0207208000
RUBBER SUSPENSION ..................................... 2
7935419304
020108060
5
HEX. NUT............................................................ 4 ........ REPLACES 0207208000
6
7
8
9
A2364000002
A9924800014
A9924800004
0602125034
16950898632
FUEL TANK
CAP, FUEL TANK
FUEL FILTER
FUEL GAUGE ..................................................... 1 ........ CJ-58A
FUEL COCK
CUP, FUEL STRAINER
FILTER N/C
1
1
1
10
1
1
1
1
2
2
2
10- 1 16081471831
10- 2 16952883005
11
12
13
14
15
16
17
18
19
20
21
22
23
950014518040 HOSE
9500202080
7855525514
7855525604
011208030
011008020
7935421004
0017106016
0017106016
0019206016
0011308020
0040008000
020108060
HOSE BAND
RUBBER CUSHION
COLLAR
HEX. HEAD BOLT ............................................... 2 ........ REPLACES 0017108030
HEX. HEAD BOLT ............................................... 2 ........ REPLACES 0017108020
BRACKET, MUFFLER COVER
HEX. HEAD BOLT
HEX. HEAD BOLT
HEX. HEAD BOLT
1
2
3
1
2
2
HEX. HEAD BOLT
WASHER, LOCK
HEX. NUT............................................................ 2 ........ REPLACES 0031308000
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 47
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1EMA2 ENGINE — CYLINDER HEAD ASSY.
CYLINDER HEAD ASSY.
PAGE 48 — GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1EMA2 ENGINE — CYLINDER HEAD ASSY.
CYLINDER HEAD ASSY.
NO
PART NO
PART NAME
QTY.
REMARKS
1
12210ZH8020
12204ZE1306
12205ZE1315
12216ZE5300
12251ZF1800
12310ZE1010
12391ZE1000
15721732000
90013883000
90043ZB2003
90047ZE1000
9430110160
957230806000
9807956846
9807956855
HEAD COMP., CYLINDER ........................ 1 .........INCLUDES ITEMS W/
*
2
*
3
*
4
*
5
6
7
GUIDE, IN. VALVE (OVER SIZE)
GUIDE, IN. VALVE
CLIP, VALVE GUIDE
GASKET, CYLINDER HEAD
COVER COMP, HEAD
PACKING, HEAD COVER
TUBE, BREATHER
BOLT, FLANGE 6X12
BOLT, STUD 6X94
BOLT, STUD 8X32
PIN, DOWEL 10X1
BOLT, FLANGE 8X60
PLUG, SPARK (BPR6ES NGK)
PLUB, SPARK (W20EPR-U ND)
1
1
1
1
1
1
1
4
2
2
2
4
1
1
8
9
10
11
12
13
14
14
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 49
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1EMA2 ENGINE — CYLINDER BARREL ASSY.
CYLINDER BARREL ASSY.
PAGE 50 — GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1EMA2 ENGINE — CYLINDER BARREL ASSY.
CYLINDER BARREL ASSY.
NO
2
3
PART NO
PART NAME
BARREL ASSY, CYLINDER ................................1......... INCLUDES ITEMS W/
SWITCH ASSY, OIL LEVEL
QTY.
REMARKS
12000ZH8406
15510ZE1033
16510ZE1000
#
1
4
GOVERNOR ASSY. .............................................1......... USE UP TO S/N 4913229
......................................................................................... INCLUDES ITEMS W/
GOVERNOR ASSY. ............................................. 1......... USE FROM S/N 4913230
*
4
16506ZL0000
......................................................................................... INCLUDES ITEMS W/
*
5
*
6
*
7
*
8
16511ZE1000
16512ZE1000
16513ZE1000
16531ZE1000
16541ZE1000
90131ZE1000
90451ZE1000
90601ZE1000
90602ZE1000
91001ZF1003
91201Z0T801
91353671004
9405010000
WEIGHT, GOVERNOR
HOLDER, GOVENOR WEIGHT
PIN, GOVERNOR WEIGHT
SLIDER, GOVERNOR
SHAFT, GOVERNOR ARM
BOLT, DRAIN PLUG
2
1
2
1
1
2
1
2
1
1
1
1
1
2
1
2
1
9
12
13
14
15
16
17
18
19
20
21
22
23
WASHER, THRUST 6MM
WASHER, DRAIN PLUG 10.2MM
CLIP, GOVERNOR HOLDER
BEARING, RADIAL BALL(6205TMB)
OIL SEAL 25X41X6
#
#
O-RING, 13.5X1.5
NUT, FLANGE, 10MM
9410106800
9425108000
957010601200
06111ZH8405
WASHER, PLAIN, 6MM
PIN, LOCK, 8MM
BOLT, FLANGE, 6X12
GASKET KIT
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 51
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1EMA2 ENGINE — CRANKCASE COVER ASSY.
CRANKCASE COVER ASSY.
PAGE 52 — GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1EMA2 ENGINE — CRANKCASE COVER ASSY.
CRANKCASE COVER ASSY.
NO
1
3
PART NO
PART NAME
QTY.
REMARKS
11300ZE1634
11381ZH8801
15600ZE1003
15600ZG4003
15625ZE1003
91201Z0T801
9430108140
957010803200
961006205000
COVER ASSY, CRANKCASE ............................. 1 ............ INCLUDES ITEMS W/
*
#
GASKET, CASE COVER
CAP ASSY, OIL FILLER ...................................... 1 ............ INCLUDES ITEMS W/
CAP, OIL FILLER
GASKET, OIL FILLER CAP
OIL SEAL, 25X41X6
PIN, DOWEL 8X14
BOLT, LANGE 8X32
BEARING, RADIAL BALL, 6205
1
4
5
1
1
1
2
6
1
8
9
#
*
10
11
12
*
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 53
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1EMA2 ENGINE — CRANKSHAFT ASSY.
CRANKSHAFT ASSY.
PAGE 54 — GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1EMA2 ENGINE — CRANKSHAFT ASSY.
CRANKSHAFT ASSY.
NO
1
PART NO
13310ZB2000
PART NAME
CRANKSHAFT (VE-TYPE)
QTY. REMARKS
1
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 55
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1EMA2 ENGINE — PISTON ASSY.
PISTON ASSY.
PAGE 56 — GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1EMA2 ENGINE — PISTON ASSY.
PISTON ASSY.
NO
1
1
1
1
2
2
2
2
3
4
5
6
PART NO
PART NAME
QTY.
REMARKS
13010ZF1023
13011ZF1023
13012ZF1023
13013ZF1023
13101ZH8010
13101ZH8010
13103ZH8000
13102ZH8010
13111ZE1000
132000ZE1010
90001ZE1000
90551ZE1000
RING SET, PISTON (STD)
RING SET, PISTON (0.25)
RING SET, PISTON (0.50)
RING SET, PISTON (0.75)
PISTON (STD)
1
1
1
1
1
1
1
1
1
1
2
2
PISTON (0.25)
PISTON (0.50)
PISTON (0.75)
PIN, PISTON
ROD ASSY, CONNECTING
BOLT, CONNECTING ROD
CLIP, PISTON PIN, 18MM
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 57
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1EMA2 ENGINE — CAMSHAFT ASSY.
CAMSHAFT ASSY.
PAGE 58 — GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1EMA2 ENGINE — CAMSHAFT ASSY.
CAMSHAFT ASSY.
NO
1
1
2
3
4
5
6
7
PART NO
PART NAME
QTY.
REMARKS
14100ZE1812
14100ZL0000
14410ZE1010
14431ZE1000
14441ZE1000
14451ZE1013
14568ZE1000
14711ZF1000
14721ZF1000
14751ZF1000
14771ZE1000
14773ZE1000
14781ZE1000
14791ZE1010
90012ZE0010
90206ZE1000
12209ZH8003
CAM SHAFT ASSY.............................................. 1 ............ UP TO S/N 4913229
CAM SHAFT ASSY.............................................. 1 ............ FROM S/N 4913230
ROD, PUSH
ARM, VALVE ROCKER
LIFTER, VALVE
PIVOT, ROCKER ARM
SPRING, WEIGHT RETURN
VALVE, IN
2
2
2
2
1
1
1
2
1
1
1
1
2
2
1
8
9
VALVE, EX
SPRING, VALVE
10
11
12
13
14
15
18
RETAINER, IN. VALVE SPRING
RETAINER, EX. VALVE SPRING
ROTATOR, VALVE
PLATE, PUSH ROD GUIDE
BOLT, PIVOT (8MM)
NUT, PIVOT ADJUSTING
VALVE STEM
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 59
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1EMA2 ENGINE — RECOIL STARTER ASSY.
RECOIL STARTER ASSY.
PAGE 60 — GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1EMA2 ENGINE — RECOIL STARTER ASSY.
RECOIL STARTER ASSY.
NO
1
2
3
4
5
6
7
8
PART NO
PART NAME
QTY. REMARKS
28400ZH8013ZB
28410ZH8003ZB
28420ZH8013
28422ZH8013
28433ZH8003
28441ZH8003
28442ZH8003
28443ZH8003
28461ZH8003
28462ZH8003
90003ZH8003
90008ZE2003
STARTER ASSY, RECOIL “NH1” BLACK
CASE, RECOIL STARTER “NH1” BLACK
REEL, RECOIL STARTER
RATCHET, STARTER
1
1
1
2
1
1
1
2
1
1
1
3
GUIDE, RATCHET
SPRING, FRICTION
SPRING, RECOIL STARTER
SPRING, RETURN
KNOB, RECOIL STARTER
ROPE, RECOIL STARTER
SCREW, SETTING
9
10
12
13
BOLT, FLANGE 6X10
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 61
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1EMA2 ENGINE — FAN COVER ASSY.
FAN COVER ASSY.
PAGE 62 — GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1EMA2 ENGINE — FAN COVER ASSY.
FAN COVER ASSY.
NO
PART NO
PART NAME
SPRING, CONTROL ADJUSTING
COVER, FAN “NH1” BLACK
PLATE, SIDE ALERT & LAMP ............ 1 ............... USE FROM S/N 475372719
PLATE, SIDE LAMP ............................ 1 ............... USE FROM S/N 4795906~5372718
PLATE, SIDE ALERT & LAMP ............ 1 ............... USE UP TO S/N 4795905
CLAMP, CORD .................................... 1 ............... USE UP TO S/N 4367320
CLAMP, CORD .................................... 1 ............... USE FROM S/N 4367321
QTY.
1
1
REMARKS
3
*
4
7
7
7
10
10
11
12
16584883300
19610ZE1000ZC
19611ZH8820
19612ZH8821
19612ZH8830
19613ZE1010
90601ZH7013
19630ZB2000
19640ZB2010
SHROUD COMP., LOWER
SHROUD ASSY., UPPER ................... 1 ............... USE UP TO S/N 5048024
1
` .............................................................................. INCLUDES ITEMS W/
SHROUD ASSY., UPPER ................... 1 ............... USE FROM S/N 5048025
*
12
19640ZH8R60
............................................................................... INCLUDES ITEMS W/
SUB HARNESS................................... 1 ............... USE UP TO S/N 4367320
ENGINE, STOP SWITCH .................... 1 ............... USE UP TO S/N 4368640
ENGINE, STOP SWITCH .................... 1 ............... USE FROM S/N 4368641
*
13
14
14
17
18
19
32197ZH8003
36100ZE1015
36100ZH7003
90013883000
90022888010
93500050350A
93500050400G
957010600800
34150ZH7003
957010600800
BOLT, FANGE 6X12
BOLT, FLANGE 6X20
8
1
SCREW, PAN 5X35 ............................. 1 ............... USE UP TO S/N 5048024
SCREW, PAN 5X40 ............................. 1 ............... USE FROM S/N 5048025
*
19
21
23
24
*
BOLT, FLANGE 6X8
1
ALERT UNIT, OIL ................................ 1 ............... USE FROM S/N 5372719
BOLT, FLANGE 6X8 ............................ 1 ............... USE FROM S/N 5372719
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 63
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1EMA2 ENGINE — CARBURETOR ASSY.
CARBURETOR ASSY.
PAGE 64 — GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1EMA2 ENGINE — CARBURETOR ASSY.
CARBURETOR ASSY.
NO
PART NO
PART NAME
QTY.
REMARKS
1
2
3
4
4
6
7
8
9
10
11
12
13
14
15
16
17
#%
+
16010ZB1015
16011ZE0005
16013ZE0005
16015ZE0831
16015ZE1811
16016ZH7W01
16024ZE1811
16028ZE0005
16044ZE0005
16100ZH8E81
16124ZE0005
16166ZH8E80
16211ZE1000
16212ZH8800
16221ZH8801
16269ZE1800
16610ZB2000
9430520122
GASKET SET
VALVE SET, FLOAT
FLOAT SET
1
1
1
*
*
*
*
*
CHAMBER SET, FLOAT ................................1 .......... USE FROM S/N BE67A A
CHAMBER SET, FLOAT ................................1 .......... USE FROM S/N BE51A A
SCREW SET
SCREW SET, DRAIN.....................................1 .......... INCLUDES ITEMS W/
SCREW SET, B .............................................1 .......... INCLUDES ITEMS W/+
CHOKE SET
CARBURETOR ASSY,(BE67A B) ..................1 .......... INCLUDES ITEMS W/
SCREW, THROTTLE STOP
NOZZLE, MAIN
INSULATOR, CARBURETOR
GASKET, INSULATOR
GASKET, CARBURETOR
GASKET, AIR CLEANER
1
%
1
*
*
1
1
1
1
1
1
*
*
LEVER COMP., CHOKE ................................1 .......... INCLUDES ITEMS W/ <
PIN, SPRING 2X12
JET, MAIN, #70, OPTION
JET, MAIN, #72, OPTION
JET, MAIN, #75,
18 <
19
19
1
1
1
1
99101ZH80700
99101ZH80720
99101ZH80750
99204ZE00350
19
20
*
*
JET SET, PILOT, #35 .....................................1 .......... INCLUDES ITEMS W/#
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 65
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1EMA2 ENGINE — AIR CLEANER ASSY.
AIR CLEANER ASSY.
PAGE 66 — GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1EMA2 ENGINE — AIR CLEANER ASSY.
AIR CLEANER ASSY.
NO
1
2
3
4
5
6
7
8
PART NO
PART NAME
QTY.
REMARKS
17211ZB2000
17212ZB2000
17220ZB2000
17231ZB2000
17239ZB2000
17252ZB2000
90115459770
9405006080
957010601000
ELEMENT, AIR CLEANER
SEPARATOR, AIR CLEANER
CASE COMP., AIR CLEANER
COVER AIR CLEANER
STAY AIR CLEANER
SEAL, AIR CLEANER
BOLT, SETTING
1
1
1
1
1
1
4
2
1
BOLT, FLANGE, 6MM
BOLT, FLANGE, 6X10
9
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 67
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1EMA2 ENGINE — MUFFLER ASSY.
MUFFLER ASSY.
PAGE 68 — GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1EMA2 ENGINE — MUFFLER ASSY.
MUFFLER ASSY.
NO
1
2
3
4
5
6
8
9
PART NO
PART NAME
QTY.
REMARKS
18310ZB3C00
18320ZB2000
18325ZH8T90
18329ZB2000
18330ZH8T90
18355898630
18381ZE1800
18381ZH8800
MUFFLER COMP.
1
1
1
2
1
1
1
1
PROTECTOR, MUFFLER OUTER
PROTECTOR, MUFFLER INNER
SEAL, MUFFLER PROTECTOR
PIPE COMP., EX
ARRESTER, SPARK
GASKET, MUFFLER
GASKET, MUFFLER
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 69
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1EMA2 ENGINE — FLYWHEEL ASSY.
PAGE 70 — GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1EMA2 ENGINE — FLYWHEEL ASSY.
FLYWHEEL ASSY.
NO
1
2
3
4
PART NO
PART NAME
KEY, SPECIAL WOOD RUFF, 25X18
FAN, COOLING
PULLEY, STARTER
FLYWHEEL (LAMP)
NUT, SPECIAL, 14MM
QTY.
REMARKS
13331357000
19511ZE1000
28451ZH8003
31100ZE1811
90201878003
1
1
1
1
1
5
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 71
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1EMA2 ENGINE — IGNITION COIL ASSY.
IGNITION COIL ASSY.
PAGE 72 — GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1EMA2 ENGINE — IGNITION COIL ASSY.
IGNITION COIL ASSY.
NO
1
2
4
6
PART NO
PART NAME
QTY. REMARKS
30500ZE1043
30700ZE1013
31510ZE1811
31511ZE1000
31512ZE1000
90015883000
90019883000
90121952000
36101ZE1010
COIL ASSY., IGNITION
CAP ASSY., NOISE SUPPRESSOR
COIL ASSY., LAMP (12V25W)
CLAMP, WIRE
1
1
1
1
1
2
1
2
7
GROMMET, WIRE
12
13
14
15
BOLT, FLANGE, 6X28
BOLT, FLANGE, 5X10
BOLT, FLANGE, 6X25
WIRE, STOP SWITCH
`
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 73
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1EMA2 ENGINE — GOVERNOR/CONTROL ASSY.
GOVERNOR/CONTROL ASSY.
PAGE 74 — GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1EMA2 ENGINE — GOVERNOR/CONTROL ASSY.
GOVERNOR/CONTROL ASSY.
NO
1
1
2
3
3
3
4
5
PART NO
PART NAME
QTY.
REMARKS
16551ZE0010
16551ZL0010
16555ZE1000
16561ZH8D00
16561ZL0U30
16561ZL0000
16562ZE1020
90015ZE5010
9405006000
ARM, GOVERNOR.................................... 1 ......... USE UP TO S/N 4913229
ARM, GOVERNOR.................................... 1 ......... USE FROM S/N 4913230
ROD, GOVERNOR
1
SPRING, GOVERNOR .............................. 1 ......... USE UP TO S/N 4913229
SPRING, GOVERNOR .............................. 1 ......... USE FROM S/N 4913230~5048024
SPRING, GOVERNOR .............................. 1 ......... USE FROM S/N 5048025
SPRING, THROTTLE RETURN
BOLT, GOVERNOR ARM
NUT, FLANGE, 6MM
1
1
1
6
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 75
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1EMA2 ENGINE — LABELS ASSY.
PAGE 76 — GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1EMA2 ENGINE — LABELS ASSY.
IGNITION COIL ASSY.
NO
1
12
21
PART NO
PART NAME
QTY.
REMARKS
87521ZH8020
87528ZB2630
87533ZC0630
EMBLEM, 5.5 HP
DECAL, CHOKE
DECAL, AIR CLEANER
1
1
1
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 77
Download from Www.Somanuals.com. All Manuals Search And Download.
TERMS AND CONDITIONS OF SALE — PARTS
PAYMENT TERMS
5. Partsmustbeinnewandresalablecon- Multiquipreservestherighttoquoteandsell
dition,intheoriginalMultiquippackage(if directtoGovernmentagencies,andtoOriginal
any), and with Multiquip part numbers Equipment Manufacturer accounts who use
Terms of payment for parts are net 30 days.
FREIGHTPOLICY
clearlymarked.
our products as integral parts of their own
products.
All parts orders will be shipped collect or
prepaidwiththechargesaddedtotheinvoice.
All shipments are F.O.B. point of origin.
Multiquip’sresponsibilityceaseswhenasigned
manifesthasbeenobtainedfromthecarrier,
andanyclaimforshortageordamagemustbe
settledbetweentheconsigneeandthecarrier.
6. Thefollowingitemsarenotreturnable:
SPECIALEXPEDITINGSERVICE
a. Obsolete parts. (If an item is in the
price book and shows as being re- A$35.00surchargewillbeaddedtotheinvoice
placedbyanotheritem,itisobsolete.) forspecialhandlingincludingbusshipments,
insuredparcelpostorincaseswhereMultiquip
mustpersonallydeliverthepartstothecarrier.
(such as gaskets, seals, “O” rings,
b. Any parts with a limited shelf life
andotherrubberparts)thatwerepur- LIMITATIONSOFSELLER’SLIABILITY
MINIMUMORDER
chasedmorethansixmonthspriorto
thereturndate.
Multiquip shall not be liable hereunder for
damagesinexcessofthepurchasepriceofthe
TheminimumchargeforordersfromMultiquip
is $15.00 net. Customers will be asked for
instructionsregardinghandlingofordersnot
meetingthisrequirement.
c. Anylineitemwithanextendeddealer item with respect to which damages are
netpriceoflessthan$5.00.
claimed, and in no event shall Multiquip be
liable for loss of profit or good will or for any
otherspecial,consequentialorincidentaldam-
ages.
d. Special order items.
RETURNEDGOODSPOLICY
e. Electricalcomponents.
f. Paint,chemicals,andlubricants.
g. Decalsandpaperproducts.
h. Itemspurchasedinkits.
Returnshipmentswillbeacceptedandcredit
willbeallowed,subjecttothefollowingprovi-
sions:
LIMITATIONOFWARRANTIES
Nowarranties,expressorimplied,aremade
in connection with the sale of parts or trade
accessoriesnorastoanyenginenotmanufac-
tured by Multiquip. Such warranties made in
connectionwiththesaleofnew,completeunits
are made exclusively by a statement of war-
rantypackagedwithsuchunits,andMultiquip
neitherassumesnorauthorizesanypersonto
assume for it any other obligation or liability
whatever in connection with the sale of its
products.Apartfromsuchwrittenstatementof
warranty, there are no warranties, express,
impliedorstatutory,whichextendbeyondthe
descriptionoftheproductsonthefacehereof.
1. AReturnedMaterialAuthorizationmust
be approved by Multiquip prior to ship-
ment.
7. Thesenderwillbenotifiedofanymaterial
receivedthatisnotacceptable.
2. ToobtainaReturnMaterialAuthorization,
alistmustbeprovidedtoMultiquipParts
Salesthatdefinesitemnumbers,quanti-
ties, and descriptions of the items to be
returned.
8. Suchmaterialwillbeheldforfiveworking
days from notification, pending instruc-
tions.Ifareplyisnotreceivedwithinfive
days,thematerialwillbereturnedtothe
senderathisexpense.
a. Thepartsnumbersanddescriptions
must match the current parts price
list.
9. Creditonreturnedpartswillbeissuedat
dealer net price at time of the original
purchase,lessa15%restockingcharge.
b. The list must be typed or computer
generated.
10. In cases where an item is accepted, for
which the original purchase document
can not be determined, the price will be
basedonthelistpricethatwaseffective
twelvemonthspriortotheRMAdate.
c. The list must state the reason(s) for
thereturn.
Effective: February 22, 2006
d. The list must reference the sales
order(s)orinvoice(s)underwhichthe
itemswereoriginallypurchased.
11. Credit issued will be applied to future
purchasesonly.
e. The list must include the name and
phonenumberofthepersonrequest-
ingtheRMA.
PRICINGANDREBATES
Prices are subject to change without prior
notice.Pricechangesareeffectiveonaspe-
cificdateandallordersreceivedonorafterthat
datewillbebilledattherevisedprice.Rebates
3. AcopyoftheReturnMaterialAuthoriza-
tionmustaccompanythereturnshipment.
4. Freight is at the sender’s expense. All forpricedeclinesandaddedchargesforprice
partsmustbereturnedfreightprepaidto increaseswillnotbemadeforstockonhand
Multiquip’sdesignatedreceivingpoint.
atthetimeofanypricechange.
PAGE 78 — GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE PAGE
GA-2.5H A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #5 (03/04/08) — PAGE 79
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION AND PARTS MANUAL
HERE’S HOW TO GET HELP
PLEASE HAVETHE MODEL AND SERIAL
NUMBER ON-HANDWHEN CALLING
UNITED STATES
Multiquip Corporate Office
18910 Wilmington Ave.
Carson, CA 90746
MQ Parts Department
800-427-1244
Tel. (800) 421-1244
Fax (800) 537-3927
Fax: 800-672-7877
Fax: 310-637-3284
310-537-3700
Contact: [email protected]
Mayco Parts
800-306-2926
310-537-3700
Warranty Department
800-421-1244, Ext. 279 Fax: 310-537-1173
310-537-3700, Ext. 279
Fax: 800-672-7877
Fax: 310-637-3284
Service Department
800-421-1244
Technical Assistance
800-478-1244
Fax: 310-537-4259
Fax: 310-631-5032
310-537-3700
MEXICO
MQ Cipsa
Carr. Fed. Mexico-Puebla KM 126.5
Momoxpan, Cholula, Puebla 72760 Mexico Fax: (52) 222-285-0420
Contact: [email protected]
UNITED KINGDOM
Multiquip (UK) Limited Head Office
Hanover Mill, Fitzroy Street,
Ashton-under-Lyne,
Tel: (52) 222-225-9900
Tel: 0161 339 2223
Fax: 0161 339 3226
Lancashire OL7 0TL
Contact: [email protected]
CANADA
Multiquip
4110 Industriel Boul.
Laval, Quebec, Canada H7L 6V3
Contact: [email protected]
BRAZIL
Multiquip
Tel: (450) 625-2244
Fax: (450) 625-8664
Av. Evandro Lins e Silva, 840 - grupo 505 Tel: 011-55-21-3433-9055
Barra de Tijuca - Rio de Janeiro Fax: 011-55-21-3433-9055
Contact: [email protected], [email protected]
© COPYRIGHT 2008, MULTIQUIP INC.
Multiquip Inc, the MQ logo are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without written permission. All other trademarks are the
property of their respective owners and used with permission.
This manual MUST accompany the equipment at all times. This manual is considered a permanent part of the equipment and should remain with the unit if resold.
The information and specifications included in this publication were in effect at the time of approval for printing. Illustrations, descriptions, references and technical data
contained in this manual are for guidance only and may not be considered as binding. Multiquip Inc. reserves the right to discontinue or change specifications, design or
the information published in this publication at any time without notice and without incurring any obligations.
Your Local Dealer is:
Download from Www.Somanuals.com. All Manuals Search And Download.
|