OPERATION & PARTS MANUAL
MODEL QP-40TE
TRASH PUMP
(ROBIN GASOLINE ENGINE)
Revision #0 (04/13/05)
To find the latest revision of this
publication, visit our website at:
THIS MANUAL MUST ACCOMPANYTHE EQUIPMENT AT ALLTIMES.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES PAGE
QP- 40TE — OPERATION & PARTS MANUAL — REV. #0 (04/13/05) — PAGE 3
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
Multiquip QP-40TE Trash
Pump
ROBIN EX270D50021
Engine (EPA)
Table Of Contents ..................................................... 4
Parts Ordering Procedures ....................................... 5
Safety Message Alert Symbols .............................. 6-7
Rules For Safe Operation ...................................... 8-9
Pump Specifications/Dimensions ............................ 10
Engine Specifications .............................................. 11
General Information ................................................ 12
Pump Components ................................................. 13
Refueling ................................................................. 14
Basic Engine ........................................................... 15
Pre-Inspection (Engine) .......................................... 16
Pre-Set-up (Pump).................................................. 17
Initial Start-up (Engine) ...................................... 18-19
Maintenance (Pump) ......................................... 20-21
Maintenance (Engine)........................................ 22-23
Preparation for Long-Term Storage........................ 24
Troubleshooting (Engine)........................................ 26
Troubleshooting (Engine/Pump) ............................. 27
Explanation Of Parts Section Remarks................... 28
Suggested Spare Parts ........................................... 29
Pump Assy. ........................................................ 30-33
Crankcase Assy. ................................................ 34-35
Crankshaft Assy. ................................................ 36-37
Intake and Exhaust Assy.................................... 38-39
Air Cleaner Assy................................................. 40-41
Governor Assy. .................................................. 42-43
Cooling, Starting Assy. ....................................... 44-45
Fuel Tank Assy. .................................................. 46-47
Carburetor Assy. ................................................ 48-49
Flywheel Assy..................................................... 50-51
Electric Device Assy ........................................... 52-53
Terms and Conditions of Sale ................................. 54
Here's How to get Help ........................................... 56
Specification and part number
are subject to change without
notice.
PAGE 4 — QP- 40TE —OPERATION & PARTS MANUAL — REV. #0 (04/13/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS ORDERING PROCEDURES
When ordering parts,
please supply the following information:
❒
❒
❒
❒
❒
❒
❒
Dealeraccountnumber
Dealernameandaddress
Shipping address (if different than billing address)
Returnfaxnumber
Applicable model number
Quantity,part number and description of each part
Specifypreferredmethodofshipment:
✓
✓
✓
✓
✓
✓
FedEx or UPS Ground
FedEx or UPS Second Day or Third Day
FedEx or UPS Next Day
Federal Express Priority One
DHL
Note:Unlessotherwiseindicatedbycustomer, all
orders are treated as “Standard Orders”, and will
ship within 24 hours.We will make every effort to ship
“Air Shipments” the same day that the order is
received, if prior to 2PM west coast time. “Stock
Orders” must be so noted on fax or web forms.
Truck
Place Your Parts Order Via Web or Fax
For Even More Savings!
Here’s how to get help...
Please have the model and serial number
on hand when calling.
(Domestic USA Dealers Only)
MULTIQUIP CORPORATE OFFICE
18910 Wilmington Ave.
Carson, CA 90746
Email: [email protected]
800-421-1244
FAX: 310-537-3927
Extra Discounts!
All parts orders which include complete part numbers and
are received by our automated web parts order system, or
by fax qualify for the following extra discounts:
Ordered
via
Standard
orders
Stock orders
PARTS DEPARTMENT
800-427-1244
310-537-3700
MAYCO PARTS
800-306-2926
310-537-3700
SERVICE DEPARTMENT
800-421-1244
310-537-3700
TECHNICAL ASSISTANCE
800-478-1244
WARRANTY DEPARTMENT
800-421-1244, EXT. 279
310-537-3700, EXT. 279
($750 list and above)
FAX: 800-672-7877
FAX: 310-637-3284
Fax
3%
5%
10%
10%
Web
FAX: 800-672-7877
FAX: 310-637-3284
Special freight allowances
when you order 10 or more
line items via Web or Fax!**
FedEx Ground Service at no charge for freight
No other allowances on freight shipped by any other carrier.
FAX: 310-537-4259
FAX: 310-631-5032
FAX: 310-537-1173
**Common nuts, bolts and washers (all items under $1.00
list price) do not count towards the 10+ line items.
NOTE:DISCOUNTSARESUBJECTTOCHANGE
MULTIQUIP INC.
Direct TOLL-FREE access
to our Parts Department:
18910WILMINGTON AVENUE
POST OFFICE BOX 6254
CARSON, CALIFORNIA 90749
310-537-3700 • 800-421-1244
FAX:310-537-3927
Toll-free nationwide — 800-427-1244
INTERNET:www.multiquip.com
Toll-free FAX — 800-6-PARTS-7 (800/672-7877)
QP- 40TE — OPERATION & PARTS MANUAL — REV. #0 (04/13/05) — PAGE 5
Download from Www.Somanuals.com. All Manuals Search And Download.
QP- 40TE — SAFETY MESSAGE ALERT SYMBOLS
FORYOUR SAFETY ANDTHE SAFETY OF OTHERS!
HAZARD SYMBOLS
Potential hazards associated with the QP-40TE Trash Pump
operation will be referenced with Hazard Symbols which appear
throughout this manual, and will be referenced in conjunction
with Safety Message Alert Symbols.
Safety precautions should be followed at all times when
operating this equipment. Failure to read and understand the
Safety Messages and Operating Instructions could result in
injury to yourself and others.
This Owner's Manual has been
developed to provide complete
instructions for the safe and efficient
operation of the MultiquipModel
Lethal Exhaust Gases
Lethal Exhaust Gas Hazards
WARNING
Engine exhaust gases contain
poisonous carbon monoxide. This gas
is colorless and odorless, and can
cause death if inhaled. NEVER operate
this equipment in a confined area or
enclosed structure that does not provide
ample free flow air.
QP- 40TE Trash Pump. Refer to
the
engine
manufacturer's
instructions for data relative to its
safe operation.
Before using this pump, ensure
that the operating individual has
read and understands all
instructions in this manual.
Explosive Fuel Hazards
WARNING
SAFETY MESSAGE ALERT SYMBOLS
Gasoline is extremely flammable, and
its vapors can cause an explosion if
ignited. DO NOT start the engine near
spilled fuel or combustible fluids.
The three (3) Safety Messages shown below will inform you
about potential hazards that could injure you or others. The
Safety Messages specifically address the level of exposure to
the operator, and are preceded by one of three words: DANGER,
WARNING, or CAUTION.
DO NOT fill the fuel tank while the engine is running or
hot. DO NOT overfill tank, since spilled fuel could ignite if
it comes into contact with hot engine parts or sparks from
the ignition system. Store fuel in approved containers, in
well-ventilated areas and away from sparks and flames.
DANGER
You WILL be KILLED or SERIOUSLY INJURED
if you DO NOT follow these directions.
Burn Hazards
WARNING
WARNING
Engine components can generate extreme
heat. To prevent burns, DO NOT touch
these areas while the engine is running or
immediately after operations. Never
operate the engine with heat shields or heat
guards removed.
You CAN be KILLED or SERIOUSLY INJURED if
you DO NOT follow these directions.
CAUTION
You CAN be INJURED if you DO NOT follow
these directions.
Respiratory Hazards
WARNING
ALWAYS wear approved respiratory
protection when required.
PAGE 6 — QP- 40TE —OPERATION & PARTS MANUAL — REV. #0 (04/13/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
QP- 40TE — SAFETY MESSAGE ALERT SYMBOLS
Equipment Damage
Accidental Starting Hazards
CAUTION
CAUTION
Hazards
Other important messages are provided throughout this
manual to help prevent damage to your pump, other
property, or the surrounding environment.
ALWAYS place the ON/OFF switch in
the OFF position when the pump is not
in use.
This pump, other property, or the
surrounding environment could be
damaged if you do not follow
instructions.
Eye and Hearing Hazards
CAUTION
ALWAYS wear approved eye and
hearing protection.
QP- 40TE — OPERATION & PARTS MANUAL — REV. #0 (04/13/05) — PAGE 7
Download from Www.Somanuals.com. All Manuals Search And Download.
QP- 40TE — RULES FOR SAFE OPERATION
■
NEVER touch the hot exhaust manifold,
muffler or cylinder.Allow these parts to cool
before servicing engine or pump.
DANGER
Failure to follow instructions in this manual may lead to
serious injury or even death! This equipment is to be
operated by trained and qualified personnel only! This
equipment is for industrial use only.
The following safety guidelines should always be used when
operating the trash pump:
■
■
HighTemperatures – Allow the engine to cool before adding
fuel or performing service and maintenance functions. Contact
with hot components can cause serious burns.
GENERAL SAFETY
■
DO NOT operate or service this equipment before
readingthisentiremanual.
The engine of this pump
requires an adequate
free flow of cooling air.
NEVER! operate the
pump in any enclosed or
narrow area where free
flow of the air is
restricted. If the air flow
is restricted it will cause
■
■
This equipment should not be operated by persons under 18
years of age.
NEVER operate this equipment without proper protective
clothing, shatterproof glasses, steel-toed boots and other
protective devices required by the job.
serious damage to the
pump or engine and may cause injury to people and property.
Remember the pump's engine gives off DEADLY gases.
■
■
NEVER operate this equipment when not feeling
■
■
ALWAYS refuel in a well-ventilated area, away from sparks
well due to fatigue, illness or taking medicine.
and open flames.
ALWAYS use extreme caution when working with flammable
liquids. When refueling, stop the engine and allow it to cool.
DO NOT smoke around or near the machine. Fire or explosion
could result from fuel vapors, or if fuel is spilled on a hot
engine.
NEVER operate this equipment under the influence or drugs or
alcohol.
■
NEVER operate the pump in an explosive
atmosphere or near combustible
materials. An explosion or fire could result
causing severe bodily harm or even
death.
■
■
■
Whenever necessary, replace nameplate, operation and
safety decals when they become difficult read.
ALWAYS check the machine for loosened threads or bolts
before starting.
■
■
■
Topping-off to filler port is dangerous, as it
tends to spill fuel.
ALWAYS wear proper respiratory (mask) hearing and eye
protection equipment when operating the pump.
Refer to the Engine Owner's Manual for engine technical
questions or information.
NEVER use accessories or attachments, which are not
recommended by Multiquip for this equipment. Damage to
the equipment and/or injury to user may result.
■
Manufacturer does not assume responsibility for any accident
due to equipment modifications.
PAGE 8 — QP- 40TE —OPERATION & PARTS MANUAL — REV. #0 (04/13/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
QP- 40TE — RULES FOR SAFE OPERATION
■
■
■
■
NEVER run engine without air cleaner.Severe engine damage
■
High Temperatures – Always stop engine and allow the
engine to cool before adding fuel, oil or performing service
and maintenance functions. Contact with hot components can
cause serious burns.
may occur.
ALWAYS read, understand, and follow procedures in
Operator’s Manual before attempting to operate equipment.
■
NEVER disconnect any "emergency or safety devices".
These devices are intended for operator safety. Disconnection
of these devices can cause severe injury, bodily harm or even
death! Disconnection of any of these devices will void all
warranties.
ALWAYS be sure the operator is familiar with proper safety
precautions and operation techniques before using pump.
ALWAYS store equipment properly when it is not being used.
Equipment should be stored in a clean, dry location out of the
reach of children.
Maintenance Safety
■
■
■
■
NEVER leave the pump unattended, turn off engine when
unattended.
NEVER lubricate components or attempt service on a running
machine.
Unauthorized equipment modifications will void all
warranties.
■
ALWAYS allow the machine a proper amount of time to cool
before servicing.
NEVER pump volatile, explosive, flammable or low flash
point fluids.These fluids could ignite or explode.
■
■
Keep the machinery in proper running condition.
Fix damage to the machine immediately and always replace
broken parts, or missing decals.
■
■
NEVER operate the pump in an explosive atmosphere.
Before starting the pump, check that the clean-out cover is
securely fastened.
■
■
■
Dispose of hazardous waste properly.Examples of potentially
hazardous waste are used motor oil, fuel and fuel filters.
■
■
ALWAYS ensure pump is on level ground before use.
DO NOT use food or plastic containers to dispose of
hazardous waste.
Become familiar with the components of the pump before
operating.
DO NOT pour waste, oil or fuel directly onto the ground,
down a drain or into any water source.
■
NEVER pump corrosive chemicals or water containing toxic
substances. These fluids could create serious health and
environmental hazards. Contact local authorities for
assistance.
Emergencies
■
ALWAYS know the location of the
nearest fire extinguisher.
■
NEVER open the priming plug when pump is hot. Hot water
inside could be pressurized much like the radiator of an
automobile. Allow pump to cool to the touch before loosening
plug.
■
■
ALWAYS know the location of the nearest
first aid kit.
■
■
NEVER open the pump housing during operation or start the
pump with the clean-out cover removed.The rotating impeller
inside the pump can cut or sever objects caught in it.
In emergencies always know the location of the
nearest phone or keep a phone on the job site.
Also know the phone numbers of the nearest
ambulance, doctor and fire department. This
information will be invaluable in case of an
emergency.
NEVER block or restrict flow from discharge hose. Remove
kinks from discharge line before starting pump. Operation
with a blocked discharge line can cause water inside pump
to overheat.
■
■
ALWAYS fill the pump casing with water before starting the
engine. Failure to maintain water inside the pump housing
will cause severe damage to the pump.
In winter drain water from pump housing to prevent freezing.
QP- 40TE — OPERATION & PARTS MANUAL — REV. #0 (04/13/05) — PAGE 9
Download from Www.Somanuals.com. All Manuals Search And Download.
QP- 40TE — SPECIFICATIONS/DIMENSIONS (PUMP)
Table 1. Specifications (Pump)
Model
QP-40TE
Type
Trash Pump
Suction & Discharge Size
4.00 in. (101 mm.)
Maximum Pumping
Capacity
425 gallons/minute
(1600 liters/minute)
Pump
Max. Solids Diameter
Max. Lift
2.00 in. (50 mm.)
25 ft. (7.6 meters)
78 ft. (24.0 meters)
Max. Head
Dimension
(L x W x H)
29.1 x 27.4 X 31.5 in.
(740 X 685 X 800 mm.)
Dry Net Weight
240 lbs. (109 Kg.)
Figure 1. QP 40TE Pump Dimensions
PAGE 10 — QP- 40TE —OPERATION & PARTS MANUAL — REV. #0 (04/13/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
QP- 40TE — SPECIFICATIONS (ENGINE)
Table 2. Specifications (Engine)
Model
ROBIN EX-270D50021
Air-cooled 4 stroke, Single
Cylinder, OHV,
Horizontal Shaft Gasoline
Engine
Type
Displacement
265 cc
5.1 H.P./3600 R.P.M.
9.0 H.P./4000 R.P.M.
1.72 gallons (6.5 liters)
Unleaded Automobile Gasoline
1.16 quarts (1.1 liters)
Yes
Continuous Output
Max Output
Engine
Fuel Tank Capacity
Fuel
Lube Oil Capacity
Oil Alert System
Speed Control Method
Starting Method
Centrifugal Fly-weight Type
Recoil Start
Dimension
(L x W x H)
13.97 x 16.5 X 16.14 in.
(355 X 420 X 410 mm.)
Dry Net Weight
46.3 lbs (21 Kg.)
QP- 40TE — OPERATION & PARTS MANUAL — REV. #0 (04/13/05) — PAGE 11
Download from Www.Somanuals.com. All Manuals Search And Download.
QP- 40TE — GENERAL INFORMATION
APPLICATION
Suction Lift
The QP-40TE Trash Pump is designed to be used for de-
watering applications. Both the suction and discharge ports on
the QP-40TE pump use a 4-inch diameter opening, which allows
the pump to pump at a rate of approximately 425 gallons/minute
(gpm) or 1,600 liters/minute (lpm).
This pump is intended to be used for dewatering applications
and is capable of suction lifts up to 25 feet at sea level. For
optimal suction lift performance keep the suction hose or line as
short as possible. In general always put the pump as close to the
water as possible.
Self priming pumps are designed to purge air from the suction
line and create a partial vacuum in the pump body.The reduced
atmospheric pressure inside the pump allows water to flow
through the suction line and into the pump body.The centrifugal
force created by the rotating impeller pressurizes the water and
expels it from the pump.
Pump Support
The pump should always be placed on solid stationary
ground in a level position.
NEVER place the pump on soft soil. The suction hose or pipe
connection should always be checked for tightness and leaks. A
small suction leak in the hose or fittings could prevent the pump
from priming.
Power Plant
This trash pump is powered by an 11 horsepower air cooled 4-
stroke, single cylinder ROBIN EX- 270D gasoline engine that
incorporates a low "Oil Alert Feature"
Elevation
Elevations over 3,000 feet will effect the performance of the
pump. Due to less atmospheric pressure at higher altitudes, pump
DO NOT have the priming ability that they have at sea level.
Oil Alert Feature
In the event of low oil or no oil, the ROBIN EX- 270D engine has
a built-in oil alarm engine shut-down feature. In the event the oil
level is low the engine will automatically shut-down.
A general rule of thumb is that for every 1,000 feet of elevation
above sea level a pump will lose one foot of priming ability.
For example, in Flagstaff, Arizona where the elevation is
approximately 7,000 feet, the pump would have a suction lift of
only 18 feet rather than the 25 feet at sea level.
Trash Pump
Trash pump derive their name from their ability to handle a greater
amount of debris and solids than standard centrifugal pump.
These types of pumps generally handle solids up to 1/2 the size
of the discharge opening making them less likely to clog. Also
trash pumps are capable of handling water with 25% solids by
weight.
The advantage of using a trash pump is that it can be quickly
and easily disassembled in the field "without tools" and easily
cleaned when clogged.
PAGE 12 — QP- 40TE —OPERATION & PARTS MANUAL — REV. #0 (04/13/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
QP- 40TE — PUMP COMPONENTS
Figure 2 shows a typical application using the QP-40TE Trash pump.Please note that this pump is intended for the removal
of clean water and water containing some debris and solids. Maximum size of solids should not exceed 2 inches (50 mm)
in diameter. DO NOT set strainer on bottom of water bed. Placing the strainer above the water bed will prevent the pump
from drawing in excessive amounts of sand and foreign debris.
Figure 2. QP-40TE Pump Application
6. Suction Port – Connect a 4-inch inlet hose to this port.
1. Pump –The model QP-40TE is 4-inch trash pump used in
general de-watering applications. Typical dewatering
applications consist of manholes, septic tanks, fast and
slow seepage ditch water, silt water, mud water and muck
water.
Use two worm clamps to secure the hose.
7. Suction Hose – Connect this flexible rubber hose to the
suction port on the pump. Make sure that the hose lays flat
and is not kinked. Use only recommended type suction
hose. Contact Multiquip parts department for ordering
information
2. Fill Cap – Prior to operation, the pump casing should be
filled with water.Remove this cap to add water to the pump.
After the initial prime, a sufficient amount of water will be
retained in the casing so that the operator will not need to
re-prime later.
8. Clean-out Cover Handles –To gain access to the pump's
clean-out area, grip both handles, then pull to remove cover.
Make sure both locking knobs have been released before
attempting to remove clean-out cover.
If the casing is dry or has insufficient water, the pump will
have difficulty in priming which could lead to premature
mechanical seal wear thus causing damage to the pump.
9. Drain Plug – Remove this plug to drain water from the
pump.
3. Discharge Port – Connect a 4-inch discharge hose to this
10. Clean-out Cover – Remove cover to gain access to the
port.
clean-out area.
4. Worm Clamp – Used to secure the hose to the inlet and
outlet ports on the pump. Use two clamps to secure the
hose on the inlet side of the pump.
11. Locking Knobs– Turn both knobs clockwise to secure
clean-out cover, turn counter-clockwise to release cover.
12. Strainer – Always attach a strainer to bottom side of the
suction hose to prevent large objects and debris from
entering the pump. Strainer should be positioned so that it
will remain completely under water.Running the pump with
the strainer above water for long periods can damage pump.
5. Discharge Hose – Connect this flexible rubber hose to
the discharge port on the pump. Make sure that the hose
lays flat and is not kinked. Use only recommended type
discharge hose. Contact Multiquip parts department for
ordering information.
QP- 40TE — OPERATION & PARTS MANUAL — REV. #0 (04/13/05) — PAGE 13
Download from Www.Somanuals.com. All Manuals Search And Download.
QP- 40TE — REFUELING
DANGER
Adding fuel to the tank should be done only when
the engine is stopped and has had an opportunity to
cool down. In the event of a fuel spill, DO NOT attempt to start the
engine until the fuel residue has been completely wiped up, and the
area surrounding the engine is dry. If pump is placed in a truck bed
with a plastic liner, REMOVE pump from truck bed and place on
ground (Figure 3) to refuel. The possibility of fire or explosion
exists, due to static electricity.
PLASTIC
TRUCK-BED
LINER
DANGER
DO NOT ADD FUEL
TO TRASH PUMP IF
TRASH PUMP IS PLACED
INSIDE TRUCK-BED WITH
PLASTIC LINER. POSSIBILITY EXISTS
OF EXPLOSION OR FIRE DUE TO
STATIC ELECTRICITY.
Figure 3. Pump Refueling
PAGE 14 — QP- 40TE —OPERATION & PARTS MANUAL — REV. #0 (04/13/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
QP- 40TE — BASIC ENGINE
Figure 4. Engine Controls and Components
INITIAL SERVICING
5. Throttle Lever – Used to adjust engine RPM speed (lever
advanced forward SLOW, lever back toward operator
FAST).
The engine (Figure 4) must be checked for proper lubrication and
filled with fuel prior to operation. Refer to the ROBIN engine service
manualforinstructions anddetailsforproperoperationandservicing.
6. Recoil Starter (pull rope) – Manual-starting method. Pull
the starter grip until resistance is felt, then pull briskly and
smoothly.
1. Muffler – Used to reduce noise and emissions.
WARNING
7. Choke Lever – Used in the starting of a cold engine, or in
cold weather conditions. The choke enriches the fuel
mixture.
Engine components can generate extreme
heat.To prevent burns, DO NOT touch these
areas while the engine is running or
immediately after operating. NEVER operate
the engine with the muffler removed.
8. FuelValve Lever – OPEN to let fuel flow, CLOSE to stop
the flow of fuel.
9. Spark Plug – Provides spark to the ignition system. Set
spark plug gap to 0.6 - 0.7 mm (0.028 - 0.031 inch) Clean
spark plug once a week.
2. Air Cleaner – Prevents dirt and other debris from entering
the fuel system. Remove wing-nut on top of air filter
cannister to gain access to filter element.
10. Engine ON/OFF Switch – ON position permits engine
3. Fuel Tank – Holds unleaded gasoline. For additional
starting, OFF position stops engine operations.
information refer to ROBIN engine owner's manual.
11. Oil Drain Plug – Remove this plug to drain engine oil from
4. Fuel Filler Cap – Remove this cap to add unleaded
gasoline to the fuel tank. Make sure cap is tightened
securely. DO NOT over fill.
the crankcase.
12. Oil Dipstick/ Filler Cap– Remove the filler cap dipstick
when checking the engine oil level. Add engine oil through
this filler port. See Table 5 for recommended type engine
oil.
DANGER
Adding fuel to the tank should be done only
when the engine is stopped and has had an
opportunity to cool down. In the event of a fuel
spill, DO NOT attempt to start the engine until
the fuel residue has been completely wiped
up, and the area surrounding the engine is dry.
Operating the engine without an air
filter, with a damaged air filter, or a
filter in need of replacement will
allow dirt to enter the engine,
causing rapid engine wear.
QP- 40TE — OPERATION & PARTS MANUAL — REV. #0 (04/13/05) — PAGE 15
Download from Www.Somanuals.com. All Manuals Search And Download.
QP- 40TE — PRE-INSPECTION (ENGINE)
3. Insertandremovethedipstickwithoutscrewingitintothefiller
neck. Check the oil level shown on the dipstick.
CAUTION
4. If the oil level is low (Figure 6), fill to the edge of the oil filler
holewiththerecommendedoiltype(Table3).Maximum oil
capacity is 1.16 quarts (1.1 liters)
NEVER operate the pump in a confined
area or enclosed area structure that does
not provide ample free flow of air.
ALWAYS wear approved eye and hearing
protection before operating the pump.
Before Starting
Figure 6. Engine Oil Dipstick (Oil Level)
Table 3. Oil Type
1.
Read safety instructions at the
beginning of manual.
2.
Clean the pump, removing dirt and
dust, particularly the engine
cooling air inlet, carburetor and air
cleaner.
Season
Summer
Spring/Fall
Winter
Temperature
25°C or Higher
25°C~10°C
Oil Type
SAE 10W-30
SAE 10W-30/20
SAE 10W-10
3.
4.
5.
Check the air filter for dirt and dust. If air filter is dirty, replace
air filter with a new one as required.
0°C or Lower
Check carburetor for external dirt and dust. Clean with dry
compressed air.
Check fastening nuts and bolts for tightness.
DANGER - EXPLOSIVE FUEL
Motor fuels are highly flammable and can be
dangerous if mishandled. DO NOT smoke while
refueling. DO NOT attempt to refuel the pump if
the engine is hot! or running.
Engine Oil Check
1.
To check the engine oil level, place the pump on secure
level ground with the engine stopped.
2.
Remove the filler dipstick from the engine oil filler hole
(Figure 5) and wipe clean.
Fuel Check
1. Remove the gasoline cap located on top of fuel tank.
2. Visually inspect to see if the fuel level is low. If fuel is low,
replenish with unleaded fuel.
3. When refueling, be sure to use a strainer for filtration. DO
NOT top-off fuel. Wipe up any spilled fuel immediately!
Figure 5. Engine Oil Dipstick (Removal)
PAGE 16 — QP- 40TE —OPERATION & PARTS MANUAL — REV. #0 (04/13/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
QP- 40TE — PRE-SETUP (PUMP)
Before Starting
Suction and discharge hoses are
1. Read safety instructions at the
beginning of manual.
NOTE
available from Multiquip. Contact
your nearest dealer for more
information.
2. Place pump as near to water as
possible,onafirmflat,levelsurface.
3. Toprimepump,removefillcap(Figure2)andfillpumpcasing
with water.If the pump casing is not filled with water before
starting, it will not begin pumping.
5. The discharge hose is usually a collapsible (thin-walled)
hose, however if a thin-walled discharge hose is not avail-
able, a rigid suction hose can be substituted in its place.
6. Make sure the suction strainer (Figure 2) is clean and
securely attached to the water end of the suction hose. The
strainer is designed to protect the pump by preventing large
objects from being pulled into the pump.
CAUTION
Pump casing must be filled with water before using
pump. Otherwise pump will not be able to begin pumping.
CAUTION
The strainer should be positioned so it will remain completely
under water. Running the pump with the strainer above
water for long periods can damage the pump.
WARNING
DO NOT open fill cap if pump is hot! Water inside
may be under pressure.
CAUTION
DO NOT pump flammable fluids, corrosive chemicals or fluids
containing toxic substances. These fluids can create potentially
dangerous health and environmental hazards. Contact local
authorities for assistance.
4. Checkforleaksbetweenpumpandengine.Ifwaterisleaking
between the pump and engine housing, the seal inside the
pumpmaybewornordamaged.Continued operationofthe
pumpisnot recommended.Furtherusageofthe pumpunder
thisconditionsmaycauseseverewaterdamagetoengine.
Hoses and Clamps
1. Check that all hoses are securely attached to the pump.
Make certain suction hose (Figure 2) does not have any air
leakage.Tighten hose clamps and couplings as required.
CAUTION
This pump uses a water-cooled mechanical seal to prevent
water from seeping into the engine. The passage of water
through the pump casing lubricates the seal and prevents it
from overheating. NEVER! operate the pump without water in
the casing as this will cause damage to the mechanical seal.
2. Itisrecommendedthat 2 clampsbeusedwhensecuringthe
suction hose to the inlet side (suction) of the pump.
3. Remember suction hoses must be rigid enough not to
collapse when the pump is in operation.
4. Check that the discharge hose (Figure 2) is not restricted.
Place hose so that it lays as straight as it is possible on the
ground. Remove any twists or sharp bends from hose which
may block the flow of water.
QP- 40TE — OPERATION & PARTS MANUAL — REV. #0 (04/13/05) — PAGE 17
Download from Www.Somanuals.com. All Manuals Search And Download.
QP- 40TE — INITIAL START-UP (ENGINE)
3. Place the choke lever (Figure 9) in the "OPEN " position if
starting a cold engine.
CAUTION
DO NOT attempt to operate the pump until
the Safety, General Information and
Inspection sections of this manual have
been read and
understood.
thoroughly
This section is intended to assist the operator with the initial
start-up of the trash pump. It is extremely important that this
section be read carefully before attempting to use the pump in
the field.
Figure 9. Engine Choke Lever (Open)
Starting the Engine
1. Place the engine fuel valve lever (Figure 7) to the "ON"
4. Placethechokelever(Figure10)inthe"CLOSED"position
if starting a warm engine or the temperature is warm.
position.
Figure 7. Engine FuelValve Lever (ON Position)
2. Move the throttle lever (Figure 8) away from the slow
position, about 1/3 of the way toward the fast position.
Figure 10. Engine Choke Lever (Closed)
5. Place the engine ON/OFF switch (Figure 11) in the "ON "
position.
Figure 8. Throttle Lever (1/3 Start Position)
Figure 11. Engine ON/OFF Switch (ON Position)
PAGE 18 — QP- 40TE —OPERATION & PARTS MANUAL — REV. #0 (04/13/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
QP- 40TE — INITIAL START-UP (ENGINE)
6. Grasp the starter grip (Figure 12) and slowly pull it out.The
CAUTION
resistancebecomesthehardestatacertainposition,corre-
spondingtothecompressionpoint.Pullthestartergripbriskly
andsmoothlyforstarting.
ALWAYS run engine at full speed while pumping.
Stopping The Engine
Normal Shutdown
1. Movethethrottlelever tothe IDLEposition (Figure15)and
run the engine for three minutes at low speed.
Figure 12. Starter Grip
7. If the engine has started, slowly return the choke lever
(Figure 13) to the CLOSED position. If the engine has not
started repeat steps 1 through 6.
Figure 15.Throttle Lever (Idle)
2. Aftertheenginecools,turntheengineON/OFFswitchtothe
“OFF” position (Figure 16).
Figure 13. Choke Lever (Closed)
8. Beforethepumpisplacedintooperation,runtheenginefor
severalminutes. Checkfor fuelleaks,andnoisesthatwould
associate with a lose component.
Figure 16. Engine ON/OFF Switch (OFF)
3. Place the fuel shut-off lever (Figure 17) in the OFF
position.
9. To begin pumping, place the throttle lever (Figure 14) in the
"RUN"position.
Figure 17. Fuel Valve Lever (OFF)
Emergency Showdown
1. MovethethrottleleverquicklytotheIDLE position,andplace
the engine ON/OFF switch in the OFF position.
Figure 14. Throttle Lever (Run)
QP- 40TE — OPERATION & PARTS MANUAL — REV. #0 (04/13/05) — PAGE 19
Download from Www.Somanuals.com. All Manuals Search And Download.
QP- 40TE — MAINTENANCE (PUMP)
Pump Vacuum Test
Adjusting Impeller Clearance
1. If it is necessary to replace impeller or volute, be sure
clearance between impeller and volute is adjusted
correctly.
CAUTION
DO NOT attempt to start the engine unless the pump has
previously been primed with water.Severe pump damage
will occur if pump has not been primed.
2. The impeller should be as close to the volute as possible
without rubbing against it. Clearance is adjusted by
adding or removing shims from behind the impeller.
To perform the pump vacuum test do the following:
3. Check clearance between impeller and insert by slowly
pulling starter rope to turn impeller. Remove spark plug
to make it easier to turn impeller.
1. Remove the pump fill cap, and fill the pump with water.
2. Start the engine as outlined in the initial start-up section,
and wait for the pump to begin pumping.
It is important not to remove too
many shims or the clearance
between the impeller and volute
will become too wide and pump
performance will be reduced.
Remember as the impeller wear
3. As shown in Figure 17 (next page), place a water hose
inside the discharge opening of the pump, and turn on
the water.This flow of water into the discharge opening
will prevent the pump from running dry.
down, additional shims may be required to maintain the
clearance between the impeller and insert.
4. Place the Pump Vacuum Tester (P/N 7000030) over
the pump suction (inlet) opening (Figure 18) with the
vacuum gauge facing upwards. It may be necessary to
apply a small amount of water around the rubber seal of
the vacuum tester to make a good suction fit.
4. Check the impeller every six months for wear, and for
clearance between the impeller face and the volute. Also
check the shaft seal for wear, as well as the shaft sleeve.
5. Check and make sure that there are no air leaks between
the vacuum tester and the inlet port on the pump. If air
leaks are present reseat vacuum tester.
Pump Cleaning
After pumping water containing large amounts of dirt and
debris, perform the following:
6. Run the pump for a few minutes while monitoring the
vacuum gauge. If the gauge indicates a reading between
-25 and -20 in. Hg. (inches of mercury) then it can be
assumed that the pump is working correctly.
1. Remove the drain plug from the pump housing (Figure 1)
and drain any water left in the pump.
2. Loosen the two locking hand knobs (turn counter-
clockwise) and remove clean-out cover.
3. Clean and remove dirt, debris from pump casing.Inspect
impeller and volute for wear. Replace any damaged or
worn parts.
25 in. Hg (inches of mercury)
translates into 25 feet of lift at sea
level.
CAUTION
The impeller may develop sharp edges. Use extreme care
7. If the vacuum tester gauge indicates a reading
below -20 in. Hg, it can then be assumed that the pump
is not functioning correctly, and corrective action needs
to be taken.
when cleaning around the impeller to prevent being cut.
6. To test the flapper valve, shut down the engine. The
vacuum tester should remain attached to the pump
suction inlet port by vacuum. This indicates the pump's
flapper valve is seating properly to hold water in the
suction hose when the engine is stopped.This prevents
backflow and allows for faster priming when the engine
is restarted.
PAGE 20 — QP- 40TE —OPERATION & PARTS MANUAL — REV. #0 (04/13/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
QP- 40TE — MAINTENANCE (PUMP)
Figure 18. Pump Vacuum Tester
QP- 40TE — OPERATION & PARTS MANUAL — REV. #0 (04/13/05) — PAGE 21
Download from Www.Somanuals.com. All Manuals Search And Download.
QP- 40TE — MAINTENANCE (ENGINE)
Engine Maintenance
Perform engine maintenance procedures as referenced by
Table 4 below:
Table 4. Engine Maintenance Schedule
FIRST
EVERY
EVERY
EVERY
YEAR
OR
EVERY
2 YEARS
OR
MONTH 3 MONTHS 6 MONTHS
OR
DESCRIPTION (3)
OPERATION
BEFORE
OR
OR
10 HRS.
25 HRS.
50 HRS.
100 HRS.
200 HRS.
CHECK
CHANGE
CHECK
X
Engine Oil
X
X
X
Air Cleaner
All Nuts & Bolts
Spark Plug
CHANGE
X (1)
Re-tighten If
Necessary
CHECK-CLEAN
REPLACE
CHECK
X
X
X
Cooling Fins
Spark Arrester
Fuel Tank
CLEAN
X
X
CLEAN
Fuel Filter
CHECK
X
Idle Speed
CHECK-ADJUST
CHECK-ADJUST
CHECK
X (2)
Valve Clearance
Fuel lines
X (2)
Every 2 years (replace if necessary) (2)
(1) Service more frequently when used in DUSTY areas.
(2) These items should be serviced by your servic dealer, unless you have the proper tools and are mechanically
proficient. Refer to the HONDA shop Manual for service procedures
(3) For commercial use, log hours of operation to determine proper maintenance intervals.
Reference manufacturer engine
manual for specific servicing
instructions.
PAGE 22 — QP- 40TE —OPERATION & PARTS MANUAL — REV. #0 (04/13/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
QP- 40TE — MAINTENANCE (ENGINE)
Maintenance
DANGER
Performtheenginemaintenanceproceduresasindicatedbelow:
DO NOT use gasoline as a cleaning solvent, because that
would create a risk of fire or explosion.
DAILY
■
Thoroughly remove dirt and oil from the engine and control
area.Clean or replace the air cleaner elements as necessary.
Check and retighten all fasteners as necessary. Check the
spring box and bellows for oil leaks. Repair or replace as
needed.
ENGINEAIRCLEANER
1. Remove the air cleaner cover and foam filter element as
shown in Figure 21.
WEEKLY
2. Tap the paper filter element (Figure 21) several times on a
hard surface to remove dirt, or blow compressed air [not
exceeding 30 psi (207 kPa, 2.1 kgf/cm2)] through the filter
elementfromtheaircleanercaseside.NEVER brushoffdirt.
Brushingwillforcedirtintothefibers.Replacethepaperfilter
element if it is excessively dirty.
■
Remove the fuel filter cap and clean the inside of the fuel
tank.
■
■
Remove or clean the filter at the bottom of the tank.
Remove and clean the spark plug (Figure 19), then adjust
the spark gap to 0.028 ~0.031 inch (0.6~0.7 mm).This unit
has electronic ignition, which requires no adjustments.
3. Cleanfoamelementinwarm,soapywaterornonflammable
solvent. Rinseanddrythoroughly. Diptheelementinclean
engineoilandcompletelysqueezeouttheexcessoilfromthe
element before installing.
Figure 19. Spark Plug Gap
ENGINEOIL
1. Drain the engine oil when the oil is warm as shown in
Figure 20.
2. Remove the oil drain bolt and sealing washer and allow
the oil to drain into a suitable container.
3. Replace engine oil with recommended type oil as listed
in Table 3. Engine oil capacity is 1.16 quarts (1.1 liters).
DO NOT overfill.
4. Install drain bolt with sealing washer and tighten se-
curely.
Figure 21. Engine Air Cleaner
Figure 20. Engine Oil (Draining)
QP- 40TE — OPERATION & PARTS MANUAL — REV. #0 (04/13/05) — PAGE 23
Download from Www.Somanuals.com. All Manuals Search And Download.
QP- 40TE — PREPARATION FOR LONG -TERM STORAGE
Pump Storage
For storage of the pump for over 30 days, the following is
required:
z
z
Drain the fuel tank completely.
Run the engine until the fuel in the injection system is
completely consumed.
z
Completely drain used oil from the engine crankcase
and fill with fresh clean oil, then follow the procedures
described in the engine manual for engine storage.
z
z
Remove the drain plug from the pump and drain out any
water from left in the housing.
Remove the pump cover and clean inside of pump
housing. Coat inside of pump housing with a light film of
oil to reduce corrosion. A spray can of oil works well for
this application.
z
z
z
Cover suction and discharge ports with duct tape to
prevent any foreign matter from falling into pump.
Cover pump and engine with plastic covering or
equivalent and store in a clean, dry place.
To protect the water cooled-seals, place one-half pint of
lubricating oil (new or used) through the discharge
opening on the pump and crank the engine several times.
This will prevent excessive corrosion and also keep the
mechanical seal lubricated.
PAGE 24 — QP- 40TE —OPERATION & PARTS MANUAL — REV. #0 (04/13/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE PAGE
QP- 40TE — OPERATION & PARTS MANUAL — REV. #0 (04/13/05) — PAGE 25
Download from Www.Somanuals.com. All Manuals Search And Download.
QP- 40TE — TROUBLESHOOTING (ENGINE)
TABLE 5. ENGINE TROUBLESHOOTING
SYMPTOM
Difficult to start
POSSIBLE PROBLEM
SOLUTION
Ignition plug being bridge?
Carbon deposit at ignition?
Check ignition system.
Clean or replace ignition.
Replace insulators.
Fuel is available but spark plug
will not ignite. (Power available
at high tension cable).
Short circuit due to defective
insulators?
Improper spark gap?
Set spark plug gap to the correct gap.
Check stop switch circuit. Replace stop switch if defective.
Replace ignition coil.
Short circuit at stop switch?
Ignition coil defective?
Fuel is available but spark plug
will not ignite. (Power NOT
available at high tension cable).
Muffler clogged with carbon
deposits?
Clean or replace muffler.
Mixed fuel quality is
inadequate?
Check fuel to oil mixture.
Fuel is available and spark plug
ignites (compression normal).
Fuel in use inadequate (water,
dust)?
Flush fuel sytem and replace with fresh fuel.
Air Cleaner clogged?
Defective cylinder head gasket?
Cylinder worn?
Clean or replace air cleaner.
Tighten cylinder head bolts or replace head gasket.
Replace cylinder.
Fuel is available and spark plug
ignites (compression low ).
Spark plug loose?
Tighen spark plug.
Operation not satisfactory
Air cleaner clogged?
Air in fuel line?
Bleed (remove air) from fuel line.
Adjust carbureator float
Not enough power available
(compression normal, no miss-
firing).
Fuel level in carbureator float
chamber improper?
Carbon deposits in cylinder?
Ignition coil defective?
Clean or replace cylinder
Flush fuel sytem and replace with fresh fuel.
Replace ignition wires, clean ignition.
Flush fuel sytem and replace with fresh fuel.
Not enough power available
(compression normal, miss-
firing).
Ignition plug often shorts?
Fuel in use inadequate (water,
dust)?
Excessive carbon depostion in
combustion chamber?
Clean or replace crankcase.
Clean or replace muffler.
Engine overheats.
Exhaust or muffler clogged with
carbon.
Spark plug heat value incorrect? Replace spark plug with correct type spark plug.
PAGE 26 — QP- 40TE —OPERATION & PARTS MANUAL — REV. #0 (04/13/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
QP- 40TE — TROUBLESHOOTING (ENGINE/PUMP)
TABLE 5. ENGINE TROUBLESHOOTING (Continued)
SYMPTOM
POSSIBLE PROBLEM
SOLUTION
Operation not satisfactory
Governor adjustment improper?
Governor spring defective?
Fuel flow erratic?
Adjust governor to correct lever.
Clean or replace ignition.
Check fuel line.
Rotational speed fluctuates.
Air taken in through suction
line?
Check suction line.
Dust in rotating part?
Spring spring failure?
Clean recoil starter assembly.
Replace sprial spring.
Recoil starter not working
properly.
TABLE 6 PUMP TROUBLESHOOTING
POSSIBLE PROBLEM
SYMPTOM
SOLUTION
Not enough priming water in the housing?
Engine speed too low?
Add water.
Increase throttle.
Clean strainer.
Strainner plugged?
Suction hose damaged?
Replace or repair hose, and clamps
Check that fittings are tight and properly sealed.
Move pump closer to water.
Air leak at suction port?
Pump does not take on water.
Pump is located too high above water line?
Debris collecting in pump housing?
Clean pump housing.
Adjust clearance by adding shims or replace impeller.
Min. .006" - Max. .020"
Too much distance between impeller and volute.
Water leaking out weep hole between pump and Check condition of mechanical seal and gaskets,
engine?
between pump end and engine housing.
Engine speed too low?
Increase throttle speed.
Pump takes in water, little or no Suction strainer partially plugged?
Clean strainer.
discharge.
Impeller/Volute worn?
Adjust clearance by adding shims or replace
impeller/volute
Tighten, replace or add clamp. (Keep extra seals on
pump)
Fittings/clamps are not sealed properly?
Suction hose leaks at inlet.
Hose diameter is too large?
Use smaller diameter hose or replace hose.
Check pressure, add additional clamp.
Check hose.
Pressure too high?
Discharge does not stay on
coupling.
Hose kinked or end blocked?
Impeller jammed or blocked?
Open pump cover and clean dirt and debris from
inside housing.
Impeller does not turn: pump is
hard to start.
Adjust clearance by removing shim from behind
impeller.
Impeller and volute binding?
Defective engine?
See Hatz Diesel Engine Owner's Manual.
QP- 40TE — OPERATION & PARTS MANUAL — REV. #0 (04/13/05) — PAGE 27
Download from Www.Somanuals.com. All Manuals Search And Download.
QP- 40TE — EXPLANATION OF PARTS SECTION REMARKS
The following section explains the different symbols and remarks QTY. Column
used in the Parts section of this manual. Use the help numbers
found on the back page of the manual if there are any questions.
Numbers Used - Item quantity can be indicated by a number,
a blank entry, or A/R.
A/R (As Required) is generally used for hoses or other parts
that are sold in bulk and cut to length.
The contents and part numbers listed in the parts section are
subject to change without notice. Multiquip does not
guarantee the availability of the parts listed.
A blank entry generally indicates that the item is not sold
separately. Other entries will be clarified in the “Remarks”
Column.
Sample Parts List:
REMARKS Column
NO. PART NO. PART NAME
QTY. REMARKS
Some of the most common notes found in the “Remarks”
Column are listed below. Other additional notes needed to
describe the item can also be shown.
1
2
2
3
4
12345
BOLT .......................1.... INCLUDES ITEMS W/
WASHER, 1/4 IN. ........... NOT SOLD SEPARATELY
WASHER, 3/8 IN. ....1.... MQ-45TONLY
HOSE .................... A/R.. MAKE LOCALLY
BEARING ................1.... S/N 2345B AND UP
*
*
*
12347
12348
12349
Assembly/Kit - All items on the parts list with the same unique
symbol will be included when this item is purchased.
Indicated by:
“INCLUDES ITEMS W/(unique symbol)”
NO. Column
Unique Symbols - All items with same unique symbol
Serial Number Break - Used to list an effective serial number
range where a particular part is used.
( , #,
+
, %, or >) in the number column belong to the same
*
assembly or kit, which is indicated by a note in the “Remarks”
column.
Indicated by:
“S/N XXXXX AND BELOW”
“S/N XXXX AND ABOVE”
“S/N XXXX TO S/N XXX”
Duplicate Item Numbers - Duplicate numbers indicate
multiple part numbers are in effect for the same general item,
such as different size saw blade guards in use or a part that
has been updated on newer versions of the same machine.
Specific Model Number Use - Indicates that the part is used
only with the specific model number or model number variant
listed. It can also be used to show a part is NOT used on a
specific model or model number variant.
When ordering a part that has more
than one item number listed, check
the remarks column for help in
determining the proper part to order.
NOTE
Indicated by:
“XXXXX ONLY”
“NOT USED ON XXXX”
“Make/Obtain Locally” - Indicates that the part can be
purchased at any hardware shop or made out of available
items. Examples include battery cables, shims, and certain
washers and nuts.
PART NO. Column
Numbers Used - Part numbers can be indicated by a number,
a blank entry, orTBD.
TBD (To Be Determined) is generally used to show a part that
has not been assigned a formal part number at time of
publication.
“Not Sold Separately” - Indicates that an item cannot be
purchased as a separate item and is either part of an
assembly/kit that can be purchased, or is not available for
sale through Multiquip.
A blank entry generally indicates that the item is not sold
separately or is not sold by Multiquip. Other entries will be
clarified in the “Remarks” Column.
PAGE 28 — QP- 40TE —OPERATION & PARTS MANUAL — REV. #0 (04/13/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
QP- 40TE — SUGGESTED SPARE PARTS
QP-40TE 1 TO 5 UNITS WITH ROBIN
EX- 270D50021 ENGINE
1 to 5 Units
Qty.
P/N
Description
3
1
1
6
6
2
1
5
5
1
1
1
KIT40TE
KIT, MECHANICAL SEAL, SLEEVE, O-RINGS
IMPELLER
1464040030
1401350350
0631211100
0480350300
CHECK VALVE
DRAIN CAP
O-RING, DRAIN CAP
12470001900001 DRAIN COVER SET KNOB
0742214100
2793260707
0650140150
0430430060
0641360010
2795011008
STEEL STRAINER
ELEMENT AIR CLEANER
SPARK PLUG (ROBIN)
CAP, FUEL TANK (ROBIN)
FUEL, FILTER
STARTER ROPE
QP- 40TE — OPERATION & PARTS MANUAL — REV. #0 (04/13/05) — PAGE 29
Download from Www.Somanuals.com. All Manuals Search And Download.
QP- 40TE — PUMP ASSY.
PUMP ASSY.
PAGE 30 — QP- 40TE —OPERATION & PARTS MANUAL — REV. #0 (04/13/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
QP- 40TE — PUMP ASSY.
PUMP ASSY.
NO.
1
2
3
4
5
6
7
8
PART NO.
PART NAME
QTY.
1
1
1
1
1
1
2
1
1
2
2
2
2
1
1
4
1
1
2
1
1
3
1
1
2
1
1
1
1
4
2
REMARKS
EX270D50021
14120600100001
14180600210001
14140000900001
14140000900001
12681001700001
12471002500001
1464040030
ENGINE, ROBIN
CASING
CASING COVER
DELIVERY COVER NPT4"
SUCTION COVER NPT4"
DRAIN COVER
DRAIN COVER HANDLE
IMPELLER
9
1412000130
VOLUTE CASING
10
11
12
13
14
15
16
17
18
12470001900001
12470002000001
1247200270
DRAIN COVER SET KNOB
DRAIN COVER PUSH PLATE
HINGE BOLT M12 x 90
HINGE PIN DIA 12 x 65
BASE
ENGINE BASE
CUSHION RUBBER
1247220280
1464214010P001
14642140200014
0723302546
1401350350
1401330360
0489312300
0489352400
0482200240
0480350300
1412390300
0631211100
0631211100
0801123530
0811883034
0852834525
0852854525
0141050825
CHECK VALVE
DELIVERY COVER PACKING
O-RING (VOLUTE CASING) DIA 3.1 x 228
O-RING (DRAIN COVER) DIA 3.5 x 240
O-RING (MECHANICAL SEAL SLEEVE) S24
O-RING (FLOODING-DRAIN CAP) P30
CASING COVER PACKING
FLOODING CAP PF1"
19
*
20
*
21
*
22
23
24
25
DRAIN CAP PF1"
26
MECHANICAL SEAL DIA 30
MECHANICAL SEAL SLEEVE
ADJUST LINER DIA 45 x 25.4 10.3
ADJUST LINER DIA 45 x 25.4 10.5
SCREW (DRAIN COVER HANDLE) M8 x 25
SCREW (VOLUTE CASING) M8 x 25
*
27
*
28
*
28
29
*
30
0141090825
QP- 40TE — OPERATION & PARTS MANUAL — REV. #0 (04/13/05) — PAGE 31
Download from Www.Somanuals.com. All Manuals Search And Download.
QP- 40TE — PUMP ASSY.
PUMP ASSY.
PAGE 32 — QP- 40TE —OPERATION & PARTS MANUAL — REV. #0 (04/13/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
QP- 40TE — PUMP ASSY.
PUMP ASSY.
NO.
31
32
PART NO.
PART NAME
QTY.
REMARKS
0151151025
0151140536
0151151230
STUD BOLT (CASING) M10 x 35 x 10 x 15
STUD BOLT (CASING CVR) 5/16" x 52 x 15 x 15
STUD BOLT(DELIVERY/SUCTION COVER)
M12 x 45 x 15 x 20
4
4
8
33
34
35
36
37
0191150725
0105051045
0205450120
0205450100
BOLT (IMPELLER) 3/8-24 UNF x25
BOLT (ENGINE) M10 x 25
NUT (DELIVERY/SUCTION COVER) M12
NUT (CUSHION RUBBER, CASING, ENGINE,
PUMP M10
1
4
8
18
38
39
40
41
42
43
44
45
46
47
48
49
0205450055
0451250120
0451250100
0451250080
0458220080
0401450100
43342012400011
0105051035
0641400430
0520040425
0742214100
KIT40TE
NUT, 5/16"
4
8
19
10
4
4
1
2
2
1
1
SPRING WASHER M12
SPRING WASHER M10
SPRING WASHER M8
WASHER M8
WASHER M10
IMPELLER WASHER DIA 38 x 11 x 6T
BOLT (PUMP) M10 x 35
SPLIT PIN
KEY
STRAINER
KIT, MECHANICAL SEAL, SLEEVE, O-RINGS ....... 1 ....... INCLUDES ITEMS W/
*
QP- 40TE — OPERATION & PARTS MANUAL — REV. #0 (04/13/05) — PAGE 33
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EX270D50021 ENGINE — CRANKCASE ASSY.
CRANKC
PAGE 34 — QP- 40TE —OPERATION & PARTS MANUAL — REV. #0 (04/13/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EX270D50021 ENGINE — CRANKCASE ASSY.
CRANKCASE ASSY.
NO
10
20#
26#
PART NO
PART NAME
QTY.
REMARKS
2791010251
2371420203
2771601001
0440300160
0600300341
2771501103
0105080250
0105060410
0440060020
0401140030
0211140020
2791100121
0440300160
0600300370
2774500421
2774190103
2796360113
2796500103
CRANKCASE CP, W/ OIL SENSOR ................................ 1 ..........INCLUDES ITEMS W/
*
VALVE GUIDE,5.5DX9.5DX27L
STEM SEAL, 5DX11.6DX15DX7.8T
OIL SEAL, 28.8DX45DX7T
BALL BEARING, BB6206, 30DX62DX16B
PIPE KNOCK, 10DX8.5DX14L
STUD, M8X1.25X25L
2
1
1
1
2
2
2
1
2
2
30
*
40
*
50
*
60#
70#
STUD, M6X1.0X107L
75
80
OIL SEAL, 5.6DX10DX2.5T
PLUG, M14X1.5 X20DX12L
GASKET, 14.1DX19DX2.3T
MAIN BEARING COVER C ..............................................1........... INCLUDES ITEMS W/ $
OIL SEAL, 28.8DX45DX7T
BALL BEARING
GOVERNOR GEAR CP, 52.5DX29T N=33
GOVERNOR SLEEVE, 6DX7.6DX16DX26L
OIL GAUGE, M22X1.5 L=67.5+18
FILLER PLUG, M22X1.5 L=12+18
GASKET,
GASKET,
FLANGE BOLT
*
90+
210
220$
230$
250
260
270
275
1
1
1
1
1
1
1
1
6
280+ 0213200050
281
300
610
0213200050
0010408350
2791300111
CYLINDER HEAD CP ...................................................... 1 ..........INCLUDES ITEM W/#
GASKET, HEAD
FLANGE BOLT, M8X1.25 X68L
FLANGE BOLT
1
4
1
1
1
2
4
1
ROCKER COVER CP
GASKET, ROCKER COVER, T=0.7
PIPE KNOCK, 10DX8.5DX14L
FLANGE BOLT, M6X1.0X12L
RUBBER PIPE, 8DX11D
GASKET SET ..................................................................1........... INCLUDES ITEMS W/+ &
ITEM 340 IN THE INTAKE
& EXHAUST ASSY
QP- 40TE — OPERATION & PARTS MANUAL — REV. #0 (04/13/05) — PAGE 35
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EX270D50021 ENGINE — CRANKSHAFT ASSY.
CRANKSHAFT, PISTON ASSY.
PAGE 36 — QP- 40TE —OPERATION & PARTS MANUAL — REV. #0 (04/13/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EX270D50021 ENGINE — CRANKSHAFT ASSY.
CRANKSHAFT, PISTON ASSY.
NO
10
PART NO
PART NAME
QTY.
REMARKS
2792100131
2792030141
0180180010
0323030010
2792250120
2792300103
2792330103
2792340103
2792340303
2792340403
2792351107
2792351207
2792351307
0565180010
CRANKSHAFT CP, 1" PUMP
CRANKSHAFT CP, METRIC PUMP 25MM
FLANGE NUT, M18X31DX14H
WOODRUFF KEY, 3BX6HX16D
1
1
1
1
10
50
70
310
320#
350
360
360
360
370
370
370
380
CONNECTING ROD ASSY. ............................. 1 ............INCLUDES ITEM W/#
CONNECTING ROD BOLT, M7X1.0X40L
PISTON PIN, 18DX13DX53L
PISTON, STD. 74.4DX43H
PISTON, OVERSIZE 0.25 MM
PISTON, OVERSIZE 0.50 MM
PISTON RING SET, STD.
PISTON RING SET, OVERSIZE 0.25 MM
PISTON RING SET, OVERSIZE 0.50 MM
CLIP, 17.3DX1.6D
2
1
1
1
1
1
1
1
2
QP- 40TE — OPERATION & PARTS MANUAL — REV. #0 (04/13/05) — PAGE 37
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EX270D50021 ENGINE — INTAKE AND EXHAUST ASSY.
INTAKE AND EXHAUST GROUP ASSY.
PAGE 38 — QP- 40TE —OPERATION & PARTS MANUAL — REV. #0 (04/13/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EX270D50021 ENGINE — INTAKE AND EXHAUST ASSY.
INTAKE AND EXHAUST GROUP ASSY.
NO.
10
25
27
34
35
37
38
60
70
80
90
95
PART NO.
PART NAME
QTY.
1
1
1
1
1
1
1
2
2
1
1
4
1
1
1
1
REMARKS
2793160101
2773510103
0240060010
2773860103
2793640103
2773650103
2773870103
2793360103
2693370103
2793340113
2793350113
13210KA031
2793560111
2773691103
2773710103
2773690203
2773691313
2773500123
2773620100
2773620200
0149050020
0170050030
0110060020
2793020111
2793760101
0150040060
2793420111
2773520113
9802008280
0152060090
0110060010
0110080150
2773720301
0150040060
2773700103
0150040060
2793290113
2793590123
0023806000
0110060050
CAMSHAFT CP
PIN, CAMSHAFT, 9DX78.5L
O RING, 5.8DX9.6DX1.9T
SPRING PIN, 4DX7.5DX11L
RELEASE LEVER
CLIP, 13.8DX20.3DX0.4T
RETURN SPRING
VALVE SPRING, 17DX2.3DX27L N=5.8
SPRING RETAINER
INTAKE VALVE, 28.5DX5.5DX67.8L
EXHAUST VALVE, 26.5DX5.5DX67.8L
COLLET VALVE
TIMING CHAIN CP, 100 LINK
TENTIONER
SPRING, TENTIONER
PIN, TENTIONER, 6DX13DX34L
CHAIN GUIDE
PIN, ROCKER, 6DX9DX41L
ROCKER ARM ASSY. IN ........................... 1............. INCLUDES ITEMS W/
ROCKER ARM ASSY. EX .......................... 1............. INCLUDES ITEMS W/
ADJUST SCREW, M5X0.5X23L
NUT, M5X0.5X4.1H
FLANGE BOLT, M6X1.0X12L
MUFFLER, CP
SPARK ARRESTOR
TAPPING SCREW
MUFFLER COVER CP
GASKET, MUFFLER 26D 9DX58P 0.2T ... 1............. IN GASKET KIT IN CRANKCASE ASSY
FLANGE NUT
150
160
163
166
170
200
220
225
230
1
1
*
*
1
1
1
1
1
1
1
*
240
290
310
315
317
320
340
350
360
361
365
385
387
440
445
540
550
570
580
*
2
2
1
1
1
2
1
2
1
1
2
1
TAPPING BOLT, M6X1.0X10L
FLANGE BOLT, M6X1.0X8L
FLANGE BOLT, M8X1.25X12L
SCREEN CP
TAPPING SCREW
DEFLECTOR
TAPPING SCREW
INSULATOR
GASKET, INSULATOR
FLANGE NUT
FLANGE BOLT, M6X1.0X20L
QP- 40TE — OPERATION & PARTS MANUAL — REV. #0 (04/13/05) — PAGE 39
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EX270D50021 ENGINE — AIR CLEANER ASSY.
AIR CLEANER ASSY.
PAGE 40 — QP- 40TE —OPERATION & PARTS MANUAL — REV. #0 (04/13/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EX270D50021 ENGINE — AIR CLEANER ASSY.
AIR CLEANER ASSY.
NO.
PART NO.
PART NAME
QTY.
REMARKS
510
2793261200
2793263108
2793265008
2793264008
2793273008
2793274008
2793260707
0023806000
0110060050
AIR CLEANER ASSY., DUAL ............ 1 ............... INCLUDES ITEM W/
*
510-200
510-220
510-250
510-260
510-270
510-520
BASE CP
GASKET
COVER
LABEL
NUT
ELEMENT
FLANGE NUT
FLANGE BOLT
1
1
1
1
1
1
2
1
*
*
*
*
510-570
510-580
*
QP- 40TE — OPERATION & PARTS MANUAL — REV. #0 (04/13/05) — PAGE 41
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EX270D50021 ENGINE — GOVERNOR ASSY.
GOVERNOR GROUP ASSY.
PAGE 42 — QP- 40TE —OPERATION & PARTS MANUAL — REV. #0 (04/13/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EX270D50021 ENGINE — GOVERNOR ASSY.
GOVERNOR GROUP ASSY.
NO.
10
20
30
40
50
60
70
80
PART NO.
PART NAME
QTY.
1
REMARKS
2794230113
2274220133
2794270101
2774280113
0031305000
0130060240
0186060020
2794250223
2774330301
2774350103
0200060170
0217060070
0140060180
2374500423
0021706000
2774390203
0131050030
GOVERNOR LEVER
GOVERNOR SHAFT
GOVERNOR ROD CP.
ROD SPRING, 7DX0.5DX182L N=16
CLIP
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
BOLT AND WASHER ASSY.
NUT
GOVERNOR SPRING
SPEED CONTROL LEVER
STOP PLATE
WASHER, 6DX24DX2T
FRICTION WASHER, 6.5DX24DX0.8T
SCREW, M6X1.0X35L
SPRING, ADJUST
NUT
CLAMP
SCREW & WASHER ASSY.
SPEED CONTROL BRACKET CP ........... 1 ............ NOT AVAILABLE SEPARATELY
SCREW
310
*
340
350
355
360
365
370
395
396
435
440
450
480
485
486
490
*
*
*
*
*
*
*
*
*
*
*
*
0043104080
0023506000
2674510103
0110060020
2774370103
2774600303
1
1
1
2
1
SELF LOCK NUT
RETURN SPRING
FLANGE BOLT, M6X1.0X12L
LINK ROD
*
SPEED CONTROL ASSY ........................ 1 ............ INCLUDES ITEMS W/
*
QP- 40TE — OPERATION & PARTS MANUAL — REV. #0 (04/13/05) — PAGE 43
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EX270D50021 ENGINE — COOLING/ STARTING ASSY.
COOLING AND STARTING GROUP ASSY.
PAGE 44 — QP- 40TE —OPERATION & PARTS MANUAL — REV. #0 (04/13/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EX270D50021 ENGINE — COOLING/ STARTING ASSY.
COOLING AND STARTING GROUP ASSY.
NO.
10
20
40
60
61
80
81
210
210-1
210-2
210-3
210-4
210-5
210-6
210-7
210-11
210-35
210-49
220
PART NO.
PART NAME
QTY.
REMARKS
2795120201
0732005140
0110060030
2795271111
2795270213
0016508120
0110060020
2795020200
2265071608
2795012008
2795011008
2265070108
2795012508
2265073108
2265075208
2795014508
2265074108
2265075318
0110060010
BLOWER HOUSING CP., BLACK
LABEL, TRADE MARK 64D
FLANGE BOLT, M6X1.0X14DX14L
BAFFLE 1, CASE CP
BAFFLE 2, HEAD
1
1
4
1
1
1
1
BOLT
FLANGE BOLT, M6X1.0X14DX12L
RECOIL STARTER ASSY., D-STD. ...............1 ..........INCLUDES ITEM W/
SPIRAL SPRING
REEL
STARTER ROPE
STARTER KNOB
RATCHET
FRICTION SPRING
RATCHET SPRING
STARTER PULLEY
FRICTION PLATE
CENTER SCREW
FLANGE BOLT, M6X1.0XX14DX8L
*
1
1
1
1
2
1
2
1
1
1
4
*
*
*
*
*
*
*
*
*
QP- 40TE — OPERATION & PARTS MANUAL — REV. #0 (04/13/05) — PAGE 45
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EX270D50021 ENGINE — FUELTANK ASSY.
FUEL, LUBRICANT ASSY.
PAGE 46 — QP- 40TE —OPERATION & PARTS MANUAL — REV. #0 (04/13/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EX270D50021 ENGINE — FUELTANK ASSY.
FUEL, LUBRICANT ASSY.
NO.
10
20
23
30
40
48
60
63
80
90
PART NO.
PART NAME
QTY.
REMARKS
2796010211
0732005181
2799510103
0430430060
0641360010
0505120020
0023808000
0110080250
0851060000
0561100030
FUEL TANK CP., 3.6L BLACK
LABEL, WARNING
LABEL, MODEL
1
1
1
1
1
1
2
1
1
2
FUEL TANK CAP CP
FUEL, FILTER
UNION
FLANGE NUT
FLANGE BOLT, M8X1.25X25L
RUBBER PIPE, 6DX12D
HOSE CLAMP, 10DX8BX1T
QP- 40TE — OPERATION & PARTS MANUAL — REV. #0 (04/13/05) — PAGE 47
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EX270D50021 ENGINE — CARBURETOR ASSY.
CARBURETOR ASSY.
PAGE 48 — QP- 40TE —OPERATION & PARTS MANUAL — REV. #0 (04/13/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EX270D50021 ENGINE — CARBURETOR ASSY.
CARBURETOR ASSY.
NO.
PART NO.
PART NAME
QTY.
REMARKS
210
2796230200
2796253508
2516245008
2796252508
2796242008
2796252008
2796253008
2516245308
2796251508
2796255008
2516235008
2796254008
2796255008
2796240108
2796235508
2796256108
2796235308
2796244508
2796256208
27966250008
2796255208
2796245208
2796245108
CARBURETOR ASSY. ............................... 1 ................ INCLUDES ITEM W/
*
210-1
210-2
210-3
210-5
210-8
VALVE THROTTLE
SCREW
VALVE CHOKE
JET SLOW
SHAFT CHOKE
SHAFT SUB ASSY. THROTTLE
SCREW
PIN FLOAT LEVER
CHAMBER FLOAT
GASKET
GASKET CHAMBER
FLOAT, CHAMBER
JET MAIN
SCREW DRAIN
BUSH
SCREW ADJUSTING
SPRING
COLLAR
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
*
*
*
*
*
210-11
210-12
210-15
210-16
210-17
210-18
210-19
210-22
210-28
210-32
210-40
210-41
210-60
*
*
*
*
*
*
*
*
*
*
*
*
*
210-100
210-104
210-151
210-152
VALVE ASSY
GASKET
O-RING
O-RING
FILTER CUP
*
*
*
*
210-153
210-154
224
0642007810
0642006410
2774380101
27932902H3
2796230100
27935902H3
27935903H3
2794670103
1
1
1
1
1
1
1
1
*
*
PACKING, FILTER CUP
CHOKE LEVER CP
INSULATOR
225
226
CARBURETOR
227
GASKET1, INSULATOR
GASKET2, INSULATOR
GASKET
228
229
QP- 40TE — OPERATION & PARTS MANUAL — REV. #0 (04/13/05) — PAGE 49
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EX270D50021 ENGINE — FLYWHEEL ASSY.
FLYWHEEL ASSY.
PAGE 50 — QP- 40TE —OPERATION & PARTS MANUAL — REV. #0 (04/13/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EX270D50021 ENGINE — FLYWHEEL ASSY.
FLYWHEEL ASSY.
NO
10
PART NO
PART NAME
QTY.
REMARKS
2797924101
2797943001
2797930101
2797930201
0011406250
0011306200
0011306300
277731020H1
0660000371
0150040090
0650140150
0655000270
FLYWHEEL CP, 15W, 40W CHARGING 1
11
IGNITION COIL CP
1
1
1
2
2
2
1
1
12
LAMP COIL CP, 15W
LAMP COIL CP, 40W
BOLT & WASHER ASSY.
BOLT & WASHER ASSY., 15W
BOLT & WASHER ASSY., 40W
WIRE 1 CP
12
30
35
35
50
60
SWITCH ASSY.
70
TAPPING SCREW................................... 2.................... M4X10L
SPARK PLUG.......................................... 1.................... NGK BR6HS
100
`110
SPARK PLUG CAP
1
QP- 40TE — OPERATION & PARTS MANUAL — REV. #0 (04/13/05) — PAGE 51
Download from Www.Somanuals.com. All Manuals Search And Download.
EX270D50021 ENGINE — ELECTRIC DEVICE ASSY.
ELECTRIC DEVICE ASSY.
PAGE 52 — QP- 40TE —OPERATION & PARTS MANUAL — REV. #0 (04/13/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
EX270D50021 ENGINE — ELECTRIC DEVICE ASSY.
ELECTRIC DEVICE ASSY.
NO
700
705
740
741
770
775
PART NO
PART NAME
QTY.
REMARKS
2797630131
KU31107101
0011406160
0150040090
2147900601
0110060020
OIL SENSOR CP
CONTROL ASSY, OIL SENSOR
BOLT & WASHER ASSY.
TAPPING BOLT
1
1
2
2
1
1
CLAMP CP
FLANGE BOLT
QP- 40TE — OPERATION & PARTS MANUAL — REV. #0 (04/13/05) — PAGE 53
Download from Www.Somanuals.com. All Manuals Search And Download.
Effective: October 1, 2002
TERMS AND CONDITIONS OF SALE — PARTS
PAYMENT TERMS
5. Partsmustbeinnewandresalablecon- Multiquipreservestherighttoquoteandsell
dition,intheoriginalMultiquippackage(if directtoGovernmentagencies,andtoOriginal
any), and with Multiquip part numbers Equipment Manufacturer accounts who use
Terms of payment for parts are net 10 days.
FREIGHTPOLICY
clearlymarked.
our products as integral parts of their own
products.
All parts orders will be shipped collect or
prepaidwiththechargesaddedtotheinvoice.
All shipments are F.O.B. point of origin.
Multiquip’sresponsibilityceaseswhenasigned
manifesthasbeenobtainedfromthecarrier,
andanyclaimforshortageordamagemustbe
settledbetweentheconsigneeandthecarrier.
6. Thefollowingitemsarenotreturnable:
SPECIALEXPEDITINGSERVICE
a. Obsolete parts. (If an item is in the
price book and shows as being re- A$35.00surchargewillbeaddedtotheinvoice
placedbyanotheritem,itisobsolete.) forspecialhandlingincludingbusshipments,
insuredparcelpostorincaseswhereMultiquip
mustpersonallydeliverthepartstothecarrier.
(such as gaskets, seals, “O” rings,
b. Any parts with a limited shelf life
andotherrubberparts)thatwerepur- LIMITATIONSOFSELLER’SLIABILITY
MINIMUMORDER
chasedmorethansixmonthspriorto
thereturndate.
Multiquip shall not be liable hereunder for
damagesinexcessofthepurchasepriceofthe
The minimum charge for orders from Mul-
tiquipis$15.00net.Customerswillbeasked
for instructions regarding handling of orders
notmeetingthisrequirement.
c. Anylineitemwithanextendeddealer item with respect to which damages are
netpriceoflessthan$5.00.
claimed, and in no event shall Multiquip be
liable for loss of profit or good will or for any
otherspecial,consequentialorincidentaldam-
ages.
d. Special order items.
RETURNEDGOODSPOLICY
e. Electricalcomponents.
f. Paint,chemicals,andlubricants.
g. Decalsandpaperproducts.
h. Itemspurchasedinkits.
Returnshipmentswillbeacceptedandcredit
willbeallowed,subjecttothefollowingprovi-
sions:
LIMITATIONOFWARRANTIES
Nowarranties,expressorimplied,aremade
in connection with the sale of parts or trade
accessoriesnorastoanyenginenotmanufac-
tured by Multiquip. Such warranties made in
connectionwiththesaleofnew,completeunits
are made exclusively by a statement of war-
rantypackagedwithsuchunits,andMultiquip
neitherassumesnorauthorizesanypersonto
assume for it any other obligation or liability
whatever in connection with the sale of its
products.Apartfromsuchwrittenstatementof
warranty, there are no warranties, express,
impliedorstatutory,whichextendbeyondthe
descriptionoftheproductsonthefacehereof.
1. AReturnedMaterialAuthorizationmust
be approved by Multiquip prior to ship-
ment.
7. Thesenderwillbenotifiedofanymaterial
receivedthatisnotacceptable.
2. ToobtainaReturnMaterialAuthorization,
alistmustbeprovidedtoMultiquipParts
Salesthatdefinesitemnumbers,quanti-
ties, and descriptions of the items to be
returned.
8. Suchmaterialwillbeheldforfiveworking
days from notification, pending instruc-
tions.Ifareplyisnotreceivedwithinfive
days,thematerialwillbereturnedtothe
senderathisexpense.
a. Thepartsnumbersanddescriptions
must match the current parts price
list.
9. Creditonreturnedpartswillbeissuedat
dealer net price at time of the original
purchase,lessa15%restockingcharge.
b. The list must be typed or computer
generated.
10. In cases where an item is accepted, for
which the original purchase document
can not be determined, the price will be
basedonthelistpricethatwaseffective
twelvemonthspriortotheRMAdate.
c. The list must state the reason(s) for
thereturn.
d. The list must reference the sales
order(s)orinvoice(s)underwhichthe
itemswereoriginallypurchased.
11. Credit issued will be applied to future
purchasesonly.
e. The list must include the name and
phonenumberofthepersonrequest-
ingtheRMA.
PRICINGANDREBATES
Prices are subject to change without prior
notice.Pricechangesareeffectiveonaspe-
cificdateandallordersreceivedonorafterthat
datewillbebilledattherevisedprice.Rebates
3. AcopyoftheReturnMaterialAuthoriza-
tionmustaccompanythereturnshipment.
4. Freight is at the sender’s expense. All forpricedeclinesandaddedchargesforprice
partsmustbereturnedfreightprepaidto increaseswillnotbemadeforstockonhand
Multiquip’sdesignatedreceivingpoint.
atthetimeofanypricechange.
PAGE 54 — QP- 40TE —OPERATION & PARTS MANUAL — REV. #0 (04/13/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES PAGE
QP- 40TE — OPERATION & PARTS MANUAL — REV. #0 (04/13/05) — PAGE 55
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION & PARTS MANUAL
HERE'S HOW TO GET HELP
PLEASE HAVETHE MODEL AND SERIAL
NUMBER ON-HANDWHEN CALLING
UNITED STATES
Multiquip Corporate Office
18910 Wilmington Ave.
Carson, CA 90746
MQ Parts Department
800-427-1244
Tel. (800) 421-1244
Fax (800) 537-3927
Fax:800-672-7877
Fax:310-637-3284
310-537-3700
Contact: [email protected]
Mayco Parts
800-306-2926
310-537-3700
Warranty Department
800-421-1244, Ext. 279 Fax:310-537-1173
310-537-3700, Ext. 279
Fax:800-672-7877
Fax:310-637-3284
Service Department
800-421-1244
Technial Assistance
800-478-1244
Fax:310-537-4259
Fax:310-631-5032
310-537-3700
MEXICO
MQ Cipsa
UNITED KINGDOM
Multiquip (UK) Limited Head Office
Hanover Mill, Fitzroy Street,
Ashton-under-Lyne,
Carr. Fed. Mexico-Puebla KM 126.5
Momoxpan, Cholula, Puebla72760Mexico
Tel: (52) 222-225-9900
Fax: (52) 222-285-0420
Tel: 0161 339 2223
Fax: 0161 339 3226
Lancashire OL7 0TL
CANADA
Multiquip
BRAZIL
Multiquip
4110IndustrielBoul.
Laval, Quebec, Canada H7L 6V3
Tel: (450) 625-2244
Fax: (450) 625-8664
Av. Evandro Lins e Silva, 840 - grupo 505 Tel: 011-55-21-3433-9055
Barra de Tijuca - Rio de Janeiro Fax: 011-55-21-3433-9055
© COPYRIGHT 2005, MULTIQUIP INC.
Multiquip Inc and the MQ logo are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without written permission. All other trademarks are
the property of their respective owners and used with permission.
This manual MUST accompany the equipment at all times. This manual is considered a permanent part of the equipment and should remain with the unit if resold.
The information and specifications included in this publication were in effect at the time of approval for printing. Illustrations are based on the QP-40TE Trash Pump.
Illustrations, descriptions, references and technical data contained in this manual are for guidance only and may not be considered as binding. Multiquip Inc. reserves the
right to discontinue or change specifications, design or the information published in this publication at any time without notice and without incurring any obligations.
Your Local Dealer is:
Download from Www.Somanuals.com. All Manuals Search And Download.
|